SHARE Knowledge Hub
Maintenance, inspection and testing of work equipment and machinery
Maintenance keeps equipment in safe condition, inspection finds defects or deterioration, and testing checks a specified function. Choose each check for the actual equipment and hazard; statutory examination is a separate requirement only where the relevant law applies.
Owner: SHARE Knowledge Hub editorial team.
Understanding Maintenance, inspection and testing of work equipment and machinery
Maintenance keeps equipment in safe condition, inspection finds defects or deterioration, and testing checks a specified function. Choose each check for the actual equipment and hazard; statutory examination is a separate requirement only where the relevant law applies.
Why this matters at work
Operators are well placed to spot damage, leaks, loose guards, defective brakes, unusual sounds or control faults before a machine is used. Make the check relevant and short enough to perform; a long tick-box list that misses the fatal hazard is weak assurance. Teach what a failed check means and where to report it.
Plan tasks against the failure modes that matter: lubrication, wear, alignment, structural deterioration, hydraulic leakage, control drift and safeguard failure. State task, interval or condition trigger, competent role, access and isolation, pass/fail criteria, required record and response. Manufacturer guidance is a starting point, not a substitute for the site risk assessment.
How organisations manage this in practice
Record location, reason, authorisation, start, expiry, affected workers and shift handover. Control the physical or software bypass so it cannot be forgotten, and review cumulative impairments. A temporary fix after impact or alteration may trigger an exceptional inspection or examination.
A machine may remain mechanically operational while extraction or enclosure fails, exposing people to dust, fume or mist. Maintain ducts, hoods, filters, alarms and fans, inspect capture at the point of emission and follow the applicable COSHH examination and testing regime where a control measure requires it.
Ownership does not settle who must provide safe work equipment. The employer using hired equipment should check suitability, instructions, condition and relevant inspection or thorough-examination evidence; the hirer and supplier may each have responsibilities according to control. Agree who repairs defects and how equipment is quarantined while on site.
Control software or replacement parts through change review. A spare switch that fits physically may have a different function or defeat resistance. Record test method, as-found failure, adjustment, as-left result and any part of the function not covered.
Use appropriate specialist guidance for chainsaws, agricultural machinery, stump grinders or printing equipment where relevant. Not every equipment-specific leaflet applies to every workplace; select sources by actual machine and task. Conditions such as dust, outdoor use and vibration may make deterioration faster than in a controlled factory.
Distinguish the check from the assurance it provides
On a lift truck, a user check, maintenance, a functional test and a required thorough examination have different purposes. A service sticker cannot stand for all of them.

Identify the check
Match the equipment identity and actual parts/functions to the relevant user checks and planned inspection.
Repair and verify
Give defects an appropriate restriction, competent correction and evidence of restored function.
Keep assurance distinct
Check applicable inspection/testing and statutory examination requirements separately, including their scope and limitations.
Do not infer a universal interval or examination requirement from the illustrated truck alone.

Machinery guarding: trace the energy to the harm
Explore the working zone, guards, interlock, transmission, controls and energy isolator. Compare production work, cleaning and maintenance without treating a stopped machine as safely isolated.
Checksheets and risk assessments
Risk assessment forms
Risk assessment examples
Forms and tools
Full written walkthrough — all 8 steps
1. Identify the dangerous movement
What is happening: The cutaway exposes the workholding and cutter so you can inspect where contact could occur. It does not open or enable the real machine.
How harm can occur: A cutter can sever tissue; rotating parts can wind in hair or clothing; moving workholding can crush a hand.
Best practice to apply: Identify the task, all exposed people and the machinery’s intended operating limits. Keep the actual danger zone inaccessible.
2. Inspect the enclosure and access
What is happening: Inspect the enclosure, viewing panel and access edges. The visual cutaway changes only the drawing.
How harm can occur: A missing, damaged or unsuitable guard may allow reach into dangerous movement or fail to contain an ejected item.
Best practice to apply: Check the actual guard, fixing, condition and suitability. Do not infer reach distances or containment performance from this model.
3. Understand an interlock’s role
What is happening: The access interlock is a separate protective function. Its presence does not establish the reliability or stopping performance of the actual system.
How harm can occur: Defeating an interlock can permit access while hazardous movement is possible. Run-down may continue after a stop request.
Best practice to apply: Verify required protective functions through competent assessment and maintenance. Do not bypass them or use the cutaway as a working configuration.
4. Find the transmission hazards
What is happening: Inspect the drive and the cover around it. Dangerous movement can exist beyond the obvious working point.
How harm can occur: Belts, pulleys and rotating shafts can entangle, draw in or trap people during production or servicing.
Best practice to apply: Keep appropriate transmission guarding in place. Plan access and maintenance with the equipment information and actual energy sources.
5. Separate control stops from isolation
What is happening: The control panel and emergency stop act through control functions. The energy isolator is physically separate.
How harm can occur: A stopped display may conceal live energy or allow an unexpected restart; an emergency stop does not remove every energy source.
Best practice to apply: Use the required stop arrangements for operation and the actual safe isolation procedure for intrusive access.
6. Control hazardous energy for access
What is happening: Locate the separate isolator and the points where electrical, pneumatic, hydraulic, gravitational or mechanical energy may remain.
How harm can occur: Unexpected energisation, stored pressure or a falling component can cause shock, crushing or impact.
Best practice to apply: Identify, isolate, secure and verify the relevant energies using competent task-specific arrangements. The pictured lock is not proof that a machine is safe.
7. Plan cleaning and material handling
What is happening: Consider how material is loaded, held, removed and cleaned without bringing a person into danger.
How harm can occur: An inadequately held item can be ejected; reaching to clear swarf or a blockage can expose hands and clothing.
Best practice to apply: Use suitable workholding and handling methods. Stop and follow the safe system when a blockage or abnormal condition occurs.
8. Protect the people around the machine
What is happening: The operator’s work position and surrounding access affect people other than the person at the controls.
How harm can occur: Visitors, cleaners and nearby trades may enter a danger area or be struck by an ejected item.
Best practice to apply: Check layout, access, instruction, competence and supervision. Review the machine after changes and before returning it to service.
Illustrative awareness learning. The model does not design equipment, authorise work, verify safe conditions or complete a real inspection.
The wider workplace has its own account and subscription access. Exploring this lesson does not grant access, record course completion or authorise work.
How can I practise this topic in 3D?

A fan repair starts without a handover

Damaged slings and an unclear examination record
All related inspection points 5 across 2 locations
Garage workshop 3 inspection points
Construction site 2 inspection points
Practice in the SHAREhub environment. Browser practice is separate from workplace competence and formal learning records.
How do maintenance, inspection and testing differ?
Maintenance keeps equipment in safe condition; inspection finds dangerous condition or deterioration; testing challenges a specified function. Statutory thorough examination or written-scheme examination applies only to equipment within the relevant specialist regime.
Five activities with different evidence
Read the complete visual as text
- User check: A trained user looks for the defined visible or functional condition before use. Failure triggers the defect route; a pre-use check is not a statutory examination.
- Inspection and functional test: A competent inspection addresses installation or deterioration risks and exceptional events. A functional test proves a specified response against objective acceptance criteria.
- Maintenance and statutory examination: Maintenance preserves or restores condition. A specific legal regime may also require examination or testing by the appropriate competent person. Keep their scopes and records distinct.
Which check inspection test or examination is needed?
2 linked parts. Follow the question numbers and complete the applicable route.
Part 1 of 2 · Questions 1–3
Continue · Part 2 of 2 · Questions 4–5
Read the complete visual as text
- Start: Equipment is about to be used, introduced, moved, maintained, changed or returned to service.
- Question 1: Is there an obvious dangerous defect, abnormal state or immediate danger? Decision owner: Supervisor and competent machinery engineer.
- YES — EMERGENCY: Stop use, make safe and quarantine; obtain emergency help where needed before selecting routine checks. Owner: Supervisor and competent machinery engineer. STOP / REFER → APPROPRIATE RESPONSE.
- NO: Continue the remaining checks; this does not release the task. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 2.
- UNKNOWN — PROTECT FIRST: Keep people protected and obtain competent defect assessment; no use while dangerous state is uncertain. Owner: Supervisor and competent machinery engineer. STOP / REFER → APPROPRIATE RESPONSE.
- Question 2: Is a trained-user pre-use check required? Decision owner: Supervisor and competent machinery engineer.
- YES: Complete the defined check. A failed check holds use and goes to defect correction. Continue identifying other required activities. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 3.
- NO: Continue identifying installation, deterioration and specific-regime requirements. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 3.
- UNKNOWN — HOLD: The equipment owner establishes the required user check. Owner: Supervisor and competent machinery engineer. HOLD → REPEAT QUESTION 2 AFTER CORRECTION.
- Question 3: Is installation-dependent safety, dangerous deterioration or an exceptional event relevant? Decision owner: Supervisor and competent machinery engineer.
- YES: Define a competent PUWER inspection with equipment-specific scope and timing. Other applicable activities remain separate. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 4.
- NO: Record the inspection scope basis and continue the hidden-function check. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 4.
- UNKNOWN — HOLD: The competent equipment owner resolves the inspection trigger and scope. Owner: Supervisor and competent machinery engineer. HOLD → REPEAT QUESTION 3 AFTER CORRECTION.
- Question 4: Is a hidden safety function or post-repair condition unproved? Decision owner: Supervisor and competent machinery engineer.
- YES: Define a safe functional test, objective acceptance criteria and restoration. This does not replace other required examinations. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 5.
- NO: Continue the specialist-regime scope check. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 5.
- UNKNOWN — HOLD: Resolve the function and test evidence with the competent owner. Owner: Supervisor and competent machinery engineer. HOLD → REPEAT QUESTION 4 AFTER CORRECTION.
- Question 5: Does a specific regime require statutory examination or testing? Decision owner: Supervisor and competent machinery engineer.
- YES: Follow the applicable lifting, pressure, LEV, work-at-height or other competent-person route, alongside maintenance and checks. Record all required scopes. Owner: Supervisor and competent machinery engineer. OUTCOME → RECORD AND HAND OVER.
- NO: Record the scope basis and plan necessary maintenance and other identified activities. This classification is not permission to use. Owner: Supervisor and competent machinery engineer. OUTCOME → RECORD AND HAND OVER.
- UNKNOWN — HOLD: Obtain the competent legal/equipment scope decision before concluding the activity plan. Owner: Supervisor and competent machinery engineer. HOLD → REPEAT QUESTION 5 AFTER CORRECTION.
- Outcome: User check; PUWER inspection; functional test; statutory examination; maintenance; equipment held.
- Stop and escalation boundary: This learning route supplies no design value, operating setting, clinical diagnosis or site permission. The actual procedure, jurisdiction and competent local authority govern.
The Provision and Use of Work Equipment Regulations (PUWER), Lifting Operations and Lifting Equipment Regulations (LOLER) and Pressure Systems Safety Regulations (PSSR) each have distinct scope in GB and NI. A service sheet can show lubrication but not that an interlock stops a conveyor. A pre-use check can reveal an obvious damaged guard but does not replace a competent inspection where deterioration or installation creates significant risk. Lifting-equipment thorough examination and pressure-system written-scheme examination have different legal purposes and qualified examiners. HSE maintenance of work equipment, HSE inspection of work equipment, HSE LOLER overview and HSE pressure systems regulations overview.
| Activity | Purpose | What it does not prove |
|---|---|---|
| Pre-use check | User notices obvious damage or unsafe condition before use. | A simple visual check does not prove hidden safety functions; an instructed pre-use routine may include safe protected functional checks within the user’s competence. |
| Maintenance | Keeps or restores equipment to specification. | A completed service alone is not an independent condition inspection. |
| PUWER inspection | Competent check for installation or deterioration risk when triggered. | Not an automatic statutory thorough examination of every machine. |
| Functional test | Demonstrates a named guard, stop, brake, alarm or trip response. | A partial test does not validate an entire system. |
| LOLER thorough examination | Competent systematic examination of lifting equipment where applicable. | Does not replace routine maintenance or all PUWER checks. |
| PSSR written-scheme examination | Competent examination under a scheme for qualifying pressure systems. | Not the same as a generic service or LOLER report. |
Why does the distinction matter?
If the wrong check is chosen, a defect can remain hidden until a person meets moving machinery, a load falls or stored pressure is released.
A quarterly conveyor service might change a bearing but leave an interlock disconnected. A forklift service might overlook a lifting-chain defect requiring competent examination. A compressor may look tidy while its pressure safety device is unexamined under a written scheme. Work planning must trace each credible failure to the check that can detect it in time. HSE inspection of work equipment, HSE thorough examination of lifting equipment and HSE pressure systems regulations overview.
Which assets and functions need a plan?
List work equipment, its tasks, safety-critical parts, degradation mechanisms and required checks. Assign an owner for each inspection, maintenance task, test and defect.
For a conveyor, include guards, interlocks, emergency stops, drives, nip points and stored energy. For mobile plant, include brakes, tyres, steering, lift functions and attachments. For a pressure system, identify whether the system qualifies for a written scheme and its protected parts. Use the manufacturer’s information and the risk assessment to define what can deteriorate and who is competent to inspect it. HSE PUWER overview and HSE inspection of work equipment.
When is a PUWER inspection needed?
In Great Britain, inspection is required where safety depends on installation, where deterioration could cause danger, or after exceptional circumstances liable to jeopardise safety. The NI instrument is separate and must be checked for the NI workplace.
PUWER inspection triggers
Read the complete visual as text
- Installation-dependent safety: Inspect after installation and assembly where safety depends on those conditions, before use as required by the applicable route.
- Deterioration risk: Set the inspection scope and interval from the relevant parts, deterioration, duty, environment, manufacturer information and competent assessment.
- Exceptional event: Damage, significant change or another event that could jeopardise safety triggers a fresh decision. The calendar or an inspection sticker alone does not establish condition.
Set and review an interval
Read the complete visual as text
- 1. Legal or scheme route: Check whether a legal maximum, competent-person scheme or written scheme governs timing; do not exceed it through a generic risk ranking.
- 2. Mechanism and consequence: Define the safety-related part and the deterioration or failure mechanism to detect/prevent. Unknown basis holds interval selection.
- 3. Initial evidence: Use manufacturer information, duty, environment, installation, competence and relevant guidance to document a conservative starting basis.
- 4. As-found findings: Review failures, condition trends, inspection results and near misses. Deterioration can require a shorter or more intensive task before danger arises.
- 5. Stable evidence and events: Only competent review, where law permits and negligible deterioration is evidenced, may justify extension. Major change, damage, relocation or changed use can trigger inspection regardless of the calendar.
- 6. Record and recheck: The equipment owner records interval, scope, assumptions, authority and review triggers. No universal annual, six-month or twelve-month interval is created.
A reinstalled machine may need inspection before first use at the new location. Deteriorating equipment needs suitable intervals set by risk. Major modification, suspected serious damage or a substantial change of use can trigger an additional inspection. Not every item needs a formal inspection; a low-risk item may be adequately checked before use. Keep the inspection result and act on defects. HSE inspection of work equipment and HSENI PUWER 1999.
Inspection evidence follows the equipment
For GB PUWER inspection, retain the result at least until the next inspection and ensure equipment moving between undertakings has physical evidence of the last required inspection. Check scope, result, restrictions and next trigger before use. This is separate from LOLER/PSSR examination-record retention. NI uses its own PUWER route. HSE: inspection of work equipment.
How should intervals be set?
Choose an interval from failure consequence, environment, use, deterioration, manufacturer information and defect history. Do not apply one period to all work equipment.
A wet, abrasive or high-cycle setting can shorten the safe detection window. A safety function with hidden failure may need a protected functional test rather than a visual check. Adjust plans after repeat faults, near misses, modification or evidence that failures occur between checks. Specialist regimes may prescribe an examination scheme or interval for their scope; confirm the jurisdiction and equipment before quoting one. HSE inspection of work equipment and HSE thorough examination of lifting equipment.
How should a safety function be tested?
Specify the function, safe test position, expected response, acceptance criteria and restoration before a competent person tests it.
For an interlock, confirm the guard state, stopped or prevented motion, run-down and restart behaviour for the real access route. A green indicator alone is not proof. Test from a protected position and record failures; do not put a person in danger to demonstrate the function. After repair or modification, consider the whole linked system, not only the replaced component. HSE L22 Safe use of work equipment and HSE maintenance of work equipment.
How should defects be controlled?
Report and classify the defect, keep dangerous equipment out of use, repair competently and prove the affected function before release.
A missing guard, failed brake, cracked lifting part or uncertain pressure protection needs a clear stop-use decision. Tagging helps communicate a hold but does not physically prevent reuse on its own; choose isolation or access control as needed. Record who may remove the hold and what evidence they require. Repeated defects call for cause investigation and a changed plan. HSE maintenance of work equipment and HSE thorough examination of lifting equipment.
Separate a service defect from an examination report
An ordinary service defect is recorded, quarantined and resolved through the equipment system. A statutory examiner’s finding follows its own report route as well as the work restriction. For GB LOLER, the examiner immediately informs the dutyholder of dangerous defects; serious existing or potential dangerous defects require the prescribed written report and a copy to the enforcing authority as soon as practicable. Respect any specified remedy deadline and prohibition on continued use. HSE: lifting examinations and dangerous-defect reports.
For GB PSSR, the competent person’s imminent-danger process includes immediate notification, a written report to the user/owner and a copy to the enforcing authority within 14 days; prevent operation until the required remedy is made. HSE: pressure systems. NI has separate LOLER/PSSR instruments and enforcing routes: apply the corresponding current provisions and competent advice. A manager cannot waive an examiner’s restriction; not every minor maintenance defect is externally reportable.
How can maintenance itself be made safe?
Plan intervention hazards before removing guards or opening plant. Control energy, movement, height, substances, contractors and nearby operations for the whole job.
Identify every energy source, bring equipment to the required state, securely isolate, prevent reconnection and release or restrain stored energy. A stop command or open guard is not secure isolation. Use planned exceptional powered fault-finding only with competent specialists and designed protection. Coordinate group work and shift changes. HSE maintenance of work equipment and HSE L22 Safe use of work equipment.
At handback, account for people and tools, restore guards and devices, verify the affected functions and authorise a controlled restart. A permit is a coordination tool where the risk system requires it; it does not substitute for physical controls. Contractors need equipment identity, instructions, hazard information and a defined interface.
How can the hierarchy of controls reduce machinery risks during maintenance, inspection and testing?
Choose the safe intervention and test method before a maintainer approaches danger. Design out unnecessary access, use engineered separation and secure isolation for the planned work, then support those measures with competent instruction, controlled tests and residual PPE.
Illustrative decision: BuildOut replaces a conveyor bearing and checks the protective interlock. Mechanical repair and demonstration of the safety function are separate tasks. The engineer specifies the isolation and the protected test; the supervisor coordinates operators, cleaners and linked equipment.
ERICPD means Eliminate, Reduce (including substitution), Isolate, Control, PPE and Discipline. The five-level hierarchy groups measures as elimination, substitution, engineering controls, administrative controls and PPE. They overlap: isolation is usually an engineering measure; control can include engineered and administrative measures. Discipline means maintaining and checking the controls, supervising the method and learning from defects, rather than blaming someone or accepting weaker protection.
The comparison is an original illustrative application of the general HSE hierarchy, not a machine-specific method, permit or design approval. The employer must choose measures for the actual work and jurisdiction. Apply the separate Northern Ireland legal route where relevant; the local assessment and competent technical decision govern release.
How can a conveyor fail despite regular servicing?
BuildOut’s bearing service did not prove the interlock still worked. The supervisor must hold use until a competent repair and protected function test support named release.
Isolate, maintain, test and hand back
Read the complete visual as text
- Plan and make safe: Identify the equipment, task, connected plant and every energy source. Secure isolation and control stored energy by the approved method before hazardous access.
- Repair and restore: Use competent people and suitable parts. Reconcile assembly, settings, supports, guards, interlocks, tools and temporary items.
- Prove and transfer: Test the complete affected function safely, close triggered inspection or examination actions and brief the receiving operator. Named authority controls return to service.
Maintenance handback and return to service
2 linked parts. Follow the question numbers and complete the applicable route.
Part 1 of 2 · Questions 1–3
Continue · Part 2 of 2 · Questions 4–5
Read the complete visual as text
- Start: Maintenance or repair is reported complete.
- Question 1: Are parts, assembly, fasteners, fluids, supports, settings and temporary items reconciled? Decision owner: Supervisor and competent machinery engineer.
- YES: The named evidence is confirmed. Continue the next applicable check. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 2.
- NO / UNKNOWN — HOLD: The competent maintainer completes physical reinstatement; keep the safe state. Owner: Supervisor and competent machinery engineer. HOLD → REPEAT QUESTION 1 AFTER CORRECTION.
- Question 2: Are guards, interlocks, brakes, controls, alarms and affected functions restored? Decision owner: Supervisor and competent machinery engineer.
- YES: The named evidence is confirmed. Continue the next applicable check. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 3.
- NO / UNKNOWN — HOLD: Keep isolated or otherwise in the assessed safe state; correct the safeguard defect. Owner: Supervisor and competent machinery engineer. HOLD → REPEAT QUESTION 2 AFTER CORRECTION.
- Question 3: Has the complete function passed a safe test against defined criteria? Decision owner: Supervisor and competent machinery engineer.
- YES: The named evidence is confirmed. Continue the next applicable check. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 4.
- NO / UNKNOWN — HOLD: Do not release. Diagnose through the controlled method, repair and repeat affected tests. Owner: Supervisor and competent machinery engineer. HOLD → REPEAT QUESTION 3 AFTER CORRECTION.
- Question 4: Are triggered PUWER inspections and other statutory examination actions complete? Decision owner: Supervisor and competent machinery engineer.
- YES: The named evidence is confirmed. Continue the next applicable check. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 5.
- NO / UNKNOWN — HOLD: Keep equipment unavailable until the appropriate competent-person actions are satisfied. Owner: Supervisor and competent machinery engineer. HOLD → REPEAT QUESTION 4 AFTER CORRECTION.
- Question 5: Are records updated and limitations, monitoring and emergency actions communicated? Decision owner: Supervisor and competent machinery engineer.
- YES: The named operational authority accepts equipment and controls first use. A failed or abnormal response stops it again. Owner: Supervisor and competent machinery engineer. OUTCOME → RECORD AND HAND OVER.
- NO / UNKNOWN — HOLD: Complete the receiving-operator briefing and evidence transfer. Owner: Supervisor and competent machinery engineer. HOLD → REPEAT QUESTION 5 AFTER CORRECTION.
- Outcome: Physical hold; safeguard hold; test hold; statutory hold; briefing hold; controlled return; abnormal stop.
- Stop and escalation boundary: This learning route supplies no design value, operating setting, clinical diagnosis or site permission. The actual procedure, jurisdiction and competent local authority govern.
BuildOut service and failed interlock
Task material and setting: BuildOut Ltd’s warehouse conveyor moves bagged building material. A contractor services bearings, then an operator reports that the interlocked access guard no longer stops the belt.
People and prerequisites: Operator, cleaner, contractor and supervisor may enter the zone. The machine identity, linked drives, pneumatic feed, instructions and previous test result are needed.
Before: The operator stops and reports the failure; the supervisor holds the whole affected line. The maintainer identifies and verifies every energy boundary before opening the guard.
During: Competent repair investigates the interlock and service change. No production running or improvised powered test occurs while a person is exposed.
Hold or stop: Hold if guard function, isolation, run-down, linked restart or personnel accounting is uncertain. The completed service sheet is not a release.
Completion and hand back: Restore guards, clear tools and people, perform the specified protected stop/restart test, record the result and obtain named release.
Evidence: Keep defect and hold record, isolation method, repair, functional test, affected inspection decision, contractor handback and recurring-failure review.
What changes across equipment and sectors?
The check must fit the failure route: moving machinery, mobile lifting and stored pressure need different competence and legal scope.
| Equipment or setting | Failure route | Check and stop decision |
|---|---|---|
| Manufacturing conveyor | Guard or interlock fails; person reaches moving nip. | Protected functional test and repair; hold on failed stop. Sources: HSE maintenance of work equipment; HSE inspection of work equipment; HSE L22 Safe use of work equipment. |
| Warehouse lift truck | Brakes or steering fail; lifting chain or attachment deteriorates. | PUWER vehicle checks plus applicable LOLER thorough examination; hold dangerous defects. Sources: HSE inspection of work equipment; HSE LOLER overview; HSE thorough examination of lifting equipment. |
| Construction mobile elevating platform | Stability or lifting part deteriorates; person falls. | Machine-specific maintenance, pre-use checks and lifting examination where applicable. Sources: HSE LOLER overview; HSE thorough examination of lifting equipment; HSE maintenance of work equipment. |
| Process compressor | Pressure boundary or protective device fails. | Determine PSSR scope, written scheme and competent examination; no use outside safe limits. Sources: HSE pressure systems regulations overview; HSE maintenance of work equipment. |
Who owns each check and release?
Users perform defined pre-use checks; competent people inspect, maintain and test within scope; competent, sufficiently impartial people handle specialist statutory examinations; managers control defects and release.
One lift truck, separate evidence routes
Read the complete visual as text
- PUWER condition and use: Maintain the truck, provide suitable instruction and carry out relevant user checks and inspections. Examine brakes, tyres and other safety functions within the correct scope.
- LOLER lifting route: Apply thorough-examination and defect-reporting duties where LOLER scope is established. That examination does not cover every non-lifting hazard on the truck.
- Reconcile before use: A maintenance service, pre-use check and thorough examination cannot substitute for each other. Dangerous defects hold use until the appropriate correction and release evidence exists.
A supervisor should not sign a specialist examination they cannot judge. A competent examiner may be in-house if sufficiently independent and impartial; the person who routinely maintains the equipment should not examine their own work. The examiner must identify dangerous defects and act without pressure from the maintenance team. A manager needs one asset record that connects tasks, findings, holds, tests, statutory reports and authorisation. HSE thorough examination of lifting equipment and HSE inspection of work equipment.
What competence does each role need?
Teach and assess the task each person performs, define authority and reassess after equipment, method or performance changes.
| Role | What to learn | Practical proof | Assessor and record | Reassessment trigger |
|---|---|---|---|---|
| New worker | Recognise damaged guards, failed stop, tags and reporting. | Demonstrates a safe stop and defect report. | Supervisor records awareness. | New machine or incident. |
| Operator | Know pre-use check, normal limits and hold conditions. | Shows the actual check and refuses unsafe use. | Supervisor signs machine/task scope. | New mode, defect trend or changed task. |
| Maintainer | Know instructions, isolation, repair, protected test and handback. | Practical task and verified energy boundary. | Engineering lead records authorisation. | New energy, component or method. |
| Inspector or examiner | Know relevant damage modes and legal/scheme scope. | Examines representative defects and writes a usable report. | Competent technical lead and, where needed, impartiality review. | Equipment or regime change. |
| Supervisor or manager | Plan intervals, hold defects, coordinate contractors and release. | Runs failed-interlock scenario with written hold and evidence. | Responsible manager samples decisions. | Repeated defect or near miss. |
| Safety adviser or auditor | Trace GB/NI law and source to field evidence. | Samples check, repair, test and statutory report distinction. | Independent competent review. | Law or assurance finding. |
Which GB and NI legal routes apply?
Great Britain uses PUWER 1998, LOLER 1998 and PSSR 2000 where each applies; Northern Ireland has separate 1999 PUWER and LOLER instruments and PSSR 2004.
Territory and machinery-supply routes
Read the complete visual as text
- GB workplace use: Use the GB PUWER route and any relevant LOLER, pressure, COSHH, electrical or work-at-height requirements. Establish scope before choosing the statutory evidence.
- NI workplace use: Use NI PUWER and the applicable separate NI specialist regulations. Do not present a GB regulation as UK-wide.
- Product supply is separate: Destination, first placing date, product scope and economic-operator role govern the product-law route. Recheck the NI transition before 20 January 2027. Supply conformity does not replace workplace suitability.
Identify the workplace, equipment, intended function and whether lifting or a relevant pressure system is involved. Do not apply an examination interval from one regime to every machine. PUWER inspection, LOLER thorough examination and PSSR written-scheme examination are different duties with different evidence. HSE inspection of work equipment, HSE thorough examination of lifting equipment, HSE pressure systems regulations overview and HSENI work equipment and machinery guidance.
| Route | Relevant duty | Reader decision |
|---|---|---|
| GB PUWER 1998 | Maintenance and triggered work-equipment inspection. | Use HSE and current GB instrument for the asset. |
| NI PUWER 1999 | Separate NI work-equipment route. | Use HSENI and current NI instrument; do not cite GB regulation as NI law. |
| GB LOLER 1998 | Additional lifting-equipment duties and thorough examination where applicable. | A service is not a LOLER examination. |
| NI LOLER 1999 | Separate NI lifting-equipment route. | Confirm NI examination scope and competent person. |
| GB PSSR 2000 | Qualifying pressure systems need a written scheme and examination under it. | Confirm system scope and scheme before use. |
| NI PSSR 2004 | Separate NI pressure-system written-scheme and examination route. | Confirm current NI instrument and scheme for the system. |
How should managers assure equipment remains safe?
Trace each important failure to the check that detects it, then sample the evidence and the actual plant condition.
Review overdue checks by risk, failed functional tests, statutory reports, repeated defects, contractor quality and unauthorised returns. Walk the equipment with operators to find access and intervention realities. A dashboard showing 100% completed services is weak if it omits guards, emergency stops or pressure protection. HSE inspection of work equipment and HSE maintenance of work equipment.
A record that supports a release decision
Illustrative asset record: conveyor interlock; protected functional check under the machine-specific plan; competent engineer; last result failed; equipment held; next trigger after repair; release requires specified passing results, guards restored and named handback. A service closure is not proof of a required inspection or examination.
When must equipment be held or an emergency start?
Hold use for a failed safeguard, dangerous defect, overdue required examination, uncertain pressure condition or unverified isolation. Protect people before investigating records.
Defect quarantine and release
2 linked parts. Follow the question numbers and complete the applicable route.
Part 1 of 2 · Questions 1–3
Continue · Part 2 of 2 · Questions 4–5
Read the complete visual as text
- Start: A check, inspection, test, examination, alarm or user report identifies a defect or unexplained symptom.
- Question 1: Is there immediate danger or could danger develop before controlled action? Decision owner: Supervisor and competent machinery engineer.
- YES — EMERGENCY: Stop, make safe, quarantine and use the emergency route as required. Check statutory defect notifications separately. Owner: Supervisor and competent machinery engineer. STOP / REFER → APPROPRIATE RESPONSE.
- NO: Continue the remaining checks; this does not release the task. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 2.
- UNKNOWN — PROTECT FIRST: Protect people and keep equipment held while the competent owner establishes the safety consequence. Owner: Supervisor and competent machinery engineer. STOP / REFER → APPROPRIATE RESPONSE.
- Question 2: Are extent, consequence and applicable legal regime understood? Decision owner: Supervisor and competent machinery engineer.
- YES: The named evidence is confirmed. Continue the next applicable check. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 3.
- NO / UNKNOWN — HOLD: Keep held. Obtain competent defect assessment; repeated resets or a label are not evidence. Owner: Supervisor and competent machinery engineer. HOLD → REPEAT QUESTION 2 AFTER CORRECTION.
- Question 3: Can a competent repair restore the required specification? Decision owner: Supervisor and competent machinery engineer.
- YES: Control energy, repair, record parts/settings and test the complete affected function. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 5.
- NO: Assess whether any time-limited disposition is legally and technically supportable. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 4.
- UNKNOWN — HOLD: Keep out of service and obtain the technical repair/disposition basis. Owner: Supervisor and competent machinery engineer. HOLD → REPEAT QUESTION 3 AFTER CORRECTION.
- Question 4: Is time-limited use legally and technically supportable? Decision owner: Supervisor and competent machinery engineer.
- YES: Define actual limits, monitoring, owner, deadline and withdrawal trigger; then complete all statutory and hand-back checks. Owner: Supervisor and competent machinery engineer. CONTINUE → QUESTION 5.
- NO / UNKNOWN — HOLD: Keep out of service pending repair or disposal. No grace period is created. Owner: Supervisor and competent machinery engineer. HOLD → REPEAT QUESTION 4 AFTER CORRECTION.
- Question 5: Are statutory actions, functional tests, documents and named hand-back complete? Decision owner: Supervisor and competent machinery engineer.
- YES: The authorised owner records the exact released state and communicates limitations and monitoring. Owner: Supervisor and competent machinery engineer. OUTCOME → RECORD AND HAND OVER.
- NO / UNKNOWN — HOLD: Remain quarantined until the competent owners close the missing action. Owner: Supervisor and competent machinery engineer. HOLD → REPEAT QUESTION 5 AFTER CORRECTION.
- Outcome: Emergency stop; evidence hold; repaired and tested; controlled time-limited status; disposal; authorised release.
- Stop and escalation boundary: This learning route supplies no design value, operating setting, clinical diagnosis or site permission. The actual procedure, jurisdiction and competent local authority govern.
Stop from a safe place, prevent reuse, report and ask the competent owner for assessment. For injury, entrapment or release, raise the alarm and follow the site rescue or emergency plan; improvised movement can worsen harm. Resume only after correction, required examination or test, restored protection and named handback. HSE maintenance of work equipment and HSE thorough examination of lifting equipment.
What should fuel-equipment inspection and testing evidence identify?
Use the component view to identify the actual equipment and intended protection function. The planned record link describes expected evidence, not a completed check.

Inspection, integrity and evidence
A hose, tank or protective device has a safety purpose which depends on its condition and supporting checks.
Activity focus: Connect each identified defect to the responsible owner and appropriate operational decision.
Contextual workplace scene. Use the task, control and evidence checks in this section; appearance alone does not establish safe conditions, individual health or approval.

Dispenser internals and external surroundings
Compare the fixed dispenser island and cabinet with an inserted nozzle at the vehicle filler. The near and extended-hose positions show why the refuelling interface needs its own assessment location.
Activity focus: Use the cutaway for the dispenser internals, then follow the hose to the nozzle tip. Move the filler outward without stretching the hose and compare the stated Stage II recovery conditions.
Contextual workplace scene. Use the task, control and evidence checks in this section; appearance alone does not establish safe conditions, individual health or approval.
Educational illustration, not to scale. Coloured zones are teaching examples, not a site-specific hazardous-area classification.
What do the acronyms and key terms mean?
These terms separate maintenance, inspection, testing and specialist examination.
Definitions are grounded in HSE inspection of work equipment.
| Term | Full name | Meaning here |
|---|---|---|
| PUWER | Provision and Use of Work Equipment Regulations | GB 1998 and NI 1999 are separate workplace-use routes. |
| LOLER | Lifting Operations and Lifting Equipment Regulations | GB 1998 and NI 1999 are separate lifting-equipment routes. |
| PSSR | Pressure Systems Safety Regulations | GB 2000 and NI 2004 are separate pressure-system routes. |
| WSE | Written scheme of examination | Specifies competent examination of a qualifying pressure system. |
| ACOP | Approved Code of Practice | Guidance with distinct legal status. |
| PPE | Personal protective equipment | Residual protection, not a substitute for safe plant. |
| Functional test | Not an acronym | Demonstration that a named protection responds as specified. |
| Thorough examination | Not an acronym | Detailed competent examination where lifting law applies. |
| ERICPD | Eliminate, Reduce, Isolate, Control, PPE, Discipline | A control-selection aid; sustain controls through supervision, maintenance and learning. It creates no separate legal duty. |
Which Crownway Fuels documents support this topic?
Open an editable document, read the preview, or find its place in the Crownway hierarchy. 8 resources relate to this page.
Fictional Crownway Fuels examples for English forecourts, with a separate illustrative bulk terminal. Check site applicability, permissions and actual controls before adapting any document for use.
Maintenance inspection and safety critical reliability policy (8)
- Maintenance inspection and safety critical reliability policy (CWF-POL-MAINT · Completed fictional example)
Set company expectations, responsibilities and resources for maintenance inspection and safety critical reliability.
Read preview · Download DOCX · Show in hierarchy - Maintenance inspection and safety critical reliability procedure (CWF-PRO-MAINT · Completed fictional example)
Explain who does what, in what sequence, the control rationale, evidence, escalation and safe restart conditions.
Read preview · Download DOCX · Show in hierarchy - Plant criticality maintenance and examination register (CWF-REG-MAINT-01 · Blank register with separate fictional worked entries)
Provide the site/task-specific plant criticality maintenance and examination register and retain its controlled output.
Read preview · Download XLSX · Show in hierarchy - Safety critical maintenance and proof test schedule (CWF-PLN-MAINT-01 · Completed fictional example)
Provide the site/task-specific safety critical maintenance and proof test schedule and retain its controlled output.
Read preview · Download DOCX · Show in hierarchy - Preventive maintenance and functional test record (CWF-CHK-MAINT-01 · Blank editable master)
Provide the site/task-specific preventive maintenance and functional test record and retain its controlled output.
Read preview · Download DOCX · Download PDF · Show in hierarchy - Safety critical impairment and overdue task decision (CWF-FRM-MAINT-01 · Blank editable master)
Provide the site/task-specific safety critical impairment and overdue task decision and retain its controlled output.
Read preview · Download DOCX · Show in hierarchy - Pressure system and lifting examination applicability register (CWF-REG-MAINT-02 · Blank register with separate fictional worked entries)
Provide the site/task-specific pressure system and lifting examination applicability register and retain its controlled output.
Read preview · Download XLSX · Show in hierarchy - Maintenance quality and contractor handback check (CWF-CHK-MAINT-02 · Blank editable master)
Provide the site/task-specific maintenance quality and contractor handback check and retain its controlled output.
Read preview · Download DOCX · Download PDF · Show in hierarchy
Unlock another resource
You have used this month’s two free downloads. Publish a post in your own words to unlock one more resource, or choose SHARE Individual for 10 downloads per month.
You decide whether to share. If you do, use the relevant platform disclosure tools and do not make claims you do not genuinely hold.