SHARE Knowledge Hub
Hazard group - electrical hazards
Electrical hazards arise from contact with electricity, electrical faults or the release of electrical energy during work on or near installations and equipment. Harm can include electric shock, burns, arc-related injury, fire and secondary injury from a fall or sudden movement. Risk occurs during normal use as well as installation, testing, cleaning, maintenance and fault finding, particularly where equipment is damaged or conditions are wet, temporary or confined. Assessment considers voltage, available energy, exposed conductors, supply arrangements, equipment suitability and other energy sources. Work should avoid exposure where possible and use competent planning, secure isolation, verification and suitable protection. Live work requires specific legal justification and safeguards; general guidance does not authorise it. SHARE links this group to electrical safety, isolation and maintenance topics for task-specific control decisions.
Understanding Hazard group - electrical hazards
Electrical hazards arise from contact with electricity, electrical faults or the release of electrical energy during work on or near installations and equipment. Harm can include electric shock, burns, arc-related injury, fire and secondary injury from a fall or sudden movement. Risk occurs during normal use as well as installation, testing, cleaning, maintenance and fault finding, particularly where equipment is damaged or conditions are wet, temporary or confined. Assessment considers voltage, available energy, exposed conductors, supply arrangements, equipment suitability and other energy sources. Work should avoid exposure where possible and use competent planning, secure isolation, verification and suitable protection. Live work requires specific legal justification and safeguards; general guidance does not authorise it. SHARE links this group to electrical safety, isolation and maintenance topics for task-specific control decisions.
Why this matters at work
Weather can change exposure, access, equipment suitability and emergency communication. Lightning is distinct from an ordinary equipment fault; rain and flooding may damage electrical arrangements or leave downed cables and inaccessible assets. Obtain fresh weather and site information for an actual decision. The archived Met Office warnings page records a changing service and possible outdated display, not a reliable no-warning permission to work. Met Office seasonal advice supports anticipatory planning and avoiding exposure; it does not specify this site's lightning protection, shutdown trigger or safe distance.
Damage can arise between scheduled inspections through flexing, pulling, crushing, transport or cleaning. User checks and reporting provide a route to detect visible defects before further use; they are not specialist tests. Make quarantine practical: identify the affected item, prevent accidental reuse, tell the responsible person and supply an assessed replacement where needed. Avoid tape as a general repair method and leave repair or replacement decisions to competent arrangements. Physical protection and cable routing should address the cause, otherwise a repaired lead returns to the same damaging conditions.
How organisations manage this in practice
PAT is one possible part of a maintenance system, not a universal legal ritual. HSE's FAQ states that the law does not impose annual portable appliance testing or blanket PAT label and record requirements. Maintenance must still prevent danger. User checks, formal visual inspections and competent combined inspection and testing find different problems; visual inspection can identify damage a test does not, while testing can identify hidden faults. Choose the combination and review periods for equipment, use, movement, environment and defect history. Do not copy a guidance table as a universal legal frequency.
For portable tools and planned maintenance, identify supply arrangements, access to conductors, wet conditions, temporary wiring, overhead lines and who is authorised to isolate and work on the system. Select suitable equipment, protect cables and maintain systems according to risk. Plan work dead wherever possible and use competent electrical personnel for isolation and verification. Restrict access and manage overhead line interfaces. Electrical asset register; risk based inspection and maintenance schedule; defect quarantine; competence records; isolation planning; contractor coordination and temporary supply checks. Follow the assessment through procurement, implementation, briefing, supervision and verification rather than stopping at a document.
Records and labels can help manage work and trace decisions even though HSE does not impose them as universal PAT requirements. Keep useful asset identity, maintenance basis, findings, action and review information, and show how recurring damage changes the plan. Verify that users understand their checks and know when to report, while personnel performing technical tests have suitable competence. Review the system when equipment is hired, relocated, modified or exposed to harsher conditions. The selected guidance does not supply blanket clearance for major plant, generators or electromedical equipment.
What are electrical hazards and what does their assessment cover?
Electrical hazards include shock, burns, fire and secondary injury. Assess equipment and work on or near conductors, including temporary supplies and high energy systems. A generic guide cannot specify an arc flash boundary or high voltage switching procedure. Obtain competent design and task specific advice. Portable appliance testing (PAT) is not a substitute for an overall electrical maintenance system. See Electricity at work: Safe working practices and Maintaining portable electrical equipment.
Start with the hazard group overview, then use the related topic links for task-specific background. A group checklist helps discovery; it does not establish that the controls at your site are effective. Read the hazard group overview.
Which hazards should the assessment consider?
Check each relevant mechanism during normal work, cleaning, maintenance, foreseeable failure and emergencies. Several entries can share a harm pathway; follow the linked explanation rather than treating each label as a separate assessment. See Electricity at work: Safe working practices and Maintaining portable electrical equipment.
Hazard or exposure and practical application — part 1 of 4
Read the complete visual as text
- Electric shock: Read the mechanism and controls: Shock exposed wires and damaged cables
- Exposed wires: Read the mechanism and controls: Shock exposed wires and damaged cables
- Damaged cables: Read the mechanism and controls: Shock exposed wires and damaged cables
- Arc flash: Read the mechanism and controls: Arc flash and high voltage
Hazard or exposure and practical application — part 2 of 4
Read the complete visual as text
- High voltage: Read the mechanism and controls: Arc flash and high voltage
- Overloaded circuits: Read the mechanism and controls: Earthing and overloaded circuits
- Inadequate earthing / faulty protective arrangements: Read the mechanism and controls: Earthing and overloaded circuits
Hazard or exposure and practical application — part 3 of 4
Read the complete visual as text
- Faulty equipment: Read the mechanism and controls: Wet conditions faulty equipment and portable tools
- Wet conditions with electricity: Read the mechanism and controls: Wet conditions faulty equipment and portable tools
- Portable electrical tool hazards: Read the mechanism and controls: Wet conditions faulty equipment and portable tools
Hazard or exposure and practical application — part 4 of 4
Read the complete visual as text
- Temporary wiring: Read the mechanism and controls: Temporary wiring
- Static electricity: Read the mechanism and controls: Lines services static and lightning
- Lightning: Read the mechanism and controls: Lines services static and lightning
Describe when the source is created or released and how it reaches someone. Compare normal operation with receipt, setup, blockage, breakdown, disposal and contractor access. The list below is a discovery aid: an omitted mechanism may still be important, while an irrelevant item does not require a fabricated assessment. Follow the mechanism explanation and test controls against the actual circumstances before scoring risk.
| Hazard or exposure | Read the mechanism and controls |
|---|---|
| Electric shock | Shock exposed wires and damaged cables |
| Exposed wires | Shock exposed wires and damaged cables |
| Damaged cables | Shock exposed wires and damaged cables |
| Arc flash | Arc flash and high voltage |
| High voltage | Arc flash and high voltage |
| Overloaded circuits | Earthing and overloaded circuits |
| Inadequate earthing / faulty protective arrangements | Earthing and overloaded circuits |
| Faulty equipment | Wet conditions faulty equipment and portable tools |
| Wet conditions with electricity | Wet conditions faulty equipment and portable tools |
| Portable electrical tool hazards | Wet conditions faulty equipment and portable tools |
| Temporary wiring | Temporary wiring |
| Static electricity | Lines services static and lightning |
| Lightning | Lines services static and lightning |
How can electrical energy cause shock, burns or a secondary injury?
Electricity can cause shock, burns, fire and secondary injuries such as falls. Fault energy, the installation, access and environmental conditions matter, not simply the equipment voltage label. Assess ordinary use separately from work on or near conductors. Damaged insulation, moisture, unexpected energisation and temporary alterations change the risk. Workers recognise defects and stop using affected equipment; specialised electrical decisions require suitable competence and authority. See Electricity at work: Safe working practices and Electrical safety.
Distinguish direct contact, a fault making accessible metalwork dangerous, thermal or arc effects and the secondary consequences of involuntary movement. A damp area, damaged cable or changed supply can alter risk without changing the task name. Design, protective systems, competent isolation and maintenance are therefore linked. This is awareness and planning guidance; it does not provide a live-working method or authorise an unqualified person to test a system.

How can electricity injure the body, and why can a small mark hide a serious incident?
Interactive anatomy · Electrical injury · Updated 2026-10-23
Electrical injury terms
A broad term for injury associated with electrical exposure.
An external current affecting the body.
Tissue injury caused by electrical heating.
Death from electric shock.
Health and Safety Executive: Electrical injuries · Health and Safety Executive: Selection and use of electric handlamps, PM38 · NHS: Burns and scaldsRead all anatomy and process explanations without the viewer
General occupational awareness of anatomy and incident mechanisms. A broad term for injury associated with electrical exposure. An external current affecting the body. Tissue injury caused by electrical heating. Death from electric shock. Electrical rescue, live testing, isolation or energised work instruction An energise-person control, contact timer, voltage or resistance input Safe current paths, survival percentages or shock-severity scores ECG interpretation, rhythm selection or AED shock decisions Medical or workplace clearance from a mark, diagram or feeling well The hazard-avoidance and medical-help panel is visible before model loading and quiz completion.
Nerve pathway
Nerves communicate using electrical and chemical signals. Nerves carry biological signals, and communication at the nerve-to-muscle connection helps activate muscle. The travelling cue is a simplified way of directing attention to that relationship. It does not show household current circulating through a person, and its colour, speed or brightness cannot be used to interpret nerve function or electrical injury. Alder Hey Children’s NHS Foundation Trust: Nerve service — normal nerve function · NHS: Lambert-Eaton myasthenic syndrome — normal nerve-to-muscle signalling · Oxford University Hospitals NHS Foundation Trust: Nerve Conduction Studies and Electromyography
Skeletal muscle
The nervous system normally coordinates muscle contraction. A slow hand movement demonstrates normal function; it does not imitate a casualty’s involuntary movements. Alder Hey Children’s NHS Foundation Trust: Nerve service — normal nerve function · NHS: Lambert-Eaton myasthenic syndrome — normal nerve-to-muscle signalling
Breathing muscles
Coordinated muscle activity helps move air into and out of the lungs. The diaphragm and chest movement belong to the respiratory lesson. This example shows no breathing-rate measurement. Cambridge University Hospitals NHS Foundation Trust: Breathing pattern disorders and physiotherapy — normal diaphragm role
Heart conduction
Coordinated electrical activity helps organise the heart’s pumping. A labelled sequence illustrates normal biological activation. It is not an ECG or a rhythm-interpretation exercise. St George’s University Hospitals NHS Foundation Trust: Catheter Ablation for Supra-Ventricular Tachycardia — normal electrical system · NHS 111 Wales: Cardiac Arrest
Skin contact region
Contact conditions influence how an electrical exposure affects the body. The marker identifies an example contact region. It does not calculate skin resistance or identify a safe point to touch. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Electrical safety frequently asked questions
Internal tissue region
Electrical injury can extend beneath the visible surface. An electrical incident can cause effects below the surface, so visible appearance alone cannot describe the whole injury. This transparent region marks the subject of the explanation, rather than a measured boundary of damage. Its shape does not establish where current travelled or which tissues are unaffected; compare it with the selected mechanism caption. Health and Safety Executive: Electrical injuries · NHS: Burns and scalds · NHS 111 Wales: Burns and scalds — electrical burns
External source
The incident hazard comes from an electrical source outside the body. The generic equipment symbol is kept disconnected from the normal biological signalling diagram. Health and Safety Executive: Introduction to electrical safety
Illustrative exposure route
This broad region represents one possible exposure route. It cannot establish the actual route or outcome. There is no safe-path selector, voltage control or timed-contact exercise. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Electrical safety frequently asked questions
Arc and thermal region
An arc or hot electrical equipment can cause injury. This separate incident panel is different from a simple through-body current diagram. No arc flash is animated. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Introduction to electrical safety
Secondary injury
Loss of control can lead to falls or contact with nearby hazards. The neutral surrounding-hazard symbol recognises these injuries without staging a fall or body jerk. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Introduction to electrical safety
Response boundary
Keep clear of unresolved electrical danger and get emergency help. Do not touch a person who may still be in contact with an electrical source. This node opens the safety panel, never a rescue activity. Health and Safety Executive: Introduction to electrical safety · Health and Safety Executive: Electricity — electric shock and overhead-line precautions · Health and Safety Executive: Emergency procedures
Open the complete process transcript
The process, step by step
Explore normal function
Start with the body’s own signalling: nerves communicate with muscles, breathing muscles move the chest, and organised activation coordinates the heart. Select one example at a time and read the associated label before changing systems. These are normal biological functions, not electricity from equipment moving through a person. The slow cues make the explanation easier to follow; they do not show a measured nerve signal, breathing rate or heart rhythm. This process sequence is a teaching route through the subject, not a simulation of an electrical accident. Alder Hey Children’s NHS Foundation Trust: Nerve service — normal nerve function · NHS: Lambert-Eaton myasthenic syndrome — normal nerve-to-muscle signalling · Cambridge University Hospitals NHS Foundation Trust: Breathing pattern disorders and physiotherapy — normal diaphragm role · St George’s University Hospitals NHS Foundation Trust: Catheter Ablation for Supra-Ventricular Tachycardia — normal electrical system
What to watch: Select the nerve, skeletal-muscle, breathing-muscle and heart labels individually, noticing that each belongs to a different normal biological example.
Why it matters: Normal signalling helps muscles work in a coordinated way. Keeping these biological examples distinct from the incident diagrams makes it easier to explain what an external electrical hazard can disrupt.
Explore this step: Explore one normal system, then explain its function before selecting a different system.
Locate the external hazard
Locate the generic electrical-source symbol outside the body and compare it with the normal biological labels. It represents an external workplace hazard, not the source of ordinary nerve or heart signalling. The model keeps the equipment symbol separate and does not energise the silhouette when a learner selects it. This step establishes the context before the different injury mechanisms are discussed. A picture of equipment cannot show whether real equipment is safe. Use the label to identify the distinction, rather than imagining that the model is testing a circuit. Health and Safety Executive: Introduction to electrical safety · Health and Safety Executive: Emergency procedures
What to watch: Locate the external-source symbol and the response-boundary label, then compare their positions with the normal body-system labels.
Why it matters: An external electrical supply is a hazard that requires competent control. Separating it from biological signalling avoids implying that a normal nerve pathway describes a safe route for electrical current.
Explore this step: Identify which labels describe the body and which identify the external hazard or safety boundary.
Choose an incident example
Choose one incident explanation: electric shock, electrical heating within tissue, or an arc and its thermal effects. These are different mechanisms and more than one may be relevant to an incident. Read the selected heading before examining the highlighted region so that the image and explanation remain connected. The model is a route through the concepts, not a calculation of current flow or injury severity. It provides no voltage control, safe-contact experiment or animated arc. Compare the labels to explain how the mechanisms differ without ranking an actual casualty’s injuries. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Introduction to electrical safety
What to watch: Read the incident heading, then locate its contact, internal-tissue or arc-and-thermal label rather than combining every marker into one route.
Why it matters: Shock can disturb body function, while heating can injure tissue. An arc can cause thermal injury without being equivalent to the simple contact diagram; the examples can overlap in a real incident.
Explore this step: Compare two incident panels and describe the different mechanism named by each heading.
Explain possible effects
Read the caption beside the selected system and trace the labelled relationship being explained. Electric shock can interfere with muscle control, breathing or the way the heart beats; electrical heating can damage tissue. The highlighted region is a teaching focus, not a map of an individual’s injury. It cannot identify the actual route through the body or declare that an unhighlighted organ is unaffected. Compare the normal-function labels with the incident caption, keeping the possible effect separate from any claim about what has happened to a particular person. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Electrical safety frequently asked questions
What to watch: Compare the breathing-muscle, heart and internal-tissue labels with the caption for the incident mechanism currently selected.
Why it matters: Interference with coordinated muscle or heart function can be serious even when an illustration shows little surface change. A teaching marker cannot determine which effects are present or absent in a real person.
Explore this step: Choose a system and describe its normal role before reading the possible effect in the incident caption.
Know the limits
Finish by comparing the questions the diagram answers with those it cannot answer. It can introduce normal signalling and distinguish several possible injury mechanisms. It cannot establish an actual exposure, the extent of damage, a safe electrical condition or medical clearance. A small-looking electrical burn or feeling well does not provide that clearance. The external-source and response-boundary labels keep these limits visible. Review them alongside the existing safety panel; completing this teaching route is not a rescue procedure, a clinical assessment or permission to resume the work. NHS: Burns and scalds · Health and Safety Executive: Electrical safety frequently asked questions · NHS 111 Wales: Burns and scalds — electrical burns
What to watch: Locate the internal-tissue and response-boundary labels, then compare the limits stated in their captions with the incident explanation.
Why it matters: Visible appearance alone cannot establish the seriousness of electrical injury. Keeping the model’s scope clear prevents an explanatory picture or completed activity being mistaken for evidence that a person or workplace is safe.
Explore this step: Name one question the model explains and one question that requires assessment beyond this teaching view.
Mechanisms and their limits
Electric shock: disruption of normal function External electrical current can interfere with muscle control, breathing or the heart’s organised activity. These are possible effects; the same diagram cannot predict the outcome of a real incident. An illustrative route does not show that a particular organ must or cannot be affected. No arbitrary arrhythmia, dramatic flatline, body jerk or calculated survival result is shown. Both alternating and direct current can be dangerous. The viewer offers no safe voltage or safe path. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Electrical safety frequently asked questions
HSE: prevent electrical injury
Electrical heating: injury beneath the surface Current passing through tissues can generate heat and cause burns beneath the skin. A small visible mark is not enough to judge the internal effects. Not every shock produces extensive burns. The marked region is illustrative, not a reconstructed path, calculated burn depth or severity score. An electrical burn needs emergency medical assessment even if it appears small. Feeling well or selecting a similar image does not provide workplace or medical clearance. Health and Safety Executive: Electrical injuries · NHS: Burns and scalds · NHS 111 Wales: Burns and scalds — electrical burns
NHS: electrical burns need emergency care
HSE: electrical injury mechanisms
Arc, heat and secondary injury Arcing and hot electrical equipment can injure people without the event fitting a simple hand-to-foot contact story. Heat, fire or explosion and secondary falls or nearby machinery may add hazards. The diagram does not require a through-body route to recognise an arc or thermal hazard. Alternating and direct current equipment can both present hazards. This is an incident explanation, not a flash-energy calculation or permission to approach damaged equipment. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Introduction to electrical safety · Health and Safety Executive: Electrical safety frequently asked questions
HSE: electrical hazards and controls
HSE: competent assessment of unsafe equipment
Electric shock: disruption of normal function — follow the anatomy
Look at: The contact route through the body, including nerves and muscle.
What changes: Electric current can interfere with normal nerve, muscle, breathing or heart activity.
Why it matters: A person may be unable to let go, collapse or develop a dangerous rhythm.
What to do: Keep clear, do not touch anyone still in contact with electricity, call 999 and follow competent site emergency arrangements.
Damaged portable equipment presents an unresolved electrical hazard
A worker finds damaged equipment near a damp work area; the exposure is a counterfactual failure of controls, not a rescue exercise. An acute incident is explained in 32 seconds without voltage, current or contact-duration inputs. The sequence sets no safe exposure or waiting time. Never touch a person or equipment while electrical danger is unresolved. The viewer cannot prove isolation or infer the actual current path or outcome.
Keep clear of the unresolved source Damaged equipment in a damp area is a stop-and-report situation. Do not touch a potentially live casualty; call appropriate help and use competent site emergency arrangements. Health and Safety Executive: Electrical safety frequently asked questions · Health and Safety Executive: Emergency procedures
What failed barriers could allow The counterfactual contact example marks an external source and possible exposure. It does not ask the learner to energise a person or select a supposedly safe route. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Electrical safety frequently asked questions
Possible interference with normal function External current can affect muscle control, breathing or heart function. These are possible effects, not a prediction that every organ is involved or that a particular contact is survivable. Health and Safety Executive: Electrical injuries
Safety first, then urgent assessment Keep clear and obtain emergency help while danger remains. Only once the scene is safe does the separate unresponsive/abnormal-breathing CPR/AED guidance apply. Feeling well does not provide medical or equipment clearance. Health and Safety Executive: Electrical safety frequently asked questions · NHS: Burns and scalds · NHS 111 Wales: Cardiac Arrest · Health and Safety Executive: Emergency procedures
Electrical heating: injury beneath the surface — follow the anatomy
Look at: The tissue beneath the electrical contact points.
What changes: Current can generate heat inside the body as well as at the skin.
Why it matters: A small visible mark can conceal serious deeper injury.
What to do: Keep the scene safe; electrical burns need 999 or A&E assessment even when the visible mark is small.
A small external mark after an electrical incident
After an electrical incident, a worker has a small visible hand mark; the area must be made safe by competent arrangements. This is a possible injury explanation, not a burn-depth model or a simulation of tissue heating at a selected exposure time. Visible marks cannot establish the route or depth of internal injury. Not every shock produces the broad affected area used in this illustration.
Do not approach unresolved energy danger The incident is treated as an electrical emergency until the scene is safe. Keep clear, summon appropriate help and do not judge safety from a small mark. Health and Safety Executive: Electrical safety frequently asked questions · NHS: Burns and scalds
External current can heat tissues A broad translucent region represents possible tissue heating during contact. It is not a wire tracing the real route and it does not calculate dose from a contact point. Health and Safety Executive: Electrical injuries
An external mark may understate injury The selected region separates possible internal effects from the skin marker. Size or appearance of the mark cannot clear the person or tell the learner what tissues were actually injured. Health and Safety Executive: Electrical injuries · NHS 111 Wales: Burns and scalds — electrical burns
Arrange medical assessment Use emergency help for electrical burns and follow live advice once it is safe to assist. Do not continue work or reassure someone simply because the mark is small; the activity gives no treatment or return-to-work clearance. NHS: Burns and scalds · NHS 111 Wales: Burns and scalds — electrical burns · Health and Safety Executive: Emergency procedures
Arc, heat and secondary injury — follow the anatomy
Look at: The skin and eyes facing the arc, and the worker’s surroundings.
What changes: An electrical arc releases intense heat; the event may also cause a fall or other trauma.
Why it matters: Burns and secondary injuries can occur without a current path through the body.
What to do: Control arc hazards, use competent isolation procedures and plan emergency response.
An electrical fault releases heat near a work area
A fault or overheated electrical component exposes people nearby to heat and possible secondary hazards. The short explanation omits flashes, noise and blast effects. It predicts no arc boundary, burn depth, safe distance or survival probability. Arc/thermal injury is separate from the through-body current example. A person need not supply a hand-to-foot contact story for the incident to be serious.
Treat the fault as unresolved danger Keep clear of faulty or overheated equipment and activate competent emergency arrangements. The example gives no permission for live inspection or repair. Health and Safety Executive: Introduction to electrical safety · Health and Safety Executive: Electrical safety frequently asked questions · Health and Safety Executive: Emergency procedures
Heat can be released without the chosen contact route The equipment-and-person schematic marks hot material or thermal exposure. No bright flash or energise-person action is used to teach the incident. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Introduction to electrical safety
Possible thermal and secondary injury Heat may injure tissue, and a loss of control or sudden movement may lead to falls or contact with surrounding hazards. These possibilities remain separate from a reconstructed internal current path. Health and Safety Executive: Electrical injuries
Control the danger and get help Follow site emergency arrangements and obtain medical help for injuries once safe to assist. Competent investigation must address the fault; no visual improvement in the model clears the equipment or the worker. NHS: Burns and scalds · Health and Safety Executive: Electrical safety frequently asked questions · Health and Safety Executive: Emergency procedures
Read the practice situations and all answer explanations
EL-Q1: What can be concluded from the mark?
A colleague has had an electrical incident and has only a small visible mark.
It proves the event was harmless. — A small mark cannot rule out internal effects. Electrical burns need emergency care.
Internal effects cannot be judged from the mark; seek appropriate medical assessment. — Correct. Do not use appearance as reassurance. Keep the area safe and obtain appropriate medical help; an electrical burn requires 999 or A&E.
Select the closest route in the model to calculate survival. — The model cannot reconstruct the incident or predict survival. Seek appropriate help instead of matching an image.
Health and Safety Executive: Electrical injuries · NHS: Burns and scalds · NHS 111 Wales: Burns and scalds — electrical burnsEL-Q2: Which response avoids creating another casualty?
Someone may still be in contact with a live electrical source.
Touch them immediately to pull them away. — Do not touch them while the electrical danger is unresolved. You could also be injured. Call for emergency help.
Keep clear, call emergency help and follow competent site emergency arrangements. — Correct. Call 999 and explain that electricity is involved. Keep others clear and follow competent emergency arrangements; this lesson does not teach electrical rescue or isolation.
Use the viewer to find the safest current path. — There is no safe-path or rescue method in this viewer. Keep clear and get emergency help.
Health and Safety Executive: Introduction to electrical safety · Health and Safety Executive: Electricity — electric shock and overhead-line precautions · Health and Safety Executive: Emergency proceduresEL-Q3: What still needs consideration?
An arc incident happens without an obvious hand-to-foot contact route.
There cannot be an injury without that route. — A simple through-body route is not required for an arc/thermal injury or a secondary fall.
Arc, heat and secondary injuries. — Yes. Consider the incident hazards and obtain appropriate help rather than forcing the event into one current-path drawing.
Direct-current equipment cannot cause harm. — Both AC and DC equipment can be hazardous. Neither label provides reassurance.
Health and Safety Executive: Electrical injuries · Health and Safety Executive: Introduction to electrical safety · Health and Safety Executive: Electrical safety frequently asked questionsSources and how the model is made
The opening images are AI-generated anatomical illustrations. The interactive 3D models and labelled SVG diagrams use original procedural artwork. These teaching images are not medical scans or diagnostic tools. Source references support the learner explanations and do not grant artwork rights.
- Health and Safety Executive: Electrical injuries — Possible shock effects, deep tissue heating, loss of muscle control, thermal and secondary injuries; AC and DC hazards. No numerical voltage/contact-time thresholds transferred.
- Health and Safety Executive: Introduction to electrical safety — Contact, arcing, fire/explosion and secondary falls; suitable equipment and competent maintenance/assessment. No isolation or live-work procedure generated.
- Health and Safety Executive: Selection and use of electric handlamps, PM38 — Page 1 defines electrocution as death from electric shock; replaces the brief’s US terminology source. No equipment specification or voltage rule copied into this awareness lesson.
- NHS: Burns and scalds — Current page reviewed 31 March 2026: electrical burns require 999 or A&E. No chemical-skin or eye-irrigation timer substituted.
- Alder Hey Children’s NHS Foundation Trust: Nerve service — normal nerve function — Basic biological electrical signalling and motor/sensory roles only. No paediatric injury prognosis or treatment transferred to the occupational module.
- NHS: Lambert-Eaton myasthenic syndrome — normal nerve-to-muscle signalling — Normal nerve signalling followed by chemical communication to activate muscle. Disease mechanisms and treatment are outside this module.
- Oxford University Hospitals NHS Foundation Trust: Nerve Conduction Studies and Electromyography — Natural electrical signals in nerves and muscle activity. No diagnostic procedure, test voltage or stimulation activity reused.
- Cambridge University Hospitals NHS Foundation Trust: Breathing pattern disorders and physiotherapy — normal diaphragm role — Diaphragm movement and air movement during breathing only. No exercise programme, self-assessment or rate target reused.
- St George’s University Hospitals NHS Foundation Trust: Catheter Ablation for Supra-Ventricular Tachycardia — normal electrical system — Page 2 normal cardiac electrical activation coordinating contraction. Printed review date October 2026 needs recheck at sign-off. No clinical procedure, ECG or third-party artwork copied.
- Health and Safety Executive: Electrical safety frequently asked questions — AC/DC hazards, multifactorial outcome uncertainty and need for competent safety assessment. No safe-voltage, resistance, RCD guarantee or risk score imported.
- NHS 111 Wales: Burns and scalds — electrical burns — A small-looking electrical burn can be very damaging and needs immediate medical attention. No household separation/rescue procedure copied.
- NHS 111 Wales: Cardiac Arrest — Unresponsive and absent/abnormal breathing, gasping, immediate 999/CPR/call-handler/AED recognition pathway. Applies only after electrical danger is resolved. No clinical ECG decision or full CPR course.
- Health and Safety Executive: Electricity — electric shock and overhead-line precautions — Do not touch a casualty while electrical danger remains; stay clear and warn others; first aid requires training. No separation technique, escape manoeuvre or rescue distance imported.
- Health and Safety Executive: Emergency procedures — Competent emergency control, calling emergency services, site arrangements and no resumption while serious danger remains. No procedural isolation instruction generated.
Why must safe isolation and maintenance be planned for the actual equipment?
Plan work dead wherever possible, with competent isolation, prevention of re-energisation and verification under the authorised system. Switching off a local control does not prove safety. Production convenience alone does not justify live work. User checks, formal visual inspection and testing serve different purposes. Their mix and frequency reflect equipment, environment, use and defect history; annual PAT is not a universal solution. Include fixed installations, temporary supplies and contractor coordination. See Electricity at work: Safe working practices and Maintaining portable electrical equipment.
The authorised competent person plans isolation and verifies the safe condition for the actual system, including relevant sources that could reintroduce energy. Users need clear defect reporting and equipment withdrawal, not instructions to investigate live parts. Maintenance decisions depend on equipment, use, environment and fault evidence. A fixed test schedule or a recent label cannot by itself establish current suitability after damage, wetting or modification.
How can damaged cables or exposed conductors cause an electric shock?
Contact with energised parts or metal made live by a fault can injure people. Cables can be cut, crushed or pulled apart between inspections. See Electrical safety and you: A brief guide and Maintaining portable electrical equipment.
A cleaner contacts damaged insulation, an installer encounters an exposed conductor or a tool user handles a cable damaged by traffic. Current passing through the body can affect muscles, breathing or heart function and cause burns; a startled movement can cause a fall. The visible damage may not reveal all live parts.
Which source controls and checks change the outcome?
Avoid exposed electrical contact through suitable design, containment and removal of defective equipment. A competent person selects and verifies the protective arrangement and planned maintenance; users only make checks within their instruction. Keep people away and stop using suspected unsafe equipment. Do not touch a person still in contact with an electrical source or attempt a repair beyond authorisation; use the site emergency route and competent isolation arrangements.
How should the controls be applied?
Select suitable equipment, protect cables, quarantine defects and prevent unauthorised repairs. Use protective arrangements specified by competent personnel.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Inspect actual routes and record repair and return-to-service decisions. Tape over damage is not a general repair method.
Why do arc flash and high-voltage work require specialist arrangements?
Faults can release heat, pressure and projected material. Opening an enclosure creates different exposure from ordinary use. See Electricity at work: Safe working practices.
An electrical fault or inappropriate intervention at switchgear can release intense heat, light, pressure and molten material. A worker need not directly touch a conductor to suffer severe burns or impact injury. Equipment condition, fault conditions and operating method require specialist consideration, not a generic portable-tool check.
Which source controls and checks change the outcome?
Avoid live intervention and arrange safe working dead wherever required and feasible through competent planning. Specialist designers and authorised electrical staff determine equipment, access, protection and operating arrangements for the actual system. Keep unqualified people outside controlled access. Personal protective equipment (PPE), if required, must come from the competent assessment and does not make an unjustified live task acceptable. Stop on unknown system details, condition concerns or missing authorisation; do not guess arc ratings or boundaries.
How should the controls be applied?
Avoid exposure through design, working dead, access restriction and competent task planning. Use installation-specific engineering assessment.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. No arc boundary, switching sequence or PPE category is supplied by this general document. Obtain competent specifications.
How can earthing faults or overloaded circuits cause harm?
Defective protective arrangements, excess loading and unsuitable modifications can cause shock or fire. More sockets do not increase supply capacity. See Electricity at work: Safe working practices and Electrical safety and you: A brief guide.
A damaged protective arrangement can leave accessible metalwork dangerous after a fault, while unsuitable loading can heat connections or cables. Extensions and changed equipment can alter the installation demand. A device powering up normally does not prove the protective system is effective.
Which source controls and checks change the outcome?
Design the installation and equipment selection for the actual load and environment, with competent protection and maintenance. Managers prevent uncontrolled additions and require assessment before equipment or layout changes. Users report heat, burning smell, damage or abnormal operation without opening equipment or testing beyond their competence. Remove affected equipment from use and obtain competent checks; repeated trips must not be treated as a reason to bypass protection or increase a rating.
How should the controls be applied?
Use competent design and maintenance; control extensions and modifications and assess loading before connecting additional equipment.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Obtain installation evidence. Working equipment does not prove protective conductor integrity.
How do wet conditions change the risk from a portable tool?
Water, conductive surroundings and harsh handling alter suitability. An office appliance may not suit a wet work site. See Maintaining portable electrical equipment and Electrical safety.
Rain reaches an outdoor connector, a cleaner uses a tool near water or a maintenance employee carries equipment from a dry store into a damp area. Moisture and damage can change contact and fault conditions; a label from an earlier test says nothing about a newly crushed cable or unsuitable enclosure.
Which source controls and checks change the outcome?
Avoid electrical equipment where suitable or select a system designed for the task and environment, with competent advice. Protect equipment and cables against water, impact and traffic, and use the maintenance and supply protection specified by the assessment. Users check visible condition and stop for damage or unsuitable conditions. Do not dry, reconnect or open suspect equipment as an improvised repair; a competent authorised person decides on investigation and return to service.
How should the controls be applied?
Choose suitable equipment and supplies, protect connectors and cables and avoid unnecessary exposure to adverse conditions.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Check before use and after changes. Protective devices do not authorise use of damaged equipment.
How can a temporary supply become unsafe as a site changes?
Temporary supplies can change rapidly and cross transport or public routes. Informal additions can undermine the design. See Electricity at work: Safe working practices and Maintaining portable electrical equipment.
An event supply, refurbishment area or changing worksite can acquire new circuits, extensions and crossing routes as activities develop. Cable damage, unsuitable loading and public access can accumulate even if the first installation was suitable. Dismantling and storage can also introduce defects for the next job.
Which source controls and checks change the outcome?
Reduce temporary supply needs through layout and suitable equipment selection; have competent people design and verify the supply, distribution, cable protection and conditions of use. The coordinator controls additions and checks routes after each change. Include access, weather and emergency arrangements. Stop on unauthorised modification, visible damage or loading uncertainty; cable covers and a test label do not replace competent design and control of the live installation.
How should the controls be applied?
Plan distribution, protection, routing and responsibility; coordinate with other work and control alterations.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Keep design and inspection handovers and assess safe shutdown during loss of supply.
How do overhead lines, buried services, static and lightning differ?
Plant can contact lines or buried services. Static ignition and lightning are distinct mechanisms, not ordinary appliance faults. See Avoiding danger from overhead power lines and Avoiding danger from underground services.
A crane or delivery boom approaches an overhead line, an excavation reaches a buried cable, and fuel transfer creates a potential static ignition source. These are different harm pathways; a weather warning introduces another external energy source. A guessed clearance or one common PPE item cannot control them all.
Which source controls and checks change the outcome?
Avoid the interface by route or work redesign, then obtain competent utility information and source-specific separation or isolation arrangements. Static and lightning protection require their own competent design. The supervisor verifies boundaries, equipment reach and changed conditions; untrained people do not measure an assumed safe distance by approaching the source. Stop when service identity, location or agreed protection is uncertain, and use the relevant utility and emergency arrangements.
How should the controls be applied?
Coordinate service interfaces with competent people and owners; use Dangerous Substances and Explosive Atmospheres Regulations (DSEAR) for static ignition and site weather response for lightning.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Plans alone do not establish a cable position or safe condition. Do not invent clearances or lightning protection designs.
How should this hazard group be assessed and managed in practice?
For portable tools and planned maintenance, identify supply arrangements, access to conductors, wet conditions, temporary wiring, overhead lines and who is authorised to isolate and work on the system. Select suitable equipment, protect cables and maintain systems according to risk. Plan work dead wherever possible and use competent electrical personnel for isolation and verification. Restrict access and manage overhead line interfaces. Electrical asset register; risk based inspection and maintenance schedule; defect quarantine; competence records; isolation planning; contractor coordination and temporary supply checks. Follow the assessment through procurement, implementation, briefing, supervision and verification rather than stopping at a document. See Electricity at work: Safe working practices and Maintaining portable electrical equipment.
Agree the activity, affected people and prerequisites with operations, workers and any contractor before work. Test whether the task can be removed or redesigned, then verify selected controls in the place they will operate. During work, the supervisor compares conditions with the assessed method and has authority to stop. Completion includes safe waste or equipment handling, outstanding defects and a named hand-back decision; a completed risk form is not the end of the control process.
What must be established before assigning a risk score?
Identify the actual activity, foreseeable harm, people exposed and controls already demonstrated to work. Consider start up, normal operation, cleaning, maintenance, breakdown, emergency response and simultaneous work. A numerical matrix may support prioritisation but cannot establish compliance or replace a specialist assessment. Do not assign a residual risk score merely because a proposed control has been written into a form. Keep unknowns explicit and obtain site evidence before deciding that work can proceed. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Write a short causal description: the work creates or releases something, a person is exposed by a particular route, and a specified injury or ill-health outcome is foreseeable. Establish whether existing measures work in the actual task before estimating likelihood. An unknown material, unverified safe state or absent critical control is a decision gap, not a reason to select a reassuring number. The responsible manager records what must be resolved and who can authorise the next step.
Who owns each control and how should it be verified?
The dutyholder provides resources and arrangements. The operational manager assigns each control to someone able to implement it. Supervisors verify the controls at the point of work and respond to defects. Workers and representatives explain work as done and report problems. Specialist advisers address limits of local competence. Record the control, responsible role, evidence, check method, due date and escalation route. Completion of a training course or signature alone does not demonstrate effective risk control. See Managing for health and safety (HSG65).
Separate the person who funds and owns the control from the person who performs its check. For an engineered measure, record the accepted performance or condition, who verifies it, what a failed result means and how maintenance is coordinated. For a staffing or organisational measure, check actual cover, authority and staff experience. A signature confirms a recorded action, not effectiveness. The supervisor must be able to hold work and obtain a competent remedy when the required condition is not met.
Who might be affected, including people outside the work team?
Include employees, agency workers, apprentices, contractors, cleaners, maintainers, delivery drivers, service users, visitors and nearby public. Consider inexperience, pregnancy, disability, health conditions, language needs and lone work individually and without stereotyping. Consultation should identify barriers to controls rather than collect unnecessary medical details. Share relevant interface information between employers. A single activity may require several hazard groups; avoid splitting the assessment so that interacting controls have no clear owner. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Walk through the job from the perspective of someone who has not received the operator briefing: a cleaner, visiting driver, contractor, new starter or occupant of an adjoining area. Ask whether a control protects them during arrival, normal work, waste removal and emergencies. Agree who controls each shared boundary and how changes are communicated. Individual needs influence a suitable arrangement but do not justify treating an employee, disability or health condition as the hazard.
When should the assessment be reviewed and what evidence matters?
Reassess when equipment, materials, staffing, layout, working hours or environmental conditions change; after incidents, near misses, complaints, symptoms or evidence of failed controls; and through planned risk based review. Verify improvements under realistic demand, not only during an announced inspection. Retain dated observations, measurements where relevant, maintenance records and action closure evidence. No single review interval suits every risk. Health surveillance, exposure monitoring and clinical diagnosis are different activities and require their own competent arrangements. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Use a change or failure to test the original assumptions, not merely change the date on the form. A different product, higher throughput, altered route, new shift or contractor may change the harm pathway. Keep observations, applicable measurements, defects and authorisation evidence linked to the task. After correction, verify under representative demand and with affected workers. Repeated workarounds or symptoms require investigation of the design and organisation, even when no injury has been recorded.
How could electrical hazards arise in construction and civil engineering?
In construction and civil engineering, excavation approaches buried electricity. Plan service identification and controlled work. Service locating records. This is an illustrative application, not a documented case or a complete method statement. See Avoiding danger from underground services.
Sequence the job with adjacent trades, delivery routes and the changing work area; the contractor supervisor must check the actual stage before releasing work. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could electrical hazards arise in manufacturing and engineering?
In manufacturing and engineering, maintenance opens an electrical cabinet. Plan competent work dead and access restriction. Isolation evidence. This is an illustrative application, not a documented case or a complete method statement. See Electricity at work: Safe working practices.
Include startup, product change, cleaning and maintenance as well as the normal cycle; the production supervisor and maintainer agree who can stop and hand back the equipment. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could electrical hazards arise in warehousing and logistics?
In warehousing and logistics, warehouse traffic crushes charger cables. Protect routes and quarantine defects. Inspection and repair records. This is an illustrative application, not a documented case or a complete method statement. See Maintaining portable electrical equipment.
Assess peak demand, vehicles, loads and visiting drivers together; the shift manager verifies separation and handling arrangements before releasing the route. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could electrical hazards arise in agriculture and forestry?
In agriculture and forestry, farm machinery approaches overhead lines. Avoid the interface and coordinate with the owner. Route plan and briefing. This is an illustrative application, not a documented case or a complete method statement. See Avoiding danger from overhead power lines.
Consider seasonal work, lone locations, animals, terrain and access to help; the task manager verifies the method and communication before the crew starts. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could electrical hazards arise in hospitality and food production?
In hospitality and food production, kitchen cleaning introduces water around appliances. Coordinate cleaning and safe equipment use. Cleaning handover. This is an illustrative application, not a documented case or a complete method statement. See Electrical safety and you: A brief guide.
Check food operations, cleaning, public access and busy service periods together; the kitchen or service supervisor must be able to interrupt the task without leaving another exposure uncontrolled. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could electrical hazards arise in retail and public services?
In retail and public services, retail teams add seasonal electrical loads. Obtain competent supply assessment. Installation change records. This is an illustrative application, not a documented case or a complete method statement. See Electricity at work: Safe working practices.
Include customers, visitors and staff who arrive without the task briefing; the premises manager verifies access and a safe service alternative before the activity starts. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could electrical hazards arise in offices and professional services?
In offices and professional services, office workers use damaged chargers. Provide reporting and replacement. User checks and quarantine. This is an illustrative application, not a documented case or a complete method statement. See Maintaining portable electrical equipment.
Include contractors, hybrid working and occupied-space interfaces; the facilities or team manager checks the actual setup and how problems are reported. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could electrical hazards arise in education and laboratories?
In education and laboratories, laboratories operate high energy test equipment. Restrict access and obtain competent task assessment. Authorised procedures. This is an illustrative application, not a documented case or a complete method statement. See Electricity at work: Safe working practices.
Separate learner awareness from authorised operation and specialist intervention; the responsible teacher, technician or laboratory manager checks material identity and supervision. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could electrical hazards arise in utilities and waste management?
In utilities and waste management, utilities recover flooded assets. Restrict access until competent assessment. Recovery and isolation evidence. This is an illustrative application, not a documented case or a complete method statement. See Electricity at work: Safe working practices and Business flood plan checklists.
Plan for unknown material, remote access and interfaces with the public or other operators; the supervisor holds the job until necessary identification and control evidence is available. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could electrical hazards arise in energy and process industries?
In energy and process industries, process operators transfer flammable liquid. Assess static ignition through DSEAR. Engineering control checks. This is an illustrative application, not a documented case or a complete method statement. See Dangerous substances and explosive atmospheres.
Manage plant state, material change, connected systems and maintenance through competent process arrangements; the shift authority checks prerequisites and controls hand-back. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could electrical hazards arise in events and transport operations?
In events and transport operations, events deploy temporary outdoor power. Plan distribution and weather response. Handover and alteration records. This is an illustrative application, not a documented case or a complete method statement. See Electricity at work: Safe working practices and UK weather warnings.
Consider temporary equipment, weather, crowds, routes and limited setup time; the coordinator verifies the current layout and a workable stop or closure route. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How do you put the controls into practice?
Working dead and the GB live-work test
Where danger may arise from work on or near exposed live conductors, Electricity at Work Regulations 1989 regulation 14 requires all three conditions: it is unreasonable in the circumstances to make them dead; live work is reasonable in the circumstances; and suitable precautions prevent injury. Otherwise work dead. Production convenience alone is insufficient. This is a legal decision boundary, not a live-working method. Northern Ireland has its separate Electricity at Work Regulations (NI) 1991.
Electricity at Work Regulations 1989: regulation 14 · Electricity at Work Regulations (NI) 1991
Move from recognising harm to deciding, implementing, checking and improving the controls. Give each critical control an owner, a check method and a clear escalation route. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
- Understand the taskObserve people, equipment, materials and interfaces.
- Describe the harmIdentify exposure, energy release and foreseeable failure.
- Control at sourceAvoid, redesign, substitute, contain or separate the hazard.
- Check in real workVerify performance, defects, ownership and change triggers.
| Stage | Action | Who acts | Evidence to retain |
|---|---|---|---|
| Before work | Confirm the actual task, people, equipment, substances, location and abnormal conditions. | Operational manager with competent advice | Assessment, observations, consultation and required specialist checks |
| Control delivery | Select suitable equipment, protect cables and maintain systems according to risk. Plan work dead wherever possible and use competent electrical personnel for isolation and verification. Restrict access and manage overhead line interfaces. | Responsible manager and authorised implementers | Electrical asset register; risk based inspection and maintenance schedule; defect quarantine; competence records; isolation planning; contractor coordination and temporary supply checks. |
| During work | Supervise the real activity; check that critical controls remain effective and workers can report problems. | Supervisor and workers | Checks, defects, changes and escalations |
| Stop and restart | Stop the affected activity when serious danger or a failed critical control is suspected. Restart only through the competent site authorisation arrangements. | Supervisor and authorised competent person | Reason for stopping, corrective action, verification and restart authority |
| Review | Revisit controls after change, incidents, near misses, symptoms or repeated defects. Check effectiveness rather than counting completed forms. | Manager, Occupational safety and health (OSH) adviser and worker representatives | Dated review, closure evidence and lessons for design and procurement |
How does ERICPD apply to electrical hazards?
ERICPD stands for Eliminate, Reduce, Isolate, Control, PPE and Discipline. For electrical hazards, start by removing the hazardous task or source where practicable, then reduce and separate the remaining exposure. Combine suitable safeguards and work arrangements, use relevant personal protective equipment for residual risks, and keep all selected measures effective in everyday work. See HSE: Managing risk using PPE and Managing for health and safety (HSG65).
- 1 · E Eliminate
Remove the hazardous task or source where practicable; confirm that the alternative still fulfils the task and assess remaining hazards.
- 2 · R Reduce
Use a suitable less hazardous material, process or equipment, or reduce the hazard at source. Check any new risks introduced.
- 3 · I Isolate
Separate people from the hazard through suitable containment, guarding, barriers or other task-specific separation.
- 4 · C Control
Put remaining safeguards and workable task arrangements in place. Engineering controls and administrative arrangements have different strengths.
- 5 · P PPE
Select personal protective equipment for relevant residual exposure. Check suitability, fit, compatibility, use and maintenance.
- 6 · D Discipline
Sustain the controls through management support, supervision, maintenance and learning. Resolve workarounds and failures without blaming workers.
Eliminate, Reduce and Isolate focus attention on the hazard and the exposure pathway before reliance on behaviour or PPE. Controls usually work together: an enclosure may still need safe access, maintenance and instruction. Record the reasons for choosing or rejecting stronger options and check the complete task, including cleaning, maintenance and foreseeable changes.
ERICPD is a practical learning mnemonic. The five-level hierarchy is elimination, substitution, engineering controls, administrative controls and PPE. Reduce may include substitution or source reduction; Isolate commonly involves engineering. Control can include engineering and administrative measures. Discipline supports every selected level and is not an additional protective barrier. These frameworks are related; their labels do not form identical statutory ladders.
What does each role need to know and demonstrate?
People need learning and demonstrated competence for the decisions they actually make, not the same course at every organisational level. See Electricity at work: Safe working practices and Maintaining portable electrical equipment.
For electrical hazards, frontline learning must enable staff to recognise visible damage and stop using suspect equipment. Supervisors need to control supply changes, equipment condition and authorised access. Design, procurement and specialist assessment require deeper competence in competent installation design, safe isolation and risk-based maintenance. Awareness, supervised practice, assessment and authorisation are different stages; an attendance record alone does not establish competence or permit specialist intervention.
Assess practical understanding with the actual task and credible abnormal conditions. The assessor must be competent for the scope being tested; authorisation should state its boundaries. Reassess after a material change, a defect, a demonstrated gap or work outside that scope rather than assuming one fixed refresher interval suits every role.
| Role | Learning and decisions | Assessment, evidence and reassessment |
|---|---|---|
| Nearby staff and new starters | Recognise the relevant exposure, usable routes, warning signs and reporting or emergency arrangements. | Supervisor checks a practical explanation and scenario response; retain briefing scope and gaps. Repeat when routes or conditions change. |
| Frontline users | Demonstrate how to recognise visible damage and stop using suspect equipment, including the checks, limits and stop decision. | Competent task assessor observes representative practice and a defect scenario; record task, equipment/material scope and authorisation. Reassess for changed methods or performance gaps. |
| Specialist workers and maintainers | Demonstrate the applicable technical method, safe state, interface controls and hand-back; do not infer specialist skill from general awareness. | Competent specialist assesses work within a defined scope; retain method, assessment and authorisation evidence. New equipment, material or fault type may need a new decision. |
| Supervisors and coordinators | Demonstrate how to control supply changes, equipment condition and authorised access, manage a changed condition and hold or release work. | Manager or competent reviewer tests a realistic planning and stop/restart scenario; retain observed decisions and corrective actions. Review following interface failures. |
| Managers, purchasers and designers | Make and resource decisions on competent installation design, safe isolation and risk-based maintenance, including the stronger-control options and residual risks. | Competent review of specifications, trials, procurement acceptance and effectiveness evidence; record decision owner and outstanding actions. Reassess after process or organisational change. |
| OSH advisers, technical specialists and auditors | Distinguish jurisdiction and source limits, test representative evidence and recognise the boundary of their competence. | Appropriately competent review of the actual assessment, sources, sampling and closed actions; retain scope and limitations. Escalate missing technical information rather than inventing a conclusion. |
How can the hierarchy of controls reduce shock, arc-flash and electrical fire risks?
Maintenance is proposed on equipment connected to an electrical supply while neighbouring services remain in use. Shock, burns and unexpected movement are possible. Authorised competent people must establish the task-specific safe conditions and interfaces.
Illustrative SHARE example: assess stronger options first, then combine the measures needed for the remaining task. If elimination removes the task entirely, later measures address only remaining or different hazards. Each stage below explains what changes, how harm is reduced and who verifies it.
Applying ERICPD to other hazards in this group
For portable tools, temporary supplies and damaged cables, choose equipment and protection for the environment, control access and remove suspect equipment from use. A test label alone does not establish present suitability. This example is not a live-working or isolation procedure.
Keep an assessment record of the chosen controls, reasons for the selection, action owner, verification evidence and failure response. A failed critical control requires the affected activity to be held and corrected through the competent site arrangements; PPE or a completed form does not override that decision.
How should an outdoor temporary supply be reviewed after heavy rain?
Manage this activity by preventing exposure at source, coordinating the affected people and verifying the planned controls before release. An event team notices water near temporary distribution equipment after rain. Staff, contractors and the public can encounter shock, burns, fire or a secondary fall. A previous equipment test does not establish that the current installation and connectors are suitable or undamaged. See Maintaining portable electrical equipment and Electricity at work: Safe working practices.
Illustrative SHARE workplace example
What must be agreed before work starts?
The event manager restricts affected access and stops use through the planned safe arrangements, then obtains the authorised electrical person's decision. Before operation, competent people had specified the supply, equipment, protection, routes and weather assumptions. Review those assumptions against actual conditions; moving equipment or adding covers without competent assessment can leave the fault unresolved.
What changes, stops or hand-back decisions matter?
Inspection, isolation, repair and release remain within the authorised person's scope. Users must not open wet equipment, reconnect it or carry out a live investigation. The coordinator records the changed condition and maintains separation while safe alternatives are arranged. Reopen only after the competent verification and site access checks, documenting what changed and who authorised use. No specific voltage, protection rating or inspection interval is invented by this example.
How should jurisdiction, local rules and management assurance be handled?
Apply the law and regulator guidance for the work location, then use competent task and equipment information to establish the practical arrangements. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Health and Safety Executive (HSE) guidance generally addresses Great Britain; Northern Ireland has its own instruments and Health and Safety Executive for Northern Ireland (HSENI) route. Construction, dangerous substances, equipment and other specialist topics need the applicable instrument, not a Great Britain (GB) duty copied into a Northern Ireland (NI) answer. Fire arrangements also differ across the United Kingdom (UK) nations. Foreign project examples require destination-specific official advice and competent local assessment.
Distinguish a legal duty, regulator guidance, an organisation's rule and an illustrative SHARE method. A management system can link assessment, procurement, competence, maintenance, consultation and corrective action; a certification label or an unverified standard clause does not authorise work. For this group, sample evidence on competent installation design, safe isolation and risk-based maintenance and compare the recorded method with the activity observed on site. Resolve conflicts or missing technical information with the responsible competent person.
How would controlling portable tools on a changing site work in practice?
Maintenance staff use portable electrical tools where cables, access and moisture conditions change. Damaged insulation or unsuitable equipment can expose workers to shock or burns, with a possible secondary fall. The manager considers whether the task can avoid electrical equipment or use a more suitable system, with competent advice on its own risks. See Maintaining portable electrical equipment and Electrical safety and you: A brief guide.
Illustrative SHARE workplace example
What is required before and during the activity?
Before work, confirm equipment suitability, the supply arrangement and risk-based maintenance. Users check for visible damage within their competence and know how to report and remove defective equipment from use. During work, protect the cable route and reassess changed or wet conditions. Stop using equipment when damage, abnormal operation or an unsuitable supply is suspected; do not attempt an unauthorised repair or live investigation.
What does safe completion and hand-back require?
A competent authorised person decides on repair, inspection and return to service. Retain defect, maintenance and release records. A test label alone does not establish suitability for the present task. Laboratories, offices and outdoor events require different equipment and supply assessments.
Acronyms and terms
These terms distinguish the source of harm, the exposure route and the controls needed for the actual work.
| Letters or term | Expansion or definition | Meaning in this topic |
|---|---|---|
| UK | United Kingdom | A geographical description, not one identical set of health-and-safety instruments. |
| GB | Great Britain | England, Scotland and Wales; HSE guidance is generally framed for this jurisdiction. |
| NI | Northern Ireland | A separate health-and-safety legal route overseen by HSENI. |
| HSE | Health and Safety Executive | The GB regulator and a publisher of official workplace guidance. |
| HSENI | Health and Safety Executive for Northern Ireland | The NI regulator; check its applicable requirements and advice. |
| OSH | Occupational safety and health | Preventing work-related injury and ill health. |
| PPE | Personal protective equipment | Equipment worn for remaining exposure; it does not replace stronger source controls. |
| Control of Substances Hazardous to Health (COSHH) | Control of Substances Hazardous to Health | The GB hazardous-substance assessment and exposure-control route. |
| DSEAR | Dangerous Substances and Explosive Atmospheres Regulations | The GB route for relevant dangerous-substance fire, explosion and other safety risks. |
| PAT | Portable appliance testing | A commonly used term for testing portable equipment; a label does not prove current suitability. |
| ERICPD | Eliminate, Reduce, Isolate, Control, PPE, Discipline | A learning mnemonic for selecting and sustaining controls; not a statutory ladder. |
| Hazard | A source or condition with potential for harm | Describe what creates harm, rather than calling a person the hazard. |
| Exposure | A route or contact connecting source and person | Consider dose, duration and circumstances where relevant. |
| Critical control | A measure essential to the safe arrangement | Define its required condition, check, owner and failure response. |
| Hand-back | Controlled return to operation or use | Confirm people, equipment, protection and outstanding conditions before release. |
Example handy documents
Useful records connect the actual task to control ownership, checks, stop decisions and verified hand-back. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
The following are examples of documents an organisation could create or adapt, not downloadable files or a complete safe system. Use the task-specific information and competent review before applying them. Keep private health information outside general operational records.
What should a task and harm-route assessment contain?
Record people, source, exposure or energy, foreseeable harm, existing controls, stronger options, residual uncertainty and the responsible decision owner.
What should a critical-control check and defect log contain?
Record the required condition, check method, responsible person, failed result, restricted work and verified corrective action.
What should a change and hand-back record contain?
Capture changed material, equipment, staffing, layout or conditions; prerequisites, hold decisions, competent verification and restart authority.
What should a competence and authorisation record contain?
Name the assessed task and scope, practical evidence, assessor, limits, supervision and reassessment triggers.
What should an operational learning review contain?
Link observations, complaints, near misses or relevant exposure evidence to a design or organisational change and an effectiveness check.