Skip to topic content

SHARE Knowledge Hub

Vibration at Work

Hand-arm vibration (HAV) reaches the hands through powered tools or workpieces; whole-body vibration (WBV) reaches a seated or standing person through a vehicle or platform. Repeated exposure can damage hand nerves and circulation or contribute to back pain, while shocks and posture add to vehicle risk. Assess each worker’s real daily exposure, reduce it at source and act promptly on symptoms, defects or a likely limit-value exceedance.

Updated 2026-10-22GB and NI

Understanding Vibration at Work

Hand-arm vibration (HAV) reaches the hands through powered tools or workpieces; whole-body vibration (WBV) reaches a seated or standing person through a vehicle or platform. Repeated exposure can damage hand nerves and circulation or contribute to back pain, while shocks and posture add to vehicle risk. Assess each worker’s real daily exposure, reduce it at source and act promptly on symptoms, defects or a likely limit-value exceedance.

Why this matters at work

Use credible vibration magnitude and actual exposure time to estimate daily exposure, combining relevant tasks correctly for the individual. Keep uncertainty visible and reduce exposure when the estimate is close to a decision threshold. If a limit has been exceeded, act immediately to reduce exposure below it, establish the reasons and prevent recurrence. Do not use expired transitional provisions or an informal weekly average to justify routine exceedance. Confirm NI requirements separately and seek competent support where exposure pattern or measurement interpretation is uncertain.

Whole-body vibration and shocks are associated with back pain among drivers of mobile machines and work vehicles, especially on rough ground. Risk is influenced by magnitude, duration, repeated jolts, posture, seat adjustment, vehicle condition, speed and task. Heavy lifting, climbing, prolonged sitting, twisting to view attachments and previous back problems can contribute. Assessment should therefore address the complete driving and material-handling job rather than treating a seat measurement as the whole cause.

How organisations manage this in practice

Assurance combines assessment quality, engineering progress, field practice and health outcomes. Leading indicators include task inventory coverage, percentage of high-risk work eliminated, verified low-vibration procurement, maintenance, route repairs, supervisor observations, surveillance enrolment and closure of OH-driven control reviews. Lagging indicators include ELV exceedances, symptom referrals, diagnoses, abnormal vibration defects and severe jolts. Preventive checks and repairs measure activity; defects, shocks and exceedances found by those checks measure failed-control outcomes. Pair both, and distinguish a surveillance referral from a confirmed diagnosis. Improved reporting can increase recorded signals while prevention improves.

Do not rely on gloves to make a hazardous vibration exposure acceptable. Their performance depends on the frequencies and conditions, and they may offer little useful reduction at relevant tool frequencies. Gloves can keep hands warm and protect against other hazards, but selection must also consider grip, dexterity and compatibility. Start by avoiding the operation or using another method; then select suitable equipment, consumables and supports that reduce vibration at the source. Maintain equipment, train workers in appropriate use without excessive grip or force and plan exposure intelligently. Check that a proposed replacement actually performs the task efficiently; a lower emission figure with a much longer operating time may not reduce daily dose. Consult operators during trials and record the task conditions, exposure assumptions and results. Use health surveillance where indicated and act on symptoms independently of PPE provision. If exposure remains uncertain or potentially excessive, obtain competent assessment rather than assigning an unsupported reduction factor for a glove.

Electronic systems may log tool use, assign magnitude, calculate points and alert workers or supervisors. They can reveal variable exposure and support sharing across teams. They do not inherently reduce vibration and can mislead if a tool tag uses the wrong magnitude, the device records run time rather than contact, or workers swap equipment. HSE reports that systems can produce different outcomes for the same task, so validate performance against known exposure patterns.

Pneumatic breaking: vibration, stored air and the people nearby: illustrative 3D equipment and the people who may be affected
Interactive 3D explainerSHAREsim

Pneumatic breaking: vibration, stored air and the people nearby

Explore how this equipment can harm its users and other people, then follow the practical measures that interrupt each pathway. This is a hazards and good-practice lesson; the separate checklist remains the pre-use/safety-check activity.

Hazards and good practice: learn what can hurt people during use, change and maintenance. Pre-use and safety checks stay in the separate checklist.

Checksheets and risk assessments

Equipment checksheets

Risk assessment forms

Risk assessment examples

Forms and tools

Full written walkthrough — all 8 steps
  1. 1. Remove or redesign the breaking task

    What is happening: The breaker, hose and compressor form one work system; the tool is shown stationary.

    How harm can occur: Breaking can expose the operator to vibration, flying material, dust and high effort.

    Best practice to apply: Consider design changes, prefabrication or a suitable mechanised/remote method before selecting a hand-held tool.

    Why this works: Removing hand-held breaking can prevent transmission through the hands instead of only rationing exposure.

    Vibration at Work · What is hand-arm vibration and whole-body vibration?
  2. 2. Trace vibration into the hands

    What is happening: The handle is the interface where mechanical vibration reaches the user during contact.

    How harm can occur: Repeated exposure can damage blood vessels, nerves, muscles and joints; early symptoms may be overlooked.

    Best practice to apply: Select a suitable productive lower-vibration method and tool, then assess the actual hand-contact exposure.

    Why this works: Lower transmission and shorter productive contact reduce the exposure pathway; the animation is not a vibration measurement.

    Vibration at Work · How can hand-arm vibration affect blood flow, sensation and everyday hand function?
  3. 3. Understand trigger time and the full day

    What is happening: Actual contact with a vibrating tool differs from the length of the booking or shift.

    How harm can occur: Under-counted bursts and other tools can leave cumulative exposure unmanaged.

    Best practice to apply: Observe representative work, include every relevant tool and task, and use suitable data and work-pattern information.

    Why this works: A whole-day picture prevents a short-looking individual job concealing a larger combined exposure.

    Vibration at Work · How do HAV trigger time and points work?
  4. 4. Keep the tool working efficiently

    What is happening: Bit condition, lubrication, handle isolation and the material affect the effort and time required.

    How harm can occur: A blunt bit or defective mounting can increase vibration, force and duration.

    Best practice to apply: Maintain the tool and consumables for the material; stop for abnormal vibration and verify repairs before return.

    Why this works: An efficient maintained tool avoids prolonged contact and avoids treating job rotation as the main control.

    Vibration at Work · What is hand-arm vibration and whole-body vibration?
  5. 5. Control compressed-air release

    What is happening: The hose and coupling contain energy independently of the operator's trigger position.

    How harm can occur: A failed connection or released hose can whip, strike or inject material; trapped air may remain after shutdown.

    Best practice to apply: Use the specified hose, connections and restraint arrangements; isolate and release stored pressure by the actual procedure before disconnection.

    Why this works: Removing the energy before opening the connection addresses the release mechanism directly.

    Vibration at Work · How is a defensible vibration assessment made?
  6. 6. Protect the surrounding work area

    What is happening: The compressor and breaking point also affect people who are not holding the tool.

    How harm can occur: Noise, exhaust, dust, flying fragments and trailing hoses can harm nearby trades and passers-by.

    Best practice to apply: Provide suitable ventilation, source controls, separation, route management and substance-specific precautions.

    Why this works: The task boundary must include bystanders and the compressor, not only the tool user's hands.

    Vibration at Work · What is hand-arm vibration and whole-body vibration?
  7. 7. Act on symptoms and changed work

    What is happening: Changes in grip, difficulty, numbness or tingling need a response rather than normalisation.

    How harm can occur: Continued exposure can worsen injury and make a worker less able to control the task.

    Best practice to apply: Report symptoms promptly and use occupational-health and exposure-review arrangements; do not diagnose HAVS from this model.

    Why this works: Early reporting can trigger preventive changes before more harm occurs; gloves are not a substitute for vibration control.

    Vibration at Work · When is health surveillance needed?
  8. 8. Separate servicing from production

    What is happening: Maintenance can expose stored air, hot parts and components held under load.

    How harm can occur: Unexpected operation or energy release can injure the fitter and the next user.

    Best practice to apply: Use competent task-specific shutdown, isolation and maintenance; update the equipment/exposure information after material changes.

    Why this works: A repair needs a verified return to work, not only a closed defect record.

    Vibration at Work · What evidence should management sample?

Illustrative awareness learning. Geometry, colours and movement do not establish safe distances, capacity, exposure, isolation or work permission. Use the actual assessment, equipment information and competent arrangements.

The wider workplace has its own account and subscription access. Exploring this lesson does not grant access, record course completion or authorise work.

UK guidance for further reading

HSE: Pneumatic breaking

What is hand-arm vibration and whole-body vibration?

HAV enters through hands holding or guiding vibrating tools or workpieces; WBV enters mainly through a seat or feet while operating vehicles or mobile machinery.

A breaker, grinder, drill, sander or hand-guided compactor can create HAV. A dumper, tractor, forklift or earth-moving machine on rough ground can create WBV and severe shocks. One person may experience both on a day, but the two exposure types have different assessment methods and legal values: do not add HAV and WBV numbers together. Noise, dust, force, posture and manual handling may need separate controls.

A daily vibration decision path
  1. Avoid the exposure Redesign or mechanise a vibrating task where feasible and check for risks introduced elsewhere.
  2. Use representative data Match vibration magnitude and actual trigger time to each tool or vehicle task.
  3. Assess the person’s day Add all hand-arm tasks for one worker; assess whole-body vibration separately, including shocks.
  4. Control and review Act before limits are exceeded, respond to symptoms and reassess after a tool, route or duration change.

Which symptoms need an early response?

Tingling, numbness, finger blanching, loss of grip or dexterity after tool work, and back discomfort associated with jolting vehicle work, should be reported and assessed promptly.

HAV can cause hand-arm vibration syndrome and carpal tunnel syndrome; continuing exposure can make harm permanent. WBV is associated with back pain, but posture, lifting and other work factors may contribute. Workers should not wait for a daily calculation or routine annual check before raising symptoms. A supervisor should review exposure and controls and seek occupational-health advice without making a diagnosis or disclosing confidential clinical details. See HSE.

SignalWork response
New HAV symptomsReport, review exposure and refer through OH route. Source
White fingers or lost dexterityDo not treat this as ordinary cold or fatigue; assess promptly. Source
Back pain after repeated joltsReview route, machine, seat, speed and other back-pain factors. Source: HSE whole-body vibration
How can hand-arm vibration affect blood flow, sensation and everyday hand function?
Interactive 3D anatomySHAREsim

How can hand-arm vibration affect blood flow, sensation and everyday hand function?

Interactive anatomy · Hand-arm vibration: circulation, sensation and function · Updated 2026-10-23

Read all anatomy and process explanations without the viewer

Normal function and example health effects, not a personal exposure calculator or clinical assessment. Whole-body vibration and back effects require a separate lesson. Trigger-time or safe-remaining-time calculations Symptom diagnosis, disease staging or fitness-for-work clearance Hand-colour based risk scores or glove-based clearance Personal health questionnaires, employer surveillance records or dexterity tests Warmth may alter episode context; it cannot erase lasting effects or return a cured state.

Hand surface

The hand combines blood supply, sensation, movement and support. The hand combines tissue support, blood supply, sensation and movement in the same small space. Use the skin outline, nail and joints as landmarks when opening the enlarged finger cutaways. The separated layers help identify different functions; they do not imply that vessels, nerves or tendons are normally detached from their neighbouring tissues. Health and Safety Executive: Hand-arm vibration: A guide for employees, INDG296

Digital artery

Small arteries carry blood towards finger tissues. Digital arteries carry blood towards the tissues of the fingers as part of the wider circulation. Trace the supply route into the enlarged finger before following the smaller vessels and the separate return route. The model enlarges the artery and uses symbols to make the direction clear; it does not measure the person’s blood flow. Manchester University NHS Foundation Trust: Blood Vessels

Small-vessel network

Smaller vessels distribute blood through the tissues. The small-vessel network distributes the blood supply through the finger tissues, supporting their need for oxygen and nutrients. Locate the branches between the larger supply and return routes. The pattern is a simplified teaching layout, not a scan of an individual’s vessels, and its size and colours are used to distinguish circulation from the nearby sensory pathway. Manchester University NHS Foundation Trust: Blood Vessels

Venous return

Veins return blood from the hand. Veins provide the return route for blood leaving the finger tissues, connecting the hand back towards the wider circulation. Follow the return arrow after tracing the arterial supply and smaller vessels. Supply and return form connected parts of the circulation; the blood does not stop permanently at the fingertip or become a sensory nerve signal. Manchester University NHS Foundation Trust: Blood Vessels

Sensory nerve

Sensory nerves carry information such as touch. Sensory nerves carry information such as touch from the hand towards the central nervous system. In the enlarged finger, follow the nerve separately from the blood vessels. The moving message is a symbol for communication, not a spark or liquid inside a tube. This pathway helps explain sensation without testing or diagnosing an individual’s nerve function. NHS: Peripheral neuropathy

Fingertip sensation

Feeling small objects helps with precise tasks. Fingertip sensation helps a person detect contact and handle small objects precisely. The sensory information works alongside the separate muscle and tendon system that moves the fingers. Use the small-object illustration to connect this function with an ordinary task. It is an explanation of why feeling matters, not a dexterity test or an assessment of a worker’s symptoms. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: Hand-arm vibration: Guidance on Regulations L140, second edition

Muscle and tendon

Muscles and tendons work together to grip and move. Muscles generate a pull that tendons transmit to the finger bones, allowing the joints to bend and the hand to close around an object. Trace the muscle–tendon relationship separately from nerves and vessels. The tendon carries mechanical force; the sensory nerve carries information, and the blood supply supports the living tissues involved. Gloucestershire Hospitals NHS Foundation Trust: Flexor Tendon Injuries

Joint

A joint allows neighbouring bones to move relative to one another. A joint is where neighbouring bones meet and can move relative to each other. Finger joints allow the hand to bend around a handle as muscles pull through tendons. Use their positions to orient the enlarged finger view and distinguish movement from the circulation and sensory pathways. This contextual structure does not depict a particular arthritis or establish an injury diagnosis. Health and Safety Executive: Hand-arm vibration: Guidance on Regulations L140, second edition · NHS: Arthritis

Tool contact

Vibration can enter the hand through a powered tool or vibrating workpiece. The source is outside the body. In the task view, an articulated hand wraps around a powered-drill handle. Tool and hand move together at the contact. Exposure depends on the actual equipment and how it is used; the visible movement is a teaching demonstration. Health and Safety Executive: Construction vibration questions · Health and Safety Executive: Hand-arm vibration: A guide for employees, INDG296

Cold-trigger context

Cold can trigger blanching episodes in people with vibration-related vascular effects. Cold is a context outside the hand. Warming may affect an episode; it does not prove lasting effects have gone away. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: Hand-arm vibration: Guidance on Regulations L140, second edition

Median-nerve cross-link

Carpal tunnel syndrome is a separate nerve-compression condition. It can also be associated with vibration exposure. The carpal-tunnel lesson explains the median nerve at the wrist separately. Health and Safety Executive: Hand-arm vibration: A guide for employees, INDG296 · NHS: Carpal tunnel syndrome

Open the complete process transcript

The process, step by step

Follow circulation

The hand needs a continuing blood supply to support its tissues. Arteries bring blood towards the fingers, smaller vessels distribute it through the tissues, and veins provide a return route towards the body. Start with the whole hand, locate the highlighted index finger and use the enlarged view to trace this supply-and-return arrangement. The skin, nail and joints help orient the cutaway. The vessels and flow symbols are enlarged for teaching rather than showing a person’s actual vessel sizes or circulation rate. Keep this route separate from the sensory nerve, which carries information rather than blood. Manchester University NHS Foundation Trust: Blood Vessels

What to watch: Find the highlighted index finger, then locate the artery, small-vessel network and venous return in the enlarged circulation view.

Why it matters: Circulation delivers the oxygen and nutrients that tissues need to function. The return route completes the local pathway, connecting the finger with the wider circulation rather than ending at the fingertip.

Explore this step: Trace the supply and return in order, using the nail and joints to keep your orientation in the enlarged finger.

Follow touch

Touch information from the finger travels along sensory nerves towards the central nervous system. This information helps a person feel contact and handle small objects, alongside the separate nerves and muscles that control movement. In the enlarged finger, locate the sensory pathway and compare its symbolic messages with the circulation route from the previous step. A nerve signal is communication, not blood flowing through another vessel. The fingertip and small-object illustration connect this internal pathway with a familiar task. They demonstrate why sensation matters for precise work; they do not test an individual’s nerve function or dexterity. NHS: Peripheral neuropathy

What to watch: Locate the fingertip sensory area and follow the sensory nerve in the enlarged cutaway, keeping it distinct from the blood vessels.

Why it matters: Sensation helps a person recognise contact and guide precise handling. It works alongside movement, but its information pathway has a different role from the blood supply and the muscle–tendon system.

Explore this step: Compare the sensory and circulation layers, then describe what each pathway carries and why both matter when holding a small object.

Locate the source

In the task view, the fingers bend around the drill handle and the thumb closes on the other side to form a grip. Muscles and tendons create finger movement; the contact between hand and handle provides a route by which vibration from powered equipment can enter the hand and arm. Locate the trigger and chuck to connect the body view with the external source. The illustrated hand and handle move together so this contact is clear. Their slowed, enlarged movement explains the pathway only; it does not calculate tool vibration, grip force, daily exposure or a safe operating time. Health and Safety Executive: Hand-arm vibration: A guide for employees, INDG296

What to watch: Find the fingers and opposing thumb around the handle, then locate the trigger and chuck to identify the powered tool as the source.

Why it matters: Grip allows the hand to guide equipment, but contact also links the external source to body tissues. This source-to-hand relationship explains why the actual tool and working method matter when assessing exposure.

Explore this step: Trace the contact from handle to fingers and thumb, and distinguish the visible teaching movement from an exposure measurement.

Separate the effects

Return to the healthy circulation and sensory layers before comparing the separate vibration-related examples. Blood vessels supply the tissues, whereas sensory nerves carry information about touch and other sensations. Vibration-related vascular and neurological effects can affect these functions differently and may occur independently. They are not compulsory stages that every person passes through in one sequence. Use the normal layer to identify the structure and its job, then compare only the corresponding example. A change in the illustration explains a possible mechanism; it does not diagnose a cause, determine severity or predict the outcome for a particular worker. Health and Safety Executive: Hand-arm vibration: Guidance on Regulations L140, second edition

What to watch: Compare the artery and sensory nerve with their own normal layers, using the labelled finger structures to keep the two functions separate.

Why it matters: Separating these functions makes the examples easier to understand and avoids treating one symptom pattern as proof of another. Normal circulation and sensation provide different reference points for the two explanations.

Explore this step: State the normal job of each structure, then compare one example at a time without placing the effects in a compulsory order.

Change the work

The prevention step takes attention back to the work that creates exposure. Consider whether the process can avoid hand-held vibration, then examine suitable lower-vibration equipment, maintenance and the way exposure is planned across the task. These choices act on the source and the contact route shown earlier. Warmth and suitable clothing address cold conditions, but gloves should not be treated as reliable vibration protection. Use the task illustration to consider where a change in equipment or work organisation would act. Discussing prevention does not represent the repair of nerves or blood vessels. The model does not establish whether a particular workplace arrangement is adequate. Health and Safety Executive: How employers can protect workers from hand-arm vibration · Health and Safety Executive: Construction vibration questions

What to watch: Return to the hand–handle contact and the surrounding task, and consider where a change in equipment or work organisation would act.

Why it matters: Changing the work can reduce the vibration that reaches the hand. Linking a control to the source and contact route helps explain its purpose, separately from the medical assessment of any existing symptoms.

Explore this step: Identify which part of the source-to-hand pathway a proposed work control would change. The model does not provide an interactive control comparison.

Mechanisms and their limits

Vascular example: reduced finger circulation Vibration-related vascular effects can include episodes of reduced finger blood flow. Cold may trigger blanching. Flow returning can be painful. Fewer arrows and patterned episode frames illustrate reduced flow; they are not a measured severity scale. Finger appearance varies. Colour alone cannot establish HAVS or occupational causation. No artery is shown full of debris, and warming does not mean the condition is cured. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: Hand-arm vibration: Guidance on Regulations L140, second edition · NHS: Raynaud’s

HSE: protect workers from hand-arm vibration

HSE: recognise and report hand symptoms

Sensory example: altered feeling Numbness, tingling and reduced feeling may occur without a blanching episode. The sensory comparison keeps the skin appearance unchanged and alters only the labelled signal. The nerve is not depicted as severed. This is a functional illustration, not a scan. Absence of white fingers does not exclude vibration-related health effects. Other conditions can also cause similar symptoms. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: Hand-arm vibration: Guidance on Regulations L140, second edition · NHS: Peripheral neuropathy

HSE: symptoms and early reporting

HSE: exposure controls

Everyday function: grip and fine tasks Reduced sensation or strength can make handling small objects and working with tools harder. This example connects several possible effects to everyday function. A small-object illustration is not a clinical dexterity test or a disease stage. Symptoms differ between people. The viewer does not decide fitness for work or continued tool use. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: Hand-arm vibration: Guidance on Regulations L140, second edition · Health and Safety Executive: Hand-arm vibration: A guide for employees, INDG296

HSE: control exposure and arrange appropriate assessment

HSE: advice for employees

Vascular example: reduced finger circulation — follow the anatomy

Look at: The small blood vessels supplying the fingers.

What changes: Vessels can narrow during an attack, reducing blood flow to the fingertips.

Why it matters: Fingers may turn white and feel cold; returning circulation can be painful.

What to do: Reduce vibration at source, keep hands warm and report early symptoms.

Repeated breaker use and a later cold-triggered episode

Road maintenance: a worker regularly uses a concrete breaker, then later experiences a cold/wet episode affecting finger circulation. Explicit time jump across repeated vibration exposure and a later cold trigger. Vascular disease does not develop during 32 seconds of tool use. Cold-triggered colour change is not a diagnostic test or proof of occupational cause. Warmth does not reverse established injury.

Identify the vibration source The breaker transmits vibration through the handle to the hands. Review whether the work can be done another way and whether suitable lower-vibration equipment is available. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: How employers can protect workers from hand-arm vibration

Repeated exposure, then a later cold context The timeline jumps across repeated work to a later cold/wet episode. Tool vibration and cold are different factors, not two names for the same injury. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: How employers can protect workers from hand-arm vibration

Possible circulation effects An illustrative narrowed finger-vessel pattern explains impaired blood supply during an episode. Labels and texture carry meaning; a skin colour or flow animation cannot diagnose HAVS. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: Hand-arm vibration: Guidance on Regulations L140, second edition · NHS: Raynaud’s

Act early on exposure and symptoms Report symptoms promptly and arrange appropriate occupational-health advice. Review method, tool selection, maintenance and exposure management; keeping warm is supportive, not a substitute for vibration controls. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: How employers can protect workers from hand-arm vibration

Sensory example: altered feeling — follow the anatomy

Look at: The sensory nerves running into the fingers.

What changes: Repeated vibration can damage nerves and alter the signals they carry.

Why it matters: Tingling or numbness can affect touch, even without white fingers.

What to do: Use lower-vibration methods, limit exposure and report changes in sensation.

Needle-scaler work and later reduced fingertip sensation

Fabrication maintenance: repeated hand-held needle-scaler use is followed by a separate example of altered sensation. Explicit time jump: cumulative nerve effects and later symptoms are not real-time results from this 32-second task illustration. Numbness can have several causes and can occur without white-finger episodes. This is not whole-body vibration or a self-administered sensitivity test.

Notice repeated hand-tool exposure A needle scaler is used for repeated surface preparation. Consider alternative processes and suitable equipment before treating the tool vibration as unavoidable. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: How employers can protect workers from hand-arm vibration

A separate cumulative exposure period The timeline moves across repeated exposures. Sustained vibration can affect sensory structures; no personal exposure value, trigger time or nerve-damage dose is calculated. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: Hand-arm vibration: Guidance on Regulations L140, second edition

Sensory signals may be affected The nerve example changes the labelled touch-signal path towards the fingertip. Tingling or reduced sensation does not require the vascular layer to turn white or a tendon to tear. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: Hand-arm vibration: Guidance on Regulations L140, second edition · NHS: Peripheral neuropathy

Report and reduce the source Arrange early reporting and suitable assessment, and review the task, maintained tools and exposure management. The controls change future work demands; they do not animate damaged nerves back to normal. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: How employers can protect workers from hand-arm vibration

Everyday function: grip and fine tasks — follow the anatomy

Look at: The fingertips, nerves and muscles used for a controlled grip.

What changes: Loss of sensation and strength can make fine hand movements harder.

Why it matters: Small objects, fasteners and safe tool handling may become more difficult.

What to do: Change the work to reduce exposure and seek occupational-health advice promptly.

From vibrating workshop tools to difficulty with small fasteners

A repair worker with repeated vibration exposure later notices difficulty handling screws and other small items. Explicit time jump from a work-exposure history to a later functional example. No speed or dexterity score is used to diagnose disease. This card shows what health effects can mean in daily work, not a third universal lesion or a test that clears someone to use a tool.

Understand the worker’s actual tasks Grinders and other hand-held tools may be used across maintenance jobs. Review the combined work pattern rather than judging one short demonstration. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: How employers can protect workers from hand-arm vibration

Move forward to a reported difficulty The timeline jumps to a later task involving small fasteners. The worker describes reduced feeling or grip; the learner is not asked to prove symptoms through a timed challenge. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: Hand-arm vibration: A guide for employees, INDG296

Explain function without inventing a lesion Changes in sensation or hand strength can make small objects harder to manipulate. Nerve, tendon, muscle and joint labels stay distinct; the picture cannot identify the individual cause. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: Hand-arm vibration: A guide for employees, INDG296

Take the report seriously Arrange appropriate occupational-health advice and review tasks and equipment. Suitable aids and exposure reduction support safer work; there is no automatic fitness decision, cure animation or glove-based clearance. Health and Safety Executive: Worried about your hands? · Health and Safety Executive: How employers can protect workers from hand-arm vibration

Read the practice situations and all answer explanations
HV-Q1: What is the appropriate response?

A tool user reports tingling but has not noticed white fingers.

Exclude HAVS because there is no blanching. — Sensory effects can occur without circulation changes. The absence of blanching does not exclude a problem.

Report the symptoms promptly and arrange appropriate assessment. — Yes. Report early and obtain appropriate assessment. Review the exposure controls instead of waiting for visible changes.

Use the hand image to diagnose a disease stage. — The viewer cannot diagnose or stage disease. Similar symptoms may have other causes.

Health and Safety Executive: Worried about your hands? · Health and Safety Executive: Hand-arm vibration: Guidance on Regulations L140, second edition · Health and Safety Executive: Hand-arm vibration: A guide for employees, INDG296
HV-Q2: Which review is needed?

A contractor proposes anti-vibration gloves as the only control.

Approve the gloves because they remove vibration risk. — Gloves are not an effective replacement for controlling vibration exposure.

Consider avoiding vibration, suitable lower-vibration equipment, maintenance and exposure management; gloves may help warmth. — Correct. Address the source and work method. Suitable gloves may keep hands warm but must not be relied on for vibration protection.

Use warm fingers as proof the exposure is safe. — Warmth is not an exposure measurement and cannot provide clearance to work.

Health and Safety Executive: How employers can protect workers from hand-arm vibration · Health and Safety Executive: Construction vibration questions
HV-Q3: How should exposure be assessed?

Two different vibrating tools were used in a shift.

Choose a hand colour to calculate safe remaining minutes. — Hand appearance cannot calculate exposure or a safe time. This viewer produces no exposure result.

Use reliable exposure information and an appropriate separate assessment method. — Yes. Consider the relevant tools and processes, using suitable vibration and use-time information in a separate assessment.

Count only the tool used for longest. — More than one tool or process can contribute. Do not discard the other exposure.

Health and Safety Executive: How employers can protect workers from hand-arm vibration · Health and Safety Executive: Construction vibration questions
Sources and how the model is made

The opening images are AI-generated anatomical illustrations. The interactive 3D models and labelled SVG diagrams use original procedural artwork. These teaching images are not medical scans or diagnostic tools. Source references support the learner explanations and do not grant artwork rights.

· Three.js MIT licence

How is a defensible vibration assessment made?

Identify each exposed person and source, use a representative in-use vibration magnitude and actual exposure duration, then calculate or reasonably estimate the complete daily exposure.

Observe real tasks and ask workers about tools, workpieces, grip, materials, surfaces, route, speed, jolts and symptoms. Include occasional high-exposure work and people at particular risk. Use reliable HSE, supplier or workplace data that represent these conditions; measure with a competent person where suitable data cannot be obtained. Record assumptions, controls, actions, owners and review triggers. A shift length is not hand-tool trigger time, and engine-on time is not necessarily representative WBV exposure. See HSE.

InputCheck
MagnitudeRepresents tool/vehicle, condition and work mode. Source
DurationActual exposure, not attendance or planned shift. Source
Daily mixEvery relevant source for that worker and day. Source
UncertaintyConservative estimate, further data or task hold where decision may change. Source

How do HAV trigger time and points work?

For a single steady task, A(8) = a × √(T/8), where a is the representative frequency-weighted vibration magnitude in m/s² and T is actual exposure in hours. Divide the exposure hours by eight before taking the square root. HSE points add contributions from each HAV tool used by that person that day.

Worked illustration only: a representative 5 m/s² tool used for two hours of actual trigger time yields 5 × square root(2/8) = 2.5 m/s² A(8), or 100 HSE points. That reaches the action value before any other vibrating tool is used. If another tool is used, enter both magnitudes and durations in the HSE calculator and assess the combined daily total; do not compare each tool in isolation or turn the example into a universal safe-use time. Tool magnitude and time vary by job and operator.

Illustrative inputResultDecision
5 m/s² for 2 actual trigger hours2.5 m/s² A(8), 100 points.EAV reached; controls required. Source: HSE
Second HAV tool on same dayAdd its points to the first task.Re-plan the total daily exposure. Source: HSE
Unknown or non-representative dataNo defensible daily total yet.Get reliable data or change/hold the task. Source: HSE

Build the whole day from representative tool use

For hand-arm vibration, combine the contributions from each tool using representative vibration magnitude and actual trigger time. Whole-body vibration has a separate assessment method; do not add a vehicle exposure to a hand-arm vibration points total.

Inspection of a hand-held breaker and vibration sensor. Photorealistic illustration.
Illustrative UK workplace scene. Read the practical checks below for responsibilities, evidence and limits. Download image · Download smaller image · Print-ready teaching sheet (PDF)
  1. Establish credible inputs

    Record each tool, task, material and condition, the source and relevance of the magnitude estimate, and its uncertainty. A declared value is not automatically representative of the work. Tool inspection and a photograph do not measure exposure.

  2. Count time when vibration reaches the hands

    Use actual trigger or contact time for the task, including repeat work and other vibrating tools. Elapsed shift time or a nominal job duration can misrepresent the dose. Keep the existing worked example in its stated conditions.

  3. Combine the hand-arm vibration day

    Use the appropriate HSE calculator or competent assessment for each partial exposure and the daily total. Recalculate if tools, materials, condition or time change. Control exposure at source before relying on rotation or an estimated time allowance.

  4. Keep vehicle vibration and health decisions distinct

    Assess rough routes, shocks, vehicle condition, seating and posture through the whole-body vibration route. Seek suitable health-surveillance advice for HAV risk; a numerical exposure estimate or anatomy model cannot diagnose disease or clear someone for work.

Hold the task if the combined exposure cannot be justified, a control fails or symptoms require prompt reporting and review. Never present an estimated allowance as a guarantee of safety.

How is WBV assessed without borrowing HAV rules?

Assess vehicle and task exposure through the seat or feet, including roughness, speed, shocks and time, against the WBV daily values; HAV tool points are not a WBV calculator.

Look at road or ground condition, vehicle type and suspension, seat adjustment, tyres, load, driving pattern and repeated jolts. Consider awkward posture, climbing, lifting and other contributors to back pain. HSE notes many WBV problems can be reduced through simple site and machine changes without routine measurement. Competent assessment or measurement may be needed when the exposure category or effectiveness of controls remains uncertain. See HSE.

QuestionEvidence
Are large jolts present?Observe route and operator experience; address shocks promptly. Source
Is the seat effective?Correct adjustment, suspension condition and driver training. Source
Is the route avoidable?Layout, maintenance, speed and transport need. Source
Can exposure be estimated?Representative task/vehicle data; competent measurement if needed. Source

Can a manufacturer label or a wearable prove exposure?

No single declared emission value, tool tag, timer or wearable proves an individual worker's daily A(8); it can support an assessment only when its data and assumptions fit the real task.

Manufacturer declarations are useful for selection and initial estimates, but standard test conditions may differ from actual material, accessory, maintenance and use. A timer can help estimate actual trigger time, while a wearable may be a proxy rather than a handle vibration measurement. HSE reports different electronic systems varying by up to about 20% on the same task and says continual daily monitoring is not usually needed. If a result matters to an EAV/ELV decision, validate it and express HAV as A(8) or HSE points.

How should stronger source controls be chosen?

Start by avoiding the hazardous task or release, then use suitable substitution and physical controls before relying on work rules or personal protection.

The order guides a decision; the actual control depends on this task, the people exposed and what a change could introduce. A supervisor should observe the control during real work, hold a failed task and obtain a competent release after correction. HSE guidance for this control decision

Control layerTask decision
AvoidAvoid unnecessary vibrating work
Substitute or reduceChoose an efficient lower-vibration method for the task
EngineerUse supported tools, sound consumables and maintained vehicle routes
Organise and verifyAssess each person’s combined day and stop for symptoms or changed exposure
Protect residual exposureGloves do not establish vibration compliance

How do controls change across industries?

The same control principle needs a different design and stop decision when the task, equipment and people change.

A vibrating source is not the same as a daily personal exposure. The material, ground surface, tool condition, task duration and worker vary across sectors, so the strongest practical control and stop point must be chosen for each job. See HSE.

Sector, task and peopleExposure and harmStrongest feasible controlCheck or stop point
Manufacturing: grinding castings; grinder operator.Repeated grip exposure can damage hand nerves and circulation.Remove grinding need in casting design where possible; use lower-vibration tooling and maintained discs.Recalculate all tool time; stop on numbness, defect or likely excess. Source
Construction: breaking concrete; breaker operator and crew.High HAV magnitude and long trigger time raise HAVS risk.Use machine-mounted breaking or cut/replace method where feasible; control remaining tool time.Check actual task and tool; hold when magnitude or cumulative time is unknown. Source
Hospitality: grounds maintenance; mower or strimmer operator.Hand tools produce HAV; ride-on equipment can transmit WBV and jolts.Choose task-suitable low-vibration equipment and smooth routes; maintain blades and seats.Assess HAV and WBV separately; stop on repeated shocks or symptoms. Source
Logistics: forklift over rough yard; driver.Seat and floor transmit WBV and shocks, adding to back risk.Repair route, control speed and load, and use correctly adjusted maintained seat.Stop repeated jolts or a failed seat; review route and vehicle before restart. Source

Which controls cut HAV exposure at source?

First avoid or mechanise vibrating hand work; then choose a task-suitable lower-vibration process and maintain tool, accessory and workpiece so both magnitude and trigger time fall.

Use excavator attachments, off-site fabrication or non-vibrating methods when practicable. Select a tool that completes the real task efficiently; a small low-emission tool can cause more total exposure if it takes much longer. Keep bits sharp, discs balanced and parts sound. Support the tool or workpiece, use manufacturer-recommended technique and avoid unnecessary grip force. Breaks and rotation can reduce an individual's exposure only if work is genuinely redistributed and no one else exceeds their plan. See HSE.

ControlVerification
Avoid/mechaniseHand exposure removed or materially reduced. Source
SelectRepresentative magnitude and task duration both considered. Source
MaintainBits, bearings and accessories in condition. Source
PlanActual combined daily exposure checked for each person. Source

Which controls cut WBV and shocks?

Reduce the need to drive and the jolts at source: improve routes and ground, select suitable vehicles, maintain suspension, tyres and seats, and train drivers to use appropriate speed and posture.

Fill potholes, grade routes, avoid steps and repeated crossings, and place material to reduce travel. Match plant to surface and load; maintain seat suspension and adjust it for the operator. Reduce speeds where jolts occur, without creating other traffic hazards. Time sharing and breaks may support control after the source has been improved, but there is no WBV personal protective equipment that substitutes for these measures. See HSE.

ControlCheck
Site/routePotholes, transitions, distance and detours. Source
MachineSuspension, tyres, load and maintenance. Source
Seat/operatorAdjustment, posture and driving practice. Source
Work planDuration and other back-pain tasks reviewed. Source

Do anti-vibration gloves solve HAV risk?

Usually not. Do not credit anti-vibration gloves as the primary exposure reduction; suitable gloves and clothing can keep hands warm and dry, which supports circulation.

HSE says glove attenuation is difficult to predict in real tool use and can be ineffective or even increase vibration at some frequencies. Thick gloves may reduce dexterity or increase grip force. Select gloves for warmth and other task hazards without creating entanglement or loss of control, but calculate and reduce exposure through method, equipment and work planning.

What should be checked before vibrating work starts?

Confirm the task, person, equipment and expected exposure match the assessment, then inspect the tool or vehicle and the controls that keep magnitude and time down.

For HAV, check tool, bit/disc, handles, mountings, workpiece support, planned trigger time and any other HAV task that day. For WBV, check route, ground, tyres, seat and suspension, load and expected jolts. Confirm training, symptom-reporting route, health-surveillance arrangements where required and a supervisor who can change the plan. A tag or dashboard is a prompt to ask questions, not permission to start. See HSE.

HAV before-useWBV before-use
Tool and accessory condition.Route and ground condition. Source
Representative magnitude and combined day.Vehicle, tyre, suspension and seat condition. Source
Work support and method.Load, speed plan and back-pain factors. Source

What changes during work or at hand-back?

Track actual exposure and conditions, pause when they depart from the plan, then record use, defects and any symptoms before handing equipment or routes back.

A harder material, blunt bit, abnormal tool vibration, longer drilling, extra job or repeated vehicle jolt can change the daily risk. Do not silently transfer a task to another worker with the same unassessed exposure. On completion, capture actual trigger time or driving conditions with enough detail to improve the assessment, report defects, isolate unsafe equipment and close corrective action. Keep clinical symptom details in the appropriate confidential route.

When must vibration work be held or stopped?

Hold a task when credible exposure may exceed the relevant ELV, the control plan is invalid, a tool or vehicle defect increases vibration, severe shocks persist or symptoms need assessment.

If an ELV is exceeded, reduce exposure immediately, establish the cause and amend controls to prevent recurrence. A missing reliable magnitude or duration is not automatically an ELV breach, but high-risk work should not proceed on an invented calculation. Stop a defective machine safely, protect others from the work-area hazard, tell the supervisor and obtain competent exposure or engineering advice. Restart only when the method, equipment and whole-day plan are defensible and the worker is appropriately advised. See legislation.gov.uk.

TriggerHold and restart basis
Likely ELV exceedanceStop/re-plan; verify total below limit and lower as reasonably practicable. Source
Unknown high-risk tool exposureGet representative data or choose lower-risk method. Source
Damaged tool, seat or rutted routeRepair/change, then inspect and reassess. Source
HAV symptoms or severe back complaintPrompt reporting and OH/medical route; adjust work as advised. Source

When is health surveillance needed?

Provide risk-based HAV health surveillance and respond promptly to symptoms. After a doctor-confirmed HAVS or carpal tunnel syndrome diagnosis, the employer or responsible person must check the relevant GB or NI RIDDOR disease-reporting conditions and report when they apply; symptoms alone are not a diagnosis.

Surveillance is repeated health checking, not an exposure-control substitute or permission to work at the ELV. A competent occupational-health scheme uses screening, escalation and clinical advice when indicated; managers receive fitness and control advice, not unnecessary medical detail. For WBV, assess back-pain risk and symptoms with occupational-health input where appropriate; do not assume the HAV questionnaire is a universal WBV programme. Maintain health records as law requires and consult workers on arrangements. See legislation.gov.uk.

Following a confirmed diagnosis, check the specified work-exposure link rather than reporting every symptom or diagnosis automatically. In Great Britain, RIDDOR 2013 regulation 8 covers diagnosed HAVS where work regularly uses percussive or vibrating tools or holds vibrating material, and diagnosed carpal tunnel syndrome where work regularly uses percussive or vibrating tools. HSE says employees provide the doctor's diagnosis in writing to the employer; the self-employed route can use a verbal diagnosis. In Northern Ireland, use the separate RIDDOR (NI) 1997 and HSENI disease route after written medical advice, checking that the diagnosed condition and occupational exposure meet that regime. Keep clinical details confidential and share only the information needed for lawful reporting, fitness advice and control review. Early symptoms, an isolated back-pain complaint, or carpal tunnel syndrome without the specified work link are not automatically reportable.

SituationResponse
Regular HAV above EAV or health riskSuitable surveillance and control programme. Source
New tingling, numbness or blanchingPrompt OH referral and exposure review; symptoms alone are not a RIDDOR disease diagnosis. Source
WBV-related back concernReview shocks and ergonomics; seek competent health advice. Source
Adverse surveillance trendInvestigate controls across similar workers/tasks. Source
GB doctor-confirmed HAVS or CTS with the specified work exposureEmployer or responsible person checks and, if required, reports under GB RIDDOR 2013 regulation 8; protect clinical confidentiality. Source
NI doctor-confirmed HAVS or CTS with the relevant work exposureEmployer or responsible person checks and, if required, reports through the separate NI RIDDOR 1997 and HSENI disease route. Source

What must workers and supervisors know?

Explain the health effects, action and limit decisions, task controls, correct equipment use, defect reporting, symptom route and who can hold or restart work.

Practise estimating actual trigger time and checking all HAV tools in the day, not reciting a generic number of minutes. Drivers need route, speed and seat instruction plus a way to report potholes and jolts. Supervisors need to spot unreliable emissions data and a tool not matched to the job. Consultation with workers helps identify real exposure patterns and whether controls are practical. See legislation.gov.uk.

How should two vibrating tools be planned in one shift?

At BuildOut Ltd, a supervisor uses representative magnitudes and actual trigger time for both tools, then applies the combined HAV result before work is released.

A worker will drill concrete anchors and later grind a bracket. The drilling illustration alone uses 5 m/s² for two actual trigger hours, reaching 100 points. Grinding adds exposure; it does not start a new allowance. The supervisor changes the method or allocates work to keep each person's daily exposure controlled, records the assumptions and checks whether material or accessories change. The calculation is illustrative, not a site-approved duration. See HSE.

GateDecision
BeforeGet representative magnitude and time for both tasks. Source
DuringUpdate the total if drilling runs longer or grinding changes. Source
Hand-backRecord actual time, tool condition and revised plan. Source

BuildOut two-tool day

Task material and setting: Concrete anchor drilling and steel-bracket grinding on a construction site.

People and prerequisites: Trained worker and supervisor; task-suitable tools, reliable in-use magnitudes and a full-day HAV plan.

Before: Check bits/discs, work support and actual trigger-time estimates for both tools; 5 m/s² for two drilling hours alone reaches 100 points.

During: Record real trigger time and add grinding exposure; stop for blunt bits, extra work or abnormal vibration.

Hold or stop: Hold if combined exposure cannot be defended, controls fail or planned exposure approaches the ELV.

Completion and hand back: Log times and condition; replan remaining work or release sound equipment for next user.

Evidence: Assessment inputs, HSE calculator result, plan change, defect/repair and supervisor decision.

Finish the two-tool calculation

For teaching only, suppose representative drilling at 5 m/s² lasts two trigger hours: 100 points. A grinder at 5 m/s² for one trigger hour adds 50 points. Total HAV exposure is 150 points and combined A(8) is 2.5 × √(150/100), approximately 3.06 m/s². This exceeds the action value and is not a planned allowance. The supervisor chooses a changed method, reduces exposure as low as reasonably practicable, and verifies representative inputs and the revised full-day total. WBV stays separate. See Vibration risk assessment: worked HAV example.

What if a contractor arrives with an unverified grinder?

BuildOut should hold the vibrating task until the host and contractor agree a task-matched assessment, suitable equipment and responsibility for each worker's full-day exposure.

A grinder label gives a declared emission but no defensible in-use value for the selected disc and material; the contractor also used a breaker earlier. A wearable reports time only. The host checks the method, disc, maintenance, other exposures and who will supervise. The work starts only after a defensible estimate and controls; site tags and contractor paperwork alone cannot release it. See HSE.

BuildOut contractor grinder gate

Task material and setting: Grind a steel fixing using a contractor tool after earlier breaker work.

People and prerequisites: Host supervisor, contractor supervisor and worker; agreed task method, tool condition and whole-day exposure account.

Before: Check selected disc, material, condition, representative magnitude and earlier HAV exposure.

During: Use verified method and actual trigger-time record; monitor changed material or tool behaviour.

Hold or stop: Do not accept a label, tag or wearable alone; hold when magnitude or combined exposure is unresolved.

Completion and hand back: Record actual use and any defect; agree remaining-work plan across host and contractor.

Evidence: Contractor assessment, tool data basis, combined calculation, host decision and hand-back.

What if a dumper route causes repeated jolts?

Stop using the route or machine as planned, correct the source of shocks and reassess WBV and other back-pain factors before repeated trips resume.

At BuildOut, a dumper operator reports jolts and back discomfort on a rutted temporary road. The supervisor diverts traffic where safe, checks ground, speed, tyre and suspension condition, seat adjustment and load. Facilities repairs the route and maintenance corrects any vehicle fault. A competent person confirms the revised operation and the worker receives appropriate health advice. A lower speed alone should not become a permanent substitute for repairing the route. See HSE.

BuildOut dumper route response

Task material and setting: Carry spoil by dumper over a rutted temporary site road.

People and prerequisites: Driver, traffic supervisor, route owner, maintenance and OH support; safe alternative route and vehicle check.

Before: Inspect route, load, tyres, suspension and adjusted seat; establish expected trip pattern.

During: Repeated jolts and back discomfort trigger a safe stop and report.

Hold or stop: Keep affected route or machine out of the plan until shocks and defects are addressed.

Completion and hand back: Repair/grade route, service machine if needed, observe a representative trip and support worker health follow-up.

Evidence: Route defect, vehicle check, repair, reassessment, driver briefing and release decision.

Which changes require reassessment?

New tools, accessories, materials, operators, work rates, routes, vehicles, seats, health findings or significant defects can invalidate the exposure estimate and control plan.

Do not copy an A(8) from another project where the material and method differ. A higher work rate changes trigger time; a blunter bit may raise both time and magnitude. A road that deteriorates after rain can alter WBV shocks. Review after a health-surveillance concern and after controls are installed to confirm they work.

How is competence demonstrated at each level?

Learning should match the decision a person makes, with a practical check and reassessment after change.

Training must show that a person can apply the right method to their own job. An awareness briefing is not authorisation to set tool times, measure WBV or interpret a medical finding. See HSE.

Role or levelTask learningDemonstration and assessorRecord and reassessment
Everyone nearbyKnow symptoms, reporting and why exposures differ.Supervisor checks a clear report and escalation route.Induction record; refresh after new task or advice. Source
Tool users and driversChoose, inspect and use equipment; record actual trigger or driving conditions.Assessor watches a real tool/vehicle task and a stop decision.Task authorisation; reassess after tool, route or symptom change. Source
Maintainers and specialistsMaintain bits, bearings, tyres, suspension and seats to specification.Competent lead observes repair and verifies performance.Maintenance log; reassess after modification or repeat defect. Source
SupervisorsCombine all HAV tasks, distinguish WBV and manage changed duration.Manager checks a representative worker-day estimate and hold decision.Assessment and allocation record; reassess after job change. Source
Managers and purchasersSelect efficient low-vibration methods and resource controls and surveillance.Technical adviser challenges emission data against actual use.Procurement/assurance record; review with worker feedback. Source
Hygienists, occupational health and auditorsEvaluate exposure uncertainty, symptoms and confidential health route.Relevant specialist lead reviews method and referral/audit judgement.Scope, result and action record; reassess after new evidence. Source

How do product data and workplace duties differ?

Manufacturers provide equipment information; employers must assess each person’s actual hand-arm and whole-body exposure.

A declared emission value comes from a stated test condition and may not match the job. Choose tools by representative magnitude and task efficiency, then combine each worker’s hand-arm tasks for the day. Whole-body vibration needs its own route, vehicle and shock assessment. HSE L140 and L141 provide the regulator’s assessment and control guidance; a supplier figure is not a universal safe-use time.

What evidence should management sample?

Trace real tasks from equipment choice and exposure inputs through control, worker practice, defects, health feedback and corrective-action close-out.

Sample mixed-tool days, not only the highest single-tool label. Observe actual trigger time and whether a low-vibration choice slows the job. Inspect route defects and ride quality for WBV. Check that health-surveillance signals prompt control review and that confidential clinical records remain separate from operational decisions. Review whether each planned action has an owner, date and evidence of effectiveness.

EvidenceFailure signal
Representative magnitude and durationTag copied without task match or shift time used as trigger time.
Source controlsBlunt parts, broken seat or unfilled potholes.
Worker feedbackSymptoms or jolts dismissed because dashboard is green.
ClosureRepair done but no reassessment or restart decision.

What do the acronyms and key terms mean?

Expand each abbreviation at first use and keep its practical meaning attached to the task.

TermFull expansionMeaning in this task
HAVHand-arm vibrationVibration entering the hand from a tool or workpiece.
WBVWhole-body vibrationVibration and shocks entering through a vehicle seat or floor.
HAVSHand-arm vibration syndromeCondition affecting hand circulation and nerves; clinical diagnosis is separate.
EAVExposure action valueDaily level that triggers specified action, not a tool emission limit.
ELVExposure limit valueDaily exposure that must not be exceeded.
A(8)Eight-hour-equivalent daily exposureCombines vibration magnitude and duration for one person’s day.
Trigger timeTime hands contact a vibrating sourceDifferent from total job or shift time.
CTSCarpal tunnel syndromeA nerve condition that can be vibration-related; diagnosis requires a clinician.

Which BuildOut documents support this topic?

Download individual editable BuildOut documents for this topic. Procedures and plans contain completed arrangements; forms, checklists, assessments, RAMS and permits are blank masters. Registers include separate worked examples.

DocumentPurpose and contentEditable download
Vibration exposure assessment and control procedure
BOUK-PRO-VIB · Completed worked example · v1.0
Select low-vibration methods, estimate realistic trigger times, maintain tools and refer symptoms.Download DOCX
Read preview
Hand-arm vibration task/exposure assessment
BOUK-RA-VIB-01 · Blank editable master · v1.0
Use reliable task data and realistic trigger times to reduce exposure.Download DOCX
Read preview
Whole-body vibration and plant-route assessment
BOUK-RA-VIB-02 · Blank editable master · v1.0
Evaluate vehicle, ground, seat, speed and duration influences.Download DOCX
Read preview
Vibration exposure-control and tool-use record
BOUK-FRM-VIB-01 · Blank editable master · v1.0
Verify planned controls and investigate unexpected task duration.Download DOCX
Read preview
Vibration symptom and health-surveillance referral
BOUK-FRM-VIB-02 · Blank editable master · v1.0
Escalate symptoms and arrange competent surveillance where risk indicates.Download DOCX
Read preview
Vibration-tool selection and maintenance check
BOUK-CHK-VIB-01 · Blank editable master · v1.0
Check suitable low-vibration equipment, consumables and maintenance.Download DOCX
Read preview

Review and adapt the documents for your organisation, activities and jurisdiction before approval and issue. Open the SHAREms management-system hierarchy to find each document under its parent policy.

Return to SHARE home

Practise the checks in 3D

Follow the highlighted check, compare a sound part with a fault, and see how a missed fault can cause harm. Then use the matching blank checksheet to record what you actually find.

Browse all 25 checksheets and 26 demonstrators

Documents to download

Download editable resources from the SHAREhub environment to support your work. Working forms and spreadsheet input areas are blank. Reports, plans, guides, briefings, procedures and policies contain completed fictional example content to adapt.

Return to SHARE home