SHARE Knowledge Hub

Work Equipment

Work equipment includes machinery, tools, appliances and installations used at work, from a hand tool to mobile plant. Unsafe selection, access to moving parts, stored energy or failed maintenance can cause crushing, cuts, ejection, electric shock and other harm during use or intervention. Choose equipment for the real task and setting, prevent contact with danger, check it remains safe and stop use when a critical control fails.

Updated 2026-10-19GB and NI

Understanding Work Equipment

Work equipment includes machinery, tools, appliances and installations used at work, from a hand tool to mobile plant. Unsafe selection, access to moving parts, stored energy or failed maintenance can cause crushing, cuts, ejection, electric shock and other harm during use or intervention. Choose equipment for the real task and setting, prevent contact with danger, check it remains safe and stop use when a critical control fails.

Why this matters at work

Powered tools can injure through cumulative exposure even when mechanically guarded. Plan out high-vibration or dusty operations; choose lower-emission equipment, maintain sharp accessories, use suitable extraction or water suppression, reduce the force and time needed, and structure work to limit exposure. Gloves keep hands warm but do not control vibration exposure.

Mechanical hazards include entanglement, drawing-in, shearing, crushing, cutting, puncture, impact, friction and ejection. A moving part can draw clothing or hair in before a person reacts. A slowly moving ram can crush with substantial force, while a blade may continue to rotate after switch-off. Non-mechanical hazards include electrical, thermal, pressure, fire, noise, vibration and hazardous emissions.

How organisations manage this in practice

Operating controls should be identifiable, accessible and arranged to prevent unintended activation. Start or a significant change should generally require deliberate action. Stop controls need priority over start, and stopping should bring equipment to a safe condition. An emergency stop is required where appropriate and must be accessible to those who may need it.

Control-system changes and interlocks need competent design and functional validation. Users should know the normal stop, emergency stop and isolation separately. If a control fails or response is uncertain, take the equipment out of use.

Keep inspection results and defect actions accessible and maintain any existing maintenance log. Make clear who can remove equipment from service, arrange repair and verify safe return. Check examination requirements under additional regimes where relevant. A sticker should link to meaningful evidence and cannot override today's defect. Review frequency and scope after damage, significant changes, exceptional events or evidence of deterioration. For simple low-risk items, proportionate arrangements may be enough; complex or safety-critical equipment needs more detailed competent inspection. Avoid importing intervals from another machine merely because both are called work equipment.

A stopped machine can still contain energy

Four connected duties cover selection and safeguarding, routine operation, planned intervention, and verification or release. Stopping motion is different from controlling all energy.

Stopped pillar drill with guard in a UK engineering workshop. Photorealistic illustration.
Illustrative UK workplace scene. Read the practical checks below for responsibilities, evidence and limits. Download image · Download smaller image
  1. Identify all sources

    Consider electrical supply, air pressure, gravity and stored mechanical energy as relevant to the actual machine and linked equipment.

  2. Plan intervention

    Use equipment-specific isolation, securing, restraint and competent verification before access; one padlock does not represent every source.

  3. Separate testing and production

    Controlled testing needs its own arrangements, followed by named operating hand-back when the safeguards and work conditions are verified.

  4. Check task-specific PPE

    Do not imply gloves are suitable near rotating machinery: hand protection can introduce entanglement. A stopped drill photo is not an isolation demonstration.

Read the complete task-specific control examples

ERICPD is a planning cross-map: Discipline verifies and sustains every control. ESEAP compares effectiveness. A label does not authorise the task; retain the owner, evidence and stop or change decision.

Work Equipment · ERICPD

Eliminate
Remove a hazardous equipment step by redesigning material flow, for example avoiding manual feeding into a dangerous operating zone.
Reduce
Select equipment and a feed or handling method suited to the material, space, frequency and users.
Isolate
Prevent access to dangerous parts through suitable guards or protective devices and control all relevant energy for maintenance.
Control
Restrict high-risk use and maintenance to suitable people, provide task instructions and pre-use checks, and plan safe handback.
PPE
Check compatibility with the task; gloves may introduce entanglement risk on some rotating machinery and need a specific assessment.
Discipline
Maintain equipment and protective devices, inspect when required, control modifications and learn from defects.

Work Equipment · ESEAP

Elimination
Remove a hazardous equipment step by redesigning material flow, for example avoiding manual feeding into a dangerous operating zone.
Substitution
Select equipment and a feed or handling method suited to the material, space, frequency and users.
Engineering controls
Prevent access to dangerous parts through suitable guards or protective devices and control all relevant energy for maintenance.
Administrative controls
Restrict high-risk use and maintenance to suitable people, provide task instructions and pre-use checks, and plan safe handback.
PPE
Check compatibility with the task; gloves may introduce entanglement risk on some rotating machinery and need a specific assessment.
SHAREsimulate

How can I practise this topic in 3D?

A concrete hose is cleared without controlling pressure
3D workplace practiceSHAREsim

A concrete hose is cleared without controlling pressure

All related inspection points 5 across 1 location
Construction site 5 inspection points

Practice in the SHAREhub environment. Browser practice is separate from workplace competence and formal learning records.

What should a worker do before using work equipment?

Confirm the equipment is the right type for the task, check guards and controls, inspect for obvious damage, understand the safe method and emergency response, keep others clear, and stop if condition or permission is uncertain. The Provision and Use of Work Equipment Regulations (PUWER) set the workplace-use route in Great Britain, with a separate Northern Ireland instrument.

Do not begin because the equipment ran yesterday, carries a conformity mark or belongs to a contractor. Check any recorded limitation, attachment, inspection status and local authorisation that the task actually requires.

Identify equipment and task. During use: Use within assessed conditions.; At completion: Stop safely and leave controlled.

Check guards, controls and condition. During use: Watch for change or defect.; At completion: Report defects and hand back.

Confirm competence and area. During use: Keep others protected.; At completion: Record any hold or release.

What counts as work equipment and use?

Work equipment includes machinery, appliances, apparatus, tools and installations used at work, while use includes starting, stopping, programming, setting, transporting, repairing, modifying, maintaining, servicing and cleaning.

A hand tool, office appliance, machine line, scaffold component, ladder, lift truck or process installation may be work equipment. The applicable controls depend on the actual use and risk, not the label or purchase value.

Tool or appliance. Why it is in scope: Used to perform work.; Decision: Suitability and safe use.

Machine or installation. Why it is in scope: Creates mechanical or other energy hazards.; Decision: Guarding, controls and lifecycle evidence.

Cleaning or adjustment. Why it is in scope: It is use under PUWER.; Decision: Safe state and competent method.

Transport or modification. Why it is in scope: Can change condition or risk.; Decision: Planning, inspection and change control.

How do workplace-use duties differ from product-supply duties?

PUWER controls equipment provided or used at work; product-supply rules govern placing products on a market. A CE, UK Conformity Assessed (UKCA) or CE and UKNI route does not by itself prove workplace suitability, correct installation or safe use.

Choose the GB or NI market route and the product sector before relying on conformity documentation. Separately complete workplace selection, risk assessment, guarding, installation, competence, inspection and maintenance decisions.

How does unsafe work equipment cause harm?

A person can be caught, cut or struck when a dangerous part is accessible, a machine starts unexpectedly or material is ejected. Electricity, pressure, gravity, heat, noise and vibration add other routes to acute injury or longer-term ill health. Trace the task, exposed people, energy, failed safeguard and likely outcome before selecting controls.

Cleaning, setting, maintenance and defect recovery often bring hands close to danger and can leave stored energy. The worker is not the hazard; the design, condition, work method and failed protection are what must change. See HSE PUWER overview.

Task, exposure and harm route
Task and exposed peopleMechanism and possible harmStrongest feasible control and stop check
Operator reaches into moving machineryAn accessible nip or cutter can draw in a hand or clothing, causing crushing, amputation or fatal injury.Use suitable fixed or interlocked guarding and safe feeding; stop and isolate if a guard is missing or bypassed.
Maintainer clears a jamUnexpected restart or stored pneumatic, hydraulic or gravitational energy can strike or trap the person.Isolate, lock off, release or restrain all energy and prove the safe state before access.
Mobile plant crosses a shared routeBlind spots or unstable ground can cause collision, overturn or crush injury to nearby people.Choose suitable plant, separate pedestrians, assess route and ground, use trained operators; stop when segregation fails.
Repeated use of vibrating hand toolsHand-arm vibration and force can damage nerves, circulation or muscles over time.Select lower-vibration methods, maintain tools and manage exposure; review symptoms and monitoring signals.

How should work equipment be controlled across its life?

Control starts with need and specification, continues through purchase or hire, acceptance, installation, use, inspection, maintenance and change, and ends with safe decommissioning or disposal.

Four connected equipment duties

Four connected equipment duties. Readable native learning diagram with labelled relationships and an accessible text equivalent.
Learning point: Selection, safeguarding, operation, isolation and verified release form a lifecycle. GB/NI workplace duties and product-supply routes stay distinct.
Read the complete visual as text
  1. SELECT AND SAFEGUARD: Purchaser/operating owner matches actual task, people and environment. Fixed guarding comes first; other protection, jigs and residual-risk information cannot excuse missing physical protection.
  2. OPERATE WITH CONTROL: Authorised user needs safe start/stop, supervision and competence. Use includes setting, cleaning, maintenance and modification, not production alone.
  3. ISOLATE FOR INTERVENTION: Competent maintainer identifies all connected energy, separates and secures it, dissipates or restrains stored energy and verifies the safe state before access.
  4. VERIFY AND RELEASE: Inspector/operating owner reviews condition, required inspection and test evidence, restrictions and people readiness. Product marking and completed repair do not constitute workplace release.

Treat each transfer as an evidence gate. A check at purchase does not cover later deterioration, modification, relocation, new attachments, changed users or a different environment.

Select. Critical question: Is this the right equipment and control concept?; Evidence: Specification and risk decision.

Accept and install. Critical question: Is identity, condition and setup proven?; Evidence: Acceptance and commissioning.

Use and maintain. Critical question: Does it remain safe in real work?; Evidence: Checks, defects, maintenance and inspection.

Change or retire. Critical question: Has risk changed or energy been removed?; Evidence: Change review or decommission record.

Which hazards must the equipment assessment cover?

Assess mechanical contact and ejection together with electrical, pressure, thermal, chemical, ergonomic, noise, vibration, fire, explosion, mobility, stability and work-at-height hazards that the equipment or task can create.

Consider normal production, foreseeable abnormal events, clearing blockages, tool change, cleaning, testing, breakdown, maintenance and recovery after a stop. People nearby can be exposed even when they do not operate the equipment.

Hazard groupExamplesControl question
MechanicalCrushing, shearing, cutting, entanglement, drawing-in, ejection.Can access or energy be prevented?
EnergyElectricity, pressure, gravity, heat, stored motion.Can every source be isolated and dissipated?
ExposureDust, fume, noise, vibration, substances.Which separate regime and source control apply?
ContextMobility, stability, falls, traffic, fire.What environment and interface change the risk?

How should suitable equipment be selected?

Select equipment that is suitable for the intended task, people, environment, loads and conditions, with risks controlled by design and compatible guards, controls, attachments and information.

Prefer eliminating hazardous operations or choosing safer equipment before adding procedural controls. Include cleaning, maintenance, access, foreseeable misuse and emergency recovery in the selection decision.

Task and capacity. Question: Can it do the work within maker limits?; Reject or hold when: Duty or attachment is unclear.

People. Question: Can intended users operate and maintain it safely?; Reject or hold when: Access, reach or competence is unsuitable.

Environment. Question: Is it suitable for wet, dusty, explosive or public conditions?; Reject or hold when: Protection or compatibility is unproven.

Lifecycle. Question: Can it be inspected, isolated and maintained?; Reject or hold when: Safe intervention cannot be achieved.

What should a purchase or hire specification contain?

Specify the real task, materials, environment, users, foreseeable interventions, required safeguards, information, inspection and maintenance support, and the evidence needed before acceptance.

Do not procure from a catalogue description alone. Ask how the equipment will be installed, guarded, isolated, cleaned, maintained, moved, integrated and withdrawn from service.

Intended use. Procurement evidence: Duty, workpiece, environment and interfaces.; Acceptance gate: Matches actual work.

Safeguards. Procurement evidence: Guarding and control philosophy.; Acceptance gate: No accessible danger zone in assessed use.

Support. Procurement evidence: Instructions, parts, maintenance and competence needs.; Acceptance gate: Organisation can sustain safe use.

Market route. Procurement evidence: Applicable conformity and supplier documents.; Acceptance gate: Correct market and product sector.

How do equipment controls change across sectors?

PUWER-style decisions transfer across manufacturing, construction, warehousing and farming, but equipment, terrain, interfaces and specialist regimes change the control. A manager must identify who can stop use, who can repair or modify it and who can authorise return.

A mark or supplier declaration may inform product acceptance but does not prove the equipment is safe for the actual workplace task. GB and NI product-market routes differ, and workplace-use duties remain.

Setting, harm route and decisive control
Setting and peopleHarm routeControl, owner and stop check
Manufacturing line operatorA conveyor nip traps a hand during clearing or cleaning.Use fixed or interlocked protection and a no-entry clearing method; stop and isolate on guard failure.
Construction site teamA hired saw or breaker may be unsuitable for material, dust, power supply or changing ground.Specify the task and environment, verify condition and extraction, brief users; quarantine defects.
Warehouse driver and pedestriansMobile plant crosses pedestrian routes, creating collision or crushing risk.Segregate routes, confirm visibility, stability and competent operation; stop if separation fails.
Farm worker and contractorAn implement or vehicle can entangle, overturn or move unexpectedly on uneven ground.Check machine guards, terrain, attachment and isolation; stop use when a critical part is missing or damaged.

What does a conformity mark prove?

A conformity mark supports the applicable product-supply process; it does not prove that equipment is suitable for a particular workplace, correctly installed, maintained, guarded for every task or safe after modification.

In Great Britain, current guidance recognises UKCA and CE routes within their stated scope. In Northern Ireland, use the current CE or CE and UKNI route as applicable. Always check sector-specific rules and current dates. See GOV.UK placing UKCA or CE marked products on the Great Britain market.

EvidenceWhat it supportsWhat it cannot replace
Declaration and markingProduct-supply conformity route.Task suitability and risk assessment. GOV.UK placing UKCA or CE marked products on the Great Britain market.
InstructionsIntended use and residual risk information.Safe local installation and supervision. GOV.UK placing UKCA or CE marked products on the Great Britain market.
Workplace acceptanceCondition and integration at the site.Required ongoing maintenance and inspection. HSE PUWER overview.

How should equipment be accepted before first use?

Verify identity, condition, documentation, correct market route where relevant, intended use, guards, controls, accessories, installation needs, inspection status and support before the equipment enters service.

Record deviations and quarantine anything damaged, incomplete, unexpectedly modified or unsupported. Delivery paperwork alone is not a commissioning record.

Identity and specification. Evidence: Model, serial or asset reference and intended duty.; Hold point: Mismatch or unknown origin.

Condition and completeness. Evidence: Damage check, guards, accessories and instructions.; Hold point: Missing or damaged safety part.

Legal and support route. Evidence: Applicable supplier documents and service support.; Hold point: Wrong market route or no critical information.

Workplace readiness. Evidence: Installation, risk assessment and training plan.; Hold point: Site prerequisites absent.

What should installation and commissioning prove?

Commissioning should prove that the equipment is stable, correctly assembled and located, connected to safe services, guarded, controlled, isolated, documented and able to perform the intended task without creating uncontrolled risk.

Test safeguards and abnormal responses without exposing people. Integration with other machines, extraction, traffic routes or control systems needs a whole-system review.

Physical installation. Question: Is it stable, secure and safely accessible?; Evidence: Installation inspection.

Safeguards and controls. Question: Do guards, interlocks and stops work as intended?; Evidence: Functional test.

Energy and isolation. Question: Can all sources be safely controlled?; Evidence: Isolation test and diagram.

Operational handover. Question: Are method, competence and maintenance ready?; Evidence: Commissioning and release record.

What belongs in a pre-use check?

A pre-use check should cover visible condition, correct setup and attachment, guards and protective devices, controls, cables or hoses, stability, work area and any equipment-specific indicator identified by the assessment or manufacturer.

Equipment entry: suitability, evidence and event history

Equipment entry: suitability, evidence and event history. Readable native learning diagram with labelled relationships and an accessible text equivalent.
Learning point: Equipment entry: suitability, evidence and event history. Use the named evidence and owner for the actual task; this illustration does not authorise work or change the current review status.
Read the complete visual as text
  1. Start: Equipment is new, hired, moved, modified, repaired, inspected or proposed for use.
  2. Question 1: Are identity and intended duty matched to task, people and environment? Decision owner: Operating owner.
  3. YES: Determine GB/NI workplace, product-supply and specialist routes. Owner: Operating owner. CONTINUE → QUESTION 2.
  4. NO / UNKNOWN — HOLD: Hold; obtain specification, instructions and competent suitability evidence. Owner: Operating owner. HOLD → REPEAT QUESTION 1 AFTER CORRECTION.
  5. Question 2: Are jurisdiction and every applicable specialist/product-supply route resolved? Decision owner: Competent equipment owner.
  6. YES: Check condition, correct attachment, stability, safeguards, controls, information and required inspection. Owner: Competent equipment owner. CONTINUE → QUESTION 3.
  7. NO / UNKNOWN — HOLD: Hold; separate workplace use, product supply, lifting, mobile and other applicable duties. Owner: Competent equipment owner. HOLD → REPEAT QUESTION 2 AFTER CORRECTION.
  8. Question 3: Any missing, failed, damaged, defeated, overdue, mismatched or unknown item? Decision owner: Supervisor / competent inspector.
  9. YES: Stop, label/quarantine, protect people and report. Competent correction and accepted evidence return to this gate. Owner: Supervisor / competent inspector. HOLD → REPEAT QUESTION 3 AFTER CORRECTION.
  10. NO: Check history since last accepted release. Owner: Supervisor / competent inspector. CONTINUE → QUESTION 4.
  11. UNKNOWN: Quarantine until identity, state, safeguard and evidence uncertainty is resolved. Owner: Supervisor / competent inspector. HOLD → REPEAT QUESTION 3 AFTER CORRECTION.
  12. Question 4: Repair, modification, relocation, intervention, inspection return, emergency-stop use, unexpected movement or exceptional event since release? Decision owner: Operating owner.
  13. YES: Keep out of normal production; name recovery/change owner and affected scope. Use recovery/test guide. Owner: Operating owner. CONTINUE → Recovery verification and separate controlled testing.
  14. NO: Continue user, emergency-readiness and pre-use guide. Owner: Operating owner. CONTINUE → Production pre-use and monitored work.
  15. UNKNOWN: Hold; establish event/change history and affected scope. Owner: Operating owner. HOLD → REPEAT QUESTION 4 AFTER CORRECTION.
  16. Outcome: Unchanged accepted equipment goes to pre-use; event/change history goes to recovery first.

Production pre-use and monitored work

Production pre-use and monitored work. Readable native learning diagram with labelled relationships and an accessible text equivalent.
Learning point: Production pre-use and monitored work. Use the named evidence and owner for the actual task; this illustration does not authorise work or change the current review status.
Read the complete visual as text
  1. Start: Unchanged accepted equipment, or recovered equipment with named production-release evidence.
  2. Question 1: Are users authorised/competent, supervision suitable and emergency arrangements ready? Decision owner: Supervisor.
  3. YES: Perform defined pre-use check and establish work area. Owner: Supervisor. CONTINUE → QUESTION 2.
  4. NO / UNKNOWN — HOLD: Hold; close role-specific training, supervision, emergency or interface gaps. Owner: Supervisor. HOLD → REPEAT QUESTION 1 AFTER CORRECTION.
  5. Question 2: Does pre-use response match normal operation and assessed conditions? Decision owner: Authorised user / supervisor.
  6. YES: Authorise bounded normal production and monitor safeguards, controls, movement, sound, heat, vibration, leaks, people and task. Owner: Authorised user / supervisor. CONTINUE → QUESTION 3.
  7. NO / UNKNOWN — HOLD: Stop safely, quarantine and investigate through recovery verification. Owner: Authorised user / supervisor. HOLD → REPEAT QUESTION 2 AFTER CORRECTION.
  8. Question 3: Defect, changed condition, emergency stop, unexpected movement or uncertainty? Decision owner: Authorised user.
  9. YES: Move clear, use safe trained stop/emergency route, exclude/report/quarantine. Return to recovery verification. Owner: Authorised user. STOP / REFER → APPROPRIATE RESPONSE.
  10. NO: Complete normal stop, secure and clean by the approved safe method; record handback. Owner: Authorised user. OUTCOME → RECORD AND HAND OVER.
  11. UNKNOWN: Stop affected work and quarantine until competent evidence resolves state; do not reset and continue. Owner: Authorised user. HOLD → REPEAT QUESTION 3 AFTER CORRECTION.
  12. Outcome: Normal completion recorded, or quarantined equipment returns to recovery.
  13. Stop and escalation boundary: This route supplies no machine-specific setting, distance, safe load or test method.

A quick user check is not a substitute for a formal inspection. Its content and record depend on risk, equipment and the organisation's system; do not invent a universal checklist or sign-off interval.

CheckExample observationAction
ConditionDamage, wear, leakage or loose part.Stop and report if safety may be affected.
SafeguardsGuard or device missing, open or defeated.Do not use; quarantine.
ControlsStart, stop or indication abnormal.Hold pending competent decision.
Area and taskWrong attachment, unstable base or people exposed.Correct conditions before start.

How should equipment be monitored during use?

Use equipment only for the assessed task and conditions, keep safeguards in place, maintain exclusion and stability, watch for abnormal sound, movement, heat, vibration, leakage or control response, and stop before investigating a change.

Do not reach through a guard, defeat a device, clear a blockage live or rely on familiarity. A change in material, attachment, operator, environment or production method can invalidate the starting decision.

Unexpected movement or ejection. Immediate response: Stop from a safe position.; Next decision: Quarantine and investigate.

Guard or device changes state. Immediate response: Stop work and keep clear.; Next decision: Competent safeguarding review.

Abnormal noise, heat or vibration. Immediate response: Stop without close diagnosis.; Next decision: Maintenance assessment.

Task or environment changes. Immediate response: Pause the job.; Next decision: Reassess method and suitability.

What should happen when work finishes?

Stop the equipment through the defined sequence, leave moving and stored energy controlled, clean without entering danger, record defects or restrictions, and hand back the equipment and area in a known state.

Completion is not permission for maintenance. Any intervention requiring access to danger or stored energy needs its own isolation and authorised method.

Normal stop. Expected state: Movement ceases through intended control.; Evidence: User observation.

Secure and clean. Expected state: No unintended access, restart or unsafe residue.; Evidence: Task completion check.

Report. Expected state: Defects and restrictions are visible to the next user.; Evidence: Tag, log or handover.

Hand back. Expected state: Named owner accepts status.; Evidence: Release or continued hold.

How can the hierarchy of controls guide safe work-equipment selection and use?

Remove the hazard where reasonably practicable. If it remains, consider a safer method, engineering controls and safe work arrangements before personal protective equipment for residual risk.

HSE places elimination, substitution, engineering, administrative controls and personal protective equipment in that order. Verify that the chosen controls work on the actual task.

ERICPD (Eliminate, Reduce including substitution, Isolate, Control, personal protective equipment (PPE), Discipline) is a SHARE decision prompt cross-mapped to HSE’s five-level hierarchy. Choose stronger feasible controls first, verify them in the actual task and record why a stronger option cannot be used. Discipline means sustaining controls through maintenance, supervision and learning.

What is the guarding hierarchy?

Prevent access to dangerous parts with fixed guards where practicable, then use other guards or protection devices, then jigs, holders or push-sticks, with information, instruction, training, supervision and PPE only for remaining risk.

A guard must be suitable, effective, maintained, not easily bypassed and not create a new hazard. Guard design and safe distance are equipment-specific engineering decisions, not values to copy from this guide. See HSE L22 Safe use of work equipment.

PriorityControlBoundary
1Fixed guard.Use where practicable and compatible with necessary access. HSE L22 Safe use of work equipment.
2Other guard or protection device.Must fail or act to a safe condition as designed. HSE L22 Safe use of work equipment.
3Jig, holder, push-stick or similar aid.Keeps the person from danger where higher controls cannot fully apply. HSE L22 Safe use of work equipment.
4Information, training, supervision and PPE.Residual layer, not a substitute for practicable safeguarding. HSE L22 Safe use of work equipment.

How should interlocks and protective devices be managed?

If a guard interlock or protective device fails, move clear, use only the trained safe stopping action available from a safe position, warn others and report it; do not reach in, repeat the failed test, bypass or adjust the device. Quarantine affected equipment until safe isolation, competent repair, representative safeguard testing and named operating-owner release are recorded.

Do not tape, wedge, bridge, override or programme around a device to maintain production. Diagnostic or test modes require a designed safe method, restricted authority and equipment-specific controls.

Device functions normally. Meaning: Only evidence for the tested safeguard function.; Response: Continue within assessed use.

Intermittent trip. Meaning: Possible fault or changing condition.; Response: Stop, quarantine and diagnose safely.

Bypass found. Meaning: Safeguard no longer reliable.; Response: Isolate as needed and escalate.

Reset restores operation. Meaning: Does not explain cause.; Response: Investigate before release.

What makes starting, stopping and operating controls safe?

Controls should be identifiable, appropriate, reachable from a safe position, protected against unintended operation where needed, and arranged so starting occurs only through deliberate action and stopping brings equipment to a safe state.

The operator must understand normal stop, emergency response, reset and restart. A reset should not itself create hazardous movement unless the assessed control design specifically provides safe conditions.

Start. Expected behaviour: Deliberate action with danger zone clear.; Verification: Commissioning and user check.

Normal stop. Expected behaviour: Brings operation to intended safe state.; Verification: Functional test.

Mode or selector. Expected behaviour: Controls access and authority for the chosen mode.; Verification: Restricted setting and instruction.

Restart. Expected behaviour: No unexpected movement after interruption or reset.; Verification: Cause and safe-state check.

What is an emergency stop for?

An emergency stop is an additional rapid protective action, not normal stopping, guarding or isolation. After use, move clear, warn and report, exclude the area, control connected plant and do not reset, enter or investigate until authorised people apply the equipment-specific isolation; the named operating owner releases only after cause, repair, safeguard and controlled-test evidence is accepted.

Releasing an emergency stop does not prove a safe state or permit restart. Keep people clear and preserve the event state; emergency command governs any live emergency, while competent maintainers and control specialists govern isolated investigation and the operating owner governs return to service.

When is it used? Answer: For an emergency requiring rapid stop.; Boundary: Not the routine production stop.

What does it do? Answer: Acts with priority as designed.; Boundary: May not remove every energy source.

Does it isolate? Answer: Not necessarily.; Boundary: Apply the full isolation procedure.

Can it be reset and run? Answer: Only after cause and safe state are verified.; Boundary: Named return-to-service authority governs.

How should equipment be isolated?

Identify every energy source, stop and separate the equipment, prevent reconnection or release, dissipate or restrain stored energy, verify the safe state, control the work and restore only through the authorised sequence.

Guarded use and verified intervention

Guarded use and verified intervention. Readable native learning diagram with labelled relationships and an accessible text equivalent.
Learning point: Guarded use and verified intervention. Use the named evidence and owner for the actual task; this illustration does not authorise work or change the current review status.
Read the complete visual as text
  1. NORMAL GUARDED USE: Static conveyor/cutter has fixed guards, interlocked access where assessed, deliberate start, normal stop and additional emergency stop. Operator remains outside the danger zone.
  2. STOP IS NOT ISOLATION: A stopped machine may retain electrical, hydraulic/pneumatic, gravity, heat or stored mechanical energy. Emergency stop does not prove a safe state.
  3. PLANNED INTERVENTION: Authorised maintainer follows the actual-machine method: identify, separate, secure, dissipate/restrain and verify every source. Control access until verification.
  4. RESTORE AND HAND BACK: Restore guards and controls, inspect and test under separately controlled conditions, brief users and obtain named operating release before normal production.

Electrical isolation alone may leave hydraulic, pneumatic, pressure, thermal, gravity, spring, rotational or process energy. The actual isolation points, verification method and lock-off arrangements must come from competent equipment-specific planning. See HSE PUWER overview.

Energy or stageControl questionEvidence
IdentifyWhat can move, energise, pressurise, heat or release?Energy map and instructions. HSE PUWER overview.
Separate and secureCan reconnection or release be prevented?Isolation and lock-off record. HSE PUWER overview.
Dissipate or restrainWhat stored energy remains?Verified zero or safely restrained state. HSE PUWER overview.
RestoreAre people clear and safeguards restored?Controlled handback and release. HSE PUWER overview.

How should maintenance be planned?

Plan maintenance as work in its own right: define scope, condition, isolation, access, competence, tools, parts, coordination, testing, safeguards and handback before intervention begins.

Maintain equipment in an efficient state and good repair. Where maintenance cannot be done at rest, use an equipment-specific safe method and protection designed for that task; routine production pressure never supplies the justification.

Prepare. Control: Scope, hazards, safe state and people.; Evidence: Work order or task plan.

Intervene. Control: Isolation, access, tools and coordination.; Evidence: Permit or maintenance record.

Test. Control: Controlled test with restricted exposure.; Evidence: Functional and safeguard results.

Hand back. Control: Covers, guards and settings restored.; Evidence: Named acceptance and release.

When is a work-equipment inspection needed?

Inspect after installation where safety depends on installation, after assembly at a new site where applicable, and at suitable risk-based intervals or after exceptional circumstances that may jeopardise safety.

Frequency depends on the equipment, use, conditions, deterioration, manufacturer information and experience. This guide sets no blanket daily, weekly, annual or other interval. See HSE Inspection of work equipment.

TriggerPurposeDecision basis
Installation or assemblyProve safe installation before use.Equipment and installation dependency. HSE Inspection of work equipment.
Deterioration riskDetect safety-relevant decline in time.Risk, use, conditions and experience. HSE Inspection of work equipment.
Exceptional eventAssess damage or loss of integrity.Accident, modification, long disuse or severe condition. HSE Inspection of work equipment.
User checkIdentify obvious immediate defects.Separate from formal inspection where required. HSE Inspection of work equipment.

What inspection evidence is needed?

Where GB or NI PUWER requires an inspection, record the result and retain it at least until the next inspection under that regulation is recorded; keep it longer where another specialised regime or the organisation requires. This formal record is distinct from a simple pre-use check and from any specialised thorough examination.

A sticker can communicate status but is not the inspection result. Identify the equipment, inspection date and scope, findings, defects, action and competent person; where required, equipment used outside the undertaking must carry physical evidence of its last inspection.

Equipment identity. Why it matters: Links finding to the actual asset.; Limit: Avoid ambiguous family labels.

Scope and result. Why it matters: Shows what was examined and found.; Limit: A pass word alone may be insufficient.

Defect and action. Why it matters: Prevents unresolved return to use.; Limit: Track closure and restrictions.

Competent person and date. Why it matters: Shows accountable judgement.; Limit: No invented generic expiry.

What should happen when a defect is found?

Stop use where safety may be affected, bring the equipment to a controlled state, prevent further use, identify the defect, protect others, report it and keep it quarantined until competent evidence supports release.

Do not remove a tag, swap a guard, clear a jam or press reset as an informal return to service. The severity, affected equipment and connected systems must be understood first.

Immediate danger. Action: Stop, keep clear and isolate if safe and trained.; Release condition: Emergency or competent recovery route.

Safety device or guard defect. Action: Quarantine equipment.; Release condition: Repair and safeguarding verification.

Condition uncertain. Action: Treat as held.; Release condition: Competent inspection and evidence.

Minor non-safety issue. Action: Record and manage under local system.; Release condition: Decision still documented.

How should modification and change be controlled?

Keep modified, refurbished, relocated, integrated or reprogrammed equipment out of normal work until the change and affected scope are understood, workplace and product-supply duties are resolved, safeguards and controls are restored, applicable inspection and controlled tests pass, and the named operating owner records release. A commissioning or diagnostic test under a controlled plan is not permission for production use.

Recovery verification and separate controlled testing

Recovery verification and separate controlled testing. Readable native learning diagram with labelled relationships and an accessible text equivalent.
Learning point: Recovery verification and separate controlled testing. Use the named evidence and owner for the actual task; this illustration does not authorise work or change the current review status.
Read the complete visual as text
  1. Start: Equipment has been repaired, modified, moved, intervened upon or stopped after an exceptional event.
  2. Question 1: Are cause/change, affected scope, restoration, guards, controls and energy state verified? Decision owner: Recovery / change owner.
  3. YES: Confirm applicable inspection, instructions, method and competent people. Owner: Recovery / change owner. CONTINUE → QUESTION 2.
  4. NO / UNKNOWN — HOLD: Keep quarantined; investigate connected scope and restore actual-machine controls. Owner: Recovery / change owner. HOLD → REPEAT QUESTION 1 AFTER CORRECTION.
  5. Question 2: Is controlled commissioning or diagnostic testing required? Decision owner: Competent test owner.
  6. YES: Obtain separate competent test plan, controlled mode, exclusion, energy/safeguard controls, people and stop criteria. Testing is not production permission. Owner: Competent test owner. CONTINUE → QUESTION 3.
  7. NO: Record basis; still obtain named production-release acceptance. Owner: Competent test owner. CONTINUE → QUESTION 4.
  8. UNKNOWN: Keep isolated/quarantined; competent owner determines necessary tests. Owner: Competent test owner. HOLD → REPEAT QUESTION 2 AFTER CORRECTION.
  9. Question 3: Do functional and representative safeguard tests pass? Decision owner: Competent test owner.
  10. YES: Submit cause/change, restoration, inspection, test and restriction evidence. Owner: Competent test owner. CONTINUE → QUESTION 4.
  11. NO / UNKNOWN: Stop/quarantine and correct. Return to full recovery verification, not a reset-only retry. Owner: Competent test owner. HOLD → REPEAT QUESTION 1 AFTER CORRECTION.
  12. Question 4: Has named operating owner accepted cause/change, restoration, inspection, tests, restrictions, people and area evidence? Decision owner: Named operating owner.
  13. YES: Record production-release acceptance; continue pre-use and emergency-readiness checks. Owner: Named operating owner. OUTCOME → RECORD AND HAND OVER.
  14. NO / UNKNOWN — HOLD: Remain quarantined; repair, sticker or diagnostic success cannot bypass acceptance. Owner: Named operating owner. HOLD → REPEAT QUESTION 4 AFTER CORRECTION.
  15. Outcome: Named release proceeds to pre-use; test permission remains distinct from production permission.

A change to software, controls, guards, attachments, material, location or duty can alter stability, access, stopping, energy, exposure or maintenance. Quarantine unresolved changes and route every correction back through the affected engineering, inspection, test and operational-release gate.

ChangeWorkplace-use questionProduct-supply question
New attachment or dutyIs equipment still suitable and guarded?Does intended use or conformity scope change?
Control or software changeAre modes, stops and restart safe?Who now takes manufacturer responsibility?
RefurbishmentIs condition and performance demonstrated?Is it substantially changed or newly supplied?
IntegrationAre whole-system risks controlled?Does an assembly become a new product?

What training and competence are needed?

Users, supervisors and those who manage, inspect, maintain or modify equipment need adequate information, instruction and training for their role, with competence demonstrated for the actual equipment and task.

Simple equipment may be covered by suitable in-house instruction; complex or high-risk work may need specialist training and supervised experience. There is no universal certificate or refresher expiry. See HSE Training and competence for work equipment.

User. Competence content: Normal use, checks, limits, defects and emergency response.; Review trigger: New equipment, task or performance concern.

Supervisor. Competence content: Authorisation, observation, stop and release.; Review trigger: Change or control failure.

Maintainer or inspector. Competence content: Technical method, isolation and judgement.; Review trigger: Design change or scope extension.

Manager or purchaser. Competence content: Suitability, interfaces and assurance.; Review trigger: New process, supplier or regime.

Who may use specific-risk equipment?

Where equipment use presents a specific risk, restrict use to appointed people and restrict repairs, modifications, maintenance or servicing to specifically designated people with adequate training.

Appointment must match the equipment, task and limits. A generic induction, trade title or previous experience does not automatically authorise a different machine, intervention or site.

ActivityRestrictionEvidence
Normal specific-risk useAppointed and adequately trained people.Authorisation matrix.
Repair or maintenanceSpecifically designated competent people.Scope and competence record.
New attachment or modeReassess authorisation.Briefing and demonstration.
Visitor or contractorNo assumption from employer or badge.Interface and local acceptance.

What should supervision verify?

Supervision should verify authorised people, correct equipment and setup, guards and controls, the actual method, conditions during use, defect response and handback, with closer oversight where competence or risk requires it.

Supervision is an active control, not a signature. It should detect drift such as routine bypassing, wrong attachments, informal repairs, missed checks or production pressure overriding a hold.

Start. Observation: Identity, setup, guards and people.; Response: Permit or hold.

Work. Observation: Real behaviour and machine response.; Response: Coach, correct or stop.

Change. Observation: New material, mode or environment.; Response: Pause and reassess.

Finish. Observation: Defects, state and handback.; Response: Release or quarantine.

What must each equipment role learn and demonstrate?

The user must operate, check and stop the equipment safely; a maintainer must isolate and verify energy; an inspector must detect deterioration; a manager must select, resource and act on controls. Specific-risk equipment needs restricted use or maintenance by designated competent people. Training attendance alone does not prove the decision can be made safely.

Assess people on the equipment and task they will actually perform. Reassess after changes to machine, guard, controls, worksite, role, incident or a repeated unsafe behaviour pattern.

Role-specific competence and reassessment
RoleKnowledge and demonstrated actionAssessor and reassessment trigger
User and supervisorInspect before use, keep clear of danger, use controls correctly and stop a defective machine.Competent supervisor observes use and response to a defect; reassess after equipment or task change.
Maintainer and contractorIdentify all energies, isolate and prove zero or restrained state, repair and hand back safely.Authorised maintenance lead checks isolation and restart; reassess after modification or incident.
Inspector or examinerSelect inspection scope and interval from risk, detect deterioration and record action.Competent technical lead samples inspection and defect decisions; reassess after new equipment or failure.
Buyer, hirer and managerSpecify suitability, accept equipment, resource maintenance, set authorisation and quarantine routes.Senior owner reviews a real acceptance and defect file; repeat after supplier or use change.
Safety adviser or auditorTrace hazard, hierarchy, evidence, GB/NI legal scope and specialist regimes.Competent lead samples equipment in the field; repeat after legal or technical change.

Who is responsible for hired work equipment?

Hiring does not remove workplace-use duties: the supplier or hirer may have supply and maintenance obligations, while the employer or person controlling use must still ensure suitability, safe condition, inspection evidence, competence and safe operation.

Hired equipment: evidence crosses every handover

Hired equipment: evidence crosses every handover. Readable native learning diagram with labelled relationships and an accessible text equivalent.
Learning point: Hired equipment: evidence crosses every handover. Use the named evidence and owner for the actual task; this illustration does not authorise work or change the current review status.
Read the complete visual as text
  1. 1. SPECIFY: Hiring organisation specifies actual task, site, people and intended duty; supplier provides identified equipment, instructions and applicable evidence.
  2. 2. ACCEPT IDENTITY AND CONDITION: Host checks identity, attachment, condition and required inspection/examination information. Reject or quarantine a mismatch; delivery papers are not automatic acceptance.
  3. 3. ASSESS THE SITE: Competent owner confirms ground, route, environment, specialist regimes and emergency arrangements. A lowered static platform is not yet permission to elevate.
  4. 4. AUTHORISE AND CHECK: Supervisor verifies task-matched user authority/competence and pre-use condition. Lifting or work-at-height duties may also apply.
  5. 5. DEFECT OR JOINT HANDBACK: Stop/quarantine defects and use agreed contacts. Supplier, hiring organisation, host, supervisor and user retain their actual responsibilities; jointly record handback.

Agree in writing who selects, delivers, inspects, maintains, responds to defects and removes the equipment. Verify the agreement against what arrives and how it will actually be used.

Supplier or hire company. Question: What is supplied, maintained and documented?; Evidence: Specification, instructions and inspection evidence.

Hiring organisation. Question: Is it suitable for the actual workplace and task?; Evidence: Acceptance and risk assessment.

User and supervisor. Question: Are setup, competence and daily condition controlled?; Evidence: Briefing, checks and defect route.

Breakdown or return. Question: Who makes safe and who authorises movement?; Evidence: Call-out, isolation and handover.

How should contractor equipment be controlled?

The host and contractor should exchange task, site, equipment, competence, inspection, maintenance, isolation, emergency and defect information, then agree who controls each decision before work starts.

A contractor-owned machine is not automatically acceptable, and a host permit does not prove its condition. Shared or connected systems need one coordinated safe state and clear release authority.

Verify equipment and documents. During work: Coordinate exclusions and site conditions.; Handback: Report defects and restrictions.

Agree isolation and emergency interfaces. During work: Stop on mismatch or unsafe change.; Handback: Jointly confirm equipment and area state.

Name decision owners. During work: Protect other employers and the public.; Handback: Retain required evidence.

What additional issues apply to mobile work equipment?

Assess stability, visibility, routes, pedestrians, riders, falling objects, overturn, towing, braking, parking, attachments, ground conditions and maintenance for the actual mobile equipment and environment. A lifting task may also engage the Lifting Operations and Lifting Equipment Regulations (LOLER), with separate GB and NI instruments.

Do not infer a safe speed, slope, separation distance, load or braking performance from this guide. Use manufacturer limits, site design and competent assessment, and apply lifting rules when mobile equipment lifts loads.

Route and people. Question: Can vehicle and pedestrian movements be separated?; Boundary: Site-specific layout and control.

Stability and ground. Question: Are load, gradient and surface within limits?; Boundary: Manufacturer and competent data.

Operator and riders. Question: Are positions and restraints suitable?; Boundary: Equipment-specific requirements.

Attachment or lift. Question: Does duty change stability or legal regime?; Boundary: PUWER plus LOLER where applicable.

Which specialised regimes may also apply?

PUWER is not a complete answer where equipment lifts loads or people, contains pressure, uses electricity, supports work at height, creates substances, noise or vibration, or can ignite a dangerous atmosphere.

Determine applicability for the real equipment and task in the correct jurisdiction. Sector regimes for construction, mines, quarries, agriculture, rail or merchant shipping may also change duties and enforcement routes.

SituationAdditional routeBoundary
Lifting loads or peopleLOLER or NI equivalent as applicable.Separate thorough-examination and planning decisions. HSE LOLER overview.
Pressure or electricityPressure-systems or electrical-safety law.Specialist integrity and isolation. HSE Pressure systems.
Work at heightWork-at-height law.Access selection and fall prevention. HSE Work at height.
Dust, fume, noise, vibration or flammablesCOSHH, DSEAR, noise or vibration law.Separate exposure and ignition decisions. HSE Dangerous substances and explosive atmospheres.

Does the power-press branch apply?

Before using the general inspection route, identify whether a relevant power press working cold metal and its guards or protection devices falls within PUWER’s special provisions. In GB use the applicable PUWER power-press provisions and HSE L112; in NI check the separate PUWER (NI) 1999 provisions with HSENI. A generic risk-based inspection or service record alone does not discharge this specialist branch. The purchasing/asset owner obtains a competent applicability and examination plan before acceptance; no unidentified press interval is set here.

What should happen in a work-equipment emergency?

Raise the alarm, stop or isolate only through trained actions that are safe from the person's position, keep people out of danger, call the site emergency route and preserve the equipment state for competent recovery and investigation.

Unexpected movement or failed safeguard: protect first

2 linked parts. Follow the question numbers and complete the applicable route.

Part 1 of 2 · Questions 1–3

Unexpected movement or failed safeguard: protect first. Readable native learning diagram with labelled relationships and an accessible text equivalent.
Continue · Part 2 of 2 · Questions 4–5Unexpected movement or failed safeguard: protect first. Readable native learning diagram with labelled relationships and an accessible text equivalent.
Learning point: Unexpected movement or failed safeguard: protect first. Use the named evidence and owner for the actual task; this illustration does not authorise work or change the current review status.
Read the complete visual as text
  1. Start: Unexpected movement, ejection, abnormal control response or failed guard/stop/warning occurs.
  2. Question 1: Is anyone in immediate danger, trapped, injured or in an unstable/energised area? Decision owner: Worker / incident command.
  3. YES: Move clear, raise alarm and use site emergency/trained rescue route. Do not enter danger. Owner: Worker / incident command. STOP / REFER → APPROPRIATE RESPONSE.
  4. NO: Move clear, warn others and report. Owner: Worker / incident command. CONTINUE → QUESTION 2.
  5. UNKNOWN: Keep clear and escalate as potential emergency; no approach to clarify at personal risk. Owner: Worker / incident command. STOP / REFER → APPROPRIATE RESPONSE.
  6. Question 2: Can designed stop or remote action be safely used by a trained person? Decision owner: Trained operator.
  7. YES: Use approved action and report plant state; establish exclusion and command. Owner: Trained operator. CONTINUE → QUESTION 3.
  8. NO / UNKNOWN: Prevent approach; establish exclusion and emergency/operating command. Owner: Trained operator. CONTINUE → QUESTION 3.
  9. Question 3: Has emergency phase ended and recovery authority accepted handback? Decision owner: Emergency / operating authority.
  10. YES: Identify connected equipment and every energy source; apply equipment-specific isolation and verify safe state. Owner: Emergency / operating authority. CONTINUE → QUESTION 4.
  11. NO / UNKNOWN — HOLD: Remain excluded and support responders. No reset, guard opening, jam clearing or assumption that emergency stop is isolation. Owner: Emergency / operating authority. HOLD → REPEAT QUESTION 3 AFTER CORRECTION.
  12. Question 4: Are cause, affected scope, safeguards and condition understood? Decision owner: Competent investigation owner.
  13. YES: Repair/redesign, inspect and test stops, guards, reset and connected functions under separate controlled plan. Owner: Competent investigation owner. CONTINUE → QUESTION 5.
  14. NO / UNKNOWN — HOLD: Remain quarantined; extend investigation before any intervention or release. Owner: Competent investigation owner. HOLD → REPEAT QUESTION 4 AFTER CORRECTION.
  15. Question 5: Do required tests, procedures, competence, restrictions and affected-person readiness pass? Decision owner: Named operating owner.
  16. YES: Record return-to-service acceptance, then complete production pre-use guide. Owner: Named operating owner. OUTCOME → RECORD AND HAND OVER.
  17. NO / UNKNOWN — HOLD: Remain quarantined and correct gaps; no reset-only restart. Owner: Named operating owner. HOLD → REPEAT QUESTION 5 AFTER CORRECTION.
  18. Outcome: Emergency exclusion, continued quarantine or named accepted recovery followed by pre-use.

Do not approach moving, energised, pressurised, hot, unstable or damaged equipment to diagnose it. Rescue, firefighting and first-aid actions must follow the site plan and trained roles.

Person in danger. Immediate action: Raise alarm and use designed emergency control if safe.; Prohibited assumption: Do not enter the danger zone.

Unexpected movement or release. Immediate action: Keep clear and stop connected work.; Prohibited assumption: Emergency stop is not full isolation.

Fire, pressure or electrical event. Immediate action: Use the site emergency plan.; Prohibited assumption: Do not improvise specialist response.

After the event. Immediate action: Maintain exclusion and control evidence.; Prohibited assumption: No restart because conditions appear normal.

Who may return equipment to service?

The named operating owner should authorise return only after the cause is understood, repairs and safeguards are complete, inspection or testing matches the defect and risk, people are clear, documentation is updated and restrictions are communicated.

Repair completion, a reset, a replaced fuse, an inspection sticker or production need is not enough by itself. Serious events or modifications may require engineering, safeguarding, electrical, pressure, lifting or legal review.

Cause. Required evidence: Defect or event understood.; Owner: Competent investigator or specialist.

Restoration. Required evidence: Repair and safeguards verified.; Owner: Maintainer and tester.

Readiness. Required evidence: Method, competence, area and interfaces ready.; Owner: Supervisor and affected parties.

Authorisation. Required evidence: Signed or recorded release.; Owner: Named operating owner.

Who owns each work-equipment decision?

Assign owners for specification, acceptance, use, inspection, maintenance, isolation, modification, quarantine, emergency control and return to service; do not let responsibility disappear between departments or companies.

One person may hold several roles, but the evidence and competence requirements remain distinct. Emergency command and later operational release are separate decisions.

Specification and acceptance. Typical owner: Purchaser and technical owner.; Interface: User and maintenance input.

Use and supervision. Typical owner: Operating manager or supervisor.; Interface: Worker and nearby people.

Inspection and maintenance. Typical owner: Competent person and asset owner.; Interface: Defect and isolation system.

Return to service. Typical owner: Named operating owner.; Interface: Technical evidence and affected parties.

Which Great Britain duties are central?

In Great Britain, the Health and Safety at Work etc Act 1974, Management Regulations 1999 and PUWER 1998 form the central workplace route, with specialised regulations added according to the equipment and task.

Use current amended legislation and HSE guidance. L22 provides Approved Code of Practice (ACOP) and guidance for PUWER, while product-supply rules remain a separate current-market question.

LayerMain functionEvidence
HSWA 1974: Health and Safety at Work etc Act 1974.Safe plant, systems, information, training and protection of others.Governance and safe systems.
MHSWR 1999: Management of Health and Safety at Work Regulations 1999.Assessment, arrangements, coordination and emergency planning.Risk and interface records.
PUWER 1998: Provision and Use of Work Equipment Regulations 1998.Suitability, maintenance, inspection, guarding, controls and competence.Equipment lifecycle evidence.
Specialised law: HSE LOLER overview; HSE Pressure systems.Lifting, pressure, electrical, height, substances and exposures.Applicability-specific records.

Which Northern Ireland duties are central?

In Northern Ireland, the Health and Safety at Work Order 1978, Management Regulations Northern Ireland 2000 and PUWER Northern Ireland 1999 form the central workplace route, with separate NI or applicable specialist regimes added as needed.

Do not relabel Great Britain legislation as UK-wide. Use current NI legislation, HSENI guidance and the applicable Northern Ireland product-market route.

LayerMain functionEvidence
HSWA Order 1978: Health and Safety at Work Northern Ireland Order 1978.Safe plant, systems, information, training and protection of others.Governance and safe systems.
MHSWR NI 2000: Management of Health and Safety at Work Regulations Northern Ireland 2000.Assessment, arrangements, coordination and emergency planning.Risk and interface records.
PUWER NI 1999: Provision and Use of Work Equipment Regulations Northern Ireland 1999.Suitability, maintenance, inspection, guarding, controls and competence.Equipment lifecycle evidence.
Specialised NI or applicable law: Lifting Operations and Lifting Equipment Regulations (Northern Ireland) 1999; Pressure Systems Safety Regulations (Northern Ireland) 2004.Additional equipment or hazard duties.Jurisdiction-specific records.

How should work-equipment control be assured?

Assurance should test whether equipment is suitable, safeguards work, defects are controlled, inspections and maintenance match risk, competence is real, contractor interfaces work and return-to-service decisions are evidence based.

Use field observation and equipment sampling, not record presence alone. Trend repeated guard damage, bypasses, emergency stops, overdue actions, recurring faults and differences between shifts or sites.

Is the inventory complete? Evidence: Assets, location, owner and status.; Escalation: Unknown equipment held.

Do safeguards work in practice? Evidence: Observed use and functional evidence.; Escalation: Bypass or drift quarantined.

Are defects closed? Evidence: Traceable report, repair and release.; Escalation: Repeat or overdue issue reviewed.

Are people competent? Evidence: Demonstration and supervision.; Escalation: Restriction or refresher based on need.

Which warning signs require immediate attention?

Missing or defeated guards, unexpected movement, unreliable controls, recurring trips, damaged cables or hoses, leaks, unstable equipment, unknown modifications, expired required evidence or informal repairs require a stop, hold or competent review.

Also treat emergency-stop use, reports that workers must reach into danger, and workarounds that have become normal as control failures rather than operator inconvenience.

Guard opened or removed for production. Likely weakness: Safeguarding and workflow conflict.; Action: Stop and redesign or restore.

Frequent reset or emergency stop. Likely weakness: Unresolved fault or process instability.; Action: Quarantine and investigate.

Temporary tape, wedge or bridge. Likely weakness: Device defeated.; Action: Prevent use and escalate.

Inspection or modification unclear. Likely weakness: Evidence gap.; Action: Hold pending competent decision.

What do complete work-equipment decisions look like?

Four complete BuildOut Ltd cases cover routine guarded-drill work, hired mobile equipment, a failed interlock and emergency-stop recovery. Other interface summaries retain maintenance and modification boundaries; they are not six full worked cases. Actual equipment evidence and named authorisation govern.

BuildOut Ltd could use one asset lifecycle with risk-based gates for specification, acceptance, authorisation, use, defects, maintenance, inspection, change and release, while applying the correct GB or NI and specialist regime at each site.

How could BuildOut Ltd govern work equipment?

The teaching model keeps operations, engineering, procurement and contractors connected. It does not replace equipment-specific instructions, examinations, limits or site authority.

Specify. BuildOut owner: Procurement plus technical and user leads.; Minimum evidence: Task, environment and safeguard requirements.

Accept. BuildOut owner: Asset owner and competent installer.; Minimum evidence: Identity, condition, documentation and commissioning.

Operate. BuildOut owner: Supervisor and authorised user.; Minimum evidence: Checks, competence and method.

Hold and release. BuildOut owner: Operating owner with technical evidence.; Minimum evidence: Defect closure and recorded authorisation.

Each example is a training pattern, not an equipment permission. Replace every example details with the real machine, manufacturer instructions, energy sources, people, environment, inspection status and named authority.

Routine use. Primary decision: Start only after suitability, safeguards and checks pass.; End state: Controlled completion.

Hire or contractor. Primary decision: Accept only after duties and evidence align.; End state: Accepted, rejected or held.

Defect or emergency. Primary decision: Stop and prevent restart.; End state: Quarantine or authorised return.

Maintenance or change. Primary decision: Control energy and evidence.; End state: Verified handback.

Routine guarded pillar-drill task

Task material and setting: Training only, not authorisation for a real machine. Before drilling, an authorised user confirms the task, material, workholding, guard, controls, bit, area and permission. Stop and keep the drill unavailable for a loose workpiece, damaged bit, guard or control defect, unusual response or intrusion. Use the normal stop, wait for movement to cease and record defects; the workshop supervisor releases only after the check, briefing, defect closure and safe handback are accepted.

People and prerequisites: Authorised user and workshop supervisor; suitable drill, correct workholding and bit, current local assessment, functioning guard and controls, safe area and known defect route.

Before: Confirm the task and material, inspect the drill, guard, workholding and emergency control, remove loose items, set the work securely and keep others outside the operating space.

During: Keep the guard and workholding in position, use the intended controls, observe sound, movement and swarf, and stop before any adjustment or clearing.

Hold or stop: Do not start or continue for a loose workpiece, damaged bit, missing or defeated guard, unreliable control, unusual movement, unexpected material response or unauthorised person in the area.

Completion and hand back: Stop through the normal control, wait for movement to cease, leave the machine and area clean through the safe method, record any defect and hand back in a known state.

Evidence: Authorisation, pre-use check, task briefing, any defect report and supervisor release.

Hired mobile equipment arrives on site

Task material and setting: Training only, not permission to operate hired plant. Keep the platform out of service until identity, condition, instructions, applicable inspection or examination evidence, ground, route, weather, rescue plan and operator competence match the real task. Reject or quarantine any mismatch or uncertainty. The site supervisor accepts use only on the agreed evidence, and the supplier or site owner completes a recorded defect and return handover.

People and prerequisites: Hire supplier, site logistics lead, competent equipment assessor, authorised operator and supervisor; agreed specification, delivery evidence, site assessment, ground and route plan, rescue and defect arrangements, and any specialised examination evidence required.

Before: Match the delivered machine to the order, inspect condition and documentation, verify inspection or examination evidence applicable to the machine, confirm ground, access, weather and interface controls, and brief the authorised operator.

During: Use only within manufacturer and site limits, maintain route and people controls, observe stability and machine response, and stop for changed ground, weather, load, alarm or condition.

Hold or stop: Reject or quarantine the equipment for identity mismatch, damage, missing safety information, uncertain inspection or examination status, wrong attachment, unsuitable ground, unavailable rescue arrangements or unverified operator competence.

Completion and hand back: Park and secure through the agreed method, record condition and defects, prevent further use where held, and complete a joint handover to the supplier or site owner.

Evidence: Hire specification, delivery and acceptance record, applicable inspection or examination evidence, operator authorisation, daily checks, defect history and return handover.

Other interfaces: A hired saw remains quarantined when its guard or extraction is missing; a warehouse vehicle is held when pedestrians cannot be segregated; a modified conveyor returns to service only after the guarding, isolation and operating controls are checked by the authorised owner.

Guard interlock fails before production

Task material and setting: Guarded production machine. The user’s prescribed check finds that the guard interlock does not achieve its intended protective function.

People and prerequisites: Authorised user, supervisor, competent maintainer and operating owner; equipment-specific instructions, all-energy control and defect route.

Before: Stop the task and prevent unintended use through the approved equipment-specific method; notify the supervisor and competent maintainer.

During: Keep production on hold. Only authorised competent people investigate or test under the agreed safe system; operators do not bypass safeguards or use production as a test.

Hold or stop: Unknown cause, failed protection, unverified energy state or incomplete test evidence prevents return to use.

Completion and hand back: Competent repair and validated safeguard tests demonstrate the intended function; required inspection/change review is complete. The operating owner records release and briefs affected users before production.

Evidence: Defect/event report, energy-control handback, repair or investigation record, safeguard test results and named operating release.

Emergency stop activated: reset does not release production

Task material and setting: Guarded production machine. An unexpected machine response prompts an emergency stop. The reason and safe energy state remain unresolved.

People and prerequisites: Authorised user, supervisor, competent maintainer and operating owner; equipment-specific instructions, all-energy control and defect route.

Before: Stop the task and prevent unintended use through the approved equipment-specific method; notify the supervisor and competent maintainer.

During: Keep production on hold. Only authorised competent people investigate or test under the agreed safe system; operators do not bypass safeguards or use production as a test.

Hold or stop: Unknown cause, failed protection, unverified energy state or incomplete test evidence prevents return to use.

Completion and hand back: The cause is understood, the machine and safeguards are verified and any required controlled commissioning is accepted. Resetting the stop alone is insufficient. The operating owner records release and briefs affected users before production.

Evidence: Defect/event report, energy-control handback, repair or investigation record, safeguard test results and named operating release.

What do the acronyms and key terms mean?

Use these terms consistently when selecting, using, inspecting, isolating and returning equipment to service.

TermMeaningBoundary
Work equipmentMachinery, appliance, apparatus, tool or installation used at work.Scope depends on real use.
GuardPhysical barrier preventing or restricting access to danger.Design is equipment specific.
Protection deviceControl or sensing function that reduces risk.Must not be bypassed.
Emergency stopAdditional rapid stop function where appropriate.Not full isolation.
IsolationSeparation and control of all relevant energy.Includes stored energy.
InspectionCompetent check to detect safety-relevant deterioration or installation issues.Not the same as maintenance.
QuarantineState preventing further use pending decision.Release needs evidence and authority.
Return to serviceRecorded operational acceptance after restoration.Repair alone is insufficient.
PUWERProvision and Use of Work Equipment Regulations; GB 1998 and NI 1999 are separate instruments.Covers workplace selection, use, maintenance and safeguards.
LOLERLifting Operations and Lifting Equipment Regulations; separate GB and NI instruments.Additional duties for lifting equipment and operations.
ACOPApproved Code of Practice: guidance with special legal status under the relevant regime.Check edition, approval and jurisdiction.
UKCA, CE and UKNIProduct conformity markings used in different GB or NI supply routes.A mark does not prove suitability or safe workplace use.
HSE and HSENIHealth and Safety Executive for Great Britain and Health and Safety Executive for Northern Ireland.Follow the jurisdiction-specific duty route.
RPE and PPERespiratory protective equipment and personal protective equipment.Residual protection only where a task needs it; never a guard substitute.
ERICPDEliminate, Reduce including substitution, Isolate, Control, personal protective equipment, Discipline.A SHARE decision prompt; sustain effective controls and learning.
PPEPersonal protective equipment.Use for assessed residual exposure; it does not replace stronger feasible controls.

Practise the checks in 3D

Follow the highlighted check, compare a sound part with a fault, and see how a missed fault can cause harm. Then use the matching blank checksheet to record what you actually find.

Browse all 25 checksheets and 26 demonstrators

Documents to download

Download editable resources from the SHAREhub environment to support your work. Working forms and spreadsheet input areas are blank. Reports, plans, guides, briefings, procedures and policies contain completed fictional example content to adapt.

Return to SHARE home