SHARE Knowledge Hub
Hazard group - mechanical hazards
Mechanical hazards arise from moving machinery, tools, vehicles, loads or components and from the unexpected release of stored energy. People may be cut, crushed, trapped, entangled, struck by an ejected object or injured by unstable equipment. These risks occur during production and also during setting, cleaning, unjamming, maintenance, lifting and dismantling. Assessment identifies moving parts, access points, potential failure, energy sources and the people who could enter the danger zone. Safer design, suitable equipment, fixed or interlocked guarding, segregation and secure isolation take priority over warnings or protective clothing alone. Controls must remain effective when the machine changes mode or a task brings someone closer to the hazard. SHARE uses this group to connect machinery safety, work equipment, lifting, transport and maintenance control decisions.
Understanding Hazard group - mechanical hazards
Mechanical hazards arise from moving machinery, tools, vehicles, loads or components and from the unexpected release of stored energy. People may be cut, crushed, trapped, entangled, struck by an ejected object or injured by unstable equipment. These risks occur during production and also during setting, cleaning, unjamming, maintenance, lifting and dismantling. Assessment identifies moving parts, access points, potential failure, energy sources and the people who could enter the danger zone. Safer design, suitable equipment, fixed or interlocked guarding, segregation and secure isolation take priority over warnings or protective clothing alone. Controls must remain effective when the machine changes mode or a task brings someone closer to the hazard. SHARE uses this group to connect machinery safety, work equipment, lifting, transport and maintenance control decisions.
Why this matters at work
A familiar machine may be accepted without considering a new material, improvised access or an altered route through the work area. Repeated clearing may be treated as an operator problem while its design cause remains. Revisit suitability and prevention through competent assessment. A conformity mark, completed course or tidy photograph does not demonstrate that all task phases are controlled. Do not infer a technical setting or safe intervention from a generic mechanism description; obtain equipment-specific evidence and hold affected work where serious uncontrolled danger remains.
Mechanical harm follows movement and a path by which people or material enter its influence. Rotating stock, closing parts, transferred loads and ejected fragments create different questions. Evaluate the whole task cycle, including setting, clearing, cleaning, fault finding and maintenance, with operators and competent engineers. Safe production alone cannot establish safe intervention. HSE machinery guidance also identifies temperature, electricity and emissions interfaces: keep their appropriate source routes connected. Select equipment for actual conditions and people rather than assuming the original product description remains sufficient after relocation or change.
How organisations manage this in practice
Review a conveyor or machine task with operators and maintainers. Identify trapping and reach points, rotating parts, ejection paths, lifting interfaces and all energy sources before intervention. Select suitable work equipment and prevent access to dangerous parts with appropriate protective measures. Design safe interventions, isolate relevant energy and control residual pressure, gravity and other stored energy. Equipment assessment; guarding checks; maintenance and defect logs; isolation arrangements; lifting plans and examination records where required; training and authorised intervention procedures. Follow the assessment through procurement, implementation, briefing, supervision and verification rather than stopping at a document.
An acronym may produce a list of intentions while the only implemented action is instruction. PPE can be issued without reviewing moving-part interfaces, or workers may be punished for a task that protection makes impracticable. Resolve design and management causes with competent evidence. Training supports necessary safeguards and cannot replace them. The convention does not authorise access, set a safe residual score or prove compliance. Keep separately planned response and return conditions visible, with actual implementation verified before the responsible decision on affected use.
Record relevant users, task phases, equipment combinations, affected others and responsible owners. Check clear accessible instructions, actual understanding and adequate supervision with resourced competence. Identify where specialist care, lifting or design advice is required and retain that referral separately from general teaching. Verify contractor boundaries and the condition left for later shifts. Keep personal health information proportionate and protected while ensuring operational restrictions are communicated. Record changes in equipment or user circumstances, defects and action closure so the next worker understands the current assessed conditions.
What are mechanical hazards and what does their assessment cover?
Mechanical hazards arise from movement, contact, loss of stability, ejection and release of energy. Consider production, cleaning, unjamming, setting and maintenance rather than normal operation alone. Stopping a machine is not necessarily isolation. Manufacturer instructions and competent engineering assessment remain necessary. Distinguish supply conformity from safe use duties. See Safe use of work equipment and Lifting equipment at work.
Start with the hazard group overview, then use the related topic links for task-specific background. A group checklist helps discovery; it does not establish that the controls at your site are effective. Read the hazard group overview.
Which hazards should the assessment consider?
Check each relevant mechanism during normal work, cleaning, maintenance, foreseeable failure and emergencies. Several entries can share a harm pathway; follow the linked explanation rather than treating each label as a separate assessment. See Safe use of work equipment and Lifting equipment at work.
Hazard or exposure and practical application — part 1 of 4
Read the complete visual as text
- Moving machinery: Read the mechanism and controls: Moving machinery rotating parts and entanglement
- Rotating parts: Read the mechanism and controls: Moving machinery rotating parts and entanglement
- Entanglement: Read the mechanism and controls: Moving machinery rotating parts and entanglement
- Pinch points: Read the mechanism and controls: Pinch nip crushing cutting and shearing
Hazard or exposure and practical application — part 2 of 4
Read the complete visual as text
- Nip points: Read the mechanism and controls: Pinch nip crushing cutting and shearing
- Crushing hazards: Read the mechanism and controls: Pinch nip crushing cutting and shearing
- Cutting hazards: Read the mechanism and controls: Pinch nip crushing cutting and shearing
- Shearing hazards: Read the mechanism and controls: Pinch nip crushing cutting and shearing
Hazard or exposure and practical application — part 3 of 4
Read the complete visual as text
- Ejected parts: Read the mechanism and controls: Ejected parts and flying chips
- Flying chips: Read the mechanism and controls: Ejected parts and flying chips
- Conveyor hazards: Read the mechanism and controls: Conveyors and blockage clearing
Hazard or exposure and practical application — part 4 of 4
Read the complete visual as text
- Pressurised systems: Read the mechanism and controls: Pressure gravity and stored energy
- Stored energy release: Read the mechanism and controls: Pressure gravity and stored energy
- Lifting tasks and equipment modifications: Read the mechanism and controls: Lifting stability and changes
Describe when the source is created or released and how it reaches someone. Compare normal operation with receipt, setup, blockage, breakdown, disposal and contractor access. The list below is a discovery aid: an omitted mechanism may still be important, while an irrelevant item does not require a fabricated assessment. Follow the mechanism explanation and test controls against the actual circumstances before scoring risk.
| Hazard or exposure | Read the mechanism and controls |
|---|---|
| Moving machinery | Moving machinery rotating parts and entanglement |
| Rotating parts | Moving machinery rotating parts and entanglement |
| Entanglement | Moving machinery rotating parts and entanglement |
| Pinch points | Pinch nip crushing cutting and shearing |
| Nip points | Pinch nip crushing cutting and shearing |
| Crushing hazards | Pinch nip crushing cutting and shearing |
| Cutting hazards | Pinch nip crushing cutting and shearing |
| Shearing hazards | Pinch nip crushing cutting and shearing |
| Ejected parts | Ejected parts and flying chips |
| Flying chips | Ejected parts and flying chips |
| Conveyor hazards | Conveyors and blockage clearing |
| Pressurised systems | Pressure gravity and stored energy |
| Stored energy release | Pressure gravity and stored energy |
| Lifting tasks and equipment modifications | Lifting stability and changes |
How does access to a moving machine create a harm pathway?
Mechanical harm involves entry into a movement path, trapping at an interface or impact from material. Examine complete cycles, cleaning, setting, blockage clearing and maintenance. Hands, clothing, hair and tools may reach danger from unexpected positions. A conformity mark is not proof that an installation, modification or use is safe. Suitability, prevention of access, maintenance and competence remain important. See Safe use of work equipment and Equipment and machinery.
Look at the complete machine cycle and where people feed, remove, clean, adjust or clear material. A danger zone can exist at a moving interface, under a raised component or along the path of an ejected part. Prevent foreseeable access with suitable design and protection, and establish a separately planned safe state for intervention. A normal operator position is not the only place from which someone can reach the hazard.
Why is stopping a machine different from isolating its energy?
A stop command may leave electricity, pressure, gravity, springs or rotating mass available. Plan interventions with every relevant energy source controlled, including residual energy and substances. Isolation must remain effective for all personnel. A permit coordinates work but is not the physical isolation. Restart checks must account for people, tools and protective arrangements. See The safe isolation of plant and equipment and Safe use of work equipment.
Stopping normal motion changes the operating state but may leave electrical, hydraulic, pneumatic, spring or gravity energy available. A task-specific safe state requires competent identification, control and verification of those sources. Linked plant and other people can also reintroduce motion. The supervisor coordinates boundaries and the authorised maintainer controls hand-back; a button, warning notice or verbal promise is not proof that the relevant energy has been controlled.
How can a rotating part draw a person into machinery?
Contact can draw a person into machinery before withdrawal. Clothing, hair or carried items can enter the danger zone. See Safe use of work equipment.
A rotating shaft catches clothing, an operator reaches towards a moving chuck or a cleaner approaches an exposed drive. Motion pulls the person into a narrowing space faster than they can withdraw. Loose gloves, clothing or material can create the connection even without deliberate contact.
Which source controls and checks change the outcome?
Remove access through equipment and process design, select a safer handling method and provide suitable guarding or protective systems. Competent designers and maintainers verify protection over the full operating cycle, including cleaning and setup. Operators follow the assessed method and keep unsuitable clothing or Personal protective equipment (PPE) away from rotating parts. Stop for a missing guard, defeated interlock or unexpected movement; instruction is not an alternative to a required physical safeguard.
How should the controls be applied?
Prevent access with suitable engineering protection and design interventions without reaching into danger.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Check all access positions and non-production tasks. Missing or bypassed protection requires escalation before continued use.
Where do trapping, crushing, cutting and shearing injuries occur?
Rollers, platens, blades and sliding parts can trap or sever tissue. Transfer points may be as significant as the main tool. See Safe use of work equipment.
A closing press traps a hand, a powered door crushes someone at its edge and a conveyor nip draws material and fingers between surfaces. The danger zone can move with a slide, load or tool. Adjustment and fault finding often bring people closer than normal production.
Which source controls and checks change the outcome?
Eliminate unnecessary access, redesign feeding or setup and provide competent protective measures suited to the machine and access pattern. Verify guards, interlocks or other protective devices through the approved inspection and functional-check arrangements, not an improvised challenge with a body part. Task methods and residual PPE do not make an accessible trapping point safe. Stop and quarantine when protection fails or access cannot be controlled; repairs and release require authorised competence.
How should the controls be applied?
Identify movement envelopes and provide suitable protective measures and safe handling methods.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Observe changeovers and jams. Emergency stops are not substitutes for preventing contact.
How can a workpiece, tool or chip be ejected towards people?
Failed tooling, insecure workpieces and waste can leave equipment at speed and affect nearby people. See Safe use of work equipment.
A poorly secured workpiece leaves a rotating machine, a tool fails or a cutting process throws chips towards a nearby worker. Impact can injure eyes, skin or the whole body, and a bystander may be outside the operator's assumed danger area. Material, speed, tooling and restraint affect the release.
Which source controls and checks change the outcome?
Avoid a release-prone process or select suitable compatible tooling and securing arrangements; use designed containment and layout separation. The competent setter verifies compatibility and restraint against current equipment information. Operators check condition and stop for unusual vibration, loosening or a damaged screen. Eye or face protection supplements suitable containment; it cannot retain a heavy workpiece or justify exceeding an equipment rating.
How should the controls be applied?
Use suitable tooling and workholding, contain foreseeable ejection and maintain equipment.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Review material changes and manufacturer information; do not guess speed limits or guarding performance.
Why is clearing a conveyor blockage a high-risk intervention?
Rollers and transfers create trapping risks. Reaching for product or climbing across equipment may bypass safe use arrangements. See Safe use of work equipment and The safe isolation of plant and equipment.
A jam invites an operator to reach into a belt, roller or transfer point while production pressure continues. A stopped drive may restart automatically or stored energy may shift the trapped load. A second worker or upstream conveyor can reintroduce motion during the intervention.
Which source controls and checks change the outcome?
Reduce jams through product, feeder and access redesign; guard danger zones during operation. An authorised person plans and verifies task-specific isolation of relevant sources before intervention, including upstream interfaces and gravity. Supervisors control affected work and prevent unauthorised restart. Stop if the safe state or energy source is uncertain; an emergency stop or a verbal promise does not establish isolation. Hand back only after protection, tools and people have been checked.
How should the controls be applied?
Protect access and provide an effective intervention system controlling all relevant energy. Address recurring jam causes.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Observe the real unjamming method and verify isolation and safe routes with workers.
How can pressure, gravity or stored energy move equipment unexpectedly?
Raised loads, springs, pressure and material can move even after electrical isolation. Pressure leaks may cause injection injury. See The safe isolation of plant and equipment and Pressure systems.
A raised machine section drops, a spring-loaded component releases or hydraulic pressure drives a part after power is removed. Energy can remain in a load, accumulator or trapped volume. A gauge, switch or stopped motor may not show every energy source.
Which source controls and checks change the outcome?
Avoid access under unsupported components and reduce stored energy through design where feasible. Competent maintainers specify suitable isolation, restraint or support and verification for the actual task; improvised props or opening a fitting are not verification. Check the safe condition throughout the intervention and control other sources that could re-energise it. Stop on unexpected movement or incomplete system information. Release supports and restart only through the approved hand-back sequence.
How should the controls be applied?
Use competent equipment-specific restraint, support, depressurisation and verification.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. A gauge or control position alone may not prove safety; obtain appropriate engineering assessment.
How do a load change or loss of stability create mechanical risk?
Dropped loads, overturning and uncontrolled movement depend on equipment, attachment, ground and work interfaces. Modifications can alter protection. See Lifting equipment at work and Safe use of work equipment.
A lifting attachment is used with a changed load, an uneven surface destabilises a mobile machine or maintenance removes a supporting component. Crushing, dropped loads and overturning can involve people not operating the equipment. Centre of gravity, configuration and access can change without the overall load appearing larger.
Which source controls and checks change the outcome?
Avoid suspended-load exposure and choose suitable equipment and lift arrangements through competent planning. Verify actual load, configuration, attachment, condition and ground or support requirements using relevant equipment information. Keep people away from the drop or overturning path and control simultaneous work. Stop on unknown load, damaged attachment, unassessed configuration or unstable support; a training certificate does not resolve a missing lift plan or equipment limit.
How should the controls be applied?
Plan lifting competently and assess modifications before use. Control access and verify protective arrangements before restart.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Obtain specific capacity and examination evidence where relevant. A general guide cannot approve a lift or modification.
How should this hazard group be assessed and managed in practice?
Review a conveyor or machine task with operators and maintainers. Identify trapping and reach points, rotating parts, ejection paths, lifting interfaces and all energy sources before intervention. Select suitable work equipment and prevent access to dangerous parts with appropriate protective measures. Design safe interventions, isolate relevant energy and control residual pressure, gravity and other stored energy. Equipment assessment; guarding checks; maintenance and defect logs; isolation arrangements; lifting plans and examination records where required; training and authorised intervention procedures. Follow the assessment through procurement, implementation, briefing, supervision and verification rather than stopping at a document. See Safe use of work equipment and Lifting equipment at work.
Agree the activity, affected people and prerequisites with operations, workers and any contractor before work. Test whether the task can be removed or redesigned, then verify selected controls in the place they will operate. During work, the supervisor compares conditions with the assessed method and has authority to stop. Completion includes safe waste or equipment handling, outstanding defects and a named hand-back decision; a completed risk form is not the end of the control process.
What must be established before assigning a risk score?
Identify the actual activity, foreseeable harm, people exposed and controls already demonstrated to work. Consider start up, normal operation, cleaning, maintenance, breakdown, emergency response and simultaneous work. A numerical matrix may support prioritisation but cannot establish compliance or replace a specialist assessment. Do not assign a residual risk score merely because a proposed control has been written into a form. Keep unknowns explicit and obtain site evidence before deciding that work can proceed. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Write a short causal description: the work creates or releases something, a person is exposed by a particular route, and a specified injury or ill-health outcome is foreseeable. Establish whether existing measures work in the actual task before estimating likelihood. An unknown material, unverified safe state or absent critical control is a decision gap, not a reason to select a reassuring number. The responsible manager records what must be resolved and who can authorise the next step.
Who owns each control and how should it be verified?
The dutyholder provides resources and arrangements. The operational manager assigns each control to someone able to implement it. Supervisors verify the controls at the point of work and respond to defects. Workers and representatives explain work as done and report problems. Specialist advisers address limits of local competence. Record the control, responsible role, evidence, check method, due date and escalation route. Completion of a training course or signature alone does not demonstrate effective risk control. See Managing for health and safety (HSG65).
Separate the person who funds and owns the control from the person who performs its check. For an engineered measure, record the accepted performance or condition, who verifies it, what a failed result means and how maintenance is coordinated. For a staffing or organisational measure, check actual cover, authority and staff experience. A signature confirms a recorded action, not effectiveness. The supervisor must be able to hold work and obtain a competent remedy when the required condition is not met.
Who might be affected, including people outside the work team?
Include employees, agency workers, apprentices, contractors, cleaners, maintainers, delivery drivers, service users, visitors and nearby public. Consider inexperience, pregnancy, disability, health conditions, language needs and lone work individually and without stereotyping. Consultation should identify barriers to controls rather than collect unnecessary medical details. Share relevant interface information between employers. A single activity may require several hazard groups; avoid splitting the assessment so that interacting controls have no clear owner. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Walk through the job from the perspective of someone who has not received the operator briefing: a cleaner, visiting driver, contractor, new starter or occupant of an adjoining area. Ask whether a control protects them during arrival, normal work, waste removal and emergencies. Agree who controls each shared boundary and how changes are communicated. Individual needs influence a suitable arrangement but do not justify treating an employee, disability or health condition as the hazard.
When should the assessment be reviewed and what evidence matters?
Reassess when equipment, materials, staffing, layout, working hours or environmental conditions change; after incidents, near misses, complaints, symptoms or evidence of failed controls; and through planned risk based review. Verify improvements under realistic demand, not only during an announced inspection. Retain dated observations, measurements where relevant, maintenance records and action closure evidence. No single review interval suits every risk. Health surveillance, exposure monitoring and clinical diagnosis are different activities and require their own competent arrangements. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Use a change or failure to test the original assumptions, not merely change the date on the form. A different product, higher throughput, altered route, new shift or contractor may change the harm pathway. Keep observations, applicable measurements, defects and authorisation evidence linked to the task. After correction, verify under representative demand and with affected workers. Repeated workarounds or symptoms require investigation of the design and organisation, even when no injury has been recorded.
How could mechanical hazards arise in construction and civil engineering?
In construction and civil engineering, construction crews cut material in shared areas. Provide suitable guarding and work handling. Protection checks. This is an illustrative application, not a documented case or a complete method statement. See Safe use of work equipment.
Cutting can draw a hand into the blade or eject material towards another trade.
The supervisor checks the guard, work support and exclusion against the actual cut. A missing guard or unstable support stops cutting; only competent repair and reassessment allow release.
How could mechanical hazards arise in manufacturing and engineering?
In manufacturing and engineering, press operators clear scrap. Redesign intervention and isolate energy. Observed clearing and isolation. This is an illustrative application, not a documented case or a complete method statement. See Safe use of work equipment and The safe isolation of plant and equipment.
Scrap clearance can expose a worker to a press stroke or stored movement, causing crushing or amputation.
Production and maintenance first redesign recurring clearance. Hold an intervention if the safe state cannot be verified; record the fault, authorised isolation and controlled restart rather than accepting a normal stop.
How could mechanical hazards arise in warehousing and logistics?
In warehousing and logistics, warehouse conveyors jam at transfers. Address causes and protect access. Maintenance and intervention records. This is an illustrative application, not a documented case or a complete method statement. See Safe use of work equipment.
A transfer jam invites reaching between rollers; restart can trap or draw in the worker.
The supervisor restricts access and calls the authorised maintainer. A repeated jam needs a feed and design review; do not release the conveyor with a bypassed interlock.
How could mechanical hazards arise in agriculture and forestry?
In agriculture and forestry, farm workers maintain rotating drives. Prevent shaft access and plan isolation. Guard and maintenance checks. This is an illustrative application, not a documented case or a complete method statement. See Safe use of work equipment.
An exposed rotating drive can wind clothing around the shaft and cause fatal entanglement.
The farm manager checks guards and access before operation and plans maintenance in a verified safe state. Missing protection stops the equipment, not just the person currently beside it.
How could mechanical hazards arise in hospitality and food production?
In hospitality and food production, food staff clean mixers. Design safe cleaning and verify isolation. Cleaning and energy records. This is an illustrative application, not a documented case or a complete method statement. See The safe isolation of plant and equipment.
A mixer can restart or release stored movement while a cleaner reaches inside.
The supervisor coordinates hygiene and maintenance so the cleaning method preserves verified safe access. A failed interlock, uncertain energy state or improvised reach-in is a hold point; document the correction and authorised hand-back.
How could mechanical hazards arise in retail and public services?
In retail and public services, retail staff operate compactors. Protect crushing zones and restrict intervention. Protection checks. This is an illustrative application, not a documented case or a complete method statement. See Safe use of work equipment.
A compactor can crush someone reaching into the loading or discharge zone.
The store manager prevents public access and checks protection for normal use and blockages. Staff must not bypass a guard to meet collection deadlines; restrict use until competent restoration.
How could mechanical hazards arise in offices and professional services?
In offices and professional services, facilities maintain powered doors. Control closing movement during maintenance. Inspection handover. This is an illustrative application, not a documented case or a complete method statement. See Safe use of work equipment.
A powered door can close unexpectedly on a maintainer or passer-by.
Facilities staff separate maintenance from occupied access and obtain the competent safe-state method. Loss of separation or unexpected movement stops the job; test and authorise the door before normal access resumes.
How could mechanical hazards arise in education and laboratories?
In education and laboratories, learners use rotating workshop machinery. Match access and supervision to competence. Observed instruction and checks. This is an illustrative application, not a documented case or a complete method statement. See Safe use of work equipment.
Rotating tools can catch loose material or clothing and eject work towards learners.
The workshop supervisor checks competence, work holding and protection for the specific operation. An unsuitable setup or untrained change stops the exercise; instruction alone does not compensate for missing guards.
How could mechanical hazards arise in utilities and waste management?
In utilities and waste management, waste staff clear balers. Plan restraint and stored energy control. Isolation verification. This is an illustrative application, not a documented case or a complete method statement. See The safe isolation of plant and equipment.
A baler blockage can release compressed material or stored hydraulic movement and crush a worker.
The authorised maintainer establishes the task-specific safe state and required restraint. Unknown energy or unstable material is a hold point; verify the completed intervention and restart conditions with operations.
How could mechanical hazards arise in energy and process industries?
In energy and process industries, process maintenance opens hydraulic plant. Control pressure and movement before opening. Energy inventory. This is an illustrative application, not a documented case or a complete method statement. See The safe isolation of plant and equipment and Pressure systems.
Hydraulic pressure can move an actuator or release fluid force when a line is opened.
The competent maintainer accounts for every relevant energy source and retained load. Do not open a system on the basis of a gauge alone; unresolved pressure or movement stops the intervention and needs competent verification.
How could mechanical hazards arise in events and transport operations?
In events and transport operations, stage crews move powered structures. Plan lifting and movement envelopes. Lift plan and handover. This is an illustrative application, not a documented case or a complete method statement. See Lifting equipment at work and Safe use of work equipment.
A moving stage section can crush a crew member or fall onto an occupied area.
The lifting coordinator checks load, movement envelope and communication for the actual setup. A person entering the exclusion or loss of control communication stops movement; authorise hand-back before admitting others.
How do you put the controls into practice?
High-pressure fluid injection needs immediate treatment
A suspected fluid-injection injury needs immediate professional medical treatment, even if the wound looks small. Tell the treating team that high-pressure injection may have occurred and identify the fluid if known. Do not touch a pressurised leak or attempt self-treatment.
Move from recognising harm to deciding, implementing, checking and improving the controls. Give each critical control an owner, a check method and a clear escalation route. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
- Understand the taskObserve people, equipment, materials and interfaces.
- Describe the harmIdentify exposure, energy release and foreseeable failure.
- Control at sourceAvoid, redesign, substitute, contain or separate the hazard.
- Check in real workVerify performance, defects, ownership and change triggers.
| Stage | Action | Who acts | Evidence to retain |
|---|---|---|---|
| Before work | Confirm the actual task, people, equipment, substances, location and abnormal conditions. | Operational manager with competent advice | Assessment, observations, consultation and required specialist checks |
| Control delivery | Select suitable work equipment and prevent access to dangerous parts with appropriate protective measures. Design safe interventions, isolate relevant energy and control residual pressure, gravity and other stored energy. | Responsible manager and authorised implementers | Equipment assessment; guarding checks; maintenance and defect logs; isolation arrangements; lifting plans and examination records where required; training and authorised intervention procedures. |
| During work | Supervise the real activity; check that critical controls remain effective and workers can report problems. | Supervisor and workers | Checks, defects, changes and escalations |
| Stop and restart | Stop the affected activity when serious danger or a failed critical control is suspected. Restart only through the competent site authorisation arrangements. | Supervisor and authorised competent person | Reason for stopping, corrective action, verification and restart authority |
| Review | Revisit controls after change, incidents, near misses, symptoms or repeated defects. Check effectiveness rather than counting completed forms. | Manager, Occupational safety and health (OSH) adviser and worker representatives | Dated review, closure evidence and lessons for design and procurement |
How does ERICPD apply to mechanical hazards?
ERICPD stands for Eliminate, Reduce, Isolate, Control, PPE and Discipline. For mechanical hazards, start by removing the hazardous task or source where practicable, then reduce and separate the remaining exposure. Combine suitable safeguards and work arrangements, use relevant personal protective equipment for residual risks, and keep all selected measures effective in everyday work. See HSE: Managing risk using PPE and Managing for health and safety (HSG65).
- 1 · E Eliminate
Remove the hazardous task or source where practicable; confirm that the alternative still fulfils the task and assess remaining hazards.
- 2 · R Reduce
Use a suitable less hazardous material, process or equipment, or reduce the hazard at source. Check any new risks introduced.
- 3 · I Isolate
Separate people from the hazard through suitable containment, guarding, barriers or other task-specific separation.
- 4 · C Control
Put remaining safeguards and workable task arrangements in place. Engineering controls and administrative arrangements have different strengths.
- 5 · P PPE
Select personal protective equipment for relevant residual exposure. Check suitability, fit, compatibility, use and maintenance.
- 6 · D Discipline
Sustain the controls through management support, supervision, maintenance and learning. Resolve workarounds and failures without blaming workers.
Eliminate, Reduce and Isolate focus attention on the hazard and the exposure pathway before reliance on behaviour or PPE. Controls usually work together: an enclosure may still need safe access, maintenance and instruction. Record the reasons for choosing or rejecting stronger options and check the complete task, including cleaning, maintenance and foreseeable changes.
ERICPD is a practical learning mnemonic. The five-level hierarchy is elimination, substitution, engineering controls, administrative controls and PPE. Reduce may include substitution or source reduction; Isolate commonly involves engineering. Control can include engineering and administrative measures. Discipline supports every selected level and is not an additional protective barrier. These frameworks are related; their labels do not form identical statutory ladders.
What does each role need to know and demonstrate?
People need learning and demonstrated competence for the decisions they actually make, not the same course at every organisational level. See Safe use of work equipment and Lifting equipment at work.
For mechanical hazards, frontline learning must enable staff to keep outside danger zones and recognise failed protection. Supervisors need to challenge jam-clearing methods and control maintenance interfaces. Design, procurement and specialist assessment require deeper competence in guard design, energy control and safe hand-back. Awareness, supervised practice, assessment and authorisation are different stages; an attendance record alone does not establish competence or permit specialist intervention.
Assess practical understanding with the actual task and credible abnormal conditions. The assessor must be competent for the scope being tested; authorisation should state its boundaries. Reassess after a material change, a defect, a demonstrated gap or work outside that scope rather than assuming one fixed refresher interval suits every role.
| Role | Learning and decisions | Assessment, evidence and reassessment |
|---|---|---|
| Nearby staff and new starters | Recognise the relevant exposure, usable routes, warning signs and reporting or emergency arrangements. | Supervisor checks a practical explanation and scenario response; retain briefing scope and gaps. Repeat when routes or conditions change. |
| Frontline users | Demonstrate how to keep outside danger zones and recognise failed protection, including the checks, limits and stop decision. | Competent task assessor observes representative practice and a defect scenario; record task, equipment/material scope and authorisation. Reassess for changed methods or performance gaps. |
| Specialist workers and maintainers | Demonstrate the applicable technical method, safe state, interface controls and hand-back; do not infer specialist skill from general awareness. | Competent specialist assesses work within a defined scope; retain method, assessment and authorisation evidence. New equipment, material or fault type may need a new decision. |
| Supervisors and coordinators | Demonstrate how to challenge jam-clearing methods and control maintenance interfaces, manage a changed condition and hold or release work. | Manager or competent reviewer tests a realistic planning and stop/restart scenario; retain observed decisions and corrective actions. Review following interface failures. |
| Managers, purchasers and designers | Make and resource decisions on guard design, energy control and safe hand-back, including the stronger-control options and residual risks. | Competent review of specifications, trials, procurement acceptance and effectiveness evidence; record decision owner and outstanding actions. Reassess after process or organisational change. |
| OSH advisers, technical specialists and auditors | Distinguish jurisdiction and source limits, test representative evidence and recognise the boundary of their competence. | Appropriately competent review of the actual assessment, sources, sampling and closed actions; retain scope and limitations. Escalate missing technical information rather than inventing a conclusion. |
How can the hierarchy of controls reduce contact with dangerous machinery and moving parts?
Cartons repeatedly jam at a conveyor transfer point. Reaching between rollers can cause entanglement or crushing; an ordinary stop may leave stored energy or allow unexpected restart. Consider normal use, setup, cleaning and maintenance separately.
Illustrative SHARE example: assess stronger options first, then combine the measures needed for the remaining task. If elimination removes the task entirely, later measures address only remaining or different hazards. Each stage below explains what changes, how harm is reduced and who verifies it.
Applying ERICPD to other hazards in this group
Apply this reasoning to mixers, presses, rotating drives and powered doors: remove recurring access needs, select safer handling, guard danger zones and plan competent intervention. Gloves can introduce entanglement risk near rotating parts and should never be assumed to make access safe.
Keep an assessment record of the chosen controls, reasons for the selection, action owner, verification evidence and failure response. A failed critical control requires the affected activity to be held and corrected through the competent site arrangements; PPE or a completed form does not override that decision.
Guidance supporting these teaching examples
How would a farm machinery cleaning task differ from normal operation?
Manage this activity by preventing exposure at source, coordinating the affected people and verifying the planned controls before release. A farm machine requires removal of wrapped material after operation. Rotation may have stopped while gravity, springs or another stored-energy source remains. The operator and a helper may approach from different sides, creating an unexpected restart or movement interface. See Safe use of work equipment and The safe isolation of plant and equipment.
Illustrative SHARE workplace example
What must be agreed before work starts?
The manager first considers equipment and operating changes that prevent wrapping or permit remote clearing. Where access is necessary, an authorised competent person plans the task with actual machine information, establishes suitable energy isolation and restraint and verifies the safe state. A helper knows the controlled area and restart authority. Missing instructions or uncertain stored energy is a hold point.
What changes, stops or hand-back decisions matter?
During clearing, do not bypass protection, reach towards an unverified part or use improvised supports. Unexpected movement requires stopping and reassessing. After completion, the authorised person checks tools, people, guards and safe condition before controlled hand-back. Record the cause and corrective action; recurrent wrapping is a design or maintenance issue, not simply a reason to repeat the intervention faster. PPE selection must consider entanglement as well as cut protection.
How should jurisdiction, local rules and management assurance be handled?
Apply the law and regulator guidance for the work location, then use competent task and equipment information to establish the practical arrangements. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Health and Safety Executive (HSE) guidance generally addresses Great Britain; Northern Ireland has its own instruments and Health and Safety Executive for Northern Ireland (HSENI) route. Construction, dangerous substances, equipment and other specialist topics need the applicable instrument, not a Great Britain (GB) duty copied into a Northern Ireland (NI) answer. Fire arrangements also differ across the United Kingdom (UK) nations. Foreign project examples require destination-specific official advice and competent local assessment.
Distinguish a legal duty, regulator guidance, an organisation's rule and an illustrative SHARE method. A management system can link assessment, procurement, competence, maintenance, consultation and corrective action; a certification label or an unverified standard clause does not authorise work. For this group, sample evidence on guard design, energy control and safe hand-back and compare the recorded method with the activity observed on site. Resolve conflicts or missing technical information with the responsible competent person.
How would responding to a jam on a packing conveyor work in practice?
An operator notices a jam near a moving conveyor nip point. Reaching in can lead to entanglement or crushing, and stopping the normal cycle does not necessarily control stored energy or unexpected restart. The manager first seeks a design that prevents the jam and allows safe access, rather than normalising frequent manual intervention. See Safe use of work equipment and The safe isolation of plant and equipment.
Illustrative SHARE workplace example
What is required before and during the activity?
Before an intervention, the authorised maintainer plans the task-specific isolation and verification using the site procedure and equipment information. The supervisor secures the affected work and interfaces. During the intervention, preserve the verified safe state and respond to any unexpected movement or uncertainty by stopping and escalating; an untrained person must not bypass guards or improvise an isolation method.
What does safe completion and hand-back require?
After completion, the authorised person checks guarding, tools, people and the safe condition before the agreed hand-back and restart. Record the fault, isolation and verification, corrective action and release. Repeated jams trigger a design and maintenance review. An agricultural machine or a powered hospital bed has a different energy and access profile.
Acronyms and terms
These terms distinguish the source of harm, the exposure route and the controls needed for the actual work.
| Letters or term | Expansion or definition | Meaning in this topic |
|---|---|---|
| UK | United Kingdom | A geographical description, not one identical set of health-and-safety instruments. |
| GB | Great Britain | England, Scotland and Wales; HSE guidance is generally framed for this jurisdiction. |
| NI | Northern Ireland | A separate health-and-safety legal route overseen by HSENI. |
| HSE | Health and Safety Executive | The GB regulator and a publisher of official workplace guidance. |
| HSENI | Health and Safety Executive for Northern Ireland | The NI regulator; check its applicable requirements and advice. |
| OSH | Occupational safety and health | Preventing work-related injury and ill health. |
| PPE | Personal protective equipment | Equipment worn for remaining exposure; it does not replace stronger source controls. |
| Control of Substances Hazardous to Health (COSHH) | Control of Substances Hazardous to Health | The GB hazardous-substance assessment and exposure-control route. |
| PUWER | Provision and Use of Work Equipment Regulations | GB requirements for suitable work equipment, protection and competent use. |
| ERICPD | Eliminate, Reduce, Isolate, Control, PPE, Discipline | A learning mnemonic for selecting and sustaining controls; not a statutory ladder. |
| Hazard | A source or condition with potential for harm | Describe what creates harm, rather than calling a person the hazard. |
| Exposure | A route or contact connecting source and person | Consider dose, duration and circumstances where relevant. |
| Critical control | A measure essential to the safe arrangement | Define its required condition, check, owner and failure response. |
| Hand-back | Controlled return to operation or use | Confirm people, equipment, protection and outstanding conditions before release. |
Example handy documents
Useful records connect the actual task to control ownership, checks, stop decisions and verified hand-back. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
The following are examples of documents an organisation could create or adapt, not downloadable files or a complete safe system. Use the task-specific information and competent review before applying them. Keep private health information outside general operational records.
What should a task and harm-route assessment contain?
Record people, source, exposure or energy, foreseeable harm, existing controls, stronger options, residual uncertainty and the responsible decision owner.
What should a critical-control check and defect log contain?
Record the required condition, check method, responsible person, failed result, restricted work and verified corrective action.
What should a change and hand-back record contain?
Capture changed material, equipment, staffing, layout or conditions; prerequisites, hold decisions, competent verification and restart authority.
What should a competence and authorisation record contain?
Name the assessed task and scope, practical evidence, assessor, limits, supervision and reassessment triggers.
What should an operational learning review contain?
Link observations, complaints, near misses or relevant exposure evidence to a design or organisational change and an effectiveness check.