SHARE Knowledge Hub

Human Failures, Human Factors and Human Reliability

Human failure analysis distinguishes unintentional slips, lapses and mistakes from deliberate rule deviations, then examines the job, person and organisation around the event. For the conveyor isolation and jam-clearing example, make identification and physical safeguards robust before relying on memory or retraining. Human reliability estimates need task-specific assumptions and data; a number alone cannot prove a barrier will work.

Updated 2026-11-11UK focus

Understanding Human Failures, Human Factors and Human Reliability

Human factors is the interaction of the task, equipment, environment, person and organisation that shapes health and safety performance.

Why this matters at work

Human reliability analysis (HRA) may be qualitative or quantitative. Qualitative analysis identifies tasks, error modes, PIFs and barriers. A quantitative estimate can support a high-consequence risk study, but its value depends on task definition, quality of evidence, assumptions and applicability of the selected method and data. HSE calls for a proportionate approach; a generic probability copied from another task or industry is not a site-specific fact. State whether the number represents an action failure, a whole task, or a failure to recover, and under which conditions.

When an unsafe deviation creates a near miss, analyse the hazardous mechanism and barrier failures. In a garage, bypassing a lift lock can cause crush injury; in manufacturing, defeating an interlock can lead to amputation; in a chemical plant, bypassing a trip can allow runaway or release. Preventive barriers include design and accessible safe methods; recovery includes detection of bypass status, supervisor challenge, stop-work authority and emergency response. Observation cards alone will not correct an impossible production schedule.

How organisations manage this in practice

Break the task into meaningful steps and ask what could be omitted, done late, done to the wrong object, done in the wrong direction or performed on the basis of a mistaken diagnosis. Record the cause-relevant PIFs, immediate outcome and hazard mechanism. The HSE inspectors’ toolkit provides a proforma covering step, likely failure, recovery potential, consequence, preventive measures and measures to reduce consequences. Use it as a guide, not a requirement to catalogue every minor motion. Focus effort where the failure can defeat a critical control.

A violation is a deliberate departure from a rule, but it does not automatically imply malicious intent. HSE distinguishes routine, situational and exceptional patterns. A shortcut may have become normal because supervision accepts it, a worker may improvise because tools or time are missing, or an unusual situation may prompt a well-intentioned but unsafe departure. A rule that conflicts with the physical task or with competing management instructions cannot be made reliable through punishment alone. Intent, context and actual feasibility must be established fairly.

Compare work as imagined with work as done. Observe whether the required tool, access, isolation, PPE and time are available. Ask workers what makes the procedure difficult, what they do instead and how supervisors respond. Separate a genuine workable rule deliberately ignored from a document that has not kept pace with plant change. Incentives matter: a zero-delay target may quietly reward bypassing a check. Reform the work system, make rules concise and relevant, and maintain proportionate accountability for serious intentional misconduct.

What are the key facts about human failures and reliability?

The key fact is that error is usually predictable when the task, equipment or organisation makes failure likely.

Human error is not a root cause

It is usually a starting point for deeper analysis of work design, competence, supervision, culture and controls.

Different failures need different controls

A slip, lapse, mistake and violation are not fixed by the same action.

Reliability depends on context

A person may perform reliably in normal conditions but fail during fatigue, overload, unclear displays or abnormal work.

Task analysis makes error visible

Breaking work into steps helps identify where error is credible and which controls are needed.

Good design beats repeated reminders

Engineering, layout, prompts, interlocks and simpler tasks are usually stronger than telling people to take care.

What do human failures, human factors and human reliability mean?

Human failure and fair investigation

Human failure is failure of required safe performance. An unintentional error and a deliberate departure from a rule differ: a shortcut may achieve the person’s immediate production aim while breaching the safe system. HSG48’s routine, situational and exceptional violation categories do not determine blame or a disciplinary outcome. Establish context, intent, system conditions and evidence separately.

The topic explains how people interact with work systems and how organisations can reduce predictable failure.

Human failures are not all the same. Some are unintended errors, such as selecting the wrong control, forgetting a step or misunderstanding a situation. Others are violations, where a person deliberately departs from a rule. Even violations need careful analysis because the rule may be impractical, conflicting, poorly supervised or routinely undermined by work pressure. HSE introduction to human factors

Human factors is the wider discipline that studies the job, the person and the organisation. Human reliability is the practical question: if this person is a barrier in the risk assessment, can we rely on that action under the real conditions?

ConceptPlain-English meaningWorkplace example
Human failureAn action or decision that fails to achieve what was intended.Forgetting to replace a guard after maintenance. HSE introduction to human factors
Human factorsWork design factors that influence behaviour and safety.Poor display design makes a wrong reading more likely. HSE introduction to human factors
Human reliabilityLikelihood of correct performance when needed.Operator responds to alarm in time. HSE introduction to human factors
Work as imaginedHow procedures or managers think the work is done.Checklist says two-person check is always used. HSE introduction to human factors
Work as doneHow the work is actually performed in real conditions.Second checker is unavailable during peak workload. HSE introduction to human factors

What are slips, lapses, mistakes and violations?

Classifying the failure helps choose a useful control rather than defaulting to retraining.

A slip is an action error, such as turning the wrong switch when the intention was correct. A lapse is a memory failure, such as forgetting a step. A mistake is a wrong plan or judgement, such as using the wrong method because the situation was misunderstood. A violation is a deliberate departure from a rule. HSE HSG48 full guide

Each needs a different response. Slips may need better layout, labels or interlocks. Lapses may need checklists and prompts. Mistakes may need better competence, information and decision aids. Violations may need rule review, supervision, resources, culture change or accountability, depending on why the violation occurred.

Failure typeWhat it meansBetter control
SlipRight intention, wrong action.Distinct controls, guarding, labels, physical separation and confirmation prompts. HSE HSG48 full guide
LapseMemory or attention failure.Checklists, reminders, independent checks and reduced interruption. HSE HSG48 full guide
Rule-based mistakeWrong rule applied or rule misunderstood.Better procedures, examples, supervision and competence checks. HSE HSG48 full guide
Knowledge-based mistakePerson has to solve a novel problem and chooses wrongly.Training, decision aids, escalation and expert support. HSE HSG48 full guide
ViolationDeliberate departure from a rule.Understand motive, remove pressure, fix poor rules and apply fair accountability. HSE HSG48 full guide

How does human performance affect this work?

Explore the distinction between an unintended error and a deliberate deviation, then check the conditions surrounding both. Use the examples to develop questions; the overview does not establish why a real event happened.

Select any box to open its explanation below. You can also use the grouped text headings. Several explanations can stay open for comparison.

Human-performance overview. Unintended errors branch into skill-based slips and lapses, and rule-based or knowledge-based mistakes. Deliberate deviations include routine, situational and exceptional departures. Job, individual and organisation factors influence every branch. Full explanations follow.

Original SHARElearn teaching overview. Arrows show groupings, not a causal sequence. Examples are fictional; no box establishes an actual cause, diagnosis or responsibility.

Start with the work context

Human performance in context

Human factors considers how the job, the individual and the organisation interact. A human action is a starting point for inquiry, not a complete explanation.

Fictional example: A pump control is operated incorrectly. The team examines what the operator could see, the control layout and the work arrangements.

Investigate and improve: Reconstruct the information and options available at the time. Ask what made the action understandable and what would prevent or tolerate it.

Unintended errors

An action or decision goes wrong without an intended departure from the expected method. Distinguish doing the wrong action from choosing an unsuitable plan.

Fictional example: A person intends to stop pump A but presses the adjacent control for pump B.

Investigate and improve: An outcome alone does not establish intent. Compare the person’s account, task sequence, equipment and available records; retain uncertainty.

Unintended errors: actions and decisions

Skill-based action errors

A familiar task is intended correctly but its execution goes wrong through a slip or lapse. Experienced people can be affected.

Fictional example: A routine restart is interrupted and the person resumes at the wrong point.

Investigate and improve: Examine distractions, task design and place-keeping aids. Repeating training alone does not remove the conditions that permit these errors.

Slips of action

The intended action is clear, but a different action is performed.

Fictional example: While reaching to stop a pump, a person operates a similar-looking neighbouring switch.

Investigate and improve: Check control spacing, identification, feedback, visibility and interruption. Consider clearer separation or error-tolerant design, with competent review and testing.

Lapses of memory

A needed step is forgotten or the person loses their place.

Fictional example: After an interruption, a person omits a required check while believing the sequence is complete.

Investigate and improve: Check the interruption and restart arrangements. Consider point-of-use prompts, reliable step records and proportionate independent checks for critical steps.

Mistakes in planning or judgement

The chosen action is carried out as intended, but the plan or judgement is unsuitable.

Fictional example: A person selects a familiar response to a warning, believing it fits the present conditions.

Investigate and improve: Check what was known, what the rule covered and how the situation was understood. Consider information, decision support and task-specific competence.

Rule-based mistakes

A remembered rule is misapplied, or an unsuitable rule is used. An apparently missing good rule also needs inquiry: was it known, understood and applicable?

Fictional example: A response suitable for pump A is applied to pump B even though their isolation requirements differ.

Investigate and improve: Inspect the actual procedure and its scope, access and revision. Explore interpretation. Missing a step does not by itself prove a deliberate deviation.

Knowledge-based mistakes

An unfamiliar situation is approached through reasoning without a suitable established solution; the resulting judgement is wrong.

Fictional example: An unusual pump condition is interpreted using incomplete information, leading to an inappropriate response.

Investigate and improve: Examine information gaps and available support. Improve escalation, diagnostic aids and arrangements for obtaining competent advice before uncertain work proceeds.

Deliberate deviations: understand why

Deliberate deviations / violations

A rule or procedure is knowingly departed from. The departure is intentional; harm need not be intended. Establish this distinction through evidence.

Fictional example: A required verification is knowingly bypassed to continue a task.

Investigate and improve: Ask why the rule was bypassed, whether it was workable and what the organisation encouraged or tolerated. Fair accountability and system improvements can both be needed.

Routine deviations

Departures become the usual way work is carried out.

Fictional example: A team commonly skips a required handover check and supervisors accept the practice.

Investigate and improve: Compare written arrangements with everyday work, including management knowledge and response. Make the safe method workable and verify that practice changes.

Situational deviations

A departure is associated with conditions such as time pressure, insufficient resources or unsuitable equipment. These conditions do not authorise unsafe work.

Fictional example: The correct equipment is unavailable and a deadline encourages an improvised shortcut.

Investigate and improve: Check resources, conflicting targets and whether people can stop and escalate. Remove the pressure or constraint rather than treating the shortcut as the solution.

Exceptional deviations

A departure occurs in unusual circumstances outside normal practice. This label is not an automatic justification.

Fictional example: During an unfamiliar equipment upset, a person knowingly bypasses a rule while trying to restore operation.

Investigate and improve: Reconstruct the situation and information available. Review abnormal-event preparation, support, escalation and protection; do not infer malicious intent from the outcome.

Check factors across every branch

Performance influencing factors

Conditions affecting performance can sit within the job, the individual or the organisation. Consider them across errors and deviations.

Fictional example: A difficult control layout combines with an interrupted shift and a production target.

Investigate and improve: Identify specific conditions, their evidence and how they interacted. Do not turn a list of factors into unsupported causal conclusions.

Job and task factors

Consider the work itself: equipment, interface design, instructions, workload, environment, timing and communication.

Fictional example: Two similar controls are poorly lit while alarms and interruptions compete for attention.

Investigate and improve: Observe representative work safely, compare intended and actual demands, and test feasible design changes with the people doing the task.

Individual factors

Consider relevant knowledge, experience, abilities and current needs fairly. Observed behaviour does not establish a health diagnosis or intent.

Fictional example: A newly assigned worker does not understand an unfamiliar alarm; a colleague also reports yawning after a long shift.

Investigate and improve: Check induction, understanding, shift and welfare information through appropriate private routes. Yawning alone proves neither fatigue nor the cause of an event; seek competent support when needed.

Organisational factors

Consider staffing, resources, supervision, targets, planning, culture, change management and learning from earlier events.

Fictional example: A known leak remains open because repair responsibility is unclear and closure is recorded without checking the work.

Investigate and improve: Trace decisions, ownership and earlier warnings. Improve the underlying arrangements and verify effectiveness, rather than closing the investigation at “operator error”.

Try the evidence questions

Choose one fictional pump or travel example. What is observed, what remains a hypothesis, which job or organisational factor needs checking, and what improvement would you test? Explain what evidence would change your view.

Explore at your own pace. These are optional thinking prompts: this page does not save answers, assess performance or create a learning record.

Sources and scope

Original SHARElearn overview informed by HSE guidance. The diagram groups concepts for learning; it does not model a causal sequence. Guidance checked 1 November 2026.

Continue with the incident and accident investigation course. The course outline explains its learning, optional reflections and completion requirements.

How does Rasmussen skill-rule-knowledge behaviour help learning?

The skill-rule-knowledge model helps explain why different tasks create different error risks.

Skill-, rule- and knowledge-based behaviour is a learning model, not a way to assign fault to a person. HSG48 explains slips and lapses in familiar skill-based work and rule- versus knowledge-based mistakes; match the control to the task and information available. HSE HSG48 full guide

Skill-based behaviour is fast and automatic. It helps experienced people work efficiently, but it can create slips when controls are similar or attention is interrupted. Rule-based behaviour uses known rules and procedures; it can fail when the wrong rule is selected or the rule is vague. Knowledge-based behaviour happens in unfamiliar situations and is more demanding because the person must reason from first principles.

This matters in emergencies and abnormal operations. A task that is normally skill-based can suddenly become knowledge-based when alarms, plant state and time pressure change. Training and procedures should therefore include abnormal scenarios, not only normal routines.

Behaviour levelTypical situationControl implication
Skill-basedExperienced worker performs routine action.Design controls to prevent slips and interruptions. HSE HSG48 full guide
Rule-basedWorker follows a known procedure or rule.Make rules clear, usable and tested. HSE HSG48 full guide
Knowledge-basedWorker faces an unfamiliar or complex problem.Provide decision aids, escalation routes and scenario training. HSE HSG48 full guide
Transition pointRoutine task becomes abnormal.Use triggers that tell people when to stop and escalate. HSE HSG48 full guide
Learning designTraining includes realistic conditions.Assess competence through scenarios, not just quizzes. HSE HSG48 full guide

How do job, individual and organisational factors shape performance?

Human reliability improves when the job, the person and the organisation are all considered together.

Job factors include workload, equipment, procedures, lighting, noise, workspace and task complexity. Individual factors include competence, fatigue, health, experience and risk perception. Organisational factors include staffing, leadership, culture, incentives, supervision, resources and change management. HSE introduction to human factors

A weak analysis blames the person. A stronger analysis asks what job and organisational conditions made failure more likely, and what would make success easier next time.

FactorExamplesReliability improvement
JobComplex steps, awkward access, poor labels, high noise, similar controls.Simplify task, improve layout and add prompts. HSE introduction to human factors
IndividualNew starter, fatigue, stress, unfamiliar equipment.Competence assessment, supervision and recovery time. HSE introduction to human factors
OrganisationProduction pressure, understaffing, unclear priorities, poor change control.Leadership review, resources and clear decision rights. HSE introduction to human factors
InterfacePoor display, alarm flood or confusing controls.Human-centred design and field testing. HSE introduction to human factors
CulturePeople hide errors or normalise shortcuts.Just culture, reporting and learning action. HSE introduction to human factors

How should violations be understood without excusing unsafe behaviour?

Violations need fair analysis because the same visible behaviour can have very different causes.

HSG48 separates routine, situational and exceptional violations. These are categories for understanding how a deviation arose, not automatic findings of blame; test resources, rule usability and supervision before any employment response. HSE HSG48 full guide

Routine, situational and exceptional deviations need different investigations. If evidence suggests deliberate disregard of a serious risk, investigate fairly under the appropriate employment process after testing system causes.

Good managers ask whether the rule is realistic, whether resources are adequate, whether supervisors tolerate the shortcut, whether production targets reward it, and whether workers understand why the rule matters.

TypeWhat it looks likeManagement response
Routine violationEveryone skips the same step.Investigate normal practice and redesign the task or rule. HSE HSG48 full guide
Situational violationPeople bypass rule to get work done under pressure.Review resources, timing, tools and supervision. HSE HSG48 full guide
Exceptional violationRule broken during unusual event.Check emergency guidance and escalation routes. HSE HSG48 full guide

How should just culture and accountability be balanced?

Human factors is not about excusing poor behaviour, but it is also not about lazily blaming operator error.

A just culture asks fair questions before deciding how to respond. Did the person have the right training, tools, time, information and supervision? Was the rule usable? Was the unsafe shortcut normal practice? Were targets, staffing or leadership messages pushing people toward the behaviour? These questions protect learning because they stop the organisation from closing an investigation too early. HSE managing human failures

Accountability still matters. Deliberate reckless behaviour, knowingly bypassing a critical control without reason, falsifying records or ignoring a clear life-critical rule may need formal action. The mature position is to separate human error, at-risk behaviour, system-induced violation and reckless conduct so that learning, fairness and standards can all exist together.

SituationLikely interpretationBetter management responseEvidence to consider
Slip or lapse during a well-designed taskUnintended human error.Improve prompts, layout, checks, interruption control or task design.Observation, procedure usability, labels, workload and recent interruptions. HSE managing human failures
Rule broken because the task cannot realistically be completed otherwiseSituational violation or poor rule design.Fix resources, access, timing, equipment or procedure before blaming the person.Worker interviews, supervisor knowledge, production pressure and previous workarounds. HSE managing human failures
Shortcut used because it has become normal across the teamRoutine drift and weak supervision.Reset expectations, explain risk, redesign controls and verify follow-up.Audit findings, toolbox talks, supervisor checks and trend evidence. HSE managing human failures
Person knowingly bypasses a critical control for convenienceDeliberate deviation requiring evidence-led investigation; convenience alone does not establish recklessness.Use fair investigation and accountability while checking system contributors.Training record, rule clarity, supervision, intent, consequence awareness and past behaviour. HSE managing human failures
Record falsified or hazard concealedTrust and governance failure.Escalate formally and protect evidence, while checking cultural reasons people hide bad news.Records, interviews, reporting culture, leadership messages and audit trail. HSE managing human failures

How does task analysis improve human reliability?

Task analysis breaks work into steps so credible errors and controls can be identified.

A task analysis should be done with the people who perform the work. It should include normal conditions, non-routine conditions, time pressure, tools, communication, environmental constraints, decision points and what happens if the work does not go as planned. HSE HSG48 full guide

The output should improve the job, not just produce a document. It may lead to better layout, fewer steps, clearer labelling, redesigned controls, better supervision, added checklists or removal of unnecessary decisions.

OutputWhat it tells youAction example
Task stepsWhere critical actions occur.Highlight hold points in procedure. HSE HSG48 full guide
Error modesHow a person could slip, forget, misunderstand or violate.Add prompts, interlocks or independent checks. HSE HSG48 full guide
Performance influencing factorsWhat makes success harder or easier.Improve lighting, access, staffing or time. HSE HSG48 full guide
ControlsHow the task is supported.Add engineering control before relying on memory. HSE HSG48 full guide
VerificationHow success is checked.Supervisor observation or second-person check. HSE HSG48 full guide

How do ergonomics and workplace design affect reliability?

Ergonomics makes work fit people rather than expecting people to overcome poor design.

Physical ergonomics includes reach, posture, force, visibility, manual handling and access. Cognitive ergonomics includes displays, alarms, mental workload, decision support and information design. Organisational ergonomics includes staffing, work patterns, communication and culture. HSE control rooms

In practical terms, reliability improves when controls are distinguishable, information is easy to interpret, labels are visible, tools fit the job, and the person can perform the task without awkward movement or unnecessary memory load.

Design issueError riskBetter design
Similar buttonsWrong control selected.Different shape, colour, spacing and confirmation. HSE control rooms
Poor accessWorker takes unsafe shortcut.Redesign platform, access or task sequence. HSE control rooms
Hard-to-read displayWrong value used for decision.Improve display, units, contrast and alarm limits. HSE control rooms
Heavy or awkward toolFatigue and rushed work.Tool redesign, mechanical aid or task rotation. HSE control rooms
Noisy environmentInstruction misunderstood.Radio protocol, visual confirmation and quieter briefing area. HSE control rooms

What matters in control-room design and monitoring roles?

Control rooms rely heavily on human reliability because operators must maintain situation awareness and respond correctly.

A good control room supports attention, diagnosis and action. It should not overload people with low-value alarms, scattered information, poor displays or ambiguous plant status. It should also consider staffing, fatigue, handover, abnormal scenarios, lighting, seating, noise and emergency communications. HSE control rooms

Control-room design is not only for major hazard sites. Traffic rooms, security rooms, building management systems, CCTV suites, logistics hubs and energy control points all depend on people recognising changes and responding in time.

AreaGood practiceEvidence
Alarm managementAlarms are prioritised, actionable and reviewed.Alarm dashboard and rationalisation record. HSE control rooms
Display designInformation supports diagnosis and trend recognition.Operator feedback and interface review. HSE control rooms
HandoverStructured handover covers abnormalities, isolations and inhibited systems.Handover log and readback check. HSE control rooms
FatigueShift design manages alertness and recovery.Fatigue assessment and rota review. HSE control rooms
Emergency communicationMessages are clear, tested and role-specific.Drill records and emergency plan review. HSE control rooms

How does fatigue affect human reliability?

Fatigue reduces attention, memory, reaction time, judgement and willingness to challenge unsafe conditions.

Fatigue is not just sleepiness. It can come from long hours, shift work, early starts, night work, commuting, overtime, workload, stress, illness, caring responsibilities and insufficient recovery. It can interact with other human factors such as underload, alarm monitoring, heat and safety-critical driving. HSE fatigue and shiftwork

A serious organisation designs fatigue controls into work planning. It does not wait for workers to self-declare fatigue after the job has already become unsafe.

SituationRiskControl
Night shift monitoringReduced vigilance and slower alarm response.Task rotation, breaks and alarm support. HSE fatigue and shiftwork
Overtime after shutdownErrors during isolation or reinstatement.Shift limits and high-risk task scheduling. HSE fatigue and shiftwork
Long commute before shiftReduced alertness before work begins.Rota planning and fatigue conversation. HSE fatigue and shiftwork
High workload and low restSkipped checks and poor decisions.Workload review and supervisor escalation. HSE fatigue and shiftwork
Safety-critical drivingMicrosleeps and slower reactions.Journey planning and no-drive triggers. HSE fatigue and shiftwork

How can organisations improve human reliability?

Human reliability improves when controls support people before, during and after the task.

A human reliability estimate depends on the defined task, baseline data, time pressure, display design and other performance-shaping assumptions. HSG48 warns that quantified methods are better suited to well-learned routine tasks and require care in unfamiliar conditions. Record uncertainty and never substitute a generic probability for field barrier evidence. HSE HSG48 full guide HSE managing human failures

The strongest interventions remove the error opportunity, reduce complexity, make hazards visible, support correct action and detect failure early. Training is important, but it is only one layer. Reliability also needs good design, tested procedures, competent supervision, workload control, feedback and learning.

Where human action is claimed as a barrier in a risk assessment, the organisation should be able to show why that action is dependable. What is the cue? How much time is available? What could distract the person? What if the person is new, tired or interrupted? How is the response verified?

ApproachExampleWhy it helps
Remove choiceUse keyed connections or interlocks.Prevents wrong selection. HSE HSG48 full guide
Make cues clearUse visible alarms, labels and limits.Improves recognition and response. HSE HSG48 full guide
Reduce memory dependenceUse checklists and prompts.Prevents lapses. HSE HSG48 full guide
Practice abnormal scenariosUse tabletop or simulator exercises.Improves knowledge-based performance. HSE HSG48 full guide
Verify critical actionUse second-person check or independent instrument.Detects failure before consequence. HSE HSG48 full guide
Learn from weak signalsReview near misses and workarounds.Fixes drift before incident. HSE HSG48 full guide

What does a worked human-reliability task example look like?

A task-step example shows how the theory becomes a practical control plan.

For the conveyor isolation and jam-clearing example, compare the written sequence with the real controls and line labels, then test whether a slip can be detected or physically prevented. A sign-off or refresher alone leaves the same error path open. HSE HSG48 full guide HSE procedures

Consider a maintenance task where a worker must isolate a conveyor, clear a jam, check the area and return the machine to service. The risk is not only the jam itself. The human-reliability question is whether the task gives the person clear cues, enough time, usable equipment, competent supervision and a recovery route if something is missed.

This type of analysis is useful for learners because it connects slips, lapses, mistakes, violations and performance influencing factors to real safeguards. It is also useful for supervisors because it shows what evidence should be checked before the task is treated as controlled.

Task stepPossible failurePerformance influencing factorsSafeguardsRecovery controls and evidence
Identify the blockageWorker reaches into the nip point before understanding stored energy.Noise, poor visibility, production pressure and routine jam clearing.Stop-work rule, viewing point, guarded access and supervisor briefing.Near-miss reporting and supervisor observation of jam-clearing tasks. HSE HSG48 full guide
Isolate and lock offWrong isolator selected or lock not applied.Poor labels, similar panels, time pressure and interruptions.Unique labels, isolation procedure, lock-off kit and try-start test.Isolation certificate, lock register and spot checks. HSE HSG48 full guide
Remove guard or access panelGuard removed before isolation is proven.Awkward access, weak procedure and past shortcuts.Interlocked guard, permit or task checklist, and hold point.Workface verification and photo or supervisor sign-off where proportionate. HSE HSG48 full guide
Clear the blockageTool slips, body enters danger zone or unexpected restart occurs.Manual force, fatigue, poor tool choice and limited space.Correct tools, zero-energy confirmation and controlled restart rules.Post-task debrief and defect action if jams are frequent. HSE HSG48 full guide
Reinstate and restartGuard not replaced or people remain inside the danger area.Distraction, shift change and poor communication.Final area check, two-person confirmation for high-risk tasks and restart warning.Restart checklist, guarding inspection and action close-out evidence. HSE HSG48 full guide

How does a human error finding become a better investigation?

A good investigation treats error as evidence of a system problem to understand, not the end of the analysis.

Imagine a maintenance worker removes a guard to clear a blockage and the machine is restarted before the guard is replaced. A weak report says the worker failed to follow the rule. A stronger report asks why the blockage was frequent, why isolation was not applied, why the guard design made cleaning difficult, whether supervisors knew the workaround, whether production pressure existed and whether the procedure could be followed in real conditions. HSE managing human failures

This style of analysis produces stronger actions because it changes the conditions that made the failure credible.

LayerWeak findingStronger review
PersonWorker made a mistake.Was the worker competent, fatigued, interrupted or under pressure? HSE managing human failures
TaskProcedure not followed.Was the procedure usable and was isolation practical for blockage clearing? HSE managing human failures
EquipmentGuard was removed.Could the blockage be cleared without removing the guard? HSE managing human failures
SupervisionSupervisor did not see it.Was this shortcut known, tolerated or hidden by workload? HSE managing human failures
OrganisationMore training required.Fix blockage cause, guarding, isolation method, supervision and production pressure. HSE managing human failures

What evidence shows human reliability is being managed?

Evidence should show that error traps have been identified, tasks improved and controls checked in practice.

Good evidence includes task analysis, procedure review, observations, competence assessments, design reviews, error reports, audit findings, training scenarios, workload assessments and action verification. The best evidence proves the organisation has improved the system, not merely reminded the worker. HSE managing human failures

For high-risk work, managers should be able to trace a control from risk assessment to procedure, training, supervision, monitoring and review.

EvidenceWhat it showsQuality check
Task analysisCritical steps and error modes are known.Was it done with workers? HSE managing human failures
Procedure reviewProcedure is current and usable.Was it tested at the workface? HSE managing human failures
Observed assessmentCompetence is demonstrated in realistic conditions.Does it include abnormal conditions? HSE managing human failures
Incident learningHuman factors are analysed beyond blame.Are actions systemic? HSE managing human failures
Audit findingsControls are checked and improved.Are actions verified? HSE managing human failures
Worker feedbackWorkarounds and weak signals are visible.Is feedback acted on? HSE managing human failures

How can the hierarchy of controls reduce error-likely conditions and the consequences of human failure?

ERICPD is used here as a planning mnemonic. The linked HSE five-level hierarchy is the official source for the order and relative reliability of controls; the two labels are not identical.

Start with the exposure or failure path and prefer removal or physical redesign before procedures or PPE.

ERICPD is a planning mnemonic: Isolate generally maps to engineering, Discipline sustains controls, and the five-level hierarchy names substitution separately. Each candidate requires competent task assessment. HSE five-level hierarchy HSE five-level hierarchy

How should management verify controls for this task?

For wrong-valve maintenance step, error classification and system redesign, the management check should start with a real control decision: Remove the wrong-valve choice by plant or route redesign. Name the person who will test it, keep evidence from the actual work, and reopen the assessment when the failure condition in the hierarchy table occurs. HSE management-system guidance.

A review should compare the planned control with what workers and supervisors can use in practice. Record the defect, owner, interim protection, verification and next review trigger so that a policy statement or certificate does not stand in for a working control.

What must each role demonstrate?

Record an observed task decision or simulation, the assessor and evidence, and a trigger for reassessment.

Briefing attendance alone cannot prove that a person recognises the hold or referral point. HSE HSG48 full guide

RoleDemonstrationAssessor and recordReassess when
WorkerDescribe actual task, interruption and wrong-valve traps.Assessor observes walkthrough.Task changes. HSE HSG48 full guide
SupervisorClassify error/violation only after factual investigation.HF adviser reviews case.New evidence. HSE managing human failures
DesignerRemove confusing interfaces and enable verification.User trial and peer review.Modification. HSE introduction to human factors
Risk analystDocument task and assumptions before estimating failure probability.Technical peer reviews model.Inputs or context change. HSE HSG48 full guide
ManagerVerify corrective controls rather than default retraining.Senior reviewer samples effectiveness.Repeat event. HSE managing human failures

How should this be used for NEBOSH Diploma study?

Diploma answers should apply the theory to realistic workplace decisions and evidence.

A strong answer explains slips, lapses, mistakes and violations, then links them to job, individual and organisational factors. It should show how task analysis and ergonomic design can reduce the likelihood of failure. It should avoid phrases such as 'carelessness' unless there is evidence. HSE introduction to human factors

In scenario questions, use the visible facts: time pressure, fatigue, poor lighting, missing supervision, difficult access, confusing alarms, unclear procedure, production pressure, weak training or repeated previous near misses.

QuestionGood answerWeak answer
Why did a worker bypass a guard?Discuss violation type, task design, blockage, access, supervision and culture.Worker was negligent. HSE introduction to human factors
How can slips be reduced?Use design, labelling, spacing, interlocks and prompts.Tell workers to concentrate. HSE introduction to human factors
What is SRK behaviour?Explain skill, rule and knowledge modes with examples.List the words only. HSE introduction to human factors
How does task analysis help?Breaks work into steps and identifies credible failures.It is a checklist. HSE introduction to human factors
How is reliability improved?Design for success, verify controls and learn from weak signals.More training. HSE introduction to human factors

What warning signs show human reliability is weak?

Warning signs often appear before harm: repeated workarounds, unreliable procedures, blame-heavy reports and controls that depend on memory.

Warning signs are included because failure usually appears before a serious event. Treat these points as prompts for inspection, audit, supervision and management review rather than as simple compliance statements. HSE managing human failures

Warning signHow it can cause harmAction
Same error repeatsThe task contains an uncorrected error trap.Run task analysis and redesign. HSE managing human failures
Rules regularly bypassedControls may be impractical or poorly supervised.Investigate violation type and fix conditions. HSE managing human failures
Procedures do not match workPeople improvise and critical steps are missed.Rewrite with workers and test in the field. HSE managing human failures
Actions say retrain onlySystem causes are left unchanged.Set engineering, supervision or work-design actions. HSE managing human failures
No worker involvementManagers miss work-as-done reality.Use observation and consultation. HSE managing human failures

What do the acronyms and key terms mean?

Acronyms should be understood before they are used in assessments, briefings, audits or learning answers.

Acronyms can exclude newer readers if they are not explained. This section keeps the main terms available at the end of the page so the article stays readable while still supporting learners and audit users.

AcronymMeaningPlain-English use
HFHuman factorsJob, individual and organisational factors affecting performance.
SRKSkill-rule-knowledgeRasmussen model of behaviour modes.
SCTASafety critical task analysisTask analysis for work where human performance is critical.
PIFPerformance influencing factorA condition that makes good or poor performance more likely.
DSEDisplay screen equipmentScreens and related workstations; relevant to ergonomic and control-room contexts.