Pressure systems and stored energy awareness · detailed source study

Optional reference study from the SHAREhub topic pages and selected source records used for this course. The core learning-time estimate excludes this extended reference.

A written scheme, report and maintenance record differ
A written scheme, report and maintenance record differ

Source: work-equipment-lifting-equipment-and-pressure-systems--practical-interim-work-equipment-lifting-equipment-and-pressure-systems

Several regimes can apply to one asset. A competent examination plan, completed findings and maintenance evidence answer different questions. Identify vessel, connected pipework, protective devices and the actual boundary through the competent pressure-system process. The applicable scheme defines the scope and requirements for examination; it is not evidence that examination has been completed. An examination report records findings and actions. A maintenance record records work done; neither automatically closes the other’s requirements. The competent owners resolve applicable evidence and restrictions before use. Lifting planning and examination have their own route; no pressure settings, venting steps or intervals are supplied. ERICPD is a planning cross-map: Discipline verifies and sustains every control. ESEAP compares effectiveness.

A label does not authorise the task; retain the owner, evidence and stop or change decision.

What should a worker do before using work equipment?

Source: work-equipment-lifting-equipment-and-pressure-systems--first-actions

Confirm the equipment is the right type for the task, check guards and controls, inspect for obvious damage, understand the safe method and emergency response, keep others clear, and stop if condition or permission is uncertain. 2 linked parts. Follow the question numbers and complete the applicable route.

Part 1 of 2 · Questions 1–3 Source basis: GOV.UK placing UKCA or CE marked products on the Great Britain market · Provision and Use of Work Equipment Regulations 1998 · HSE INDG229 Using work equipment safely · HSE Introduction to work equipment and machinery · HSE L22 Safe use of work equipment · GOV.UK placing CE or CE and UKNI marked products on the Northern Ireland market · Provision and Use of Work Equipment Regulations Northern Ireland 1999 · HSE PUWER guidance and topic index · GOV.UK product regulations by sector and current marking approaches.

Confirm the equipment is the right type for the task, check guards and controls, inspect for obvious damage, understand the safe method and emergency response, keep others clear, and stop if condition or permission is uncertain. A machine, lifting device or pressure system may have overlapping duties, but a single certificate does not close every risk. Apply it: Which part of this plan would you check at the workface before authorising the task? A machine, lifting device or pressure system may have overlapping duties, but a single certificate does not close every risk. Identify the actual task and equipment, apply the workplace-use rules, then test whether lifting or qualifying pressure-system duties add planning, examination, written-scheme and competent-person requirements.

Authorisation, pre-use check, task briefing, any defect report and supervisor release. Apply it: What evidence would show that the change improves this task, rather than only completing a record? Setting: A fictional workshop receives an identified air-receiver system with connected pipework and protective devices. Act: The competent owners establish applicability and system boundary, then distinguish written scheme, examination findings and maintenance work. Hold / review: Keep affected operation held until required evidence, actions and operating acceptance are resolved; a document title alone is not release. Apply it: At which point would you hold this example, and what evidence would allow it to proceed? Load or attachment exceeds rated configuration: Collapse or dropped load can crush people below.

Defective lifting accessory: A sling or hook fails and the load swings or falls. Pressure system exceeds safe limit: Rupture or release causes blast, scald or toxic exposure. Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby? Eliminate: Avoid an unnecessary suspended lift or pressure-dependent step by redesigning flow or assembling at a safe accessible position. Reduce, including substitution: Choose a lifting or process method with suitable capacity and controlled interfaces for the actual load, radius, pressure and substance. Isolate: Provide designed physical safeguards: separation from suspended loads, suitable lifting installation and pressure-system protective devices. Control: Plan and supervise lifting to its complexity and define pressure-system operating limits and required written scheme/examination arrangements.

PPE: Select PPE for remaining handling, splash or other task exposure, checking fit and compatibility. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged. Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk? Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status. Apply it: Which official source and full-topic section will you use to resolve the next decision?

Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links. Confirm the equipment is the right type for the task, check guards and controls, inspect for obvious damage, understand the safe method and emergency response, keep others clear, and stop if condition or permission is uncertain. Confirm the equipment is the right type for the task, check guards and controls, inspect for obvious damage, understand the safe method and emergency response, keep others clear, and stop if condition or permission is uncertain. A machine, lifting device or pressure system may have overlapping duties, but a single certificate does not close every risk.

Apply it: Which part of this plan would you check at the workface before authorising the task? Use the evidence to improve the actual work arrangement. A machine, lifting device or pressure system may have overlapping duties, but a single certificate does not close every risk. Identify the actual task and equipment, apply the workplace-use rules, then test whether lifting or qualifying pressure-system duties add planning, examination, written-scheme and competent-person requirements. Authorisation, pre-use check, task briefing, any defect report and supervisor release. Apply it: What evidence would show that the change improves this task, rather than only completing a record? Fictional example: a practical application of the existing topic lesson. Setting: A fictional workshop receives an identified air-receiver system with connected pipework and protective devices.

Act: The competent owners establish applicability and system boundary, then distinguish written scheme, examination findings and maintenance work. Hold / review: Keep affected operation held until required evidence, actions and operating acceptance are resolved; a document title alone is not release. Apply it: At which point would you hold this example, and what evidence would allow it to proceed? Connect the task, the route to the person and the control that can fail. Load or attachment exceeds rated configuration: Collapse or dropped load can crush people below. Defective lifting accessory: A sling or hook fails and the load swings or falls. Pressure system exceeds safe limit: Rupture or release causes blast, scald or toxic exposure.

Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby? Control summary. Read the complete task-specific controls and checks in the linked topic. Eliminate: Avoid an unnecessary suspended lift or pressure-dependent step by redesigning flow or assembling at a safe accessible position. Reduce, including substitution: Choose a lifting or process method with suitable capacity and controlled interfaces for the actual load, radius, pressure and substance. Isolate: Provide designed physical safeguards: separation from suspended loads, suitable lifting installation and pressure-system protective devices. Control: Plan and supervise lifting to its complexity and define pressure-system operating limits and required written scheme/examination arrangements. PPE: Select PPE for remaining handling, splash or other task exposure, checking fit and compatibility.

Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged. Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk? Follow the official sources below and retain the task-specific evidence. Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status. Apply it: Which official source and full-topic section will you use to resolve the next decision? Simplified learning guide.

Use the full topic and the actual work arrangements; existing technical-review and approval statuses still apply. Workplace scenarios labelled fictional are illustrative examples. Do not begin because the equipment ran yesterday, carries a conformity mark or belongs to a contractor. Check any recorded limitation, attachment, inspection status and local authorisation that the task actually requires. Identify equipment and task. During use: Use within assessed conditions.; At completion: Stop safely and leave controlled. Check guards, controls and condition. During use: Watch for change or defect.; At completion: Report defects and hand back. Confirm competence and area. During use: Keep others protected.; At completion: Record any hold or release.

Work equipment includes machinery, appliances, apparatus, tools and installations used at work, while use includes starting, stopping, programming, setting, transporting, repairing, modifying, maintaining, servicing and cleaning. A hand tool, office appliance, machine line, scaffold component, ladder, lift truck or process installation may be work equipment. The applicable controls depend on the actual use and risk, not the label or purchase value. Tool or appliance. Why it is in scope: Used to perform work.; Decision: Suitability and safe use. Machine or installation. Why it is in scope: Creates mechanical or other energy hazards.; Decision: Guarding, controls and lifecycle evidence. Cleaning or adjustment. Why it is in scope: It is use under Provision and Use of Work Equipment Regulations (PUWER).; Decision: Safe state and competent method.

Transport or modification. Why it is in scope: Can change condition or risk.; Decision: Planning, inspection and change control. PUWER controls equipment provided or used at work; product-supply rules govern placing products on a market. A CE, UK Conformity Assessed (UKCA) or CE and UK Northern Ireland (UKNI) route does not by itself prove workplace suitability, correct installation or safe use. Choose the GB or NI market route and the product sector before relying on conformity documentation. Separately complete workplace selection, risk assessment, guarding, installation, competence, inspection and maintenance decisions. Who will use it and for what? Workplace-use route: PUWER and other workplace law.; Product-supply route: Not the main market decision. May this product be placed on this market?

Workplace-use route: Does not answer safe-use question.; Product-supply route: Current GB or NI sector rules. Was it modified or assembled? Workplace-use route: Reassess safe use.; Product-supply route: May create manufacturer obligations. Sources: HSE INDG229 Using work equipment safely; HSE PUWER guidance and topic index; Provision and Use of Work Equipment Regulations 1998; Provision and Use of Work Equipment Regulations Northern Ireland 1999; HSE L22 Safe use of work equipment

How can lifting or pressure failures harm people?
How can lifting or pressure failures harm people?

Source: work-equipment-lifting-equipment-and-pressure-systems--harm-mechanisms

A failed sling or unstable lift can drop or swing a load into people; loss of containment can release hot, toxic or high-energy fluid. A shared piece of equipment can need separate safeguards and examinations for each failure pathway. Identify load path, lifting configuration, pressure source, safe limits, people exposed and the independent barriers. Hold the operation when a critical examination, written scheme or safe state is uncertain. Sources: HSE PUWER overview; HSE LOLER overview; HSE Pressure Systems Safety Regulations overview

How do PUWER, LOLER and pressure-system law fit together?

Source: work-equipment-lifting-equipment-and-pressure-systems--three-regime-decision

Use PUWER for the general safe-use duties of work equipment; add Lifting Operations and Lifting Equipment Regulations (LOLER) when the activity and equipment are within lifting law, and add Pressure Systems Safety Regulations (PSSR) where the pressure-system definition and application provisions are met. One asset can trigger more than one regime.

Source basis: Lifting Operations and Lifting Equipment Regulations 1998 · GOV.UK placing UKCA or CE marked products on the Great Britain market · Pressure Systems Safety Regulations 2000 · Provision and Use of Work Equipment Regulations 1998 · HSE GEIS6 MEWP selection management and use · HSE Inspection of work equipment · HSE L113 Safe use of lifting equipment · HSE L122 Safety of pressure systems · HSE LOLER overview · HSE Thorough examinations and inspections of lifting equipment · HSE Planning and organising lifting operations · Lifting Operations and Lifting Equipment Regulations Northern Ireland 1999 · GOV.UK placing CE or CE and UKNI marked products on the Northern Ireland market · Pressure Systems Safety Regulations Northern Ireland 2004 · Provision and Use of Work Equipment Regulations Northern Ireland 1999 · HSE Pressure Equipment Safety Regulations guidance · HSE Pressure Systems Safety Regulations overview · HSE Using pressure systems · HSE PUWER overview · HSE Work at height.

2 linked parts. Follow the question numbers and complete the applicable route.

Part 1 of 2 · Questions 1–3 Source basis: Lifting Operations and Lifting Equipment Regulations 1998 · Pressure Systems Safety Regulations 2000 · Provision and Use of Work Equipment Regulations 1998 · HSENI Work equipment and machinery guidance · HSE L113 Safe use of lifting equipment · HSE L122 Safety of pressure systems · HSE LOLER overview · HSE Planning and organising lifting operations · HSE Magnetic lifting devices · Lifting Operations and Lifting Equipment Regulations Northern Ireland 1999 · Pressure Systems Safety Regulations Northern Ireland 2004 · Provision and Use of Work Equipment Regulations Northern Ireland 1999 · HSE Pressure Equipment Safety Regulations guidance · HSE Pressure Systems Safety Regulations overview · HSE Using pressure systems · HSE PUWER overview · HSE Vacuum lifting equipment.

Do not infer that every pressure vessel needs a written scheme or that every vertical movement is LOLER lifting. Decide jurisdiction, equipment identity, use, relevant fluid, load and exceptions with competent evidence before choosing the route. Product-supply law is a separate question. Sources: HSE PUWER overview; Provision and Use of Work Equipment Regulations 1998; Provision and Use of Work Equipment Regulations Northern Ireland 1999; Lifting Operations and Lifting Equipment Regulations 1998; Lifting Operations and Lifting Equipment Regulations Northern Ireland 1999

How can the ISO 45001 hierarchy of controls reduce equipment, lifting and pressure-system risks?

Source: work-equipment-lifting-equipment-and-pressure-systems--control-priorities

Remove the hazard where reasonably practicable. If it remains, consider a safer method, engineering controls and safe work arrangements before personal protective equipment for residual risk. HSE places elimination, substitution, engineering, administrative controls and personal protective equipment in that order. Verify that the chosen controls work on the actual task. ERICPD (Eliminate, Reduce including substitution, Isolate, Control, personal protective equipment (PPE), Discipline) is a SHARE decision prompt cross-mapped to HSE’s five-level hierarchy. Choose stronger feasible controls first, verify them in the actual task and record why a stronger option cannot be used. Discipline means sustaining controls through maintenance, supervision and learning. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering.

Discipline verifies and sustains every control level. The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation"). ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance. Sources: HSE hierarchy of control

What makes an activity a lifting operation?

Source: work-equipment-lifting-equipment-and-pressure-systems--lifting-scope

A lifting operation is concerned with lifting or lowering a load, including a person; determine whether the equipment and activity fall under the applicable GB or NI LOLER regime before using a lifting checklist. A mobile elevating work platform (MEWP) is one example whose actual lifting function and use need a competent scope decision. Conveyors, escalators, simple pallet trucks that only raise enough for travel, and public-use equipment can have different routes. A MEWP, hoist, crane, sling, lift truck or lifting attachment needs a task-specific decision. Do not equate any upward motion with LOLER. Crane or hoist. Question: What load and lift path?; Next step: LOLER and PUWER assessment. MEWP or people carrier.

Question: Are people lifted and what other height duties apply?; Next step: Specialist competent route. Conveyor or simple pallet truck. Question: Is this lifting within LOLER meaning?; Next step: Verify applicability; PUWER may still apply. Select equipment and accessories for the actual load, configuration, environment and failure modes; check marked safe working load and applicable configuration information before the lift. Capacity alone is not compatibility. Check the load mass and centre of gravity, attachment method, travel path, support and ground, foreseeable dynamic effects, people nearby and manufacturer limits. A magnet or vacuum attachment needs material and surface compatibility, not merely a matching mass.

Sources: HSE LOLER overview; Lifting Operations and Lifting Equipment Regulations 1998; Lifting Operations and Lifting Equipment Regulations Northern Ireland 1999; HSE L113 Safe use of lifting equipment; HSENI Work equipment and machinery guidance

Who plans and supervises lifting operations?
Who plans and supervises lifting operations?

Source: work-equipment-lifting-equipment-and-pressure-systems--lifting-plan

Every lifting operation involving lifting equipment must be properly planned by a competent person, appropriately supervised and carried out safely, with the depth of the plan proportionate to the foreseeable risk. Source basis: HSE Work equipment and machinery FAQs · Lifting Operations and Lifting Equipment Regulations 1998 · HSE GEIS6 MEWP selection management and use · HSENI Work equipment and machinery guidance · HSE Inspection of work equipment · HSE L113 Safe use of lifting equipment · HSE LOLER overview · HSE Thorough examinations and inspections of lifting equipment · HSE Planning and organising lifting operations · HSE Maintenance of work equipment · Lifting Operations and Lifting Equipment Regulations Northern Ireland 1999 · HSE Work at height.

Simple repeated work may use a suitable standing plan; unusual, complex or changed lifts need a specific competent review. Set roles, communication, load attachment, travel, exclusion, weather, ground and contingency before starting. A template alone is not a completed plan. Lifting people requires equipment and arrangements suitable for that purpose, with additional safeguards, escape and rescue decisions and thorough-examination requirements under the applicable lifting regime. Do not use a goods-only lifting device to carry people without a lawful and competent equipment-specific route. Confirm carrier, controls, fall and crushing risks, communication, rescue, capacity and the separate work-at-height or care-setting requirements where relevant. Is the carrier designed for people? Evidence: Manufacturer purpose and marking.; Stop: Goods-only or uncertain. Can people be protected and rescued?

Evidence: Task plan and emergency method.; Stop: Rescue not available. Is statutory examination current? Evidence: Competent report or scheme.; Stop: Missing or adverse report. Before lifting, identify equipment and load, check accessories and attachment, confirm the current plan and applicable examination evidence, inspect for visible defects, clear the route and verify people, ground, signals and stop arrangements. A pre-use check does not replace thorough examination, nor does an examination report replace the user check. Conditions may change after either record was made. Identity, markings, visible condition and report. During: Keep within assessed route and configuration.; After: Set down safely and inspect. Load, attachment, people, ground and signals. During: Stop for drift, alarm or change.; After: Record defects and handover.

Sources: HSE Planning and organising lifting operations; Lifting Operations and Lifting Equipment Regulations 1998; Lifting Operations and Lifting Equipment Regulations Northern Ireland 1999; HSE L113 Safe use of lifting equipment; HSE LOLER overview

How is LOLER thorough examination different from inspection?

Source: work-equipment-lifting-equipment-and-pressure-systems--lifting-examination

A LOLER thorough examination is a competent person's systematic, detailed assessment with a written report under the applicable law or competent examination scheme; a user check, PUWER inspection and maintenance are separate controls. The applicable law or scheme determines the examination timing and scope. Initial installation, reassembly, deterioration and exceptional events may trigger examination. Do not publish a universal site interval, use an old sticker alone, or treat routine overload testing as automatic. See HSE Thorough examinations and inspections of lifting equipment. A dangerous or potentially dangerous finding must be communicated and acted on through the applicable reporting route; withdraw equipment from use as required, control the area and use the competent report to decide repair, re-examination and release.

Do not treat a passed sticker, a maintenance action or production pressure as authority to override the report. The competent examiner and dutyholder have distinct reporting responsibilities; the exact statutory route depends on GB or NI law and the finding. Dangerous defect. Immediate action: Stop and prevent use.; Evidence: Report, quarantine and notification. Time-limited defect. Immediate action: Meet the report requirement or stop use.; Evidence: Action owner and deadline. Repair complete. Immediate action: Obtain required verification before use.; Evidence: Technical evidence and named release. The receiving organisation must verify equipment identity, suitability, condition, instructions and required examination evidence before use, while supplier, hirer and site owners coordinate their distinct duties. Reassembly at a new site or an exceptional event can trigger further examination.

Transfer records should follow the equipment; a delivery note is not a lift plan or proof of safe assembly. Supplier to hirer. Check: Identity, instructions, condition and reports.; Hold: Missing or mismatched evidence. Site assembly. Check: Competent installation and examination trigger.; Hold: Unverified assembly. Site to operator. Check: Task plan, competence, site limits and defects.; Hold: Unbriefed operator or changed site.

Sources: HSE Thorough examinations and inspections of lifting equipment; HSE L113 Safe use of lifting equipment; HSE Inspection of work equipment; HSE Maintenance of work equipment; Lifting Operations and Lifting Equipment Regulations 1998 For GB LOLER, unless a competent examination scheme specifies another interval, the usual periodic categories are six months for equipment lifting people and lifting accessories, and twelve months for other lifting equipment. Initial-use evidence, installation or reassembly and exceptional events need separate checks; a current periodic date does not cancel those triggers. The competent examiner determines the actual scheme and report requirements. Use the separate NI LOLER instrument and HSENI route for NI equipment, rather than transplanting this GB summary.

When does pressure-system law apply?

Source: work-equipment-lifting-equipment-and-pressure-systems--pressure-scope

Determine whether the system, relevant fluid and exclusions fall under GB PSSR 2000 or NI PSSR 2004 before deciding on safe limits, a written scheme and examination. Steam, compressed gas and some hot-water systems may be within scope, but applicability is not decided by a pressure gauge alone. Hydraulic oil systems can still be dangerous and require PUWER or other controls even when outside PSSR. Map vessel, pipework, pipeline, protective devices and fluid with competent advice. The user or owner must have safe operating limits established from competent system-specific evidence and operate within them; the page cannot set a pressure, temperature, flow or relief-device value. Check every component and protective device, including the weakest boundary, changed duty and repair history.

Manufacturer information and competent assessment control the actual limits. Ensure operators can see and act on them. Limits established. Evidence: Design and manufacturer data plus competent system assessment.; Stop: Unknown or conflicting limit. Protection suitable. Evidence: Verified device selection, setting and discharge route.; Stop: Defeated or uncertain protection. Operation within limits. Evidence: Readable indication and response.; Stop: Excursion or unreliable reading. Sources: HSE Pressure Systems Safety Regulations overview; HSE Using pressure systems; HSE L122 Safety of pressure systems; Pressure Systems Safety Regulations 2000; Pressure Systems Safety Regulations Northern Ireland 2004 HSE identifies steam at any pressure, compressed or liquefied gas above 0.5 bar gauge, pressurised hot water above 110 °C and gas dissolved under pressure as relevant-fluid categories. These are applicability clues, not operating limits.

Map the system and exceptions with the competent person. Under GB PSSR the installed-system user and mobile-system owner have distinct dutyholder routes; hired equipment still needs verified scheme and examination evidence. Apply the separate NI PSSR 2004 route in Northern Ireland.

What is a written scheme of examination?
What is a written scheme of examination?

Source: work-equipment-lifting-equipment-and-pressure-systems--pressure-written-scheme

For a qualifying pressure system, the user or owner must have a suitable written scheme before operation; a competent person draws it up or certifies it, and it identifies covered parts, examination methods, intervals and preparation for safe examination. Before first use of a qualifying system, the written scheme must be in place and the required examination undertaken; keep the system out of use until both are satisfied. Source basis: Pressure Systems Safety Regulations 2000 · HSENI L122 approved for use in Northern Ireland · HSE L122 Safety of pressure systems · HSE Maintenance of work equipment · Pressure Systems Safety Regulations Northern Ireland 2004 · HSE Pressure Systems Safety Regulations overview · HSE Using pressure systems.

The scheme must cover protective devices and relevant vessels or pipework whose failure could cause danger, subject to the applicable legal text and competent scope decision. It is not a maintenance schedule, a generic certificate or proof that an examination has happened. See HSE L122 Safety of pressure systems. The system parts in the written scheme must be examined by a competent person in accordance with that scheme, with reports and actions that show whether continued use is safe. The competent person needs suitable knowledge, resources, independence and authority for the actual system. Examination does not replace operator checks, maintenance, safe limits, protective devices or correct repair. Do not infer intervals from a generic boiler or compressor example.

Sources: HSE L122 Safety of pressure systems; HSE Pressure Systems Safety Regulations overview; Pressure Systems Safety Regulations 2000; Pressure Systems Safety Regulations Northern Ireland 2004; HSENI L122 approved for use in Northern Ireland

How are pressure systems operated and maintained?

Source: work-equipment-lifting-equipment-and-pressure-systems--pressure-operation

Operate within established safe limits using effective protective devices, competent people, clear instructions and a whole-system maintenance plan; isolate and depressurise safely before intervention. Pressure-system examination and maintenance are different. Include corrosion, leakage, alarms, relief devices, connections, pipework, environment, change and operator handover. A pressure indication of zero at one point is not proof that all stored energy is controlled. Start and run. Control: Limits, protection and competent operation.; Stop: Unreliable reading or excursion. Maintain. Control: Isolation, depressurisation, verification and safe access.; Stop: Trapped pressure or unknown connection. Handover. Control: Condition, defects and outstanding actions.; Stop: Unclear plant state.

Hold the affected system, assess the change against design and safe limits, update the written scheme when required, obtain competent examination where the scheme or law requires it, and release only after controlled testing and named acceptance. Repairs, replacement components, changed fluids and operating conditions can alter the pressure boundary. A maintenance completion or leak test alone is not statutory examination or authority to operate. Repair or replacement. Check: Material, design, protective devices and required examination.; Release condition: Competent evidence accepted. Changed duty. Check: Safe limits, scheme scope and instructions.; Release condition: Updated and approved basis. Commissioning test. Check: Controlled plan, exclusions and stop triggers.; Release condition: Documented operating handback.

Move people clear, raise the alarm, follow the site emergency plan and keep the system isolated from further operation; do not approach a leak, adjust a relief device or reopen a vessel until the hazard and safe state are established by authorised people. Treat vessel, line and connected process as potentially energised. Investigate cause and affected scope, protect others, obtain any required competent examination and controlled test, then require named operating acceptance. Leak or unusual sound. Immediate action: Withdraw and warn.; Restart barrier: No approach until assessed. Relief device operates. Immediate action: Escalate and preserve evidence.; Restart barrier: No reset-only return. Rupture or injury. Immediate action: Emergency response and exclusion.; Restart barrier: Investigation and competent release.

Sources: HSE Using pressure systems; HSE L122 Safety of pressure systems; HSE Maintenance of work equipment; Pressure Systems Safety Regulations 2000; Pressure Systems Safety Regulations Northern Ireland 2004

Can one inspection or certificate cover every duty?

Source: work-equipment-lifting-equipment-and-pressure-systems--examination-comparison

No. Keep a distinct evidence route for PUWER inspection, LOLER thorough examination, pressure written-scheme examination, maintenance, pre-use checks and product conformity; only a competent, lawful decision can determine any overlap. A contractor or insurer may supply a report, but the dutyholder must verify scope, findings, equipment identity and actions. A clear matrix prevents an in-date document for one duty being mistaken for another. Assess every relevant regime and the shared failure path, such as a pressure-powered lifting device, a pressurised attachment or a lift near a pressure vessel; coordinate the plant owners before work. A lifting plan cannot certify a pressure boundary, and a pressure written scheme cannot approve a suspended-load route.

Map energy, load, people, structures and simultaneous work, then hold until each competent decision and handover is complete. Pressure-powered lifting device. Combined question: Which components trigger LOLER and PSSR, if any?; Evidence: Two applicability decisions and integrated controls. Lift over pressure plant. Combined question: Could impact or collapse compromise pressure containment?; Evidence: Lift path and protection plan. Shared maintenance. Combined question: Who controls load, pressure and isolation?; Evidence: Joint permit, verification and handback. Sources: HSE Inspection of work equipment; HSE Thorough examinations and inspections of lifting equipment; HSE L122 Safety of pressure systems; HSE Pressure Equipment Safety Regulations guidance; GOV.UK placing UKCA or CE marked products on the Great Britain market

How do lifting and pressure controls change across settings?
How do lifting and pressure controls change across settings?

Source: work-equipment-lifting-equipment-and-pressure-systems--sector-transfer

A warehouse lift, patient hoist, construction crane and industrial boiler have different loads, people and technical limits. Apply the appropriate GB or NI workplace, lifting and pressure routes to the actual activity. A six-month or twelve-month shorthand does not replace the correct examination scheme or competent judgement. Check who owns the equipment and who has authority to stop use. Sources: HSE LOLER overview; HSE Pressure Systems Safety Regulations overview; HSENI Work equipment and machinery guidance; HSE GEIS6 MEWP selection management and use

Which Great Britain law applies to these decisions?

Source: work-equipment-lifting-equipment-and-pressure-systems--legal-gb-combined

In Great Britain, PUWER 1998 provides the work-equipment baseline, LOLER 1998 adds lifting duties, and PSSR 2000 adds pressure-system duties where each applies; HSWA and Management Regulations support risk assessment and safe systems. Use current amended legal text and HSE guidance. L22, L113 and L122 are Approved Code of Practice (ACOP) and guidance with specific status; product-supply regimes are separate. Applicability and exceptions require a competent review. See Provision and Use of Work Equipment Regulations 1998. Sources: Provision and Use of Work Equipment Regulations 1998; Lifting Operations and Lifting Equipment Regulations 1998; Pressure Systems Safety Regulations 2000; HSE L22 Safe use of work equipment; HSE L113 Safe use of lifting equipment

Which Northern Ireland law applies to these decisions?

Source: work-equipment-lifting-equipment-and-pressure-systems--legal-ni-combined

In Northern Ireland, PUWER NI 1999, LOLER NI 1999 and PSSR NI 2004 are separate legal routes; HSENI approves L122 for use with NI pressure-system law, while product-supply questions must follow the applicable NI market rules. Do not label the GB regulations as UK-wide. Check current NI legal effects and HSENI guidance, identify the actual system and operation, and seek competent NI advice before operational use. See Provision and Use of Work Equipment Regulations Northern Ireland 1999. Sources: Provision and Use of Work Equipment Regulations Northern Ireland 1999; Lifting Operations and Lifting Equipment Regulations Northern Ireland 1999; Pressure Systems Safety Regulations Northern Ireland 2004; HSENI L122 approved for use in Northern Ireland; HSENI Work equipment and machinery guidance

How should management arrangements be checked?

Source: work-equipment-lifting-equipment-and-pressure-systems--standards-boundaries

Assign responsibility, assess the actual risk, implement controls, monitor whether they work and review after change or failure. HSE’s Plan, Do, Check, Act guidance supports management review. It does not replace topic-specific law, technical assessment or competent sign-off. Sources: HSE Managing for health and safety (HSG65)

How should work equipment be controlled across its life?

Source: work-equipment-lifting-equipment-and-pressure-systems--lifecycle

Control starts with need and specification, continues through purchase or hire, acceptance, installation, use, inspection, maintenance and change, and ends with safe decommissioning or disposal. Treat each transfer as an evidence gate. A check at purchase does not cover later deterioration, modification, relocation, new attachments, changed users or a different environment. Select. Critical question: Is this the right equipment and control concept?; Evidence: Specification and risk decision. Accept and install. Critical question: Is identity, condition and setup proven?; Evidence: Acceptance and commissioning. Use and maintain. Critical question: Does it remain safe in real work?; Evidence: Checks, defects, maintenance and inspection. Change or retire. Critical question: Has risk changed or energy been removed?; Evidence: Change review or decommission record.

Assess mechanical contact and ejection together with electrical, pressure, thermal, chemical, ergonomic, noise, vibration, fire, explosion, mobility, stability and work-at-height hazards that the equipment or task can create. Consider normal production, foreseeable abnormal events, clearing blockages, tool change, cleaning, testing, breakdown, maintenance and recovery after a stop. People nearby can be exposed even when they do not operate the equipment. Mechanical. Examples: Crushing, shearing, cutting, entanglement, drawing-in, ejection.; Control question: Can access or energy be prevented? Energy. Examples: Electricity, pressure, gravity, heat, stored motion.; Control question: Can every source be isolated and dissipated? Exposure. Examples: Dust, fume, noise, vibration, substances.; Control question: Which separate regime and source control apply? Context. Examples: Mobility, stability, falls, traffic, fire.; Control question: What environment and interface change the risk?

Select equipment that is suitable for the intended task, people, environment, loads and conditions, with risks controlled by design and compatible guards, controls, attachments and information. Prefer eliminating hazardous operations or choosing safer equipment before adding procedural controls. Include cleaning, maintenance, access, foreseeable misuse and emergency recovery in the selection decision. Task and capacity. Question: Can it do the work within maker limits?; Reject or hold when: Duty or attachment is unclear. People. Question: Can intended users operate and maintain it safely?; Reject or hold when: Access, reach or competence is unsuitable. Environment. Question: Is it suitable for wet, dusty, explosive or public conditions?; Reject or hold when: Protection or compatibility is unproven. Lifecycle.

Question: Can it be inspected, isolated and maintained?; Reject or hold when: Safe intervention cannot be achieved. A conformity mark supports the applicable product-supply process; it does not prove that equipment is suitable for a particular workplace, correctly installed, maintained, guarded for every task or safe after modification. In Great Britain, current guidance recognises UKCA and CE routes within their stated scope. In Northern Ireland, use the current CE or CE and UKNI route as applicable. Always check sector-specific rules and current dates. Declaration and marking. What it supports: Product-supply conformity route.; What it cannot replace: Task suitability and risk assessment. Instructions. What it supports: Intended use and residual risk information.; What it cannot replace: Safe local installation and supervision. Workplace acceptance.

What it supports: Condition and integration at the site.; What it cannot replace: Required ongoing maintenance and inspection. Verify identity, condition, documentation, correct market route where relevant, intended use, guards, controls, accessories, installation needs, inspection status and support before the equipment enters service. Record deviations and quarantine anything damaged, incomplete, unexpectedly modified or unsupported. Delivery paperwork alone is not a commissioning record. Identity and specification. Evidence: Model, serial or asset reference and intended duty.; Hold point: Mismatch or unknown origin. Condition and completeness. Evidence: Damage check, guards, accessories and instructions.; Hold point: Missing or damaged safety part. Legal and support route. Evidence: Applicable supplier documents and service support.; Hold point: Wrong market route or no critical information. Workplace readiness.

Evidence: Installation, risk assessment and training plan.; Hold point: Site prerequisites absent. Sources: HSE PUWER overview; HSE L22 Safe use of work equipment; HSE INDG291 Providing and using work equipment safely; Management of Health and Safety at Work Regulations 1999; Management of Health and Safety at Work Regulations Northern Ireland 2000

What belongs in a pre-use check?
What belongs in a pre-use check?

Source: work-equipment-lifting-equipment-and-pressure-systems--pre-use

A pre-use check should cover visible condition, correct setup and attachment, guards and protective devices, controls, cables or hoses, stability, work area and any equipment-specific indicator identified by the assessment or manufacturer. A quick user check is not a substitute for a formal inspection. Its content and record depend on risk, equipment and the organisation's system; do not invent a universal checklist or sign-off interval. Condition. Example observation: Damage, wear, leakage or loose part.; Action: Stop and report if safety may be affected. Safeguards. Example observation: Guard or device missing, open or defeated.; Action: Do not use; quarantine. Controls. Example observation: Start, stop or indication abnormal.; Action: Hold pending competent decision. Area and task.

Example observation: Wrong attachment, unstable base or people exposed.; Action: Correct conditions before start. Use equipment only for the assessed task and conditions, keep safeguards in place, maintain exclusion and stability, watch for abnormal sound, movement, heat, vibration, leakage or control response, and stop before investigating a change. Do not reach through a guard, defeat a device, clear a blockage live or rely on familiarity. A change in material, attachment, operator, environment or production method can invalidate the starting decision. Unexpected movement or ejection. Immediate response: Stop from a safe position.; Next decision: Quarantine and investigate. Guard or device changes state. Immediate response: Stop work and keep clear.; Next decision: Competent safeguarding review. Abnormal noise, heat or vibration.

Immediate response: Stop without close diagnosis.; Next decision: Maintenance assessment. Task or environment changes. Immediate response: Pause the job.; Next decision: Reassess method and suitability. Stop the equipment through the defined sequence, leave moving and stored energy controlled, clean without entering danger, record defects or restrictions, and hand back the equipment and area in a known state. Completion is not permission for maintenance. Any intervention requiring access to danger or stored energy needs its own isolation and authorised method. Normal stop. Expected state: Movement ceases through intended control.; Evidence: User observation. Secure and clean. Expected state: No unintended access, restart or unsafe residue.; Evidence: Task completion check. Report. Expected state: Defects and restrictions are visible to the next user.; Evidence: Tag, log or handover.

Hand back. Expected state: Named owner accepts status.; Evidence: Release or continued hold. Sources: HSE Inspection of work equipment; HSE INDG229 Using work equipment safely; HSE L22 Safe use of work equipment; HSE PUWER guidance and topic index; HSENI machinery safety devices safety alert

What is the guarding hierarchy?

Source: work-equipment-lifting-equipment-and-pressure-systems--guarding

Prevent access to dangerous parts with fixed guards where practicable, then use other guards or protection devices, then jigs, holders or push-sticks, with information, instruction, training, supervision and PPE only for remaining risk. A guard must be suitable, effective, maintained, not easily bypassed and not create a new hazard. Guard design and safe distance are equipment-specific engineering decisions, not values to copy from this guide. Protective devices must be selected for the risk, correctly installed, effective, maintained and used; a bypassed, defeated, poorly aligned or unreliable device is a stop and quarantine condition. Do not tape, wedge, bridge, override or programme around a device to maintain production. Diagnostic or test modes require a designed safe method, restricted authority and equipment-specific controls. Device functions normally.

Meaning: Only evidence for the tested safeguard function.; Response: Continue within assessed use. Intermittent trip. Meaning: Possible fault or changing condition.; Response: Stop, quarantine and diagnose safely. Bypass found. Meaning: Safeguard no longer reliable.; Response: Isolate as needed and escalate. Reset restores operation. Meaning: Does not explain cause.; Response: Investigate before release. Controls should be identifiable, appropriate, reachable from a safe position, protected against unintended operation where needed, and arranged so starting occurs only through deliberate action and stopping brings equipment to a safe state. The operator must understand normal stop, emergency response, reset and restart. A reset should not itself create hazardous movement unless the assessed control design specifically provides safe conditions. Start.

Expected behaviour: Deliberate action with danger zone clear.; Verification: Commissioning and user check. Normal stop. Expected behaviour: Brings operation to intended safe state.; Verification: Functional test. Mode or selector. Expected behaviour: Controls access and authority for the chosen mode.; Verification: Restricted setting and instruction. Restart. Expected behaviour: No unexpected movement after interruption or reset.; Verification: Cause and safe-state check. An emergency stop is additional rapid protection, not normal stopping or full isolation. After use, move clear, warn and report, exclude people and control connected equipment; do not reset, enter or investigate until authorised people apply equipment-specific energy isolation. The named operating owner releases only after cause, repair, safeguard and controlled-test evidence is accepted.

After use, keep people clear, establish the plant state and investigate the event. Releasing or resetting an emergency stop does not prove the machine is safe and must not by itself restart hazardous motion. When is it used? Answer: For an emergency requiring rapid stop.; Boundary: Not the routine production stop. What does it do? Answer: Acts with priority as designed.; Boundary: May not remove every energy source. Does it isolate? Answer: Not necessarily.; Boundary: Apply the full isolation procedure. Can it be reset and run? Answer: Only after cause and safe state are verified.; Boundary: Named return-to-service authority governs. Sources: HSE L22 Safe use of work equipment; HSE PUWER overview; HSENI machinery safety devices safety alert; HSE INDG291 Providing and using work equipment safely

How should equipment be isolated?
How should equipment be isolated?

Source: work-equipment-lifting-equipment-and-pressure-systems--isolation

Identify every energy source, stop and separate the equipment, prevent reconnection or release, dissipate or restrain stored energy, verify the safe state, control the work and restore only through the authorised sequence. Electrical isolation alone may leave hydraulic, pneumatic, pressure, thermal, gravity, spring, rotational or process energy. The actual isolation points, verification method and lock-off arrangements must come from competent equipment-specific planning. Plan maintenance as work in its own right: define scope, condition, isolation, access, competence, tools, parts, coordination, testing, safeguards and handback before intervention begins. Maintain equipment in an efficient state and good repair. Where maintenance cannot be done at rest, use an equipment-specific safe method and protection designed for that task; routine production pressure never supplies the justification. Prepare.

Control: Scope, hazards, safe state and people.; Evidence: Work order or task plan. Intervene. Control: Isolation, access, tools and coordination.; Evidence: Permit or maintenance record. Test. Control: Controlled test with restricted exposure.; Evidence: Functional and safeguard results. Hand back. Control: Covers, guards and settings restored.; Evidence: Named acceptance and release. Inspect after installation where safety depends on installation, after assembly at a new site where applicable, and at suitable risk-based intervals or after exceptional circumstances that may jeopardise safety. Frequency depends on the equipment, use, conditions, deterioration, manufacturer information and experience. This guide sets no blanket daily, weekly, annual or other interval. Installation or assembly. Purpose: Prove safe installation before use.; Decision basis: Equipment and installation dependency. Deterioration risk.

Purpose: Detect safety-relevant decline in time.; Decision basis: Risk, use, conditions and experience. Exceptional event. Purpose: Assess damage or loss of integrity.; Decision basis: Accident, modification, long disuse or severe condition. User check. Purpose: Identify obvious immediate defects.; Decision basis: Separate from formal inspection where required. Stop use where safety may be affected, bring the equipment to a controlled state, prevent further use, identify the defect, protect others, report it and keep it quarantined until competent evidence supports release. Do not remove a tag, swap a guard, clear a jam or press reset as an informal return to service. The severity, affected equipment and connected systems must be understood first. Immediate danger.

Action: Stop, keep clear and isolate if safe and trained.; Release condition: Emergency or competent recovery route. Safety device or guard defect. Action: Quarantine equipment.; Release condition: Repair and safeguarding verification. Condition uncertain. Action: Treat as held.; Release condition: Competent inspection and evidence. Minor non-safety issue. Action: Record and manage under local system.; Release condition: Decision still documented. Sources: HSE Maintenance of work equipment; HSE L22 Safe use of work equipment; HSE Electrical safety at work; HSE PUWER overview; HSE Inspection of work equipment

What must each role learn and demonstrate?

Source: work-equipment-lifting-equipment-and-pressure-systems--role-competence

Competence must match the decision and consequence of error. Attendance alone does not show that a worker, manager or specialist can recognise a stop condition, select a control and verify it in practice. Use observed tasks and scenario questions. Reassess after change, defect, incident or a materially different role, and seek a specialist for technical or legal decisions outside local competence. Sources: HSE Planning and organising lifting operations; HSE Thorough examinations and inspections of lifting equipment; HSE L122 Safety of pressure systems

How should modification and change be controlled?

Source: work-equipment-lifting-equipment-and-pressure-systems--modification-change

Keep modified, relocated, integrated or reprogrammed equipment out of normal work until the affected scope and product-supply duties are resolved, safeguards restored, applicable inspection or examination and controlled tests pass, and the named operating owner records release. A diagnostic or commissioning test under a separate controlled plan is not production permission. A change that appears to improve output can alter stability, access, stopping, control logic, load, exposure or maintenance. Keep the equipment held until technical, operational and legal boundaries are resolved. New attachment or duty. Workplace-use question: Is equipment still suitable and guarded?; Product-supply question: Does intended use or conformity scope change? Control or software change. Workplace-use question: Are modes, stops and restart safe?; Product-supply question: Who now takes manufacturer responsibility? Refurbishment.

Workplace-use question: Is condition and performance demonstrated?; Product-supply question: Is it substantially changed or newly supplied? Integration. Workplace-use question: Are whole-system risks controlled?; Product-supply question: Does an assembly become a new product? Users, supervisors and those who manage, inspect, maintain or modify equipment need adequate information, instruction and training for their role, with competence demonstrated for the actual equipment and task. Simple equipment may be covered by suitable in-house instruction; complex or high-risk work may need specialist training and supervised experience. There is no universal certificate or refresher expiry. User. Competence content: Normal use, checks, limits, defects and emergency response.; Review trigger: New equipment, task or performance concern. Supervisor. Competence content: Authorisation, observation, stop and release.; Review trigger: Change or control failure. Maintainer or inspector.

Competence content: Technical method, isolation and judgement.; Review trigger: Design change or scope extension. Manager or purchaser. Competence content: Suitability, interfaces and assurance.; Review trigger: New process, supplier or regime. Supervision should verify authorised people, correct equipment and setup, guards and controls, the actual method, conditions during use, defect response and handback, with closer oversight where competence or risk requires it. Supervision is an active control, not a signature. It should detect drift such as routine bypassing, wrong attachments, informal repairs, missed checks or production pressure overriding a hold. Start. Observation: Identity, setup, guards and people.; Response: Permit or hold. Work. Observation: Real behaviour and machine response.; Response: Coach, correct or stop. Change. Observation: New material, mode or environment.; Response: Pause and reassess. Finish.

Observation: Defects, state and handback.; Response: Release or quarantine. Hiring does not remove workplace-use duties: the supplier or hirer may have supply and maintenance obligations, while the employer or person controlling use must still ensure suitability, safe condition, inspection evidence, competence and safe operation. Agree in writing who selects, delivers, inspects, maintains, responds to defects and removes the equipment. Verify the agreement against what arrives and how it will actually be used. Supplier or hire company. Question: What is supplied, maintained and documented?; Evidence: Specification, instructions and inspection evidence. Hiring organisation. Question: Is it suitable for the actual workplace and task?; Evidence: Acceptance and risk assessment. User and supervisor. Question: Are setup, competence and daily condition controlled?; Evidence: Briefing, checks and defect route.

Breakdown or return. Question: Who makes safe and who authorises movement?; Evidence: Call-out, isolation and handover. The host and contractor should exchange task, site, equipment, competence, inspection, maintenance, isolation, emergency and defect information, then agree who controls each decision before work starts. A contractor-owned machine is not automatically acceptable, and a host permit does not prove its condition. Shared or connected systems need one coordinated safe state and clear release authority. Verify equipment and documents. During work: Coordinate exclusions and site conditions.; Handback: Report defects and restrictions. Agree isolation and emergency interfaces. During work: Stop on mismatch or unsafe change.; Handback: Jointly confirm equipment and area state. Name decision owners. During work: Protect other employers and the public.; Handback: Retain required evidence.

Sources: HSENI Refurbished and modified machinery; HSE Introduction to work equipment and machinery; GOV.UK placing UKCA or CE marked products on the Great Britain market; GOV.UK placing CE or CE and UKNI marked products on the Northern Ireland market; HSE Training and competence for work equipment

Which specialised regimes may also apply?
Which specialised regimes may also apply?

Source: work-equipment-lifting-equipment-and-pressure-systems--specialised-regimes

PUWER is not a complete answer where equipment lifts loads or people, contains pressure, uses electricity, supports work at height, creates substances, noise or vibration, or can ignite a dangerous atmosphere. Determine applicability for the real equipment and task in the correct jurisdiction. Sector regimes for construction, mines, quarries, agriculture, rail or merchant shipping may also change duties and enforcement routes. Lifting loads or people. Additional route: LOLER or NI equivalent as applicable.; Boundary: Separate thorough-examination and planning decisions. Pressure or electricity. Additional route: Pressure-systems or electrical-safety law.; Boundary: Specialist integrity and isolation. Work at height. Additional route: Work-at-height law.; Boundary: Access selection and fall prevention. Dust, fume, noise, vibration or flammables.

Additional route: COSHH, DSEAR, noise or vibration law.; Boundary: Separate exposure and ignition decisions. Raise the alarm, stop or isolate only through trained actions that are safe from the person's position, keep people out of danger, call the site emergency route and preserve the equipment state for competent recovery and investigation. Do not approach moving, energised, pressurised, hot, unstable or damaged equipment to diagnose it. Rescue, firefighting and first-aid actions must follow the site plan and trained roles. Person in danger. Immediate action: Raise alarm and use designed emergency control if safe.; Prohibited assumption: Do not enter the danger zone. Unexpected movement or release. Immediate action: Keep clear and stop connected work.; Prohibited assumption: Emergency stop is not full isolation. Fire, pressure or electrical event.

Immediate action: Use the site emergency plan.; Prohibited assumption: Do not improvise specialist response. After the event. Immediate action: Maintain exclusion and control evidence.; Prohibited assumption: No restart because conditions appear normal. The named operating owner should authorise return only after the cause is understood, repairs and safeguards are complete, inspection or testing matches the defect and risk, people are clear, documentation is updated and restrictions are communicated. Repair completion, a reset, a replaced fuse, an inspection sticker or production need is not enough by itself. Serious events or modifications may require engineering, safeguarding, electrical, pressure, lifting or legal review. Cause. Required evidence: Defect or event understood.; Owner: Competent investigator or specialist. Restoration. Required evidence: Repair and safeguards verified.; Owner: Maintainer and tester. Readiness.

Required evidence: Method, competence, area and interfaces ready.; Owner: Supervisor and affected parties. Authorisation. Required evidence: Signed or recorded release.; Owner: Named operating owner. Sources: HSE LOLER overview; HSE Pressure systems; HSE Electrical safety at work; HSE Work at height; HSE Dangerous substances and explosive atmospheres

Who owns each work-equipment decision?

Source: work-equipment-lifting-equipment-and-pressure-systems--roles

Assign owners for specification, acceptance, use, inspection, maintenance, isolation, modification, quarantine, emergency control and return to service; do not let responsibility disappear between departments or companies. One person may hold several roles, but the evidence and competence requirements remain distinct. Emergency command and later operational release are separate decisions. Specification and acceptance. Typical owner: Purchaser and technical owner.; Interface: User and maintenance input. Use and supervision. Typical owner: Operating manager or supervisor.; Interface: Worker and nearby people. Inspection and maintenance. Typical owner: Competent person and asset owner.; Interface: Defect and isolation system. Return to service. Typical owner: Named operating owner.; Interface: Technical evidence and affected parties.

Sources: HSE PUWER overview; HSE Work equipment and machinery FAQs; Management of Health and Safety at Work Regulations 1999; Management of Health and Safety at Work Regulations Northern Ireland 2000

How should work-equipment control be assured?

Source: work-equipment-lifting-equipment-and-pressure-systems--assurance

Assurance should test whether equipment is suitable, safeguards work, defects are controlled, inspections and maintenance match risk, competence is real, contractor interfaces work and return-to-service decisions are evidence based. Use field observation and equipment sampling, not record presence alone. Trend repeated guard damage, bypasses, emergency stops, overdue actions, recurring faults and differences between shifts or sites. Is the inventory complete? Evidence: Assets, location, owner and status.; Escalation: Unknown equipment held. Do safeguards work in practice? Evidence: Observed use and functional evidence.; Escalation: Bypass or drift quarantined. Are defects closed? Evidence: Traceable report, repair and release.; Escalation: Repeat or overdue issue reviewed. Are people competent? Evidence: Demonstration and supervision.; Escalation: Restriction or refresher based on need.

Missing or defeated guards, unexpected movement, unreliable controls, recurring trips, damaged cables or hoses, leaks, unstable equipment, unknown modifications, expired required evidence or informal repairs require a stop, hold or competent review. Also treat emergency-stop use, reports that workers must reach into danger, and workarounds that have become normal as control failures rather than operator inconvenience. Guard opened or removed for production. Likely weakness: Safeguarding and workflow conflict.; Action: Stop and redesign or restore. Frequent reset or emergency stop. Likely weakness: Unresolved fault or process instability.; Action: Quarantine and investigate. Temporary tape, wedge or bridge. Likely weakness: Device defeated.; Action: Prevent use and escalate. Inspection or modification unclear. Likely weakness: Evidence gap.; Action: Hold pending competent decision.

Sources: HSE Inspection of work equipment; HSE Training and competence for work equipment; HSE L22 Safe use of work equipment; HSENI machinery safety devices safety alert; HSE INDG229 Using work equipment safely

What do complete work-equipment decisions look like?

Source: work-equipment-lifting-equipment-and-pressure-systems--operational-examples

Four complete fictional BuildOut Ltd cases cover routine guarded-drill work, hired mobile equipment, an overhead-hoist evidence mismatch and a changed compressed-air system. The four scenario-type summaries are decision prompts, not ten worked cases. Actual equipment, jurisdiction, examination evidence and named authorisation govern. BuildOut Ltd could use one asset lifecycle with risk-based gates for specification, acceptance, authorisation, use, defects, maintenance, inspection, change and release, while applying the correct GB or NI and specialist regime at each site. The fictional model keeps operations, engineering, procurement and contractors connected. It does not replace equipment-specific instructions, examinations, limits or site authority. Specify. BuildOut owner: Procurement plus technical and user leads.; Minimum evidence: Task, environment and safeguard requirements. Accept.

BuildOut owner: Asset owner and competent installer.; Minimum evidence: Identity, condition, documentation and commissioning. Operate. BuildOut owner: Supervisor and authorised user.; Minimum evidence: Checks, competence and method. Hold and release. BuildOut owner: Operating owner with technical evidence.; Minimum evidence: Defect closure and recorded authorisation. Each example is a training pattern, not an equipment permission. Replace every fictional detail with the real machine, manufacturer instructions, energy sources, people, environment, inspection status and named authority.

Sources: HSE PUWER overview; Management of Health and Safety at Work Regulations 1999; Management of Health and Safety at Work Regulations Northern Ireland 2000; HSE PUWER guidance and topic index; HSE Inspection of work equipment The previously advertised hired-MEWP report mismatch and unexpected autoclave vent remain useful discussion prompts, rather than completed additional cases here. A report mismatch holds the equipment pending identity/scope resolution; an unexpected vent requires the site’s safe stop or emergency route and competent pressure-system investigation before a separately authorised return. General guarding, maintenance, unknown modification and emergency-stop interfaces remain in the existing scenario summaries and main guidance; none supplies permission for the actual equipment.

Acronyms and terms
Acronyms and terms

Source: work-equipment-lifting-equipment-and-pressure-systems--terms

Keep work equipment, use, guard, protection device, emergency stop, isolation, inspection, maintenance, competent person, quarantine and return to service distinct. Sources: Provision and Use of Work Equipment Regulations 1998; Provision and Use of Work Equipment Regulations Northern Ireland 1999; HSE L22 Safe use of work equipment

Routine guarded pillar-drill task

Source: work-equipment-lifting-equipment-and-pressure-systems--example--routine-guarded-drill

Task Material And Setting: Fictional training only, not authorisation for a real drill. An authorised user checks the task, material, workholding, guard, controls and area before use. Stop and hold for a loose workpiece, damaged bit, guard or control defect, unusual response or intrusion; never adjust while moving. Use the normal stop, wait for movement to cease and record defects. The workshop supervisor accepts the pre-use, briefing, defect-closure and safe handback evidence before release under the applicable GB or NI PUWER route. People And Prerequisites: Authorised user and workshop supervisor; suitable drill, correct workholding and bit, current local assessment, functioning guard and controls, safe area and known defect route.

Before: Confirm the task and material, inspect the drill, guard, workholding and emergency control, remove loose items, set the work securely and keep others outside the operating space. During: Keep the guard and workholding in position, use the intended controls, observe sound, movement and swarf, and stop before any adjustment or clearing. Hold Or Stop: Do not start or continue for a loose workpiece, damaged bit, missing or defeated guard, unreliable control, unusual movement, unexpected material response or unauthorised person in the area. Completion And Hand Back: Stop through the normal control, wait for movement to cease, leave the machine and area clean through the safe method, record any defect and hand back in a known state.

Evidence: Authorisation, pre-use check, task briefing, any defect report and supervisor release. Source boundary: Fictional training only, not equipment permission. Apply the actual GB or NI PUWER, LOLER or PSSR route as appropriate, with task-specific manufacturer information, competent assessment, evidence and named release.

Hired mobile equipment arrives on site

Source: work-equipment-lifting-equipment-and-pressure-systems--example--hired-mobile-platform

Task Material And Setting: Fictional training only, not permission to operate hired plant. Keep the platform out of service while identity, condition, instructions, applicable PUWER inspection and LOLER examination evidence, ground, route, weather, rescue plan and competence are checked. Reject or quarantine any mismatch or uncertainty; obtain supplier and competent site clarification. The site supervisor accepts use only on the actual evidence and records defects and return handover. People And Prerequisites: Hire supplier, site logistics lead, competent equipment assessor, authorised operator and supervisor; agreed specification, delivery evidence, site assessment, ground and route plan, rescue and defect arrangements, and any specialised examination evidence required.

Before: Match the delivered machine to the order, inspect condition and documentation, verify inspection or examination evidence applicable to the machine, confirm ground, access, weather and interface controls, and brief the authorised operator. During: Use only within manufacturer and site limits, maintain route and people controls, observe stability and machine response, and stop for changed ground, weather, load, alarm or condition. Hold Or Stop: Reject or quarantine the equipment for identity mismatch, damage, missing safety information, uncertain inspection or examination status, wrong attachment, unsuitable ground, unavailable rescue arrangements or unverified operator competence. Completion And Hand Back: Park and secure through the agreed method, record condition and defects, prevent further use where held, and complete a joint handover to the supplier or site owner.

Evidence: Hire specification, delivery and acceptance record, applicable inspection or examination evidence, operator authorisation, daily checks, defect history and return handover. Source boundary: Fictional training only, not equipment permission. Apply the actual GB or NI PUWER, LOLER or PSSR route as appropriate, with task-specific manufacturer information, competent assessment, evidence and named release.

Overhead hoist: accessory identity does not match the report

Source: work-equipment-lifting-equipment-and-pressure-systems--example--overhead-hoist-evidence

Task Material And Setting: Fictional workshop lift of a fabricated frame. The planned sling identity differs from the available examination report; no load is lifted. People And Prerequisites: Lifting planner, competent examiner and operating owner; actual load/configuration, suitable equipment, lift plan and applicable GB or NI examination route. Before: Match hoist and accessory identities, capacity/configuration and required reports to the planned lift; check site conditions and operator competence. During: Keep the lift on hold while the supplier and competent examiner resolve the mismatch. Do not trial the lift to prove the sling is sound. Hold Or Stop: Missing identity, scope mismatch, unresolved defect or changed configuration prevents lifting.

Completion And Hand Back: The operating owner releases only after matching accepted evidence, any required examination/defect closure, a checked lift plan and team briefing. Evidence: Asset/accessory identities, relevant examination report, defect disposition, plan and named release record. Source boundary: Fictional teaching application of the cited regulator guidance; actual equipment, jurisdiction, competent examination and authorisation govern. Not a work instruction.

Changed compressed-air system: scheme coverage unresolved

Source: work-equipment-lifting-equipment-and-pressure-systems--example--changed-air-system

Task Material And Setting: Fictional installed compressed-air receiver with changed connected pipework and protection. The existing written scheme has not been confirmed to cover the changed system; pressure operation is held. People And Prerequisites: Installed-system user, competent pressure-system person and authorised engineering team; fluid, boundary, modifications and applicable GB or NI PSSR scope established. Before: Compare actual system identity, relevant fluid, protective devices and change record with safe-limit and scheme documentation. During: Keep pressure operation prohibited while the competent person reviews scheme coverage, examination needs and protection evidence. Control maintenance energy through the approved system-specific method. Hold Or Stop: Unknown scope, absent required scheme/examination evidence, unresolved protection or limits prevents use; no generic pressure setting is supplied.

Completion And Hand Back: The responsible user authorises operation only after accepted safe-limit evidence, a suitable written scheme, required completed examination, closed defects and operator briefing. Evidence: System boundary/change record, scheme version, examination findings, protection verification, instructions and named user release. Source boundary: Fictional teaching application of the cited regulator guidance; actual equipment, jurisdiction, competent examination and authorisation govern. Not a work instruction.

Source tables and records 1
How can lifting or pressure failures harm people? decision table

Table ID: work-equipment-lifting-equipment-and-pressure-systems-harm-mechanisms

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html

Row 1

Column 1

Load or attachment exceeds rated configuration

Column 2

Collapse or dropped load can crush people below.

Column 3

Use a planned lift, marked safe working load and verified configuration; stop when rating or ground is uncertain.

Row 2

Column 1

Defective lifting accessory

Column 2

A sling or hook fails and the load swings or falls.

Column 3

Pre-use check plus competent thorough examination; withdraw a dangerous defect.

Row 3

Column 1

Pressure system exceeds safe limit

Column 2

Rupture or release causes blast, scald or toxic exposure.

Column 3

Defined safe limits, protective devices and written-scheme examination; isolate on abnormal pressure.

Read the complete comparison table
How can lifting or pressure failures harm people? decision table
RowColumn 1Column 2Column 3
1Load or attachment exceeds rated configurationCollapse or dropped load can crush people below.Use a planned lift, marked safe working load and verified configuration; stop when rating or ground is uncertain.
2Defective lifting accessoryA sling or hook fails and the load swings or falls.Pre-use check plus competent thorough examination; withdraw a dangerous defect.
3Pressure system exceeds safe limitRupture or release causes blast, scald or toxic exposure.Defined safe limits, protective devices and written-scheme examination; isolate on abnormal pressure.
How do PUWER, LOLER and pressure-system law fit together?

Table ID: work-equipment-lifting-equipment-and-pressure-systems-three-regime-decision-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html Scope: Great Britain|Northern Ireland: How do PUWER, LOLER and pressure-system law fit together?. Decide actual equipment, operating or intervention mode, load/configuration or relevant fluid/system boundary, evidence, energy and named stop or release authority; do not infer values or permission.

Row 1

Question

Is equipment used at work?

Route

GB or NI PUWER baseline.

Evidence

Task and equipment assessment.

Row 2

Question

Does it lift or lower a load?

Route

GB or NI LOLER applicability review.

Evidence

Lift plan, marking and examination evidence.

Row 3

Question

Does it meet pressure-system scope?

Route

GB PSSR 2000 or NI PSSR 2004 applicability review.

Evidence

System boundary, fluid, limits and written scheme decision.

Row 4

Question

Is it being placed on a market?

Route

Current sector product-supply law.

Evidence

Conformity evidence, separate from workplace acceptance.

Read the complete comparison table
How do PUWER, LOLER and pressure-system law fit together?
RowQuestionRouteEvidence
1Is equipment used at work?GB or NI PUWER baseline.Task and equipment assessment.
2Does it lift or lower a load?GB or NI LOLER applicability review.Lift plan, marking and examination evidence.
3Does it meet pressure-system scope?GB PSSR 2000 or NI PSSR 2004 applicability review.System boundary, fluid, limits and written scheme decision.
4Is it being placed on a market?Current sector product-supply law.Conformity evidence, separate from workplace acceptance.
Apply task-specific ERICPD and HSE control hierarchy

Table ID: work-equipment-lifting-equipment-and-pressure-systems-control-hierarchy-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html

Row 1

Column 1

Eliminate

Column 2

Elimination

Column 3

Avoid an unnecessary suspended lift or pressure-dependent step by redesigning flow or assembling at a safe accessible position. Check whether gravity, stored energy or manual handling creates a new hazard in the alternative.

Column 4

Process and engineering owners verify the revised task and residual energy. Hold the original operation until feasible avoidance and the alternative’s risks are assessed. Basis: HSE Planning and organising lifting operations; HSE Using pressure systems

Row 2

Column 1

Reduce, including substitution

Column 2

Substitution or safer design

Column 3

Choose a lifting or process method with suitable capacity and controlled interfaces for the actual load, radius, pressure and substance. Do not assume a lower pressure, different lifting device or powered aid is suitable without assessing the full task.

Column 4

Competent lift planner or pressure-system engineer verifies design limits, stability, compatibility and foreseeable use. Reject a substitute with unverified capacity or new trapping/pressure hazards. Basis: HSE Planning and organising lifting operations; HSE L122 Safety of pressure systems

Row 3

Column 1

Isolate

Column 2

Engineering where physical or technical separation is feasible

Column 3

Provide designed physical safeguards: separation from suspended loads, suitable lifting installation and pressure-system protective devices. Intrusive work needs verified isolation and safe control of stored pressure under an approved method.

Column 4

Engineering owner verifies installation and protective performance; authorised task owner confirms the safe state. Stop when lifting support, separation, pressure protection or isolation is uncertain. Basis: HSE L113 Safe use of lifting equipment; HSE L122 Safety of pressure systems; HSE Maintenance of work equipment

Row 4

Column 1

Control

Column 2

Administrative or organisational controls

Column 3

Plan and supervise lifting to its complexity and define pressure-system operating limits and required written scheme/examination arrangements. Keep the distinct PUWER, LOLER and pressure decisions; a pre-use check is not a substitute for a required competent examination.

Column 4

Lift planner, user/owner and competent examiner fulfil their separate roles. Hold a lift or qualifying system use when critical planning, limits or required examination are unresolved. Basis: HSE Planning and organising lifting operations; HSE Thorough examinations and inspections of lifting equipment; HSE Using pressure systems

Row 5

Column 1

PPE

Column 2

Personal protective equipment for residual exposure

Column 3

Select PPE for remaining handling, splash or other task exposure, checking fit and compatibility. It does not protect a person from an uncontrolled suspended load or establish that a pressurised vessel is safe.

Column 4

Competent task owner verifies protection and safe position. Stop if required residual protection fails and keep people outside uncontrolled load or release zones. Basis: HSE hierarchy of control; HSE L113 Safe use of lifting equipment; HSE L122 Safety of pressure systems

Row 6

Column 1

Discipline

Column 2

Sustain and improve all levels

Column 3

Maintain equipment and protective devices, complete required examinations and close defects through competent decisions. Reassess after modifications, changed service, new loads or repeated failures.

Column 4

Owner and competent specialists verify repair, examination and release evidence. Hold use for a serious defect or unclear authorised return-to-service decision. Basis: HSE Thorough examinations and inspections of lifting equipment; HSE L122 Safety of pressure systems; HSE Maintenance of work equipment

Read the complete comparison table
Apply task-specific ERICPD and HSE control hierarchy
RowColumn 1Column 2Column 3Column 4
1EliminateEliminationAvoid an unnecessary suspended lift or pressure-dependent step by redesigning flow or assembling at a safe accessible position. Check whether gravity, stored energy or manual handling creates a new hazard in the alternative.Process and engineering owners verify the revised task and residual energy. Hold the original operation until feasible avoidance and the alternative’s risks are assessed. Basis: HSE Planning and organising lifting operations; HSE Using pressure systems
2Reduce, including substitutionSubstitution or safer designChoose a lifting or process method with suitable capacity and controlled interfaces for the actual load, radius, pressure and substance. Do not assume a lower pressure, different lifting device or powered aid is suitable without assessing the full task.Competent lift planner or pressure-system engineer verifies design limits, stability, compatibility and foreseeable use. Reject a substitute with unverified capacity or new trapping/pressure hazards. Basis: HSE Planning and organising lifting operations; HSE L122 Safety of pressure systems
3IsolateEngineering where physical or technical separation is feasibleProvide designed physical safeguards: separation from suspended loads, suitable lifting installation and pressure-system protective devices. Intrusive work needs verified isolation and safe control of stored pressure under an approved method.Engineering owner verifies installation and protective performance; authorised task owner confirms the safe state. Stop when lifting support, separation, pressure protection or isolation is uncertain. Basis: HSE L113 Safe use of lifting equipment; HSE L122 Safety of pressure systems; HSE Maintenance of work equipment
4ControlAdministrative or organisational controlsPlan and supervise lifting to its complexity and define pressure-system operating limits and required written scheme/examination arrangements. Keep the distinct PUWER, LOLER and pressure decisions; a pre-use check is not a substitute for a required competent examination.Lift planner, user/owner and competent examiner fulfil their separate roles. Hold a lift or qualifying system use when critical planning, limits or required examination are unresolved. Basis: HSE Planning and organising lifting operations; HSE Thorough examinations and inspections of lifting equipment; HSE Using pressure systems
5PPEPersonal protective equipment for residual exposureSelect PPE for remaining handling, splash or other task exposure, checking fit and compatibility. It does not protect a person from an uncontrolled suspended load or establish that a pressurised vessel is safe.Competent task owner verifies protection and safe position. Stop if required residual protection fails and keep people outside uncontrolled load or release zones. Basis: HSE hierarchy of control; HSE L113 Safe use of lifting equipment; HSE L122 Safety of pressure systems
6DisciplineSustain and improve all levelsMaintain equipment and protective devices, complete required examinations and close defects through competent decisions. Reassess after modifications, changed service, new loads or repeated failures.Owner and competent specialists verify repair, examination and release evidence. Hold use for a serious defect or unclear authorised return-to-service decision. Basis: HSE Thorough examinations and inspections of lifting equipment; HSE L122 Safety of pressure systems; HSE Maintenance of work equipment
How is lifting equipment selected and rated?

Table ID: work-equipment-lifting-equipment-and-pressure-systems-lifting-selection-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html Scope: Great Britain|Northern Ireland: How is lifting equipment selected and rated?. Decide actual equipment, operating or intervention mode, load/configuration or relevant fluid/system boundary, evidence, energy and named stop or release authority; do not infer values or permission.

Row 1

Decision

Load and attachment

Evidence

Known mass, shape, balance and compatible device.

Stop

Unknown or mismatched load.

Row 2

Decision

Strength and stability

Evidence

Rated configuration, support and siting.

Stop

Unverified ground or configuration.

Row 3

Decision

Lift path

Evidence

Clear route, exclusions and communication.

Stop

People or obstruction in danger path.

Read the complete comparison table
How is lifting equipment selected and rated?
RowDecisionEvidenceStop
1Load and attachmentKnown mass, shape, balance and compatible device.Unknown or mismatched load.
2Strength and stabilityRated configuration, support and siting.Unverified ground or configuration.
3Lift pathClear route, exclusions and communication.People or obstruction in danger path.
Who plans and supervises lifting operations?

Table ID: work-equipment-lifting-equipment-and-pressure-systems-lifting-plan-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html Scope: Great Britain|Northern Ireland: Who plans and supervises lifting operations?. Decide actual equipment, operating or intervention mode, load/configuration or relevant fluid/system boundary, evidence, energy and named stop or release authority; do not infer values or permission.

Row 1

Stage

Plan

Decision

Match equipment, load, people, place and sequence.

Hold

Unknown facts or unresolved interface.

Row 2

Stage

Brief

Decision

Check who directs, operates, attaches and stops.

Hold

Conflicting roles or signals.

Row 3

Stage

Execute

Decision

Monitor load and conditions against plan.

Hold

Unexpected movement or changed condition.

Read the complete comparison table
Who plans and supervises lifting operations?
RowStageDecisionHold
1PlanMatch equipment, load, people, place and sequence.Unknown facts or unresolved interface.
2BriefCheck who directs, operates, attaches and stops.Conflicting roles or signals.
3ExecuteMonitor load and conditions against plan.Unexpected movement or changed condition.
How is LOLER thorough examination different from inspection?

Table ID: work-equipment-lifting-equipment-and-pressure-systems-lifting-examination-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html Scope: Great Britain|Northern Ireland: How is LOLER thorough examination different from inspection?. Decide actual equipment, operating or intervention mode, load/configuration or relevant fluid/system boundary, evidence, energy and named stop or release authority; do not infer values or permission.

Row 1

Activity

User check

Purpose

Spot obvious current defect before use.

Who decides

Trained user and local method.

Row 2

Activity

PUWER inspection

Purpose

Detect installation or deterioration issues.

Who decides

Risk assessment and competent inspector.

Row 3

Activity

LOLER thorough examination

Purpose

Statutory safety assessment and report.

Who decides

Competent examiner and law or scheme.

Row 4

Activity

Maintenance

Purpose

Keep equipment safe and functional.

Who decides

Equipment owner and competent maintainer.

Read the complete comparison table
How is LOLER thorough examination different from inspection?
RowActivityPurposeWho decides
1User checkSpot obvious current defect before use.Trained user and local method.
2PUWER inspectionDetect installation or deterioration issues.Risk assessment and competent inspector.
3LOLER thorough examinationStatutory safety assessment and report.Competent examiner and law or scheme.
4MaintenanceKeep equipment safe and functional.Equipment owner and competent maintainer.
When does pressure-system law apply?

Table ID: work-equipment-lifting-equipment-and-pressure-systems-pressure-scope-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html Scope: Great Britain|Northern Ireland: When does pressure-system law apply?. Decide actual equipment, operating or intervention mode, load/configuration or relevant fluid/system boundary, evidence, energy and named stop or release authority; do not infer values or permission.

Row 1

Question

What is the relevant fluid?

Evidence

Fluid and operating conditions.

Do not infer

Every pressurised liquid is PSSR.

Row 2

Question

What is the system boundary?

Evidence

Vessels, pipework, pipeline and protection.

Do not infer

One label covers every component.

Row 3

Question

Is an exception relevant?

Evidence

Current GB or NI Schedule and competent review.

Do not infer

An exemption from one duty removes all safety duties.

Read the complete comparison table
When does pressure-system law apply?
RowQuestionEvidenceDo not infer
1What is the relevant fluid?Fluid and operating conditions.Every pressurised liquid is PSSR.
2What is the system boundary?Vessels, pipework, pipeline and protection.One label covers every component.
3Is an exception relevant?Current GB or NI Schedule and competent review.An exemption from one duty removes all safety duties.
What is a written scheme of examination?

Table ID: work-equipment-lifting-equipment-and-pressure-systems-pressure-written-scheme-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html Scope: Great Britain|Northern Ireland: What is a written scheme of examination?. Decide actual equipment, operating or intervention mode, load/configuration or relevant fluid/system boundary, evidence, energy and named stop or release authority; do not infer values or permission.

Row 1

Element

Scope

Decision

Which vessels, pipelines, pipework and protective devices?

Evidence

Identified boundary and exclusions.

Row 2

Element

Method and timing

Decision

How and when each part is examined?

Evidence

Competent-person certified scheme.

Row 3

Element

Preparation

Decision

How is examination made safe?

Evidence

Isolation, access and special measures.

Row 4

Element

Change

Decision

Does modified use require revision?

Evidence

Scheme review and certification.

Read the complete comparison table
What is a written scheme of examination?
RowElementDecisionEvidence
1ScopeWhich vessels, pipelines, pipework and protective devices?Identified boundary and exclusions.
2Method and timingHow and when each part is examined?Competent-person certified scheme.
3PreparationHow is examination made safe?Isolation, access and special measures.
4ChangeDoes modified use require revision?Scheme review and certification.
How does pressure-system examination work?

Table ID: work-equipment-lifting-equipment-and-pressure-systems-pressure-examination-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html Scope: Great Britain|Northern Ireland: How does pressure-system examination work?. Decide actual equipment, operating or intervention mode, load/configuration or relevant fluid/system boundary, evidence, energy and named stop or release authority; do not infer values or permission.

Row 1

Step

Before

Evidence

Current suitable written scheme and safe preparation.

Hold

No scheme or unsafe access.

Row 2

Step

Examine

Evidence

Competent examination to scheme.

Hold

Unexamined required part.

Row 3

Step

Report and act

Evidence

Findings, due dates and danger action.

Hold

Unsafe finding not closed.

Read the complete comparison table
How does pressure-system examination work?
RowStepEvidenceHold
1BeforeCurrent suitable written scheme and safe preparation.No scheme or unsafe access.
2ExamineCompetent examination to scheme.Unexamined required part.
3Report and actFindings, due dates and danger action.Unsafe finding not closed.
Can one inspection or certificate cover every duty?

Table ID: work-equipment-lifting-equipment-and-pressure-systems-examination-comparison-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html Scope: Great Britain|Northern Ireland: Can one inspection or certificate cover every duty?. Decide actual equipment, operating or intervention mode, load/configuration or relevant fluid/system boundary, evidence, energy and named stop or release authority; do not infer values or permission.

Row 1

Record

Pre-use check

What it proves

Current obvious condition.

What it does not prove

Statutory examination.

Row 2

Record

PUWER inspection

What it proves

Relevant installation or deterioration findings.

What it does not prove

LOLER or PSSR compliance by itself.

Row 3

Record

LOLER report

What it proves

Competent lifting examination.

What it does not prove

Safe lift plan or maintenance.

Row 4

Record

Pressure written scheme

What it proves

Examination plan and scope.

What it does not prove

Completed examination or repair.

Row 5

Record

Pressure report

What it proves

Findings to the scheme.

What it does not prove

Product conformity or operation within limits.

Row 6

Record

Product declaration

What it proves

Applicable supply assessment.

What it does not prove

Safe workplace use.

Read the complete comparison table
Can one inspection or certificate cover every duty?
RowRecordWhat it provesWhat it does not prove
1Pre-use checkCurrent obvious condition.Statutory examination.
2PUWER inspectionRelevant installation or deterioration findings.LOLER or PSSR compliance by itself.
3LOLER reportCompetent lifting examination.Safe lift plan or maintenance.
4Pressure written schemeExamination plan and scope.Completed examination or repair.
5Pressure reportFindings to the scheme.Product conformity or operation within limits.
6Product declarationApplicable supply assessment.Safe workplace use.
How do lifting and pressure controls change across settings? decision table

Table ID: work-equipment-lifting-equipment-and-pressure-systems-sector-transfer

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html

Row 1

Column 1

Warehouse lift truck

Column 2

Elevated load can fall while steering or brakes also fail.

Column 3

Check lifting parts under LOLER and other safety parts under PUWER; segregate pedestrians.

Row 2

Column 1

Care setting hoist

Column 2

Person can fall or be injured by wrong sling or attachment.

Column 3

Match person, sling and hoist, plan the transfer and verify current examination.

Row 3

Column 1

Construction lift

Column 2

Ground, reach and wind can exceed configuration.

Column 3

Competent lift plan, rated setup and exclusion zone.

Row 4

Column 1

Boiler or autoclave

Column 2

Pressure, heat or failed protection can release energy.

Column 3

Safe limits, written scheme and competent examination before operation.

Read the complete comparison table
How do lifting and pressure controls change across settings? decision table
RowColumn 1Column 2Column 3
1Warehouse lift truckElevated load can fall while steering or brakes also fail.Check lifting parts under LOLER and other safety parts under PUWER; segregate pedestrians.
2Care setting hoistPerson can fall or be injured by wrong sling or attachment.Match person, sling and hoist, plan the transfer and verify current examination.
3Construction liftGround, reach and wind can exceed configuration.Competent lift plan, rated setup and exclusion zone.
4Boiler or autoclavePressure, heat or failed protection can release energy.Safe limits, written scheme and competent examination before operation.
Which Great Britain law applies to these decisions?

Table ID: work-equipment-lifting-equipment-and-pressure-systems-legal-gb-combined-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html Scope: Great Britain: Which Great Britain law applies to these decisions?. Decide actual equipment, operating or intervention mode, load/configuration or relevant fluid/system boundary, evidence, energy and named stop or release authority; do not infer values or permission.

Row 1

Gb route

PUWER 1998

Decision

Safe work-equipment use.

Source

SI 1998/2306 and L22. See Provision and Use of Work Equipment Regulations 1998.

Row 2

Gb route

LOLER 1998

Decision

Lifting plan, equipment and examination.

Source

SI 1998/2307 and L113. See Lifting Operations and Lifting Equipment Regulations 1998.

Row 3

Gb route

PSSR 2000

Decision

Safe limits, written scheme and examination.

Source

SI 2000/128 and L122. See Pressure Systems Safety Regulations 2000.

Row 4

Gb route

Product supply

Decision

Market placement and conformity.

Source

Current sector guidance. See GOV.UK placing UKCA or CE marked products on the Great Britain market.

Read the complete comparison table
Which Great Britain law applies to these decisions?
RowGb routeDecisionSource
1PUWER 1998Safe work-equipment use.SI 1998/2306 and L22. See Provision and Use of Work Equipment Regulations 1998.
2LOLER 1998Lifting plan, equipment and examination.SI 1998/2307 and L113. See Lifting Operations and Lifting Equipment Regulations 1998.
3PSSR 2000Safe limits, written scheme and examination.SI 2000/128 and L122. See Pressure Systems Safety Regulations 2000.
4Product supplyMarket placement and conformity.Current sector guidance. See GOV.UK placing UKCA or CE marked products on the Great Britain market.
Which Northern Ireland law applies to these decisions?

Table ID: work-equipment-lifting-equipment-and-pressure-systems-legal-ni-combined-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html Scope: Northern Ireland: Which Northern Ireland law applies to these decisions?. Decide actual equipment, operating or intervention mode, load/configuration or relevant fluid/system boundary, evidence, energy and named stop or release authority; do not infer values or permission.

Row 1

Ni route

PUWER NI 1999

Decision

Safe work-equipment use.

Source

SR 1999/305. See Provision and Use of Work Equipment Regulations Northern Ireland 1999.

Row 2

Ni route

LOLER NI 1999

Decision

Lifting planning and examination.

Source

SR 1999/304. See Lifting Operations and Lifting Equipment Regulations Northern Ireland 1999.

Row 3

Ni route

PSSR NI 2004

Decision

Safe limits and written scheme.

Source

SR 2004/222. See Pressure Systems Safety Regulations Northern Ireland 2004.

Row 4

Ni route

L122 in NI

Decision

ACOP approval context.

Source

HSENI approval page. See HSENI L122 approved for use in Northern Ireland.

Read the complete comparison table
Which Northern Ireland law applies to these decisions?
RowNi routeDecisionSource
1PUWER NI 1999Safe work-equipment use.SR 1999/305. See Provision and Use of Work Equipment Regulations Northern Ireland 1999.
2LOLER NI 1999Lifting planning and examination.SR 1999/304. See Lifting Operations and Lifting Equipment Regulations Northern Ireland 1999.
3PSSR NI 2004Safe limits and written scheme.SR 2004/222. See Pressure Systems Safety Regulations Northern Ireland 2004.
4L122 in NIACOP approval context.HSENI approval page. See HSENI L122 approved for use in Northern Ireland.
What is the guarding hierarchy?

Table ID: work-equipment-lifting-equipment-and-pressure-systems-guarding-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html Scope: Great Britain|Northern Ireland: What is the guarding hierarchy?. Decide actual equipment, operating or intervention mode, load/configuration or relevant fluid/system boundary, evidence, energy and named stop or release authority; do not infer values or permission.

Row 1

Priority

1

Control

Fixed guard.

Boundary

Use where practicable and compatible with necessary access.

Row 2

Priority

2

Control

Other guard or protection device.

Boundary

Must fail or act to a safe condition as designed.

Row 3

Priority

3

Control

Jig, holder, push-stick or similar aid.

Boundary

Keeps the person from danger where higher controls cannot fully apply.

Row 4

Priority

4

Control

Information, training, supervision and PPE.

Boundary

Residual layer, not a substitute for practicable safeguarding.

Read the complete comparison table
What is the guarding hierarchy?
RowPriorityControlBoundary
11Fixed guard.Use where practicable and compatible with necessary access.
22Other guard or protection device.Must fail or act to a safe condition as designed.
33Jig, holder, push-stick or similar aid.Keeps the person from danger where higher controls cannot fully apply.
44Information, training, supervision and PPE.Residual layer, not a substitute for practicable safeguarding.
How should equipment be isolated?

Table ID: work-equipment-lifting-equipment-and-pressure-systems-isolation-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html Scope: Great Britain|Northern Ireland: How should equipment be isolated?. Decide actual equipment, operating or intervention mode, load/configuration or relevant fluid/system boundary, evidence, energy and named stop or release authority; do not infer values or permission.

Row 1

Energy or stage

Identify

Control question

What can move, energise, pressurise, heat or release?

Evidence

Energy map and instructions.

Row 2

Energy or stage

Separate and secure

Control question

Can reconnection or release be prevented?

Evidence

Isolation and lock-off record.

Row 3

Energy or stage

Dissipate or restrain

Control question

What stored energy remains?

Evidence

Verified zero or safely restrained state.

Row 4

Energy or stage

Restore

Control question

Are people clear and safeguards restored?

Evidence

Controlled handback and release.

Read the complete comparison table
How should equipment be isolated?
RowEnergy or stageControl questionEvidence
1IdentifyWhat can move, energise, pressurise, heat or release?Energy map and instructions.
2Separate and secureCan reconnection or release be prevented?Isolation and lock-off record.
3Dissipate or restrainWhat stored energy remains?Verified zero or safely restrained state.
4RestoreAre people clear and safeguards restored?Controlled handback and release.
What must each role learn and demonstrate? decision table

Table ID: work-equipment-lifting-equipment-and-pressure-systems-role-competence

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html

Row 1

Column 1

Worker or operator

Column 2

Explain the task risk, pre-use check and when to stop.

Column 3

New task, equipment or unsafe event.

Row 2

Column 1

Supervisor or manager

Column 2

Select and verify controls, allocate resources and act on reports.

Column 3

Work pattern, staffing, process or equipment change.

Row 3

Column 1

Maintainer or specialist

Column 2

Show the technical basis, safe state, examination or referral within own competence.

Column 3

Modified system, failed test or new evidence.

Row 4

Column 1

Safety adviser or auditor

Column 2

Trace law, hazard, control and field evidence without substituting a checklist for judgement.

Column 3

Regulatory or technical change.

Read the complete comparison table
What must each role learn and demonstrate? decision table
RowColumn 1Column 2Column 3
1Worker or operatorExplain the task risk, pre-use check and when to stop.New task, equipment or unsafe event.
2Supervisor or managerSelect and verify controls, allocate resources and act on reports.Work pattern, staffing, process or equipment change.
3Maintainer or specialistShow the technical basis, safe state, examination or referral within own competence.Modified system, failed test or new evidence.
4Safety adviser or auditorTrace law, hazard, control and field evidence without substituting a checklist for judgement.Regulatory or technical change.
What do complete work-equipment decisions look like?

Table ID: work-equipment-lifting-equipment-and-pressure-systems-operational-examples-table

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html Scope: Great Britain|Northern Ireland: What do complete work-equipment decisions look like?. Decide actual equipment, operating or intervention mode, load/configuration or relevant fluid/system boundary, evidence, energy and named stop or release authority; do not infer values or permission.

Row 1

Scenario type

Routine use

Primary decision

Start only after suitability, safeguards and checks pass.

End state

Controlled completion.

Row 2

Scenario type

Hire or contractor

Primary decision

Accept only after duties and evidence align.

End state

Accepted, rejected or held.

Row 3

Scenario type

Defect or emergency

Primary decision

Stop and prevent restart.

End state

Quarantine or authorised return.

Row 4

Scenario type

Maintenance or change

Primary decision

Control energy and evidence.

End state

Verified handback.

Read the complete comparison table
What do complete work-equipment decisions look like?
RowScenario typePrimary decisionEnd state
1Routine useStart only after suitability, safeguards and checks pass.Controlled completion.
2Hire or contractorAccept only after duties and evidence align.Accepted, rejected or held.
3Defect or emergencyStop and prevent restart.Quarantine or authorised return.
4Maintenance or changeControl energy and evidence.Verified handback.
Source tables and records 2
Official source and decision register

Table ID: work-equipment-lifting-equipment-and-pressure-systems-official-links

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html

Row 1

Column 1

HSE

Column 2

HSE PUWER overview

Column 3

Great Britain guidance

Column 4

Primary overview of suitability, maintenance, inspection, competence, guarding, controls and other PUWER duties in Great Britain.; Updated 21 November 2024; checked 23 September 2026

Row 2

Column 1

HSENI

Column 2

HSENI PUWER 1999

Column 3

Northern Ireland guidance

Column 4

Northern Ireland PUWER route and regulator guidance.; Publisher publication/update date not stated; current page checked 23 September 2026

Row 3

Column 1

HSE

Column 2

HSE L22 Safe use of work equipment

Column 3

Great Britain ACOP and guidance

Column 4

Detailed PUWER ACOP and guidance. Product-law wording must be read with current GOV.UK market guidance.; Fourth edition 2014, amended 2018; retained copy inspected

Row 4

Column 1

HSE

Column 2

HSE INDG229 Using work equipment safely

Column 3

Great Britain worker guidance

Column 4

Worker-level use, defects and controls. Dated examples are not universal limits or frequencies.; Revision 2, November 2012; retained copy inspected

Row 5

Column 1

HSE

Column 2

HSE PUWER guidance and topic index

Column 3

Great Britain guidance

Column 4

Practical Great Britain route for selecting, installing, using and controlling work equipment.; Updated 16 March 2023; checked 23 September 2026

Row 6

Column 1

legislation.gov.uk

Column 2

Provision and Use of Work Equipment Regulations 1998

Column 3

Great Britain

Column 4

Great Britain work-equipment duties; check current effects and application.; SI 1998/2306, as amended

Row 7

Column 1

legislation.gov.uk

Column 2

Provision and Use of Work Equipment Regulations Northern Ireland 1999

Column 3

Northern Ireland

Column 4

Separate Northern Ireland work-equipment duties; check current effects and application.; SR 1999/305, as amended

Row 8

Column 1

HSE

Column 2

HSE Introduction to work equipment and machinery

Column 3

Great Britain guidance

Column 4

Boundary between safe workplace use, machinery safety and product supply.; Updated 19 November 2024; checked 23 September 2026

Row 9

Column 1

GOV.UK

Column 2

GOV.UK placing UKCA or CE marked products on the Great Britain market

Column 3

Great Britain product supply

Column 4

Current GB market route. A conformity mark does not prove suitability or safe workplace use.; Published 31 March 2026; updated 21 August 2026

Row 10

Column 1

GOV.UK

Column 2

GOV.UK placing CE or CE and UKNI marked products on the Northern Ireland market

Column 3

Northern Ireland product supply

Column 4

Current NI market route under applicable Windsor Framework product rules; separate from workplace-use duties.; Published 31 March 2026; updated 8 April 2026

Row 11

Column 1

GOV.UK

Column 2

GOV.UK product regulations by sector and current marking approaches

Column 3

United Kingdom product supply

Column 4

Sector table for identifying the applicable current product regime; it does not authorise workplace use.; Published 31 March 2026

Row 12

Column 1

legislation.gov.uk

Column 2

Lifting Operations and Lifting Equipment Regulations 1998

Column 3

Great Britain

Column 4

Great Britain lifting equipment, operations, examination, reporting and record duties.; SI 1998/2307, as amended

Row 13

Column 1

legislation.gov.uk

Column 2

Lifting Operations and Lifting Equipment Regulations Northern Ireland 1999

Column 3

Northern Ireland

Column 4

Northern Ireland lifting-equipment regime; do not present GB LOLER as UK-wide.; SR 1999/304, as amended

Row 14

Column 1

legislation.gov.uk

Column 2

Pressure Systems Safety Regulations 2000

Column 3

Great Britain

Column 4

Great Britain pressure-system duties, including safe operating limits and written schemes where applicable.; SI 2000/128, as amended

Row 15

Column 1

legislation.gov.uk

Column 2

Pressure Systems Safety Regulations Northern Ireland 2004

Column 3

Northern Ireland

Column 4

Northern Ireland pressure-system duties; check applicable scope and current effects.; SR 2004/222, as amended

Row 16

Column 1

HSE

Column 2

HSE Pressure Equipment Safety Regulations guidance

Column 3

Great Britain pressure product supply guidance

Column 4

Product-supply boundary for pressure equipment; not approval for workplace use.; Updated 9 December 2024; checked 23 September 2026

Row 17

Column 1

HSE

Column 2

HSE LOLER overview

Column 3

Great Britain guidance

Column 4

Separate lifting-equipment regime where applicable; PUWER alone is not the complete legal route.; Updated 22 January 2026; checked 23 September 2026

Row 18

Column 1

HSE

Column 2

HSE L113 Safe use of lifting equipment

Column 3

Great Britain ACOP and guidance

Column 4

Detailed LOLER ACOP and guidance; apply to actual equipment, task and jurisdiction.; Second edition 2014, amended 2018; retained copy inspected

Row 19

Column 1

HSENI

Column 2

HSENI Work equipment and machinery guidance

Column 3

Northern Ireland guidance

Column 4

NI PUWER and LOLER routes, including lifting-specific examination.; Publisher publication/update date not stated; current page checked 23 September 2026

Row 20

Column 1

HSE

Column 2

HSE Planning and organising lifting operations

Column 3

Great Britain guidance

Column 4

Risk-proportionate competent planning, supervision, strength, siting and load control.; Updated 29 October 2024; checked 23 September 2026

Row 21

Column 1

HSE

Column 2

HSE Magnetic lifting devices

Column 3

Great Britain specialist lifting guidance

Column 4

Load and attachment compatibility illustration; do not generalise device-specific technical values.; Updated 29 October 2024; checked 23 September 2026

Row 22

Column 1

HSE

Column 2

HSE Vacuum lifting equipment

Column 3

Great Britain specialist lifting guidance

Column 4

Vacuum-lifting compatibility and failure-mode route; equipment-specific controls remain local.; Updated 21 November 2024; checked 23 September 2026

Row 23

Column 1

HSE

Column 2

HSE Thorough examinations and inspections of lifting equipment

Column 3

Great Britain guidance

Column 4

Distinguishes pre-use checks, risk-based inspections, statutory thorough examination and maintenance; specific intervals require the applicable law or competent scheme.; Updated 29 October 2024; checked 23 September 2026

Row 24

Column 1

HSE

Column 2

HSE GEIS6 MEWP selection management and use

Column 3

Great Britain MEWP guidance

Column 4

MEWP specialist selection and work-at-height route alongside lifting duties.; 2014; retained copy inspected

Row 25

Column 1

HSE

Column 2

HSE Work at height

Column 3

Great Britain guidance

Column 4

Separate work-at-height duties where equipment is used for access or positioning.; Current portal checked 23 September 2026

Row 26

Column 1

HSE

Column 2

HSE Inspection of work equipment

Column 3

Great Britain guidance

Column 4

Risk-based inspection, records and evidence; does not set a universal inspection interval.; Updated 29 October 2024; checked 23 September 2026

Row 27

Column 1

HSE

Column 2

HSE Maintenance of work equipment

Column 3

Great Britain guidance

Column 4

Planning, competence, safe maintenance, isolation and protection of maintainers and others.; Updated 19 November 2024; checked 23 September 2026

Row 28

Column 1

HSE

Column 2

HSE Work equipment and machinery FAQs

Column 3

Great Britain guidance

Column 4

Official answers on responsibilities, hire, inspection, training and equipment supplied for use.; Updated 7 May 2026; checked 23 September 2026

Row 29

Column 1

HSE

Column 2

HSE Pressure Systems Safety Regulations overview

Column 3

Great Britain guidance

Column 4

Pressure-system applicability, written schemes, competent persons and user or owner duties.; Updated 9 December 2025; checked 23 September 2026

Row 30

Column 1

HSE

Column 2

HSE Using pressure systems

Column 3

Great Britain guidance

Column 4

Safe equipment, limits, protective devices, maintenance, training, written scheme and competent examination.; Updated 10 October 2024; checked 23 September 2026

Row 31

Column 1

HSE

Column 2

HSE L122 Safety of pressure systems

Column 3

Great Britain ACOP and guidance

Column 4

Detailed PSSR scope, written-scheme content, competent-person role, examinations, defects and records.; 2014; retained copy inspected

Row 32

Column 1

HSENI

Column 2

HSENI L122 approved for use in Northern Ireland

Column 3

Northern Ireland ACOP approval

Column 4

Confirms L122 ACOP approval in NI alongside NI PSSR 2004; apply NI legislation.; Published 20 May 2004; checked 23 September 2026

Row 33

Column 1

HSE

Column 2

HSE HSG221 Offshore lifting equipment

Column 3

Great Britain offshore lifting guidance

Column 4

Offshore-specific lifting route, not a generic workplace rule.; Second edition 2007; retained copy inspected

Row 34

Column 1

HSE

Column 2

HSE PM73 Safety requirements for autoclaves

Column 3

Great Britain industrial autoclave guidance

Column 4

Autoclave-specific safeguarding, maintenance and pressure-system context.; Revision 3, 2012; retained copy inspected

Row 35

Column 1

HSE

Column 2

HSE INDG291 Providing and using work equipment safely

Column 3

Great Britain guidance

Column 4

Broad practical PUWER guide; current HSE and GOV.UK pages control later legal or product-supply changes.; Revision 1, March 2013; retained copy inspected

Row 36

Column 1

legislation.gov.uk

Column 2

Management of Health and Safety at Work Regulations 1999

Column 3

Great Britain

Column 4

Great Britain risk assessment, preventive arrangements, coordination, emergency and competent-assistance route.; SI 1999/3242, as amended

Row 37

Column 1

legislation.gov.uk

Column 2

Management of Health and Safety at Work Regulations Northern Ireland 2000

Column 3

Northern Ireland

Column 4

Separate Northern Ireland risk assessment, coordination, emergency and competent-assistance route.; SR 2000/388, as amended

Row 38

Column 1

HSENI

Column 2

HSENI machinery safety devices safety alert

Column 3

Northern Ireland safety alert

Column 4

Current warning on bypassed safety devices; apply to the equipment and conditions within scope.; Published 4 March 2026; checked 23 September 2026

Row 39

Column 1

HSE

Column 2

HSE Electrical safety at work

Column 3

Great Britain guidance

Column 4

Separate electrical risk, isolation and competence route where applicable.; Current portal checked 23 September 2026

Row 40

Column 1

HSENI

Column 2

HSENI Refurbished and modified machinery

Column 3

Northern Ireland guidance

Column 4

Refurbishment and modification boundaries, including possible manufacturer and product-supply consequences.; Publisher publication/update date not stated; current page checked 23 September 2026

Row 41

Column 1

HSE

Column 2

HSE Training and competence for work equipment

Column 3

Great Britain guidance

Column 4

Task- and person-specific competence; no generic certificate or expiry period.; Updated 6 June 2025; checked 23 September 2026

Row 42

Column 1

HSENI

Column 2

HSENI Supplier, importer or hirer of equipment

Column 3

Northern Ireland product and hire guidance

Column 4

Duties that can arise from supply, import or hire; separate from workplace-use control.; Publisher publication/update date not stated; current page checked 23 September 2026

Row 43

Column 1

HSE

Column 2

HSE Pressure systems

Column 3

Great Britain guidance

Column 4

Separate pressure-systems route where applicable.; Current portal checked 23 September 2026

Row 44

Column 1

HSE

Column 2

HSE Dangerous substances and explosive atmospheres

Column 3

Great Britain guidance

Column 4

Separate dangerous-substance and explosive-atmosphere route where equipment can ignite or handle dangerous substances.; Updated 14 October 2024; checked 23 September 2026

Row 45

Column 1

HSE

Column 2

HSE Mobile work equipment

Column 3

Great Britain guidance

Column 4

Additional mobile-equipment considerations; equipment-specific limits and permissions remain local.; Updated 29 October 2024; checked 23 September 2026

Row 46

Column 1

HSE

Column 2

HSE INDG242 Control back-pain risks from whole-body vibration

Column 3

Great Britain sector guidance

Column 4

Mobile-machinery and whole-body-vibration context, not a generic PUWER design authority.; Revision 1, June 2005; retained copy inspected

Row 47

Column 1

HSENI

Column 2

HSENI Working safely with farm equipment and vehicles

Column 3

Northern Ireland sector guidance

Column 4

Sector examples for guards, maintenance and safe use; transfer only where conditions match.; Publisher publication/update date not stated; current page checked 23 September 2026

Row 48

Column 1

legislation.gov.uk

Column 2

Health and Safety at Work etc Act 1974

Column 3

Great Britain

Column 4

Great Britain foundation for safe plant, systems, information, training, supervision and protection of others.; 1974 c.37, as amended

Row 49

Column 1

legislation.gov.uk

Column 2

Health and Safety at Work Northern Ireland Order 1978

Column 3

Northern Ireland

Column 4

Northern Ireland foundation for safe plant, systems, information, training, supervision and protection of others.; SI 1978/1039, as amended

Row 50

Column 1

HSE

Column 2

HSE INDG474 Lifting equipment at work

Column 3

Great Britain lifting guidance

Column 4

Current brief LOLER guide; supersedes the withdrawn retained INDG290 and INDG422 leaflets.; Published April 2017; checked 23 September 2026

Row 51

Column 1

HSE

Column 2

HSE Managing risk using PPE

Column 3

Great Britain

Column 4

Five-level control hierarchy and PPE boundary; Current page; date not displayed

Row 52

Column 1

HSE

Column 2

HSE Managing for health and safety (HSG65)

Column 3

Great Britain

Column 4

Current source at verification date; Live source; check the linked page for updates

Read the complete comparison table
Official source and decision register
RowColumn 1Column 2Column 3Column 4
1HSEHSE PUWER overviewGreat Britain guidancePrimary overview of suitability, maintenance, inspection, competence, guarding, controls and other PUWER duties in Great Britain.; Updated 21 November 2024; checked 23 September 2026
2HSENIHSENI PUWER 1999Northern Ireland guidanceNorthern Ireland PUWER route and regulator guidance.; Publisher publication/update date not stated; current page checked 23 September 2026
3HSEHSE L22 Safe use of work equipmentGreat Britain ACOP and guidanceDetailed PUWER ACOP and guidance. Product-law wording must be read with current GOV.UK market guidance.; Fourth edition 2014, amended 2018; retained copy inspected
4HSEHSE INDG229 Using work equipment safelyGreat Britain worker guidanceWorker-level use, defects and controls. Dated examples are not universal limits or frequencies.; Revision 2, November 2012; retained copy inspected
5HSEHSE PUWER guidance and topic indexGreat Britain guidancePractical Great Britain route for selecting, installing, using and controlling work equipment.; Updated 16 March 2023; checked 23 September 2026
6legislation.gov.ukProvision and Use of Work Equipment Regulations 1998Great BritainGreat Britain work-equipment duties; check current effects and application.; SI 1998/2306, as amended
7legislation.gov.ukProvision and Use of Work Equipment Regulations Northern Ireland 1999Northern IrelandSeparate Northern Ireland work-equipment duties; check current effects and application.; SR 1999/305, as amended
8HSEHSE Introduction to work equipment and machineryGreat Britain guidanceBoundary between safe workplace use, machinery safety and product supply.; Updated 19 November 2024; checked 23 September 2026
9GOV.UKGOV.UK placing UKCA or CE marked products on the Great Britain marketGreat Britain product supplyCurrent GB market route. A conformity mark does not prove suitability or safe workplace use.; Published 31 March 2026; updated 21 August 2026
10GOV.UKGOV.UK placing CE or CE and UKNI marked products on the Northern Ireland marketNorthern Ireland product supplyCurrent NI market route under applicable Windsor Framework product rules; separate from workplace-use duties.; Published 31 March 2026; updated 8 April 2026
11GOV.UKGOV.UK product regulations by sector and current marking approachesUnited Kingdom product supplySector table for identifying the applicable current product regime; it does not authorise workplace use.; Published 31 March 2026
12legislation.gov.ukLifting Operations and Lifting Equipment Regulations 1998Great BritainGreat Britain lifting equipment, operations, examination, reporting and record duties.; SI 1998/2307, as amended
13legislation.gov.ukLifting Operations and Lifting Equipment Regulations Northern Ireland 1999Northern IrelandNorthern Ireland lifting-equipment regime; do not present GB LOLER as UK-wide.; SR 1999/304, as amended
14legislation.gov.ukPressure Systems Safety Regulations 2000Great BritainGreat Britain pressure-system duties, including safe operating limits and written schemes where applicable.; SI 2000/128, as amended
15legislation.gov.ukPressure Systems Safety Regulations Northern Ireland 2004Northern IrelandNorthern Ireland pressure-system duties; check applicable scope and current effects.; SR 2004/222, as amended
16HSEHSE Pressure Equipment Safety Regulations guidanceGreat Britain pressure product supply guidanceProduct-supply boundary for pressure equipment; not approval for workplace use.; Updated 9 December 2024; checked 23 September 2026
17HSEHSE LOLER overviewGreat Britain guidanceSeparate lifting-equipment regime where applicable; PUWER alone is not the complete legal route.; Updated 22 January 2026; checked 23 September 2026
18HSEHSE L113 Safe use of lifting equipmentGreat Britain ACOP and guidanceDetailed LOLER ACOP and guidance; apply to actual equipment, task and jurisdiction.; Second edition 2014, amended 2018; retained copy inspected
19HSENIHSENI Work equipment and machinery guidanceNorthern Ireland guidanceNI PUWER and LOLER routes, including lifting-specific examination.; Publisher publication/update date not stated; current page checked 23 September 2026
20HSEHSE Planning and organising lifting operationsGreat Britain guidanceRisk-proportionate competent planning, supervision, strength, siting and load control.; Updated 29 October 2024; checked 23 September 2026
21HSEHSE Magnetic lifting devicesGreat Britain specialist lifting guidanceLoad and attachment compatibility illustration; do not generalise device-specific technical values.; Updated 29 October 2024; checked 23 September 2026
22HSEHSE Vacuum lifting equipmentGreat Britain specialist lifting guidanceVacuum-lifting compatibility and failure-mode route; equipment-specific controls remain local.; Updated 21 November 2024; checked 23 September 2026
23HSEHSE Thorough examinations and inspections of lifting equipmentGreat Britain guidanceDistinguishes pre-use checks, risk-based inspections, statutory thorough examination and maintenance; specific intervals require the applicable law or competent scheme.; Updated 29 October 2024; checked 23 September 2026
24HSEHSE GEIS6 MEWP selection management and useGreat Britain MEWP guidanceMEWP specialist selection and work-at-height route alongside lifting duties.; 2014; retained copy inspected
25HSEHSE Work at heightGreat Britain guidanceSeparate work-at-height duties where equipment is used for access or positioning.; Current portal checked 23 September 2026
26HSEHSE Inspection of work equipmentGreat Britain guidanceRisk-based inspection, records and evidence; does not set a universal inspection interval.; Updated 29 October 2024; checked 23 September 2026
27HSEHSE Maintenance of work equipmentGreat Britain guidancePlanning, competence, safe maintenance, isolation and protection of maintainers and others.; Updated 19 November 2024; checked 23 September 2026
28HSEHSE Work equipment and machinery FAQsGreat Britain guidanceOfficial answers on responsibilities, hire, inspection, training and equipment supplied for use.; Updated 7 May 2026; checked 23 September 2026
29HSEHSE Pressure Systems Safety Regulations overviewGreat Britain guidancePressure-system applicability, written schemes, competent persons and user or owner duties.; Updated 9 December 2025; checked 23 September 2026
30HSEHSE Using pressure systemsGreat Britain guidanceSafe equipment, limits, protective devices, maintenance, training, written scheme and competent examination.; Updated 10 October 2024; checked 23 September 2026
31HSEHSE L122 Safety of pressure systemsGreat Britain ACOP and guidanceDetailed PSSR scope, written-scheme content, competent-person role, examinations, defects and records.; 2014; retained copy inspected
32HSENIHSENI L122 approved for use in Northern IrelandNorthern Ireland ACOP approvalConfirms L122 ACOP approval in NI alongside NI PSSR 2004; apply NI legislation.; Published 20 May 2004; checked 23 September 2026
33HSEHSE HSG221 Offshore lifting equipmentGreat Britain offshore lifting guidanceOffshore-specific lifting route, not a generic workplace rule.; Second edition 2007; retained copy inspected
34HSEHSE PM73 Safety requirements for autoclavesGreat Britain industrial autoclave guidanceAutoclave-specific safeguarding, maintenance and pressure-system context.; Revision 3, 2012; retained copy inspected
35HSEHSE INDG291 Providing and using work equipment safelyGreat Britain guidanceBroad practical PUWER guide; current HSE and GOV.UK pages control later legal or product-supply changes.; Revision 1, March 2013; retained copy inspected
36legislation.gov.ukManagement of Health and Safety at Work Regulations 1999Great BritainGreat Britain risk assessment, preventive arrangements, coordination, emergency and competent-assistance route.; SI 1999/3242, as amended
37legislation.gov.ukManagement of Health and Safety at Work Regulations Northern Ireland 2000Northern IrelandSeparate Northern Ireland risk assessment, coordination, emergency and competent-assistance route.; SR 2000/388, as amended
38HSENIHSENI machinery safety devices safety alertNorthern Ireland safety alertCurrent warning on bypassed safety devices; apply to the equipment and conditions within scope.; Published 4 March 2026; checked 23 September 2026
39HSEHSE Electrical safety at workGreat Britain guidanceSeparate electrical risk, isolation and competence route where applicable.; Current portal checked 23 September 2026
40HSENIHSENI Refurbished and modified machineryNorthern Ireland guidanceRefurbishment and modification boundaries, including possible manufacturer and product-supply consequences.; Publisher publication/update date not stated; current page checked 23 September 2026
41HSEHSE Training and competence for work equipmentGreat Britain guidanceTask- and person-specific competence; no generic certificate or expiry period.; Updated 6 June 2025; checked 23 September 2026
42HSENIHSENI Supplier, importer or hirer of equipmentNorthern Ireland product and hire guidanceDuties that can arise from supply, import or hire; separate from workplace-use control.; Publisher publication/update date not stated; current page checked 23 September 2026
43HSEHSE Pressure systemsGreat Britain guidanceSeparate pressure-systems route where applicable.; Current portal checked 23 September 2026
44HSEHSE Dangerous substances and explosive atmospheresGreat Britain guidanceSeparate dangerous-substance and explosive-atmosphere route where equipment can ignite or handle dangerous substances.; Updated 14 October 2024; checked 23 September 2026
45HSEHSE Mobile work equipmentGreat Britain guidanceAdditional mobile-equipment considerations; equipment-specific limits and permissions remain local.; Updated 29 October 2024; checked 23 September 2026
46HSEHSE INDG242 Control back-pain risks from whole-body vibrationGreat Britain sector guidanceMobile-machinery and whole-body-vibration context, not a generic PUWER design authority.; Revision 1, June 2005; retained copy inspected
47HSENIHSENI Working safely with farm equipment and vehiclesNorthern Ireland sector guidanceSector examples for guards, maintenance and safe use; transfer only where conditions match.; Publisher publication/update date not stated; current page checked 23 September 2026
48legislation.gov.ukHealth and Safety at Work etc Act 1974Great BritainGreat Britain foundation for safe plant, systems, information, training, supervision and protection of others.; 1974 c.37, as amended
49legislation.gov.ukHealth and Safety at Work Northern Ireland Order 1978Northern IrelandNorthern Ireland foundation for safe plant, systems, information, training, supervision and protection of others.; SI 1978/1039, as amended
50HSEHSE INDG474 Lifting equipment at workGreat Britain lifting guidanceCurrent brief LOLER guide; supersedes the withdrawn retained INDG290 and INDG422 leaflets.; Published April 2017; checked 23 September 2026
51HSEHSE Managing risk using PPEGreat BritainFive-level control hierarchy and PPE boundary; Current page; date not displayed
52HSEHSE Managing for health and safety (HSG65)Great BritainCurrent source at verification date; Live source; check the linked page for updates
Acronyms and terms

Table ID: work-equipment-lifting-equipment-and-pressure-systems-terms

Source: https://www.sharehub.ltd/knowledge-hub/work-equipment-lifting-equipment-and-pressure-systems.html

Row 1

Column 1

Work equipment

Column 2

Machinery, appliance, apparatus, tool or installation used at work.

Column 3

Scope depends on real use.

Row 2

Column 1

Guard

Column 2

Physical barrier preventing or restricting access to danger.

Column 3

Design is equipment specific.

Row 3

Column 1

Protection device

Column 2

Control or sensing function that reduces risk.

Column 3

Must not be bypassed.

Row 4

Column 1

Emergency stop

Column 2

Additional rapid stop function where appropriate.

Column 3

Not full isolation.

Row 5

Column 1

Isolation

Column 2

Separation and control of all relevant energy.

Column 3

Includes stored energy.

Row 6

Column 1

Inspection

Column 2

Competent check to detect safety-relevant deterioration or installation issues.

Column 3

Not the same as maintenance.

Row 7

Column 1

Quarantine

Column 2

State preventing further use pending decision.

Column 3

Release needs evidence and authority.

Row 8

Column 1

Return to service

Column 2

Recorded operational acceptance after restoration.

Column 3

Repair alone is insufficient.

Row 9

Column 1

PUWER

Column 2

Provision and Use of Work Equipment Regulations; separate GB and NI instruments.

Column 3

General workplace equipment duty route.

Row 10

Column 1

LOLER

Column 2

Lifting Operations and Lifting Equipment Regulations; separate GB and NI instruments.

Column 3

Planning, safe use, marking and thorough examination of lifting equipment.

Row 11

Column 1

PSSR

Column 2

Pressure Systems Safety Regulations; separate GB and NI instruments.

Column 3

Safe limits and written-scheme examination where applicable.

Row 12

Column 1

WSE

Column 2

Written scheme of examination for qualifying pressure systems.

Column 3

A competent person defines the parts, nature and frequency of examination.

Row 13

Column 1

SWL

Column 2

Safe working load.

Column 3

Check the actual equipment configuration and marked limit.

Row 14

Column 1

ACOP

Column 2

Approved Code of Practice.

Column 3

Check approved edition and jurisdiction.

Row 15

Column 1

ERICPD

Column 2

Eliminate, Reduce including substitution, Isolate, Control, personal protective equipment, Discipline.

Column 3

A SHARE decision prompt; sustain effective controls and learning.

Row 16

Column 1

PPE

Column 2

Personal protective equipment.

Column 3

Use for assessed residual exposure; it does not replace stronger feasible controls.

Read the complete comparison table
Acronyms and terms
RowColumn 1Column 2Column 3
1Work equipmentMachinery, appliance, apparatus, tool or installation used at work.Scope depends on real use.
2GuardPhysical barrier preventing or restricting access to danger.Design is equipment specific.
3Protection deviceControl or sensing function that reduces risk.Must not be bypassed.
4Emergency stopAdditional rapid stop function where appropriate.Not full isolation.
5IsolationSeparation and control of all relevant energy.Includes stored energy.
6InspectionCompetent check to detect safety-relevant deterioration or installation issues.Not the same as maintenance.
7QuarantineState preventing further use pending decision.Release needs evidence and authority.
8Return to serviceRecorded operational acceptance after restoration.Repair alone is insufficient.
9PUWERProvision and Use of Work Equipment Regulations; separate GB and NI instruments.General workplace equipment duty route.
10LOLERLifting Operations and Lifting Equipment Regulations; separate GB and NI instruments.Planning, safe use, marking and thorough examination of lifting equipment.
11PSSRPressure Systems Safety Regulations; separate GB and NI instruments.Safe limits and written-scheme examination where applicable.
12WSEWritten scheme of examination for qualifying pressure systems.A competent person defines the parts, nature and frequency of examination.
13SWLSafe working load.Check the actual equipment configuration and marked limit.
14ACOPApproved Code of Practice.Check approved edition and jurisdiction.
15ERICPDEliminate, Reduce including substitution, Isolate, Control, personal protective equipment, Discipline.A SHARE decision prompt; sustain effective controls and learning.
16PPEPersonal protective equipment.Use for assessed residual exposure; it does not replace stronger feasible controls.