SHARE Knowledge Hub
Nitroglycerine effects at work
Occupational nitroglycerine (glyceryl trinitrate) exposure requires control of airborne and skin routes during manufacture, handling and maintenance. Identify the actual nitrate ester and mixture, contain exposure at source, and stop the suspected task if a worker reports illness. If a worker becomes unwell during or after the task, stop suspected exposure, keep the formulation and exposure details, and arrange appropriate clinical assessment. A clinician determines the cause and fitness for work.
Understanding Nitroglycerine effects at work
Occupational nitroglycerine (glyceryl trinitrate) exposure requires control of airborne and skin routes during manufacture, handling and maintenance. Identify the actual nitrate ester and mixture, contain exposure at source, and stop the suspected task if a worker reports illness. If a worker becomes unwell during or after the task, stop suspected exposure, keep the formulation and exposure details, and arrange appropriate clinical assessment. A clinician determines the cause and fitness for work.
Why this matters at work
GTN can enter by inhalation, skin absorption and ingestion, and wet material or clothing can sustain contact. Temperature, agitation, pressure and task position influence how a formulation reaches the breathing zone and skin. A sample away from the opening can miss the worker’s short exposure. Map normal transfer, sampling, residues and maintenance, not only the main process. The Sk notation signals that all-route control matters and explains why a clean air report cannot be treated as total-dose assurance.
Energetic-material work can constrain protective materials, cleaning and waste methods as well as chemical resistance. A formulation-specific glove assessment must therefore sit within the specialist process-safety system. Wet cuffs and contaminated clothing can become reservoirs for skin uptake. Safe removal and changing prevent a barrier from transferring exposure after the task. Retain supplier evidence and limits and use only a method accepted for the actual material; generic handling advice cannot settle explosive compatibility or authorise work.
How organisations manage this in practice
Obtain product-specific compatibility advice for the formulation and task, including energetic-material constraints where relevant. Define inspection, change, removal and waste arrangements that avoid secondary contact. Observe cuffs and any wet clothing. Record the product, conditions and limitations so a purchasing substitution triggers review. Chemical resistance is only one part of suitability, and a glove cannot justify an avoidable leak or unsafe cleaning method.
Assess inhalation, direct liquid contact and contaminated clothing as a combined uptake problem. Observe coupling work, sampling and cleanup, and check where hands and sleeves contact residues. Match the monitoring strategy to those routes and keep the process conditions with results. Control release at source before relying on PPE. A general room reading cannot establish personal inhaled dose or exclude skin absorption.
Use the glycerol trinitrate entry and CAS identity, then check the live table and the jurisdiction’s approval route. Keep daily and short-term comparisons separate and account for skin uptake. Do not substitute the limit for a related nitrate ester or an old report. A numerical result below a WEL does not resolve symptoms, poor containment, explosive-material safety or the suitability of a worker for a specific task.
Check the sample, the short task and the skin route
An air sample describes particular sampling conditions. It cannot, on its own, resolve a short exposure peak or contact with a contaminated fitting during cleaning.

Sampling period
Record what the sample represents: task, period, method and operating conditions. Keep limitations visible beside the result.
Task peak
Identify short tasks and abnormal events that the sampling period may not represent; obtain competent exposure assessment.
Contaminated surface
Trace contact at fittings, tools, gloves and clothing during cleaning and maintenance. A low air result does not clear these routes.
Skin prevention
Assess containment and contact prevention for the actual material and method, including the clean/dirty clothing boundary.
Formulation matters
Establish the actual formulation and process. This conceptual scene gives no permission to handle an energetic material or alter a cleaning method.
Clinical advice separate
Symptoms, diagnosis and return-to-work advice use the confidential competent health route. Do not test “tolerance” by sending someone back into exposure.
Keep uncertain exposure or a defective control on hold for competent assessment. The drawing supplies no exposure number, diagnosis or handling instruction.
How should possible health effects be handled?
Treat illness reported after a nitrate-ester task as a reason to stop suspected exposure, review controls and obtain competent clinical advice; symptoms alone do not establish cause.
HSE's EH40 glycerol-trinitrate entry carries a skin notation and workplace exposure limits, so an air result alone cannot establish that exposure is controlled. Illness reported during or after this work needs clinical assessment; symptoms alone cannot identify the substance or cause. Do not diagnose tolerance, withdrawal or causation on site. Record the actual formulation, task, timing, possible skin contact and air-control evidence for the clinician and exposure specialist. The clinician interprets the person's condition while the process owner checks the suspected exposure route and controls. Source: HSE EH40 glycerol-trinitrate entry.
Possible effects include headache, dizziness, nausea and cardiovascular effects such as low blood pressure or palpitations. Report these and obtain assessment; they do not prove the substance or cause. NIOSH nitroglycerine health information is used for health information only, while UK values and task-specific RPE selection remain governed by the applicable UK sources. Do not infer a universal Monday-headache or withdrawal timetable from mixed-exposure material.
How should exposure be assessed?
Identify each nitrate ester, skin and air routes, frequency, co-exposures, symptoms and the role of each control before comparing any limit.
Nitroglycerine can be absorbed through skin, so assess contaminated surfaces, gloves and clothing as well as air. A competent specialist should decide whether biological monitoring is appropriate for the actual product and exposure. HSE COSHH control guidance.
EH40 fourth edition lists glycerol trinitrate at 0.01 parts per million (ppm), or 0.095 mg/m³, averaged over eight hours, and 0.02 ppm, or 0.19 mg/m³, over 15 minutes, with a skin-absorption notation. These are not safe targets; the named formulation, skin contact and control performance govern the work. HSENI approves EH40 for NI. Check the HSE EH40 glycerol-trinitrate entry and HSENI approval. Any biomonitoring result requires specialist interpretation.
EH40 Table 2 lists a biological monitoring guidance value for glycerol trinitrate of 15 μmol total nitroglycols/mol creatinine in urine, sampled at the end of the exposure period. This non-statutory guidance value can complement air sampling through specialist-led monitoring with informed voluntary participation. It is not a diagnostic threshold or a replacement for the airborne WEL. An exceedance prompts investigation of controls, not an automatic diagnosis; a result below the value does not end the duty to improve control. Leave sampling strategy and mixture interpretation to competent specialists. See EH40 Table 2 and paragraphs 80–83.
How can the hierarchy of controls reduce nitroglycerine exposure and harmful health effects?
Use enclosed or automated handling and suitable extraction, then tested skin protection and hygiene for residual contact.
Which controls should prevent exposure? — part 1 of 2
Read the complete visual as text
- Use enclosed or automated handling and suitable extraction, then…: Use enclosed or automated handling and suitable extraction, then tested skin protection and hygiene for residual contact.
- Reduce manual contact, contain transfers, maintain extraction and keep…: Reduce manual contact, contain transfers, maintain extraction and keep contaminated surfaces and tools from spreading material. Select compatible gloves and clothing for the actual formulation and change them safely. Provide washing and laundering arrangements that do not send contamination home. Respiratory protection and routine medical monitoring cannot compensate for an open release. Stop for a leak, failed extraction, wet clothing or symptoms and secure the process under site arrangements. Sources: HSE COSHH control measures , HSENI COSHH guidance .
- HSE places elimination and substitution before engineering controls, administrative…: HSE places elimination and substitution before engineering controls, administrative measures and PPE. Apply that order to the task, then check whether the selected controls work in use.
Which controls should prevent exposure? — part 2 of 2
Read the complete visual as text
- At the filling line, the process owner first considers…: At the filling line, the process owner first considers whether the nitrate-ester task can be designed out or an approved less hazardous formulation can meet the need; a worker must never change an energetic formulation independently. Where the material remains necessary, enclosure and automated transfer interrupt skin and air routes before gloves or procedures are considered. The engineer checks containment and extraction in normal and cleaning modes, and the manager releases work only after leak checks and a competent assessment; a failed seal or symptom holds the line. HSE COSHH control measures .
- Keep physical controls effective through inspection, maintenance and action…: Keep physical controls effective through inspection, maintenance and action when a check fails. A reminder or retraining alone cannot compensate for a leaking transfer, failed extraction or dangerous atmosphere.
Reduce manual contact, contain transfers, maintain extraction and keep contaminated surfaces and tools from spreading material. Select compatible gloves and clothing for the actual formulation and change them safely. Provide washing and laundering arrangements that do not send contamination home. Respiratory protection and routine medical monitoring cannot compensate for an open release. Stop for a leak, failed extraction, wet clothing or symptoms and secure the process under site arrangements. Sources: HSE COSHH control measures, HSENI COSHH guidance.
HSE places elimination and substitution before engineering controls, administrative measures and PPE. Apply that order to the task, then check whether the selected controls work in use.
At the filling line, the process owner first considers whether the nitrate-ester task can be designed out or an approved less hazardous formulation can meet the need; a worker must never change an energetic formulation independently. Where the material remains necessary, enclosure and automated transfer interrupt skin and air routes before gloves or procedures are considered. The engineer checks containment and extraction in normal and cleaning modes, and the manager releases work only after leak checks and a competent assessment; a failed seal or symptom holds the line. HSE COSHH control measures.
Keep physical controls effective through inspection, maintenance and action when a check fails. A reminder or retraining alone cannot compensate for a leaking transfer, failed extraction or dangerous atmosphere.
When is medical escalation urgent?
Stop suspected exposure and arrange clinical help. For suspected poisoning or collapse, severe breathing difficulty or seizure, call 999 and activate the local emergency arrangement; a clinician assesses the condition and fitness for work.
Give the clinician the product identity, exposure schedule, reported symptoms, dates and possible EGDN co-exposure. Management should review containment, extraction, skin contact and affected work without storing confidential clinical detail in the open risk register. This page does not set a diagnosis or return-to-work test. Source: HSE COSHH control measures.
What GB and NI duties apply?
The employer must assess and control the substance under the applicable GB or NI COSHH regime and use the current EH40 entry for the identified material.
GB COSHH 2002 and NI COSHH 2003 are distinct instruments. HSENI approves EH40 for NI. A limit value is not a target and cannot show skin uptake is controlled. Explosives manufacture also has separate process-safety duties; this health page does not provide instructions for energetic material. A diagnosis, incident and reporting decision need the relevant regulator criteria, not a symptom label alone. Sources: HSE COSHH control measures, HSENI COSHH guidance.
How should managers test control effectiveness?
Check enclosure, extraction, contact prevention and worker symptom reports, then verify corrective action in the actual task.
A pre-use check should cover formulation, closed handling, airflow indication, glove integrity and clean changing area. During work, a leak or wet clothing prompts a hold and exposure response. Review exposure measurements or biomonitoring through competent specialists if used; explain results to workers and act on adverse trends. Reassess after a changed mixture, a different shift pattern, or reported illness after suspected exposure.
What should each role demonstrate?
Operators need safe handling and symptom reporting; supervisors need a hold decision; specialists must assess exposure and fitness within their scope.
Train workers to identify the formulation, contact points, protective clothing method and urgent symptoms. Maintainers need controlled isolation and cleaning. Supervisors should demonstrate stopping an uncontrolled line and escalating reported illness after suspected exposure. A hygienist assesses exposure; a clinician evaluates health and work fitness. Check understanding through observed tasks and revisit it after process change, symptoms or a failed control.
| Role | Learning to test | Competence evidence | Assessor and record | Reassess when |
|---|---|---|---|---|
| Nearby worker | Recognise release and emergency route | Alerts and avoids contaminated area | Supervisor; briefing check | Process or access change |
| Filling operator | Formulation, enclosed work and safe clothing | Observed pre-use check, stop and change method | Supervisor; task authorisation | New mixture or symptom |
| Maintainer | Isolation and residue control | Observed safe service and hand-back | Engineering lead; work record | Line or cleaning change |
| Supervisor / manager | Hold, referral and restart decisions | Recorded control review and authorised release | Operations lead; action review | Reported illness after suspected exposure or failed control |
| Hygienist / clinician | Exposure and health judgement within scope | Sampling report or confidential fitness advice | Specialist lead; scoped record | Exposure trend or reported illness |
Practise recognising headache, dizziness, nausea or palpitations as concerns requiring assessment, without diagnosing the cause. Rehearse the 999/local emergency response for suspected poisoning or collapse, severe breathing difficulty or seizure, and the formulation/timing/skin-contact handover. A normal air result or improved symptoms cannot be used as a return-to-work test.
What should be recorded?
Identify the formulation, skin and air routes, enclosed process, protective method, health-response route, owner and restart evidence.
Link the process risk assessment to supplier information, extraction tests, glove selection, maintenance, exposure evidence and occupational-health programme without storing confidential diagnoses in the open register. A repeated complaint or altered work pattern should trigger review, not a blanket assumption that workers have become tolerant.
How can an employer keep controls effective?
HSE explains that a formal health and safety management system is optional. The employer must still plan, control, check and improve the measures for this task. The task still needs a current COSHH assessment and verified exposure controls.
It can help allocate control ownership, consultation and corrective action. The actual substance, COSHH assessment, exposure evidence and competent clinical advice determine the task response. Certification is not evidence that a specific filling line is controlled. HSE management-system guidance explains how to plan, check and improve practical controls.
What does a low air result leave unanswered?
It can leave skin contact, short tasks, maintenance exposure and formulation-specific hazards unanswered.
What does a low air result leave unanswered? — part 1 of 2
Read the complete visual as text
- It can leave skin contact, short tasks, maintenance exposure…: It can leave skin contact, short tasks, maintenance exposure and formulation-specific hazards unanswered.
- In an illustrative filling-line review, the hygienist reports an…: In an illustrative filling-line review, the hygienist reports an air result below the relevant time-weighted benchmark. The maintainer then shows residue on a connection that is opened during cleaning. These facts are compatible: the air sample may describe one exposure route during a particular operating period, while the cleaning task creates skin contact outside that sample's scope. See HSE EH40 workplace exposure limits .
- Read the report with its substance identity, units, averaging…: Read the report with its substance identity, units, averaging period, sampled tasks and operating conditions. EH40's skin notation is a reason to examine dermal exposure, not a conversion factor for adding skin absorption to an air measurement. Do not invent a safe amount of skin contamination from a result expressed in milligrams per cubic metre. See HSE COSHH control measures .
What does a low air result leave unanswered? — part 2 of 2
Read the complete visual as text
- The manager asks the process specialist and hygienist to…: The manager asks the process specialist and hygienist to review the transfer connection, cleaning method and clothing-change arrangements. Selection of gloves must suit the actual formulation and work; a generic chemical glove label is insufficient evidence. Report illness through the clinical route without asking workers to prove the cause themselves. The worked decision concerns control evidence, not a diagnosis or a nitrate-ester treatment protocol. See HSE COSHH control measures .
- Decision basis: HSE EH40 workplace exposure limits . HSE…: Decision basis: HSE EH40 workplace exposure limits . HSE COSHH control measures . The scenario and suggested records are illustrative; apply the source within its stated jurisdiction and the assessed work.
In an illustrative filling-line review, the hygienist reports an air result below the relevant time-weighted benchmark. The maintainer then shows residue on a connection that is opened during cleaning. These facts are compatible: the air sample may describe one exposure route during a particular operating period, while the cleaning task creates skin contact outside that sample's scope. See HSE EH40 workplace exposure limits.
Read the report with its substance identity, units, averaging period, sampled tasks and operating conditions. EH40's skin notation is a reason to examine dermal exposure, not a conversion factor for adding skin absorption to an air measurement. Do not invent a safe amount of skin contamination from a result expressed in milligrams per cubic metre. See HSE COSHH control measures.
The manager asks the process specialist and hygienist to review the transfer connection, cleaning method and clothing-change arrangements. Selection of gloves must suit the actual formulation and work; a generic chemical glove label is insufficient evidence. Report illness through the clinical route without asking workers to prove the cause themselves. The worked decision concerns control evidence, not a diagnosis or a nitrate-ester treatment protocol. See HSE COSHH control measures.
Decision basis: HSE EH40 workplace exposure limits. HSE COSHH control measures. The scenario and suggested records are illustrative; apply the source within its stated jurisdiction and the assessed work.
How should a serviced fitting be accepted for use?
Accept the defined repair and exposure barriers together; an idle or externally clean line is not proof that internal residue is controlled.
Before opening equipment, the maintainer needs a verified product identity and a controlled work method for isolation, residue and any process hazards. Where formulation or safe cleaning conditions are unknown, hold the job for the responsible specialist. This health lesson does not provide manufacturing, energetic-material handling or decontamination instructions. See HSE COSHH control measures.
After the repair, inspect the relevant enclosure, transfer seals and extraction under the agreed conditions, and document the specialist's acceptance evidence. Make the work boundary clear: release of one repaired fitting does not authorise an altered formulation or a different cleaning task. Keep individual clinical notes confidential and communicate only the necessary work advice through the agreed occupational-health route. See HSENI COSHH guidance.
Decision basis: HSE COSHH control measures. HSENI COSHH guidance. The scenario and suggested records are illustrative; apply the source within its stated jurisdiction and the assessed work.
Which assumptions should a learner challenge?
Challenge assumptions about mixture identity, skin protection and medical fitness before accepting a familiar work routine.
Learning check: a delivery label looks similar to last month's material, but its formulation has changed. The correct response is to verify the actual substance and assessment with the process owner, not to transfer the previous exposure or glove decision automatically. A trade name and an old air result do not establish equivalent hazards. See HSE COSHH control measures.
Learning check: a worker feels better after leaving the task and wants to return. The supervisor must arrange appropriate clinical advice and hold the suspect exposure route until controls have been assessed. Settled symptoms do not establish either medical fitness or successful control repair. See HSE EH40 workplace exposure limits.
Ask the operator to demonstrate the pre-use barrier check and explain the reporting route, and ask the supervisor to identify the evidence needed for restart. Record the scope of that assessment and changed conditions that require reassessment. Do not award competence for memorising a symptom list that has not been established for the actual formulation. See HSE EH40 workplace exposure limits.
Decision basis: HSE COSHH control measures. HSE EH40 workplace exposure limits. The scenario and suggested records are illustrative; apply the source within its stated jurisdiction and the assessed work.
Which terms matter?
These names prevent a mixture and a health effect being treated as one thing.
| Term | Expansion or meaning | Use here |
|---|---|---|
| GTN | Glyceryl trinitrate | Another name for nitroglycerine. |
| EGDN | Ethylene glycol dinitrate | Possible co-ingredient in nitrate-ester mixtures. |
| COSHH | Control of Substances Hazardous to Health | Separate GB and NI instruments. |
| WEL | Workplace exposure limit | Substance-specific air benchmark. |
| LEV | Local exhaust ventilation | Source control for an assessed process. |
| HSE | Health and Safety Executive | Great Britain workplace regulator; use its guidance within scope. |
| HSENI | Health and Safety Executive for Northern Ireland | Northern Ireland workplace regulator; NI duties have separate instruments. |
| GB | Great Britain | England, Scotland and Wales; distinguish the NI legal route. |
| NI | Northern Ireland | Use the Northern Ireland legislation and regulator route. |
| EH40 | HSE workplace exposure limits publication | Read the actual substance, units, averaging period and notations. |
| PPE | Personal protective equipment | Residual personal protection supporting stronger source controls. |
| ERICPD | Eliminate; Reduce; Isolate; Control; PPE; Discipline | SHARE planning prompt; Discipline means maintaining controls, not blame. |
| ISO | International Organization for Standardization | Voluntary standards context; certification does not authorise a task. |