Reactive monitoring learns from workplace accidents, near misses, ill health and failed controls after they occur. It traces the harmful energy or exposure, the people affected and the safeguards that did not work, including events where chance prevented injury. Protect people first, decide the correct GB or Northern Ireland reporting route, investigate causes and verify stronger controls before treating the case as closed.
Updated 2026-10-19Great Britain and Northern IrelandVersion 2.2
Understanding Reactive Monitoring
Reactive monitoring learns from workplace accidents, near misses, ill health and failed controls after they occur. It traces the harmful energy or exposure, the people affected and the safeguards that did not work, including events where chance prevented injury. Protect people first, decide the correct GB or Northern Ireland reporting route, investigate causes and verify stronger controls before treating the case as closed.
Why this matters at work
The evidence set should include event narrative, credible worst consequence, barrier status, potential-severity rationale, peer challenge and escalation decision. Unsafe shortcut: ranking a dropped load that narrowly missed people as trivial because no injury occurred. Escalate when potential fatality, major accident, multiple casualty, irreversible disease or major environmental harm was credibly possible. Where evidence is incomplete, keep the conclusion conditional and control the residual risk rather than forcing certainty.
Set investigation effort using both what happened and what could credibly have happened. Base potential severity on the actual energy or exposure, people plausibly present, failed and surviving safeguards, and one or more realistic changes in conditions. Avoid giving every small deviation an imaginary catastrophic outcome, but do not classify a narrowly missed fatal exposure as trivial merely because nobody was hurt. Repeated events and incomplete evidence can also justify deeper investigation. Record the event narrative, scenario, barrier state, affected population, uncertainty and reasons for the investigation level. Obtain suitable challenge where the potential consequence is serious or disputed. Make safe the current work while the evidence is gathered and check external reporting separately. The selected scope should allow the team to examine immediate, underlying and organisational causes relevant to the failure. If later evidence changes the credible potential, revise the classification and investigation rather than preserving an early low score to meet a closure target.
How organisations manage this in practice
The evidence set should include a controlled scope statement, responsibility map, event taxonomy, escalation matrix, legal register, data dictionary and review cycle. Unsafe shortcut: treating reactive monitoring as an accident-counting exercise or as a substitute for preventive risk control. Escalate when a serious event, high-potential near miss, emerging health pattern or critical-control failure falls outside the reporting system. A competent reviewer should be able to reconstruct the event, evidence, causal reasoning, selected controls, action closure and effectiveness decision.
The evidence set should include risk-control map, leading and lagging indicators, inspection and test results, event data, thresholds and management review records. Unsafe shortcut: presenting a low injury count as proof of effective control without checking exposure, underreporting or critical-control performance. Escalate when lagging data improve while active checks, assurance coverage, worker reports or barrier condition deteriorate. Closure requires evidence that the control exists and functions; completion of a task or issue of a procedure is not enough.
An investigation report is passive learning until its findings change practice and are checked. Preserve the lesson’s mechanism, affected equipment or task, accountable recipient, required change and verification. Review handovers, contractor interfaces and personnel changes so the organisation retains the lesson after the original investigators leave. Source basis: HSE learning organisations.
One near miss can create parallel duties
Immediate protection, statutory reporting where required, and investigation can need action together. Reporting must not wait simply because causal analysis is unfinished.
Protect people now
Make the situation safe through the competent site arrangements and preserve relevant evidence without creating further exposure.
Check reporting independently
The responsible person checks the applicable GB or NI categories, thresholds and deadlines from current official guidance.
Investigate and improve
Test evidence, select stronger controls and name an owner and acceptance test; a low injury count does not prove control health.
Verify and share
Keep the action open until controls work in real use, then return learning to similar tasks. Numbered signal types are categories, not incident counts.
Read the complete task-specific control examples
ERICPD is a planning cross-map: Discipline verifies and sustains every control. ESEAP compares effectiveness. A label does not authorise the task; retain the owner, evidence and stop or change decision.
Lifting pallets after a dropped-load near miss · ERICPD
Eliminate
Remove the need for the suspended-load movement by changing delivery or stock layout where feasible.
Reduce
Use a suitable alternative load unit or handling method that prevents the identified instability after an assessed trial.
Isolate
Keep people outside the lifting/drop zone and secure the affected equipment and damaged load against reuse.
Control
Provide suitable rated lifting equipment, load restraint and stable support; investigate attachment and pallet condition.
PPE
Use task-assessed head, hand and foot protection; PPE cannot protect a person underneath a falling load.
Discipline
Verify equipment repairs and the revised load-handling method under controlled conditions before closing the finding.
Lifting pallets after a dropped-load near miss · ESEAP
Elimination
Remove the need for the suspended-load movement by changing delivery or stock layout where feasible.
Substitution
No separate approved substitution is specified; assess a genuinely safer material or process before relying on lower controls.
Engineering controls
Use a suitable alternative load unit or handling method that prevents the identified instability after an assessed trial.
Administrative controls
Reassess the lift plan, load information, competence and communication using evidence from the near miss.
PPE
Use task-assessed head, hand and foot protection; PPE cannot protect a person underneath a falling load.
Reviewing powder use after breathing complaints · ERICPD
Eliminate
Remove or suspend the changed powder process where feasible and restore a suitable assessed alternative.
Reduce
Trial a suitable lower-hazard formulation or non-dusty form after reviewing respiratory, skin, fire and product-quality risks.
Isolate
Separate the affected process from nearby workers and prevent contaminated dust spreading through the workplace.
Control
Verify enclosure, extraction and cleaning against the actual new material and rate of use.
PPE
Select adequate suitable RPE and other protection for remaining exposure; PPE does not replace fixing failed source control.
Discipline
Check corrective action in normal work, review further health reports and retain the authorised restart evidence.
Reviewing powder use after breathing complaints · ESEAP
Elimination
Remove or suspend the changed powder process where feasible and restore a suitable assessed alternative.
Substitution
Trial a suitable lower-hazard formulation or non-dusty form after reviewing respiratory, skin, fire and product-quality risks.
Engineering controls
Separate the affected process from nearby workers and prevent contaminated dust spreading through the workplace.
Administrative controls
Investigate the change and exposure route, involve workers and occupational health, and agree evidence needed before restarting.
PPE
Select adequate suitable RPE and other protection for remaining exposure; PPE does not replace fixing failed source control.
Who should use this reactive monitoring page?
Workers, supervisors, managers and investigators use reactive monitoring to learn from harm, near misses and failed controls, then verify that corrective action prevents recurrence.
A reporter needs an easy route and prompt feedback. A supervisor needs to make the area safe and preserve facts. The organisation’s responsible person checks statutory notification. An investigator examines how work and controls actually operated, while managers resource the correction and test its effect.
This page covers Great Britain and Northern Ireland. It is an operational learning guide, not a substitute for the site emergency plan, an investigation of a real event, medical advice or an event-specific legal reporting decision.
How can this guidance help in practice?
Workers and people carrying out the task
Use the Reactive Monitoring guidance to recognise relevant hazards, understand the precautions and identify when to stop, report a problem or ask for competent support.
Supervisors and managers
Use the task examples and control checks to plan work, brief the team, check implementation and assign improvements with owners and follow-up.
Safety, health, risk and assurance professionals
Use the explanations, sources and operational examples to develop assessments, audits and control verification. Check the actual scope and jurisdiction before applying a duty.
Learners, trainers and organisational decision makers
Use the definitions and examples to connect theory with workplace decisions, build briefings and ask informed questions. This page does not certify competence or authorise work.
What is reactive monitoring?
Reactive monitoring collects and acts on evidence of accidents, near misses, ill health, damage and control failures after they occur. Its purpose is to understand how risk escaped control and prevent recurrence.
Best-practice guide · six simple steps
Best-practice guide: Reactive Monitoring
Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.
What is reactive monitoring?
Avoid / redesign
Remove the need for the suspended-load movement by changing delivery or stock layout where feasible.
Control the task
Keep people outside the lifting/drop zone and secure the affected equipment and damaged load against reuse.
Verify before release
If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls.
Reactive monitoring collects and acts on evidence of accidents, near misses, ill health, damage and control failures after they occur. Its purpose is to understand how risk escaped control and prevent recurrence. Reactive monitoring learns from workplace accidents, near misses, ill health and failed controls after they occur.
Apply it: Which part of this plan would you check at the workface before authorising the task?
Turn reactive monitoring knowledge into a decision
Change at source
Remove the need for the suspended-load movement by changing delivery or stock layout where feasible.
Make it observable
If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls.
Keep useful evidence
Retain facts, images or logs, witness accounts, statutory-reporting decision, causal analysis, selected higher-order controls, owner, verification and later effectiveness review.
Reactive monitoring learns from workplace accidents, near misses, ill health and failed controls after they occur. It traces the harmful energy or exposure, the people affected and the safeguards that did not work, including events where chance prevented injury. Retain facts, images or logs, witness accounts, statutory-reporting decision, causal analysis, selected higher-order controls, owner, verification and later effectiveness review.
Apply it: What evidence would show that the change improves this task, rather than only completing a record?
At an illustrative construction site, a suspended package drops into a temporarily open walkway.
Act
Stop the lifting activity, protect anyone at risk, keep the area controlled and preserve available evidence without compromising immediate safety.
Hold / review
Keep the lifting operation on hold if the load path, equipment, exclusion boundary or cause is uncertain.
Triage the event by credible crush potential and possible statutory dangerous-occurrence criteria, not by zero actual injury. A competent investigator reconstructs the sequence, load path, barriers, supervision, contractor interface and equipment condition. The authorised site owner accepts a revised lifting and access arrangement only after required equipment and boundary checks, worker briefing and confirmation that interim actions are closed or controlled.
Apply it: At which point would you hold this example, and what evidence would allow it to proceed?
A dropped load lands near a worker in a construction area.
A vehicle crosses a pedestrian route in a warehouse.
A collision could cause crushing, fracture or fatal injury.
Repeated wet-floor falls or near falls in hospitality.
Slip energy can cause sprains, fractures or head injury; a similar event may affect a visitor.
Exposure route 1: A dropped load lands near a worker in a construction area. A vehicle crosses a pedestrian route in a warehouse.: A collision could cause crushing, fracture or fatal injury. Repeated wet-floor falls or near falls in hospitality.: Slip energy can cause sprains, fractures or head injury; a similar event may affect a visitor.
Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?
Remove the need for the suspended-load movement by changing delivery or stock layout where feasible.
Substitution
No separate approved substitution is specified; assess a genuinely safer material or process before relying on lower controls.
Engineering controls
Use a suitable alternative load unit or handling method that prevents the identified instability after an assessed trial.
Administrative controls
Reassess the lift plan, load information, competence and communication using evidence from the near miss.
PPE
Use task-assessed head, hand and foot protection; PPE cannot protect a person underneath a falling load.
Eliminate: Remove the need for the suspended-load movement by changing delivery or stock layout where feasible. Reduce, including substitution: Use a suitable alternative load unit or handling method that prevents the identified instability after an assessed trial. Isolate: Keep people outside the lifting/drop zone and secure the affected equipment and damaged load against reuse. Control: Provide suitable rated lifting equipment, load restraint and stable support; investigate attachment and pallet condition. Control: Reassess the lift plan, load information, competence and communication using evidence from the near miss. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.
Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?
Keep the action open until controls work in real use, then return learning to similar tasks. Numbered signal types are categories, not incident counts.
Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status.
Apply it: Which official source and full-topic section will you use to resolve the next decision?
Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains a workplace image with separate learning notes. Read the full topic for sources and further detail.
Read all six steps as text
1. What is reactive monitoring?
Reactive monitoring collects and acts on evidence of accidents, near misses, ill health, damage and control failures after they occur.
Avoid / redesign: Remove the need for the suspended-load movement by changing delivery or stock layout where feasible.
Control the task: Keep people outside the lifting/drop zone and secure the affected equipment and damaged load against reuse.
Verify before release: If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls.
Reactive monitoring collects and acts on evidence of accidents, near misses, ill health, damage and control failures after they occur. Its purpose is to understand how risk escaped control and prevent recurrence. Reactive monitoring learns from workplace accidents, near misses, ill health and failed controls after they occur.
Apply it: Which part of this plan would you check at the workface before authorising the task?
2. Turn reactive monitoring knowledge into a decision
Use the evidence to improve the actual work arrangement.
Change at source: Remove the need for the suspended-load movement by changing delivery or stock layout where feasible.
Make it observable: If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls.
Keep useful evidence: Retain facts, images or logs, witness accounts, statutory-reporting decision, causal analysis, selected higher-order controls, owner, verification and later effectiveness review.
Reactive monitoring learns from workplace accidents, near misses, ill health and failed controls after they occur. It traces the harmful energy or exposure, the people affected and the safeguards that did not work, including events where chance prevented injury. Retain facts, images or logs, witness accounts, statutory-reporting decision, causal analysis, selected higher-order controls, owner, verification and later effectiveness review.
Apply it: What evidence would show that the change improves this task, rather than only completing a record?
3. A dropped load with no injury but high potential
Example: a practical application of the existing topic lesson.
Setting: At an illustrative construction site, a suspended package drops into a temporarily open walkway.
Act: Stop the lifting activity, protect anyone at risk, keep the area controlled and preserve available evidence without compromising immediate safety.
Hold / review: Keep the lifting operation on hold if the load path, equipment, exclusion boundary or cause is uncertain.
Triage the event by credible crush potential and possible statutory dangerous-occurrence criteria, not by zero actual injury. A competent investigator reconstructs the sequence, load path, barriers, supervision, contractor interface and equipment condition. The authorised site owner accepts a revised lifting and access arrangement only after required equipment and boundary checks, worker briefing and confirmation that interim actions are closed or controlled.
Apply it: At which point would you hold this example, and what evidence would allow it to proceed?
Connect the task, the route to the person and the control that can fail.
Exposure route 1: A dropped load lands near a worker in a construction area.
A vehicle crosses a pedestrian route in a warehouse.: A collision could cause crushing, fracture or fatal injury.
Repeated wet-floor falls or near falls in hospitality.: Slip energy can cause sprains, fractures or head injury; a similar event may affect a visitor.
Exposure route 1: A dropped load lands near a worker in a construction area. A vehicle crosses a pedestrian route in a warehouse.: A collision could cause crushing, fracture or fatal injury. Repeated wet-floor falls or near falls in hospitality.: Slip energy can cause sprains, fractures or head injury; a similar event may affect a visitor.
Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?
Control summary. Read the complete task-specific controls and checks in the linked topic.
Elimination: Remove the need for the suspended-load movement by changing delivery or stock layout where feasible.
Substitution: No separate approved substitution is specified; assess a genuinely safer material or process before relying on lower controls.
Engineering controls: Use a suitable alternative load unit or handling method that prevents the identified instability after an assessed trial.
Administrative controls: Reassess the lift plan, load information, competence and communication using evidence from the near miss.
PPE: Use task-assessed head, hand and foot protection; PPE cannot protect a person underneath a falling load.
Eliminate: Remove the need for the suspended-load movement by changing delivery or stock layout where feasible. Reduce, including substitution: Use a suitable alternative load unit or handling method that prevents the identified instability after an assessed trial. Isolate: Keep people outside the lifting/drop zone and secure the affected equipment and damaged load against reuse. Control: Provide suitable rated lifting equipment, load restraint and stable support; investigate attachment and pallet condition. Control: Reassess the lift plan, load information, competence and communication using evidence from the near miss. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.
Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?
Follow the official sources below and retain the task-specific evidence.
Official guidance: HSE HSG65 Managing for health and safety
Official guidance: HSE managing health and safety
Task decision: Keep the action open until controls work in real use, then return learning to similar tasks. Numbered signal types are categories, not incident counts.
Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status.
Apply it: Which official source and full-topic section will you use to resolve the next decision?
Simplified learning guide. Use the full topic and the actual work arrangements; existing technical-review and approval statuses still apply.
Practical guide: What is the difference between active and reactive monitoring?
Learning point: A planned guard check is active monitoring. A reported defect or near miss starts reactive learning. In both cases, compare the actual guard with the relevant standard and verify any correction before normal use.
CHECK BEFORE — Inspect the guard against its known acceptance criteria, with the machine in a safe condition.
REPORT FAILURE — Stop affected use, protect people and capture what happened.
VERIFY CONTROL — A competent person tests the correction and authorises return to use.
A report is the start of a chain: protect people, capture facts, assess actual and credible potential harm, decide whether the law requires notification, investigate proportionately, select stronger controls and verify they work. A low injury count can coexist with high potential severity, underreporting or weak safeguards. Active monitoring tests controls before harm; both views are needed.
Reactive monitoring itself is not the physical hazard. The underlying energy, substance, work organisation or failed barrier harms people. The examples below connect events to those mechanisms; a near miss is valuable because chance may be the only reason nobody was injured.
Repeated wet-floor falls or near falls in hospitality.
Slip energy can cause sprains, fractures or head injury; a similar event may affect a visitor.
Is the source removed or contained before reopening the route? HSE slip prevention
Several workers report breathing symptoms after a process change.
Airborne exposure may cause acute irritation or longer-term disease even without one accident event.
Are exposure controls checked and suitable health advice sought while information stays confidential? HSE COSHH assessment
How can the hierarchy of controls turn incident and ill-health findings into effective risk reduction?
Move from the event to a tested explanation, a stronger control and evidence that the control works in everyday work.
Fewer incidents. A higher rate.
Consecutive 12-month periods use the same incident definition. Counts fall from 8 to 6 (25%), while the average workforce falls from 400 to 200. The incident rate rises from 20 to 30 per 1,000 workers (50%). Consider hours worked when exposure patterns differ.
Why does the rate rise while the count falls?
The workforce denominator halves while incidents fall by only one quarter. Compare consistent periods, definitions and exposure.
Workforce-based incidence rates for equal periods. They do not adjust for hours worked, work mix, reporting changes or differences in exposure.
Start with care and scene safety. Preserve physical and digital evidence without putting anyone in danger. Separate direct observation, witness account, inference and unknown facts; invite workers and contractors to explain actual task conditions. HSE HSG245 sets out gathering information, analysing it, identifying risk controls, and making and implementing an action plan.
Look beyond the final action. A person walked into a route, but why was the route open, the barrier missing, the handover unclear or the vehicle schedule changed? Compare plausible explanations and seek disconfirming evidence. Assign an owner to each interim restriction and final correction. Close an action only after testing the installed control and checking whether it remains effective.
ERICPD (Eliminate, Reduce including substitution, Isolate, Control, Personal Protective Equipment, Discipline) is a useful six-stage control-planning framework, not a legal reporting category. Apply it to the underlying hazard found by the event. The strongest practicable control should address the actual mechanism; PPE and discipline cannot compensate for a known missing physical barrier.
Follow one illustrative near miss: a pedestrian steps through a missing gate into a forklift path and a driver brakes. Record the event, make the scene safe, and trace the missing gate and traffic design before choosing corrective action. ERICPD supports the action discussion; the HSE five-level hierarchy identifies whether a measure removes, substitutes, engineers or merely administers the hazard. Reporting compliance and a new briefing cannot replace a feasible physical correction. HSE control hierarchy.
On a narrow screen, scroll sideways for the source-control choice, verification and stop point.
Choose the activity that matches the work. Each has its own controls, verification and stop/restart decisions; ERICPD and ISO 45001 are alternative views of that same activity.
Choose the activity
A pallet load fell without injury. Preserve the report and inspect load, lifting method and equipment before another lift. Read the full task workflow.
How can the ERICPD hierarchy of controls reduce risks while lifting pallets after a dropped-load near miss?
Control level
Control for this activity
Owner and verification
Stop / restart decision
Eliminate
Remove the need for the suspended-load movement by changing delivery or stock layout where feasible.Sources and references
Release only after lifting owner accepts the tested corrective actions before further lifting. Retain the checks and unresolved restrictions at handover.
Keep the activity on hold while defects or required reinstatement evidence remain unresolved.
How can the ISO 45001 hierarchy of controls reduce risks while lifting pallets after a dropped-load near miss?
Release only after lifting owner accepts the tested corrective actions before further lifting. Retain the checks and unresolved restrictions at handover.
Keep the activity on hold while defects or required reinstatement evidence remain unresolved.
Workers report breathing problems after a material change. Hold the affected exposure route, provide appropriate health support and review the actual process. Read the full task workflow.
How can the ERICPD hierarchy of controls reduce risks while reviewing powder use after breathing complaints?
Control level
Control for this activity
Owner and verification
Stop / restart decision
Eliminate
Remove or suspend the changed powder process where feasible and restore a suitable assessed alternative.Sources and references
Release only after process owner accepts verified controls with occupational-health input as appropriate. Retain the checks and unresolved restrictions at handover.
Keep the activity on hold while defects or required reinstatement evidence remain unresolved.
How can the ISO 45001 hierarchy of controls reduce risks while reviewing powder use after breathing complaints?
Control level
Control for this activity
Owner and verification
Stop / restart decision
Elimination
Remove or suspend the changed powder process where feasible and restore a suitable assessed alternative.Sources and references
Release only after process owner accepts verified controls with occupational-health input as appropriate. Retain the checks and unresolved restrictions at handover.
Keep the activity on hold while defects or required reinstatement evidence remain unresolved.
How do controls change for breathing-symptom cluster after a material change?
This second pathway uses the same ERICPD prompt and the HSE five-level hierarchy. Each proposed control needs a competent feasibility decision and proof at the actual site. Official task guidance supports the method; the example does not authorise a particular installation.
On a narrow screen, scroll sideways for feasibility, proof and stop decisions.
How does reactive monitoring apply across sectors?
The reporting and learning chain is common, but the harmful agent, exposed people and effective control differ by task.
These are illustrative events, not claims that every site in a sector has the same risk. Triage should consider both the observed result and what could credibly have happened if a person or safeguard had been in a slightly different position. A common dashboard can compare themes; the corrective control must remain specific to the mechanism.
How the same learning chain transfers between sectors
Sector, signal and people
Potential harm and failed control
Immediate and longer-term decision
Construction: suspended material falls near a contractor.
Crush or fatal injury; exclusion zone or lifting plan may have failed.
Stop lifting, keep people clear, preserve evidence and review the lifting control before restart. HSE lifting operations
Logistics: forklift enters a pedestrian crossing.
Vehicle strike; physical segregation, route design or shift coordination may be weak.
Hospitality: repeated slips in a service corridor.
Fracture or head injury to workers or visitors; drainage, floor condition or spill response may be inadequate.
Control the route, investigate source, and verify a durable floor or drainage correction. HSE slip prevention
Manufacturing: several workers report breathing symptoms after material change.
Inhalation exposure may cause illness; ventilation or change control may have failed.
Check exposure controls and obtain suitable health advice, protect private records and review the change before continued use. HSE COSHH assessment
What do a high-potential near miss and a health pattern teach?
An event without injury may still expose a fatal pathway, while occupational ill health may appear as several weak signals rather than one accident.
A dropped load with no injury but high potential
Task, material and setting: At an illustrative construction site, a suspended package drops into a temporarily open walkway. Nobody is struck. The project has a lifting plan and a shared contractor access route.
People and prerequisites: The lifting supervisor, contractor workforce, site manager and any visitors near the route may be affected. Before work resumes, the responsible team needs the lifting equipment status, plan, exclusion arrangements and witness accounts.
Before: Stop the lifting activity, protect anyone at risk, keep the area controlled and preserve available evidence without compromising immediate safety. Record who was present and who controls the scene.
During: Triage the event by credible crush potential and possible statutory dangerous-occurrence criteria, not by zero actual injury. A competent investigator reconstructs the sequence, load path, barriers, supervision, contractor interface and equipment condition.
Hold or stop: Keep the lifting operation on hold if the load path, equipment, exclusion boundary or cause is uncertain. Immediate danger triggers the site emergency arrangements. The responsible person checks GB or NI notification using the applicable law; do not assume every dropped object is automatically reportable.
Completion and hand back: The authorised site owner accepts a revised lifting and access arrangement only after required equipment and boundary checks, worker briefing and confirmation that interim actions are closed or controlled.
Evidence: Retain facts, images or logs, witness accounts, statutory-reporting decision, causal analysis, selected higher-order controls, owner, verification and later effectiveness review.
Control source:HSE lifting operations. The site details are illustrative; verify the actual task and jurisdiction before release.
The construction example remains a high-potential learning event even if no statutory report is ultimately required. Reportability and investigation depth are distinct decisions.
Breathing symptoms after a material change
Task, material and setting: At an illustrative manufacturing site, three workers separately report breathing discomfort after a new material grade is introduced. There is no single dramatic spill or injury event.
People and prerequisites: Affected workers need support and suitable medical or occupational-health advice. The process owner, supervisor and competent exposure assessor need the material change record, work pattern and control information; clinical details stay with authorised people.
Before: Record each report respectfully, check whether exposure may be continuing, and apply proportionate interim restrictions or controls. Seek competent health and exposure advice rather than waiting for a statistical trend.
During: Examine material identity, ventilation performance, tasks, timing and comparable reports. Keep symptoms and private records separate from a widely shared incident narrative. The responsible person checks whether a diagnosed reportable disease and specified exposure criteria are met under the relevant GB or NI rules.
Hold or stop: If control performance is unknown or symptoms continue, restrict the affected process and escalate. Acute distress or suspected serious exposure follows medical and emergency arrangements. Do not conclude that the material is safe merely because no report under the Reporting of Injuries, Diseases and Dangerous Occurrences Regulations (RIDDOR) is yet required.
Completion and hand back: The process owner verifies the revised material or exposure control and obtains competent advice before normal use. Workers receive a clear explanation of controls without disclosure of someone else’s health information.
Evidence: Retain the change and exposure-control records, anonymised trend, assessment, medical advice held with lawful access, statutory-reporting decision, action test and effectiveness review.
Control source:HSE COSHH assessment. The site details are illustrative; verify the actual task and jurisdiction before release.
These worked examples provide decision logic only. Actual site restrictions, medical action, statutory classification and restart approval require the applicable procedures and competent judgement.
What should a reactive monitoring dashboard show?
Show potential harm, barrier condition, reporting coverage and action effectiveness alongside incident counts and rates.
Practical guide: How should a zero-injury dashboard change an operational decision?
Learning point: The zero is an illustrative outcome, not proof of a safe workplace. Review control condition, work exposure and reporting confidence together. A change in near-miss reporting can reflect trust or reporting practice as well as changes in risk.
DEFINE — Check the period, population and exposure behind the injury count.
COMPARE — Inspect overdue critical maintenance and repeated defects; listen to workers and test reporting confidence.
DECIDE — Restrict the affected route where needed, fund the physical correction and name the owner.
VERIFY — Test segregation in use and sample it again after work patterns change.
Practical guide: How do you read injury counts alongside defects and overdue actions?
Learning point: A near-miss count can change when trust, definitions or work exposure change. Verify the physical control and the reporting system before claiming that an improving headline means improving safety.
DEFINE — State the metric, population, period and work exposure.
TEST DATA — Check definitions, missing reports and confidence in reporting. Data unreliable? Consult workers, sample the work and repair the definitions or reporting route.
CHECK CONTROL — Compare the trend with actual barrier condition and real work. Critical control impaired? RESTRICT OR REPAIR NOW. Do not average away a serious outlier.
ACT ON RISK — Name a decision owner, restrictions and resources as needed.
VERIFY — Test whether the correction works during normal operations.
REVIEW — Check later evidence, repeat findings and feedback to reporters. Controls stable? Continue proportionate review and checks when work changes.
A low rate may mean few exposures, good controls, chance, underreporting or a small denominator. Record the definition and population behind each measure and explain changes in reporting routes or classification. Avoid safety triangles as a prediction that a fixed number of minor events leads to one serious accident.
A monthly count should lead to a control decision. If forklift near misses fall while pedestrian-route defects remain open, the manager should not infer that separation has improved; they should walk the route, check the physical barrier and review whether people still report weak signals. Record the owner and closure evidence for each critical correction, then sample the route again after work patterns change. HSE process-safety indicator guidance explains why outcome counts need to be read alongside control performance.
Signals a dashboard should show
Measure
Interpretation check
Actual and potential severity
Separate outcome from credible potential; show high-potential near misses and critical-control failures.
Report coverage and timeliness
Include workers, contractors, sites and health reports; a rise may reflect improved trust rather than worsening control.
Action and verification
Show interim restrictions, overdue critical actions, tests completed and effectiveness results, not only closure percentages.
Exposure and denominator
State work hours, tasks, people or relevant opportunity where a rate is used; flag small numbers and changed definitions.
Active control evidence
Compare event trends with inspections, maintenance, exposure checks and worker observations to challenge false assurance.
HSE HSG254 helps major-hazard sites develop process-safety indicators; its approach is useful for critical controls but does not create a universal target for every business. Protect individual health and witness data when sharing trend information.
What does a strong incident-to-learning pathway look like?
Each hand-off needs an owner and evidence, from immediate protection and legal classification through causal learning and a tested corrective control.
Practical guide: What evidence is needed before a corrective action is closed?
Learning point: Closure needs evidence that the correction controls the hazard, named acceptance and later effectiveness checks. An email, poster or completed form cannot substitute for a working physical safeguard.
PROTECT NOW — Maintain an interim restriction while the hazard is uncontrolled. Immediate danger? Isolate or restrict first. Do not wait for the permanent repair.
FIX CAUSE — Choose a source-first correction addressing the demonstrated causes.
NAME OWNER — Agree who delivers it, by when and the acceptance test.
TEST IN USE — Try the correction under realistic operating conditions. Test fails or is missing? KEEP OPEN. Correct the weakness and repeat a suitable acceptance test.
HAND BACK — A named competent person accepts evidence and briefs affected people.
TREND — Check the control keeps working and review similar work. Finding repeats? REOPEN cause analysis, check similar areas and update the risk assessment.
An organisation should define a route for workers, contractors and the public to report relevant events. It should keep statutory reporting distinct from the wider internal learning system. The duty manager may control immediate danger while another responsible person decides RIDDOR and a competent investigator scopes the causal work.
From event to verified learning
Step
Question and evidence
Protect and capture
Is anyone in danger? Provide care, control the scene and capture prompt facts from all affected work groups.
Classify and notify
What happened, what could credibly have happened, and which GB/NI statutory or sector route applies? Record the decision and owner.
Investigate
What sequence, failed barriers and work conditions explain the event? Separate fact from inference and test alternatives.
Choose and act
Which higher-order control addresses the mechanism? Assign resources, interim restrictions, owners and acceptance criteria.
Verify and learn
Has the change been installed and tested in real work? Check recurrence, transfer learning and update risk controls and management review.
Closing a task in software is not the same as proving that the hazard is controlled. Revisit the action after enough real work has occurred to see whether the new barrier survives normal shifts, maintenance and contractor interfaces.
What separates a weak investigation from a strong one?
A strong investigation reconstructs the event and tests how multiple controls and work conditions shaped it; a weak one stops at a blame label or first visible error.
“Worker failed to follow procedure” is a hypothesis, not a complete explanation. Ask whether the procedure matched the job, whether equipment and time were available, what supervision and handover conveyed, and why the barrier was vulnerable. Interview people without blame, document uncertainty and allow a competent reviewer to challenge causal statements.
The corrective measure must follow the causal finding. If the route is poorly designed, retraining alone leaves the collision risk. If a critical guard repeatedly fails, a reminder poster does not repair it. Record rejected options, interim restrictions, owners, commissioning evidence and the test that will show the new control works.
Investigation methods and worked examples
How can Fishbone and Five Whys help explore causes?
A fishbone, also called a cause-and-effect or Ishikawa diagram, places the event at its head. The main bones group possible contributors; smaller branches explore what led to each one. Categories are prompts to investigate, not findings.
Fishbone: explore the wider picture
Use it when several things may have contributed. Start with categories such as people, equipment, methods, materials, environment and management; rename them to suit the work. Add causes and subcauses without forcing a single chain.
Ask what led to a specific explanation. Branch when there is another reason, and stop where the evidence runs out. Five is a guide, not a target. Use the two methods together to examine a broad picture and its individual paths.
Define what happened, including the task, place and sequence. Keep the event separate from assumptions about why.
Gather accounts from people involved and add several possible explanations. Explore work conditions, equipment and management arrangements as well as individual actions.
Record supporting and contradictory evidence for each explanation. Keep untested ideas separate from accepted findings; add an open question where evidence is missing.
Review immediate, underlying and root causes from the evidence. A category, the final card or the depth of a branch does not decide the cause level.
Link actions to the supported causes, assign an owner and date, then check implementation and whether the action prevents recurrence.
Compare the worked examples
The two BuildOut reports examine the same invented excavator-arm/scaffold incident: 18 explanations and six actions. Their evidence references are fictional teaching records.
BuildOut fishbone
Six cause categories with subcauses, evidence checks and actions · 24 pages.
Triage immediate safety, potential severity, legal reporting, failed barriers and the investigation needed before routine work resumes.
Practical guide: What should happen after a near miss or failed control is reported?
Learning point: A serious near miss can require a strong response without an injury. Statutory reporting is one decision within the wider learning process. Do not wait for a completed cause analysis before making safe or meeting a reporting deadline.
MAKE SAFE — Protect people, stop affected work if needed and preserve the facts.
POTENTIAL HARM? — Assess credible consequences separately from the actual outcome. High potential? Escalate for senior, competent investigation even if nobody was hurt.
GB OR NI? — Identify the location and the responsible reporting person.
RIDDOR TEST — Apply the correct event category and time limit promptly. Criteria met? YES: report by the correct route. NO: still investigate and learn.
INVESTIGATE — Test immediate, underlying and root causes against evidence.
VERIFY — Correct controls, check similar tasks and confirm effectiveness. Fix unverified? Keep the action open. Brief affected people and test the control in use.
The first report may be incomplete. Keep classification open where injury, diagnosis, equipment failure or sector scope is unclear; revise it when facts improve and preserve the audit trail. Set prompt escalation for high-potential events and critical-control failures even if the statutory test is not met. Do not use one simple injury score to decide every case.
The first triage separates immediate danger from learning and legal reporting. Make the area safe and preserve the facts; a competent person then checks the actual event against the applicable GB or NI reporting route while an investigator tests failed controls. Do not wait for a polished root-cause report before making a time-sensitive reporting decision, and do not treat a submitted report as evidence that the control is restored. See HSE reporting timing and HSENI incident reporting.
Decisions to make at the first review
Question
Action and record
Is anyone in immediate danger or in need of care?
Protect people and call the relevant emergency or medical route. Preserve evidence only when safe.
What is actual and credible potential severity?
Describe the energy or exposure and the failed barriers. Escalate high potential even when actual injury is minor or absent.
Could statutory or sector notification apply?
Use the GB or NI legal route and responsible person; record the reasoning, notification and timing. Do not equate every near miss with a dangerous occurrence.
What interim restriction is needed?
Name the owner, affected task, condition for release and communication to workers and contractors.
What investigation is proportionate?
Set competence, independence, scope, evidence plan and worker involvement based on the actual and potential consequences.
Illustrative reporting triage record
Run immediate protection, legal reporting and causal investigation in parallel. The responsible person records jurisdiction, event time, incapacity or diagnosis information, category under review, next decision time, the current regulator source and submission reference. An investigation deadline does not extend a reporting deadline.
GB incapacity example: record the accident time as day 0 and check whether normal-work incapacity exceeds seven consecutive days; exclude the accident day and include non-working days. Where this category applies, notify within 15 days of the accident. NI example: separately check the over-three-day category and submit within 10 days. These are illustrative incapacity routes, not universal reporting periods. Qualifying fatalities, specified/major injuries and dangerous occurrences need prompt notification under their applicable route. The reporting owner checks the category without waiting for causal closure, retains confirmation, and rechecks if the facts change.
The system fails when people cannot report, serious potential is downgraded, cases are coded inconsistently, actions are weak or closure is accepted without a working control.
Underreporting can arise from difficult forms, retaliation fears, contractor exclusion or lack of feedback. Blame can suppress evidence about workload and design. A dashboard may hide worsening risks if denominators, case definitions, exposure, illness data or critical-barrier tests are missing. A due date is an escalation signal, not proof that an action has reduced risk.
Escalate repeated near misses, occupational-health patterns, disabled safeguards and long-open critical actions. Investigate the reporting system itself if major events appear only after outside complaints or regulator contact. Return the learning to workers and check that the corrective measure works on real shifts.
What evidence should reactive monitoring hold?
A reviewer should be able to trace a report from the original event to legal triage, causal reasoning, a tested control and a later effectiveness decision.
Retain enough detail to reconstruct what happened without circulating personal medical information unnecessarily. Link duplicate reports while preserving what each witness actually said. Record version changes to classifications, causal conclusions and actions rather than overwriting history.
Records that make learning reviewable
Record
What it should prove
Initial event and care record
Event identity, people, task, actual outcome, immediate control and support, with sensitive details restricted.
Triage and legal decision
Potential severity, failed barrier, GB/NI and sector applicability, responsible person, notification and timing.
Investigation record
Chronology, evidence sources, facts, uncertainty, causal alternatives and worker/contractor input.
Action and hand-back
Interim restrictions, stronger control selection, owner, acceptance criteria, installation and release authority.
Effectiveness and learning
Field test, recurrence check, risk-assessment update, cross-site communication and management decision.
Retention, access and disclosure rules depend on the record and lawful purpose. GOV.UK staff-records data protection recommends limiting access to sickness and injury details and using less intrusive absence records where practical.
How should reactive monitoring be assured?
Sample reports, investigations, decisions and field evidence to see whether people can report honestly and whether corrective controls remain effective.
Practical guide: How do you plan a check that can reveal a failed critical control?
Learning point: Set the pass or hold threshold before the check. A checklist adds value only when it can test a real control and trigger a protective decision. Use this active check to verify corrections arising from reactive monitoring.
NAME RISK — Identify the task, harmful energy or exposure and people at risk.
NAME CONTROL — Name the barrier that prevents or reduces the credible harm.
CHECK STANDARD — Use the relevant legal, technical or manufacturer requirement. Standard unclear? HOLD THE DESIGN. Seek competent advice before issuing the check.
COMPETENT CHECK? — Set the person, method, frequency and stop threshold. Competence missing? Arrange suitable support; a completed checklist cannot fill the gap.
PASS OR HOLD — Observe or test the real control against its acceptance criteria. Critical control fails? RESTRICT WORK NOW. Correct and verify; keep the finding open.
RECORD — Keep the evidence, decision, owner and next review.
Ask workers and contractors whether reports are easy to make and whether they receive feedback. Check that high-potential events reach leaders, statutory decisions are recorded, witness accounts are treated fairly, and engineering or physical controls are tested after installation. Compare repeat-event patterns with active inspections and critical-control checks.
Management should challenge overdue actions, repeated weak recommendations, changing injury definitions and apparently perfect performance that conflicts with worker experience. Close a system improvement only when reporting quality and risk control both improve, not merely when a dashboard is updated.
Which Great Britain and Northern Ireland duties may apply?
Reactive monitoring supports risk-management duties and statutory reporting, but the GB and NI RIDDOR tests and routes must be applied separately.
Practical guide: Which RIDDOR route applies in Great Britain or Northern Ireland?
Learning point: For the worker-incapacitation examples, exclude the accident day and include consecutive weekends and rest days. Other reportable categories have their own tests and timescales. The responsible person checks the actual work connection, event and jurisdiction; statutory reporting and internal learning run alongside each other. Source wording checked 18 October 2026.
NAME GB OR NI — Use the location of the event and the applicable reporting instrument.
GREAT BRITAIN — For qualifying work-related incapacity: over three consecutive days must be recorded; over seven consecutive days must be reported within 15 days of the accident.
NORTHERN IRELAND — For qualifying work-related incapacity: over three consecutive days must be reported within 10 days of the incident.
CHECK CRITERIA — Separately check deaths, GB specified or NI major injuries, diseases, dangerous occurrences and injuries to non-workers. A near miss is not automatically reportable.
REPORT IF REQUIRED — Use the correct responsible person, authority route and event-specific deadline; do not wait for the investigation to finish.
LEARN — Investigate proportionately, correct the control and verify effectiveness even where a statutory report is not required.
The table states a key jurisdiction difference. The responsible person should decide from the actual event, injury, diagnosis, work connection and relevant schedule. Reporting to the regulator is not the same as investigating a wider near miss or taking action on a failed control. For immediate danger, protect people first while the reporting decision is made promptly.
Over-seven-day worker incapacity is a GB reporting category; over-three-day injuries require record keeping under the GB regime. Check the actual facts and exemptions.
HSENI lists over-three-day work-related injury as a NI reporting category. Do not copy the GB over-seven-day trigger into NI.
Near miss versus dangerous occurrence
Only specified Schedule 2 dangerous occurrences are RIDDOR-reportable; a wider near miss can still require internal investigation.
Check the separate NI regulations and HSENI guidance for dangerous-occurrence categories; internal learning still covers wider near misses.
Other interfaces
Sector, permit, emergency and data-protection requirements may add routes depending on the event.
Check NI sector and enforcing-authority routes for the actual event; a single report may not satisfy every duty.
Apply the event-specific GB or NI reporting rules and any sector route before deciding a deadline or form. Share identifiable health information only where lawful and necessary for the decision.
How should the work be managed and checked?
Use an accountable plan, practical controls, worker input and checks that show whether the controls work in real tasks.
HSE’s Plan, Do, Check, Act approach connects the risk decision to implementation, monitoring and improvement. For this topic, the duty holder should name a control owner, define the evidence that the control is effective, and change the work if that evidence fails. A management-system label or certificate is not proof that an individual exposure or task is safe. HSE managing health and safety
Official guidance
Practical decision
Boundary
HSE Plan, Do, Check, Act
Assign the risk owner, implement the chosen control and review field evidence after change or failure.
This guidance does not replace the applicable GB or NI law, task assessment or named specialist decision.
Who needs competence for reactive monitoring?
Reporters need a trusted route; triage staff need risk and RIDDOR awareness; investigators need evidence and causal-analysis skill; managers must be able to challenge weak actions.
Practise the actual escalation for injury, near miss, ill health and critical-control failure. Investigators should know how to protect evidence, interview without blame, distinguish fact from inference, involve relevant workers and contractors, and select controls. The responsible person obtains event-specific legal advice where classification is uncertain. Train action owners to demonstrate installation and effectiveness, not merely to mark a task complete.
Choose instruction and supervised practice for the actual decision. The assessor records the demonstration and scope of authority; reassess after a change, failure or evidence that the control is not understood. A course alone does not authorise specialist work.
Role-specific learning and competence evidence
Role and learning
Demonstration and assessor
Record and reassessment trigger
Workers and contractors: recognise and report injury, near miss, illness or failed control.
Supervisor checks that a person can use the actual reporting and immediate-danger route.
Accessible briefing and feedback; revisit after route change or missed report.
Supervisors and triage staff: protect people, preserve facts and assess potential severity.
Safety lead samples a realistic first report, interim control and escalation decision.
Triage record and owner; reassess after a serious near miss or classification error.
Investigators: interview fairly, reconstruct events and test causal alternatives.
Competent investigation lead reviews an evidence plan, causal reasoning and control recommendation.
Investigation competence and peer review; reassess after complex case or weak findings.
Responsible persons: decide GB or NI statutory reporting for the actual event.
Legal or safety specialist checks a jurisdictional case and notification record.
RIDDOR decision and source used; reassess after law change or missed notification.
Managers and auditors: resource stronger actions and test their effectiveness.
Senior lead reviews a case through field verification and repeat-event challenge.
Action test, feedback and management decision; reassess after recurring control failure.
How could Riverside Leisure Ltd use reactive monitoring?
Riverside should connect staff, contractor and visitor events across its sites to a common triage and learning process while keeping each site’s hazards and private records distinct.
Practical guide: How can a failed pool check prevent opening and trigger learning?
Learning point: The pre-opening check is active monitoring. An unexpected result, alarm, complaint or near miss becomes a signal to review. Hold the affected pool closed until the local technical standard, competent interpretation and staffing conditions are satisfied; then record hand-back and share the lesson.
CHECK — Review the water result, plant status and lifeguard cover against the approved local procedure.
HOLD — Keep the affected pool closed while an unexplained result or failed control is resolved.
VERIFY BEFORE OPENING — Record competent acceptance, confirm cover and brief affected staff. No numerical water limit is invented in this example.
In this example company, a repeated wet-floor near miss at a pool corridor is recorded even though nobody is injured. The duty manager controls the route. The investigator checks drainage, cleaning times, footwear and footfall rather than closing the case with a “be careful” reminder. The facilities owner tests the physical correction during busy periods before hand-back.
A separate pattern of staff breathing symptoms is reviewed with occupational-health and exposure advice and restricted personal-data access. The manager compares events with active inspections, shares useful control lessons across sites and records GB or NI legal decisions for the actual premises. Riverside is illustrative and no event count or internal deadline is presented as a statutory threshold.
Which related SHARE pages may help?
Use these pages for the deeper investigation, reporting and active-assurance work that a short monitoring article cannot contain.
These answers separate learning from statutory notification, weak metrics and privacy decisions.
Does a near miss have to be reported to the regulator?
Not automatically. GB RIDDOR lists specified dangerous occurrences; NI has its own rules. Record and investigate serious potential internally even when no statutory notification is required.
Does a low accident rate prove the workplace is safe?
No. Small numbers, low exposure or underreporting may mask weak barriers. Compare outcome data with active checks and worker reports.
Can retraining alone close an investigation?
Only if it addresses the proven cause and stronger feasible controls have been considered. Test the actual corrective measure in work before closure.
Can health details go on a general incident dashboard?
Use only the information needed for the purpose and restrict identifiable health or injury details. Aggregated trends may support learning without broad disclosure.
Is the RIDDOR over-seven-day rule the same in Northern Ireland?
No. GB and NI have separate instruments. HSENI lists over-three-day injury reporting in NI; the responsible person must use the correct territorial route.
Which official sources support this guidance?
These direct regulator, legal and privacy links support event learning and the distinct GB and Northern Ireland reporting decisions.
Government guidance for the applicable work decision; verify the specific task and jurisdiction.
What do the acronyms and key terms mean?
Expand a term before using it to make a safety or reporting decision; the same abbreviation can refer to different duties or units.
Acronyms and key terms
Term
Full wording or expansion
Meaning for this topic
RIDDOR
Reporting of Injuries, Diseases and Dangerous Occurrences Regulations
Separate GB and NI reporting regimes; only the responsible person reports when the applicable criteria are met.
HSE hierarchy
Elimination, substitution, engineering controls, administrative controls, then PPE
A source-first order for choosing workplace controls; keep higher-order measures ahead of instructions or PPE.
PPE
Personal protective equipment
Residual protection; it cannot replace a missing physical barrier.
Near miss
Event without actual injury but with credible harm potential
Still merits internal learning and sometimes meets a specified dangerous-occurrence test.
Dangerous occurrence
Specified event under the applicable RIDDOR schedule
Not every near miss is reportable.
Potential severity
Credible consequence under slightly different conditions
Record separately from actual outcome.
Critical control
Safeguard needed to prevent serious harm
Test its real performance, not only its existence.
Active monitoring
Checking risk controls before an adverse outcome
Use alongside reactive event learning.
ERICPD
Eliminate, Reduce, Isolate, Control, Personal Protective Equipment, Discipline
Compare source removal and substitution with engineered separation before work rules or PPE; Discipline means checking that stronger controls keep working.
Which documents can I download for this topic?
Download editable resources from the SHAREhub environment to support your work. Working forms and spreadsheet input areas are blank. Reports, plans, guides, briefings, procedures and policies contain completed worked example content to adapt.
Event first report and triage record
One-page initial facts, evidence, potential harm, immediate protection, national reporting owner/deadline and investigation handover record.
Blank form or working record · DOCX · 25 KB · v1.0
Wren Parcel Services report challenges falling counts when exposure halves, separates near-miss reporting changes and follows peak roll-cage overflow through a failed retest to a bounded later decision.
Save knowledge, access the full guide and receive your free monthly AI and resource allowance.
We will use your account details to provide SHARE. Marketing preferences are selected separately and can be changed at any time.
Welcome back
SHARE Paid
100 new library resources, 20 shared assessment uses, 10 policies, 20 toolbox talks and 10 audit templates each month. 300 AI questions or audit explanations per month. Each category is an account-wide total. AI questions and audit explanations share one allowance. AI risk assessment drafts, AI bowtie drafts and new completed SHAREfire reports share the assessment allowance. Policies, toolbox talks and audit templates each have their own allowance. Download your own document again without using an allowance. Previously selected library resources and alternate formats use no extra library selection. Expanded document library and 10.5% off LMS CPD courses.
£17.99 per person / month excluding VAT. VAT is added at checkout once your address is entered. 100 included e-learning courses, simulated learning environments, learning based on NEBOSH criteria, simulated workplaces and youSHARE workforce presentations. Business tools, specialist courses and qualifications are separately priced.
Reactive monitoring essentials
Practical learning for people who need to understand reactive monitoring and apply it at work.
Course dates and certificate details will be confirmed before booking.
Bring this into my business
Link my operations to SHARE guidance and AI Intelligence.
Connect workplace activity to practical topic guidance: risk registers, legal duties, controls, audits, incidents, training, competence and continuous improvement.
Demo requests can be routed to the live CRM or member account workflow when the live workflow is connected.
Ask SHARE Intelligence
This access journey shows how SHARE Intelligence will work. The live service will return permission-aware answers with supporting official sources.
Unlock another resource
You have used this month’s two free downloads. Publish a post in your own words to unlock one more resource, or choose SHARE Individual for 10 downloads per month.
You decide whether to share. If you do, use the relevant platform disclosure tools and do not make claims you do not genuinely hold.
Action recorded
This SHARE action is ready to connect to account, payment, course and document services.
Unlock another resource
You have used this month’s two free downloads. Publish a post in your own words to unlock one more resource, or choose SHARE Individual for 10 downloads per month.
You decide whether to share. If you do, use the relevant platform disclosure tools and do not make claims you do not genuinely hold.