SHARE Knowledge Hub

Risk Management

Risk management connects hazard discovery, proportionate assessment, higher-order controls, accountable implementation, assurance and learning across the organisation. A form or risk matrix is a decision aid, not evidence that exposure fell. Leaders must prioritise serious and uncertain harm, resource controls, verify performance and revisit decisions after change or failure.

Updated 2026-10-19GB and NIVersion 2.2

Understanding Risk Management

Risk management connects hazard discovery, proportionate assessment, higher-order controls, accountable implementation, assurance and learning across the organisation. A form or risk matrix is a decision aid, not evidence that exposure fell. Leaders must prioritise serious and uncertain harm, resource controls, verify performance and revisit decisions after change or failure.

Why this matters at work

For operational use, write cause-event-consequence statements, identify affected objectives and distinguish uncertainty from the harm, hazard or control itself. Involve workers, specialists, delivery partners and people affected by the decision because risk information is distributed across the system.

Keep current exposure and verified controls separate from hoped-for future improvements. State uncertainties, action dates, interim measures and escalation conditions. Use the register in planning, procurement, staffing and change decisions, and check whether actions work in the field. For a serious scenario, link supporting technical assessments rather than compressing the entire decision into a colour. Review after material change or control failure and give leaders evidence they can challenge. Approval should identify who decided what, on which basis and for how long, rather than merely confirm that the register was read.

How organisations manage this in practice

Define conditions for readiness, training and supervised familiarisation, retaining suitable cover until those conditions are met. Record assumptions, risk and control owners, action resources and review triggers. Trial proportionately where appropriate and monitor real workload and barrier performance after change. Stop or revise the transition if critical functions are unsupported. Do not use a low historical injury rate as proof that fewer competent people will be sufficient. If technical modifications accompany the reorganisation, control those separately through the relevant engineering and configuration review.

Reopen a decision when its basis may no longer hold: new material or equipment, software changes, altered staffing or workload, a changed location, an incident, a failed control, new health evidence or updated law or guidance. Include temporary arrangements and transitions, which often have different risks from normal operation. Check both the technical configuration and the organisation expected to sustain it. A routine review date does not justify waiting when a material assumption has already failed. Preserve the previous decision and evidence trail, record what changed and assess affected controls and interfaces. Allocate actions, interim restrictions and reauthorisation requirements before returning to the new condition. Update procedures, drawings, training, emergency arrangements and risk records as appropriate, then verify implementation. Confirm source edition, status and territorial applicability for consequential claims. Treat a review as a new evidence-based decision, not a fresh signature on unchanged text. Where uncertainty remains material, state the next evidence step and keep the necessary protection in place.

Distinguish the person accountable for the risk outcome from those operating or maintaining controls and those delivering improvements. Give each a defined scope, authority, resources and deputies. Map interfaces where no department can control the whole pathway alone, such as operations relying on contractor maintenance and facilities providing a critical utility. Contracting out an activity does not make the undertaking's coordination and assurance needs disappear. Identify whose approval is needed when a control is unavailable or work changes. Record dependencies and escalation thresholds in practical arrangements, not only a corporate chart. Confirm that each owner accepts the role and can obtain reliable evidence. Test what happens on nights, absence or organisational change and update responsibility before gaps arise. Use joint reviews and direct checks where control crosses boundaries. A risk register should point to the actual operating and handover records. If an owner lacks authority or resources, escalate that governance defect rather than leaving them named on an action they cannot deliver.

A decision must reach the workface

Risk management connects assessment, resources, implementation, assurance and learning. An email or a purchased sign does not change a wet floor.

Safety inspection of a clear route through a UK workplace. Photorealistic illustration.
Illustrative UK workplace scene. Read the practical checks below for responsibilities, evidence and limits. Download image · Download smaller image
  1. Assess the actual source

    For the changing-room case, locate wet sources, transitions, cleaning and real busy-use conditions.

  2. Resource a feasible change

    The facilities and operating owners arrange an assessed surface, drainage or source-control improvement with necessary interim protection.

  3. Implement and check

    Verify the actual workface change during representative use and with worker feedback; a drawn drain does not establish slip resistance.

  4. Learn across sites

    Return the result to priorities and similar tasks. Keep the separate transport hierarchy case clearly identified; it is not a control for the wet-floor example.

Read the complete task-specific control examples

ERICPD is a planning cross-map: Discipline verifies and sustains every control. ESEAP compares effectiveness. A label does not authorise the task; retain the owner, evidence and stop or change decision.

Risk Management · ERICPD

Eliminate
Move deliveries to an existing external bay so vehicles never cross the pedestrian route, if swept path and access checks show no new public conflict.
Reduce
Where removal is infeasible, substitute a forward-entry, forward-exit delivery pattern for reversing.
Isolate
Specify fixed impact-rated barriers and a gated pedestrian crossing outside the turning radius; paint or a sign alone is not physical isolation.
Control
Fit and test speed limiting, reversing alarms and sight-line aids as residual safeguards; set a documented traffic plan with a named marshal only where required.
PPE
Use suitable high-visibility clothing for remaining visibility risk; it offers no impact protection against a vehicle and cannot justify a shared path.
Discipline
Brief route changes, supervise actual crossing behaviour, inspect barriers and review near misses and traffic counts; repair design failures at source rather than blaming users.

Risk Management · ESEAP

Elimination
Move deliveries to an existing external bay so vehicles never cross the pedestrian route, if swept path and access checks show no new public conflict. HSE workplace-transport guidance
Substitution
Where removal is infeasible, substitute a forward-entry, forward-exit delivery pattern for reversing. Reducing booking overlap alone only lowers exposure and remains administrative. HSE workplace-transport guidance
Engineering controls
Specify fixed impact-rated barriers and a gated pedestrian crossing outside the turning radius; paint or a sign alone is not physical isolation. HSE workplace-transport guidance Install and prove speed-limiting equipment, warning/sight-line aids and physical visibility improvements after segregation design; instructions do not replace their function. HSE workplace-transport guidance
Administrative controls
Maintain the traffic plan, authorised human roles, inspection, functional-test arrangements, briefings and response to defects. Suspend conflicting movement when the designed controls fail. HSE workplace-transport guidance Brief route changes, supervise actual crossing behaviour, inspect barriers and review near misses and traffic counts; repair design failures at source rather than blaming users. HSE workplace-transport guidance
PPE
Use suitable high-visibility clothing for remaining visibility risk; it offers no impact protection against a vehicle and cannot justify a shared path. HSE workplace-transport guidance

What are HSE’s five risk assessment steps?

Follow a depot team as it assesses a shared forklift crossing, changes the layout and checks the controls during deliveries.

  1. Identify hazards

    Walk through the job with the people who do it. Look at routine work, cleaning, maintenance and changes. Check near misses for ways people have already come close to harm.

    At the depot. At the depot, the team finds that forklifts and pedestrians use the same crossing during unloading.

  2. Assess the risks

    Identify who might be harmed and how. Consider workers, contractors, visitors and anyone who needs different arrangements. Judge how likely harm is and how serious it could be, taking account of controls already in use.

    At the depot. Depot staff and visiting drivers cross the route. A forklift strike could cause serious or fatal injuries. Markings and briefings still leave people and vehicles sharing the crossing.

  3. Control the risks

    First consider removing the hazard or avoiding exposure. If risk remains, choose controls that act at source and protect everyone affected. Put the measures into use and brief the people who rely on them.

    At the depot. Reroute pedestrians away from unloading where possible. Where a crossing is still needed, fit barriers and choose a crossing point with clear sightlines. Restrict access until the arrangement is ready.

  4. Record your findings

    Record the significant hazards, who may be harmed, the controls in place and any further action. Name an owner, a due date and the evidence needed to close the action. In Great Britain, employers with five or more employees must record significant findings.

    At the depot. The depot supervisor records the temporary restriction, who owns the permanent route changes, when they are due and who will check them. The shift briefing explains the change to staff and visiting drivers.

  5. Review the controls

    Check that the controls work during real shifts. Review when controls may no longer work, after changes, when workers raise problems, or after accidents and near misses. Update the assessment and brief affected people.

    At the depot. Observe a busy delivery after installation. Check that people use the crossing, sightlines stay clear and barriers are intact. If the route is blocked or bypassed, deal with that before relying on the assessment.

Fictional photographic illustrations of the same depot.

Read the five steps on the HSE website

How do you use the SHARE 5 × 5 risk matrix?

The 5 × 5 is a semi-quantitative rating method. The numbers represent judgement categories. Use the score to prioritise action and make the reasoning visible. Confirm the controls and applicable requirements before deciding whether the remaining risk is tolerable.

  1. Describe the harm scenario. Write one credible event and outcome for each hazard. Identify who is exposed, how often, and which current controls have been checked.
  2. Choose likelihood and severity. Select likelihood (L) from 1 to 5 for that outcome under current conditions. Select severity (S) from 1 to 5 for the credible harm. Record why you chose each number.
  3. Calculate and act. Multiply L by S and read the SHARE band. Record what needs doing, who owns the action and what must happen before work can proceed. Deal with a critical gap regardless of the score.
  4. Plan further controls and reassess. Estimate the proposed residual score separately. Verify the controls in use before relying on that score. Reassess likelihood and severity with reasons. A control may make harm less likely while leaving the possible severity unchanged.
SHARE risk score = likelihood × severity
Likelihood / severityS1 MinorS2 ModerateS3 SeriousS4 MajorS5 Catastrophic
L5 Almost certain5Medium10High15High20Very high25Very high
L4 Likely4Low8Medium12High16Very high20Very high
L3 Possible3Low6Medium9Medium12High15High
L2 Unlikely2Low4Low6Medium8Medium10High
L1 Rare1Low2Low3Low4Low5Medium

SHARE bands are 1–4 Low, 5–9 Medium, 10–15 High and 16–25 Very high.

Worked score

The conveyor example records 3 × 5 = 15 (High) with isolation still unverified. The proposed 1 × 5 = 5 (Medium) depends on verified isolation and other controls. Intrusive work stays on hold in the example.

Download the 5 × 5 report and matrix (PDF)

Compare both assessment formats

Download worked SHAREintelligence assessments

Compare two complete fictional teaching reports exported from the SHAREintelligence assessment tools. Each includes four hazard lines, evidence, actions, responsibilities and review arrangements.

Scored assessment · Conveyor maintenance

The conveyor example records 3 × 5 = 15 (High) with isolation still unverified. The proposed 1 × 5 = 5 (Medium) depends on verified isolation and other controls. Intrusive work stays on hold in the example.

Download scored assessment PDF

Open the 5 × 5 assessment creator

Qualitative assessment · Cleaning-product preparation

The cleaning example explains splash and skin-contact risks in words. It prioritises stopping unprotected decanting, reviewing safer methods and checking the chosen control before release.

Download qualitative assessment PDF

Open the qualitative assessment creator

Open the full SHAREintelligence procedure

What is risk management in health and safety?

Risk management is the continuing process of finding credible harm, choosing proportionate controls, assigning owners, checking whether exposure actually fell and learning after change. A risk matrix or completed assessment form is only a decision aid, not a functioning control system.

Risk management is a functioning control system

Risk management is a functioning control system. POLICY AND INTENT: Set direction and expectations. Useful output: Clear commitment, scope and accountabilities. RISK ASSESSMENT: Control tasks, hazards and affected people. Useful output: Suitable and sufficient assessments and action plans. RISK PROFILING: Prioritise the biggest organisational risks. Useful output: Top-risk profile, control confidence and assurance plan. CONTROL SELECTION: Reduce risk at source where reasonably practicable. Useful output: Hierarchy-led control decisions and ALARP evidence. IMPLEMENTATION: Turn decisions into work controls. Useful output: Procedures, permits, training, equipment and supervision. MONITORING AND ASSURANCE: Check whether controls stay effective. Useful output: Inspections, audits, critical-control checks and review. LEARNING: Improve after weak signals or change. Useful output: Incident learning, action verification and risk-register update.
Learning point: The assessment, profile, control choice, implementation and assurance form a continuing system. A matrix or completed form is a decision aid, not the control.
Read the complete visual as text
  1. POLICY AND INTENT: Set direction and expectations. Useful output: Clear commitment, scope and accountabilities.
  2. RISK ASSESSMENT: Control tasks, hazards and affected people. Useful output: Suitable and sufficient assessments and action plans.
  3. RISK PROFILING: Prioritise the biggest organisational risks. Useful output: Top-risk profile, control confidence and assurance plan.
  4. CONTROL SELECTION: Reduce risk at source where reasonably practicable. Useful output: Hierarchy-led control decisions and ALARP evidence.
  5. IMPLEMENTATION: Turn decisions into work controls. Useful output: Procedures, permits, training, equipment and supervision.
  6. MONITORING AND ASSURANCE: Check whether controls stay effective. Useful output: Inspections, audits, critical-control checks and review.
  7. LEARNING: Improve after weak signals or change. Useful output: Incident learning, action verification and risk-register update.

Risk management is sometimes reduced to a matrix, but the matrix is only a small tool. The professional task is to understand what could go wrong, who could be harmed, how severe the harm could be, how likely or credible the scenario is, what controls are in place, what further controls are reasonably practicable and how the organisation knows controls work.

A serious risk management system also asks what the organisation may be blind to: occupational disease, contractors, change, temporary work, weak maintenance, workload, vulnerable workers, major accident hazards and low-frequency high-consequence events.

ComponentPurposeGood output
Policy and intentSet direction and expectations.Clear commitment, scope and accountabilities.
Risk assessmentControl tasks, hazards and affected people.Suitable and sufficient assessments and action plans.
Risk profilingPrioritise the biggest organisational risks.Top-risk profile, control confidence and assurance plan.
Control selectionReduce risk at source where reasonably practicable.Hierarchy-led control decisions and ALARP evidence.
ImplementationTurn decisions into work controls.Procedures, permits, training, equipment and supervision.
Monitoring and assuranceCheck whether controls stay effective.Inspections, audits, critical-control checks and review.
LearningImprove after weak signals or change.Incident learning, action verification and risk-register update.

How can the hierarchy of controls guide practical workplace risk reduction?

Choose the assessment method for the decision. A generic assessment can give a starting standard for repeated comparable tasks, but the assessor must check local equipment, people and conditions. A specific assessment addresses a defined task, substance or regulated hazard and records its actual exposure and controls. A dynamic assessment supports changing conditions at the point of work; it is a live pause-and-adjust tool, not a substitute for planned assessment. A quantified assessment estimates likelihood or consequence using stated data and assumptions when the decision warrants it; do not imply numerical precision when inputs are weak. The competent assessor chooses the method, observes the work and consults workers; the action owner records the control, due date and field verification. Reassess after change, a failed control, incident or new exposure information. HSE risk steps and HSENI risk guidance support the GB and NI routes.

Risk management connects risk information to decisions, resources, controls and assurance. A dynamic assessment helps respond to changed conditions but cannot replace planned or specialist assessment; if a new chemical is unidentified, stop and get competent substance information before the job continues.

A strong risk management system starts with context: activities, people, legal duties, assets, contractors, public interface, organisational change and risk appetite. It then builds controls into planning and work execution, not as an afterthought.

The system should be visible from the boardroom to the workface. A worker should know the control that matters for the task. A supervisor should know how to verify it. A manager should know what to escalate. A director should know whether the organisation's most serious controls are healthy.

StageQuestionEvidence
ContextWhat work, people, assets and legal duties shape the risk?Scope, organisation chart, legal register and risk profile.
IdentifyWhat could cause serious harm, ill health or major loss?Hazard register, worker input, incident data and specialist assessments.
AssessWho may be harmed and how credible is the scenario?Task assessments, risk scenarios and affected-persons analysis.
ControlWhat control is most effective and reasonably practicable?Hierarchy-led action plan and ALARP rationale.
ImplementWho owns the control and how is it used?Procedures, permits, training, resources and supervision.
CheckHow do we know the control works today?Inspection, verification, monitoring and audit evidence.
ReviewWhat changed and what did we learn?Management review, updated risk register and improvement plan.

Illustrative warehouse decision: the risk register shows repeated near misses where an articulated delivery vehicle reverses across a pedestrian route. The risk owner must test source removal before accepting a lower-order rule. ERICPD (Eliminate, Reduce including substitution, Isolate, Control, Personal Protective Equipment, Discipline) is a teaching prompt; the HSE five-level hierarchy orders elimination, substitution, engineering, administrative controls and PPE. Reduce, Isolate and Discipline do not map one-to-one to those five levels. The chosen route, geometry and stopping points need local design and verification. See HSE workplace-transport guidance for the vehicle route and HSE hierarchy of controls for control order.

On a narrow screen, scroll the control table sideways for the owner and stop decision.

Control choices follow the harm path: remove or substitute the source where reasonably practicable, then isolate through engineering or redesign. Use procedures, supervision and PPE for remaining exposure rather than accepting them as the first answer to a design failure. For a repeated wet-floor slip, fix drainage or floor design before relying on warning signs and footwear; assign a facilities owner, verify the repair during busy service and stop access if the surface remains unsafe. HSE control hierarchy supports the order.

How does a risk management system change a real decision?

A worked example shows how risk management prevents a local issue becoming a repeating organisational failure.

Changing-room slips: change the conditions, then verify

Changing-room slips: change the conditions, then verify. IDENTIFY THE REPEATING PATTERN: A leisure group links repeated changing-room slips rather than filing each event in isolation. Review when and where floors become wet. ASSESS CREDIBLE HARM: Consider serious fall potential, vulnerable users, busy periods, lighting, cleaning and the people actually exposed. Minor injuries so far do not establish a tolerable future outcome. REDESIGN THE SOURCE: The facilities owner reviews drainage, floor surface and cleaning method before relying on warning signs or footwear. Use assessed access restriction while an unsafe wet surface remains. RESOURCE AND IMPLEMENT: Leaders allocate resources and a named owner; supervisors implement the standard and check contractor cleaning and inspection timing. An email reminder does not change the floor. CHECK BUSY SERVICE: Observe the repair and cleaning method under busy use. Track wet-floor findings, inspections, near misses and user feedback as well as injuries. VERIFY AND SHARE LEARNING: Check whether repeat events and the live hazard reduce; inspect similar sites and update the group standard. Buying signs does not close the design action.
Learning point: A concrete sequence joins risk identification, source control, leadership resources and effectiveness evidence. Restrict access if the surface remains unsafe and reassess the controls.
Read the complete visual as text
  1. 1. IDENTIFY THE REPEATING PATTERN: A leisure group links repeated changing-room slips rather than filing each event in isolation. Review when and where floors become wet.
  2. 2. ASSESS CREDIBLE HARM: Consider serious fall potential, vulnerable users, busy periods, lighting, cleaning and the people actually exposed. Minor injuries so far do not establish a tolerable future outcome.
  3. 3. REDESIGN THE SOURCE: The facilities owner reviews drainage, floor surface and cleaning method before relying on warning signs or footwear. Use assessed access restriction while an unsafe wet surface remains.
  4. 4. RESOURCE AND IMPLEMENT: Leaders allocate resources and a named owner; supervisors implement the standard and check contractor cleaning and inspection timing. An email reminder does not change the floor.
  5. 5. CHECK BUSY SERVICE: Observe the repair and cleaning method under busy use. Track wet-floor findings, inspections, near misses and user feedback as well as injuries.
  6. 6. VERIFY AND SHARE LEARNING: Check whether repeat events and the live hazard reduce; inspect similar sites and update the group standard. Buying signs does not close the design action.

A leisure group notices repeated slips in changing rooms. A weak response is to remind staff to mop more often. A stronger risk management response looks at flooring, drainage, cleaning method, peak occupancy, footwear, signage, lighting, inspection evidence, contractor cleaning standards, accident trends and whether the same issue exists across sites.

The risk is then controlled through design and operating standards, not just reminders. Leaders see the trend, approve resources for drainage or flooring where needed, and review whether the actions reduce repeat incidents.

Risk-management stepWeak responseStronger response
IdentifyRecord each slip separately.Recognise a repeated wet-floor risk pattern.
AssessScore as medium because injuries are minor so far.Consider serious fall potential, vulnerable users and peak exposure.
ControlTell staff to mop more.Improve drainage, surface, cleaning method, barriers and inspection timing.
ImplementEmail reminder.Named owner, standard, resources and supervisor checks.
MonitorCount accidents only.Track inspections, wet-floor findings, near misses and user complaints.
ReviewClose actions once signage bought.Verify whether repeat events reduce and update group standard.

A guard defect needs capital expenditure

Task, material and setting: An operator reports a recurring guard bypass that speeds production.

People and prerequisites: Supervisor stops unsafe operation and records the credible hand-injury scenario; engineering and leaders review design options.

Before: Eliminate the need to reach in or redesign guarding and process; provide safe interim isolation.

During: Check guard function in real production and speak with operators about pressure to bypass.

Hold or stop: Keep the machine stopped if guarding is defeated or interim protection cannot prevent access.

Completion and hand back: Approve restart only after competent verification, then sample future use and update the risk profile.

Evidence: Keep report, risk assessment, design decision, budget owner, stop/restart and effectiveness evidence.

Two sites with different risk patterns

Task, material and setting: A board sees frequent low-severity slips at one site and rare but severe containment-failure potential at another.

People and prerequisites: Risk advisers compare exposure, control confidence, worker reports and potential consequence rather than multiplying scores alone.

Before: Fix immediate slip causes and prioritise critical containment verification and emergency readiness.

During: Leaders assign owners and test control data during routine and non-routine tasks.

Hold or stop: Escalate any failed critical barrier regardless of injury history.

Completion and hand back: Review trend and field evidence, adjust resources and update profile after change.

Evidence: Keep scenario-based rationale, action owners, checks and post-change results.

What does good risk-management architecture look like?

A good architecture connects the high-level risk profile to task assessments, standards, controls, evidence and leadership review.

Risk architecture is the structure that keeps risk information flowing. It prevents a risk assessment being trapped in a site folder or a board dashboard becoming detached from real controls.

The test is traceability: can a top risk be traced down to field controls, and can a field failure be traced back up to leadership decisions?

Trace one decision from floor to board. A depot supervisor identifies repeated pedestrian-vehicle conflict and records the specific crossing and exposed people; the risk owner compares sites, funds physical separation and names the person who checks the route each shift. Leadership then reviews whether the barrier remains effective as deliveries change. Without this chain, a risk register can look complete while no one owns the control. HSE HSG65 connects planning, implementation, checking and action.

LayerPurposeExample
Board risk profileShows the most significant organisational risks, harm potential and control confidence.Work at height, transport, asbestos, violence, fire, occupational health or process safety.
Risk registerTracks significant risks, actions, owners and verification.High-risk action for traffic segregation with director owner.
Specialist assessmentAdds competent technical analysis where ordinary assessment is not enough.Fire risk assessment, COSHH monitoring, DSEAR, lifting plan, ergonomics or process safety study.
Standards and proceduresDefine minimum control expectations.Group standard for contractor control or isolation.
Task assessmentApplies standards to work as done.Site-specific RAMS, COSHH, DSEAR or lifting plan.
Critical controls and competenceMake safe work possible and identify what must not fail.Guarding, LEV, permit, supervision, equipment and training.
Assurance and reviewChecks that the system works.Critical-control checks, audits, dashboards and board review.

Worked example to download. Follow an organisational risk from its description through control ownership, assurance and review in the Crownway Fuels organisational risk register (XLSX). Compare the worked decisions with the separate blank sheets to structure your own register. The examples show planned controls; a target rating is not evidence that a control works. Run the discussion using the Risk register workshop guide (DOCX). These worked examples cover ten English forecourts, head-office/mobile support and a separately labelled illustrative bulk terminal. Use the blank sheets for your own organisation, checking its activities, jurisdiction and controls.

How should risk appetite and tolerance be handled?

Risk appetite must never be used to accept legal non-compliance or uncontrolled serious harm potential.

For the control decision, HSE’s risk assessment guidance explains why reasonably practicable measures must be taken; a company risk appetite cannot waive the duty. Record the site evidence and escalate where the control basis is uncertain.

Risk appetite is useful for business choices, but health and safety has hard boundaries. Legal duties, reasonably practicable control, recognised standards and foreseeable serious harm cannot be traded away because a business has a high appetite for commercial risk.

A mature organisation uses tolerance language carefully: intolerable risks are stopped, significant risks are reduced so far as is reasonably practicable, and residual risk is reviewed with evidence rather than hope.

Decision areaPoor useGood use
Legal complianceAccept non-compliance as a business risk.Treat compliance gaps as action and escalation items.
High-harm riskUse a matrix score to justify delay.Consider credible worst case and critical-control health.
ALARP decisionClaim controls cost too much without evidence.Use the safety-weighted test: reject an applicable further precaution only when its sacrifice in time, trouble and cost is grossly disproportionate to its risk-reduction benefit.
Temporary controlsLet temporary controls become normal.Set expiry, owner, review and verification.
Residual riskSign off because no incidents have occurred.Use assurance evidence and weak-signal review.
Board decisionApprove risk without seeing field evidence.Review top risk, control confidence and decision options.

Which indicators show whether risk management is working?

Useful indicators show control effectiveness, action quality, weak signals and management response.

A risk dashboard should not be dominated by injury counts. Good leading indicators show whether the controls that prevent serious harm are present, used and effective.

Indicators must be interpreted. A fall in near-miss reporting may be good, or it may mean people have stopped reporting. A green training metric may hide weak competence if nobody observes the task.

Choose an indicator that can trigger an action before injury. For the vehicle route, count failed barrier checks, unplanned pedestrian crossings and overdue repairs, then compare these with worker reports and observed traffic. A fall in reports is ambiguous if workers have stopped speaking up; verify the route in person before claiming improvement. The manager should record the decision, temporary restriction and later effectiveness check. HSE workplace transport guidance gives the task context.

IndicatorWhat it showsChallenge question
Critical-control verificationWhether high-harm controls are working.Are checks sampling the right controls?
Overdue high-risk actionsWhether risk reduction is drifting.Who owns the delay and what temporary controls exist?
Repeat findingsWhether root causes are being fixed.Is this a system weakness rather than local non-compliance?
Worker concernsWhether weak signals are surfaced.Do people get feedback after reporting?
Maintenance backlogWhether asset risk is increasing.Which backlog items affect critical controls?
Health surveillance statusWhether occupational health controls are being monitored.Are exposure failures being linked to task controls?

Why is a risk matrix not risk management?

A matrix can support prioritisation, but it does not select controls, allocate ownership, verify effectiveness or make legal decisions defensible.

Risk matrices can be useful when they prompt discussion, but they become dangerous when the score replaces judgement. A low number can hide fatal exposure if the scenario is poorly described, and a high number can still be useless if no one owns the control improvement.

A professional risk-management conversation asks: what is the credible harm scenario, what control prevents it, how strong is that control, who owns it, what evidence proves it works, and when does the issue need escalation for design, budget or specialist help?

QuestionMatrix-only answerRisk-management answer
What could go wrong?A hazard label and score.A credible scenario with people, harm route and control failure.
How good are the controls?Assumed from existing paperwork.Verified through observation, inspection, monitoring or audit evidence.
Who owns improvement?Action noted on assessment.Named risk owner with authority, resource and deadline.
What needs escalation?Only red risks.Fatal/major-harm potential, weak critical controls, legal uncertainty and resource barriers.
How is closure proved?Score reduced.Control installed, briefed, maintained and field-verified.
What does leadership see?Counts of assessments completed.Top risks, control confidence, overdue actions and decisions required.

How should a supervisor escalate a risk that needs design or budget change?

When a critical control fails or a safer design needs budget beyond a supervisor’s authority, stop or restrict the affected work, provide interim protection and escalate the risk, options, owner and decision deadline to leadership. Restart only after competent verification; record whether the change works in real use.

A warehouse supervisor notices pedestrians walking behind reversing vehicles because the marked walkway crosses a loading doorway. The supervisor stops the conflicting vehicle movement and establishes a verified safe interim arrangement while layout redesign, barriers and delivery timing are assessed. A trained authorised banksman is an option only where suitable stronger measures cannot be used, with a safe position, agreed signals and a stop-on-loss-of-contact rule; a briefing alone does not authorise restart.

A weak system leaves the supervisor carrying the risk locally. A strong system turns the concern into a risk-register item with interim controls, design options, cost/resource decision, senior owner and verification after the layout changes.

StepSupervisor actionManagement-system output
RecogniseIdentify that worker behaviour is being shaped by poor layout.Risk concern recorded with photos and task observation.
Control temporarilySet temporary segregation, briefing and supervision.Interim control recorded with expiry and owner.
EscalateRaise that permanent control needs spend/design authority.Risk-register action assigned to manager or director.
DecideCompare design options and reasonably practicable risk reduction.Budget decision and ALARP rationale.
ImplementInstall barrier, gate, route change or delivery control.Updated traffic plan and briefing.
VerifyObserve work at peak times and review near misses.Control verification and dashboard update.

How does risk management look in different sectors?

The same risk-management logic applies across sectors, but the controls, evidence and escalation routes differ.

Sector examples help learners avoid treating risk management as an abstract framework. Each setting has its own high-harm scenarios, vulnerable controls and evidence needs.

The test is whether the organisation can see its top risks and prove that the controls are suitable for the work as done.

A construction lifting plan, a hospitality kitchen allergen process and a logistics vehicle route need different technical controls, but the same management question follows each: what serious harm could occur, which control prevents it, who checks it and what happens if it fails? The person closest to work identifies deviations; the risk owner resolves changes beyond local authority; assurance tests the result. Do not copy a numerical risk score from one sector to another without the actual scenario and control evidence. HSE managing-risk guidance describes the underlying process.

SectorHigh-value risk-management focusEvidence that shows control
ConstructionWork at height, lifting, excavations, plant/pedestrian interface, silica and contractor control.construction phase plan (CPP), RAMS, permits, inspection records, supervisor checks and assurance visits.
LeisurePool safety, slips, safeguarding interface, fire, Legionella, manual handling and lone work.Operating procedures, training, water checks, inspection logs and incident trends.
ManufacturingMachinery guarding, maintenance, isolation, noise, ergonomics and forklift movements.Provision and Use of Work Equipment Regulations (PUWER) inspections, lockout records, guarding checks, noise controls and defect trends.
Process safetyLoss of containment, ignition, overpressure, alarms, MOC, bypasses and emergency response.process safety information (PSI), hazard and operability study (HAZOP) / layer of protection analysis (LOPA) actions, barrier verification, management of change (MOC) records and process safety indicators.
Healthcare or careMoving and handling, violence, infection prevention, medicines, fatigue and vulnerable people.Care plans, staffing review, training, incident learning and infection-control audits.
LogisticsDriving, load security, fatigue, yard movements, loading/unloading and contractors.Driver checks, telematics, journey planning, loading plans and yard audits.

When should risk management decisions be escalated?

Escalation is needed when risk is serious, uncertain, cross-functional, resource-dependent or outside local authority.

Risk escalation should not be a sign of failure. It is a normal part of competent management. Supervisors should not be expected to accept residual risk that requires design change, capital spend, legal interpretation, specialist assessment or operational shutdown.

Clear escalation rules help prevent drift. If a critical control fails, a statutory inspection is overdue, a serious risk has no owner or work has changed beyond the assessment, the system should force a management decision.

TriggerEscalation routeDecision required
Fatal or major-harm potentialSenior manager or risk owner.Stop, redesign, resource or temporary control.
Legal uncertaintyH&S lead, HR/legal or specialist adviser.Interpret duty and agree evidence.
Specialist hazardTechnical authority or competent person.Survey, monitoring, design or assessment.
Cross-site patternFunctional lead or board review.Group standard or campaign.
Resource constraintBudget holder or director.Approve risk reduction or interim control.
Repeated weak signalManagement review.Investigate system cause and verify actions.

Apply the safety-weighted ALARP decision

Where the reasonably practicable test applies, the comparison is weighted toward safety. An otherwise applicable further precaution may be rejected only if its sacrifice in time, trouble and cost is grossly disproportionate to its risk-reduction benefit. Inability to afford it or management preference is not that demonstration. Ordinary tasks do not automatically require a numerical cost-benefit study.

Illustrative reversing-route entry: the transport owner compares removing the crossing, fixed segregation and interim traffic controls against the credible crush harm and evidence of overlap. A resource constraint remains an unresolved leadership decision, with vehicle movement restricted; it does not make the barrier unnecessary. Record the chosen design, evidence, approver, interim control and verification date. Reopen on a failed gate, late-delivery conflict or unproved safeguard.

HSE risk steps; HSE reasonably practicable explanation (HSG71, paragraph 94).

Where does risk management commonly fail?

It fails when paperwork replaces control, matrices replace judgement or leaders see lagging data without control confidence.

Weak systems look tidy but do not change work. They have risk assessments, registers and dashboards, but workers cannot explain controls, actions are overdue, and leaders do not see serious-risk indicators.

Another failure is overconfidence in low accident numbers. A site can have few injuries while serious risks are worsening through poor maintenance, contractor drift, fatigue, health exposure or uncontrolled change.

Failure or weak practiceHow it developsWhat good looks like
Matrix-driven thinkingRisk score becomes more important than scenario and control.Use scenario, harm potential, controls and evidence before score.
Generic assessmentsCopied forms do not match work.Observe work and involve workers.
No action verificationActions closed by email or memory.Require evidence for high-risk close-out.
Leadership blind spotBoard sees injuries but not critical controls.Report top risks, assurance confidence and weak signals.
Change driftNew people, process or equipment not assessed.Use MOC and review triggers.
Health risk underweightingDust, noise, stress or MSD risks treated as lower priority.Profile occupational disease and exposure with the same discipline as acute safety.

What evidence should risk management hold?

Evidence should show risk information, control decisions, ownership, implementation, verification and learning.

Risk assessments and method statements (RAMS) should reflect real work. Risk management evidence should be useful before an incident, not assembled after one. It should help managers decide what to do now, and it should help auditors test whether the system is alive.

For Diploma-level learners, the evidence question is central: how would you prove the control was selected, implemented, communicated, monitored and reviewed?

Evidence itemWhat it should showAssurance question
Risk assessment or technical assessmentScope, hazards, affected people, controls, residual risk, owners and review triggers.Does it match the work as done?
Action trackerActions, owners, dates, priority, temporary controls and close-out evidence.Are high-risk actions verified, not merely marked complete?
Training and briefing recordsWho was briefed, on what, when and how understanding was checked.Can workers explain the controls in practice?
Inspection and monitoring recordsPlanned checks, defects, findings, trends and corrective action.Are checks sampling critical controls?
Incident and near-miss learningEvents, weak signals, investigations and improvement actions.Are repeated signals driving system change?
Management reviewTrend, assurance confidence, resources and decisions.Are leaders seeing the right risk picture?
Risk profileTop risks, harm potential, exposure and control confidence.Does leadership see serious-risk priorities?
ALARP rationaleOptions considered and why further controls were or were not reasonably practicable.Is the decision evidence-based?
Risk registerOwners, actions, due dates, residual risk and review triggers.Are risks being actively managed?

How should risk management be assured?

Assurance should test whether the system controls real work, not just whether documents exist.

Assurance should follow the risk. A high-risk control should receive more verification than a low-risk administrative task. The three-line model helps: supervisors verify work, managers and H&S advisers provide assurance, and independent or specialist review tests the system.

Field evidence matters. Risk management is only credible when the assessment, control, worker briefing and observed work tell the same story.

Assurance checkWhat good looks likeEscalate if
Risk profile reviewTop risks reviewed by leaders with control confidence.Risk profile is old or injury-only.
Assessment qualityAssessments describe real scenarios and controls.Generic hazards and copied controls dominate.
Worker understandingWorkers know critical controls and stop triggers.Controls are unknown or impractical.
Action close-outHigh-risk actions have verified evidence.Actions close by email or date change.
Change managementChange triggers reassessment.Temporary changes become normal.
Learning loopIncidents and audits update risk controls.Repeat findings recur without system change.

How should the work be managed and checked?

Use an accountable plan, practical controls, worker input and checks that show whether the controls work in real tasks.

HSE’s Plan, Do, Check, Act approach connects the risk decision to implementation, monitoring and improvement. For this topic, the duty holder should name a control owner, define the evidence that the control is effective, and change the work if that evidence fails. A management-system label or certificate is not proof that an individual exposure or task is safe. HSE managing health and safety

Official guidancePractical decisionBoundary
HSE Plan, Do, Check, ActAssign the risk owner, implement the chosen control and review field evidence after change or failure.This guidance does not replace the applicable GB or NI law, task assessment or named specialist decision.

What training and competence are needed?

Match practice and assessment to the person’s decision: workers recognise concerns; managers act on controls; specialists advise within their discipline; leaders verify outcomes.

Use observed scenarios, identify the assessor and record what was demonstrated. Reassess after a changed task, failure or new legal or technical information; do not invent a universal certificate expiry.

A worker should recognise a failed barrier and know where to report it; a supervisor should demonstrate a safe hold and a task assessment; the risk owner should select and resource a stronger control across sites. A reviewer tests whether the register, work method and physical route agree. Record observed practice and the changed decision, then reassess after a new layout, contractor flow or failed control. A completed risk matrix is not competence evidence.

Role-specific competence and verification
RolePractice and assessmentAssessorDemonstrated evidence and recordReassessment trigger
Worker and representativeReport actual work, deviations and weak controls; test whether changes are usable.SupervisorIdentify local risk changes and a practical worker concern; record assessor, observed task and escalation.Changed task, repeated concern or failed control.
SupervisorPrioritise immediate protection, owner and escalation when design or resources exceed local authority.Competent risk assessorApply a generic assessment to actual conditions and make a dynamic stop/reassess decision; record the scenario and assessor.Unexpected condition, near miss or assessment mismatch.
Risk assessor and specialistDescribe credible harm and control hierarchy, uncertainty and specific-regime boundaries.Lead assessor or specialistSelect generic, specific, dynamic or quantified method and justify data limits; retain assumptions, controls and review.New data, changed severity, disputed assumptions or failed control.
Senior leaderCompare significant risk profile, resource decisions and critical-control evidence across sites.Board or senior safety leadPrioritise high-consequence risks, assign resources and test source controls; record decision and effectiveness evidence.Repeat event, emerging risk or failed assurance.
AuditorSample controls in use and action effectiveness, not merely completed forms.Audit leadSample whether stated controls work in the field and challenge false precision; record assessor, evidence and corrective action.Unreliable data, overdue action or repeat weakness.

What do the acronyms and key terms mean?

Use these terms to explain a work decision, not as proof that a control is effective.

Acronyms and terms
TermExpansionMeaning for this topic
ALARPAs low as reasonably practicableRisk-reduction judgement, not a numerical matrix result.
Risk profileOrganisation-wide significant-risk pictureIncludes high-consequence and chronic-health risk.
Residual riskRisk after controlsMust be reviewed against actual control performance.
Critical controlBarrier essential to prevent major harmRequires accountable verification.
AssuranceEvidence that intended controls workDistinct from paperwork completion.
H&SHealth and safetyWorkplace health and safety, including occupational illness.
RAMSRisk assessments and method statementsTask records that should reflect actual controls and work as done.
CPPConstruction phase planProject plan for construction health-and-safety arrangements, where applicable.
PUWERProvision and Use of Work Equipment RegulationsEquipment-safety legal route; check the applicable jurisdiction and task.
PSIProcess safety informationMaterial, plant and process evidence for major-hazard decisions.
HAZOPHazard and operability studyStructured study of deviations and safeguards for suitable processes.
LOPALayer of protection analysisMethod to evaluate independent safeguards with stated assumptions.
MOCManagement of changeReview hazards, controls and authority before process or organisational change.
HSE hierarchyElimination, substitution, engineering controls, administrative controls, then PPEA source-first order for choosing workplace controls; keep higher-order measures ahead of instructions or PPE.
PPEPersonal protective equipmentResidual protection or visibility aid; it does not replace a feasible safer route or physical separation.
ERICPDEliminate, Reduce, Isolate, Control, Personal Protective Equipment, DisciplineCompare source removal and substitution with engineered separation before work rules or PPE; Discipline means checking that stronger controls keep working.

Which Crownway Fuels documents support this topic?

Open an editable document, read the preview, or find its place in the Crownway hierarchy. 8 resources relate to this page.

Fictional Crownway Fuels examples for English forecourts, with a separate illustrative bulk terminal. Check site applicability, permissions and actual controls before adapting any document for use.

Risk assessment and safe operating limits policy (8)
  • Risk assessment and safe operating limits policy (CWF-POL-RISK · Completed fictional example)

    Set company expectations, responsibilities and resources for risk assessment and safe operating limits.
    Read preview · Download DOCX · Show in hierarchy

  • Risk assessment and safe operating limits procedure (CWF-PRO-RISK · Completed fictional example)

    Explain who does what, in what sequence, the control rationale, evidence, escalation and safe restart conditions.
    Read preview · Download DOCX · Show in hierarchy

  • Site baseline health safety and environmental assessment (CWF-RA-RISK-01 · Blank editable master)

    Provide the site/task-specific site baseline health safety and environmental assessment and retain its controlled output.
    Read preview · Download DOCX · Show in hierarchy

  • Task specific fuel operations risk assessment (CWF-RA-RISK-02 · Blank editable master)

    Provide the site/task-specific task specific fuel operations risk assessment and retain its controlled output.
    Read preview · Download DOCX · Show in hierarchy

  • Task risk assessment and method statement (CWF-RAMS-RISK-01 · Blank editable master)

    Provide the site/task-specific task risk assessment and method statement and retain its controlled output.
    Read preview · Download DOCX · Show in hierarchy

  • Pre start and dynamic change check (CWF-CHK-RISK-01 · Blank editable master)

    Provide the site/task-specific pre start and dynamic change check and retain its controlled output.
    Read preview · Download DOCX · Download PDF · Show in hierarchy

  • Safe operating limits and alarm response register (CWF-REG-RISK-01 · Blank register with separate fictional worked entries)

    Provide the site/task-specific safe operating limits and alarm response register and retain its controlled output.
    Read preview · Download XLSX · Show in hierarchy

  • Operator briefing and understanding record (CWF-FRM-RISK-01 · Blank editable master)

    Provide the site/task-specific operator briefing and understanding record and retain its controlled output.
    Read preview · Download DOCX · Show in hierarchy

Open the full Crownway library