SHARE Knowledge Hub
Hazard group - fire and explosion hazards
Fire and explosion hazards arise when fuel and an oxidising source can meet an ignition source, or when a release, reaction or pressure event creates dangerous escalation. Flammable liquids and gases, combustible dust, hot work, electrical faults and accumulated fire loads can threaten workers, visitors and neighbouring premises. A fire may cause burns, smoke exposure and loss of escape routes; an explosion may also cause blast injury, flying debris and structural damage. Assessment considers inventory, release pathways, ignition, ventilation, confinement, occupancy and the effectiveness of preventive and emergency barriers. Priorities include removing unnecessary fuel, reducing quantities, containing releases, controlling ignition and protecting escape. Premises fire safety and process or DSEAR assessment have different legal routes, which must be coordinated. SHARE groups these mechanisms to support proportionate prevention and emergency planning.
Understanding Hazard group - fire and explosion hazards
Fire and explosion hazards arise when fuel and an oxidising source can meet an ignition source, or when a release, reaction or pressure event creates dangerous escalation. Flammable liquids and gases, combustible dust, hot work, electrical faults and accumulated fire loads can threaten workers, visitors and neighbouring premises. A fire may cause burns, smoke exposure and loss of escape routes; an explosion may also cause blast injury, flying debris and structural damage. Assessment considers inventory, release pathways, ignition, ventilation, confinement, occupancy and the effectiveness of preventive and emergency barriers. Priorities include removing unnecessary fuel, reducing quantities, containing releases, controlling ignition and protecting escape. Premises fire safety and process or DSEAR assessment have different legal routes, which must be coordinated. SHARE groups these mechanisms to support proportionate prevention and emergency planning.
Why this matters at work
Fire and explosion assessment starts with what can be released, how ignition or another harmful physical effect can occur, and who may be affected. Examine substance form, temperature, confinement, connected spaces and work sequence. Vapour can reach an ignition source away from its origin; dust deposits can become a later cloud. Confinement increases some consequences but is not necessary for every harmful fireball. Include receipt, transfer, production, waste, shutdown, cleaning and repair rather than accepting a normal-operation description as the complete scenario.
Assign decisions to people with the competence, authority and resources needed to implement and verify them. Dutyholders retain overall arrangements while operational managers, technical specialists and supervisors have defined tasks. Relevant engineering or explosion-protection expertise cannot be inferred from a generic safety course. Control evidence should show what was installed, how it functions, what conditions it covers and how failure is detected. Procurement, maintenance, workplace use and change decisions need coordinated ownership rather than separate checklists that leave interfaces unresolved.
How organisations manage this in practice
For a flammable liquid store with maintenance hot work, review containers, ventilation, transfer, waste, ignition sources, nearby activities and evacuation. Include abnormal releases and contractor work. Reduce inventories and releases, segregate incompatible materials and manage ignition sources. Establish appropriate zoning and suitable equipment where required. Coordinate hot work permits, fire precautions and emergency arrangements. DSEAR assessment; substance and storage inventory; zoning rationale where applicable; ignition control checks; permit records; premises fire assessment and evacuation exercise outcomes. Follow the assessment through procurement, implementation, briefing, supervision and verification rather than stopping at a document.
Fire and explosion arrangements depend on everyone who can be affected, including temporary staff, contractors, cleaners, delivery drivers, visitors and nearby occupants. Shared premises can have several responsible persons or dutyholders who need to coordinate their plans and controls. A contractor's task assessment does not remove the host's need to understand substance, building and process interfaces. Consider assistance, language, unfamiliarity and differing work hours through consultation without stereotyping people or collecting unnecessary health details. Practical control availability must match those actually present.
Check exact equipment and task identity, current permit status, linked jobs, conditions left in place and the responsible authorisation. Record unresolved work and effects on other activities in a form incoming staff can understand. Verify workplace precautions through competent checks, rather than relying only on fields or signatures. Resource issuing authorities with adequate time and supervision. Hand-back evidence should distinguish completed work, verified suitable condition and operational acknowledgement. Review permit interactions whenever scope, timing, plant condition or other work changes.
What are fire and explosion hazards and what does their assessment cover?
Fire and explosion control addresses fuel, release, ignition, confinement and consequences. Process hazards and general premises fire safety are related but have different assessment and legal routes. Read older dust guidance and the 2013 Dangerous Substances and Explosive Atmospheres Regulations (DSEAR) ACOP with current Health and Safety Executive (HSE) guidance. A general guide is not a substance specific explosion protection design. Apply the premises fire law for the correct nation. See Dangerous substances and explosive atmospheres and The storage of flammable liquids in containers.
Start with the hazard group overview, then use the related topic links for task-specific background. A group checklist helps discovery; it does not establish that the controls at your site are effective. Read the hazard group overview.
Which hazards should the assessment consider?
Check each relevant mechanism during normal work, cleaning, maintenance, foreseeable failure and emergencies. Several entries can share a harm pathway; follow the linked explanation rather than treating each label as a separate assessment. See Dangerous substances and explosive atmospheres and The storage of flammable liquids in containers.
Hazard or exposure and practical application — part 1 of 4
Read the complete visual as text
- Flammable liquids: Read the mechanism and controls: Flammable liquids gases and leaks
- Flammable gases: Read the mechanism and controls: Flammable liquids gases and leaks
- Gas leaks: Read the mechanism and controls: Flammable liquids gases and leaks
- Combustible materials: Read the mechanism and controls: Combustibles and chemical storage
Hazard or exposure and practical application — part 2 of 4
Read the complete visual as text
- Improper storage of chemicals: Read the mechanism and controls: Combustibles and chemical storage
- Hot work: Read the mechanism and controls: Hot work sparks flames and smoking
- Sparks: Read the mechanism and controls: Hot work sparks flames and smoking
- Open flames: Read the mechanism and controls: Hot work sparks flames and smoking
Hazard or exposure and practical application — part 3 of 4
Read the complete visual as text
- Smoking in restricted areas: Read the mechanism and controls: Hot work sparks flames and smoking
- Static electricity: Read the mechanism and controls: Static and explosive atmospheres
- Explosive atmospheres: Read the mechanism and controls: Static and explosive atmospheres
Hazard or exposure and practical application — part 4 of 4
Read the complete visual as text
- Dust explosions: Read the mechanism and controls: Dust explosions
- Pressure vessel failure: Read the mechanism and controls: Pressure failures and reaction escalation
- Premises fire precautions and evacuation: Read the mechanism and controls: Warning escape and occupants
Describe when the source is created or released and how it reaches someone. Compare normal operation with receipt, setup, blockage, breakdown, disposal and contractor access. The list below is a discovery aid: an omitted mechanism may still be important, while an irrelevant item does not require a fabricated assessment. Follow the mechanism explanation and test controls against the actual circumstances before scoring risk.
| Hazard or exposure | Read the mechanism and controls |
|---|---|
| Flammable liquids | Flammable liquids gases and leaks |
| Flammable gases | Flammable liquids gases and leaks |
| Gas leaks | Flammable liquids gases and leaks |
| Combustible materials | Combustibles and chemical storage |
| Improper storage of chemicals | Combustibles and chemical storage |
| Hot work | Hot work sparks flames and smoking |
| Sparks | Hot work sparks flames and smoking |
| Open flames | Hot work sparks flames and smoking |
| Smoking in restricted areas | Hot work sparks flames and smoking |
| Static electricity | Static and explosive atmospheres |
| Explosive atmospheres | Static and explosive atmospheres |
| Dust explosions | Dust explosions |
| Pressure vessel failure | Pressure failures and reaction escalation |
| Premises fire precautions and evacuation | Warning escape and occupants |
How do release, ignition and confinement determine an explosion?
Assess the substance, form, release, ignition sources, confinement and people affected. Gas and vapour can travel beyond the release point. Deposited combustible dust may become airborne and contribute to secondary explosions. Routine quantities do not alone establish the credible consequence. Process DSEAR and premises fire assessment overlap but answer different questions. Read older ACOP and dust guidance with current HSE routes. See Dangerous substances and explosive atmospheres and Safe handling of combustible dusts: Precautions against explosions.
Consider how a substance is released, where it mixes with air, what can ignite it and how confinement or connected plant changes pressure and spread. Combustion is not necessary for every pressure failure, and an exposure assessment is not an explosion-design assessment. Competent review needs the substance, process, equipment and operating conditions. New material, increased throughput or opened containment can invalidate the assumed prevention and protective measures.
How do prevention, mitigation and emergency response work together?
Reduce dangerous inventories and releases before depending on ignition control or mitigation. Consider substitution, containment, ventilation, storage, maintenance and non-routine work. Competent people determine any atmosphere classification and suitable equipment. Detection, isolation, evacuation and response must work together. Extinguishers and training do not replace release prevention. Apply premises fire arrangements for the correct United Kingdom (UK) nation. See Dangerous substances and explosive atmospheres and Fire safety in the workplace.
Prevention acts before ignition or loss of control; mitigation reduces consequences if an event occurs; emergency arrangements protect people and coordinate response. These layers have different purposes. A detector or extinguisher cannot substitute for suitable containment and ignition control, and a permit cannot physically remove fuel. Define who checks each critical layer, how occupants are warned and when loss of protection restricts operation or occupancy.
How can a small flammable release create a dangerous atmosphere?
Leaks, transfers and heated liquids can create ignitable atmospheres extending into drains or adjacent areas. See Dangerous substances and explosive atmospheres and The storage of flammable liquids in containers.
A transfer hose leaks fuel, a spray process releases solvent or a gas connection fails in a partly enclosed room. Vapour or gas mixes with air and can reach ignition beyond the leak. The absence of flames or a strong smell does not prove the atmosphere is safe.
Which source controls and checks change the outcome?
Avoid the dangerous substance or choose a suitable safer process; reduce quantity and use competent contained transfer, ventilation and ignition-control design. Verify connectors, containment and protective systems under actual conditions. Operators follow the planned response and do not search for leaks with an ignition source. Stop on leakage, an alarm or loss of a critical control; respiratory protective equipment (RPE) (PPE) is not explosion prevention and re-entry requires a competent decision.
How should the controls be applied?
Reduce inventory and release; assess containment, ventilation, transfer and storage and plan abnormal response.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Verify actual substances and conditions. Smell cannot prove an atmosphere safe.
How can storage arrangements allow a fire to spread or intensify?
Packaging, wastes and incompatible chemicals can provide fuel or initiate and worsen fire. See Chemical warehousing: The storage of packaged dangerous substances and The storage of flammable liquids in containers.
Combustible packaging accumulates near an electrical fault source or incompatible chemicals share damaged storage. A fire can spread into adjacent stock and escape routes, while some substances intensify burning or react. Receipt, decanting and waste storage may create a different risk from normal shelving.
Which source controls and checks change the outcome?
Remove unnecessary stock and combustible accumulation, substitute suitable materials and design compatible storage and containment. Competent staff assess inventory, packaging and fire interfaces for the actual premises, rather than applying one universal distance. Check deliveries, waste and damaged containers and keep escape arrangements effective. Stop incompatible or uncontrolled storage and obtain a corrected plan; extinguishers and training do not compensate for a fundamentally unsuitable storage design.
How should the controls be applied?
Control quantities, compatibility, housekeeping and separation from ignition and escape routes.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Check temporary accumulation and deliveries and current material information.
How can hot work ignite material outside the immediate work area?
Heat-producing work can ignite hidden residues, nearby fuels or atmospheres from adjacent operations. See Guidance on permit-to-work systems: A guide for the petroleum, chemical and allied industries and Dangerous substances and explosive atmospheres.
Welding on a roof, grinding near a void or heating a pipe can send heat and sparks to hidden fuel. Occupants, stored material and other contractors may be outside the worker's view. A permit with signatures can still describe an unsafe job if the fuel and interfaces were never assessed.
Which source controls and checks change the outcome?
Avoid hot work through a cold method or move it to a suitable controlled area. Where necessary, competent people establish fuel removal, separation, isolation and appropriate supervision before authorisation. Verify concealed spaces and changing conditions through the assessed method, not an arbitrary distance rule. Stop for unassessed fuel, loss of protection or changed occupants. Complete the specified post-work checks and hand-back; the observation period must follow the competent assessment rather than a universal number.
How should the controls be applied?
Consider non-hot methods; otherwise coordinate competent assessment, authorisation, area preparation and monitoring and handover.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. A signed permit does not prove precautions were implemented. Check interfaces and specified post-work arrangements.
When can static electricity ignite an explosive atmosphere?
Transfer and movement can generate ignition sources. Suitable equipment and static protection are process-specific. See Dangerous substances and explosive atmospheres and The Dangerous Substances and Explosive Atmospheres Regulations 2002.
Powder movement or liquid transfer can accumulate charge; a discharge can ignite a suitable flammable atmosphere. A low-energy spark can still matter to ignition even where shock injury is unlikely. Material properties, equipment and the surrounding atmosphere are part of the specialist assessment.
Which source controls and checks change the outcome?
Eliminate the dangerous atmosphere where possible, use suitable process conditions and competently designed containment, ventilation and electrostatic controls. Bonding, earthing and equipment suitability must be selected and checked for the actual system, not improvised. Operators maintain the authorised transfer method and report damaged connections or process changes. Hold work when atmosphere or protection assumptions are unknown; ordinary PPE or an unexplained antistatic label does not establish adequate ignition control.
How should the controls be applied?
Prevent atmospheres where possible and obtain competent classification and ignition-control specifications.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Do not invent zones, bonding designs or equipment specifications; retain design rationale.
How can combustible dust produce a primary and secondary explosion?
Suspended dust can ignite; material characteristics, confinement and connected equipment influence consequences. See Safe handling of combustible dusts: Precautions against explosions and Dangerous substances and explosive atmospheres.
Fine combustible powder is dispersed during transfer or cleaning and reaches ignition inside equipment or a room. The initial event can lift settled dust and fuel a larger secondary explosion. Not every dust is combustible, and a low inhalation score does not establish its explosion behaviour.
Which source controls and checks change the outcome?
Avoid a dispersive process or select a suitable safer material form, contain releases and prevent hazardous deposits through the assessed cleaning method. Competent specialists determine dust characteristics, ignition prevention and any required protection or isolation between connected plant. Verify extraction and protection within authorised arrangements. Stop on unexpected dust release or failed critical systems; do not invent vent sizes, cleaning thresholds or explosion protection from a generic guide.
How should the controls be applied?
Control releases and deposits and obtain competent assessment of ignition prevention and required protection or isolation.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Appearance does not establish explosibility. Generic examples cannot size venting or isolation systems.
How can pressure failure or a runaway reaction escalate an incident?
Pressure failure may cause blast without combustion. Reactions or external fire can increase pressure and combine mechanisms. See Pressure systems and Chemical reaction hazards and the risk of thermal runaway.
A heated vessel exceeds its controlled conditions or an incompatible reaction accelerates while cooling is lost. Pressure may rupture containment without combustion, while a release can also cause toxic exposure or ignite. Operators may face a developing incident before a visible fire appears.
Which source controls and checks change the outcome?
Remove unnecessary reactive or pressurised steps and use competent process design, containment and protective arrangements. Verify the operating envelope, process change controls and maintenance interfaces before starting. Operators monitor relevant conditions and use the planned stop and escalation arrangements, not improvised cooling or mixing. Hold for unexplained temperature or pressure, protective-system failure or unknown material; only authorised specialists decide on recovery and return to operation.
How should the controls be applied?
Use competent process, integrity and protective-function assessment and plan isolation and response.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Keep pressure failure distinct from explosive atmosphere; do not guess relief settings.
How do warnings and escape arrangements protect different occupants?
People remote from the fire may encounter smoke, heat and blocked escape. Assistance needs differ. See Fire safety in the workplace and Fire and rescue.
An alarm is not heard in a noisy work area, a temporary layout blocks an exit or visitors do not understand the route. Smoke, heat and delayed recognition can impair escape before staff see flames. Mobility, sensory or language needs and night staffing can change the arrangements.
Which source controls and checks change the outcome?
Prevent the initiating event and design suitable detection, warning, escape and compartmentation for the actual premises and jurisdiction. Managers coordinate temporary works, occupancy changes and support arrangements without relying on unplanned staff lifting or rescue. Check routes, doors and warnings through competent maintenance and exercises. Stop occupancy or work where critical escape protection is lost and obtain a competent remedy; firefighting by untrained staff is not the default response.
How should the controls be applied?
Coordinate warning, routes, assistance, equipment and training through the correct premises fire assessment.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Verify actual occupancy and alterations, not only a generic exercise.
How should this hazard group be assessed and managed in practice?
For a flammable liquid store with maintenance hot work, review containers, ventilation, transfer, waste, ignition sources, nearby activities and evacuation. Include abnormal releases and contractor work. Reduce inventories and releases, segregate incompatible materials and manage ignition sources. Establish appropriate zoning and suitable equipment where required. Coordinate hot work permits, fire precautions and emergency arrangements. DSEAR assessment; substance and storage inventory; zoning rationale where applicable; ignition control checks; permit records; premises fire assessment and evacuation exercise outcomes. Follow the assessment through procurement, implementation, briefing, supervision and verification rather than stopping at a document. See Dangerous substances and explosive atmospheres and The storage of flammable liquids in containers.
Agree the activity, affected people and prerequisites with operations, workers and any contractor before work. Test whether the task can be removed or redesigned, then verify selected controls in the place they will operate. During work, the supervisor compares conditions with the assessed method and has authority to stop. Completion includes safe waste or equipment handling, outstanding defects and a named hand-back decision; a completed risk form is not the end of the control process.
What must be established before assigning a risk score?
Identify the actual activity, foreseeable harm, people exposed and controls already demonstrated to work. Consider start up, normal operation, cleaning, maintenance, breakdown, emergency response and simultaneous work. A numerical matrix may support prioritisation but cannot establish compliance or replace a specialist assessment. Do not assign a residual risk score merely because a proposed control has been written into a form. Keep unknowns explicit and obtain site evidence before deciding that work can proceed. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Write a short causal description: the work creates or releases something, a person is exposed by a particular route, and a specified injury or ill-health outcome is foreseeable. Establish whether existing measures work in the actual task before estimating likelihood. An unknown material, unverified safe state or absent critical control is a decision gap, not a reason to select a reassuring number. The responsible manager records what must be resolved and who can authorise the next step.
Who owns each control and how should it be verified?
The dutyholder provides resources and arrangements. The operational manager assigns each control to someone able to implement it. Supervisors verify the controls at the point of work and respond to defects. Workers and representatives explain work as done and report problems. Specialist advisers address limits of local competence. Record the control, responsible role, evidence, check method, due date and escalation route. Completion of a training course or signature alone does not demonstrate effective risk control. See Managing for health and safety (HSG65).
Separate the person who funds and owns the control from the person who performs its check. For an engineered measure, record the accepted performance or condition, who verifies it, what a failed result means and how maintenance is coordinated. For a staffing or organisational measure, check actual cover, authority and staff experience. A signature confirms a recorded action, not effectiveness. The supervisor must be able to hold work and obtain a competent remedy when the required condition is not met.
Who might be affected, including people outside the work team?
Include employees, agency workers, apprentices, contractors, cleaners, maintainers, delivery drivers, service users, visitors and nearby public. Consider inexperience, pregnancy, disability, health conditions, language needs and lone work individually and without stereotyping. Consultation should identify barriers to controls rather than collect unnecessary medical details. Share relevant interface information between employers. A single activity may require several hazard groups; avoid splitting the assessment so that interacting controls have no clear owner. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Walk through the job from the perspective of someone who has not received the operator briefing: a cleaner, visiting driver, contractor, new starter or occupant of an adjoining area. Ask whether a control protects them during arrival, normal work, waste removal and emergencies. Agree who controls each shared boundary and how changes are communicated. Individual needs influence a suitable arrangement but do not justify treating an employee, disability or health condition as the hazard.
When should the assessment be reviewed and what evidence matters?
Reassess when equipment, materials, staffing, layout, working hours or environmental conditions change; after incidents, near misses, complaints, symptoms or evidence of failed controls; and through planned risk based review. Verify improvements under realistic demand, not only during an announced inspection. Retain dated observations, measurements where relevant, maintenance records and action closure evidence. No single review interval suits every risk. Health surveillance, exposure monitoring and clinical diagnosis are different activities and require their own competent arrangements. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Use a change or failure to test the original assumptions, not merely change the date on the form. A different product, higher throughput, altered route, new shift or contractor may change the harm pathway. Keep observations, applicable measurements, defects and authorisation evidence linked to the task. After correction, verify under representative demand and with affected workers. Repeated workarounds or symptoms require investigation of the design and organisation, even when no injury has been recorded.
How could fire and explosion hazards arise in construction and civil engineering?
In construction and civil engineering, refurbishment hot work adjoins occupied space. Coordinate alternatives permits and fire arrangements. Area and handover checks. This is an illustrative application, not a documented case or a complete method statement. See Guidance on permit-to-work systems: A guide for the petroleum, chemical and allied industries and HSE: Fire safety in construction (HSG168).
Heat or sparks can reach concealed combustibles and develop into fire after the contractor leaves, exposing occupants to smoke and blocked escape.
The premises owner and contractor first test a non-hot method, inspect both sides and hidden interfaces through competent arrangements, and agree post-work checks. Unassessed fuel or lost escape protection stops work; document hand-back before reopening.
How could fire and explosion hazards arise in manufacturing and engineering?
In manufacturing and engineering, manufacturing transfers solvents. Reduce release and assess ignition. DSEAR control evidence. This is an illustrative application, not a documented case or a complete method statement. See Dangerous substances and explosive atmospheres.
A solvent release can create a flammable mixture that meets an ignition source during transfer.
The process owner checks containment, ventilation and the assessed ignition controls before starting. A leak, failed capture or changed formulation stops transfer; a competent person verifies restoration and residual exposure before restart.
How could fire and explosion hazards arise in warehousing and logistics?
In warehousing and logistics, distribution stores flammable products. Assess compatibility and escape interfaces. Inventory and storage checks. This is an illustrative application, not a documented case or a complete method statement. See The storage of flammable liquids in containers.
Leaking or incompatible flammable stock can fuel fire and compromise escape for pickers and drivers.
The warehouse manager checks the actual inventory, separation and usable routes, not just shelf labels. Damaged containment or an unassessed storage change restricts the affected area pending competent correction.
How could fire and explosion hazards arise in agriculture and forestry?
In agriculture and forestry, farms handle grain dust. Control release and seek explosion assessment. Dust data and plant design. This is an illustrative application, not a documented case or a complete method statement. See Safe handling of combustible dusts: Precautions against explosions.
Dispersed grain dust can form an explosive cloud; deposits may contribute to a larger event.
The plant owner obtains material- and process-specific explosion assessment and verifies dust capture, cleaning and ignition prevention. Loss of extraction or unexplained overheating is a stop and investigation trigger, not an invitation to improvise cleaning.
How could fire and explosion hazards arise in hospitality and food production?
In hospitality and food production, food mills handle flour. Assess deposits release and ignition. Housekeeping and engineering checks. This is an illustrative application, not a documented case or a complete method statement. See Safe handling of combustible dusts: Precautions against explosions.
Flour released into the air can ignite, while deposits can support a further dust explosion.
The competent plant assessor evaluates the actual flour, handling and ignition sources. Supervisors verify capture and safe cleaning; unassessed deposits, failed capture or a hot defect stops affected operation until corrected.
How could fire and explosion hazards arise in retail and public services?
In retail and public services, retail accumulates packaging. Manage fuel and keep escape clear. Waste and route checks. This is an illustrative application, not a documented case or a complete method statement. See Fire safety in the workplace.
Packaging beside a heat source or exit can accelerate fire and obstruct customer escape.
The store manager removes avoidable fuel accumulation and maintains usable escape and warning arrangements. A blocked critical route is acted on immediately; closure or restriction follows the competent premises response, not a promise to clear it later.
How could fire and explosion hazards arise in offices and professional services?
In offices and professional services, offices require hot maintenance. Coordinate work with occupants. Permit and handover. This is an illustrative application, not a documented case or a complete method statement. See Guidance on permit-to-work systems: A guide for the petroleum, chemical and allied industries and HSE: Fire safety in construction (HSG168).
Hot maintenance can ignite concealed material while office occupants remain unaware of the developing fire.
Facilities and the contractor assess alternatives, occupied interfaces and the nation-specific premises arrangements. Changed occupancy or an unknown concealed space is a hold point; retain authorisation, post-work checks and explicit hand-back.
How could fire and explosion hazards arise in education and laboratories?
In education and laboratories, laboratories transfer solvents. Assess actual handling and compatibility. Inventory and task assessment. This is an illustrative application, not a documented case or a complete method statement. See The storage of flammable liquids in containers.
A solvent spill near heating or an incompatible material can initiate fire or an energetic reaction.
The laboratory manager verifies quantities, compatibility, containment and authorised methods. Stop for unidentified chemicals, failed capture or a scale change outside the assessment; trained competent people decide safe recovery.
How could fire and explosion hazards arise in utilities and waste management?
In utilities and waste management, waste plants receive variable combustibles. Assess feedstock ignition and releases. Feedstock and response controls. This is an illustrative application, not a documented case or a complete method statement. See Dangerous substances and explosive atmospheres.
Variable incoming waste may include ignition sources or combustible material not covered by the process assessment.
The operations manager checks feedstock acceptance, containment and response capability. Unidentified hot or reactive loads are isolated through the assessed trained response; do not process them merely because the queue is growing.
How could fire and explosion hazards arise in energy and process industries?
In energy and process industries, process plants change reaction conditions. Use competent change assessment. Reaction and pressure evidence. This is an illustrative application, not a documented case or a complete method statement. See Chemical reaction hazards and the risk of thermal runaway and Pressure systems.
A changed reaction can generate heat and pressure faster than the plant can safely manage, with fire, rupture or explosion consequences.
The process owner requires competent change assessment and verified protective design before introduction. Unexpected temperature, pressure or loss of critical protection triggers the established plant response; general guidance cannot set universal alarm values.
How could fire and explosion hazards arise in events and transport operations?
In events and transport operations, events combine fuels power and crowds. Coordinate storage ignition and escape. Integrated assessment. This is an illustrative application, not a documented case or a complete method statement. See Dangerous substances and explosive atmospheres and Fire safety in the workplace.
A fuel leak, temporary power fault or crowd-blocked exit can turn a local fire into a wider public emergency.
The organiser coordinates suppliers, storage, ignition control, warning and escape for the actual venue. Loss of required separation or safe exit capacity pauses the activity; reopening needs competent checks rather than a changed warning sign.
How do you put the controls into practice?
Move from recognising harm to deciding, implementing, checking and improving the controls. Give each critical control an owner, a check method and a clear escalation route. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
- Understand the taskObserve people, equipment, materials and interfaces.
- Describe the harmIdentify exposure, energy release and foreseeable failure.
- Control at sourceAvoid, redesign, substitute, contain or separate the hazard.
- Check in real workVerify performance, defects, ownership and change triggers.
| Stage | Action | Who acts | Evidence to retain |
|---|---|---|---|
| Before work | Confirm the actual task, people, equipment, substances, location and abnormal conditions. | Operational manager with competent advice | Assessment, observations, consultation and required specialist checks |
| Control delivery | Reduce inventories and releases, segregate incompatible materials and manage ignition sources. Establish appropriate zoning and suitable equipment where required. Coordinate hot work permits, fire precautions and emergency arrangements. | Responsible manager and authorised implementers | DSEAR assessment; substance and storage inventory; zoning rationale where applicable; ignition control checks; permit records; premises fire assessment and evacuation exercise outcomes. |
| During work | Supervise the real activity; check that critical controls remain effective and workers can report problems. | Supervisor and workers | Checks, defects, changes and escalations |
| Stop and restart | Stop the affected activity when serious danger or a failed critical control is suspected. Restart only through the competent site authorisation arrangements. | Supervisor and authorised competent person | Reason for stopping, corrective action, verification and restart authority |
| Review | Revisit controls after change, incidents, near misses, symptoms or repeated defects. Check effectiveness rather than counting completed forms. | Manager, Occupational safety and health (OSH) adviser and worker representatives | Dated review, closure evidence and lessons for design and procurement |
How does ERICPD apply to fire and explosion hazards?
ERICPD stands for Eliminate, Reduce, Isolate, Control, PPE and Discipline. For fire and explosion hazards, start by removing the hazardous task or source where practicable, then reduce and separate the remaining exposure. Combine suitable safeguards and work arrangements, use relevant personal protective equipment for residual risks, and keep all selected measures effective in everyday work. See HSE: Managing risk using PPE and Managing for health and safety (HSG65).
- 1 · E Eliminate
Remove the hazardous task or source where practicable; confirm that the alternative still fulfils the task and assess remaining hazards.
- 2 · R Reduce
Use a suitable less hazardous material, process or equipment, or reduce the hazard at source. Check any new risks introduced.
- 3 · I Isolate
Separate people from the hazard through suitable containment, guarding, barriers or other task-specific separation.
- 4 · C Control
Put remaining safeguards and workable task arrangements in place. Engineering controls and administrative arrangements have different strengths.
- 5 · P PPE
Select personal protective equipment for relevant residual exposure. Check suitability, fit, compatibility, use and maintenance.
- 6 · D Discipline
Sustain the controls through management support, supervision, maintenance and learning. Resolve workarounds and failures without blaming workers.
Eliminate, Reduce and Isolate focus attention on the hazard and the exposure pathway before reliance on behaviour or PPE. Controls usually work together: an enclosure may still need safe access, maintenance and instruction. Record the reasons for choosing or rejecting stronger options and check the complete task, including cleaning, maintenance and foreseeable changes.
ERICPD is a practical learning mnemonic. The five-level hierarchy is elimination, substitution, engineering controls, administrative controls and PPE. Reduce may include substitution or source reduction; Isolate commonly involves engineering. Control can include engineering and administrative measures. Discipline supports every selected level and is not an additional protective barrier. These frameworks are related; their labels do not form identical statutory ladders.
What does each role need to know and demonstrate?
People need learning and demonstrated competence for the decisions they actually make, not the same course at every organisational level. See Dangerous substances and explosive atmospheres and The storage of flammable liquids in containers.
For fire and explosion hazards, frontline learning must enable staff to recognise releases, ignition interfaces and escape failures. Supervisors need to verify hot-work prerequisites and changing fuel or occupancy. Design, procurement and specialist assessment require deeper competence in substance-specific prevention, storage and premises fire arrangements. Awareness, supervised practice, assessment and authorisation are different stages; an attendance record alone does not establish competence or permit specialist intervention.
Assess practical understanding with the actual task and credible abnormal conditions. The assessor must be competent for the scope being tested; authorisation should state its boundaries. Reassess after a material change, a defect, a demonstrated gap or work outside that scope rather than assuming one fixed refresher interval suits every role.
| Role | Learning and decisions | Assessment, evidence and reassessment |
|---|---|---|
| Nearby staff and new starters | Recognise the relevant exposure, usable routes, warning signs and reporting or emergency arrangements. | Supervisor checks a practical explanation and scenario response; retain briefing scope and gaps. Repeat when routes or conditions change. |
| Frontline users | Demonstrate how to recognise releases, ignition interfaces and escape failures, including the checks, limits and stop decision. | Competent task assessor observes representative practice and a defect scenario; record task, equipment/material scope and authorisation. Reassess for changed methods or performance gaps. |
| Specialist workers and maintainers | Demonstrate the applicable technical method, safe state, interface controls and hand-back; do not infer specialist skill from general awareness. | Competent specialist assesses work within a defined scope; retain method, assessment and authorisation evidence. New equipment, material or fault type may need a new decision. |
| Supervisors and coordinators | Demonstrate how to verify hot-work prerequisites and changing fuel or occupancy, manage a changed condition and hold or release work. | Manager or competent reviewer tests a realistic planning and stop/restart scenario; retain observed decisions and corrective actions. Review following interface failures. |
| Managers, purchasers and designers | Make and resource decisions on substance-specific prevention, storage and premises fire arrangements, including the stronger-control options and residual risks. | Competent review of specifications, trials, procurement acceptance and effectiveness evidence; record decision owner and outstanding actions. Reassess after process or organisational change. |
| OSH advisers, technical specialists and auditors | Distinguish jurisdiction and source limits, test representative evidence and recognise the boundary of their competence. | Appropriately competent review of the actual assessment, sources, sampling and closed actions; retain scope and limitations. Escalate missing technical information rather than inventing a conclusion. |
How can the hierarchy of controls reduce workplace fire and explosion risks?
A workshop transfers flammable cleaning liquid beside processes that may create ignition sources. A release can form a flammable atmosphere and a fire or explosion may affect workers and other occupants. Health exposure and fire risks both need assessment.
Illustrative SHARE example: assess stronger options first, then combine the measures needed for the remaining task. If elimination removes the task entirely, later measures address only remaining or different hazards. Each stage below explains what changes, how harm is reduced and who verifies it.
Applying ERICPD to other hazards in this group
For hot work, combustible dust and reactive processes, remove unnecessary ignition or hazardous operations first, then assess containment, source capture, ignition prevention and consequences. Emergency arrangements are a further layer; they do not make an uncontrolled atmosphere safe.
Keep an assessment record of the chosen controls, reasons for the selection, action owner, verification evidence and failure response. A failed critical control requires the affected activity to be held and corrected through the competent site arrangements; PPE or a completed form does not override that decision.
Guidance supporting these teaching examples
- HSE: Managing risk using PPE
- Managing for health and safety (HSG65)
- Dangerous substances and explosive atmospheres
- Chemical reaction hazards and the risk of thermal runaway
- Chemical warehousing: The storage of packaged dangerous substances
- Guidance on permit-to-work systems: A guide for the petroleum, chemical and allied industries
- Fire safety in the workplace
- Fire and rescue
- The Fire Safety Regulations (Northern Ireland) 2010
How would a powder-handling change affect fire and explosion controls?
Manage this activity by preventing exposure at source, coordinating the affected people and verifying the planned controls before release. A food or manufacturing process introduces a different powder and increases transfer rate. Operators, cleaners and maintenance staff can encounter inhalation exposure and, if the material is combustible, an ignition and explosion pathway. Dust collecting outside the process can fuel escalation. See Safe handling of combustible dusts: Precautions against explosions and Dangerous substances and explosive atmospheres.
Illustrative SHARE workplace example
What must be agreed before work starts?
The process manager holds the change until competent people assess the actual material properties, process release, ignition and connected plant. Consider avoiding the powder form or using a suitable less dispersive method, then verify containment and protective design. Commissioning and maintenance requirements must fit the new conditions. Do not derive explosion behaviour or protection settings from a Control of Substances Hazardous to Health (COSHH) rating.
What changes, stops or hand-back decisions matter?
Supervisors check release, deposits and the authorised cleaning method during operation. A failed critical extraction or protective system, unexpected dust or unassessed maintenance is a stop point. Competent staff determine safe recovery and release, documenting material identity, design assumptions, checks and hand-back. Respiratory protection addresses remaining exposure where selected; it does not prevent ignition or protect the whole plant from an explosion.
How should jurisdiction, local rules and management assurance be handled?
Apply the law and regulator guidance for the work location, then use competent task and equipment information to establish the practical arrangements. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
HSE guidance generally addresses Great Britain; Northern Ireland has its own instruments and Health and Safety Executive for Northern Ireland (HSENI) route. Construction, dangerous substances, equipment and other specialist topics need the applicable instrument, not a Great Britain (GB) duty copied into a Northern Ireland (NI) answer. Fire arrangements also differ across the UK nations. Foreign project examples require destination-specific official advice and competent local assessment.
Distinguish a legal duty, regulator guidance, an organisation's rule and an illustrative SHARE method. A management system can link assessment, procurement, competence, maintenance, consultation and corrective action; a certification label or an unverified standard clause does not authorise work. For this group, sample evidence on substance-specific prevention, storage and premises fire arrangements and compare the recorded method with the activity observed on site. Resolve conflicts or missing technical information with the responsible competent person.
How would planning hot work during premises maintenance work in practice?
Contractors propose hot work near stored combustible material while the premises remain occupied. Sparks or heat can reach fuel beyond the immediate work area, while a released flammable substance can introduce an explosion risk. The manager first considers a non-hot method or completing the work in a safer, separately controlled location. See Dangerous substances and explosive atmospheres and Guidance on permit-to-work systems: A guide for the petroleum, chemical and allied industries.
Illustrative SHARE workplace example
What is required before and during the activity?
Before authorisation, competent people assess fuel, ignition, concealed spaces, interfaces and escape arrangements. Any permit supports those controls; it does not physically remove fuel or make a flammable atmosphere safe. During work, maintain the agreed separation, monitoring and supervision. Stop if unassessed materials appear, conditions change or a critical fire or explosion control is lost.
What does safe completion and hand-back require?
Complete the agreed post-work checks and hand-back, including any observation period determined by the competent assessment; do not invent a universal duration. Keep authorisation, checks, defects and close-out evidence. A process plant needs substance- and plant-specific explosion assessment, while occupied premises also require their nation-specific fire arrangements.
Acronyms and terms
These terms distinguish the source of harm, the exposure route and the controls needed for the actual work.
| Letters or term | Expansion or definition | Meaning in this topic |
|---|---|---|
| UK | United Kingdom | A geographical description, not one identical set of health-and-safety instruments. |
| GB | Great Britain | England, Scotland and Wales; HSE guidance is generally framed for this jurisdiction. |
| NI | Northern Ireland | A separate health-and-safety legal route overseen by HSENI. |
| HSE | Health and Safety Executive | The GB regulator and a publisher of official workplace guidance. |
| HSENI | Health and Safety Executive for Northern Ireland | The NI regulator; check its applicable requirements and advice. |
| OSH | Occupational safety and health | Preventing work-related injury and ill health. |
| PPE | Personal protective equipment | Equipment worn for remaining exposure; it does not replace stronger source controls. |
| COSHH | Control of Substances Hazardous to Health | The GB hazardous-substance assessment and exposure-control route. |
| DSEAR | Dangerous Substances and Explosive Atmospheres Regulations | The GB route for relevant dangerous-substance fire, explosion and other safety risks. |
| ERICPD | Eliminate, Reduce, Isolate, Control, PPE, Discipline | A learning mnemonic for selecting and sustaining controls; not a statutory ladder. |
| Hazard | A source or condition with potential for harm | Describe what creates harm, rather than calling a person the hazard. |
| Exposure | A route or contact connecting source and person | Consider dose, duration and circumstances where relevant. |
| Critical control | A measure essential to the safe arrangement | Define its required condition, check, owner and failure response. |
| Hand-back | Controlled return to operation or use | Confirm people, equipment, protection and outstanding conditions before release. |
Example handy documents
Useful records connect the actual task to control ownership, checks, stop decisions and verified hand-back. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
The following are examples of documents an organisation could create or adapt, not downloadable files or a complete safe system. Use the task-specific information and competent review before applying them. Keep private health information outside general operational records.
What should a task and harm-route assessment contain?
Record people, source, exposure or energy, foreseeable harm, existing controls, stronger options, residual uncertainty and the responsible decision owner.
What should a critical-control check and defect log contain?
Record the required condition, check method, responsible person, failed result, restricted work and verified corrective action.
What should a change and hand-back record contain?
Capture changed material, equipment, staffing, layout or conditions; prerequisites, hold decisions, competent verification and restart authority.
What should a competence and authorisation record contain?
Name the assessed task and scope, practical evidence, assessor, limits, supervision and reassessment triggers.
What should an operational learning review contain?
Link observations, complaints, near misses or relevant exposure evidence to a design or organisational change and an effectiveness check.