SHARE Knowledge Hub

Electricity at work

Electricity can kill or severely injure through shock, arcing, burns or fire, and construction work adds changing supplies, damaged tools and hidden services. Control starts before work: identify energy sources and exposed people, avoid live contact, choose suitable equipment, and secure isolation when work is needed. Check the controls at the workface and stop when the supply or service route is uncertain.

Updated 2026-10-22UK focusConstructionElectrical safety

Understanding Electricity at work

Electricity can kill or severely injure through shock, arcing, burns or fire, and construction work adds changing supplies, damaged tools and hidden services. Control starts before work: identify energy sources and exposed people, avoid live contact, choose suitable equipment, and secure isolation when work is needed. Check the controls at the workface and stop when the supply or service route is uncertain.

Why this matters at work

Process failure: Dutyholder relies on generic policy or contractor label | How control is lost: No-one verifies system suitability, work control or changed conditions | Possible consequence: Exposure to electrical danger, injury, enforcement and repeat failure | Management measures assurance and recovery: Avoid: stop unplanned work; Limit scope: limit operation and access; Restrict release: isolate/segregate; Management arrangements: risk assessment, role allocation, coordination, competence and assurance; Residual task protection: task PPE; Implementation assurance: dutyholder checks that named competent owners implement the duty map, contractor interfaces and field controls.

Process failure: Controls are not reviewed after change or warning signal | How control is lost: Earlier assumptions about system, environment, people or barriers become invalid | Possible consequence: Shock, fire, outage, repeat incident and enforcement | Management measures assurance and recovery: Avoid: stop unknown/unsafe use; Limit scope: restrict state/exposure; Restrict release: isolate/segregate asset; Management arrangements: change management, inspection, consultation, action ownership and audit; Residual task protection: residual PPE; Implementation assurance: assurance owner checks changed assumptions, action evidence and field effectiveness before accepting closure.

How organisations manage this in practice

EAWR requires systems to be maintained so far as reasonably practicable to prevent danger. Maintenance is a managed process, not a sticker. It should reflect equipment type, environment, pattern of use, movement, age, damage history, safety consequence and manufacturer's information. Visual examination finds many defects; some faults can only be found by testing. Testing alone cannot reveal every visible, use-related or environmental defect, so user checks, formal visual inspection, appropriate testing, repair control and management review work together.

Under CDM, relevant electrical information should be considered during pre-construction planning and transferred into design risk management, contractor selection, the construction phase plan, induction, coordination and the health and safety file where applicable. Clarify who controls the existing installation and the temporary system, who may make changes, who holds keys or isolation authority, how equipment is registered, where cable routes are permitted, how defects are reported and how systems will be inspected, commissioned and decommissioned.

Review the arrangements after a new/altered installation, construction phase change, changed process or cleaning method, water/weather event, collision, new contractor, equipment/supply change, repeated defect, fire/smoke, electric shock, service strike, enforcement action or evidence that workers work around the intended control. Update drawings, assessments, procedures, inductions, inspection plans, emergency information and related source records before routine work resumes.

Start with the changing construction workface

For the crane route, the site manager coordinates the line owner and lifting planner before plant enters the affected area. Changed reach, ground level, weather or line information reopens that decision. For the digging route, the supervisor and competent locator resolve discrepancies with the service owner before intrusive work.

Contact can connect electrical energy to people

Contact can connect electrical energy to people. Three linked stages with matched controls and an evidence check.
Previous indoor use and a test sticker do not establish suitability for a changed environment.
Full written explanation
  1. Electrical source. Supplies, equipment, overhead lines and buried cables may affect the task.
  2. Contact or equipment failure. Damage, unsuitable conditions, reach or ground disturbance can create an exposure route.
  3. Shock, burns or fire. An old test label or an RCD does not remove every electrical hazard.

Change the pathway

  • Avoid the exposure. Design the task and route to avoid electrical danger where practicable.
  • Use suitable equipment and systems. Match supplies, protection and maintenance to the actual environment.
  • Control defects and changes. Remove defective equipment from use and obtain competent advice for uncertain boundaries.

Evidence check: Previous indoor use and a test sticker do not establish suitability for a changed environment.

Open the complete HD image (new tab)Download image

Keep each release tied to its workface and current conditions. An unknown conductor, altered plant position or damaged temporary supply triggers a stop and reassessment even if the morning briefing and permit were complete.

Content amended 19 October 2026 by the SHARE Knowledge Hub editorial team. This records an editorial content change; the existing technical-review and approval status still applies.

Reassess temporary supplies and the plant route

On a construction site, temporary boards, trailing cables, overhead lines and uncertain buried services can create different exposure routes as the work changes.

Reassess electricity as the workface changes

Reassess electricity as the workface changes. Four connected checks with a shared hold condition, responsible roles and two workplace examples.
Previous indoor use and a test sticker do not establish suitability for a changed environment.
Full written explanation
  1. Identify the sources. Consider the equipment, supplies and any overhead or buried services affected.
  2. Assess the actual conditions. Review location, moisture, damage, plant reach, ground levels and changing work.
  3. Provide appropriate controls. Use suitable equipment and competent electrical/isolation arrangements for the task.
  4. Inspect and respond. Act on defects and changed evidence; maintain the planned separation and work boundary.

When the evidence does not fit: Visible damage, an uncertain electrical boundary or an unsuitable setup: stop the affected use and obtain competent resolution.

Who acts: Employer and work planner, competent electrical people and relevant service/line owners.

Changed workplace

Temporary construction work: Boards, cables, plant routes and services change as the project develops.

Office or warehouse equipment: Check actual condition and use; earlier testing does not override damage seen today.

Evidence check: Previous indoor use and a test sticker do not establish suitability for a changed environment.

Open the complete HD image (new tab)Download image

Electrician checking a locked-off UK electrical isolator. Photorealistic illustration.
Illustrative UK workplace scene. Read the practical checks below for responsibilities, evidence and limits. Download image · Download smaller image
  1. Plan the supply

    Use suitable competent arrangements for distribution, environment, protection and inspection of temporary equipment.

  2. Plan the movement

    Review plant reach, delivery/access routes and cable protection, including overhead and buried services.

  3. Stop on uncertainty

    Hold affected work where service identity, position or protection is unresolved and obtain competent reassessment before release.

No clearance distance or excavation method can be taken from this conceptual site plan.

What is the safe sequence for construction electricity?

Identify the source, workface and people exposed; avoid the line or circuit; protect and isolate what remains; then verify the method before and during work.

What is the safe sequence for construction electricity?

What is the safe sequence for construction electricity?. Relationship map from the current topic. HSE guidance addresses GB practice; apply the corresponding NI instrument to NI workplaces and verify the actual task.
Learning point: Relationship map from the current topic. HSE guidance addresses GB practice; apply the corresponding NI instrument to NI workplaces and verify the actual task.
Read the complete visual as text
  1. Identify the source, workface and people exposed; avoid the…: Identify the source, workface and people exposed; avoid the line or circuit; protect and isolate what remains; then verify the method before and during work.
  2. A change to the excavation, temporary supply or weather…: A change to the excavation, temporary supply or weather can defeat a plan made that morning. The supervisor should compare drawings with field conditions, assign an isolation lead and stop when an unknown conductor or service appears.

A change to the excavation, temporary supply or weather can defeat a plan made that morning. The supervisor should compare drawings with field conditions, assign an isolation lead and stop when an unknown conductor or service appears.

Temporary electrical supplies: follow the path to shock and fire: illustrative 3D equipment and the people who may be affected
Interactive 3D explainerSHAREsim

Temporary electrical supplies: follow the path to shock and fire

Explore how this equipment can harm its users and other people, then follow the practical measures that interrupt each pathway. This is a hazards and good-practice lesson; the separate checklist remains the pre-use/safety-check activity.

Hazards and good practice: learn what can hurt people during use, change and maintenance. Pre-use and safety checks stay in the separate checklist.

Checksheets and risk assessments

Equipment checksheets

Risk assessment examples

Full written walkthrough — all 8 steps
  1. 1. Plan a suitable supply and work setting

    What is happening: The distribution unit connects a source, protective devices, cables and equipment in a changing workplace.

    How harm can occur: Unsuitable equipment or arrangements can expose users and other trades to shock, burns, arc or fire.

    Best practice to apply: Use competent design and selection for the actual work, supply and environment; reduce avoidable electrical exposure.

    Why this works: Suitable selection controls the hazard before a person has to work near the system.

    Electrical hazards and risks · How should an electrical hazard be traced?
  2. 2. Understand the contact pathway

    What is happening: A live part or fault can connect the supply through a person to another conductive surface.

    How harm can occur: Current through the body can cause serious injury; arcing can cause burns without the same direct contact.

    Best practice to apply: Keep live parts enclosed and inaccessible and use the actual protective arrangements; never open this example as a user instruction.

    Why this works: Preventing access interrupts contact; appearance and a healthy-looking cable do not establish an electrically safe system.

    Electrical hazards and risks · Separate contact, arc, ignition and secondary injury
  3. 3. Protect cables in the real work route

    What is happening: Leads cross areas where vehicles, sharp edges, water and other operations may affect them.

    How harm can occur: Damage or unsuitable routing can expose conductors, start a fire or create a trip leading to secondary injury.

    Best practice to apply: Use appropriate routing and mechanical/environmental protection and respond to damage without makeshift live repairs.

    Why this works: The route is part of the electrical risk, even when the connected tool has no visible defect.

    Electrical hazards and risks · Why do wet environments increase electrical risk?
  4. 4. Keep protective functions in context

    What is happening: An RCD is one protective measure within a complete system, not permission to use a damaged supply.

    How harm can occur: Some faults, contact conditions and other hazards are not removed simply because an RCD is fitted.

    Best practice to apply: Use suitable competent selection, installation and verification; retain other required protection and the instructed user checks.

    Why this works: A single protective device cannot stand in for correct system design and continued condition.

    Electrical hazards and risks · How can the hierarchy of controls reduce risks while using portable power for a site repair?
  5. 5. Maintain enclosure and access boundaries

    What is happening: The sealed cover separates users from internal components and keeps the operating interface distinct.

    How harm can occur: Opening or defeating protection can create access to energy that a routine user cannot safely assess.

    Best practice to apply: Keep covers and restricted areas secure; refer faults or access needs to the responsible competent electrical person.

    Why this works: Routine operation and intrusive electrical work require different competence and control arrangements.

    Electrical hazards and risks · What training and competence are needed for electrical hazards?
  6. 6. Recognise stop and isolation as different actions

    What is happening: A switch indication or an inactive tool does not identify every source of electrical or other stored energy.

    How harm can occur: A backup, battery, control circuit or other source can cause unexpected energisation or movement.

    Best practice to apply: Plan dead work through the actual competent isolation, securing and verification procedure; this lesson does not teach live testing.

    Why this works: System-specific identification and verification address sources that a simple stop can leave present.

    Electrical hazards and risks · How can electricity injure the body, and why can a small mark hide a serious incident?
  7. 7. Deal with an unsafe condition without touching danger

    What is happening: A damaged supply or casualty may still be connected to continuing electrical danger.

    How harm can occur: A rescuer or colleague can become a second casualty by approaching or touching too soon.

    Best practice to apply: Keep people clear, use the site's emergency arrangements and have the continuing danger controlled; do not improvise a repair or rescue contact.

    Why this works: Preventing additional contact protects people while competent emergency help and isolation are arranged.

    Electrical hazards and risks · What are the secondary effects of electrical incidents?
  8. 8. Return equipment only after competent resolution

    What is happening: A replaced cable or reset trip does not by itself explain the fault or prove that the installation is suitable.

    How harm can occur: The same fault can recur and harm the next user or an adjacent trade.

    Best practice to apply: Record and restrict defective equipment, resolve the cause and have the necessary verification and handover completed.

    Why this works: A verified repair and clear restrictions prevent a temporary reset being mistaken for a safe hand-back.

    Electrical hazards and risks · How can the hierarchy of controls reduce risks while using portable power for a site repair?

Illustrative awareness learning. Geometry, colours and movement do not establish safe distances, capacity, exposure, isolation or work permission. Use the actual assessment, equipment information and competent arrangements.

The wider workplace has its own account and subscription access. Exploring this lesson does not grant access, record course completion or authorise work.

UK guidance for further reading

HSE: Temporary electrical supplies
SHAREsimulate

How can I practise this topic in 3D?

A temporary generator has an improvised supply
3D workplace practiceSHAREsim

A temporary generator has an improvised supply

All related inspection points 2 across 1 location
Construction site 2 inspection points

Practice in the SHAREhub environment. Browser practice is separate from workplace competence and formal learning records.

What are the key points about electricity?

The key points are that electricity is invisible, fast-acting, often high consequence and heavily affected by site conditions.

Electricity can kill instantly

Shock can affect the heart, breathing and muscle control, and can cause falls or secondary injury.

Construction changes the risk

Temporary layouts, weather, plant movement and multiple contractors make controls harder to maintain.

Portable equipment needs active management

Pre-use checks and defect removal are often more valuable than relying only on testing stickers.

Overhead and buried services are critical hazards

The electrical source may not be visible until plant, excavation or drilling enters the danger zone.

Isolation must be verified

Switching off is not enough for electrical work; secure isolation and proof dead are essential.

Evidence should match the risk

Good records include service plans, permits, inspections, briefings, defect logs and action close-out.

What does electricity mean as a workplace health and safety topic?

Electricity as a safety topic means controlling electrical energy so it cannot injure people, start fires or disrupt essential systems.

Electricity should be understood as an energy hazard. It may be fixed in a building, distributed through temporary site supplies, carried by overhead or underground services, stored in batteries, used in tools or controlled through machinery and switchgear. The hazard becomes risk when people can touch live parts, equipment faults, cables are damaged, protective systems fail or work is planned without knowing where live services are.

The practical management question is not simply 'is electricity present?' Electricity is present almost everywhere. The useful question is: where could electrical energy escape normal control, who could be exposed, what makes injury severe, what controls prevent contact or ignition, and how does the site know those controls are working today?

Construction and refurbishment deserve particular care because the workface moves. A route that was clear yesterday may contain a temporary cable today; an excavation may reach a service that was missing from drawings; a mobile crane may work closer to overhead lines as ground levels change.

Electricity risk pathway - Electricity risk pathway
Stage Question Example
Source Where is electrical energy present? Temporary board, overhead line, charger, tool, hidden cable or switchgear.
Exposure How could someone contact it? Damaged lead, wet tool, drilling, excavation or plant contact.
Severity What makes the outcome worse? Wet conditions, height, high voltage, rescue difficulty or flammable atmosphere.
Controls What prevents exposure? Isolation, RCDs, reduced voltage, cable protection, barriers and competence.
Evidence What proves the controls work? Inspection records, permit checks, service drawings and defect closure.

What harm can electricity cause?

Electricity can cause electric shock, burns, arc injury, fire, explosion, loss of muscle control and secondary injury.

Electric shock can disrupt heart rhythm, stop breathing, cause muscle contraction or prevent someone letting go. A worker shocked while on a ladder, scaffold, MEWP or roof may fall. Electrical burns may be deep because current heats tissue internally, and arc events can cause severe burns, eye damage, hearing damage and fire.

Electrical fires can start when cables are overloaded, plugs are loose, equipment overheats, chargers are damaged or protective devices are wrong. Where flammable substances are present, sparks or hot surfaces can become ignition sources.

Electrical harm overview - Electrical harm overview
Harm How it happens Workplace example
Shock Current passes through the body. Worker touches damaged live cable.
Burns Contact or arc energy damages skin and deeper tissue. Fault inside a distribution board.
Fall Shock causes loss of balance or muscle control. Worker shocked while using a ladder.
Fire Overload, loose connection or damaged charger overheats. Extension lead under site cabin desk.
Explosion Electrical ignition source meets flammable atmosphere. Charging or hot work near vapour release.
Service disruption Cable strike or electrical fault cuts critical supply. Excavator damages incoming electrical service.
How can electricity injure the body, and why can a small mark hide a serious incident?
Interactive 3D anatomySHAREsim

How can electricity injure the body, and why can a small mark hide a serious incident?

Interactive anatomy · Electrical injury · Updated 2026-10-23

Electrical injury terms

A broad term for injury associated with electrical exposure.

An external current affecting the body.

Tissue injury caused by electrical heating.

Death from electric shock.

Health and Safety Executive: Electrical injuries · Health and Safety Executive: Selection and use of electric handlamps, PM38 · NHS: Burns and scalds
Read all anatomy and process explanations without the viewer

General occupational awareness of anatomy and incident mechanisms. A broad term for injury associated with electrical exposure. An external current affecting the body. Tissue injury caused by electrical heating. Death from electric shock. Electrical rescue, live testing, isolation or energised work instruction An energise-person control, contact timer, voltage or resistance input Safe current paths, survival percentages or shock-severity scores ECG interpretation, rhythm selection or AED shock decisions Medical or workplace clearance from a mark, diagram or feeling well The hazard-avoidance and medical-help panel is visible before model loading and quiz completion.

Nerve pathway

Nerves communicate using electrical and chemical signals. Nerves carry biological signals, and communication at the nerve-to-muscle connection helps activate muscle. The travelling cue is a simplified way of directing attention to that relationship. It does not show household current circulating through a person, and its colour, speed or brightness cannot be used to interpret nerve function or electrical injury. Alder Hey Children’s NHS Foundation Trust: Nerve service — normal nerve function · NHS: Lambert-Eaton myasthenic syndrome — normal nerve-to-muscle signalling · Oxford University Hospitals NHS Foundation Trust: Nerve Conduction Studies and Electromyography

Skeletal muscle

The nervous system normally coordinates muscle contraction. A slow hand movement demonstrates normal function; it does not imitate a casualty’s involuntary movements. Alder Hey Children’s NHS Foundation Trust: Nerve service — normal nerve function · NHS: Lambert-Eaton myasthenic syndrome — normal nerve-to-muscle signalling

Breathing muscles

Coordinated muscle activity helps move air into and out of the lungs. The diaphragm and chest movement belong to the respiratory lesson. This example shows no breathing-rate measurement. Cambridge University Hospitals NHS Foundation Trust: Breathing pattern disorders and physiotherapy — normal diaphragm role

Heart conduction

Coordinated electrical activity helps organise the heart’s pumping. A labelled sequence illustrates normal biological activation. It is not an ECG or a rhythm-interpretation exercise. St George’s University Hospitals NHS Foundation Trust: Catheter Ablation for Supra-Ventricular Tachycardia — normal electrical system · NHS 111 Wales: Cardiac Arrest

Skin contact region

Contact conditions influence how an electrical exposure affects the body. The marker identifies an example contact region. It does not calculate skin resistance or identify a safe point to touch. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Electrical safety frequently asked questions

Internal tissue region

Electrical injury can extend beneath the visible surface. An electrical incident can cause effects below the surface, so visible appearance alone cannot describe the whole injury. This transparent region marks the subject of the explanation, rather than a measured boundary of damage. Its shape does not establish where current travelled or which tissues are unaffected; compare it with the selected mechanism caption. Health and Safety Executive: Electrical injuries · NHS: Burns and scalds · NHS 111 Wales: Burns and scalds — electrical burns

External source

The incident hazard comes from an electrical source outside the body. The generic equipment symbol is kept disconnected from the normal biological signalling diagram. Health and Safety Executive: Introduction to electrical safety

Illustrative exposure route

This broad region represents one possible exposure route. It cannot establish the actual route or outcome. There is no safe-path selector, voltage control or timed-contact exercise. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Electrical safety frequently asked questions

Arc and thermal region

An arc or hot electrical equipment can cause injury. This separate incident panel is different from a simple through-body current diagram. No arc flash is animated. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Introduction to electrical safety

Secondary injury

Loss of control can lead to falls or contact with nearby hazards. The neutral surrounding-hazard symbol recognises these injuries without staging a fall or body jerk. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Introduction to electrical safety

Response boundary

Keep clear of unresolved electrical danger and get emergency help. Do not touch a person who may still be in contact with an electrical source. This node opens the safety panel, never a rescue activity. Health and Safety Executive: Introduction to electrical safety · Health and Safety Executive: Electricity — electric shock and overhead-line precautions · Health and Safety Executive: Emergency procedures

Open the complete process transcript

The process, step by step

Explore normal function

Start with the body’s own signalling: nerves communicate with muscles, breathing muscles move the chest, and organised activation coordinates the heart. Select one example at a time and read the associated label before changing systems. These are normal biological functions, not electricity from equipment moving through a person. The slow cues make the explanation easier to follow; they do not show a measured nerve signal, breathing rate or heart rhythm. This process sequence is a teaching route through the subject, not a simulation of an electrical accident. Alder Hey Children’s NHS Foundation Trust: Nerve service — normal nerve function · NHS: Lambert-Eaton myasthenic syndrome — normal nerve-to-muscle signalling · Cambridge University Hospitals NHS Foundation Trust: Breathing pattern disorders and physiotherapy — normal diaphragm role · St George’s University Hospitals NHS Foundation Trust: Catheter Ablation for Supra-Ventricular Tachycardia — normal electrical system

What to watch: Select the nerve, skeletal-muscle, breathing-muscle and heart labels individually, noticing that each belongs to a different normal biological example.

Why it matters: Normal signalling helps muscles work in a coordinated way. Keeping these biological examples distinct from the incident diagrams makes it easier to explain what an external electrical hazard can disrupt.

Explore this step: Explore one normal system, then explain its function before selecting a different system.

Locate the external hazard

Locate the generic electrical-source symbol outside the body and compare it with the normal biological labels. It represents an external workplace hazard, not the source of ordinary nerve or heart signalling. The model keeps the equipment symbol separate and does not energise the silhouette when a learner selects it. This step establishes the context before the different injury mechanisms are discussed. A picture of equipment cannot show whether real equipment is safe. Use the label to identify the distinction, rather than imagining that the model is testing a circuit. Health and Safety Executive: Introduction to electrical safety · Health and Safety Executive: Emergency procedures

What to watch: Locate the external-source symbol and the response-boundary label, then compare their positions with the normal body-system labels.

Why it matters: An external electrical supply is a hazard that requires competent control. Separating it from biological signalling avoids implying that a normal nerve pathway describes a safe route for electrical current.

Explore this step: Identify which labels describe the body and which identify the external hazard or safety boundary.

Choose an incident example

Choose one incident explanation: electric shock, electrical heating within tissue, or an arc and its thermal effects. These are different mechanisms and more than one may be relevant to an incident. Read the selected heading before examining the highlighted region so that the image and explanation remain connected. The model is a route through the concepts, not a calculation of current flow or injury severity. It provides no voltage control, safe-contact experiment or animated arc. Compare the labels to explain how the mechanisms differ without ranking an actual casualty’s injuries. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Introduction to electrical safety

What to watch: Read the incident heading, then locate its contact, internal-tissue or arc-and-thermal label rather than combining every marker into one route.

Why it matters: Shock can disturb body function, while heating can injure tissue. An arc can cause thermal injury without being equivalent to the simple contact diagram; the examples can overlap in a real incident.

Explore this step: Compare two incident panels and describe the different mechanism named by each heading.

Explain possible effects

Read the caption beside the selected system and trace the labelled relationship being explained. Electric shock can interfere with muscle control, breathing or the way the heart beats; electrical heating can damage tissue. The highlighted region is a teaching focus, not a map of an individual’s injury. It cannot identify the actual route through the body or declare that an unhighlighted organ is unaffected. Compare the normal-function labels with the incident caption, keeping the possible effect separate from any claim about what has happened to a particular person. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Electrical safety frequently asked questions

What to watch: Compare the breathing-muscle, heart and internal-tissue labels with the caption for the incident mechanism currently selected.

Why it matters: Interference with coordinated muscle or heart function can be serious even when an illustration shows little surface change. A teaching marker cannot determine which effects are present or absent in a real person.

Explore this step: Choose a system and describe its normal role before reading the possible effect in the incident caption.

Know the limits

Finish by comparing the questions the diagram answers with those it cannot answer. It can introduce normal signalling and distinguish several possible injury mechanisms. It cannot establish an actual exposure, the extent of damage, a safe electrical condition or medical clearance. A small-looking electrical burn or feeling well does not provide that clearance. The external-source and response-boundary labels keep these limits visible. Review them alongside the existing safety panel; completing this teaching route is not a rescue procedure, a clinical assessment or permission to resume the work. NHS: Burns and scalds · Health and Safety Executive: Electrical safety frequently asked questions · NHS 111 Wales: Burns and scalds — electrical burns

What to watch: Locate the internal-tissue and response-boundary labels, then compare the limits stated in their captions with the incident explanation.

Why it matters: Visible appearance alone cannot establish the seriousness of electrical injury. Keeping the model’s scope clear prevents an explanatory picture or completed activity being mistaken for evidence that a person or workplace is safe.

Explore this step: Name one question the model explains and one question that requires assessment beyond this teaching view.

Mechanisms and their limits

Electric shock: disruption of normal function External electrical current can interfere with muscle control, breathing or the heart’s organised activity. These are possible effects; the same diagram cannot predict the outcome of a real incident. An illustrative route does not show that a particular organ must or cannot be affected. No arbitrary arrhythmia, dramatic flatline, body jerk or calculated survival result is shown. Both alternating and direct current can be dangerous. The viewer offers no safe voltage or safe path. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Electrical safety frequently asked questions

HSE: prevent electrical injury

HSE: effects and uncertainty

Electrical heating: injury beneath the surface Current passing through tissues can generate heat and cause burns beneath the skin. A small visible mark is not enough to judge the internal effects. Not every shock produces extensive burns. The marked region is illustrative, not a reconstructed path, calculated burn depth or severity score. An electrical burn needs emergency medical assessment even if it appears small. Feeling well or selecting a similar image does not provide workplace or medical clearance. Health and Safety Executive: Electrical injuries · NHS: Burns and scalds · NHS 111 Wales: Burns and scalds — electrical burns

NHS: electrical burns need emergency care

HSE: electrical injury mechanisms

Arc, heat and secondary injury Arcing and hot electrical equipment can injure people without the event fitting a simple hand-to-foot contact story. Heat, fire or explosion and secondary falls or nearby machinery may add hazards. The diagram does not require a through-body route to recognise an arc or thermal hazard. Alternating and direct current equipment can both present hazards. This is an incident explanation, not a flash-energy calculation or permission to approach damaged equipment. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Introduction to electrical safety · Health and Safety Executive: Electrical safety frequently asked questions

HSE: electrical hazards and controls

HSE: competent assessment of unsafe equipment

Electric shock: disruption of normal function — follow the anatomy

Look at: The contact route through the body, including nerves and muscle.

What changes: Electric current can interfere with normal nerve, muscle, breathing or heart activity.

Why it matters: A person may be unable to let go, collapse or develop a dangerous rhythm.

What to do: Keep clear, do not touch anyone still in contact with electricity, call 999 and follow competent site emergency arrangements.

Damaged portable equipment presents an unresolved electrical hazard

A worker finds damaged equipment near a damp work area; the exposure is a counterfactual failure of controls, not a rescue exercise. An acute incident is explained in 32 seconds without voltage, current or contact-duration inputs. The sequence sets no safe exposure or waiting time. Never touch a person or equipment while electrical danger is unresolved. The viewer cannot prove isolation or infer the actual current path or outcome.

Keep clear of the unresolved source Damaged equipment in a damp area is a stop-and-report situation. Do not touch a potentially live casualty; call appropriate help and use competent site emergency arrangements. Health and Safety Executive: Electrical safety frequently asked questions · Health and Safety Executive: Emergency procedures

What failed barriers could allow The counterfactual contact example marks an external source and possible exposure. It does not ask the learner to energise a person or select a supposedly safe route. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Electrical safety frequently asked questions

Possible interference with normal function External current can affect muscle control, breathing or heart function. These are possible effects, not a prediction that every organ is involved or that a particular contact is survivable. Health and Safety Executive: Electrical injuries

Safety first, then urgent assessment Keep clear and obtain emergency help while danger remains. Only once the scene is safe does the separate unresponsive/abnormal-breathing CPR/AED guidance apply. Feeling well does not provide medical or equipment clearance. Health and Safety Executive: Electrical safety frequently asked questions · NHS: Burns and scalds · NHS 111 Wales: Cardiac Arrest · Health and Safety Executive: Emergency procedures

Electrical heating: injury beneath the surface — follow the anatomy

Look at: The tissue beneath the electrical contact points.

What changes: Current can generate heat inside the body as well as at the skin.

Why it matters: A small visible mark can conceal serious deeper injury.

What to do: Keep the scene safe; electrical burns need 999 or A&E assessment even when the visible mark is small.

A small external mark after an electrical incident

After an electrical incident, a worker has a small visible hand mark; the area must be made safe by competent arrangements. This is a possible injury explanation, not a burn-depth model or a simulation of tissue heating at a selected exposure time. Visible marks cannot establish the route or depth of internal injury. Not every shock produces the broad affected area used in this illustration.

Do not approach unresolved energy danger The incident is treated as an electrical emergency until the scene is safe. Keep clear, summon appropriate help and do not judge safety from a small mark. Health and Safety Executive: Electrical safety frequently asked questions · NHS: Burns and scalds

External current can heat tissues A broad translucent region represents possible tissue heating during contact. It is not a wire tracing the real route and it does not calculate dose from a contact point. Health and Safety Executive: Electrical injuries

An external mark may understate injury The selected region separates possible internal effects from the skin marker. Size or appearance of the mark cannot clear the person or tell the learner what tissues were actually injured. Health and Safety Executive: Electrical injuries · NHS 111 Wales: Burns and scalds — electrical burns

Arrange medical assessment Use emergency help for electrical burns and follow live advice once it is safe to assist. Do not continue work or reassure someone simply because the mark is small; the activity gives no treatment or return-to-work clearance. NHS: Burns and scalds · NHS 111 Wales: Burns and scalds — electrical burns · Health and Safety Executive: Emergency procedures

Arc, heat and secondary injury — follow the anatomy

Look at: The skin and eyes facing the arc, and the worker’s surroundings.

What changes: An electrical arc releases intense heat; the event may also cause a fall or other trauma.

Why it matters: Burns and secondary injuries can occur without a current path through the body.

What to do: Control arc hazards, use competent isolation procedures and plan emergency response.

An electrical fault releases heat near a work area

A fault or overheated electrical component exposes people nearby to heat and possible secondary hazards. The short explanation omits flashes, noise and blast effects. It predicts no arc boundary, burn depth, safe distance or survival probability. Arc/thermal injury is separate from the through-body current example. A person need not supply a hand-to-foot contact story for the incident to be serious.

Treat the fault as unresolved danger Keep clear of faulty or overheated equipment and activate competent emergency arrangements. The example gives no permission for live inspection or repair. Health and Safety Executive: Introduction to electrical safety · Health and Safety Executive: Electrical safety frequently asked questions · Health and Safety Executive: Emergency procedures

Heat can be released without the chosen contact route The equipment-and-person schematic marks hot material or thermal exposure. No bright flash or energise-person action is used to teach the incident. Health and Safety Executive: Electrical injuries · Health and Safety Executive: Introduction to electrical safety

Possible thermal and secondary injury Heat may injure tissue, and a loss of control or sudden movement may lead to falls or contact with surrounding hazards. These possibilities remain separate from a reconstructed internal current path. Health and Safety Executive: Electrical injuries

Control the danger and get help Follow site emergency arrangements and obtain medical help for injuries once safe to assist. Competent investigation must address the fault; no visual improvement in the model clears the equipment or the worker. NHS: Burns and scalds · Health and Safety Executive: Electrical safety frequently asked questions · Health and Safety Executive: Emergency procedures

Read the practice situations and all answer explanations
EL-Q1: What can be concluded from the mark?

A colleague has had an electrical incident and has only a small visible mark.

It proves the event was harmless. — A small mark cannot rule out internal effects. Electrical burns need emergency care.

Internal effects cannot be judged from the mark; seek appropriate medical assessment. — Correct. Do not use appearance as reassurance. Keep the area safe and obtain appropriate medical help; an electrical burn requires 999 or A&E.

Select the closest route in the model to calculate survival. — The model cannot reconstruct the incident or predict survival. Seek appropriate help instead of matching an image.

Health and Safety Executive: Electrical injuries · NHS: Burns and scalds · NHS 111 Wales: Burns and scalds — electrical burns
EL-Q2: Which response avoids creating another casualty?

Someone may still be in contact with a live electrical source.

Touch them immediately to pull them away. — Do not touch them while the electrical danger is unresolved. You could also be injured. Call for emergency help.

Keep clear, call emergency help and follow competent site emergency arrangements. — Correct. Call 999 and explain that electricity is involved. Keep others clear and follow competent emergency arrangements; this lesson does not teach electrical rescue or isolation.

Use the viewer to find the safest current path. — There is no safe-path or rescue method in this viewer. Keep clear and get emergency help.

Health and Safety Executive: Introduction to electrical safety · Health and Safety Executive: Electricity — electric shock and overhead-line precautions · Health and Safety Executive: Emergency procedures
EL-Q3: What still needs consideration?

An arc incident happens without an obvious hand-to-foot contact route.

There cannot be an injury without that route. — A simple through-body route is not required for an arc/thermal injury or a secondary fall.

Arc, heat and secondary injuries. — Yes. Consider the incident hazards and obtain appropriate help rather than forcing the event into one current-path drawing.

Direct-current equipment cannot cause harm. — Both AC and DC equipment can be hazardous. Neither label provides reassurance.

Health and Safety Executive: Electrical injuries · Health and Safety Executive: Introduction to electrical safety · Health and Safety Executive: Electrical safety frequently asked questions
Sources and how the model is made

The opening images are AI-generated anatomical illustrations. The interactive 3D models and labelled SVG diagrams use original procedural artwork. These teaching images are not medical scans or diagnostic tools. Source references support the learner explanations and do not grant artwork rights.

· Three.js MIT licence

Why does construction increase electrical risk?

Construction increases electrical risk because the workplace is temporary, changing, weather-exposed and full of interfaces.

Construction electricity is not just about electricians. Groundworkers, plant operators, scaffolders, roofers, decorators, joiners, cleaners, delivery drivers and visitors can all be exposed by temporary supplies, overhead lines, buried cables, hidden wiring or portable tools. CDM-style planning should therefore identify electrical hazards before the work sequence is fixed.

The construction phase plan should show how temporary electrical supplies are installed, inspected, protected, modified and removed. It should also explain how overhead and underground services are identified, marked, avoided and supervised.

Construction electricity risk factors - Construction electricity risk factors
Risk factor Why it matters Control
Changing layout Cable routes and work areas move frequently. Daily inspection and protected routing.
Weather Rain and mud increase shock and equipment damage risk. Suitable equipment and RCD protection.
Multiple trades One trade can damage controls used by another. Coordination and briefings.
Temporary supplies Rapid installation can create weak routing or overload. Competent installation and inspection.
Live refurbishment Existing services may remain energised. Survey, isolation and permit control.
Plant movement Vehicles can strike cables or overhead lines. Segregated routes and exclusion zones.

For a Northern Ireland construction site, apply the NI CDM 2016 regulations to the construction-phase plan and project roles.

How should portable electrical equipment be managed?

Portable electrical equipment should be suitable, protected, checked before use, inspected by risk and removed from service when defective.

Portable equipment is exposed to knocks, dragging, vibration, damp, dust, heat and rough handling. A tool, charger or extension lead may pass a formal test but become dangerous after damage. That is why user checks matter: workers should look for cable cuts, exposed inner cores, cracked plugs, loose sockets, scorch marks, overheating, missing guards and signs of water ingress.

Inspection frequency should be risk-based. Site tools, extension leads and temporary equipment usually need more frequent checks than office equipment because the environment and use are harsher. Damaged equipment should be quarantined so it cannot be picked up by the next person.

Portable equipment controls - Portable equipment controls
Control What good looks like Evidence
Suitability Equipment matches voltage, environment and task. Procurement/specification record.
Pre-use check User checks visible damage before use. Briefing and observation.
RCD/reduced voltage Additional protection used where risk justifies it. Site electrical standard.
Formal inspection Competent checks at risk-based intervals. Inspection schedule.
Defect quarantine Damaged items cannot be reused. Defect log and tag.
Repair Repairs by competent people only. Repair record.

A label records a past test, not present fitness. The user checks the lead, plug, casing and conditions before use; damaged equipment is isolated and quarantined. A competent person sets the inspection and testing interval from use, environment and defect history. See HSE portable-appliance maintenance guidance.

How should temporary electrical supplies be controlled?

Temporary supplies should be designed, installed, protected, inspected and adapted by competent people as the site changes.

Temporary supply checks — part 1 of 2

Temporary supply checks — part 1 of 2. Compare the named situations, controls and evidence together. HSE guidance addresses GB practice; apply the corresponding NI instrument to NI workplaces and verify the actual task.
Learning point: Compare the named situations, controls and evidence together. HSE guidance addresses GB practice; apply the corresponding NI instrument to NI workplaces and verify the actual task.
Read the complete visual as text
  1. Distribution board location: Purpose: Avoid impact, water and unauthorised access. Weak signal: Board blocked, open or damaged.
  2. Cable route: Purpose: Prevent crushing, trips and water exposure. Weak signal: Cable across road or scaffold access.
  3. RCD test: Purpose: Confirms additional protection remains functional. Weak signal: No test evidence.

Temporary supply checks — part 2 of 2

Temporary supply checks — part 2 of 2. Compare the named situations, controls and evidence together. HSE guidance addresses GB practice; apply the corresponding NI instrument to NI workplaces and verify the actual task.
Learning point: Compare the named situations, controls and evidence together. HSE guidance addresses GB practice; apply the corresponding NI instrument to NI workplaces and verify the actual task.
Read the complete visual as text
  1. Loading: Purpose: Avoid overload and overheating. Weak signal: Daisy-chained extension leads.
  2. Lighting: Purpose: Provide safe access and emergency visibility. Weak signal: Dark routes or damaged lights.
  3. Change control: Purpose: Keep drawings/arrangements current. Weak signal: Ad hoc additions by trades.

Temporary electrical systems often become normal background noise on a site, but they are a key control. Distribution boards, leads, transformers, RCDs, generators, lighting and chargers should be planned to avoid traffic routes, wet areas, trip hazards, crushing, unauthorised alteration and overload.

Only competent people should install or modify temporary supplies. Site managers should make sure inspection keeps pace with site change: new cabins, altered access, additional plant, weather damage, relocated boards, temporary lighting and subcontractor equipment can all change the risk profile.

Temporary supply checks - Temporary supply checks
Check Purpose Weak signal
Distribution board location Avoid impact, water and unauthorised access. Board blocked, open or damaged.
Cable route Prevent crushing, trips and water exposure. Cable across road or scaffold access.
RCD test Confirms additional protection remains functional. No test evidence.
Loading Avoid overload and overheating. Daisy-chained extension leads.
Lighting Provide safe access and emergency visibility. Dark routes or damaged lights.
Change control Keep drawings/arrangements current. Ad hoc additions by trades.

How should work near overhead power lines be managed?

Work near overhead power lines should be avoided where possible and controlled through planning, consultation, exclusion zones and supervision where it cannot be avoided.

Overhead lines are especially dangerous because tall plant, cranes, MEWPs, scaffold tubes, ladders, tipper bodies and long materials can enter the danger zone before workers realise. Electricity can arc across air gaps at higher voltages, so direct contact is not always required.

Planning should start early. Options include diverting or isolating the line, designing the work away from it, setting safe routes, using barriers and goalposts, limiting plant height, briefing drivers and appointing supervisors who understand the line controls. Emergency instructions should tell people what to do if plant contacts a line.

Overhead line controls - Overhead line controls
Control Purpose Evidence
Avoid/divert/isolate Remove the line risk where reasonably practicable. Utility consultation record.
Exclusion zone Keep plant and people outside danger area. Site layout and briefing.
Goalposts/barriers Mark safe crossing points and routes. Installed barriers and inspection.
Plant limits Restrict height, reach or tipping where needed. Plant assessment and operator briefing.
Supervision Control high-risk activities near lines. Supervisor checks.
Emergency plan Controls contact scenario safely. Briefing and emergency procedure.

Move the work away from the line where possible. If plant must pass or operate nearby, the line owner and competent planner need to agree the route, clearance, barriers and supervision before lifting. A boom changing position or a new vehicle height is a stop and replan signal. See HSE GS6 overhead-line guidance.

How should work near underground power cables be managed?

Underground cable risk should be managed through information, locating, marking, trial holes, safe digging and stop-work rules.

Underground cables are hidden high-energy hazards. Drawings may be incomplete, inaccurate or out of date. Cables may be shallower than expected, poorly protected or routed through areas that look clear. Striking a live cable can cause burns, explosion, shock, fire and service disruption.

Safe digging follows a sequence: collect service information, inspect the site, use cable-avoidance tools correctly, mark the route, dig trial holes carefully, use safe hand-digging or vacuum/air methods near services and stop when conditions do not match the plan. Mechanical excavation should not be used blindly based on drawings alone.

Underground cable controls - Underground cable controls
Stage Control Evidence
Planning Collect utility plans and site information. Service pack.
Location Use CAT and signal generator by trained users. Locate record.
Marking Mark services clearly before digging. Marked site/photos.
Trial holes Expose services carefully to confirm position. Permit to dig.
Excavation Use safe digging methods near services. Supervisor inspection.
Unexpected findings Stop and reassess if services differ from plan. Change record.

A service drawing is a starting point, not proof of position. Compare records with a competent scan, mark the route, use the agreed safe digging method and keep mechanical tools out of uncertainty. Stop when plans, locator results or exposed services disagree. See HSE HSG47 underground-services guidance.

How should electrical isolation be managed?

Electrical isolation should disconnect, secure and verify electrical energy before work on electrical systems starts.

Switching equipment off is not the same as safe isolation. Electrical work should normally be done dead: identify the correct circuit, isolate, lock off, prevent re-energisation, prove the tester, prove dead, keep the isolation secure and reinstate only when the work area is safe and authorised.

Isolation planning should consider multiple supplies, generators, UPS systems, solar PV, control circuits and remote starts. If the person doing the work cannot prove what is dead and what remains live, the work should not start.

Isolation basics - Isolation basics
Step Purpose Evidence
Identify Confirm the correct circuit/equipment. Drawing and label check.
Isolate Disconnect at a suitable point. Isolation record.
Lock off Prevent reconnection. Lock/tag/key control.
Prove dead Verify the equipment is de-energised. Test confirmation.
Control work Keep the boundary understood. Permit or briefing.
Re-energise safely Restore only after checks and handback. Completion record.

How should electrical inspection and maintenance be organised?

Inspection and maintenance should be risk-based and should reflect equipment type, use, environment and defect history.

Electrical inspection should combine pre-use checks, formal visual inspection, testing where needed, fixed-installation review, temporary-supply inspection and defect close-out. The frequency should be higher where equipment is moved often, used outdoors, exposed to wet or dirty conditions, used by many people or damaged frequently.

A site with repeated damaged leads should not simply increase paperwork. It should ask why the leads are being damaged: poor routing, vehicle impact, unsuitable equipment, rushed work, poor storage, inadequate sockets or weak supervision.

Inspection layers - Inspection layers
Layer Typical focus Evidence
User check Visible damage before use. Worker briefing and observation.
Formal visual inspection Plugs, leads, casings, fuses and signs of overheating. Inspection record.
Electrical testing Earth continuity, insulation and other relevant tests. Test certificate.
Temporary supply inspection Boards, RCDs, routes, lighting and damage. Site electrical log.
Fixed installation inspection Condition of wiring and protective systems. EICR or equivalent record.
Defect close-out Unsafe equipment removed and repaired. Action tracker.

What emergency arrangements are needed for electrical incidents?

Emergency arrangements should explain how to isolate, keep rescuers safe, get first aid and prevent escalation.

In an electrical emergency, do not touch a casualty who may still be in contact with live electricity. Isolate the supply if it is safe to do so, keep others away, call emergency services where needed and provide first aid within competence once the scene is safe.

Sites should brief workers on contact with overhead lines, cable strikes, electrical fires, shock, burns and reporting. Operators of plant that contacts overhead lines need clear instructions: stay in the cab if safe, warn others away, call for help and only leave if there is immediate danger such as fire, using the correct jump-clear method.

Emergency scenarios - Emergency scenarios
Scenario Immediate priority Preparation
Shock from equipment Isolate before touching casualty. First aid and isolation briefing.
Cable strike Keep away and call utility/emergency support. HSG47 emergency instructions.
Overhead line contact Stay clear; plant may be energised. GS6-style briefing and exclusion.
Electrical fire Isolate if safe and use suitable response. Fire risk assessment.
Burns/arc injury Medical assessment and incident reporting. First aid cover.

How can the hierarchy of controls reduce risks while using portable power for a site repair?

Use HSE’s hierarchy to eliminate or substitute a hazard where practicable, then apply engineering and administrative controls before relying on PPE. Check each chosen control against the actual task and stop when it fails.

The best control is to design work so people do not need to be near live electricity. This may mean moving the work, isolating services, diverting lines, using reduced voltage, routing cables away from traffic or using battery tools where suitable. Administrative controls such as briefings and permits are important, but they are weaker if physical controls are missing.

PPE has a role for residual risk and specialist electrical work, but it should not be used to justify poor planning, damaged equipment or avoidable live work.

What should an electricity risk register include?

The risk register should identify specific electrical scenarios, not use electricity as a single generic entry.

A useful register separates portable tool damage, temporary supplies, overhead lines, underground cables, hidden services, charging, wet conditions, isolation and electrical contractor work. Each scenario should identify people affected, controls, evidence and stop-work triggers.

The register should be reviewed when the site layout, work sequence, plant, weather, workforce, services information or temporary supply arrangement changes.

Example electricity risk register entries - Example electricity risk register entries
Scenario Controls Evidence
Temporary cable crosses vehicle route. Reroute/protect cable and inspect daily. Site inspection record.
MEWP works near overhead line. Exclusion zone, barriers and utility consultation. Lift plan and briefing.
Excavation near buried service. Plans, locate, mark, trial holes and safe digging. Permit to dig.
Damaged tool remains in use. Pre-use check and quarantine. Defect log.
Wet outdoor work with mains tool. Suitable equipment, RCD/reduced voltage and weather review. RAMS and supervisor check.
Electrical contractor modifies live system. Dead work, isolation, proof dead and permit. Isolation certificate.

What training and competence are needed?

Training should match role and risk, from basic electrical awareness to authorised electrical work.

Most workers need practical awareness: do not use damaged equipment, keep leads away from water and traffic, report defects, respect barriers and know what to do in an emergency. Supervisors need to understand temporary supplies, RCD checks, overhead-line controls, buried-service permits and stop-work triggers.

Electrical work itself needs competent electrical people with the right qualifications, experience, tools, test equipment and authorisation. Construction managers need enough knowledge to ask the right questions and verify evidence.

RoleLearningDemonstrationAssessorRecordReassess when
People near site suppliesRecognise cables, overhead lines and damaged equipment; keep clear and summon helpPoint out a safe stand-off and report route on a site walkSite supervisorObserved inductionNew site or missed hazard
Tool and plant usersCheck leads and tools; follow marked routes and stop conditionsInspect a real tool and identify an overhead-line exclusionTask supervisorObserved pre-use and route checkNew tool, route or defect
Electrical workersIdentify all supplies, isolate, lock off and prove deadDemonstrate isolation and test at the actual work pointCompetent electrical leadAuthorisation and observed assessmentChanged circuit, failed test or incident
Site supervisors and permit issuersCoordinate excavation, lifting and temporary-supply interfacesResolve a drawing/locator conflict and hold the taskSite manager with electrical leadPermit and field observationChanged layout or plan
Designers and managersDesign out contact; resource service information and protected suppliesTrace crane and trench routes to verified controlsCompetent design or technical leadDesign review and closed actionsNew phase or repeated defect
Safety advisers and auditorsSample isolation, GS6 and HSG47 decisions against site conditionsTrace a defect to corrective action and field verificationIndependent competent reviewerAudit and action recordIncident or recurring gap

Course attendance is only one input. Observe performance on the actual task, record the scope of authorisation and reassess after change, defect or incident. First aid and electrical repair require different competence.

How does electricity support NEBOSH Construction study?

Electricity supports CN1 Element 10 by bringing together hazards, controls, overhead lines and underground cables.

For NEBOSH Health and Safety Management for Construction (UK), electricity is a major applied topic. Candidates should understand electrical hazards and risks, control measures, working near overhead power lines and working near underground cables. Strong scenario answers explain how the site is planned and controlled, not just that people should be trained.

A good answer might start with the activity: excavating for foundations, setting up temporary supplies, operating a crane near lines, using portable tools in wet conditions or refurbishing an occupied building. Then identify harm routes, who is exposed, controls, evidence and review triggers.

How can management arrangements support this topic?

HSE’s Plan–Do–Check–Act guidance helps assign ownership, deliver controls, check evidence and improve weak arrangements. Apply the relevant legal duties and task-specific technical evidence separately.

Official management guidance: HSE Managing for health and safety (HSG65)

HSE’s Plan–Do–Check–Act guidance helps assign ownership, deliver controls, check evidence and improve weak arrangements. Apply the relevant legal duties and task-specific technical evidence separately.

What are the warning signs that electricity is not managed well?

Warning signs include damaged leads, wet equipment, vague service information, poor temporary supplies and repeated defects.

Electrical weak signals should be acted on quickly. A damaged lead, overheated charger or repeated RCD trip is not minor admin; it may be the warning before a shock, fire or service strike. Site teams should treat repeated findings as system failures, not one-off worker behaviour.

A strong supervisor asks why the defect exists. Is the cable route poor? Is procurement buying weak equipment? Is programme pressure causing shortcuts? Are inspections finding defects without removing the root cause?

Warning signs and actions - Warning signs and actions
Warning sign Risk Action
Taped cable repair Shock or fire. Remove and replace.
Cables in water or traffic routes Damage and shock. Reroute/protect.
No service drawings before digging Cable strike. Stop and obtain/verify information.
Plant near overhead lines without controls Electrocution. Set exclusion zone and supervise.
Repeated RCD trips Fault or overload. Investigate, do not just reset.
Missing inspection evidence Controls may have degraded. Inspect and review schedule.

What do the acronyms and key terms mean?

Electrical and construction terms should be explained so non-specialists can follow the controls.

Acronyms and terms - Acronyms and terms
TermFull expansionMeaning here
AIS8 Agriculture Information Sheet 8 HSE agriculture information sheet on overhead electricity lines.
CAT Cable avoidance tool Cable Avoidance Tool.
CDM Construction (Design and Management) Construction (Design and Management) Regulations.
EAWR Electricity at Work Regulations Electricity at Work Regulations.
EICR Electrical Installation Condition Report Electrical Installation Condition Report.
GS6 Guidance Series 6 HSE guidance on overhead power lines.
HSG47 Health and Safety Guidance 47 HSE guidance on underground services.
PAT Portable appliance testing Portable Appliance Testing.
PPE Personal protective equipment Personal Protective Equipment.
RCD Residual current device Residual Current Device.
RAMS Risk assessments and method statements Risk Assessment and Method Statement.

Practise the checks in 3D

Follow the highlighted check, compare a sound part with a fault, and see how a missed fault can cause harm. Then use the matching blank checksheet to record what you actually find.

Browse all 25 checksheets and 26 demonstrators

Documents to download

Download editable resources from the SHAREhub environment to support your work. Working forms and spreadsheet input areas are blank. Reports, plans, guides, briefings, procedures and policies contain completed fictional example content to adapt.

Return to SHARE home