Full public teaching and readers are free without an account. A free learner account is required for saved LMS progress and recorded assessment. Completion and any course-completion certificate depend on the configured LMS conditions. Open the course overview.
Lesson 1
Define the job and its energy sources
Identify hazardous energy and interfaces before maintenance begins.
Define the job and its energy sources
Maintenance may expose hazards hidden during normal operation. Define the equipment boundary and the electrical, mechanical, pressure, thermal and other energy that can affect the task. Isolation requires competent planning, control of stored energy and verification.
Coordinate isolation, contractors and specialist tools.
Follow the task through the area
Sparks beside stored packaging
A contractor proposes cutting a bracket near packaging stock and hidden voids.
A damaged lead on a cleaning machine
The machine has a damaged lead and is being taken towards a damp floor.
A noisy task beside another workstation
A noisy tool is being used next to a staffed desk without an exposure assessment.
Unplanned extra time on a vibrating tool
A worker has taken on additional tool work and the actual daily use has not been reviewed.
Maintenance conflicts with warehouse traffic
A contractor has set up a repair across a route that remains in use.
An unverified grinding wheel is fitted
A replacement wheel has unclear markings and has not been checked against the machine or material.
An oxygen connection is treated like ordinary air
A contractor proposes fitting a spare regulator to an oxygen cylinder because the connector appears to fit. The part has been stored beside oily tools and its oxygen-service suitability is unknown.
Challenge the first impression
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
What is control of ignition sources and hot work?
It is the prevention and management of work or conditions that could ignite combustible or explosive materials.
The control starts by identifying fuels: ordinary combustibles, flammable liquids, vapours, gases, mists, combustible dusts, residues, packaging, insulation, timber, roof materials, cable trays, oils, greases and waste. Then identify ignition sources that could meet those fuels during normal work, maintenance, cleaning, shutdown, construction or emergency repairs.
Hot work is a special case because it deliberately introduces heat, flame or sparks. A robust system asks whether hot work can be eliminated, whether the item can be moved to a safe area, whether fuels and residues can be removed, whether isolation and gas testing are adequate, whether the permit area includes hidden spaces and whether someone will keep watch long enough after the work.
Ignition source and hot-work scope
Area
Examples
Typical controls
Open flames and hot work
Welding, cutting, brazing, soldering, torches and heat guns.
Avoidance, permit, shielding, fire watch and gas testing.
Mechanical sparks and friction
Grinding, abrasive cutting, seized bearings and metal impact.
Tool selection, maintenance, exclusion zones and housekeeping.
Electrical ignition
Damaged cables, overloaded circuits, temporary electrics and non-ATEX equipment.
Inspection, maintenance and suitable equipment.
Static electricity
Liquid transfer, powder handling and synthetic materials.
Bonding, earthing, humidity and transfer controls.
Hot surfaces
Exhausts, heaters, ovens, lamps, motors and process equipment.
Temperature control, separation and guarding.
Smoking and arson opportunity
Smoking materials, poor security and waste near buildings.
No-smoking controls, security and waste management.
Applied case
A contractor arrives to repair equipment while production continues nearby. Hot work, a damaged extension lead, a noisy tool and an oxygen set share the workshop.
Compare your decision
Maintenance may expose hazards hidden during normal operation. Define the equipment boundary and the electrical, mechanical, pressure, thermal and other energy that can affect the task. Isolation requires competent planning, control of stored energy and verification.
Maintenance may expose hazards hidden during normal operation. Define the equipment boundary and the electrical, mechanical, pressure, thermal and other energy that can affect the task. Isolation requires competent planning, control of stored energy and verification. Check the actual conditions and retain protection while gaps are resolved.
Lesson 2
Coordinate the contractor and the warehouse
Recognise hot-work, electrical, noise, vibration, wheel and gas-equipment hazards.
Coordinate the contractor and the warehouse
The contractor needs relevant site information and clear responsibilities, while the warehouse must understand how the work affects routes, nearby people and operations. A permit records agreed controls; it does not physically provide them.
Coordinate isolation, contractors and specialist tools.
Follow the task through the area
Sparks beside stored packaging
A contractor proposes cutting a bracket near packaging stock and hidden voids.
A damaged lead on a cleaning machine
The machine has a damaged lead and is being taken towards a damp floor.
A noisy task beside another workstation
A noisy tool is being used next to a staffed desk without an exposure assessment.
Unplanned extra time on a vibrating tool
A worker has taken on additional tool work and the actual daily use has not been reviewed.
Maintenance conflicts with warehouse traffic
A contractor has set up a repair across a route that remains in use.
An unverified grinding wheel is fitted
A replacement wheel has unclear markings and has not been checked against the machine or material.
An oxygen connection is treated like ordinary air
A contractor proposes fitting a spare regulator to an oxygen cylinder because the connector appears to fit. The part has been stored beside oily tools and its oxygen-service suitability is unknown.
Challenge the first impression
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
What is portable electrical equipment?
Portable electrical equipment is work equipment connected to an electrical supply by a plug and flexible cable and moved or handled during use or between uses.
Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.
Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.
Read all six steps as text
1. What is portable electrical equipment?
Portable electrical equipment is work equipment connected to an electrical supply by a plug and flexible cable and moved or handled during use or between uses.
Avoid / redesign: Eliminate: the project lead first asks whether the cutting can be completed off-site or by a pre-cut component.
Control the task: Isolate and engineer: route leads away from traffic and water, protect connectors and use supply protection selected by a competent electrical person.
Verify before release: Read the full task example, checks and stop points on this page.
Portable electrical equipment is work equipment connected to an electrical supply by a plug and flexible cable and moved or handled during use or between uses. Portable electrical equipment ranges from a static office charger to a hand-held tool or cleaning machine.
Apply it: Which part of this plan would you check at the workface before authorising the task?
2. Turn portable electrical equipment knowledge into a decision
Use the evidence to improve the actual work arrangement.
Change at source: Eliminate: the project lead first asks whether the cutting can be completed off-site or by a pre-cut component.
Make it observable: Read the full task example, checks and stop points on this page.
Keep useful evidence: Equipment specification, risk assessment, user check, defect quarantine, repair/test and return-to-use decision.
Portable electrical equipment ranges from a static office charger to a hand-held tool or cleaning machine. Damaged cables, unsuitable equipment and wet or rough use can allow shock, burns or fire; the maintenance decision depends on the equipment and the conditions of use. Equipment specification, risk assessment, user check, defect quarantine, repair/test and return-to-use decision.
Apply it: What evidence would show that the change improves this task, rather than only completing a record?
Fictional example: a practical application of the existing topic lesson.
Setting: Cleaning contractor uses a mains floor polisher at a wet entrance; supply, rating and cable route matter.
Act: Confirm suitability, route lead away from water and traffic, check plug/casing/lead and inspection history.
Hold / review: Crushed or exposed cable, wet connection or repeated trip; disconnect and quarantine.
Keep lead dry and protected, watch for damage or protective-device trips, keep others clear. Competent repair/inspection/test where needed, then supervisor releases the machine for use.
Apply it: At which point would you hold this example, and what evidence would allow it to proceed?
4. What determines inspection and testing frequency?
Connect the task, the route to the person and the control that can fail.
Source / exposure: Frequency should be based on equipment type, environment, use, movement, damage history and user competence.
Possible consequence: The most important shift for learners is this: there is no legal requirement for every portable appliance to be tested every year.
Control failure: The legal requirement is maintenance to prevent danger.
Frequency should be based on equipment type, environment, use, movement, damage history and user competence.
Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?
5. Choose controls for portable electrical equipment
Start with the stronger practicable options and verify their effect.
Eliminate: Eliminate: the project lead first asks whether the cutting can be completed off-site or by a pre-cut component.
Reduce: Substitute and reduce: if cutting remains, assess a suitable lower-voltage or battery tool for the material, runtime and environment.
Isolate: Isolate and engineer: route leads away from traffic and water, protect connectors and use supply protection selected by a competent electrical person.
Control: Control, PPE and Discipline: brief users on checks, keep a defect route and authorise repairs and testing to people with the required competence.
Eliminate: Eliminate: the project lead first asks whether the cutting can be completed off-site or by a pre-cut component. Reduce: Substitute and reduce: if cutting remains, assess a suitable lower-voltage or battery tool for the material, runtime and environment. Isolate: Isolate and engineer: route leads away from traffic and water, protect connectors and use supply protection selected by a competent electrical person. Control: Control, PPE and Discipline: brief users on checks, keep a defect route and authorise repairs and testing to people with the required competence. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.
Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?
Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.
The risk profile varies enormously. A laptop power supply in a dry office is not the same as a 230 V pressure washer used outdoors, an angle grinder on a construction site, a floor polisher used by a cleaning contractor, a catering extension lead, or a battery charger in a workshop. HSG107 is important because it moves the topic away from automatic annual testing and towards risk-based maintenance.
The main hazards are electric shock, burns, arcing, fire, trip hazards, equipment failure and secondary injury. Damage often occurs to plugs, flexible cables, strain relief, casing, switches, extension leads and equipment used in wet, dusty, hot, abrasive or outdoor environments.
Good management is a system: select suitable equipment, provide safe supply, train users, carry out user checks, complete formal visual inspections, test where justified, keep records proportionate, quarantine defects and review frequencies after damage or incidents.
Topic
What it means
Management implication
Portable equipment
Equipment moved or handled and connected by plug and cable.
Likely to suffer damage, so needs checks and maintenance.
Transportable equipment
Equipment moved between locations but not necessarily hand-held during use.
Assess travel, set-up, cable route and supply.
User check
Simple pre-use look and feel check by the user.
Find obvious damage before use.
Formal visual inspection
Recorded inspection by a competent person.
Find damage users may miss.
Combined inspection and test
Electrical tests plus inspection where risk justifies it.
Use risk-based intervals, not automatic annual PAT.
RCD
Residual current device that disconnects supply quickly after some faults.
Useful additional protection, not a substitute for safe equipment.
Inspection/test records and labels are useful management evidence, but there is no automatic standalone legal requirement to record every PAT activity or attach a sticker. Other applicable inspection duties may require records. Evidence should support the maintenance decision, not replace a present-condition check.
Applied case
A contractor arrives to repair equipment while production continues nearby. Hot work, a damaged extension lead, a noisy tool and an oxygen set share the workshop.
Compare your decision
The contractor needs relevant site information and clear responsibilities, while the warehouse must understand how the work affects routes, nearby people and operations. A permit records agreed controls; it does not physically provide them.
The contractor needs relevant site information and clear responsibilities, while the warehouse must understand how the work affects routes, nearby people and operations. A permit records agreed controls; it does not physically provide them. Check the actual conditions and retain protection while gaps are resolved.
Lesson 3
Sparks beside stored packaging
Hold the hot work and have the responsible person assess a cold method or a fully controlled task and hand-back.
Read the scene evidence
A contractor proposes cutting a bracket near packaging stock and hidden voids.
Identify the condition separately from the exposed person and any possible outcome.
How the harm pathway develops
Ignition-producing work beside combustible materials
A contractor proposes cutting a bracket near packaging stock and hidden voids.
How people can be exposed
Sparks or heat reach combustible material during or after the task.
Possible harm
A developing fire or smoke affecting work and escape routes.
A contractor proposes cutting a bracket near packaging stock and hidden voids. The condition remains unresolved.
Protective response
Hold the hot work and have the responsible person assess a cold method or a fully controlled task and hand-back.
Select controls by how they prevent harm
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.
Control level
Application to this case
Elimination
Avoid hot work by using a suitable cold cutting or off-site fabrication method.
Substitution
Compare a lower-ignition method after checking its other hazards.
Engineering controls
Provide suitable separation and physical protection for the actual spark and heat paths.
Administrative controls
Use a task-specific permit, competent preparation and fire watch through hand-back.
PPE
Provide assessed residual protection; it does not prevent ignition of nearby stock.
Verify, communicate and hand back
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.
What is control of ignition sources and hot work?
It is the prevention and management of work or conditions that could ignite combustible or explosive materials.
The control starts by identifying fuels: ordinary combustibles, flammable liquids, vapours, gases, mists, combustible dusts, residues, packaging, insulation, timber, roof materials, cable trays, oils, greases and waste. Then identify ignition sources that could meet those fuels during normal work, maintenance, cleaning, shutdown, construction or emergency repairs.
Hot work is a special case because it deliberately introduces heat, flame or sparks. A robust system asks whether hot work can be eliminated, whether the item can be moved to a safe area, whether fuels and residues can be removed, whether isolation and gas testing are adequate, whether the permit area includes hidden spaces and whether someone will keep watch long enough after the work.
Ignition source and hot-work scope
Area
Examples
Typical controls
Open flames and hot work
Welding, cutting, brazing, soldering, torches and heat guns.
Avoidance, permit, shielding, fire watch and gas testing.
Mechanical sparks and friction
Grinding, abrasive cutting, seized bearings and metal impact.
Tool selection, maintenance, exclusion zones and housekeeping.
Electrical ignition
Damaged cables, overloaded circuits, temporary electrics and non-ATEX equipment.
Inspection, maintenance and suitable equipment.
Static electricity
Liquid transfer, powder handling and synthetic materials.
Bonding, earthing, humidity and transfer controls.
Hot surfaces
Exhausts, heaters, ovens, lamps, motors and process equipment.
Temperature control, separation and guarding.
Smoking and arson opportunity
Smoking materials, poor security and waste near buildings.
No-smoking controls, security and waste management.
How can the ISO 45001 hierarchy of controls prevent ignition during hot work?
Eliminate ignition demand where feasible, then reduce fuel and exposure, engineer isolation, use permit discipline, and reserve PPE for residual hazards.
For the solvent-line repair, the cold method removes the ignition source. If welding is unavoidable, drain and isolate material, verify atmosphere and spark containment, and assign the issuer, welder and fire watcher distinct checks. The HSE permit guidance supports controlled ignition; the NI DSEAR rule is the local statutory route. Hold work if any boundary or test fails.
On a small screen, scroll this table sideways to read all columns.
How can the ERICPD hierarchy of controls prevent ignition during hot work?
ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.
Worked activity: Task application for How should ignition sources and hot work be controlled?
Activity and release context
For the solvent-line repair, the cold method removes the ignition source. If welding is unavoidable, drain and isolate material, verify atmosphere and spark containment, and assign the issuer, welder and fire watcher distinct checks. The HSE permit guidance supports controlled ignition; the NI DSEAR rule is the local statutory route. Hold work if any boundary or test fails.
Engineer records option; hold hot work while safe cold route works.
Substitute / reduce
Use lower-heat method after compatibility test.
Engineer approves trial; stop if new hazards are unassessed.
Engineering / isolate and control
Drain, isolate, clean, test and contain sparks.
Isolation authority verifies; stop on leak or failed gas test.
Administrative / discipline
Issue permit, define fire watch and hand-back.
Issuer checks area; stop on lost watch or changed work.
PPE / PPE
Residual welding and emergency protection.
Supervisor checks; no work if required protection fails.
How can the ISO 45001 hierarchy of controls prevent ignition during hot work?
The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").
Worked activity: Task application for How should ignition sources and hot work be controlled?
Activity and release context
For the solvent-line repair, the cold method removes the ignition source. If welding is unavoidable, drain and isolate material, verify atmosphere and spark containment, and assign the issuer, welder and fire watcher distinct checks. The HSE permit guidance supports controlled ignition; the NI DSEAR rule is the local statutory route. Hold work if any boundary or test fails.
Engineer records option; hold hot work while safe cold route works.
Substitute / reduce
Use lower-heat method after compatibility test.
Engineer approves trial; stop if new hazards are unassessed.
Engineering / isolate and control
Drain, isolate, clean, test and contain sparks.
Isolation authority verifies; stop on leak or failed gas test.
Administrative / discipline
Issue permit, define fire watch and hand-back.
Issuer checks area; stop on lost watch or changed work.
PPE / PPE
Residual welding and emergency protection.
Supervisor checks; no work if required protection fails.
The HSE five-level hierarchy orders elimination, substitution, engineering, administration and PPE; ERICPD helps apply it. A permit coordinates the solvent-line work after physical safeguards have been demonstrated.
For this line, the engineer establishes identity, connected feeds, actual contents and residues, pressure, volume and foreseeable changes before selecting the isolation and cleaning method. Record the isolation acceptance criteria and prove the relevant boundaries before intrusive work; do not infer an empty line from a pressure gauge alone. Select gas testing for the actual vapour, sample locations and any depleted oxygen after purging. Maintain isolation hardware, detectors and protective equipment with suitable service/calibration records. Immediately before work, verify isolation, cleanliness, atmosphere and spark protection of adjacent spaces; monitor integrity during the work and re-prove after unattended periods or shift changes as assessed. A leak, unsafe reading, changed work boundary or failed protection stops the job. Correct the cause, repeat the relevant checks and renew authorisation before restart; handback also verifies reinstatement. HSG253, isolation testing and monitoring supports this GB process-isolation basis; use the separate NI duties for NI work.
Applied case
A contractor proposes cutting a bracket near packaging stock and hidden voids. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.
Compare your decision
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.
Lesson 4
A damaged lead on a cleaning machine
Stop use, keep others from the defective equipment and arrange safe withdrawal and competent assessment.
Read the scene evidence
The machine has a damaged lead and is being taken towards a damp floor.
Identify the condition separately from the exposed person and any possible outcome.
How the harm pathway develops
Damaged electrical insulation on portable equipment
The machine has a damaged lead and is being taken towards a damp floor.
How people can be exposed
A person contacts exposed electrical parts or an energised conductive surface.
The machine has a damaged lead and is being taken towards a damp floor. The condition remains unresolved.
Protective response
Stop use, keep others from the defective equipment and arrange safe withdrawal and competent assessment.
Select controls by how they prevent harm
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.
Control level
Application to this case
Elimination
Remove the unnecessary trailing supply through a suitable task redesign.
Substitution
Compare suitable equipment for the wet and rough conditions of use.
Engineering controls
Provide properly designed electrical protection and protected cable routing.
Administrative controls
Use risk-based user checks, inspection, maintenance and clear defect control.
PPE
Electrical residual protection must be assessed; ordinary gloves do not make defective equipment safe.
Verify, communicate and hand back
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.
What is portable electrical equipment?
Portable electrical equipment is work equipment connected to an electrical supply by a plug and flexible cable and moved or handled during use or between uses.
Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.
Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.
Read all six steps as text
1. What is portable electrical equipment?
Portable electrical equipment is work equipment connected to an electrical supply by a plug and flexible cable and moved or handled during use or between uses.
Avoid / redesign: Eliminate: the project lead first asks whether the cutting can be completed off-site or by a pre-cut component.
Control the task: Isolate and engineer: route leads away from traffic and water, protect connectors and use supply protection selected by a competent electrical person.
Verify before release: Read the full task example, checks and stop points on this page.
Portable electrical equipment is work equipment connected to an electrical supply by a plug and flexible cable and moved or handled during use or between uses. Portable electrical equipment ranges from a static office charger to a hand-held tool or cleaning machine.
Apply it: Which part of this plan would you check at the workface before authorising the task?
2. Turn portable electrical equipment knowledge into a decision
Use the evidence to improve the actual work arrangement.
Change at source: Eliminate: the project lead first asks whether the cutting can be completed off-site or by a pre-cut component.
Make it observable: Read the full task example, checks and stop points on this page.
Keep useful evidence: Equipment specification, risk assessment, user check, defect quarantine, repair/test and return-to-use decision.
Portable electrical equipment ranges from a static office charger to a hand-held tool or cleaning machine. Damaged cables, unsuitable equipment and wet or rough use can allow shock, burns or fire; the maintenance decision depends on the equipment and the conditions of use. Equipment specification, risk assessment, user check, defect quarantine, repair/test and return-to-use decision.
Apply it: What evidence would show that the change improves this task, rather than only completing a record?
Fictional example: a practical application of the existing topic lesson.
Setting: Cleaning contractor uses a mains floor polisher at a wet entrance; supply, rating and cable route matter.
Act: Confirm suitability, route lead away from water and traffic, check plug/casing/lead and inspection history.
Hold / review: Crushed or exposed cable, wet connection or repeated trip; disconnect and quarantine.
Keep lead dry and protected, watch for damage or protective-device trips, keep others clear. Competent repair/inspection/test where needed, then supervisor releases the machine for use.
Apply it: At which point would you hold this example, and what evidence would allow it to proceed?
4. What determines inspection and testing frequency?
Connect the task, the route to the person and the control that can fail.
Source / exposure: Frequency should be based on equipment type, environment, use, movement, damage history and user competence.
Possible consequence: The most important shift for learners is this: there is no legal requirement for every portable appliance to be tested every year.
Control failure: The legal requirement is maintenance to prevent danger.
Frequency should be based on equipment type, environment, use, movement, damage history and user competence.
Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?
5. Choose controls for portable electrical equipment
Start with the stronger practicable options and verify their effect.
Eliminate: Eliminate: the project lead first asks whether the cutting can be completed off-site or by a pre-cut component.
Reduce: Substitute and reduce: if cutting remains, assess a suitable lower-voltage or battery tool for the material, runtime and environment.
Isolate: Isolate and engineer: route leads away from traffic and water, protect connectors and use supply protection selected by a competent electrical person.
Control: Control, PPE and Discipline: brief users on checks, keep a defect route and authorise repairs and testing to people with the required competence.
Eliminate: Eliminate: the project lead first asks whether the cutting can be completed off-site or by a pre-cut component. Reduce: Substitute and reduce: if cutting remains, assess a suitable lower-voltage or battery tool for the material, runtime and environment. Isolate: Isolate and engineer: route leads away from traffic and water, protect connectors and use supply protection selected by a competent electrical person. Control: Control, PPE and Discipline: brief users on checks, keep a defect route and authorise repairs and testing to people with the required competence. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.
Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?
Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.
The risk profile varies enormously. A laptop power supply in a dry office is not the same as a 230 V pressure washer used outdoors, an angle grinder on a construction site, a floor polisher used by a cleaning contractor, a catering extension lead, or a battery charger in a workshop. HSG107 is important because it moves the topic away from automatic annual testing and towards risk-based maintenance.
The main hazards are electric shock, burns, arcing, fire, trip hazards, equipment failure and secondary injury. Damage often occurs to plugs, flexible cables, strain relief, casing, switches, extension leads and equipment used in wet, dusty, hot, abrasive or outdoor environments.
Good management is a system: select suitable equipment, provide safe supply, train users, carry out user checks, complete formal visual inspections, test where justified, keep records proportionate, quarantine defects and review frequencies after damage or incidents.
Topic
What it means
Management implication
Portable equipment
Equipment moved or handled and connected by plug and cable.
Likely to suffer damage, so needs checks and maintenance.
Transportable equipment
Equipment moved between locations but not necessarily hand-held during use.
Assess travel, set-up, cable route and supply.
User check
Simple pre-use look and feel check by the user.
Find obvious damage before use.
Formal visual inspection
Recorded inspection by a competent person.
Find damage users may miss.
Combined inspection and test
Electrical tests plus inspection where risk justifies it.
Use risk-based intervals, not automatic annual PAT.
RCD
Residual current device that disconnects supply quickly after some faults.
Useful additional protection, not a substitute for safe equipment.
Inspection/test records and labels are useful management evidence, but there is no automatic standalone legal requirement to record every PAT activity or attach a sticker. Other applicable inspection duties may require records. Evidence should support the maintenance decision, not replace a present-condition check.
How should portable electrical equipment be controlled?
Control starts with suitable equipment and safe supply before inspection and testing.
This section turns legal language into workplace control. The examples show how broad duties become risk assessment, competent help, consultation, maintenance and review evidence.
Control layer
Practical example
Evidence
Eliminate the local cutting task / distinguish substitution
Use pre-cut components or avoid local cutting where feasible. Battery, lower-voltage or pneumatic alternatives are substitution choices for the assessed task; a battery may remove a trailing mains lead but leaves cutting, electrical/thermal and other risks.
Task design review.
Select suitable equipment
Correct voltage, IP rating, class, cable and duty rating.
Procurement specification.
Safe supply
Suitable sockets, transformers, RCDs and protected circuits.
Electrical installation/temporary supply record.
Protect from damage
Cable management, guards, routing and storage.
Workplace inspection.
User checks
Pre-use checks and defect reporting.
Briefing and observation.
Formal inspection/testing
Risk-based inspection and testing by competent people.
Register, inspection and test records.
Defect control
Quarantine, repair, retest or disposal.
Defect log and close-out.
Applied case
The machine has a damaged lead and is being taken towards a damp floor. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.
Compare your decision
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.
Lesson 5
A noisy task beside another workstation
Arrange assessment and suitable control of the noisy task and nearby exposure; do not treat discomfort alone as an exposure measurement.
Read the scene evidence
A noisy tool is being used next to a staffed desk without an exposure assessment.
Identify the condition separately from the exposed person and any possible outcome.
A noisy tool is being used next to a staffed desk without an exposure assessment. The condition remains unresolved.
Protective response
Arrange assessment and suitable control of the noisy task and nearby exposure; do not treat discomfort alone as an exposure measurement.
Select controls by how they prevent harm
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.
Control level
Application to this case
Elimination
Remove unnecessary noisy processing through suitable procurement or off-site preparation.
Substitution
Choose a suitable quieter process or tool using reliable task evidence.
Engineering controls
Enclose or isolate the source and maintain equipment to reduce noise.
Administrative controls
Assess representative exposure, separate people and verify the prevention and surveillance arrangements.
PPE
Use suitable hearing protection for remaining exposure with proper selection and use.
Verify, communicate and hand back
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.
What are the first decisions?
Identify the task and source, the people and duration, then decide whether action values or peaks may be reached and which source controls can be installed.
Best-practice guide · six simple steps
Best-practice guide: Noise at Work
Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.
Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.
Read all six steps as text
1. What are the first decisions?
Identify the task and source, the people and duration, then decide whether action values or peaks may be reached and which source controls can be installed.
Avoid / redesign: Remove an unnecessary compressed-air cleaning step and use a non-air cleaning method; process owner confirms product quality and other hazards.
Control the task: Enclose the saw, fit damping and place the compressor away from occupied work; engineer checks guarding, access and heat.
Verify before release: Observe the task and verify the compressor is not used; hold a reintroduced blow-off job.
Identify the task and source, the people and duration, then decide whether action values or peaks may be reached and which source controls can be installed. Noise at work can cause permanent hearing damage and make warnings harder to hear.
Apply it: Which part of this plan would you check at the workface before authorising the task?
Use the evidence to improve the actual work arrangement.
Change at source: Remove an unnecessary compressed-air cleaning step and use a non-air cleaning method; process owner confirms product quality and other hazards.
Make it observable: Observe the task and verify the compressor is not used; hold a reintroduced blow-off job.
Keep useful evidence: After: the manager accepts the new method only when product quality and noise are verified, updates the training and retains hearing surveillance for those still at risk.
Noise at work can cause permanent hearing damage and make warnings harder to hear. Identify noisy sources and exposed people, estimate daily or weekly and peak exposure, reduce sound at source, and apply the correct GB or NI action and surveillance duties. After: the manager accepts the new method only when product quality and noise are verified, updates the training and retains hearing surveillance for those still at risk.
Apply it: What evidence would show that the change improves this task, rather than only completing a record?
Fictional example: a workshop tests a non-air cleaning method.
Find: A blow-off gun operates beside a saw and nearby packers.
Change: Trial vacuum cleaning and a suitable quieter saw arrangement.
Verify: Measure realistic cutting and cleaning cycles before routine acceptance.
The engineer and noise assessor check the changed process under representative conditions. Product quality and new hazards still need review. The supervisor stops the task if an enclosure is removed, and the manager keeps the remaining protection and surveillance programme appropriate to the assessed exposure.
Apply it: Does the acceptance evidence cover the full task and the people nearby?
Connect the task, the route to the person and the control that can fail.
Exposure: Repeated noise exposure can permanently damage hearing.
Peaks: A high impulsive peak needs assessment as well as daily exposure.
Communication: Noise and poorly selected protection can interfere with warnings.
Identify the source, duration and people exposed, then assess daily or weekly exposure and peaks. Reduce noise at source and verify the residual exposure. A hearing test measures an outcome; it does not make the noisy process quieter.
Apply it: Which source can be removed or made quieter before relying on hearing protection?
Start with the stronger practicable options and verify their effect.
Eliminate: Remove an unnecessary compressed-air cleaning step and use a non-air cleaning method; process owner confirms product quality and other hazards.
Substitution: Procure a lower-noise saw or nozzle for the same output; buyer and engineer compare supplier data under the intended load.
Engineering: Enclose the saw, fit damping and place the compressor away from occupied work; engineer checks guarding, access and heat.
Administrative: Supervisor limits time in the remaining noisy area and marks access; exposure assessor calculates actual full-shift exposure.
PPE plus upkeep: Fit suitable hearing protection for residual noise and teach seal checks.
Eliminate: Remove an unnecessary compressed-air cleaning step and use a non-air cleaning method; process owner confirms product quality and other hazards. Substitution: Procure a lower-noise saw or nozzle for the same output; buyer and engineer compare supplier data under the intended load. Engineering: Enclose the saw, fit damping and place the compressor away from occupied work; engineer checks guarding, access and heat. Administrative: Supervisor limits time in the remaining noisy area and marks access; exposure assessor calculates actual full-shift exposure. PPE plus upkeep: Fit suitable hearing protection for residual noise and teach seal checks. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.
Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?
Follow the official sources below and retain the task-specific evidence.
Official guidance: HSE noise risk assessment
Official guidance: HSE buy quiet guidance
Task decision: After: the manager accepts the new method only when product quality and noise are verified, updates the training and retains hearing surveillance for those still at risk.
Apply it: Which official source and full-topic section will you use to resolve the next decision?
Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.
An employee does not need to prove a hearing diagnosis to report a noisy task. A supervisor should pause an uncontrolled new process, consult the noise assessment and protect nearby people. A manager gives the action plan an owner and checks whether a quiet alternative or enclosure works in actual use. Sources: HSE noise risk assessment, HSE buy quiet guidance.
How can the ISO 45001 hierarchy of controls reduce workplace noise at source and protect hearing?
Remove an unnecessary noisy task, buy quieter equipment, enclose or damp the source, then limit residual exposure and fit hearing protection.
HSE prioritises eliminating and substituting hazards before engineering controls, administrative controls and PPE, as explained in its five-level hierarchy of controls. SHARE uses ERICPD as a task-planning prompt: Eliminate; Reduce, including substitution; Isolate through engineered separation; Control with other engineered or administrative measures; PPE; and Discipline, meaning continued verification and maintenance. ERICPD is not a sixth HSE level or a separate legal duty. The example below is a feasibility test for this work, not a universal prescription.
How can the ERICPD hierarchy of controls reduce workplace noise at source and protect hearing?
ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.
Worked activity: Task application for Noise at Work
Activity and release context
A site plan should state who installs each source measure, where measurements will be repeated and what stops operation. Protectors support the plan; they do not turn an untreated noisy machine into acceptable source control. Sources: HSE noise construction controls , HSE noise hearing protection .
Remove an unnecessary compressed-air cleaning step and use a non-air cleaning method; process owner confirms product quality and other hazards.
Observe the task and verify the compressor is not used; hold a reintroduced blow-off job. Sources: HSE; HSENI.
Reduce
Procure a lower-noise saw or nozzle for the same output; buyer and engineer compare supplier data under the intended load.
Acceptance measurement at the operator position; reject an unverified noisy replacement. Sources: HSE; HSENI.
Engineering
Enclose the saw, fit damping and place the compressor away from occupied work; engineer checks guarding, access and heat.
Measure outside the enclosure and check door seals; failed enclosure or new rattling stops use. Sources: HSE; HSENI.
Administrative
Supervisor limits time in the remaining noisy area and marks access; exposure assessor calculates actual full-shift exposure.
Observe access and repeat exposure estimate after changed shifts; duration alone is not source control. Sources: HSE; HSENI.
PPE
Fit suitable hearing protection for residual noise and teach seal checks.
Inspect fit and use; surveillance trend or defect restarts the source-control review. Sources: HSE; HSENI.
Discipline / continuing assurance
Continuing checks mean maintenance, supervision and learning after the stronger controls.
How can the ISO 45001 hierarchy of controls reduce workplace noise at source and protect hearing?
The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").
Worked activity: Task application for Noise at Work
Activity and release context
A site plan should state who installs each source measure, where measurements will be repeated and what stops operation. Protectors support the plan; they do not turn an untreated noisy machine into acceptable source control. Sources: HSE noise construction controls , HSE noise hearing protection .
Remove an unnecessary compressed-air cleaning step and use a non-air cleaning method; process owner confirms product quality and other hazards.
Observe the task and verify the compressor is not used; hold a reintroduced blow-off job. Sources: HSE; HSENI.
Substitution
Procure a lower-noise saw or nozzle for the same output; buyer and engineer compare supplier data under the intended load.
Acceptance measurement at the operator position; reject an unverified noisy replacement. Sources: HSE; HSENI.
Engineering
Enclose the saw, fit damping and place the compressor away from occupied work; engineer checks guarding, access and heat.
Measure outside the enclosure and check door seals; failed enclosure or new rattling stops use. Sources: HSE; HSENI.
Administrative
Supervisor limits time in the remaining noisy area and marks access; exposure assessor calculates actual full-shift exposure.
Observe access and repeat exposure estimate after changed shifts; duration alone is not source control. Sources: HSE; HSENI.
PPE
Fit suitable hearing protection for residual noise and teach seal checks.
Inspect fit and use; surveillance trend or defect restarts the source-control review. Sources: HSE; HSENI.
Administrative controls / continuing assurance
Continuing checks mean maintenance, supervision and learning after the stronger controls.
A site plan should state who installs each source measure, where measurements will be repeated and what stops operation. Protectors support the plan; they do not turn an untreated noisy machine into acceptable source control. Sources: HSE noise construction controls, HSE noise hearing protection.
Match the control to the path. Damping reduces vibration of a resonant panel; a silencer reduces air-flow or exhaust noise; insulation and a sealed enclosure block sound transmission; absorptive lining reduces reflected sound in a room but may do little to the direct path beside a saw. The engineer tests the actual frequency and operating mode, then confirms the reduction at the worker position. HSE source-control methods
Read the practical categories separately: elimination removes the hazardous task/source; substitution replaces it with a suitable safer alternative; physical separation, containment and capture are engineering decisions. Duration/access/briefing are administrative measures, PPE covers residual exposure, and continued inspection, maintenance and verified action closure sustain the controls. Exposure monitoring or dosimetry measures exposure rather than protecting a person. The detailed text and records below distinguish these decisions; an overview illustration is not task authorisation.
Applied case
A noisy tool is being used next to a staffed desk without an exposure assessment. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.
Compare your decision
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.
Lesson 6
Unplanned extra time on a vibrating tool
Review and control the actual task and exposure, act on symptoms and defects, and arrange appropriate competent support.
Read the scene evidence
A worker has taken on additional tool work and the actual daily use has not been reviewed.
Identify the condition separately from the exposed person and any possible outcome.
A worker has taken on additional tool work and the actual daily use has not been reviewed. The condition remains unresolved.
Protective response
Review and control the actual task and exposure, act on symptoms and defects, and arrange appropriate competent support.
Select controls by how they prevent harm
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.
Control level
Application to this case
Elimination
Eliminate unnecessary vibrating-tool work through process or component redesign.
Substitution
Choose a suitable lower-vibration method using representative task data.
Engineering controls
Use appropriate fixtures and maintained tools that reduce exposure at source.
Administrative controls
Assess real daily use, plan work and apply suitable symptom and health-surveillance arrangements.
PPE
Gloves do not provide a dependable vibration exposure control.
Verify, communicate and hand back
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.
What is hand-arm vibration and whole-body vibration?
HAV enters through hands holding or guiding vibrating tools or workpieces; WBV enters mainly through a seat or feet while operating vehicles or mobile machinery.
Best-practice guide · six simple steps
Best-practice guide: Vibration at Work
Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.
Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.
Read all six steps as text
1. What is hand-arm vibration and whole-body vibration?
HAV enters through hands holding or guiding vibrating tools or workpieces; WBV enters mainly through a seat or feet while operating vehicles or mobile machinery.
Avoid / redesign: Avoid unnecessary vibrating work
Control the task: Use supported tools, sound consumables and maintained vehicle routes
Verify before release: Avoid unnecessary vibrating work
HAV enters through hands holding or guiding vibrating tools or workpieces; WBV enters mainly through a seat or feet while operating vehicles or mobile machinery. Hand-arm vibration (HAV) reaches the hands through powered tools or workpieces; whole-body vibration (WBV) reaches a seated or standing person through a vehicle or platform.
Apply it: Which part of this plan would you check at the workface before authorising the task?
2. Turn vibration at work knowledge into a decision
Use the evidence to improve the actual work arrangement.
Change at source: Avoid unnecessary vibrating work
Make it observable: Avoid unnecessary vibrating work
Keep useful evidence: Assessment inputs, HSE calculator result, plan change, defect/repair and supervisor decision.
Hand-arm vibration (HAV) reaches the hands through powered tools or workpieces; whole-body vibration (WBV) reaches a seated or standing person through a vehicle or platform. Repeated exposure can damage hand nerves and circulation or contribute to back pain, while shocks and posture add to vehicle risk. Assessment inputs, HSE calculator result, plan change, defect/repair and supervisor decision.
Apply it: What evidence would show that the change improves this task, rather than only completing a record?
Fictional example: a practical application of the existing topic lesson.
Setting: Concrete anchor drilling and steel-bracket grinding on a fictional construction site.
Act: Check bits/discs, work support and actual trigger-time estimates for both tools; 5 m/s² for two drilling hours alone reaches 100 points.
Hold / review: Hold if combined exposure cannot be defended, controls fail or planned exposure approaches the ELV.
Record real trigger time and add grinding exposure; stop for blunt bits, extra work or abnormal vibration. Log times and condition; replan remaining work or release sound equipment for next user.
Apply it: At which point would you hold this example, and what evidence would allow it to proceed?
Connect the task, the route to the person and the control that can fail.
New HAV symptoms: Report, review exposure and refer through OH route.
White fingers or lost dexterity: Do not treat this as ordinary cold or fatigue; assess promptly.
Back pain after repeated jolts: Review route, machine, seat, speed and other back-pain factors.
New HAV symptoms: Report, review exposure and refer through OH route. White fingers or lost dexterity: Do not treat this as ordinary cold or fatigue; assess promptly. Back pain after repeated jolts: Review route, machine, seat, speed and other back-pain factors.
Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?
Start with the stronger practicable options and verify their effect.
Avoid: Avoid unnecessary vibrating work
Substitute or reduce: Choose an efficient lower-vibration method for the task
Engineer: Use supported tools, sound consumables and maintained vehicle routes
Organise and verify: Assess each person’s combined day and stop for symptoms or changed exposure
Protect residual exposure: Gloves do not establish vibration compliance
Avoid: Avoid unnecessary vibrating work Substitute or reduce: Choose an efficient lower-vibration method for the task Engineer: Use supported tools, sound consumables and maintained vehicle routes Organise and verify: Assess each person’s combined day and stop for symptoms or changed exposure Protect residual exposure: Gloves do not establish vibration compliance Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.
Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?
Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.
A breaker, grinder, drill, sander or hand-guided compactor can create HAV. A dumper, tractor, forklift or earth-moving machine on rough ground can create WBV and severe shocks. One person may experience both on a day, but the two exposure types have different assessment methods and legal values: do not add HAV and WBV numbers together. Noise, dust, force, posture and manual handling may need separate controls.
Start by avoiding the hazardous task or release, then use suitable substitution and physical controls before relying on work rules or personal protection.
The order guides a decision; the actual control depends on this task, the people exposed and what a change could introduce. A supervisor should observe the control during real work, hold a failed task and obtain a competent release after correction. HSE guidance for this control decision
Control layer
Task decision
Avoid
Avoid unnecessary vibrating work
Substitute or reduce
Choose an efficient lower-vibration method for the task
Engineer
Use supported tools, sound consumables and maintained vehicle routes
Organise and verify
Assess each person’s combined day and stop for symptoms or changed exposure
Protect residual exposure
Gloves do not establish vibration compliance
Applied case
A worker has taken on additional tool work and the actual daily use has not been reviewed. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.
Compare your decision
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.
Lesson 7
Maintenance conflicts with warehouse traffic
Hold the conflicting activities and coordinate a safe work area, method, access and hand-back with the responsible people.
Read the scene evidence
A contractor has set up a repair across a route that remains in use.
Identify the condition separately from the exposed person and any possible outcome.
How the harm pathway develops
Uncoordinated contractor work and occupied operations
A contractor has set up a repair across a route that remains in use.
How people can be exposed
Workers, vehicles and contractor tools or temporary work meet at an uncontrolled interface.
Possible harm
Impact, falls, contact with work equipment or interrupted emergency access.
A contractor has set up a repair across a route that remains in use. The condition remains unresolved.
Protective response
Hold the conflicting activities and coordinate a safe work area, method, access and hand-back with the responsible people.
Select controls by how they prevent harm
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.
Control level
Application to this case
Elimination
Schedule or relocate the repair so it does not overlap occupied movements.
Substitution
Compare a suitable repair method that needs less intrusive temporary work.
Engineering controls
Provide suitable segregation and protected access around the work.
Administrative controls
Agree scope, competence, site hazards, interfaces, supervision and safe hand-back.
PPE
Use assessed task protection; a contractor induction alone does not control the live interface.
Verify, communicate and hand back
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.
What is contractor safety?
Contractor safety is the end-to-end control of risks linked to contracted work, from need definition through to post-job learning.
A contractor is an individual or organisation engaged to carry out work or provide a service. Contractors may work on site, remotely, in a shared workplace, on construction projects, on plant and equipment, in customer-facing environments, or as part of specialist services such as cleaning, security, asbestos, electrical work, scaffolding, transport, maintenance or design.
Contractor safety is wider than checking insurance and collecting a risk assessment. It asks whether the work is needed, what can go wrong, who controls the work area, what information the contractor needs, whether the contractor is competent for this specific work, how interfaces will be managed, who supervises, and what evidence proves the controls are working.
The standard should be proportionate. A small supplier delivering stationery does not need the same system as a contractor carrying out hot work in a live plant room. The discipline is matching the management effort to the credible risk.
Contractor safety overview
Element
What it means
Why it matters
Planning
Define the work, risks, site constraints and expected standard.
Prevents poor scope and unsafe assumptions.
Selection
Check capability, competence, resources and experience.
Avoids appointing contractors who cannot manage the risk.
Coordination
Agree who does what, when and how.
Controls interfaces and simultaneous activities.
Communication
Share site hazards, emergency arrangements and rules.
Prevents unfamiliarity becoming risk.
Monitoring
Check workface controls and contractor performance.
Finds drift before harm occurs.
Review
Capture learning, defects and performance after completion.
Improves future appointments and standards.
Applied case
A contractor has set up a repair across a route that remains in use. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.
Compare your decision
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.
Lesson 8
An unverified grinding wheel is fitted
Do not run the machine. Have a competent authorised person verify the wheel, fitting, guarding and task controls.
Read the scene evidence
A replacement wheel has unclear markings and has not been checked against the machine or material.
Identify the condition separately from the exposed person and any possible outcome.
How the harm pathway develops
A rotating abrasive wheel whose suitability and condition are uncertain
A replacement wheel has unclear markings and has not been checked against the machine or material.
How people can be exposed
A mismatched, damaged or poorly fitted wheel is run near people.
Possible harm
Wheel fragments, contact injury or exposure to sparks and dust.
A replacement wheel has unclear markings and has not been checked against the machine or material. The condition remains unresolved.
Protective response
Do not run the machine. Have a competent authorised person verify the wheel, fitting, guarding and task controls.
Select controls by how they prevent harm
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.
Control level
Application to this case
Elimination
Avoid unnecessary cutting or grinding through component and process redesign.
Substitution
Compare a suitable lower-hazard preparation method.
Engineering controls
Provide a correctly matched wheel and machine with suitable guarding and source controls.
Administrative controls
Verify markings, condition, speed compatibility, fitting competence and the actual work setup.
PPE
Select suitable eye, face and other protection for remaining exposure; PPE does not make an unsuitable wheel safe.
Verify, communicate and hand back
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.
What is the scope and authority of this page?
The selection, guarding, mounting, use and maintenance principles apply across the UK, while Great Britain and Northern Ireland have separate workplace and product-supply routes. This is an educational reference; the actual wheel, machine and material instructions govern compatibility and limits.
Use HSG17 within its scope. HSE publishes it as technical abrasive-wheel guidance from 2000. Apply its wheel selection, mounting, guarding and use principles alongside current PUWER, COSHH, noise and vibration duties and the current manufacturer instructions; an older guide must not override a newer legal requirement or product limit.
Great Britain
For England, Scotland and Wales, the main work-equipment route is the Provision and Use of Work Equipment Regulations 1998 (PUWER), supported by HSE guidance and other GB regulations for substances, noise, vibration and personal protective equipment.
Northern Ireland
Northern Ireland has its own legislation, including the Provision and Use of Work Equipment Regulations (Northern Ireland) 1999, with guidance and enforcement led by HSENI. Do not use a GB citation as though it were the NI legal text.
When to recheck
Reassess wheel compatibility and controls after a changed tool, wheel, material, work method, damage or near miss. Check current law, guidance and manufacturer instructions before the task.
When markings, speed, material, guard condition or jurisdiction conflict, hold the task and obtain competent advice before use.
The guide distinguishes operator decisions from wheel mounting, supervision, procurement and specialist exposure control. A product mark, training certificate or completed form alone does not prove the combination is safe for the task.
What should be checked before abrasive wheel work starts?
Before energising the tool, check the person, task, machine, wheel or disc, mounting, guard, work area and exposure controls as one complete system.
A pre-use check is a deliberate start-work decision, not a glance at a sticker. The operator should be able to identify the material and operation, read the wheel marking, prove that the machine cannot overspeed the wheel, inspect both tool and disc, confirm that guards and handles are fitted, secure the workpiece and control dust, sparks, noise, vibration and nearby people. The manufacturer's instructions and the local risk assessment or method statement set the minimum for the particular tool.
Use a simple sequence: plan the cut or grind; isolate and inspect the tool; select and inspect the correct wheel; mount it using the specified components; restore the guard and controls; prepare the work area; carry out a controlled trial run; then start work only if the set-up remains stable. Any uncertainty about identity, damage, speed, fit, mounting or control is a stop-work reason.
Tool and machine pre-use checks
Tool and machine pre-use checks before abrasive wheel work
Tool check
What to inspect
Stop work when
Identity, rating and instructions
Confirm the tool is the approved type for the task, its identification and speed plate are legible, and the correct manufacturer instructions are available. Check that any inspection or maintenance status remains valid.
The tool is unidentifiable, modified, outside its inspection regime or being used for a purpose the manufacturer does not allow.
Body, spindle and bearings
Look for cracks, loose parts, damaged threads, excessive spindle play, abnormal noise, overheating, blocked ventilation slots or evidence that the tool has been dropped.
The spindle is bent or loose, threads are damaged, the body is cracked, parts are missing, or rotation is rough or noisy.
Guard and auxiliary handle
Use the guard specified for the machine and wheel. Secure and position it between the operator and the wheel as intended. Fit the side handle and make sure both can resist normal working forces.
The guard or handle is missing, loose, damaged, altered, the wrong size, tied back or prevents the task from being done safely.
Switches and controls
Check the on/off, hold-to-run, trigger lock, emergency stop and braking arrangements provided for the machine. The control should operate freely and return as designed.
A switch sticks, a safety control is defeated, the machine can start unexpectedly or the wheel does not stop in the expected manner.
Power source
For electric tools, inspect the plug, cable, battery and charger. For pneumatic tools, inspect hoses, couplings and pressure controls. For petrol saws, check fuel, leaks, caps, controls and exhaust condition.
There are exposed conductors, damaged batteries, leaking fuel, insecure hoses, unsuitable pressure, makeshift repairs or an incompatible power supply.
Dust and water controls
Check that extraction shrouds, hoses, filters, vacuums, water feeds, flow controls and electrical protection are compatible, connected and able to control the material being cut.
Controls are missing, blocked, leaking, incompatible, have no adequate water flow or extraction, or would introduce electrical, slip or contamination risk.
Fixed grinders and cutting machines
Check secure anchoring, guard enclosure, transparent screens, work rests, clamps and interlocks. Keep work rests close to the wheel and adjust them only while isolated and stationary.
The machine moves, the work rest or clamp is loose, the gap can trap the workpiece, an interlock is defeated or the wheel fouls the guard.
Wheel, cutting disc and mounting checks
Pre-use, mounting and guarding checks for abrasive wheels
Check area
What good looks like
Why it matters
Wheel and disc selection
The wheel matches the material, machine, bore size, dimensions, task, wet or dry use, and maximum rotational speed.
Wrong selection can lead to overheating, binding, excessive dust, wheel loading, burst or loss of control.
Markings and condition
Markings are legible, expiry or use-by dates are checked where relevant, and the wheel is free from cracks, chips, damp, warping or contamination.
A damaged or aged wheel may fail even if the machine and operator are otherwise suitable.
Ring test where appropriate
A suitable dry vitrified wheel is gently tapped with a non-metallic implement and its sound is compared with other sound wheels of the same lot and specification; a dull or suspicious response means rejection.
The test can reveal internal cracking in some wheel types, but it is not suitable for thin resin cutting discs or many small mounted wheels.
Flanges, blotters and bushes
Correct flanges, blotters and bushes are used only where required by the wheel and machine manufacturer, and the wheel is secured without over-tightening.
Poor mounting concentrates stress around the bore and can crack the wheel before work starts.
Guards, handles and rests
Guards and side handles are fitted. Bench grinder rests and tongue guards are adjusted as the wheel wears.
Guarding reduces contact and fragment exposure; poor rest adjustment can pull the workpiece into the wheel.
Test run and work area
Newly mounted wheels are run in a safe direction with people clear, then the work area is checked for dust control, sparks, cables, combustibles and bystanders.
Test running and work-area planning reveal defects before full cutting or grinding load is applied.
Ring-test limitation: only use a ring test where the wheel type and manufacturer permit it and the person is trained in the method. HSG17 lists several products for which it is not practicable, including small wheels, plugs, cones, mounted wheels, segments and plate-mounted wheels. A ring test never overrides visible damage, doubtful history or the manufacturer's rejection criteria.
Start-up, work area and stop-work checks
Start-up, work area and stop-work checks for abrasive wheel tasks
Stage
Required check
Operational decision
Workpiece and line of cut
Support and clamp the work so it cannot move, close on the wheel or release stored energy. Check both sides of the cut for services, fixings, voids and people.
Re-plan if the cut can trap the wheel, destabilise the material or direct fragments towards anyone.
Dust, fume and debris
Identify what the material and any coating contain. Start source control before cutting, verify water flow or extraction capture, and use suitable face-fitted RPE where residual exposure remains.
Do not start if the material is unknown, control is ineffective, visible dust escapes or contaminated dust would spread to others.
Sparks, heat and fire
Trace the spark path and check above, below and behind the work. Remove or protect combustibles, control flammable substances and arrange permits, extinguishers and a fire watch where required.
Stop if sparks can enter a void, reach fuel, vapour, dust or insulation, or fall into an uncontrolled area.
People and access
Create an exclusion zone for the wheel plane, kickback path, sparks, dust and ejected material. Protect people on adjacent work faces and prevent unplanned entry.
Delay work where the area cannot be segregated or the operator cannot maintain stable footing and two-handed control.
PPE and compatibility
Use impact-rated eye protection and any required face, hearing, respiratory, foot and body protection. Select gloves only where they help without creating an entanglement or loss-of-grip risk.
Do not proceed if the required items do not fit, are damaged or interfere with each other, the respirator seal or safe tool control.
Trial run after fitting
With the guard secured, hold or stand out of the wheel plane, keep others clear and run the wheel without load for the manufacturer-specified period. Listen and watch for wobble, vibration, rubbing or abnormal noise.
Isolate immediately if the wheel runs untrue, vibrates, contacts the guard, sounds abnormal or the machine cannot reach stable speed.
During use and after stopping
Let the wheel do the work; avoid forcing, twisting or side-loading a cutting disc. Maintain controls until the wheel stops and place the tool so the wheel cannot contact anything.
Stop for binding, slowing, unusual heat, smell, change in sound, damaged control equipment, movement of the workpiece or changed site conditions.
Quarantine rule: a dropped, cracked, chipped, warped, contaminated, water-damaged, overheated, unmarked or out-of-date wheel should not be tried “just once”. Isolate the tool, label the defect, prevent reuse and follow the organisation's competent-person and disposal process.
Applied case
A replacement wheel has unclear markings and has not been checked against the machine or material. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.
Compare your decision
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.
Lesson 9
An oxygen connection is treated like ordinary air
Keep the equipment out of use and refer the complete assembly to the competent contractor and gas supplier. Do not try the fitting, lubricate it or improvise an adapter.
Read the scene evidence
A contractor proposes fitting a spare regulator to an oxygen cylinder because the connector appears to fit. The part has been stored beside oily tools and its oxygen-service suitability is unknown.
Identify the condition separately from the exposed person and any possible outcome.
How the harm pathway develops
An oxygen connection has unverified compatibility and possible oil contamination.
A contractor proposes fitting a spare regulator to an oxygen cylinder because the connector appears to fit. The part has been stored beside oily tools and its oxygen-service suitability is unknown.
How people can be exposed
Contamination or unsuitable equipment can meet oxygen under pressure; a leak can enrich the nearby atmosphere.
Possible harm
Oxygen can make materials ignite more readily and burn fiercely; it is an oxidiser, not a fuel.
A contractor proposes fitting a spare regulator to an oxygen cylinder because the connector appears to fit. The part has been stored beside oily tools and its oxygen-service suitability is unknown. The condition remains unresolved.
Protective response
Keep the equipment out of use and refer the complete assembly to the competent contractor and gas supplier. Do not try the fitting, lubricate it or improvise an adapter.
Select controls by how they prevent harm
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.
Control level
Application to this case
Elimination
Consider a task method that removes the need for oxygen equipment at this location.
Substitution
Select a suitable alternative process only after its hazards and work quality have been assessed.
Engineering controls
Use a complete compatible oxygen-service assembly with contamination control and suitable ventilation.
Administrative controls
Check the gas label, supplier instructions, equipment condition and competence before authorisation; connector fit alone proves nothing.
PPE
Use assessed protection for the authorised task; PPE cannot establish oxygen compatibility or prevent enrichment.
Verify, communicate and hand back
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.
How do different gases cause harm?
Identify the gas from its label and supplier information before choosing equipment or controls. Flammability, toxicity, oxygen displacement, oxidising power and stored pressure are different hazards and may occur together.
A fuel gas mixed with air can ignite; confinement can turn rapid burning into a damaging pressure rise. A leaking non-flammable gas can still displace oxygen. Oxygen is not a fuel, but an oxygen-enriched atmosphere makes materials ignite more readily and burn fiercely. No smell does not prove a space is safe.
Usually mainly methane and lighter than air. It can still collect in enclosed high spaces or migrate through voids; do not assume it will disperse safely.
LPG such as propane or butane
Stored as a liquid under pressure; released vapour is heavier than air and can accumulate in pits, drains and basements. Choose siting and ventilation for that behaviour. HSE LPG guidance.
Carbon monoxide
A poisonous combustion product, not the odour added to some fuel gases. It can reach occupied areas through a defective flue or inadequate ventilation.
Oxygen and fuel gas welding sets
Control each gas separately: compatible clean equipment, cylinder security, flashback protection and hot-work precautions. Never use oxygen for ventilation or cleaning clothing.
Inert compressed gases or cryogenic liquids
Oxygen displacement and stored-pressure risks remain even when there is no fire hazard. Cryogenic liquids also cause cold injury; obtain specialist system and emergency advice.
A cylinder colour, a fitting that appears to connect, or a product conformity mark is not proof of compatibility. Read the gas label, appliance data and current manufacturer or supplier instructions together.
How should gas risks be reduced?
First ask whether the gas or hot-work task can be removed. Where it remains, reduce the potential release, contain and isolate the supply, control ignition and combustion, and plan for failure before relying on instructions or PPE.
For a temporary event, a suitable electric cooking option may remove the need for LPG cylinders and hoses, although electrical capacity and other hazards still need checking. For fabrication, a cold-cutting method may avoid oxy-fuel hot work. If gas is necessary, competent design and installation should provide appropriate containment, ventilation, flues, isolation and protective devices.
Keep quantities proportionate to the work, protect pipework and cylinders from vehicles and heat, and control ignition sources where a release could create an explosive atmosphere. Establish who owns ventilation and safety interlocks, and how faults are reported and repaired. Never defeat an interlock to keep production running. DSEAR assessment determines prevention and mitigation measures; a generic separation distance or gas alarm setpoint is not a substitute. HSE Dangerous Substances and Explosive Atmospheres Regulations.
Administrative controls then support the engineered precautions: authorise work, coordinate contractors, check changes, maintain the system and practise evacuation. Use suitable eye, hand, body and other protection for identified residual hazards such as hot work or cylinder handling. Ordinary masks and gloves cannot make an unsafe gas atmosphere acceptable. Escape, emergency intervention and confined-space rescue need separately planned competent arrangements.
Applied case
A contractor proposes fitting a spare regulator to an oxygen cylinder because the connector appears to fit. The part has been stored beside oily tools and its oxygen-service suitability is unknown. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.
Compare your decision
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.
Lesson 10
Shift handover: connect the hazards
Defend the stopping condition and the evidence needed for release.
Reconstruct the whole task
A contractor arrives to repair equipment while production continues nearby. Hot work, a damaged extension lead, a noisy tool and an oxygen set share the workshop.
The contractor has signed the job sheet, but a guard is absent and the warehouse shift has not received the handback information.
Keep the equipment unavailable until reinstatement, protective measures and the controlled handback are verified.
Build an evidence-led handover
Item
What the receiver needs
Task and location
Warehouse maintenance and workshop safety — identify the affected people and boundaries.
Actual condition
The contractor has signed the job sheet, but a guard is absent and the warehouse shift has not received the handback information.
Control and current restriction
Keep the equipment unavailable until reinstatement, protective measures and the controlled handback are verified.
Verification and owner
Name the responsible role and the task-specific evidence. Keep unresolved matters open.
Use the documents as working tools
Map the task, people, exposure pathway, existing controls, missing evidence and review trigger. Use the fictional course case.
Prepare a five-minute task briefing. Ask a scenario question and check understanding, rather than relying on an attendance signature.
Find who owns the control, who can authorise release and how a worker escalates a defect. Check the actual local arrangements.
Compare a claim with an observation, a relevant record and a competent explanation. Record open actions and verify closure.
How do different gases cause harm?
Identify the gas from its label and supplier information before choosing equipment or controls. Flammability, toxicity, oxygen displacement, oxidising power and stored pressure are different hazards and may occur together.
A fuel gas mixed with air can ignite; confinement can turn rapid burning into a damaging pressure rise. A leaking non-flammable gas can still displace oxygen. Oxygen is not a fuel, but an oxygen-enriched atmosphere makes materials ignite more readily and burn fiercely. No smell does not prove a space is safe.
Usually mainly methane and lighter than air. It can still collect in enclosed high spaces or migrate through voids; do not assume it will disperse safely.
LPG such as propane or butane
Stored as a liquid under pressure; released vapour is heavier than air and can accumulate in pits, drains and basements. Choose siting and ventilation for that behaviour. HSE LPG guidance.
Carbon monoxide
A poisonous combustion product, not the odour added to some fuel gases. It can reach occupied areas through a defective flue or inadequate ventilation.
Oxygen and fuel gas welding sets
Control each gas separately: compatible clean equipment, cylinder security, flashback protection and hot-work precautions. Never use oxygen for ventilation or cleaning clothing.
Inert compressed gases or cryogenic liquids
Oxygen displacement and stored-pressure risks remain even when there is no fire hazard. Cryogenic liquids also cause cold injury; obtain specialist system and emergency advice.
A cylinder colour, a fitting that appears to connect, or a product conformity mark is not proof of compatibility. Read the gas label, appliance data and current manufacturer or supplier instructions together.
Applied case
The contractor has signed the job sheet, but a guard is absent and the warehouse shift has not received the handback information.
Compare your decision
Keep the equipment unavailable until reinstatement, protective measures and the controlled handback are verified.
Keep the equipment unavailable until reinstatement, protective measures and the controlled handback are verified.
Lesson 11
Your workplace transfer challenge
Turn one lesson into a bounded check with an owner and a review trigger.
Prepare a useful task briefing
Coordinate isolation, contractors and specialist tools.
Use the printable course workbook to describe one fictional task. State who could be exposed, the harmful mechanism, a higher-level control, the immediate restriction and the evidence needed to close the action.
Test understanding and inspect the arrangement
Use competent task planning, controlled isolation and evidence-based handback.
Ask the team what they would do if the control failed. Compare their answer with the actual arrangements and the source teaching. Check both what people understand and whether the physical control works.
Keep learning and operational authority clear
Independent warehouse awareness and decision practice for a GB baseline; check corresponding Northern Ireland duties and site arrangements. Completion is not practical competence, a licence or authority for specialist work.
The workbook is a practice document. Use the authorised workplace system for real risk assessments, permits, defect reports and audits. Video demonstrations can be added later; no missing video is required to complete this course.
Applied case
You are asked to prepare a toolbox talk and a check for the next shift. The current document says only: be more careful.
Compare your decision
Identify the task, responsible role, required evidence, restriction and trigger for review.
A useful action connects the work to its owner, evidence and a clear decision boundary.