Competence, induction and effective supervision · detailed source study
Optional reference study from the SHAREhub topic pages and selected source records used for this course. The core learning-time estimate excludes this extended reference.
Adjust supervision to task novelty and demonstrated performance
Adjust supervision to task novelty and demonstrated performance
Source: competence-training-information-and-supervision--review-start
Compare three people before assigning unsupervised work. A new worker needs instruction, supported practice and observed performance. An experienced worker on changed equipment needs assessment of what has changed, not an assumption of transfer. A specialist contractor needs demonstrated capability plus the unfamiliar site’s hazards and interfaces. Compare three people before assigning unsupervised work. A new worker needs instruction, supported practice and observed performance. Start with the real task and its failure consequences. Apply it: Which part of this plan would you check at the workface before authorising the task? Start with the real task and its failure consequences. Define the capability needed, give clear information and practice, observe performance, authorise only within limits and supervise according to risk.
If an incident, near miss or poor audit finding occurs, the investigation asks whether the issue came from training, unclear instruction, weak supervision, poor work design or management pressure. Apply it: What evidence would show that the change improves this task, rather than only completing a record? The business then builds a competence matrix that links roles to training needs, practical assessments, refresher dates and supervision levels. New starters and apprentices are placed under close supervision until they have completed induction, task briefings and observed assessments. Site managers review competence before allocating high-risk tasks, and the system prevents expired authorisations being treated as current. the site team also manages contractors through procurement and site control.
Apply it: At which point would you hold this example, and what evidence would allow it to proceed? Attendance used as proof: People may not be able to perform the task safely. Generic induction: Workers miss site-specific hazards and controls. Expired or missing refreshers: Rare or changed tasks are performed from memory. Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby? Eliminate: Avoid the lift through design or off-site assembly where feasible. Substitute: Use smaller preassembled units or lower-energy method after checking new handling risks. Engineering: Rated lifting equipment plus physical public exclusion and load path separation. Administrative: Lift plan, observed signaller competence, briefing and communication. PPE: Helmets and other task PPE for residual risk only.
Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged. Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk? Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status. Apply it: Which official source and full-topic section will you use to resolve the next decision? Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page.
Read the full topic for explanations, questions and source links. Compare three people before assigning unsupervised work. Compare three people before assigning unsupervised work. A new worker needs instruction, supported practice and observed performance. Start with the real task and its failure consequences. Apply it: Which part of this plan would you check at the workface before authorising the task? Use the evidence to improve the actual work arrangement. Start with the real task and its failure consequences. Define the capability needed, give clear information and practice, observe performance, authorise only within limits and supervise according to risk.
If an incident, near miss or poor audit finding occurs, the investigation asks whether the issue came from training, unclear instruction, weak supervision, poor work design or management pressure. Apply it: What evidence would show that the change improves this task, rather than only completing a record? Fictional example: a practical application of the existing topic lesson. The business then builds a competence matrix that links roles to training needs, practical assessments, refresher dates and supervision levels. New starters and apprentices are placed under close supervision until they have completed induction, task briefings and observed assessments. Site managers review competence before allocating high-risk tasks, and the system prevents expired authorisations being treated as current. the site team also manages contractors through procurement and site control.
Apply it: At which point would you hold this example, and what evidence would allow it to proceed? Connect the task, the route to the person and the control that can fail. Attendance used as proof: People may not be able to perform the task safely. Generic induction: Workers miss site-specific hazards and controls. Expired or missing refreshers: Rare or changed tasks are performed from memory. Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby? Start with the stronger practicable options and verify their effect. Eliminate: Avoid the lift through design or off-site assembly where feasible. Substitute: Use smaller preassembled units or lower-energy method after checking new handling risks.
Engineering: Rated lifting equipment plus physical public exclusion and load path separation. Administrative: Lift plan, observed signaller competence, briefing and communication. PPE: Helmets and other task PPE for residual risk only. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged. Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk? Follow the official sources below and retain the task-specific evidence. Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction.
A simplified guide does not change the page’s technical-review or approval status. Apply it: Which official source and full-topic section will you use to resolve the next decision? Simplified learning guide. Use the full topic and the actual work arrangements; existing technical-review and approval statuses still apply. Workplace scenarios labelled fictional are illustrative examples. Agree who assesses each person, what they must demonstrate, what remains outside their authority and when supervision can change. Training attendance and certificates inform the decision but cannot replace observation and a task-specific release. Use the specialist process-safety competence guide where the role protects critical barriers; do not copy its detailed authority model indiscriminately to every low-risk task. Illustrative example.
A fictional experienced worker is assigned equipment with different controls and isolation arrangements. Decision. The supervisor identifies the differences, provides instruction and supervised practice, and has an accountable assessor observe the required performance. Evidence to check. Task criteria, instruction, observed safe operation, stop/escalation knowledge and recorded supervision limits. Hold or escalation point. No unsupervised release while critical changed features have not been demonstrated. Follow-up. Review performance in use and after further changes, defects or indications that the instruction is unclear. Read with: HSE supervision guide.
Adjust supervision to the task and the evidence
Adjust supervision to the task and the evidence
An experienced worker can still be new to the site, equipment or changed task. Match support to what has actually been observed. Distinguish familiarity with this exact task from training elsewhere or experience on a different process. Check understanding and observed application in the current conditions; identify what remains untested. Agree supervision, practice and the authorisation route. Reassess after meaningful change rather than award an automatic score. Experience and a certificate are inputs to the decision, not universal task permission. Further guidance: HSE: managing health and safety.
What are the key points about competence, training, information and supervision?
Source: competence-training-information-and-supervision--key-points
The key points are that competence is role-specific, risk-based, assessed in context, supported by supervision and reviewed when evidence changes.
What does competence, training, information and supervision mean?
Source: competence-training-information-and-supervision--what-is-it
It means making sure people receive the right knowledge, instruction, practice, support and oversight to perform work safely and reliably. Competence is best understood as applied capability. A person may have attended training, but the real test is whether they can recognise the hazards, select the right controls, follow or adapt the safe system appropriately, communicate uncertainty and know when to stop. This is why competence must be connected to the actual role, task, workplace and risk profile. Training is one route to competence, but it is not the whole system. Information tells people what they need to know. Instruction tells them how to act. Training develops knowledge and skill. Supervision checks, supports and corrects performance.
Assessment verifies whether the person can perform the task to the required standard. Review keeps competence current as work changes. A strong competence system is deliberate. It defines roles, identifies safety-critical tasks, analyses training needs, chooses suitable training methods, appoints competent trainers, assesses learning, records evidence, provides supervision, manages contractors and refreshes competence when there is change, drift or learning from events.
What does a usable competence model contain?
Source: competence-training-information-and-supervision--competence-model
Define a task standard, assessment method, authorisation limit, supervisor and review trigger for each risk-critical task. The HSE competence guide distinguishes training from demonstrated capability. For a mobile-plant operator, the standard should cover pre-use checks, pedestrian separation, load limits, a failed warning device and a safe stop. A competent assessor observes the actual task and tests rare abnormal decisions through a scenario. Record the equipment and work conditions covered by authorisation, plus restrictions. Reassess after changed plant or method, a near miss, poor observation or extended absence; do not infer competence from attendance or tenure.
How should training needs analysis be carried out?
How should training needs analysis be carried out?
Source: competence-training-information-and-supervision--tna
Training needs analysis should compare what the role requires with the person's current capability and the risk of getting the work wrong. Training needs analysis should begin with work, not with a catalogue of courses. The organisation should identify tasks, hazards, legal requirements, equipment, substances, people affected, emergency demands, previous incidents, changes and contractor interfaces. It then decides what each role needs to know and do. A useful analysis separates awareness from task competence. Everyone may need basic awareness of reporting routes and emergency arrangements. Only selected people may need detailed competence for abrasive wheels, forklift operations, confined spaces, asbestos awareness, permits, chemical handling, first aid, incident investigation or fire warden duties.
Supervisors and managers need additional capability to plan work, check controls and act on weak signals.
How should information and instruction be designed?
Source: competence-training-information-and-supervision--information-instruction
Information and instruction should be clear enough for the audience to understand and practical enough to use at the point of work. Information answers what people need to know. Instruction answers what people need to do. Both should be written and delivered for the audience: experience level, language, literacy, working pattern, access to technology, supervision level and task risk. A technically correct instruction can still fail if it is too long, too abstract, hidden in a folder or delivered after the work has already started. Good information and instruction use plain English, diagrams or photographs where helpful, current versions, clear ownership and defined stop-work points. For high-risk work, instructions should avoid relying on memory alone.
The critical steps should be briefed, visible, checked and built into permits, checklists or point-of-work prompts.
Which training methods should be used?
Source: competence-training-information-and-supervision--training-methods
Training methods should match the task risk, learning outcome, audience, available evidence and need for practical assessment. Short online awareness can be suitable for basic topics, but it is not enough for tasks where poor performance could cause serious harm. Practical skills normally need demonstration, supervised practice and assessment. Complex or safety-critical work may need classroom learning, simulation, scenario exercises, mentored experience, formal assessment and periodic reassessment. The trainer also needs competence. A good trainer understands the task, hazards, controls, common errors, learning method and assessment standard. In-house training can be suitable where the organisation has competent people and enough structure. External training may be needed where the subject is specialist, legally prescribed, high-risk or better served by recognised industry schemes.
How should supervision control risk?
How should supervision control risk?
Source: competence-training-information-and-supervision--supervision
Supervision checks the work conditions, capability and controls before and during the task, and intervenes when they drift. The HSE supervision guide calls for suitable oversight of workers and contractors. A new operator may need close observation; an experienced person may need periodic sampling, but a changed plant or non-routine isolation requires renewed direct checks. The supervisor should verify the method, access, guard, permit and rescue resources where relevant, invite questions and stop work if an essential control fails. “Supervised” is not a substitute for an authorised, competent person on a task the supervisor cannot oversee effectively.
How should competence assurance work?
Source: competence-training-information-and-supervision--assurance
Competence assurance should prove that people can perform the required work to the required standard and that the system remains reliable. Assurance should not stop at attendance records. It should ask whether the person can explain the risks, demonstrate the control, make good decisions under foreseeable conditions and recognise limits. For safety-critical roles, assurance should be stronger and more formal because the consequences of error are higher. The evidence should be proportionate and current. A competence matrix is useful only if it is connected to real tasks, expiry dates, assessment evidence, supervision arrangements and change control. Assurance should also look for organisational weaknesses: unavailable trainers, overdue refreshers, poor contractor checks, rushed inductions, weak supervision or managers without the competence to challenge unsafe work.
When should refresher training and reassessment be used?
Source: competence-training-information-and-supervision--refresher
Refresher training and reassessment should be used when competence may decay, conditions change or evidence shows that performance is drifting. Competence is not permanent. People forget rarely used procedures, habits drift, equipment changes, regulations change, work pressure changes and people may return after long absence. Refresher training should be planned for infrequent, complex or safety-critical tasks and triggered by change, incident learning, audit findings or poor performance. Refreshers should not simply repeat old slides. They should focus on what has changed, what people have forgotten, what incidents show, which errors are most likely and what performance standard must be demonstrated. Where the task is safety-critical, reassessment may be needed before the person is authorised again.
How should organisational competence be managed?
How should organisational competence be managed?
Source: competence-training-information-and-supervision--organisational
Organisational competence means the business has enough capable people, systems and specialist support to understand and control its risk profile. An organisation can have trained individuals and still lack organisational competence. This happens when knowledge sits with one person, supervisors are overloaded, managers cannot challenge specialist advice, contractor work is outsourced without intelligent oversight, or senior leaders do not understand the risk implications of decisions. Organisational competence should cover leadership, technical authority, supervision, worker capability, emergency response, contractor control, procurement, maintenance, occupational health, human factors and the ability to obtain specialist advice when needed. It should also protect corporate memory so competence is not lost when experienced people leave.
How should contractor competence be controlled?
Source: competence-training-information-and-supervision--contractors
Contractor competence should be checked before appointment, briefed before work, supervised during work and reviewed after completion. Contractor competence is not proved by asking for a generic policy or training certificate. The host organisation should define the work, the hazards, the expected competence, the interface with site operations, the supervision arrangements and the evidence required. Higher-risk work needs stronger checks and closer coordination. A good contractor process covers selection, prequalification, method review, site induction, permit briefings, named supervision, monitoring, stop-work rules, change communication, incident reporting and post-job review. Where specialist work is outsourced, the client still needs enough competence to understand the advice, challenge assumptions and verify that the work is controlled.
How can the ISO 45001 hierarchy of controls reduce risk before relying on training and supervision?
Source: competence-training-information-and-supervision--safety-critical
Map each serious-harm scenario to the human task and engineered barrier, then test both under normal and abnormal conditions. For a lift near a public route, first ask if the lift can be avoided or prefabricated elsewhere. Reduce load and exposure where practical, isolate pedestrians with a designed exclusion zone and suitable barriers, then use an assessed lifting plan, competent signaller and supervision. PPE deals only with residual exposure. This ERICPD sequence maps to the five-level hierarchy: elimination, substitution, engineering, administrative and PPE. The lift supervisor owns the boundary; the competent lifting person checks equipment and capacity; the site supervisor verifies exclusion and stops the lift if a person enters the zone or a control fails. ERICPD is a planning crossmap.
Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level. The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation"). ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance. HSE’s five-level hierarchy is the GB framework for elimination, substitution, engineering, administrative controls and PPE. ERICPD is complementary. Select measures for the actual hazard and work location, then verify physical and human controls separately. For this lift, the competent planner checks the actual load, equipment/accessories, route, ground/support conditions, nearby services and physical exclusion before authorising the method.
HSE lifting planning guidance supports this task-specific approach. Installation/assembly acceptance and required competent examination must precede use; the operator’s pre-use checks and planned maintenance/inspection continue afterwards. HSE examination guidance distinguishes these checks and cautions that routine overload testing is not always needed. The lift supervisor stops on a defect, lost signal or intrusion, then requires correction and the appropriate technical verification before recording restart authority. An observed signaller assessment is an administrative check, not proof of equipment or boundary integrity.
What evidence shows competence arrangements are working?
What evidence shows competence arrangements are working?
Source: competence-training-information-and-supervision--evidence
Evidence should show that competence requirements were defined, learning was delivered, understanding was checked and performance was verified in the workplace. The best evidence is connected to risk. A training matrix should trace back to roles and hazards. Assessment records should show the standard tested. Supervision records should show real findings. Incident investigations should ask whether competence, instruction or supervision contributed. Audits should sample the workplace, not just the database. Good evidence also shows improvement. If a supervision check identifies poor isolation practice, the organisation should record the finding, correct the immediate issue, check whether training or procedure design contributed, brief affected teams, verify improvement and review whether the same issue exists elsewhere.
Which duties apply in Great Britain and Northern Ireland?
Source: competence-training-information-and-supervision--legal
Both require suitable information, instruction, training and supervision, but select the instrument and regulator for the work location. In GB, the Health and Safety at Work etc. Act 1974, Management Regulations 1999 and task-specific rules such as PUWER may apply. HSE equipment guidance explains training for equipment users and supervisors. In NI, the 1978 Health and Safety Order and Management Regulations (NI) 2000 provide the local route; HSENI competent-person guidance addresses knowledge, skills and experience. A course or generic competence card does not replace task and site assessment. Construction work needs its own dutyholder and project checks; take competent local advice for a live legal decision.
How could BuildOut Ltd manage competence, training, information and supervision?
Source: competence-training-information-and-supervision--business-example
BuildOut Ltd would manage competence through role profiles, task risk, training needs, supervision plans, contractor checks and evidence-led review. A fictional construction and refurbishment contractor delivering fit-out, maintenance, civils, small demolition, plant operations, subcontracted specialist work and multi-site projects. BuildOut starts by mapping its work: site management, temporary works coordination, plant operation, abrasive wheels, work at height, excavation, lifting, hot works, asbestos awareness, silica dust controls, electrical isolation, manual handling, traffic management, first aid, fire, contractor coordination and emergency response. Each task is given a risk rating and a competence standard. The business then builds a competence matrix that links roles to training needs, practical assessments, refresher dates and supervision levels.
New starters and apprentices are placed under close supervision until they have completed induction, task briefings and observed assessments. Site managers review competence before allocating high-risk tasks, and the system prevents expired authorisations being treated as current. BuildOut also manages contractors through procurement and site control. Specialist subcontractors must provide evidence relevant to the work, but BuildOut still briefs site rules, checks the work area, monitors performance and reviews learning afterwards. If an incident, near miss or poor audit finding occurs, the investigation asks whether the issue came from training, unclear instruction, weak supervision, poor work design or management pressure.
What should each role learn and demonstrate?
What should each role learn and demonstrate?
Source: competence-training-information-and-supervision--training
Learning must match the decisions people make, from recognising danger to checking that controls work. Briefings should tell people how to act, but attendance alone does not show competence. Assess the real decision or task, record who assessed it and revisit after a material change, failed control or incident. A local authorisation is task-specific; no universal external certificate is implied.
How can this topic support advanced safety study?
Source: competence-training-information-and-supervision--nebosh
This topic supports advanced safety study by helping learners assess, develop and maintain individual and organisational health and safety competence. For Diploma study, a strong answer should define competence, explain why training alone is insufficient, link competence to risk assessment, describe training needs analysis, distinguish information from instruction, explain supervision as a control and identify evidence that the competence system is working. Scenario answers should be specific. If a worker makes an error during a high-risk task, do not jump straight to retraining. Ask whether the task was designed well, whether instructions were clear, whether the person was authorised, whether supervision was adequate, whether workload or fatigue affected performance, whether change was briefed and whether competence was reassessed after previous findings.
How can a management system sustain effective decisions?
Source: competence-training-information-and-supervision--management-system
Give each hazard or support route an owner, a control, a check and a response to failure. Keep task standards, information, training, supervision, authorisation and incident feedback linked to named owners. Check practice in the work area, not course completions. An owner should sample actual work and corrective actions, not accept a policy or certificate as evidence that the controls work. The free GB regulator guide HSE Managing for health and safety (HSG65) explains a plan–do–check–act approach: assign controls and owners, involve workers, check work as done, and correct failures. For Northern Ireland, use HSENI risk assessment guidance for the local duty. A certificate alone does not demonstrate that a control works.
What warning signs show competence arrangements are weak?
Source: competence-training-information-and-supervision--warning-signs
Warning signs include training records with no task link, expired authorisations, weak supervision, repeated errors, contractor confusion and people unable to explain critical controls. Weak competence systems usually show up before a serious incident. People may be allocated tasks because they are available rather than competent. Supervisors may be responsible for checking work they do not understand. Contractors may be trusted because they supplied generic paperwork. Training may be refreshed by time interval only, not by risk, change or performance. These warning signs should trigger system review, not only individual retraining. The organisation should check role profiles, workload, procedure design, supervision levels, training quality, assessment standard, change communication and whether leaders are giving people enough time and resources to work competently.
Source tables and records 1
Competence, training, information and supervision explained
Table ID: competence-training-information-and-supervision-competence-training-information-and-supervision-explained
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Element
Competence
- What it means
Applied knowledge, skill, experience and behaviour in the real task and conditions.
- Common weakness
Treating a certificate as permanent proof.
Row 2
- Element
Information
- What it means
Facts people need, such as risks, rules, contacts, emergency actions and arrangements.
- Common weakness
Providing too much information in inaccessible documents.
Row 3
- Element
Instruction
- What it means
Clear direction on what to do, what not to do and when to escalate.
- Common weakness
Using vague wording such as 'take care' or 'be sensible'.
Row 4
- Element
Training
- What it means
Planned learning that develops knowledge, skill and confidence.
- Common weakness
Delivering generic training unrelated to the task.
Row 5
- Element
Supervision
- What it means
Oversight, coaching, checking and intervention proportionate to risk.
- Common weakness
Assuming experienced people need no supervision.
Row 6
- Element
Assurance
- What it means
Evidence that competence exists and remains suitable.
- Common weakness
Keeping attendance sheets but not observing performance.
Read the complete comparison table
| Row | Element | What it means | Common weakness |
|---|---|---|---|
| 1 | Competence | Applied knowledge, skill, experience and behaviour in the real task and conditions. | Treating a certificate as permanent proof. |
| 2 | Information | Facts people need, such as risks, rules, contacts, emergency actions and arrangements. | Providing too much information in inaccessible documents. |
| 3 | Instruction | Clear direction on what to do, what not to do and when to escalate. | Using vague wording such as 'take care' or 'be sensible'. |
| 4 | Training | Planned learning that develops knowledge, skill and confidence. | Delivering generic training unrelated to the task. |
| 5 | Supervision | Oversight, coaching, checking and intervention proportionate to risk. | Assuming experienced people need no supervision. |
| 6 | Assurance | Evidence that competence exists and remains suitable. | Keeping attendance sheets but not observing performance. |
Task-specific competence record
Table ID: competence-training-information-and-supervision-model
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Column-1
Task and hazard
- Column-2
Define plant, people, failure consequence and control.
- Column-3
Assessor checks real task; no assignment if scope is unclear.
Row 2
- Column-1
Training and practice
- Column-2
Explain and rehearse normal and abnormal work.
- Column-3
Trainer records practice; stop if key control cannot be explained.
Row 3
- Column-1
Observed assessment
- Column-2
Test safe set-up, control use and response to failure.
- Column-3
Competent assessor signs result and limits.
Row 4
- Column-1
Authorisation and supervision
- Column-2
Name person, permitted task and supervisor.
- Column-3
Supervisor checks currency before allocation.
Row 5
- Column-1
Review
- Column-2
Trigger on change, near miss, absence or failed check.
- Column-3
Restrict task until reassessed and reauthorised.
Read the complete comparison table
| Row | Column-1 | Column-2 | Column-3 |
|---|---|---|---|
| 1 | Task and hazard | Define plant, people, failure consequence and control. | Assessor checks real task; no assignment if scope is unclear. |
| 2 | Training and practice | Explain and rehearse normal and abnormal work. | Trainer records practice; stop if key control cannot be explained. |
| 3 | Observed assessment | Test safe set-up, control use and response to failure. | Competent assessor signs result and limits. |
| 4 | Authorisation and supervision | Name person, permitted task and supervisor. | Supervisor checks currency before allocation. |
| 5 | Review | Trigger on change, near miss, absence or failed check. | Restrict task until reassessed and reauthorised. |
Training needs analysis process
Table ID: competence-training-information-and-supervision-training-needs-analysis-process
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Step
Define roles and tasks
- What to consider
Who does what, where and under whose control?
- Output
Role and task matrix.
Row 2
- Step
Identify risk and legal needs
- What to consider
What hazards, regulations, standards and emergency duties apply?
- Output
Risk-linked training requirements.
Row 3
- Step
Assess current capability
- What to consider
What evidence shows knowledge, skill and experience now?
- Output
Gap analysis and priority list.
Row 4
- Step
Select learning method
- What to consider
Does the need require awareness, instruction, coaching, practical assessment or specialist training?
- Output
Training plan and delivery method.
Row 5
- Step
Prioritise
- What to consider
Which gaps create the highest risk or legal exposure?
- Output
Action plan with owners and dates.
Row 6
- Step
Review
- What to consider
What will trigger update?
- Output
Review schedule and change triggers.
Read the complete comparison table
| Row | Step | What to consider | Output |
|---|---|---|---|
| 1 | Define roles and tasks | Who does what, where and under whose control? | Role and task matrix. |
| 2 | Identify risk and legal needs | What hazards, regulations, standards and emergency duties apply? | Risk-linked training requirements. |
| 3 | Assess current capability | What evidence shows knowledge, skill and experience now? | Gap analysis and priority list. |
| 4 | Select learning method | Does the need require awareness, instruction, coaching, practical assessment or specialist training? | Training plan and delivery method. |
| 5 | Prioritise | Which gaps create the highest risk or legal exposure? | Action plan with owners and dates. |
| 6 | Review | What will trigger update? | Review schedule and change triggers. |
Information and instruction design
Table ID: competence-training-information-and-supervision-information-and-instruction-design
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Design issue
Plain language
- Good practice
Use direct wording and explain acronyms.
- Evidence
Worker feedback and understanding checks.
Row 2
- Design issue
Task relevance
- Good practice
Link instructions to the actual work, equipment and location.
- Evidence
Task briefing and procedure review.
Row 3
- Design issue
Accessibility
- Good practice
Make information available when and where it is needed.
- Evidence
Controlled document access and site display.
Row 4
- Design issue
Critical steps
- Good practice
Highlight steps where error could cause serious harm.
- Evidence
Checklists, permits and supervisor verification.
Row 5
- Design issue
Change control
- Good practice
Remove old versions and brief changes before use.
- Evidence
Version control and change briefing records.
Row 6
- Design issue
Feedback route
- Good practice
Let workers challenge instructions that do not match real work.
- Evidence
Procedure feedback and action close-out.
Read the complete comparison table
| Row | Design issue | Good practice | Evidence |
|---|---|---|---|
| 1 | Plain language | Use direct wording and explain acronyms. | Worker feedback and understanding checks. |
| 2 | Task relevance | Link instructions to the actual work, equipment and location. | Task briefing and procedure review. |
| 3 | Accessibility | Make information available when and where it is needed. | Controlled document access and site display. |
| 4 | Critical steps | Highlight steps where error could cause serious harm. | Checklists, permits and supervisor verification. |
| 5 | Change control | Remove old versions and brief changes before use. | Version control and change briefing records. |
| 6 | Feedback route | Let workers challenge instructions that do not match real work. | Procedure feedback and action close-out. |
Training methods and best use
Table ID: competence-training-information-and-supervision-training-methods-and-best-use
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Method
Awareness briefing or e-learning
- Best use
Basic understanding, induction and broad policy messages.
- Limitations
Weak for practical competence unless followed by assessment.
Row 2
- Method
Face-to-face course
- Best use
Discussion, case examples, questions and shared learning.
- Limitations
Needs competent delivery and workplace follow-up.
Row 3
- Method
Demonstration
- Best use
Showing how equipment, controls or safe systems work.
- Limitations
Needs supervised practice afterwards.
Row 4
- Method
On-the-job training
- Best use
Building skill in the real work environment.
- Limitations
Must be structured and linked to risk assessment.
Row 5
- Method
Simulation or drill
- Best use
Emergency, infrequent or complex safety-critical tasks.
- Limitations
Needs realistic scenarios and debrief.
Row 6
- Method
Formal assessment
- Best use
Authorising people for defined tasks.
- Limitations
Must test actual performance, not just attendance.
Read the complete comparison table
| Row | Method | Best use | Limitations |
|---|---|---|---|
| 1 | Awareness briefing or e-learning | Basic understanding, induction and broad policy messages. | Weak for practical competence unless followed by assessment. |
| 2 | Face-to-face course | Discussion, case examples, questions and shared learning. | Needs competent delivery and workplace follow-up. |
| 3 | Demonstration | Showing how equipment, controls or safe systems work. | Needs supervised practice afterwards. |
| 4 | On-the-job training | Building skill in the real work environment. | Must be structured and linked to risk assessment. |
| 5 | Simulation or drill | Emergency, infrequent or complex safety-critical tasks. | Needs realistic scenarios and debrief. |
| 6 | Formal assessment | Authorising people for defined tasks. | Must test actual performance, not just attendance. |
Competence assurance evidence
Table ID: competence-training-information-and-supervision-competence-assurance-evidence
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Evidence
Competence matrix
- What it proves
Who is authorised for which tasks.
- What to watch for
Out-of-date roles or blanket sign-offs.
Row 2
- Evidence
Observed assessment
- What it proves
Person can perform the task in practice.
- What to watch for
Assessments that do not cover abnormal conditions.
Row 3
- Evidence
Questioning
- What it proves
Person understands why controls matter.
- What to watch for
Questions that only test memory.
Row 4
- Evidence
Supervisor verification
- What it proves
Work is being performed correctly over time.
- What to watch for
Supervision records with no findings or coaching.
Row 5
- Evidence
Incident and near-miss review
- What it proves
Competence gaps may have contributed.
- What to watch for
Blaming individuals without checking system causes.
Row 6
- Evidence
Audit sampling
- What it proves
The competence system works across teams and sites.
- What to watch for
Sampling only records and not field performance.
Read the complete comparison table
| Row | Evidence | What it proves | What to watch for |
|---|---|---|---|
| 1 | Competence matrix | Who is authorised for which tasks. | Out-of-date roles or blanket sign-offs. |
| 2 | Observed assessment | Person can perform the task in practice. | Assessments that do not cover abnormal conditions. |
| 3 | Questioning | Person understands why controls matter. | Questions that only test memory. |
| 4 | Supervisor verification | Work is being performed correctly over time. | Supervision records with no findings or coaching. |
| 5 | Incident and near-miss review | Competence gaps may have contributed. | Blaming individuals without checking system causes. |
| 6 | Audit sampling | The competence system works across teams and sites. | Sampling only records and not field performance. |
Refresher triggers
Table ID: competence-training-information-and-supervision-refresher-triggers
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Trigger
Time interval
- Why it matters
Knowledge and skill can fade.
- Typical action
Scheduled refresher or reassessment.
Row 2
- Trigger
Infrequent task
- Why it matters
People may not practise enough to remain confident.
- Typical action
Pre-task briefing and supervised practice.
Row 3
- Trigger
Equipment or process change
- Why it matters
Old competence may no longer match the task.
- Typical action
Change briefing, training and updated assessment.
Row 4
- Trigger
Incident or near miss
- Why it matters
Learning may reveal a competence gap.
- Typical action
Targeted refresher and system review.
Row 5
- Trigger
Audit or observation finding
- Why it matters
Work as done may differ from the standard.
- Typical action
Coaching, retraining or revised supervision.
Row 6
- Trigger
Return after absence
- Why it matters
Familiarity and confidence may have reduced.
- Typical action
Reinduction and supervised restart.
Read the complete comparison table
| Row | Trigger | Why it matters | Typical action |
|---|---|---|---|
| 1 | Time interval | Knowledge and skill can fade. | Scheduled refresher or reassessment. |
| 2 | Infrequent task | People may not practise enough to remain confident. | Pre-task briefing and supervised practice. |
| 3 | Equipment or process change | Old competence may no longer match the task. | Change briefing, training and updated assessment. |
| 4 | Incident or near miss | Learning may reveal a competence gap. | Targeted refresher and system review. |
| 5 | Audit or observation finding | Work as done may differ from the standard. | Coaching, retraining or revised supervision. |
| 6 | Return after absence | Familiarity and confidence may have reduced. | Reinduction and supervised restart. |
Organisational competence controls
Table ID: competence-training-information-and-supervision-organisational-competence-controls
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Control
Competence strategy
- Why it matters
Sets expectations for roles, risk and assurance.
- Evidence
Approved framework and review process.
Row 2
- Control
Technical authority
- Why it matters
Ensures specialist decisions are made by suitable people.
- Evidence
Named competent persons and escalation route.
Row 3
- Control
Succession planning
- Why it matters
Reduces dependence on one experienced person.
- Evidence
Deputies, mentoring and knowledge transfer.
Row 4
- Control
Contractor oversight
- Why it matters
Retains intelligent customer capability.
- Evidence
Contractor review, audit and performance meetings.
Row 5
- Control
Management review
- Why it matters
Tests whether competence arrangements remain suitable.
- Evidence
Senior review of gaps, incidents, audit and resources.
Row 6
- Control
Specialist help
- Why it matters
Recognises limits of internal knowledge.
- Evidence
Documented brief, advice, decision and action close-out.
Read the complete comparison table
| Row | Control | Why it matters | Evidence |
|---|---|---|---|
| 1 | Competence strategy | Sets expectations for roles, risk and assurance. | Approved framework and review process. |
| 2 | Technical authority | Ensures specialist decisions are made by suitable people. | Named competent persons and escalation route. |
| 3 | Succession planning | Reduces dependence on one experienced person. | Deputies, mentoring and knowledge transfer. |
| 4 | Contractor oversight | Retains intelligent customer capability. | Contractor review, audit and performance meetings. |
| 5 | Management review | Tests whether competence arrangements remain suitable. | Senior review of gaps, incidents, audit and resources. |
| 6 | Specialist help | Recognises limits of internal knowledge. | Documented brief, advice, decision and action close-out. |
Contractor competence checks
Table ID: competence-training-information-and-supervision-contractor-competence-checks
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Stage
Selection
- What to check
Relevant experience, competence, supervision and risk controls.
- Evidence
Prequalification, references and examples of similar work.
Row 2
- Stage
Planning
- What to check
Method, equipment, people, interfaces and emergency arrangements.
- Evidence
RAMS, permits, programme and coordination meeting.
Row 3
- Stage
Induction
- What to check
Site-specific hazards, rules, welfare and reporting.
- Evidence
Induction record and understanding check.
Row 4
- Stage
During work
- What to check
Work follows agreed controls and changes are authorised.
- Evidence
Supervisor observation, permit checks and issue log.
Row 5
- Stage
Completion
- What to check
Performance, incidents, defects and learning.
- Evidence
Post-job review and contractor scorecard.
Read the complete comparison table
| Row | Stage | What to check | Evidence |
|---|---|---|---|
| 1 | Selection | Relevant experience, competence, supervision and risk controls. | Prequalification, references and examples of similar work. |
| 2 | Planning | Method, equipment, people, interfaces and emergency arrangements. | RAMS, permits, programme and coordination meeting. |
| 3 | Induction | Site-specific hazards, rules, welfare and reporting. | Induction record and understanding check. |
| 4 | During work | Work follows agreed controls and changes are authorised. | Supervisor observation, permit checks and issue log. |
| 5 | Completion | Performance, incidents, defects and learning. | Post-job review and contractor scorecard. |
Worked lift control hierarchy
Table ID: competence-training-information-and-supervision-hierarchy
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Column-1
Eliminate / eliminate
- Column-2
Avoid the lift through design or off-site assembly where feasible.
- Column-3
Planner documents method; hold if route is not assessed.
Row 2
- Column-1
Substitute / reduce
- Column-2
Use smaller preassembled units or lower-energy method after checking new handling risks.
- Column-3
Lifting lead approves change and limit.
Row 3
- Column-1
Engineering / isolate and control
- Column-2
Rated lifting equipment plus physical public exclusion and load path separation.
- Column-3
Competent examiner and site lead verify test, inspection and barrier; stop on defect or intrusion.
Row 4
- Column-1
Administrative / discipline
- Column-2
Lift plan, observed signaller competence, briefing and communication.
- Column-3
Lift supervisor checks roles and weather; stop on lost signal.
Row 5
- Column-1
PPE / PPE
- Column-2
Helmets and other task PPE for residual risk only.
- Column-3
Supervisor checks fit and use; PPE never permits a failed exclusion.
Read the complete comparison table
| Row | Column-1 | Column-2 | Column-3 |
|---|---|---|---|
| 1 | Eliminate / eliminate | Avoid the lift through design or off-site assembly where feasible. | Planner documents method; hold if route is not assessed. |
| 2 | Substitute / reduce | Use smaller preassembled units or lower-energy method after checking new handling risks. | Lifting lead approves change and limit. |
| 3 | Engineering / isolate and control | Rated lifting equipment plus physical public exclusion and load path separation. | Competent examiner and site lead verify test, inspection and barrier; stop on defect or intrusion. |
| 4 | Administrative / discipline | Lift plan, observed signaller competence, briefing and communication. | Lift supervisor checks roles and weather; stop on lost signal. |
| 5 | PPE / PPE | Helmets and other task PPE for residual risk only. | Supervisor checks fit and use; PPE never permits a failed exclusion. |
Evidence and assurance checks
Table ID: competence-training-information-and-supervision-evidence-and-assurance-checks
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Evidence
Training matrix
- Strong use
Shows role-based requirements, status and expiry.
- Weak use
Lists courses without role or risk link.
Row 2
- Evidence
Assessment record
- Strong use
Shows practical performance against criteria.
- Weak use
Only records attendance.
Row 3
- Evidence
Supervisor check
- Strong use
Shows observation, coaching and correction.
- Weak use
Tick-box with no comments or action.
Row 4
- Evidence
Training evaluation
- Strong use
Checks whether learning changed performance.
- Weak use
Asks only whether people enjoyed the course.
Row 5
- Evidence
Audit
- Strong use
Samples documents, interviews and work as done.
- Weak use
Reviews paperwork only.
Row 6
- Evidence
Incident learning
- Strong use
Identifies competence, instruction and supervision factors.
- Weak use
Blames the worker without system analysis.
Read the complete comparison table
| Row | Evidence | Strong use | Weak use |
|---|---|---|---|
| 1 | Training matrix | Shows role-based requirements, status and expiry. | Lists courses without role or risk link. |
| 2 | Assessment record | Shows practical performance against criteria. | Only records attendance. |
| 3 | Supervisor check | Shows observation, coaching and correction. | Tick-box with no comments or action. |
| 4 | Training evaluation | Checks whether learning changed performance. | Asks only whether people enjoyed the course. |
| 5 | Audit | Samples documents, interviews and work as done. | Reviews paperwork only. |
| 6 | Incident learning | Identifies competence, instruction and supervision factors. | Blames the worker without system analysis. |
Training and competent-help routes
Table ID: competence-training-information-and-supervision-jurisdiction
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Column-1
Great Britain
- Column-2
HSE PUWER and competence guidance.
- Column-3
Task instruction, observed assessment and active supervision.
Row 2
- Column-1
Northern Ireland
- Column-2
HSENI competent person and responsibility guidance.
- Column-3
NI role standard, local training and supervision records.
Read the complete comparison table
| Row | Column-1 | Column-2 | Column-3 |
|---|---|---|---|
| 1 | Great Britain | HSE PUWER and competence guidance. | Task instruction, observed assessment and active supervision. |
| 2 | Northern Ireland | HSENI competent person and responsibility guidance. | NI role standard, local training and supervision records. |
BuildOut Ltd worked example
Table ID: competence-training-information-and-supervision-buildout-ltd-worked-example
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Management area
Assess and analyse
- How buildout applies it
Links tasks to hazards, legal duties, role requirements and safety-critical decisions.
- Evidence and improvement
Role risk profile, training needs analysis and competence matrix.
Row 2
- Management area
Train and instruct
- How buildout applies it
Uses induction, toolbox talks, practical demonstrations, equipment-specific training and external specialist courses where needed.
- Evidence and improvement
Training records, briefing records and practical assessment forms.
Row 3
- Management area
Supervise
- How buildout applies it
Sets closer supervision for new workers, high-risk work, contractors, apprentices and changed tasks.
- Evidence and improvement
Supervision plan, site diary, observation checks and corrective actions.
Row 4
- Management area
Control contractors
- How buildout applies it
Checks competence before appointment and monitors work against the agreed method.
- Evidence and improvement
Approved contractor list, RAMS review, permit checks and post-job review.
Row 5
- Management area
Audit and learn
- How buildout applies it
Samples records, interviews workers and observes site work to confirm competence is real.
- Evidence and improvement
Audit report, findings, ranked actions and close-out evidence.
Row 6
- Management area
Improve
- How buildout applies it
Updates training, supervision and procedures after incidents, changes and recurring findings.
- Evidence and improvement
Management review, revised matrix and refresher plan.
Read the complete comparison table
| Row | Management area | How buildout applies it | Evidence and improvement |
|---|---|---|---|
| 1 | Assess and analyse | Links tasks to hazards, legal duties, role requirements and safety-critical decisions. | Role risk profile, training needs analysis and competence matrix. |
| 2 | Train and instruct | Uses induction, toolbox talks, practical demonstrations, equipment-specific training and external specialist courses where needed. | Training records, briefing records and practical assessment forms. |
| 3 | Supervise | Sets closer supervision for new workers, high-risk work, contractors, apprentices and changed tasks. | Supervision plan, site diary, observation checks and corrective actions. |
| 4 | Control contractors | Checks competence before appointment and monitors work against the agreed method. | Approved contractor list, RAMS review, permit checks and post-job review. |
| 5 | Audit and learn | Samples records, interviews workers and observes site work to confirm competence is real. | Audit report, findings, ranked actions and close-out evidence. |
| 6 | Improve | Updates training, supervision and procedures after incidents, changes and recurring findings. | Management review, revised matrix and refresher plan. |
Role-level learning and competence evidence
Table ID: competence-training-information-and-supervision-competence-decisions
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Column-1
Plant operator
- Column-2
Demonstrate pre-use and abnormal stop to competent assessor.
- Column-3
Signed authorisation; reassess on equipment change or failure.
Row 2
- Column-1
Supervisor
- Column-2
Observe a novice, check controls and intervene on drift; operations manager assesses.
- Column-3
Observation log; reassess after missed control or role change.
Row 3
- Column-1
Trainer/assessor
- Column-2
Set task standard and observe performance; technical lead checks method.
- Column-3
Assessment record; review after procedure change.
Row 4
- Column-1
Contractor manager
- Column-2
Check task capability and site interfaces; site lead assesses.
- Column-3
Selection and induction record; refresh on scope change.
Read the complete comparison table
| Row | Column-1 | Column-2 | Column-3 |
|---|---|---|---|
| 1 | Plant operator | Demonstrate pre-use and abnormal stop to competent assessor. | Signed authorisation; reassess on equipment change or failure. |
| 2 | Supervisor | Observe a novice, check controls and intervene on drift; operations manager assesses. | Observation log; reassess after missed control or role change. |
| 3 | Trainer/assessor | Set task standard and observe performance; technical lead checks method. | Assessment record; review after procedure change. |
| 4 | Contractor manager | Check task capability and site interfaces; site lead assesses. | Selection and induction record; refresh on scope change. |
advanced safety study study prompts
Table ID: competence-training-information-and-supervision-dn1-3-1-study-prompts
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Requirement
Meaning of competence
- What to explain
Knowledge, skill, experience, behaviour and application in context.
- How to apply it
Compare a certificate with demonstrated task performance.
Row 2
- Requirement
Training needs analysis
- What to explain
How role, risk and current capability drive training priorities.
- How to apply it
Build a role-based training matrix from risk assessment.
Row 3
- Requirement
Information and instruction
- What to explain
How people receive usable task and risk information.
- How to apply it
Improve a confusing procedure or induction.
Row 4
- Requirement
Supervision
- What to explain
How oversight supports workers and verifies control use.
- How to apply it
Set supervision levels for new, young, lone or contractor workers.
Row 5
- Requirement
Competence assurance
- What to explain
How competence is assessed, recorded, reviewed and refreshed.
- How to apply it
Use observation, questioning, audit and incident learning.
Row 6
- Requirement
Organisational competence
- What to explain
How the business retains capability and gets specialist help.
- How to apply it
Identify gaps in leadership, technical authority or contractor oversight.
Read the complete comparison table
| Row | Requirement | What to explain | How to apply it |
|---|---|---|---|
| 1 | Meaning of competence | Knowledge, skill, experience, behaviour and application in context. | Compare a certificate with demonstrated task performance. |
| 2 | Training needs analysis | How role, risk and current capability drive training priorities. | Build a role-based training matrix from risk assessment. |
| 3 | Information and instruction | How people receive usable task and risk information. | Improve a confusing procedure or induction. |
| 4 | Supervision | How oversight supports workers and verifies control use. | Set supervision levels for new, young, lone or contractor workers. |
| 5 | Competence assurance | How competence is assessed, recorded, reviewed and refreshed. | Use observation, questioning, audit and incident learning. |
| 6 | Organisational competence | How the business retains capability and gets specialist help. | Identify gaps in leadership, technical authority or contractor oversight. |
Warning signs and likely causes
Table ID: competence-training-information-and-supervision-warning-signs-and-likely-causes
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Warning sign
Attendance used as proof
- How harm can develop
People may not be able to perform the task safely.
- What to improve
Add practical assessment and supervision.
Row 2
- Warning sign
Generic induction
- How harm can develop
Workers miss site-specific hazards and controls.
- What to improve
Use role and task-specific information.
Row 3
- Warning sign
Expired or missing refreshers
- How harm can develop
Rare or changed tasks are performed from memory.
- What to improve
Create risk-based refresher triggers.
Row 4
- Warning sign
No supervision plan
- How harm can develop
New, vulnerable or contractor workers are left unsupported.
- What to improve
Set supervision levels from risk assessment.
Row 5
- Warning sign
Repeated similar errors
- How harm can develop
Training may not match work as done.
- What to improve
Review work design, instruction and competence.
Row 6
- Warning sign
Specialist advice not understood
- How harm can develop
Managers may accept recommendations without proper action.
- What to improve
Retain intelligent customer capability and define actions.
Read the complete comparison table
| Row | Warning sign | How harm can develop | What to improve |
|---|---|---|---|
| 1 | Attendance used as proof | People may not be able to perform the task safely. | Add practical assessment and supervision. |
| 2 | Generic induction | Workers miss site-specific hazards and controls. | Use role and task-specific information. |
| 3 | Expired or missing refreshers | Rare or changed tasks are performed from memory. | Create risk-based refresher triggers. |
| 4 | No supervision plan | New, vulnerable or contractor workers are left unsupported. | Set supervision levels from risk assessment. |
| 5 | Repeated similar errors | Training may not match work as done. | Review work design, instruction and competence. |
| 6 | Specialist advice not understood | Managers may accept recommendations without proper action. | Retain intelligent customer capability and define actions. |
Official sources and decisions
Table ID: competence-training-information-and-supervision-official-links
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Column-1
HSE, Great Britain
- Column-2
HSE training and competence
- Column-3
Great Britain regulator guidance
- Column-4
Task-based assessment, infrequent work and contractors
Row 2
- Column-1
HSE, Great Britain
- Column-2
HSE supervision
- Column-3
Great Britain regulator guidance
- Column-4
Active supervision and checks at work
Row 3
- Column-1
HSE, Great Britain
- Column-2
HSE work-equipment training and competence
- Column-3
Great Britain PUWER guidance
- Column-4
Equipment-specific instruction and training
Row 4
- Column-1
HSE, Great Britain
- Column-2
HSE health and safety training INDG345
- Column-3
Great Britain regulator guidance
- Column-4
Training needs, methods and evaluation
Row 5
- Column-1
HSE, Great Britain
- Column-2
HSE skills, knowledge and experience under CDM
- Column-3
Great Britain construction guidance
- Column-4
Construction contractor capability and supervision
Row 6
- Column-1
HSENI, Northern Ireland
- Column-2
HSENI appointing a competent person
- Column-3
Northern Ireland regulator guidance
- Column-4
NI Management Regulations 2000 competent assistance
Row 7
- Column-1
HSENI, Northern Ireland
- Column-2
HSENI taking responsibility
- Column-3
Northern Ireland regulator guidance
- Column-4
NI information, instruction, training and supervision
Row 8
- Column-1
HSE
- Column-2
HSE Managing for health and safety (HSG65)
- Column-3
Great Britain
- Column-4
Free GB regulator guidance on planning, doing, checking and acting on health and safety controls.
Row 9
- Column-1
HSE
- Column-2
HSE five-level hierarchy
- Column-3
Great Britain
- Column-4
Higher controls first; ERICPD complementary mnemonic
Row 10
- Column-1
HSE
- Column-2
HSE lifting planning and organisation
- Column-3
Great Britain
- Column-4
Task, strength/stability, positioning, exclusion and supervision
Row 11
- Column-1
HSE
- Column-2
HSE lifting examinations and inspections
- Column-3
Great Britain
- Column-4
Pre-use checks, maintenance, competent examination and defect response
Read the complete comparison table
| Row | Column-1 | Column-2 | Column-3 | Column-4 |
|---|---|---|---|---|
| 1 | HSE, Great Britain | HSE training and competence | Great Britain regulator guidance | Task-based assessment, infrequent work and contractors |
| 2 | HSE, Great Britain | HSE supervision | Great Britain regulator guidance | Active supervision and checks at work |
| 3 | HSE, Great Britain | HSE work-equipment training and competence | Great Britain PUWER guidance | Equipment-specific instruction and training |
| 4 | HSE, Great Britain | HSE health and safety training INDG345 | Great Britain regulator guidance | Training needs, methods and evaluation |
| 5 | HSE, Great Britain | HSE skills, knowledge and experience under CDM | Great Britain construction guidance | Construction contractor capability and supervision |
| 6 | HSENI, Northern Ireland | HSENI appointing a competent person | Northern Ireland regulator guidance | NI Management Regulations 2000 competent assistance |
| 7 | HSENI, Northern Ireland | HSENI taking responsibility | Northern Ireland regulator guidance | NI information, instruction, training and supervision |
| 8 | HSE | HSE Managing for health and safety (HSG65) | Great Britain | Free GB regulator guidance on planning, doing, checking and acting on health and safety controls. |
| 9 | HSE | HSE five-level hierarchy | Great Britain | Higher controls first; ERICPD complementary mnemonic |
| 10 | HSE | HSE lifting planning and organisation | Great Britain | Task, strength/stability, positioning, exclusion and supervision |
| 11 | HSE | HSE lifting examinations and inspections | Great Britain | Pre-use checks, maintenance, competent examination and defect response |
Source tables and records 2
Acronyms and plain-English meanings
Table ID: competence-training-information-and-supervision-acronyms-and-plain-english-meanings
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Acronym
CDM
- Meaning
Construction (Design and Management) Regulations
- Why it matters
Construction duties include skills, knowledge, experience and organisational capability.
Row 2
- Acronym
COSHH
- Meaning
Control of Substances Hazardous to Health
- Why it matters
Hazardous substance controls often require specific instruction, training and supervision.
Row 3
- Acronym
DN1
- Meaning
IOSH Diploma Unit DN1
- Why it matters
The unit covering workplace health and safety principles and management.
Row 4
- Acronym
HSE
- Meaning
Health and Safety Executive
- Why it matters
Great Britain regulator; Northern Ireland uses HSENI.
Row 5
- Acronym
ISO
- Meaning
International Organization for Standardization
- Why it matters
Produces standards such as ISO 45001 for management systems.
Row 6
- Acronym
PDCA
- Meaning
Plan, Do, Check, Act
- Why it matters
HSG65-style management cycle.
Row 7
- Acronym
PUWER
- Meaning
Provision and Use of Work Equipment Regulations
- Why it matters
Requires adequate work-equipment training for use, supervision and management.
Row 8
- Acronym
RAMS
- Meaning
Risk assessment and method statement
- Why it matters
Common contractor planning documents that need competent review.
Row 9
- Acronym
TNA
- Meaning
Training needs analysis
- Why it matters
Structured method for identifying what training and competence development is needed.
Read the complete comparison table
| Row | Acronym | Meaning | Why it matters |
|---|---|---|---|
| 1 | CDM | Construction (Design and Management) Regulations | Construction duties include skills, knowledge, experience and organisational capability. |
| 2 | COSHH | Control of Substances Hazardous to Health | Hazardous substance controls often require specific instruction, training and supervision. |
| 3 | DN1 | IOSH Diploma Unit DN1 | The unit covering workplace health and safety principles and management. |
| 4 | HSE | Health and Safety Executive | Great Britain regulator; Northern Ireland uses HSENI. |
| 5 | ISO | International Organization for Standardization | Produces standards such as ISO 45001 for management systems. |
| 6 | PDCA | Plan, Do, Check, Act | HSG65-style management cycle. |
| 7 | PUWER | Provision and Use of Work Equipment Regulations | Requires adequate work-equipment training for use, supervision and management. |
| 8 | RAMS | Risk assessment and method statement | Common contractor planning documents that need competent review. |
| 9 | TNA | Training needs analysis | Structured method for identifying what training and competence development is needed. |
Individual editable BuildOut documents
Table ID: competence-training-information-and-supervision-buildout-documents
Source: https://www.sharehub.ltd/knowledge-hub/competence-training-information-and-supervision.html
Row 1
- Document
Competence verification and induction procedureBOUK-PRO-COMP · Completed fictional example · v1.0
- Purpose
Check role-specific evidence and practical capability; identify training needs and supervision.
- Editable download
Download DOCXRead preview
Row 2
- Document
Role competence and training matrixBOUK-REG-COMP-01 · Blank register with separate fictional worked entries · v1.0
- Purpose
Match actual work and expiry dates to verified competence and supervision needs.
- Editable download
Download XLSXRead preview
Row 3
- Document
Worker competence verification and authorisationBOUK-CHK-COMP-01 · Blank editable master · v1.0
- Purpose
Check evidence and practical capability before allocating higher-risk tasks.
- Editable download
Download DOCXRead preview
Row 4
- Document
Project and visitor induction checklistBOUK-CHK-COMP-02 · Blank editable master · v1.0
- Purpose
Explain site rules, hazards, welfare, emergency routes and reporting.
- Editable download
Download DOCXRead preview
Row 5
- Document
Training, familiarisation and supervision recordBOUK-FRM-COMP-01 · Blank editable master · v1.0
- Purpose
Record learning, assessment, limitations and supervisor follow-up.
- Editable download
Download DOCXRead preview
Row 6
- Document
Training-needs and refresher programmeBOUK-PLN-COMP-01 · Completed fictional example · v1.0
- Purpose
Prioritise competence gaps and mandatory/specialist training by actual activities.
- Editable download
Download DOCXRead preview
Row 7
- Document
Apprentice and inexperienced-worker supervision planBOUK-FRM-COMP-02 · Blank editable master · v1.0
- Purpose
Specify restricted tasks, competent supervision and progressive authorisation.
- Editable download
Download DOCXRead preview
Read the complete comparison table
| Row | Document | Purpose | Editable download |
|---|---|---|---|
| 1 | Competence verification and induction procedureBOUK-PRO-COMP · Completed fictional example · v1.0 | Check role-specific evidence and practical capability; identify training needs and supervision. | Download DOCXRead preview |
| 2 | Role competence and training matrixBOUK-REG-COMP-01 · Blank register with separate fictional worked entries · v1.0 | Match actual work and expiry dates to verified competence and supervision needs. | Download XLSXRead preview |
| 3 | Worker competence verification and authorisationBOUK-CHK-COMP-01 · Blank editable master · v1.0 | Check evidence and practical capability before allocating higher-risk tasks. | Download DOCXRead preview |
| 4 | Project and visitor induction checklistBOUK-CHK-COMP-02 · Blank editable master · v1.0 | Explain site rules, hazards, welfare, emergency routes and reporting. | Download DOCXRead preview |
| 5 | Training, familiarisation and supervision recordBOUK-FRM-COMP-01 · Blank editable master · v1.0 | Record learning, assessment, limitations and supervisor follow-up. | Download DOCXRead preview |
| 6 | Training-needs and refresher programmeBOUK-PLN-COMP-01 · Completed fictional example · v1.0 | Prioritise competence gaps and mandatory/specialist training by actual activities. | Download DOCXRead preview |
| 7 | Apprentice and inexperienced-worker supervision planBOUK-FRM-COMP-02 · Blank editable master · v1.0 | Specify restricted tasks, competent supervision and progressive authorisation. | Download DOCXRead preview |