SHARE Knowledge Hub
Hazard group - biological hazards
Biological hazards arise from exposure to microorganisms or biological material that can cause infection, allergy or other adverse health effects. Work involving people, animals, healthcare waste, sewage, contaminated water, food or laboratory materials may create exposure through inhalation, ingestion, damaged skin, splashes or sharps injuries. Examples include blood-borne viruses, legionella bacteria, contaminated waste and zoonotic infection. Assessment identifies the agent or material, how exposure occurs, susceptible people and the controls needed for the activity. Prevention may include avoiding contact, containment, source segregation, water-system management, hygiene and suitable protective equipment, supported by a prompt professional exposure-response route. The SHARE biological hazard group is a practical learning category; it must not be confused with the statutory classification of biological agents into Hazard Groups 1 to 4.
Understanding Hazard group - biological hazards
Biological hazards arise from exposure to microorganisms or biological material that can cause infection, allergy or other adverse health effects. Work involving people, animals, healthcare waste, sewage, contaminated water, food or laboratory materials may create exposure through inhalation, ingestion, damaged skin, splashes or sharps injuries. Examples include blood-borne viruses, legionella bacteria, contaminated waste and zoonotic infection. Assessment identifies the agent or material, how exposure occurs, susceptible people and the controls needed for the activity. Prevention may include avoiding contact, containment, source segregation, water-system management, hygiene and suitable protective equipment, supported by a prompt professional exposure-response route. The SHARE biological hazard group is a practical learning category; it must not be confused with the statutory classification of biological agents into Hazard Groups 1 to 4.
Why this matters at work
Biological agents can cause infection, allergy or toxicity. Identify the reservoir, release mechanism and route to the person: inhalation, contact with mucosa or damaged skin, ingestion or inoculation. Incidental exposure occurs through contaminated material during ordinary work; deliberate work intentionally handles or propagates agents. Exposure probability, consequences and susceptible people are context dependent and should not be inferred solely from the industry label.
Animal-related exposure requires the species, activity and route to be identified. Animal waste, birthing material, bites and vectors can create different problems. HSE's agriculture guidance describes zoonoses as diseases carried by animals that can affect humans. It stresses occupational hygiene and notes that visitors may also be exposed. A bite additionally involves physical injury, and venom or an allergic reaction may require a different mechanism description. Do not assume that every insect carries a specific pathogen or that an apparently healthy animal is free of an occupational hazard.
How organisations manage this in practice
The agent's classification does not settle how every person will be affected. The Approved List's assessment discussion recognises that susceptibility can be influenced by health conditions, medication, compromised immunity, pregnancy or breastfeeding. Task assessment must consider relevant additional risks through competent arrangements. Consultation should establish whether the controls and work design meet a person's needs. Supervisors need the practical adjustment, restrictions and review arrangements that allow them to manage work; they do not need to collect a complete clinical history in a general hazard register. Protect workers from assumptions based on age, disability, background or job title.
Move the assessment into purchasing, work design and everyday supervision. Specify what the biological barrier must achieve before buying equipment or contracting a service. A containment proposal needs a practical handling and cleaning arrangement, a waste route and maintenance ownership. The dutyholder and manager must provide resources and authority; the person doing a check may only be able to report a defect. Effective implementation connects that report to someone who can maintain a restriction or repair the system. Use worker consultation to discover whether the planned arrangements are usable during the actual task.
Operational evidence. Retain the fluid identity, applicable supplier information, quality-management results, equipment and exposure-control checks and assessed maintenance arrangement. Explain which result concerns the fluid and which concerns exposure. The selected source contains numerical management guidance, but this family chapter does not reproduce thresholds, biocide doses or a sampling schedule. Those decisions require the correct current task-specific guidance and competent interpretation, including any product or process exceptions.
What are biological hazards and what does their assessment cover?
Biological exposure can arise incidentally from work or from deliberate handling of agents. The ten teaching categories in this package are not the statutory biological agent Hazard Groups 1 to 4. Poisonous plants, insect venom and pollen can involve chemical or allergic mechanisms. Do not classify every bite or plant exposure as infection. These sources are occupational guidance, not individual clinical treatment advice. See Working with substances hazardous to health: A brief guide to COSHH and Legionnaires' disease. The control of legionella bacteria in water systems.
Start with the hazard group overview, then use the related topic links for task-specific background. A group checklist helps discovery; it does not establish that the controls at your site are effective. Read the hazard group overview.
Which hazards should the assessment consider?
Check each relevant mechanism during normal work, cleaning, maintenance, foreseeable failure and emergencies. Several entries can share a harm pathway; follow the linked explanation rather than treating each label as a separate assessment. See Working with substances hazardous to health: A brief guide to COSHH and Legionnaires' disease. The control of legionella bacteria in water systems.
Hazard or exposure and practical application — part 1 of 3
Read the complete visual as text
- Bacteria: Read the mechanism and controls: Bacteria viruses fungi and mould
- Viruses: Read the mechanism and controls: Bacteria viruses fungi and mould
- Fungi: Read the mechanism and controls: Bacteria viruses fungi and mould
- Mould: Read the mechanism and controls: Bacteria viruses fungi and mould
Hazard or exposure and practical application — part 2 of 3
Read the complete visual as text
- Contaminated water: Read the mechanism and controls: Contaminated water and legionella
- Contaminated food: Read the mechanism and controls: Contaminated food
- Bloodborne pathogens: Read the mechanism and controls: Bloodborne pathogens and needle sticks
- Needlestick injuries: Read the mechanism and controls: Bloodborne pathogens and needle sticks
Hazard or exposure and practical application — part 3 of 3
Read the complete visual as text
- Human waste: Read the mechanism and controls: Human waste and sewage
- Animal or insect bites: Read the mechanism and controls: Animals insects and zoonoses
- Zoonotic diseases: Read the mechanism and controls: Animals insects and zoonoses
- Plants poisonous plants and pollen: Read the mechanism and controls: Poisonous plants and pollen
Describe when the source is created or released and how it reaches someone. Compare normal operation with receipt, setup, blockage, breakdown, disposal and contractor access. The list below is a discovery aid: an omitted mechanism may still be important, while an irrelevant item does not require a fabricated assessment. Follow the mechanism explanation and test controls against the actual circumstances before scoring risk.
| Hazard or exposure | Read the mechanism and controls |
|---|---|
| Bacteria | Bacteria viruses fungi and mould |
| Viruses | Bacteria viruses fungi and mould |
| Fungi | Bacteria viruses fungi and mould |
| Mould | Bacteria viruses fungi and mould |
| Contaminated water | Contaminated water and legionella |
| Contaminated food | Contaminated food |
| Bloodborne pathogens | Bloodborne pathogens and needle sticks |
| Needlestick injuries | Bloodborne pathogens and needle sticks |
| Human waste | Human waste and sewage |
| Animal or insect bites | Animals insects and zoonoses |
| Zoonotic diseases | Animals insects and zoonoses |
| Plants poisonous plants and pollen | Poisonous plants and pollen |
How do biological agents enter the body and affect different people?
Biological agents can cause infection, allergy or toxicity. Identify the reservoir, release mechanism and route to the person: inhalation, contact with mucosa or damaged skin, ingestion or inoculation. Incidental exposure occurs through contaminated material during ordinary work; deliberate work intentionally handles or propagates agents. Exposure probability, consequences and susceptible people are context dependent and should not be inferred solely from the industry label. See Introduction to biological hazards at work and Bloodborne viruses (BBVs).
Identify the material or agent as far as the task requires, then distinguish inhalation, ingestion, damaged-skin or mucous-membrane contact and puncture. Relevant individual needs may alter a suitable arrangement, but workers should not have to disclose unnecessary personal detail in an ordinary risk log. An unknown agent can require holding work and obtaining competent advice. The assessment is not a diagnostic tool or a prediction that a particular person will become ill.
How should biological exposure be prevented at source?
Occupational immunisation decision
Where assessment identifies occupational exposure to agents with effective readily available vaccines, the employer should offer protective immunisation free of charge through competent occupational-health advice. Explain benefits and limits, obtain informed consent and keep appropriate confidential records. If vaccination is declined or ineffective, review other controls. This supplements source/pathway controls; it is not a compulsory programme for every office worker.
HSE: Preventing incidental exposure to infection at work · COSHH Regulations (Northern Ireland) 2003
Avoid contact where possible and design handling to contain material and minimise aerosol or splash generation. Coordinate cleaning, waste, water management and access. Vaccination, where appropriate through competent clinical arrangements, is supplementary rather than a substitute for controls. The biological agent Hazard Groups 1 to 4 are a legal classification and are not the same as the ten teaching groups. Laboratory containment decisions need current agent specific specialist advice. See Introduction to biological hazards at work and Legionnaires' disease. The control of legionella bacteria in water systems.
Source segregation, closed handling, suitable water-system design or a less contact-intensive method can reduce exposure before it reaches a worker. Hygiene, instruction and protective equipment then support the residual task. Verify the route during cleaning and disposal, when containment may be opened or damaged. A sample, vaccination or a clean-looking surface does not replace a workable control scheme; failures require a defined restriction and competent response.
When do bacteria, viruses, fungi or mould become an occupational exposure?
Work may release infectious or allergenic material from people, animals, waste or damp materials. Species, viability, concentration and route matter. Mould exposure is not automatically a communicable infection. See Introduction to biological hazards at work and Working with substances hazardous to health: A brief guide to COSHH.
A worker disturbs damp building material, handles contaminated waste or cleans a process enclosure. Aerosols, contact with damaged skin and hand-to-mouth transfer can expose different tissues; infection, irritation or sensitisation depend on the agent and route. The presence of mould or a generic biological label does not identify every organism or its risk.
Which source controls and checks change the outcome?
Remove the damp or contaminated source where feasible, prevent recurrence and use controlled containment and handling. The task owner assesses who can be exposed during removal, cleaning and disposal, including occupied areas and contractors. Suitable hygiene, waste arrangements and any selected Personal protective equipment (PPE) support source controls. Stop on unexpected contamination or an unknown high-consequence exposure and obtain competent advice; do not prescribe a diagnosis or antimicrobial treatment from a hazard list.
How should the controls be applied?
Control the contaminated source, moisture and release, use suitable containment and hygiene, and plan safe cleaning or remediation.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Do not diagnose infection or set containment level from appearance. Obtain current agent and task specific advice where uncertainty is significant.
How can a water system expose people to legionella?
Water systems can support bacteria and expose people through aerosols. Drinking contamination and aerosol exposure are different routes. Stagnation, system design and operation need competent review. See Legionnaires' disease. The control of legionella bacteria in water systems and Introduction to biological hazards at work.
A poorly managed water system can allow legionella to multiply, with aerosols exposing occupants or maintenance staff. Stagnation, system changes and ineffective control can matter even where water looks clear. A cleaning contractor opening or maintaining equipment can face a different exposure from the normal user.
Which source controls and checks change the outcome?
Design and operate the system to avoid conditions that favour growth and control aerosol exposure, using the competent water-risk assessment. The responsible manager assigns a suitable control scheme, checks and corrective action rather than relying on one test result. Review modifications and prolonged non-use before return to service. Stop or restrict affected use when required controls or evidence are absent; flushing, treatment and reopening decisions must come from the competent scheme, not an invented generic schedule.
How should the controls be applied?
Identify responsible water system management, assess sources and implement a suitable control scheme with monitoring and maintenance.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Record system changes and control failures. A water sample alone is not proof that the whole system is controlled.
How can food handling spread contamination to workers and customers?
Handling contaminated ingredients and failures in hygiene can expose workers and consumers. Occupational agent control and food safety responsibilities overlap but are not identical. See Running a food business and Introduction to biological hazards at work.
Raw material, unclean equipment or poor separation can transfer contamination during preparation, packing or service. Food workers may be exposed through contact while customers ingest contaminated food. A clean-looking surface or a completed temperature field does not establish that the whole handling chain is controlled.
Which source controls and checks change the outcome?
Avoid cross-contamination through process layout, suitable separation and competent food-safety arrangements. Managers verify receipt, storage, preparation, cleaning and release requirements for the food operation, using the applicable official food guidance. Staff need task instruction and a route for reporting illness or hygiene failures without blame. Hold affected product or work when identity, storage control or cleaning is uncertain; do not invent a safe cooking or storage value for an unspecified product.
How should the controls be applied?
Separate contamination pathways, use suitable hygiene and handling arrangements and follow the relevant official food business guidance.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Verify actual cleaning storage and handling; obtain organism and food process specific guidance where needed.
How can bloodborne infection follow a sharps injury?
After a sharps exposure: act urgently
Encourage the wound to bleed gently under running water; wash with running water and plenty of soap. Do not scrub or suck it. Dry and cover it, report the incident and obtain urgent medical assessment through the established service or out-of-hours route. Do not delay care for paperwork, source testing or symptoms. Clinicians decide prophylaxis and follow-up.
A contaminated needle or sharp can inoculate material; blood can also contact eyes, mucosa or damaged skin. Hidden sharps may expose cleaners and waste handlers, not only clinical staff. See Bloodborne viruses (BBVs).
A healthcare worker, cleaner or waste collector can be punctured by a discarded contaminated sharp, including through a bag. Blood or body fluid can also contact damaged skin or a mucous membrane. Appearance cannot establish whether an item carries an infection, and an absence of immediate symptoms does not resolve the exposure.
Which source controls and checks change the outcome?
Prevent sharps entering general waste; where a sharp is necessary, assess safer equipment and suitable disposal at the point of use. The manager verifies containers, collection interfaces and prompt access to a competent exposure-response service. Staff must not hand-search bags or handle an unexpected sharp beyond their training. Gloves and vaccination do not remove the need for source controls. Report and obtain prompt professional assessment after relevant exposure, with confidential incident records.
How should the controls be applied?
Avoid unnecessary sharps, use safer handling and suitable disposal at the point of use, and maintain a prompt exposure reporting and clinical response route.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Do not handle hidden sharps blindly or use general guidance to decide personal post-exposure treatment. Record the event confidentially and seek timely clinical assessment.
How can sewage work expose staff to infection?
Handling sewage or contaminated waste can create ingestion, splash and aerosol exposure. Cleaning methods and hygiene barriers determine who is affected. Enclosed drainage work adds atmospheric dangers. See Working with sewage: The health hazards - A guide for employers and Introduction to biological hazards at work.
A drain cleaner, wastewater operator or flood-recovery contractor can contact sewage through splashes, aerosols, cuts or contaminated hands. Work may also introduce gas, confined-space and drowning hazards that are not infection routes. Eating or touching the face with contaminated hands creates an avoidable pathway outside the main operation.
Which source controls and checks change the outcome?
Avoid entry and direct contact through remote methods where possible; contain splashes and provide suitable equipment, washing and clean areas. Supervisors check damaged skin precautions, task hygiene, waste handling and emergency interfaces against the assessment. Selected protective equipment must suit the combined exposure without replacing the access or isolation plan. Stop on unexpected contamination, gas concerns or failed containment; symptoms or exposure requiring clinical judgement go through the competent professional route.
How should the controls be applied?
Use containment, appropriate work methods and washing facilities; separate eating and drinking from contamination and plan competent waste handling.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Check hygiene availability in remote work and assess confined space risks separately. Avoid assuming that disinfectant removes every hazard.
How can animal contact or an insect bite transmit disease?
Animal handling, excreta, birthing material and vectors can introduce agents. Bites can also cause physical trauma or venom exposure independent of infection. See Zoonoses and Introduction to biological hazards at work.
Farm, veterinary, forestry or waste staff may handle animals, contaminated bedding or sites with biting insects. Infection can follow a bite, damaged-skin contact, inhalation or another agent-specific route. Handling a distressed animal can add crushing or kicking injury, so biological and mechanical controls may be needed together.
Which source controls and checks change the outcome?
Reduce unnecessary contact, select handling methods and design separation, hygiene and containment around the actual animals or exposure. The responsible manager obtains competent animal- and agent-specific advice and verifies staff can use the arrangements safely. Include cleaning, carcass or waste handling and seasonal changes. Stop an uncontrolled animal-handling task or unexpected exposure; gloves, repellents or vaccination where appropriate are residual measures, not evidence that every zoonotic risk is removed.
How should the controls be applied?
Plan controlled animal contact, contain contaminated material and use suitable hygiene and task specific veterinary or occupational advice.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Identify the species activity and location. An animal associated disease label does not establish the probability or treatment for an individual exposure.
How can plants and pollen cause poisoning, irritation or sensitisation?
Plant contact and airborne pollen can produce toxic or allergic effects. These mechanisms do not automatically mean an infectious biological agent is present. See Working with substances hazardous to health: A brief guide to COSHH and Introduction to biological hazards at work.
A grounds worker strims vegetation, handles an unfamiliar plant or disturbs accumulated pollen. Contact, inhalation or ingestion can cause agent-specific harm; mechanical cutting can increase airborne material or splashing sap. A person with symptoms is not a hazard, and a plant label alone does not establish the exposure.
Which source controls and checks change the outcome?
Identify the material and avoid disturbing it where possible; choose a less dispersive method and separate other people from the affected area. The task manager obtains competent identification and assessment rather than guessing from a photograph. Check clothing, tools, cleaning and waste routes for transfer beyond the job. Select suitable residual protection and reporting arrangements; stop when identification or control is uncertain and obtain appropriate advice for exposure or symptoms.
How should the controls be applied?
Identify the material and avoid or reduce contact and aerosol release. Use suitable handling and exposure controls with competent advice for sensitisation risks.
When should work stop or be escalated?
Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Retrieve chemical or allergy relevant guidance alongside this group. Do not classify every rash or bite as an infection.
How should this hazard group be assessed and managed in practice?
For drainage maintenance or cleaning work, identify contact with waste, aerosols, blood and contaminated water. Consider cleaners, contractors, visitors and workers whose health increases susceptibility. Avoid exposure and use appropriate containment, hygiene, safe waste and sharps handling, maintained water systems and competent incident response. Consult appropriate occupational health advice for vaccination and post exposure needs. Biological exposure assessment; water control scheme; hygiene facilities checks; waste handling procedures; sharps arrangements; training and exposure incident records with confidentiality protected. Follow the assessment through procurement, implementation, briefing, supervision and verification rather than stopping at a document. See Working with substances hazardous to health: A brief guide to COSHH and Legionnaires' disease. The control of legionella bacteria in water systems.
Agree the activity, affected people and prerequisites with operations, workers and any contractor before work. Test whether the task can be removed or redesigned, then verify selected controls in the place they will operate. During work, the supervisor compares conditions with the assessed method and has authority to stop. Completion includes safe waste or equipment handling, outstanding defects and a named hand-back decision; a completed risk form is not the end of the control process.
What must be established before assigning a risk score?
Identify the actual activity, foreseeable harm, people exposed and controls already demonstrated to work. Consider start up, normal operation, cleaning, maintenance, breakdown, emergency response and simultaneous work. A numerical matrix may support prioritisation but cannot establish compliance or replace a specialist assessment. Do not assign a residual risk score merely because a proposed control has been written into a form. Keep unknowns explicit and obtain site evidence before deciding that work can proceed. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Write a short causal description: the work creates or releases something, a person is exposed by a particular route, and a specified injury or ill-health outcome is foreseeable. Establish whether existing measures work in the actual task before estimating likelihood. An unknown material, unverified safe state or absent critical control is a decision gap, not a reason to select a reassuring number. The responsible manager records what must be resolved and who can authorise the next step.
Who owns each control and how should it be verified?
The dutyholder provides resources and arrangements. The operational manager assigns each control to someone able to implement it. Supervisors verify the controls at the point of work and respond to defects. Workers and representatives explain work as done and report problems. Specialist advisers address limits of local competence. Record the control, responsible role, evidence, check method, due date and escalation route. Completion of a training course or signature alone does not demonstrate effective risk control. See Managing for health and safety (HSG65).
Separate the person who funds and owns the control from the person who performs its check. For an engineered measure, record the accepted performance or condition, who verifies it, what a failed result means and how maintenance is coordinated. For a staffing or organisational measure, check actual cover, authority and staff experience. A signature confirms a recorded action, not effectiveness. The supervisor must be able to hold work and obtain a competent remedy when the required condition is not met.
Who might be affected, including people outside the work team?
Include employees, agency workers, apprentices, contractors, cleaners, maintainers, delivery drivers, service users, visitors and nearby public. Consider inexperience, pregnancy, disability, health conditions, language needs and lone work individually and without stereotyping. Consultation should identify barriers to controls rather than collect unnecessary medical details. Share relevant interface information between employers. A single activity may require several hazard groups; avoid splitting the assessment so that interacting controls have no clear owner. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Walk through the job from the perspective of someone who has not received the operator briefing: a cleaner, visiting driver, contractor, new starter or occupant of an adjoining area. Ask whether a control protects them during arrival, normal work, waste removal and emergencies. Agree who controls each shared boundary and how changes are communicated. Individual needs influence a suitable arrangement but do not justify treating an employee, disability or health condition as the hazard.
When should the assessment be reviewed and what evidence matters?
Reassess when equipment, materials, staffing, layout, working hours or environmental conditions change; after incidents, near misses, complaints, symptoms or evidence of failed controls; and through planned risk based review. Verify improvements under realistic demand, not only during an announced inspection. Retain dated observations, measurements where relevant, maintenance records and action closure evidence. No single review interval suits every risk. Health surveillance, exposure monitoring and clinical diagnosis are different activities and require their own competent arrangements. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Use a change or failure to test the original assumptions, not merely change the date on the form. A different product, higher throughput, altered route, new shift or contractor may change the harm pathway. Keep observations, applicable measurements, defects and authorisation evidence linked to the task. After correction, verify under representative demand and with affected workers. Repeated workarounds or symptoms require investigation of the design and organisation, even when no injury has been recorded.
How could biological hazards arise in construction and civil engineering?
In construction and civil engineering, refurbishment disturbs damp mould affected material. Control moisture and plan contained remediation. Task assessment and containment checks. This is an illustrative application, not a documented case or a complete method statement. See Introduction to biological hazards at work and Working with substances hazardous to health: A brief guide to COSHH.
Sequence the job with adjacent trades, delivery routes and the changing work area; the contractor supervisor must check the actual stage before releasing work. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could biological hazards arise in manufacturing and engineering?
In manufacturing and engineering, food processing maintenance opens contaminated equipment. Plan hygienic isolation and cleaning without aerosol spread. Cleaning validation and maintenance controls. This is an illustrative application, not a documented case or a complete method statement. See Running a food business and Introduction to biological hazards at work.
Include startup, product change, cleaning and maintenance as well as the normal cycle; the production supervisor and maintainer agree who can stop and hand back the equipment. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could biological hazards arise in warehousing and logistics?
In warehousing and logistics, warehouse waste handling encounters discarded sharps. Use suitable collection methods and containers. Sharps reporting and disposal arrangements. This is an illustrative application, not a documented case or a complete method statement. See Bloodborne viruses (BBVs).
Assess peak demand, vehicles, loads and visiting drivers together; the shift manager verifies separation and handling arrangements before releasing the route. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could biological hazards arise in agriculture and forestry?
In agriculture and forestry, livestock workers handle animal waste and birthing material. Prevent ingestion and contact through planned handling and hygiene. Task hygiene and veterinary advice records. This is an illustrative application, not a documented case or a complete method statement. See Zoonoses.
Consider seasonal work, lone locations, animals, terrain and access to help; the task manager verifies the method and communication before the crew starts. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could biological hazards arise in hospitality and food production?
In hospitality and food production, catering staff handle raw ingredients. Prevent cross contamination through official food safety arrangements. Storage and hygiene records. This is an illustrative application, not a documented case or a complete method statement. See Running a food business.
Check food operations, cleaning, public access and busy service periods together; the kitchen or service supervisor must be able to interrupt the task without leaving another exposure uncontrolled. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could biological hazards arise in retail and public services?
In retail and public services, public services clear litter with concealed needles. Avoid hand searching and define an exposure response. Equipment suitability and incident route. This is an illustrative application, not a documented case or a complete method statement. See Bloodborne viruses (BBVs).
Include customers, visitors and staff who arrive without the task briefing; the premises manager verifies access and a safe service alternative before the activity starts. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could biological hazards arise in offices and professional services?
In offices and professional services, office water systems restart after low occupancy. Review stagnation and the water control scheme. Competent system assessment and monitoring. This is an illustrative application, not a documented case or a complete method statement. See Legionnaires' disease. The control of legionella bacteria in water systems.
Include contractors, hybrid working and occupied-space interfaces; the facilities or team manager checks the actual setup and how problems are reported. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could biological hazards arise in education and laboratories?
In education and laboratories, laboratories deliberately handle biological agents. Use agent appropriate containment and competent oversight. Agent classification and authorised procedures. This is an illustrative application, not a documented case or a complete method statement. See Introduction to biological hazards at work.
Separate learner awareness from authorised operation and specialist intervention; the responsible teacher, technician or laboratory manager checks material identity and supervision. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could biological hazards arise in utilities and waste management?
In utilities and waste management, wastewater teams repair contaminated pumps. Control aerosol splash and hygiene and avoid confined entry. Task assessment and washing facilities checks. This is an illustrative application, not a documented case or a complete method statement. See Working with sewage: The health hazards - A guide for employers and Safe work in confined spaces.
Plan for unknown material, remote access and interfaces with the public or other operators; the supervisor holds the job until necessary identification and control evidence is available. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could biological hazards arise in energy and process industries?
In energy and process industries, industrial cooling systems produce water aerosols. Manage water system controls and change. Control scheme and monitoring records. This is an illustrative application, not a documented case or a complete method statement. See Legionnaires' disease. The control of legionella bacteria in water systems.
Manage plant state, material change, connected systems and maintenance through competent process arrangements; the shift authority checks prerequisites and controls hand-back. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How could biological hazards arise in events and transport operations?
In events and transport operations, festival crews service temporary toilets. Plan contained waste transfer and hygiene. Waste handling and welfare checks. This is an illustrative application, not a documented case or a complete method statement. See Working with sewage: The health hazards - A guide for employers.
Consider temporary equipment, weather, crowds, routes and limited setup time; the coordinator verifies the current layout and a workable stop or closure route. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.
How do you put the controls into practice?
Move from recognising harm to deciding, implementing, checking and improving the controls. Give each critical control an owner, a check method and a clear escalation route. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
- Understand the taskObserve people, equipment, materials and interfaces.
- Describe the harmIdentify exposure, energy release and foreseeable failure.
- Control at sourceAvoid, redesign, substitute, contain or separate the hazard.
- Check in real workVerify performance, defects, ownership and change triggers.
| Stage | Action | Who acts | Evidence to retain |
|---|---|---|---|
| Before work | Confirm the actual task, people, equipment, substances, location and abnormal conditions. | Operational manager with competent advice | Assessment, observations, consultation and required specialist checks |
| Control delivery | Avoid exposure and use appropriate containment, hygiene, safe waste and sharps handling, maintained water systems and competent incident response. Consult appropriate occupational health advice for vaccination and post exposure needs. | Responsible manager and authorised implementers | Biological exposure assessment; water control scheme; hygiene facilities checks; waste handling procedures; sharps arrangements; training and exposure incident records with confidentiality protected. |
| During work | Supervise the real activity; check that critical controls remain effective and workers can report problems. | Supervisor and workers | Checks, defects, changes and escalations |
| Stop and restart | Stop the affected activity when serious danger or a failed critical control is suspected. Restart only through the competent site authorisation arrangements. | Supervisor and authorised competent person | Reason for stopping, corrective action, verification and restart authority |
| Review | Revisit controls after change, incidents, near misses, symptoms or repeated defects. Check effectiveness rather than counting completed forms. | Manager, Occupational safety and health (OSH) adviser and worker representatives | Dated review, closure evidence and lessons for design and procurement |
How does ERICPD apply to biological hazards?
ERICPD stands for Eliminate, Reduce, Isolate, Control, PPE and Discipline. For biological hazards, start by removing the hazardous task or source where practicable, then reduce and separate the remaining exposure. Combine suitable safeguards and work arrangements, use relevant personal protective equipment for residual risks, and keep all selected measures effective in everyday work. See HSE: Managing risk using PPE and Managing for health and safety (HSG65).
- 1 · E Eliminate
Remove the hazardous task or source where practicable; confirm that the alternative still fulfils the task and assess remaining hazards.
- 2 · R Reduce
Use a suitable less hazardous material, process or equipment, or reduce the hazard at source. Check any new risks introduced.
- 3 · I Isolate
Separate people from the hazard through suitable containment, guarding, barriers or other task-specific separation.
- 4 · C Control
Put remaining safeguards and workable task arrangements in place. Engineering controls and administrative arrangements have different strengths.
- 5 · P PPE
Select personal protective equipment for relevant residual exposure. Check suitability, fit, compatibility, use and maintenance.
- 6 · D Discipline
Sustain the controls through management support, supervision, maintenance and learning. Resolve workarounds and failures without blaming workers.
Eliminate, Reduce and Isolate focus attention on the hazard and the exposure pathway before reliance on behaviour or PPE. Controls usually work together: an enclosure may still need safe access, maintenance and instruction. Record the reasons for choosing or rejecting stronger options and check the complete task, including cleaning, maintenance and foreseeable changes.
ERICPD is a practical learning mnemonic. The five-level hierarchy is elimination, substitution, engineering controls, administrative controls and PPE. Reduce may include substitution or source reduction; Isolate commonly involves engineering. Control can include engineering and administrative measures. Discipline supports every selected level and is not an additional protective barrier. These frameworks are related; their labels do not form identical statutory ladders.
What does each role need to know and demonstrate?
People need learning and demonstrated competence for the decisions they actually make, not the same course at every organisational level. See Working with substances hazardous to health: A brief guide to COSHH and Legionnaires' disease. The control of legionella bacteria in water systems.
For biological hazards, frontline learning must enable staff to use containment, hygiene and the exposure-reporting route. Supervisors need to check waste, water-system or animal-contact interfaces. Design, procurement and specialist assessment require deeper competence in agent-specific containment and competent exposure response. Awareness, supervised practice, assessment and authorisation are different stages; an attendance record alone does not establish competence or permit specialist intervention.
Assess practical understanding with the actual task and credible abnormal conditions. The assessor must be competent for the scope being tested; authorisation should state its boundaries. Reassess after a material change, a defect, a demonstrated gap or work outside that scope rather than assuming one fixed refresher interval suits every role.
| Role | Learning and decisions | Assessment, evidence and reassessment |
|---|---|---|
| Nearby staff and new starters | Recognise the relevant exposure, usable routes, warning signs and reporting or emergency arrangements. | Supervisor checks a practical explanation and scenario response; retain briefing scope and gaps. Repeat when routes or conditions change. |
| Frontline users | Demonstrate how to use containment, hygiene and the exposure-reporting route, including the checks, limits and stop decision. | Competent task assessor observes representative practice and a defect scenario; record task, equipment/material scope and authorisation. Reassess for changed methods or performance gaps. |
| Specialist workers and maintainers | Demonstrate the applicable technical method, safe state, interface controls and hand-back; do not infer specialist skill from general awareness. | Competent specialist assesses work within a defined scope; retain method, assessment and authorisation evidence. New equipment, material or fault type may need a new decision. |
| Supervisors and coordinators | Demonstrate how to check waste, water-system or animal-contact interfaces, manage a changed condition and hold or release work. | Manager or competent reviewer tests a realistic planning and stop/restart scenario; retain observed decisions and corrective actions. Review following interface failures. |
| Managers, purchasers and designers | Make and resource decisions on agent-specific containment and competent exposure response, including the stronger-control options and residual risks. | Competent review of specifications, trials, procurement acceptance and effectiveness evidence; record decision owner and outstanding actions. Reassess after process or organisational change. |
| OSH advisers, technical specialists and auditors | Distinguish jurisdiction and source limits, test representative evidence and recognise the boundary of their competence. | Appropriately competent review of the actual assessment, sources, sampling and closed actions; retain scope and limitations. Escalate missing technical information rather than inventing a conclusion. |
How can the hierarchy of controls reduce exposure to biological hazards?
A cleaning team collects waste from premises where contaminated sharps may be used. A misplaced sharp can puncture skin and create an infection exposure; other contaminated material can also spread through hand contact or splashes.
Illustrative SHARE example: assess stronger options first, then combine the measures needed for the remaining task. If elimination removes the task entirely, later measures address only remaining or different hazards. Each stage below explains what changes, how harm is reduced and who verifies it.
Applying ERICPD to other hazards in this group
For sewage, animal contact and contaminated water, identify the agent and route before choosing controls. Remote handling, containment, hygiene and agent-specific professional advice may be relevant. Vaccination, where appropriate, complements prevention and does not remove exposure.
Keep an assessment record of the chosen controls, reasons for the selection, action owner, verification evidence and failure response. A failed critical control requires the affected activity to be held and corrected through the competent site arrangements; PPE or a completed form does not override that decision.
Guidance supporting these teaching examples
How should a water-system change be handed back safely?
Manage this activity by preventing exposure at source, coordinating the affected people and verifying the planned controls before release. A facilities contractor modifies a building water system after a period of reduced use. Maintenance staff and later occupants can face different exposure points, including aerosol-producing use. Clear water and an apparently completed installation do not establish that the control scheme remains suitable. See Legionnaires' disease. The control of legionella bacteria in water systems and Introduction to biological hazards at work.
Illustrative SHARE workplace example
What must be agreed before work starts?
The facilities manager involves the competent water-risk assessor before alteration and reviews how the change affects stagnation, control measures, monitoring and maintenance. Avoid unnecessary dead ends or exposure through suitable design. The contractor works to the competent scheme and protects occupants from affected activities. Unknown system configuration or unavailable control evidence is a hold point.
What changes, stops or hand-back decisions matter?
Before reopening, the competent responsible people establish that the system and relevant controls are in the required condition, with the checks and any treatment determined by the scheme rather than a generic timetable. The manager records configuration, responsibilities, outstanding actions and authorised use. Subsequent checks test continuing control; a single result is not a permanent certificate of safety. Do not confuse this occupational control example with diagnosis or medical treatment.
How should jurisdiction, local rules and management assurance be handled?
Northern Ireland biological-exposure route
For Northern Ireland, assess the work under the separate COSHH Regulations (NI) 2003 and use HSENI’s topic and incident-reporting routes. Check any task-specific sharps or notification requirements for that setting; a GB guidance citation is not the NI statutory instrument.
Apply the law and regulator guidance for the work location, then use competent task and equipment information to establish the practical arrangements. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
Health and Safety Executive (HSE) guidance generally addresses Great Britain; Northern Ireland has its own instruments and Health and Safety Executive for Northern Ireland (HSENI) route. Construction, dangerous substances, equipment and other specialist topics need the applicable instrument, not a Great Britain (GB) duty copied into a Northern Ireland (NI) answer. Fire arrangements also differ across the United Kingdom (UK) nations. Foreign project examples require destination-specific official advice and competent local assessment.
Distinguish a legal duty, regulator guidance, an organisation's rule and an illustrative SHARE method. A management system can link assessment, procurement, competence, maintenance, consultation and corrective action; a certification label or an unverified standard clause does not authorise work. For this group, sample evidence on agent-specific containment and competent exposure response and compare the recorded method with the activity observed on site. Resolve conflicts or missing technical information with the responsible competent person.
How would collecting mixed waste from occupied premises work in practice?
Waste workers may encounter contaminated material or an unexpected sharp while removing bags from a service area. Infection can follow contact with damaged skin, a puncture or another relevant exposure route. The facilities manager first reduces the chance of sharps entering the ordinary waste stream through suitable source segregation and collection arrangements. See Introduction to biological hazards at work and Bloodborne viruses (BBVs).
Illustrative SHARE workplace example
What is required before and during the activity?
Before collection, agree containers, handling equipment, hygiene facilities and a competent exposure response route. Workers need to recognise suspect waste without opening bags or manually searching them. During collection, stop handling the affected item when a protruding sharp, damaged container or unexpected contamination is found; secure the area and obtain competent help through the site arrangements.
What does safe completion and hand-back require?
Complete collection only through the assessed route and record defects without including unnecessary personal health details. A puncture or exposure requires prompt professional assessment through the agreed response system, not advice from a general risk checklist. Healthcare, agriculture and wastewater work have different materials and containment needs.
Acronyms and terms
These terms distinguish the source of harm, the exposure route and the controls needed for the actual work.
| Letters or term | Expansion or definition | Meaning in this topic |
|---|---|---|
| UK | United Kingdom | A geographical description, not one identical set of health-and-safety instruments. |
| GB | Great Britain | England, Scotland and Wales; HSE guidance is generally framed for this jurisdiction. |
| NI | Northern Ireland | A separate health-and-safety legal route overseen by HSENI. |
| HSE | Health and Safety Executive | The GB regulator and a publisher of official workplace guidance. |
| HSENI | Health and Safety Executive for Northern Ireland | The NI regulator; check its applicable requirements and advice. |
| OSH | Occupational safety and health | Preventing work-related injury and ill health. |
| PPE | Personal protective equipment | Equipment worn for remaining exposure; it does not replace stronger source controls. |
| COSHH | Control of Substances Hazardous to Health | The GB hazardous-substance assessment and exposure-control route. |
| ERICPD | Eliminate, Reduce, Isolate, Control, PPE, Discipline | A learning mnemonic for selecting and sustaining controls; not a statutory ladder. |
| Hazard | A source or condition with potential for harm | Describe what creates harm, rather than calling a person the hazard. |
| Exposure | A route or contact connecting source and person | Consider dose, duration and circumstances where relevant. |
| Critical control | A measure essential to the safe arrangement | Define its required condition, check, owner and failure response. |
| Hand-back | Controlled return to operation or use | Confirm people, equipment, protection and outstanding conditions before release. |
Example handy documents
Useful records connect the actual task to control ownership, checks, stop decisions and verified hand-back. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).
The following are examples of documents an organisation could create or adapt, not downloadable files or a complete safe system. Use the task-specific information and competent review before applying them. Keep private health information outside general operational records.
What should a task and harm-route assessment contain?
Record people, source, exposure or energy, foreseeable harm, existing controls, stronger options, residual uncertainty and the responsible decision owner.
What should a critical-control check and defect log contain?
Record the required condition, check method, responsible person, failed result, restricted work and verified corrective action.
What should a change and hand-back record contain?
Capture changed material, equipment, staffing, layout or conditions; prerequisites, hold decisions, competent verification and restart authority.
What should a competence and authorisation record contain?
Name the assessed task and scope, practical evidence, assessor, limits, supervision and reassessment triggers.
What should an operational learning review contain?
Link observations, complaints, near misses or relevant exposure evidence to a design or organisational change and an effectiveness check.