Racking, pallets and high-bay storage

Free online training · Approximate learning time: 220–330 minutes · Self-paced

Full public teaching and readers are free without an account. A free learner account is required for saved LMS progress and recorded assessment. Completion and any course-completion certificate depend on the configured LMS conditions. Open the course overview.

Lesson 1

Storage is an engineered arrangement

Recognise rack damage, unsuitable loads, overhangs and unsafe access.

Storage is an engineered arrangement

A rack is a system of components, connections, floor support and loading arrangements. Beam changes, impacts and unsuitable pallets can affect that system. Do not infer capacity from the appearance of a neighbouring bay.

Connect storage design, condition, loading and access.

Follow the task through the area

A damaged rack upright

An upright has a fresh impact mark and the affected bay is still being replenished.

A damaged pallet above the aisle

A split pallet and overhanging cartons are visible on an upper beam.

A picker climbs the racking

A needed item is above reach and a worker proposes climbing the rack.

People beneath a suspended load

A non-routine lift is being discussed while pedestrians pass through its proposed path.

A heavier product in a changed storage bay

A new product and altered beam arrangement have been introduced without confirming the storage system design.

Loose stock above a picking position

A loose carton protrudes from an upper storage location. Picking continues underneath while replenishment is being planned.

A shelf has been altered without a capacity check

A beam has been moved and a board added to create another picking shelf. Stock is ready to go on it, but no one can confirm the revised capacity or approval.

A block stack is leaning into the aisle

Palletised cartons have been stacked on packs that are visibly crushing. The stack leans towards the aisle, and there is no confirmed limit for this product and packaging.

A picking aisle loses its lighting

An aisle light fails during the late shift. Stock shadows hide part of the floor and a pedestrian crossing, but the picking queue continues.

Challenge the first impression

Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

How do maintenance, inspection and testing differ?

Maintenance keeps equipment in safe condition; inspection finds dangerous condition or deterioration; testing challenges a specified function. Statutory thorough examination or written-scheme examination applies only to equipment within the relevant specialist regime.

Best-practice guide · six simple steps

Best-practice guide: Maintenance, inspection and testing of work equipment and machinery

Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.

Step 1 of 6 · StartThis cardPNG imagePDFView full sizeAll 6 cardsPNG images (ZIP)PDF (6 pages)

Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.

Read all six steps as text
  1. 1. How do maintenance, inspection and testing differ?

    Maintenance keeps equipment in safe condition; inspection finds dangerous condition or deterioration; testing challenges a specified function.

    • Avoid / redesign: At purchase or modification, the engineer moves lubrication, adjustment or condition-monitoring points outside the danger zone where practicable, so routine checks do not require guard removal or access beside moving parts.
    • Control the task: For the repair, authorised staff identify and isolate the conveyor and connected feeds, prevent reconnection, control stored energy and support parts that could move or fall using the machine-specific method.
    • Verify before release: Verify the revised arrangement against all use and maintenance tasks.

    Maintenance keeps equipment in safe condition; inspection finds dangerous condition or deterioration; testing challenges a specified function. Statutory thorough examination or written-scheme examination applies only to equipment within the relevant specialist regime. Maintenance keeps equipment in safe condition, inspection finds defects or deterioration, and testing checks a specified function.

    Apply it: Which part of this plan would you check at the workface before authorising the task?

    Read this part of the full topicOpen the full topicHSE inspection of work equipment (Great Britain)HSE maintenance of work equipment (Great Britain)HSE LOLER overview (Great Britain)
  2. 2. Turn maintenance, inspection and testing of work equipment and machinery knowledge into a decision

    Use the evidence to improve the actual work arrangement.

    • Change at source: At purchase or modification, the engineer moves lubrication, adjustment or condition-monitoring points outside the danger zone where practicable, so routine checks do not require guard removal or access beside moving parts.
    • Make it observable: Verify the revised arrangement against all use and maintenance tasks.
    • Keep useful evidence: Keep defect and hold record, isolation method, repair, functional test, affected inspection decision, contractor handback and recurring-failure review.

    Maintenance keeps equipment in safe condition, inspection finds defects or deterioration, and testing checks a specified function. Choose each check for the actual equipment and hazard; statutory examination is a separate requirement only where the relevant law applies. Keep defect and hold record, isolation method, repair, functional test, affected inspection decision, contractor handback and recurring-failure review.

    Apply it: What evidence would show that the change improves this task, rather than only completing a record?

    Read this part of the full topicOpen the full topicHSE managing risk using PPE (Great Britain; apply separate Northern Ireland law where relevant, Great Britain)HSE maintenance of work equipment (Great Britain)HSE inspection of work equipment (Great Britain)
  3. 3. the site team service and failed interlock

    Fictional example: a practical application of the existing topic lesson.

    • Setting: the site team’s warehouse conveyor moves bagged building material.
    • Act: The operator stops and reports the failure; the supervisor holds the whole affected line.
    • Hold / review: Hold if guard function, isolation, run-down, linked restart or personnel accounting is uncertain.

    Competent repair investigates the interlock and service change. No production running or improvised powered test occurs while a person is exposed. Restore guards, clear tools and people, perform the specified protected stop/restart test, record the result and obtain named release.

    Apply it: At which point would you hold this example, and what evidence would allow it to proceed?

    Read this part of the full topicOpen the full topicHSE maintenance of work equipment (Great Britain)HSE inspection of work equipment (Great Britain)HSE L22 Safe use of work equipment (Great Britain; approved for use in NI via HSENI)
  4. 4. Why does the distinction matter?

    Connect the task, the route to the person and the control that can fail.

    • Source / exposure: If the wrong check is chosen, a defect can remain hidden until a person meets moving machinery, a load falls or stored pressure is released.
    • Possible consequence: A quarterly conveyor service might change a bearing but leave an interlock disconnected.
    • Control failure: A forklift service might overlook a lifting-chain defect requiring competent examination.

    If the wrong check is chosen, a defect can remain hidden until a person meets moving machinery, a load falls or stored pressure is released.

    Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?

    Read this part of the full topicOpen the full topicHSE inspection of work equipment (Great Britain)HSE thorough examination of lifting equipment (Great Britain)HSE pressure systems regulations overview (Great Britain)
  5. 5. Choose controls for maintenance, inspection and testing of work equipment and machinery

    Start with the stronger practicable options and verify their effect.

    • Eliminate: At purchase or modification, the engineer moves lubrication, adjustment or condition-monitoring points outside the danger zone where practicable, so routine checks do not require guard removal or access beside moving parts.
    • Reduce: The engineer evaluates an alternative bearing or maintainable assembly that reduces intervention frequency or permits servicing from a protected location, subject to the machine specification and change assessment.
    • Isolate: For the repair, authorised staff identify and isolate the conveyor and connected feeds, prevent reconnection, control stored energy and support parts that could move or fall using the machine-specific method.
    • Control: The engineer defines a protected functional test with the required response and acceptance criteria, and the supervisor keeps everyone out of the danger zone.
    • PPE: Select eye protection for particles and other task-specific protection where residual exposure remains.

    Eliminate: At purchase or modification, the engineer moves lubrication, adjustment or condition-monitoring points outside the danger zone where practicable, so routine checks do not require guard removal or access beside moving parts. Reduce: The engineer evaluates an alternative bearing or maintainable assembly that reduces intervention frequency or permits servicing from a protected location, subject to the machine specification and change assessment. Isolate: For the repair, authorised staff identify and isolate the conveyor and connected feeds, prevent reconnection, control stored energy and support parts that could move or fall using the machine-specific method. Control: The engineer defines a protected functional test with the required response and acceptance criteria, and the supervisor keeps everyone out of the danger zone. PPE: Select eye protection for particles and other task-specific protection where residual exposure remains. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.

    Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?

    Read this part of the full topicOpen the full topicHSE managing risk using PPE (Great Britain; apply separate Northern Ireland law where relevant, Great Britain)HSE maintenance of work equipment (Great Britain)HSE inspection of work equipment (Great Britain)
  6. 6. Use the full maintenance, inspection and testing of work equipment and machinery lesson

    Follow the official sources below and retain the task-specific evidence.

    • Official guidance: HSE inspection of work equipment
    • Official guidance: HSE maintenance of work equipment
    • Task decision: Keep defect and hold record, isolation method, repair, functional test, affected inspection decision, contractor handback and recurring-failure review.

    Apply it: Which official source and full-topic section will you use to resolve the next decision?

    Read this part of the full topicOpen the full topicHSE inspection of work equipment (Great Britain)HSE maintenance of work equipment (Great Britain)HSE LOLER overview (Great Britain)

Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.

The Provision and Use of Work Equipment Regulations (PUWER), Lifting Operations and Lifting Equipment Regulations (LOLER) and Pressure Systems Safety Regulations (PSSR) each have distinct scope in GB and NI. A service sheet can show lubrication but not that an interlock stops a conveyor. A pre-use check can reveal an obvious damaged guard but does not replace a competent inspection where deterioration or installation creates significant risk. Lifting-equipment thorough examination and pressure-system written-scheme examination have different legal purposes and qualified examiners. HSE maintenance of work equipment, HSE inspection of work equipment, HSE LOLER overview and HSE pressure systems regulations overview.

Different checks and what they prove
Activity Purpose What it does not prove
Pre-use check User notices obvious damage or unsafe condition before use. A simple visual check does not prove hidden safety functions; an instructed pre-use routine may include safe protected functional checks within the user’s competence.
Maintenance Keeps or restores equipment to specification. A completed service alone is not an independent condition inspection.
PUWER inspection Competent check for installation or deterioration risk when triggered. Not an automatic statutory thorough examination of every machine.
Functional test Demonstrates a named guard, stop, brake, alarm or trip response. A partial test does not validate an entire system.
LOLER thorough examination Competent systematic examination of lifting equipment where applicable. Does not replace routine maintenance or all PUWER checks.
PSSR written-scheme examination Competent examination under a scheme for qualifying pressure systems. Not the same as a generic service or LOLER report.

Applied case

A damaged upright has been marked with tape. A heavy pallet is waiting below a changed beam position, while a picker considers climbing the rack to reach an overhang.

Compare your decision

A rack is a system of components, connections, floor support and loading arrangements. Beam changes, impacts and unsuitable pallets can affect that system. Do not infer capacity from the appearance of a neighbouring bay.

A rack is a system of components, connections, floor support and loading arrangements. Beam changes, impacts and unsuitable pallets can affect that system. Do not infer capacity from the appearance of a neighbouring bay. Check the actual conditions and retain protection while gaps are resolved.

Lesson 2

Read load, support and access together

Use the approved storage arrangement and capacity information for the actual configuration.

Read load, support and access together

A stable-looking load may still overhang, be poorly supported or exceed the approved arrangement. Examine how it will be placed and retrieved, who is exposed below it and whether access can be made safely without climbing the rack.

Connect storage design, condition, loading and access.

Follow the task through the area

A damaged rack upright

An upright has a fresh impact mark and the affected bay is still being replenished.

A damaged pallet above the aisle

A split pallet and overhanging cartons are visible on an upper beam.

A picker climbs the racking

A needed item is above reach and a worker proposes climbing the rack.

People beneath a suspended load

A non-routine lift is being discussed while pedestrians pass through its proposed path.

A heavier product in a changed storage bay

A new product and altered beam arrangement have been introduced without confirming the storage system design.

Loose stock above a picking position

A loose carton protrudes from an upper storage location. Picking continues underneath while replenishment is being planned.

A shelf has been altered without a capacity check

A beam has been moved and a board added to create another picking shelf. Stock is ready to go on it, but no one can confirm the revised capacity or approval.

A block stack is leaning into the aisle

Palletised cartons have been stacked on packs that are visibly crushing. The stack leans towards the aisle, and there is no confirmed limit for this product and packaging.

A picking aisle loses its lighting

An aisle light fails during the late shift. Stock shadows hide part of the floor and a pedestrian crossing, but the picking queue continues.

Challenge the first impression

Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

What does load-handling equipment and lifting operations mean?

It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system.

Best-practice guide · six simple steps

Best-practice guide: Load-Handling Equipment and Lifting Operations

Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.

Step 1 of 6 · StartThis cardPNG imagePDFView full sizeAll 6 cardsPNG images (ZIP)PDF (6 pages)

Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.

Read all six steps as text
  1. 1. What does load-handling equipment and lifting operations mean?

    It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system.

    • Avoid / redesign: Avoid moving the motor by redesigning work at its current position where feasible.
    • Control the task: Use rated lifting gear, secure attachments and a segregated travel route.
    • Verify before release: Planner records feasibility; unclear task holds lift.

    It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system. Choose a safer way to move the load before designing a lift.

    Apply it: Which part of this plan would you check at the workface before authorising the task?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)
  2. 2. Turn load-handling equipment and lifting operations knowledge into a decision

    Use the evidence to improve the actual work arrangement.

    • Change at source: Avoid moving the motor by redesigning work at its current position where feasible.
    • Make it observable: Planner records feasibility; unclear task holds lift.
    • Keep useful evidence: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Choose a safer way to move the load before designing a lift. Where lifting equipment is needed, a competent person plans the operation, selects equipment and accessories for the load and environment, keeps people away from a suspended load and verifies pre-use checks, maintenance and statutory examination. Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Apply it: What evidence would show that the change improves this task, rather than only completing a record?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  3. 3. Worked lifting assessment example

    Fictional example: a practical application of the existing topic lesson.

    • Load: What is being lifted and where is the centre of gravity?
    • Equipment: Is the lift truck and attachment suitable?
    • Route: Can the load travel safely?

    Load: What is being lifted and where is the centre of gravity? Evidence / response: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet. Equipment: Is the lift truck and attachment suitable? Evidence / response: Correct rated capacity, fork length suitable, daily check complete.

    Apply it: At which point would you hold this example, and what evidence would allow it to proceed?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  4. 4. Follow the load and the people in its path

    Connect the task, the route to the person and the control that can fail.

    • Load failure: An unsuitable attachment or insecure load can fall or shift.
    • Movement: A swinging load or moving lifting equipment can trap or strike people.
    • Stability: Ground, capacity or setup failures can overturn equipment or destabilise the lift.

    An unsuitable attachment or insecure load can fall or shift. A swinging load or moving lifting equipment can trap or strike people. Ground, capacity or setup failures can overturn equipment or destabilise the lift. Use the full topic for the detailed mechanism, task limits and source scope.

    Apply it: Where is this harm route present in the actual work, and which control breaks it before anyone is exposed?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)
  5. 5. Choose controls for load-handling equipment and lifting operations

    Start with the stronger practicable options and verify their effect.

    • Eliminate: Avoid moving the motor by redesigning work at its current position where feasible.
    • Reduce: Use a lighter modular component or a lower-risk delivery/move method.
    • Isolate: Use rated lifting gear, secure attachments and a segregated travel route.
    • Control: Approved lift plan, signaler, exclusion, weather/ground checks and communication.
    • PPE: Head, foot, hand protection for residual contact hazard.

    Eliminate: Avoid moving the motor by redesigning work at its current position where feasible. Reduce: Use a lighter modular component or a lower-risk delivery/move method. Isolate: Use rated lifting gear, secure attachments and a segregated travel route. Control: Approved lift plan, signaler, exclusion, weather/ground checks and communication. PPE: Head, foot, hand protection for residual contact hazard. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.

    Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  6. 6. Use the full load-handling equipment and lifting operations lesson

    Follow the official sources below and retain the task-specific evidence.

    • Official guidance: LOLER overview
    • Official guidance: Safe use of lifting equipment (L113)
    • Task decision: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Apply it: Which official source and full-topic section will you use to resolve the next decision?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)

Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.

This topic sits between manual handling, work equipment, workplace transport and lifting operations. A sack truck, trolley or pallet truck may reduce manual handling effort, but it can introduce new risks such as runaway loads, poor steering, trapping, slopes, unsuitable wheels or overloading. A crane, hoist, lift truck or lifting accessory can remove manual effort but creates higher-energy hazards such as suspended loads, overturning, dropped loads, crushing, striking structures or instability.

The first professional judgement is whether the load needs to be handled at all. Can the task be eliminated, delivered closer to the point of use, split into smaller units, palletised, mechanised, redesigned or completed at a better height? If handling remains, the task, individual, load and environment still matter. If lifting equipment is used, the organisation must also consider suitability, strength, stability, marking, pre-use checks, maintenance, inspection, thorough examination, competent planning and supervision.

For learners, the key is not to memorise equipment names. The useful mental model is: what is the load, how will it move, what could fail, who could be struck, trapped, fall or strain, what prevents the event, and what evidence proves the control is live today?

Lifting Operations and Lifting Equipment Regulations (LOLER) scope depends on what the equipment actually does. HSE’s LOLER overview says simple pallet trucks that raise a load only just clear of the ground, and many conveyors, are outside LOLER but remain subject to the Provision and Use of Work Equipment Regulations (PUWER). HSE L113 identifies high-lift pallet trucks able to raise forks above 300 mm as LOLER examples. Do not assign the LOLER six-/12-month examination cycle to every load-handling aid; first check whether it is lifting equipment within scope.

Equipment or activityWhat it is used forMain risk questions
Sack trucks and trolleysMoving smaller loads over short distances.Is the load stable, route suitable, slope controlled and pushing/pulling force reasonable?
Pallet trucksMoving palletised loads on suitable floors.Is the pallet sound, floor level, load within capacity and pedestrian route controlled?
People-handling aidsReducing manual effort in health and social care or assisted movement.Is the aid suitable for the person, maintained and used by trained workers?
Fork-lift trucksLifting and transporting palletised or compatible loads.Is the operator trained, load secure, route segregated and attachment suitable?
Hoists and lifting accessoriesRaising, lowering or positioning loads.Is the safe working load / working load limit marked, accessory compatible and pre-use check complete?
ConveyorsMoving loads continuously through a process.Are trapping points guarded, emergency stops working and maintenance isolated?
Cranes and complex liftsMoving heavier, unusual or high-risk loads.Is there a competent lifting plan, appointed person, exclusion zone and ground/load assessment?

Applied case

A damaged upright has been marked with tape. A heavy pallet is waiting below a changed beam position, while a picker considers climbing the rack to reach an overhang.

Compare your decision

A stable-looking load may still overhang, be poorly supported or exceed the approved arrangement. Examine how it will be placed and retrieved, who is exposed below it and whether access can be made safely without climbing the rack.

A stable-looking load may still overhang, be poorly supported or exceed the approved arrangement. Examine how it will be placed and retrieved, who is exposed below it and whether access can be made safely without climbing the rack. Check the actual conditions and retain protection while gaps are resolved.

Lesson 3

A damaged rack upright

Keep people and replenishment clear of the affected area and report for competent rack assessment and a safe response.

Read the scene evidence

An upright has a fresh impact mark and the affected bay is still being replenished.

Identify the condition separately from the exposed person and any possible outcome.

How the harm pathway develops

Damaged load-bearing storage equipment

An upright has a fresh impact mark and the affected bay is still being replenished.

How people can be exposed

People or stock remain beneath a storage system whose condition is uncertain.

Possible harm

Falling loads or a partial storage-system collapse.

Compare the work arrangements

ArrangementWhat changes exposure?
Uncontrolled arrangementAn upright has a fresh impact mark and the affected bay is still being replenished. The condition remains unresolved.
Protective responseKeep people and replenishment clear of the affected area and report for competent rack assessment and a safe response.

Select controls by how they prevent harm

Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.

Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.

Control levelApplication to this case
EliminationRemove the recurring vehicle conflict through a redesigned storage and access layout.
SubstitutionCompare a storage method better suited to the products and handling equipment.
Engineering controlsProvide suitable impact protection and correctly designed storage equipment.
Administrative controlsReport damage promptly, control affected use and inspect through competent arrangements.
PPEUse assessed head and foot protection for residual risks; it does not restore rack capacity.

Verify, communicate and hand back

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.

How do maintenance, inspection and testing differ?

Maintenance keeps equipment in safe condition; inspection finds dangerous condition or deterioration; testing challenges a specified function. Statutory thorough examination or written-scheme examination applies only to equipment within the relevant specialist regime.

Best-practice guide · six simple steps

Best-practice guide: Maintenance, inspection and testing of work equipment and machinery

Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.

Step 1 of 6 · StartThis cardPNG imagePDFView full sizeAll 6 cardsPNG images (ZIP)PDF (6 pages)

Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.

Read all six steps as text
  1. 1. How do maintenance, inspection and testing differ?

    Maintenance keeps equipment in safe condition; inspection finds dangerous condition or deterioration; testing challenges a specified function.

    • Avoid / redesign: At purchase or modification, the engineer moves lubrication, adjustment or condition-monitoring points outside the danger zone where practicable, so routine checks do not require guard removal or access beside moving parts.
    • Control the task: For the repair, authorised staff identify and isolate the conveyor and connected feeds, prevent reconnection, control stored energy and support parts that could move or fall using the machine-specific method.
    • Verify before release: Verify the revised arrangement against all use and maintenance tasks.

    Maintenance keeps equipment in safe condition; inspection finds dangerous condition or deterioration; testing challenges a specified function. Statutory thorough examination or written-scheme examination applies only to equipment within the relevant specialist regime. Maintenance keeps equipment in safe condition, inspection finds defects or deterioration, and testing checks a specified function.

    Apply it: Which part of this plan would you check at the workface before authorising the task?

    Read this part of the full topicOpen the full topicHSE inspection of work equipment (Great Britain)HSE maintenance of work equipment (Great Britain)HSE LOLER overview (Great Britain)
  2. 2. Turn maintenance, inspection and testing of work equipment and machinery knowledge into a decision

    Use the evidence to improve the actual work arrangement.

    • Change at source: At purchase or modification, the engineer moves lubrication, adjustment or condition-monitoring points outside the danger zone where practicable, so routine checks do not require guard removal or access beside moving parts.
    • Make it observable: Verify the revised arrangement against all use and maintenance tasks.
    • Keep useful evidence: Keep defect and hold record, isolation method, repair, functional test, affected inspection decision, contractor handback and recurring-failure review.

    Maintenance keeps equipment in safe condition, inspection finds defects or deterioration, and testing checks a specified function. Choose each check for the actual equipment and hazard; statutory examination is a separate requirement only where the relevant law applies. Keep defect and hold record, isolation method, repair, functional test, affected inspection decision, contractor handback and recurring-failure review.

    Apply it: What evidence would show that the change improves this task, rather than only completing a record?

    Read this part of the full topicOpen the full topicHSE managing risk using PPE (Great Britain; apply separate Northern Ireland law where relevant, Great Britain)HSE maintenance of work equipment (Great Britain)HSE inspection of work equipment (Great Britain)
  3. 3. the site team service and failed interlock

    Fictional example: a practical application of the existing topic lesson.

    • Setting: the site team’s warehouse conveyor moves bagged building material.
    • Act: The operator stops and reports the failure; the supervisor holds the whole affected line.
    • Hold / review: Hold if guard function, isolation, run-down, linked restart or personnel accounting is uncertain.

    Competent repair investigates the interlock and service change. No production running or improvised powered test occurs while a person is exposed. Restore guards, clear tools and people, perform the specified protected stop/restart test, record the result and obtain named release.

    Apply it: At which point would you hold this example, and what evidence would allow it to proceed?

    Read this part of the full topicOpen the full topicHSE maintenance of work equipment (Great Britain)HSE inspection of work equipment (Great Britain)HSE L22 Safe use of work equipment (Great Britain; approved for use in NI via HSENI)
  4. 4. Why does the distinction matter?

    Connect the task, the route to the person and the control that can fail.

    • Source / exposure: If the wrong check is chosen, a defect can remain hidden until a person meets moving machinery, a load falls or stored pressure is released.
    • Possible consequence: A quarterly conveyor service might change a bearing but leave an interlock disconnected.
    • Control failure: A forklift service might overlook a lifting-chain defect requiring competent examination.

    If the wrong check is chosen, a defect can remain hidden until a person meets moving machinery, a load falls or stored pressure is released.

    Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?

    Read this part of the full topicOpen the full topicHSE inspection of work equipment (Great Britain)HSE thorough examination of lifting equipment (Great Britain)HSE pressure systems regulations overview (Great Britain)
  5. 5. Choose controls for maintenance, inspection and testing of work equipment and machinery

    Start with the stronger practicable options and verify their effect.

    • Eliminate: At purchase or modification, the engineer moves lubrication, adjustment or condition-monitoring points outside the danger zone where practicable, so routine checks do not require guard removal or access beside moving parts.
    • Reduce: The engineer evaluates an alternative bearing or maintainable assembly that reduces intervention frequency or permits servicing from a protected location, subject to the machine specification and change assessment.
    • Isolate: For the repair, authorised staff identify and isolate the conveyor and connected feeds, prevent reconnection, control stored energy and support parts that could move or fall using the machine-specific method.
    • Control: The engineer defines a protected functional test with the required response and acceptance criteria, and the supervisor keeps everyone out of the danger zone.
    • PPE: Select eye protection for particles and other task-specific protection where residual exposure remains.

    Eliminate: At purchase or modification, the engineer moves lubrication, adjustment or condition-monitoring points outside the danger zone where practicable, so routine checks do not require guard removal or access beside moving parts. Reduce: The engineer evaluates an alternative bearing or maintainable assembly that reduces intervention frequency or permits servicing from a protected location, subject to the machine specification and change assessment. Isolate: For the repair, authorised staff identify and isolate the conveyor and connected feeds, prevent reconnection, control stored energy and support parts that could move or fall using the machine-specific method. Control: The engineer defines a protected functional test with the required response and acceptance criteria, and the supervisor keeps everyone out of the danger zone. PPE: Select eye protection for particles and other task-specific protection where residual exposure remains. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.

    Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?

    Read this part of the full topicOpen the full topicHSE managing risk using PPE (Great Britain; apply separate Northern Ireland law where relevant, Great Britain)HSE maintenance of work equipment (Great Britain)HSE inspection of work equipment (Great Britain)
  6. 6. Use the full maintenance, inspection and testing of work equipment and machinery lesson

    Follow the official sources below and retain the task-specific evidence.

    • Official guidance: HSE inspection of work equipment
    • Official guidance: HSE maintenance of work equipment
    • Task decision: Keep defect and hold record, isolation method, repair, functional test, affected inspection decision, contractor handback and recurring-failure review.

    Apply it: Which official source and full-topic section will you use to resolve the next decision?

    Read this part of the full topicOpen the full topicHSE inspection of work equipment (Great Britain)HSE maintenance of work equipment (Great Britain)HSE LOLER overview (Great Britain)

Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.

The Provision and Use of Work Equipment Regulations (PUWER), Lifting Operations and Lifting Equipment Regulations (LOLER) and Pressure Systems Safety Regulations (PSSR) each have distinct scope in GB and NI. A service sheet can show lubrication but not that an interlock stops a conveyor. A pre-use check can reveal an obvious damaged guard but does not replace a competent inspection where deterioration or installation creates significant risk. Lifting-equipment thorough examination and pressure-system written-scheme examination have different legal purposes and qualified examiners. HSE maintenance of work equipment, HSE inspection of work equipment, HSE LOLER overview and HSE pressure systems regulations overview.

Different checks and what they prove
Activity Purpose What it does not prove
Pre-use check User notices obvious damage or unsafe condition before use. A simple visual check does not prove hidden safety functions; an instructed pre-use routine may include safe protected functional checks within the user’s competence.
Maintenance Keeps or restores equipment to specification. A completed service alone is not an independent condition inspection.
PUWER inspection Competent check for installation or deterioration risk when triggered. Not an automatic statutory thorough examination of every machine.
Functional test Demonstrates a named guard, stop, brake, alarm or trip response. A partial test does not validate an entire system.
LOLER thorough examination Competent systematic examination of lifting equipment where applicable. Does not replace routine maintenance or all PUWER checks.
PSSR written-scheme examination Competent examination under a scheme for qualifying pressure systems. Not the same as a generic service or LOLER report.

How can the ISO 45001 hierarchy of controls reduce machinery risks during maintenance, inspection and testing?

Choose the safe intervention and test method before a maintainer approaches danger. Design out unnecessary access, use engineered separation and secure isolation for the planned work, then support those measures with competent instruction, controlled tests and residual PPE.

Illustrative decision: BuildOut replaces a conveyor bearing and checks the protective interlock. Mechanical repair and demonstration of the safety function are separate tasks. The engineer specifies the isolation and the protected test; the supervisor coordinates operators, cleaners and linked equipment.

ERICPD means Eliminate, Reduce (including substitution), Isolate, Control, PPE and Discipline. The five-level hierarchy groups measures as elimination, substitution, engineering controls, administrative controls and PPE. They overlap: isolation is usually an engineering measure; control can include engineered and administrative measures. Discipline means maintaining and checking the controls, supervising the method and learning from defects, rather than blaming someone or accepting weaker protection.

How can the ERICPD hierarchy of controls reduce machinery risks during maintenance, inspection and testing?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Controls and evidence for the illustrative task
ERICPD and five-level positionIntervention and ownerVerification, failure and stop point
Eliminate / eliminationAt purchase or modification, the engineer moves lubrication, adjustment or condition-monitoring points outside the danger zone where practicable, so routine checks do not require guard removal or access beside moving parts.Verify the revised arrangement against all use and maintenance tasks. An awkward new access route or exposed linked drive means the intended risk reduction has not been demonstrated.
Reduce / substitution when replacing a hazard; otherwise engineering or administrative risk reductionThe engineer evaluates an alternative bearing or maintainable assembly that reduces intervention frequency or permits servicing from a protected location, subject to the machine specification and change assessment.Confirm compatibility, load, speed and protective-function effects with suitable technical information. A component substitution must not be assumed equivalent because it fits.
Isolate / engineeringFor the repair, authorised staff identify and isolate the conveyor and connected feeds, prevent reconnection, control stored energy and support parts that could move or fall using the machine-specific method.Verify the safe state before access. Unknown energy, a remaining live feed, pressure or an unstable part holds the repair; an emergency stop alone does not establish isolation.
Control / engineered and administrative measuresThe engineer defines a protected functional test with the required response and acceptance criteria, and the supervisor keeps everyone out of the danger zone. A necessary powered test uses a separately assessed specialist method.Record results and restore the safeguards and authorised operating mode. Failed stopping or restart behaviour, an exposed person or an unplanned powered test prevents hand-back.
PPE / PPESelect eye protection for particles and other task-specific protection where residual exposure remains. Consider entanglement and compatibility before selecting gloves around rotation; the repair method must control contact with movement.Inspect PPE and follow its maintenance and replacement arrangements. PPE cannot validate an interlock, hold a falling part or make an exposed conveyor safe.
Discipline / sustained engineering and administrative controlsManagers resource the inspection plan; supervisors enforce defect quarantine and named release; competent staff review recurring failures and changes to intervals or methods.Keep the defect, repair, protected test and hand-back evidence. A service receipt is not proof that each safety function works, and inspection intervals remain equipment- and risk-specific.

How can the ISO 45001 hierarchy of controls reduce machinery risks during maintenance, inspection and testing?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Controls and evidence for the illustrative task
ERICPD and five-level positionIntervention and ownerVerification, failure and stop point
Eliminate / eliminationAt purchase or modification, the engineer moves lubrication, adjustment or condition-monitoring points outside the danger zone where practicable, so routine checks do not require guard removal or access beside moving parts.Verify the revised arrangement against all use and maintenance tasks. An awkward new access route or exposed linked drive means the intended risk reduction has not been demonstrated.
Reduce / substitution when replacing a hazard; otherwise engineering or administrative risk reductionThe engineer evaluates an alternative bearing or maintainable assembly that reduces intervention frequency or permits servicing from a protected location, subject to the machine specification and change assessment.Confirm compatibility, load, speed and protective-function effects with suitable technical information. A component substitution must not be assumed equivalent because it fits.
Isolate / engineeringFor the repair, authorised staff identify and isolate the conveyor and connected feeds, prevent reconnection, control stored energy and support parts that could move or fall using the machine-specific method.Verify the safe state before access. Unknown energy, a remaining live feed, pressure or an unstable part holds the repair; an emergency stop alone does not establish isolation.
Control / engineered and administrative measuresThe engineer defines a protected functional test with the required response and acceptance criteria, and the supervisor keeps everyone out of the danger zone. A necessary powered test uses a separately assessed specialist method.Record results and restore the safeguards and authorised operating mode. Failed stopping or restart behaviour, an exposed person or an unplanned powered test prevents hand-back.
PPE / PPESelect eye protection for particles and other task-specific protection where residual exposure remains. Consider entanglement and compatibility before selecting gloves around rotation; the repair method must control contact with movement.Inspect PPE and follow its maintenance and replacement arrangements. PPE cannot validate an interlock, hold a falling part or make an exposed conveyor safe.
Discipline / sustained engineering and administrative controlsManagers resource the inspection plan; supervisors enforce defect quarantine and named release; competent staff review recurring failures and changes to intervals or methods.Keep the defect, repair, protected test and hand-back evidence. A service receipt is not proof that each safety function works, and inspection intervals remain equipment- and risk-specific.

The comparison is an original illustrative application of the general HSE hierarchy, not a machine-specific method, permit or design approval. The employer must choose measures for the actual work and jurisdiction. Apply the separate Northern Ireland legal route where relevant; the local assessment and competent technical decision govern release.

Sources: HSE hierarchy of controls; HSE maintenance of work equipment; HSE inspection of work equipment; HSENI PUWER 1999.

Applied case

An upright has a fresh impact mark and the affected bay is still being replenished. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.

Compare your decision

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.

Lesson 4

A damaged pallet above the aisle

Keep people clear below and arrange a competent, planned recovery using suitable equipment.

Read the scene evidence

A split pallet and overhanging cartons are visible on an upper beam.

Identify the condition separately from the exposed person and any possible outcome.

How the harm pathway develops

An unstable or unsuitable palletised load at height

A split pallet and overhanging cartons are visible on an upper beam.

How people can be exposed

People pass or equipment contacts the unstable load.

Possible harm

Falling objects or loss of load stability.

Compare the work arrangements

ArrangementWhat changes exposure?
Uncontrolled arrangementA split pallet and overhanging cartons are visible on an upper beam. The condition remains unresolved.
Protective responseKeep people clear below and arrange a competent, planned recovery using suitable equipment.

Select controls by how they prevent harm

Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.

Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.

Control levelApplication to this case
EliminationPrevent unsuitable load units entering high-level storage.
SubstitutionChoose suitable pallets and packaging for the actual product and storage system.
Engineering controlsProvide suitable load support and storage equipment within its design capacity.
Administrative controlsVerify load condition, weight, beam configuration and replenishment checks.
PPEProvide suitable residual head and foot protection; never rely on it below an unstable load.

Verify, communicate and hand back

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.

What does load-handling equipment and lifting operations mean?

It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system.

Best-practice guide · six simple steps

Best-practice guide: Load-Handling Equipment and Lifting Operations

Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.

Step 1 of 6 · StartThis cardPNG imagePDFView full sizeAll 6 cardsPNG images (ZIP)PDF (6 pages)

Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.

Read all six steps as text
  1. 1. What does load-handling equipment and lifting operations mean?

    It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system.

    • Avoid / redesign: Avoid moving the motor by redesigning work at its current position where feasible.
    • Control the task: Use rated lifting gear, secure attachments and a segregated travel route.
    • Verify before release: Planner records feasibility; unclear task holds lift.

    It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system. Choose a safer way to move the load before designing a lift.

    Apply it: Which part of this plan would you check at the workface before authorising the task?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)
  2. 2. Turn load-handling equipment and lifting operations knowledge into a decision

    Use the evidence to improve the actual work arrangement.

    • Change at source: Avoid moving the motor by redesigning work at its current position where feasible.
    • Make it observable: Planner records feasibility; unclear task holds lift.
    • Keep useful evidence: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Choose a safer way to move the load before designing a lift. Where lifting equipment is needed, a competent person plans the operation, selects equipment and accessories for the load and environment, keeps people away from a suspended load and verifies pre-use checks, maintenance and statutory examination. Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Apply it: What evidence would show that the change improves this task, rather than only completing a record?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  3. 3. Worked lifting assessment example

    Fictional example: a practical application of the existing topic lesson.

    • Load: What is being lifted and where is the centre of gravity?
    • Equipment: Is the lift truck and attachment suitable?
    • Route: Can the load travel safely?

    Load: What is being lifted and where is the centre of gravity? Evidence / response: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet. Equipment: Is the lift truck and attachment suitable? Evidence / response: Correct rated capacity, fork length suitable, daily check complete.

    Apply it: At which point would you hold this example, and what evidence would allow it to proceed?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  4. 4. Follow the load and the people in its path

    Connect the task, the route to the person and the control that can fail.

    • Load failure: An unsuitable attachment or insecure load can fall or shift.
    • Movement: A swinging load or moving lifting equipment can trap or strike people.
    • Stability: Ground, capacity or setup failures can overturn equipment or destabilise the lift.

    An unsuitable attachment or insecure load can fall or shift. A swinging load or moving lifting equipment can trap or strike people. Ground, capacity or setup failures can overturn equipment or destabilise the lift. Use the full topic for the detailed mechanism, task limits and source scope.

    Apply it: Where is this harm route present in the actual work, and which control breaks it before anyone is exposed?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)
  5. 5. Choose controls for load-handling equipment and lifting operations

    Start with the stronger practicable options and verify their effect.

    • Eliminate: Avoid moving the motor by redesigning work at its current position where feasible.
    • Reduce: Use a lighter modular component or a lower-risk delivery/move method.
    • Isolate: Use rated lifting gear, secure attachments and a segregated travel route.
    • Control: Approved lift plan, signaler, exclusion, weather/ground checks and communication.
    • PPE: Head, foot, hand protection for residual contact hazard.

    Eliminate: Avoid moving the motor by redesigning work at its current position where feasible. Reduce: Use a lighter modular component or a lower-risk delivery/move method. Isolate: Use rated lifting gear, secure attachments and a segregated travel route. Control: Approved lift plan, signaler, exclusion, weather/ground checks and communication. PPE: Head, foot, hand protection for residual contact hazard. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.

    Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  6. 6. Use the full load-handling equipment and lifting operations lesson

    Follow the official sources below and retain the task-specific evidence.

    • Official guidance: LOLER overview
    • Official guidance: Safe use of lifting equipment (L113)
    • Task decision: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Apply it: Which official source and full-topic section will you use to resolve the next decision?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)

Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.

This topic sits between manual handling, work equipment, workplace transport and lifting operations. A sack truck, trolley or pallet truck may reduce manual handling effort, but it can introduce new risks such as runaway loads, poor steering, trapping, slopes, unsuitable wheels or overloading. A crane, hoist, lift truck or lifting accessory can remove manual effort but creates higher-energy hazards such as suspended loads, overturning, dropped loads, crushing, striking structures or instability.

The first professional judgement is whether the load needs to be handled at all. Can the task be eliminated, delivered closer to the point of use, split into smaller units, palletised, mechanised, redesigned or completed at a better height? If handling remains, the task, individual, load and environment still matter. If lifting equipment is used, the organisation must also consider suitability, strength, stability, marking, pre-use checks, maintenance, inspection, thorough examination, competent planning and supervision.

For learners, the key is not to memorise equipment names. The useful mental model is: what is the load, how will it move, what could fail, who could be struck, trapped, fall or strain, what prevents the event, and what evidence proves the control is live today?

Lifting Operations and Lifting Equipment Regulations (LOLER) scope depends on what the equipment actually does. HSE’s LOLER overview says simple pallet trucks that raise a load only just clear of the ground, and many conveyors, are outside LOLER but remain subject to the Provision and Use of Work Equipment Regulations (PUWER). HSE L113 identifies high-lift pallet trucks able to raise forks above 300 mm as LOLER examples. Do not assign the LOLER six-/12-month examination cycle to every load-handling aid; first check whether it is lifting equipment within scope.

Equipment or activityWhat it is used forMain risk questions
Sack trucks and trolleysMoving smaller loads over short distances.Is the load stable, route suitable, slope controlled and pushing/pulling force reasonable?
Pallet trucksMoving palletised loads on suitable floors.Is the pallet sound, floor level, load within capacity and pedestrian route controlled?
People-handling aidsReducing manual effort in health and social care or assisted movement.Is the aid suitable for the person, maintained and used by trained workers?
Fork-lift trucksLifting and transporting palletised or compatible loads.Is the operator trained, load secure, route segregated and attachment suitable?
Hoists and lifting accessoriesRaising, lowering or positioning loads.Is the safe working load / working load limit marked, accessory compatible and pre-use check complete?
ConveyorsMoving loads continuously through a process.Are trapping points guarded, emergency stops working and maintenance isolated?
Cranes and complex liftsMoving heavier, unusual or high-risk loads.Is there a competent lifting plan, appointed person, exclusion zone and ground/load assessment?

How can the hierarchy of controls prevent dropped loads and unsafe lifting operations?

Remove the need for hazardous handling where feasible, then select equipment and controls for the residual lift.

Eliminate, Reduce, Isolate, Control, Personal protective equipment (PPE) and Discipline (ERICPD) below maps to the five-level hierarchy for a motor lifted from a workshop bay. HSE lifting overview sets the planning and equipment principles. The supervisor holds the move if load identity, attachment, travel clearance or equipment condition is uncertain.

The five levels are elimination, substitution, engineering, administrative controls and PPE. “Discipline” is the sustained inspection, feedback and repair that keeps each selected level effective.

How can the ERICPD hierarchy of controls prevent dropped loads and unsafe lifting operations?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Task application for Load-Handling Equipment and Lifting Operations
Activity and release context
Eliminate, Reduce, Isolate, Control, Personal protective equipment (PPE) and Discipline (ERICPD) below maps to the five-level hierarchy for a motor lifted from a workshop bay. HSE lifting overview sets the planning and equipment principles. The supervisor holds the move if load identity, attachment, travel clearance or equipment condition is uncertain.
Full example
Read the activity, checks and hand-back in context
ERICPDFive-level hierarchyMotor-move choiceOwner, proof and stop
EliminateEliminationAvoid moving the motor by redesigning work at its current position where feasible.Planner records feasibility; unclear task holds lift.
ReduceSubstitutionUse a lighter modular component or a lower-risk delivery/move method.Engineering verifies compatibility and mass.
Isolate / ControlEngineering controlsUse rated lifting gear, secure attachments and a segregated travel route.Lift supervisor checks setup; failed rating or attachment stops move.
ControlAdministrative controlsApproved lift plan, signaler, exclusion, weather/ground checks and communication.Supervisor briefs crew; change in route or load triggers hold.
PPEPPEHead, foot, hand protection for residual contact hazard.Selector checks suitability; PPE never justifies entry under load.
DisciplineSustaining all levelsRecord checks, defects, examination, repairs and near misses.Manager verifies hand-back and recurring defect review.

How can the ISO 45001 hierarchy of controls prevent dropped loads and unsafe lifting operations?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Task application for Load-Handling Equipment and Lifting Operations
Activity and release context
Eliminate, Reduce, Isolate, Control, Personal protective equipment (PPE) and Discipline (ERICPD) below maps to the five-level hierarchy for a motor lifted from a workshop bay. HSE lifting overview sets the planning and equipment principles. The supervisor holds the move if load identity, attachment, travel clearance or equipment condition is uncertain.
Full example
Read the activity, checks and hand-back in context
ERICPDFive-level hierarchyMotor-move choiceOwner, proof and stop
EliminateEliminationAvoid moving the motor by redesigning work at its current position where feasible.Planner records feasibility; unclear task holds lift.
ReduceSubstitutionUse a lighter modular component or a lower-risk delivery/move method.Engineering verifies compatibility and mass.
Isolate / ControlEngineering controlsUse rated lifting gear, secure attachments and a segregated travel route.Lift supervisor checks setup; failed rating or attachment stops move.
ControlAdministrative controlsApproved lift plan, signaler, exclusion, weather/ground checks and communication.Supervisor briefs crew; change in route or load triggers hold.
PPEPPEHead, foot, hand protection for residual contact hazard.Selector checks suitability; PPE never justifies entry under load.
DisciplineSustaining all levelsRecord checks, defects, examination, repairs and near misses.Manager verifies hand-back and recurring defect review.

Applied case

A split pallet and overhanging cartons are visible on an upper beam. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.

Compare your decision

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.

Lesson 5

A picker climbs the racking

Stop the climb from a safe position and arrange a suitable retrieval method with the responsible person.

Read the scene evidence

A needed item is above reach and a worker proposes climbing the rack.

Identify the condition separately from the exposed person and any possible outcome.

How the harm pathway develops

Unplanned access at height using storage equipment

A needed item is above reach and a worker proposes climbing the rack.

How people can be exposed

A worker climbs without a suitable working platform or safe access.

Possible harm

A fall or dislodged stock striking people below.

Compare the work arrangements

ArrangementWhat changes exposure?
Uncontrolled arrangementA needed item is above reach and a worker proposes climbing the rack. The condition remains unresolved.
Protective responseStop the climb from a safe position and arrange a suitable retrieval method with the responsible person.

Select controls by how they prevent harm

Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.

Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.

Control levelApplication to this case
EliminationKeep frequently needed stock accessible from ground level.
SubstitutionCompare a suitable ground-based retrieval method for the product.
Engineering controlsProvide properly selected protected access equipment where height cannot be avoided.
Administrative controlsPlan retrieval, authorisation, inspection and the area below the work.
PPEAny fall protection must follow a competent task and rescue plan; it is not permission to climb racks.

Verify, communicate and hand back

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.

What counts as work at height?

It is work in any place where a person could fall a distance liable to cause personal injury if precautions were absent; there is no universal two-metre trigger.

Best-practice guide · six simple steps

Best-practice guide: Working at Height

Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.

Step 1 of 6 · StartThis cardPNG imagePDFView full sizeAll 6 cardsPNG images (ZIP)PDF (6 pages)

Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.

Read all six steps as text
  1. 1. Avoid height, then prevent the remaining fall

    Use the actual task, structure and conditions to choose the method.

    • Avoid: Complete the task from ground level where reasonably practicable.
    • Prevent: Use a suitable safe place or collective fall prevention where work at height remains.
    • Minimise: Plan the distance, consequences and rescue for a remaining fall risk.

    Keep the work-at-height sequence: avoid the work where reasonably practicable, prevent falls, then minimise the distance and consequences of a remaining fall. Choose collective protection before personal protection at each level. A short task or a fall below two metres can still cause severe injury.

    Apply it: Can the task be completed without approaching a fragile surface, opening or unprotected edge?

    Read this part of the full topicOpen the full topicWork at Height Regulations 2005 (Great Britain law)Work at Height Regulations (Northern Ireland) 2005 (Northern Ireland law)HSE introduction to working at height safely (Great Britain regulator guidance)
  2. 2. Turn working at height knowledge into a decision

    Use the evidence to improve the actual work arrangement.

    • Change at source: Lower a lighting mast for servicing or inspect from a suitable ground-level method so the worker does not need to reach an edge or fragile surface.
    • Make it observable: Facilities or design owner verifies access, reach, electrical interfaces and the completed task.
    • Keep useful evidence: Survey, method choice, equipment checks, exclusion check, handback and defect record.

    Work at height is any work where a person could fall far enough to be injured if precautions were absent; there is no universal two-metre threshold. A fall through a fragile rooflight, from an edge or into an opening can be fatal even during a short task. Survey, method choice, equipment checks, exclusion check, handback and defect record.

    Apply it: What evidence would show that the change improves this task, rather than only completing a record?

    Read this part of the full topicOpen the full topicHSE Managing risk using PPE (Great Britain)HSE step-by-step guide (Great Britain regulator guidance)HSE mobile elevating work platforms (Great Britain construction guidance)
  3. 3. Inspect ageing rooflights without stepping on the roof

    Fictional example: a practical application of the existing topic lesson.

    • Setting: Inspect ageing rooflights without stepping on a suspect roof.
    • Act: Review fragility and whether an internal or MEWP method can reach the task; exclude people below.
    • Hold / review: Hold if roof strength, route or protection is uncertain or wind exceeds the equipment limit.

    Use the selected protected method; maintain edge and opening protection and monitor weather. Leave barriers until access is closed; record defects and owner for repair.

    Apply it: At which point would you hold this example, and what evidence would allow it to proceed?

    Read this part of the full topicOpen the full topicHSE GEIS5 fragile roofs (Great Britain regulator guidance)HSE roof work (Great Britain construction guidance)Work at Height Regulations 2005 (Great Britain law)
  4. 4. How does the work lead to harm? decision table

    Connect the task, the route to the person and the control that can fail.

    • Fragile rooflight or sheet: The surface gives way and a person falls through into the space below.
    • Edge, opening or ladder: A slip or overreach leads to a fall onto a hard or obstructed landing.
    • Dropped tool or material: A person below is struck even though the worker above remains protected.

    Fragile rooflight or sheet: The surface gives way and a person falls through into the space below. Edge, opening or ladder: A slip or overreach leads to a fall onto a hard or obstructed landing. Dropped tool or material: A person below is struck even though the worker above remains protected.

    Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?

    Read this part of the full topicOpen the full topicHSE introduction to working at height safely (Great Britain regulator guidance)HSE roof work (Great Britain construction guidance)HSENI working at height (Northern Ireland regulator information)
  5. 5. Use the work-at-height control sequence

    Start with the stronger practicable options and verify their effect.

    • Avoid height: Use a suitable ground-level inspection or servicing method.
    • Prevent collectively: Provide a suitable guarded platform, edge protection or other collective system.
    • Prevent personally: Use designed restraint only where appropriate to the assessed task.
    • Minimise a fall: Use suitable collective measures before a justified personal fall-arrest system.
    • Verify and rescue: Check equipment, anchors, clearance, weather limits and timely rescue.

    The legal sequence remains avoid, prevent, minimise. Collective protection takes priority over personal protection. Restraint prevents reaching a fall position; fall arrest allows a fall and requires suitable clearance and a planned rescue. Neither establishes that an uncertain roof is sound.

    Apply it: What proves the selected equipment protects this task and permits the planned rescue?

    Read this part of the full topicOpen the full topicHSE Managing risk using PPE (Great Britain)HSE step-by-step guide (Great Britain regulator guidance)HSE mobile elevating work platforms (Great Britain construction guidance)
  6. 6. Use the full working at height lesson

    Follow the official sources below and retain the task-specific evidence.

    • Official guidance: Work at Height Regulations 2005
    • Official guidance: Work at Height Regulations (Northern Ireland) 2005
    • Task decision: Survey, method choice, equipment checks, exclusion check, handback and defect record.

    Apply it: Which official source and full-topic section will you use to resolve the next decision?

    Read this part of the full topicOpen the full topicWork at Height Regulations 2005 (Great Britain law)Work at Height Regulations (Northern Ireland) 2005 (Northern Ireland law)HSE introduction to working at height safely (Great Britain regulator guidance)

Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.

HSE means the Health and Safety Executive for Great Britain; HSENI means the Health and Safety Executive for Northern Ireland. Use the legal and regulator route for the work location.

This can include work above ground, near an opening, or at ground level beside a fragile surface over a void. Assess the actual fall path, not just floor height. Ordinary stairs that form a permanent workplace are not automatically a work-at-height task.

ExposurePossible fallCheck
RooflightThrough a fragile panel.Treat as fragile until verified otherwise.
Open riserFrom the same floor into a void.Guard or cover the opening.
Loading-bay edgeFrom a raised level.Protect edge and vehicle interface.

Sources: Work at Height Regulations 2005; Work at Height Regulations (Northern Ireland) 2005; HSE introduction to working at height safely

How can the hierarchy of controls avoid work at height and reduce remaining fall risks?

Avoid work at height where reasonably practicable; otherwise prevent a fall, then minimise its distance and consequences.

Choose equipment for the actual task and conditions, plan rescue and check that collective measures and the work plan remain effective.

ERICPD (Eliminate, Reduce including substitution, Isolate, Control, personal protective equipment (PPE), Discipline) helps organise the control decision alongside HSE’s five-level hierarchy. For work at height, keep the legal sequence of avoiding the work, preventing a fall and then minimising distance and consequences. Collective protection takes priority over personal protection. A lower-level measure needs a recorded task-based reason when a stronger option cannot be used.

How can the ERICPD hierarchy of controls avoid work at height and reduce remaining fall risks?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

ERICPD promptHSE relationTask-specific measureOwner, verification and stop point
EliminateElimination; avoid work at heightLower a lighting mast for servicing or inspect from a suitable ground-level method so the worker does not need to reach an edge or fragile surface. Check whether the task outcome can be achieved safely from the ground.Facilities or design owner verifies access, reach, electrical interfaces and the completed task. Hold elevated work while a feasible ground-level method remains unevaluated. Basis: HSE step-by-step guide
Reduce, including substitutionSafer method or equipment; it may still require fall preventionWhere the task cannot be completed from the ground, select a suitable guarded platform instead of a ladder for sustained two-handed work. Assess space, ground bearing, access, load, overhead hazards and equipment limits; changing equipment does not by itself remove the fall risk.Competent planner and access-equipment owner verify the selected method against the real task and site. Hold use if the platform cannot be safely positioned, guarded or rescued from. Basis: HSE step-by-step guide; HSE mobile elevating work platforms
IsolateEngineering; collective fall prevention or mitigationInstall suitable edge and opening protection, a guarded working platform or other designed collective system before exposing people. For a fragile roof, prevent access to the fragile area or use an approved protected method; safety nets mitigate a fall only where properly designed and installed.Competent designer or installer checks strength, geometry, fixing and handover. Supervisor verifies the protected route before entry. Stop if a guard, opening cover, support or collective system is missing, altered or uncertain. Basis: HSE roof work; HSE step-by-step guide
ControlAdministrative controls support the physical protectionPlan the sequence, weather limits, exclusion below, equipment inspection and rescue for the actual roof, aisle or façade. Brief the team on access and stop conditions and keep materials and tools from falling.Supervisor checks the work area, current conditions and rescue capability before each shift or changed condition. Hold work when access, weather, an exclusion or a practicable rescue method fails. Basis: HSE assessing all work at height; HSE step-by-step guide
PPEPersonal fall protection where justifiedUse a compatible restraint system to prevent reaching a fall position where appropriate; use fall arrest only with verified anchors, clearance, compatibility and prompt rescue. Select and inspect the complete system for the actual work position and maintain it under competent arrangements.Competent planner verifies system geometry and rescue; trained user checks equipment and connection before use. Stop if an anchor, clearance, equipment condition or rescue provision is uncertain. Basis: HSE step-by-step guide; Work at Height Regulations 2005; Work at Height Regulations (Northern Ireland) 2005
DisciplineSustain every chosen measureMaintain protection, access equipment, inspections, competence and rescue arrangements; control modifications and learn from defects and near misses. Recheck the method after a task, structure, equipment or weather change.Employer and supervisor retain inspection and handover evidence and check repairs in the field. Reopen the plan when repeat defects, unauthorised alterations or changed conditions undermine protection. Basis: HSE introduction to working at height safely; HSE assessing all work at height

How can the ISO 45001 hierarchy of controls avoid work at height and reduce remaining fall risks?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

ERICPD promptHSE relationTask-specific measureOwner, verification and stop point
EliminateElimination; avoid work at heightLower a lighting mast for servicing or inspect from a suitable ground-level method so the worker does not need to reach an edge or fragile surface. Check whether the task outcome can be achieved safely from the ground.Facilities or design owner verifies access, reach, electrical interfaces and the completed task. Hold elevated work while a feasible ground-level method remains unevaluated. Basis: HSE step-by-step guide
Reduce, including substitutionSafer method or equipment; it may still require fall preventionWhere the task cannot be completed from the ground, select a suitable guarded platform instead of a ladder for sustained two-handed work. Assess space, ground bearing, access, load, overhead hazards and equipment limits; changing equipment does not by itself remove the fall risk.Competent planner and access-equipment owner verify the selected method against the real task and site. Hold use if the platform cannot be safely positioned, guarded or rescued from. Basis: HSE step-by-step guide; HSE mobile elevating work platforms
IsolateEngineering; collective fall prevention or mitigationInstall suitable edge and opening protection, a guarded working platform or other designed collective system before exposing people. For a fragile roof, prevent access to the fragile area or use an approved protected method; safety nets mitigate a fall only where properly designed and installed.Competent designer or installer checks strength, geometry, fixing and handover. Supervisor verifies the protected route before entry. Stop if a guard, opening cover, support or collective system is missing, altered or uncertain. Basis: HSE roof work; HSE step-by-step guide
ControlAdministrative controls support the physical protectionPlan the sequence, weather limits, exclusion below, equipment inspection and rescue for the actual roof, aisle or façade. Brief the team on access and stop conditions and keep materials and tools from falling.Supervisor checks the work area, current conditions and rescue capability before each shift or changed condition. Hold work when access, weather, an exclusion or a practicable rescue method fails. Basis: HSE assessing all work at height; HSE step-by-step guide
PPEPersonal fall protection where justifiedUse a compatible restraint system to prevent reaching a fall position where appropriate; use fall arrest only with verified anchors, clearance, compatibility and prompt rescue. Select and inspect the complete system for the actual work position and maintain it under competent arrangements.Competent planner verifies system geometry and rescue; trained user checks equipment and connection before use. Stop if an anchor, clearance, equipment condition or rescue provision is uncertain. Basis: HSE step-by-step guide; Work at Height Regulations 2005; Work at Height Regulations (Northern Ireland) 2005
DisciplineSustain every chosen measureMaintain protection, access equipment, inspections, competence and rescue arrangements; control modifications and learn from defects and near misses. Recheck the method after a task, structure, equipment or weather change.Employer and supervisor retain inspection and handover evidence and check repairs in the field. Reopen the plan when repeat defects, unauthorised alterations or changed conditions undermine protection. Basis: HSE introduction to working at height safely; HSE assessing all work at height

Sources: HSE Work at height

Control-map basis: HSE Managing risk using PPE; HSE step-by-step guide; HSE mobile elevating work platforms; HSE roof work; HSE assessing all work at height; Work at Height Regulations 2005; Work at Height Regulations (Northern Ireland) 2005; HSE introduction to working at height safely

Applied case

A needed item is above reach and a worker proposes climbing the rack. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.

Compare your decision

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.

Lesson 6

People beneath a suspended load

Keep people out of the lift area and have the competent lift planner review the whole operation.

Read the scene evidence

A non-routine lift is being discussed while pedestrians pass through its proposed path.

Identify the condition separately from the exposed person and any possible outcome.

How the harm pathway develops

A suspended load and uncontrolled access below it

A non-routine lift is being discussed while pedestrians pass through its proposed path.

How people can be exposed

A person enters the area into which a load or lifting equipment could move or fall.

Possible harm

Crushing or impact from the load or equipment.

Compare the work arrangements

ArrangementWhat changes exposure?
Uncontrolled arrangementA non-routine lift is being discussed while pedestrians pass through its proposed path. The condition remains unresolved.
Protective responseKeep people out of the lift area and have the competent lift planner review the whole operation.

Select controls by how they prevent harm

Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.

Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.

Control levelApplication to this case
EliminationUse a suitable transfer method that avoids suspending the load over occupied areas.
SubstitutionCompare a safer load unit or handling method after assessing the whole operation.
Engineering controlsSelect suitable lifting equipment and accessories with effective segregation.
Administrative controlsHave a competent person plan, supervise and verify the actual lift and relevant examinations.
PPEUse assessed residual protection; it cannot make standing beneath a load safe.

Verify, communicate and hand back

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.

What does load-handling equipment and lifting operations mean?

It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system.

Best-practice guide · six simple steps

Best-practice guide: Load-Handling Equipment and Lifting Operations

Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.

Step 1 of 6 · StartThis cardPNG imagePDFView full sizeAll 6 cardsPNG images (ZIP)PDF (6 pages)

Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.

Read all six steps as text
  1. 1. What does load-handling equipment and lifting operations mean?

    It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system.

    • Avoid / redesign: Avoid moving the motor by redesigning work at its current position where feasible.
    • Control the task: Use rated lifting gear, secure attachments and a segregated travel route.
    • Verify before release: Planner records feasibility; unclear task holds lift.

    It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system. Choose a safer way to move the load before designing a lift.

    Apply it: Which part of this plan would you check at the workface before authorising the task?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)
  2. 2. Turn load-handling equipment and lifting operations knowledge into a decision

    Use the evidence to improve the actual work arrangement.

    • Change at source: Avoid moving the motor by redesigning work at its current position where feasible.
    • Make it observable: Planner records feasibility; unclear task holds lift.
    • Keep useful evidence: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Choose a safer way to move the load before designing a lift. Where lifting equipment is needed, a competent person plans the operation, selects equipment and accessories for the load and environment, keeps people away from a suspended load and verifies pre-use checks, maintenance and statutory examination. Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Apply it: What evidence would show that the change improves this task, rather than only completing a record?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  3. 3. Worked lifting assessment example

    Fictional example: a practical application of the existing topic lesson.

    • Load: What is being lifted and where is the centre of gravity?
    • Equipment: Is the lift truck and attachment suitable?
    • Route: Can the load travel safely?

    Load: What is being lifted and where is the centre of gravity? Evidence / response: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet. Equipment: Is the lift truck and attachment suitable? Evidence / response: Correct rated capacity, fork length suitable, daily check complete.

    Apply it: At which point would you hold this example, and what evidence would allow it to proceed?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  4. 4. Follow the load and the people in its path

    Connect the task, the route to the person and the control that can fail.

    • Load failure: An unsuitable attachment or insecure load can fall or shift.
    • Movement: A swinging load or moving lifting equipment can trap or strike people.
    • Stability: Ground, capacity or setup failures can overturn equipment or destabilise the lift.

    An unsuitable attachment or insecure load can fall or shift. A swinging load or moving lifting equipment can trap or strike people. Ground, capacity or setup failures can overturn equipment or destabilise the lift. Use the full topic for the detailed mechanism, task limits and source scope.

    Apply it: Where is this harm route present in the actual work, and which control breaks it before anyone is exposed?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)
  5. 5. Choose controls for load-handling equipment and lifting operations

    Start with the stronger practicable options and verify their effect.

    • Eliminate: Avoid moving the motor by redesigning work at its current position where feasible.
    • Reduce: Use a lighter modular component or a lower-risk delivery/move method.
    • Isolate: Use rated lifting gear, secure attachments and a segregated travel route.
    • Control: Approved lift plan, signaler, exclusion, weather/ground checks and communication.
    • PPE: Head, foot, hand protection for residual contact hazard.

    Eliminate: Avoid moving the motor by redesigning work at its current position where feasible. Reduce: Use a lighter modular component or a lower-risk delivery/move method. Isolate: Use rated lifting gear, secure attachments and a segregated travel route. Control: Approved lift plan, signaler, exclusion, weather/ground checks and communication. PPE: Head, foot, hand protection for residual contact hazard. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.

    Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  6. 6. Use the full load-handling equipment and lifting operations lesson

    Follow the official sources below and retain the task-specific evidence.

    • Official guidance: LOLER overview
    • Official guidance: Safe use of lifting equipment (L113)
    • Task decision: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Apply it: Which official source and full-topic section will you use to resolve the next decision?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)

Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.

This topic sits between manual handling, work equipment, workplace transport and lifting operations. A sack truck, trolley or pallet truck may reduce manual handling effort, but it can introduce new risks such as runaway loads, poor steering, trapping, slopes, unsuitable wheels or overloading. A crane, hoist, lift truck or lifting accessory can remove manual effort but creates higher-energy hazards such as suspended loads, overturning, dropped loads, crushing, striking structures or instability.

The first professional judgement is whether the load needs to be handled at all. Can the task be eliminated, delivered closer to the point of use, split into smaller units, palletised, mechanised, redesigned or completed at a better height? If handling remains, the task, individual, load and environment still matter. If lifting equipment is used, the organisation must also consider suitability, strength, stability, marking, pre-use checks, maintenance, inspection, thorough examination, competent planning and supervision.

For learners, the key is not to memorise equipment names. The useful mental model is: what is the load, how will it move, what could fail, who could be struck, trapped, fall or strain, what prevents the event, and what evidence proves the control is live today?

Lifting Operations and Lifting Equipment Regulations (LOLER) scope depends on what the equipment actually does. HSE’s LOLER overview says simple pallet trucks that raise a load only just clear of the ground, and many conveyors, are outside LOLER but remain subject to the Provision and Use of Work Equipment Regulations (PUWER). HSE L113 identifies high-lift pallet trucks able to raise forks above 300 mm as LOLER examples. Do not assign the LOLER six-/12-month examination cycle to every load-handling aid; first check whether it is lifting equipment within scope.

Equipment or activityWhat it is used forMain risk questions
Sack trucks and trolleysMoving smaller loads over short distances.Is the load stable, route suitable, slope controlled and pushing/pulling force reasonable?
Pallet trucksMoving palletised loads on suitable floors.Is the pallet sound, floor level, load within capacity and pedestrian route controlled?
People-handling aidsReducing manual effort in health and social care or assisted movement.Is the aid suitable for the person, maintained and used by trained workers?
Fork-lift trucksLifting and transporting palletised or compatible loads.Is the operator trained, load secure, route segregated and attachment suitable?
Hoists and lifting accessoriesRaising, lowering or positioning loads.Is the safe working load / working load limit marked, accessory compatible and pre-use check complete?
ConveyorsMoving loads continuously through a process.Are trapping points guarded, emergency stops working and maintenance isolated?
Cranes and complex liftsMoving heavier, unusual or high-risk loads.Is there a competent lifting plan, appointed person, exclusion zone and ground/load assessment?

How can the hierarchy of controls prevent dropped loads and unsafe lifting operations?

Remove the need for hazardous handling where feasible, then select equipment and controls for the residual lift.

Eliminate, Reduce, Isolate, Control, Personal protective equipment (PPE) and Discipline (ERICPD) below maps to the five-level hierarchy for a motor lifted from a workshop bay. HSE lifting overview sets the planning and equipment principles. The supervisor holds the move if load identity, attachment, travel clearance or equipment condition is uncertain.

The five levels are elimination, substitution, engineering, administrative controls and PPE. “Discipline” is the sustained inspection, feedback and repair that keeps each selected level effective.

How can the ERICPD hierarchy of controls prevent dropped loads and unsafe lifting operations?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Task application for Load-Handling Equipment and Lifting Operations
Activity and release context
Eliminate, Reduce, Isolate, Control, Personal protective equipment (PPE) and Discipline (ERICPD) below maps to the five-level hierarchy for a motor lifted from a workshop bay. HSE lifting overview sets the planning and equipment principles. The supervisor holds the move if load identity, attachment, travel clearance or equipment condition is uncertain.
Full example
Read the activity, checks and hand-back in context
ERICPDFive-level hierarchyMotor-move choiceOwner, proof and stop
EliminateEliminationAvoid moving the motor by redesigning work at its current position where feasible.Planner records feasibility; unclear task holds lift.
ReduceSubstitutionUse a lighter modular component or a lower-risk delivery/move method.Engineering verifies compatibility and mass.
Isolate / ControlEngineering controlsUse rated lifting gear, secure attachments and a segregated travel route.Lift supervisor checks setup; failed rating or attachment stops move.
ControlAdministrative controlsApproved lift plan, signaler, exclusion, weather/ground checks and communication.Supervisor briefs crew; change in route or load triggers hold.
PPEPPEHead, foot, hand protection for residual contact hazard.Selector checks suitability; PPE never justifies entry under load.
DisciplineSustaining all levelsRecord checks, defects, examination, repairs and near misses.Manager verifies hand-back and recurring defect review.

How can the ISO 45001 hierarchy of controls prevent dropped loads and unsafe lifting operations?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Task application for Load-Handling Equipment and Lifting Operations
Activity and release context
Eliminate, Reduce, Isolate, Control, Personal protective equipment (PPE) and Discipline (ERICPD) below maps to the five-level hierarchy for a motor lifted from a workshop bay. HSE lifting overview sets the planning and equipment principles. The supervisor holds the move if load identity, attachment, travel clearance or equipment condition is uncertain.
Full example
Read the activity, checks and hand-back in context
ERICPDFive-level hierarchyMotor-move choiceOwner, proof and stop
EliminateEliminationAvoid moving the motor by redesigning work at its current position where feasible.Planner records feasibility; unclear task holds lift.
ReduceSubstitutionUse a lighter modular component or a lower-risk delivery/move method.Engineering verifies compatibility and mass.
Isolate / ControlEngineering controlsUse rated lifting gear, secure attachments and a segregated travel route.Lift supervisor checks setup; failed rating or attachment stops move.
ControlAdministrative controlsApproved lift plan, signaler, exclusion, weather/ground checks and communication.Supervisor briefs crew; change in route or load triggers hold.
PPEPPEHead, foot, hand protection for residual contact hazard.Selector checks suitability; PPE never justifies entry under load.
DisciplineSustaining all levelsRecord checks, defects, examination, repairs and near misses.Manager verifies hand-back and recurring defect review.

Applied case

A non-routine lift is being discussed while pedestrians pass through its proposed path. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.

Compare your decision

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.

Lesson 7

A heavier product in a changed storage bay

Hold the proposed storage change and obtain the load and system information needed for a competent design and handling check.

Read the scene evidence

A new product and altered beam arrangement have been introduced without confirming the storage system design.

Identify the condition separately from the exposed person and any possible outcome.

How the harm pathway develops

A load or configuration outside demonstrated storage capacity

A new product and altered beam arrangement have been introduced without confirming the storage system design.

How people can be exposed

Stock is placed where the floor, rack or handling arrangement may not support it safely.

Possible harm

Falling stock, structural failure or loss of handling stability.

Compare the work arrangements

ArrangementWhat changes exposure?
Uncontrolled arrangementA new product and altered beam arrangement have been introduced without confirming the storage system design. The condition remains unresolved.
Protective responseHold the proposed storage change and obtain the load and system information needed for a competent design and handling check.

Select controls by how they prevent harm

Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.

Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.

Control levelApplication to this case
EliminationAvoid the unsuitable storage arrangement through product and layout planning.
SubstitutionChoose a suitable storage and load-unit method for the actual product.
Engineering controlsProvide correctly designed, installed and rated storage and load support.
Administrative controlsControl changes to load weights, beam settings, layout and handling equipment through competent review.
PPEPPE cannot increase the capacity of a rack or floor.

Verify, communicate and hand back

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.

What does load-handling equipment and lifting operations mean?

It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system.

Best-practice guide · six simple steps

Best-practice guide: Load-Handling Equipment and Lifting Operations

Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.

Step 1 of 6 · StartThis cardPNG imagePDFView full sizeAll 6 cardsPNG images (ZIP)PDF (6 pages)

Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.

Read all six steps as text
  1. 1. What does load-handling equipment and lifting operations mean?

    It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system.

    • Avoid / redesign: Avoid moving the motor by redesigning work at its current position where feasible.
    • Control the task: Use rated lifting gear, secure attachments and a segregated travel route.
    • Verify before release: Planner records feasibility; unclear task holds lift.

    It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system. Choose a safer way to move the load before designing a lift.

    Apply it: Which part of this plan would you check at the workface before authorising the task?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)
  2. 2. Turn load-handling equipment and lifting operations knowledge into a decision

    Use the evidence to improve the actual work arrangement.

    • Change at source: Avoid moving the motor by redesigning work at its current position where feasible.
    • Make it observable: Planner records feasibility; unclear task holds lift.
    • Keep useful evidence: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Choose a safer way to move the load before designing a lift. Where lifting equipment is needed, a competent person plans the operation, selects equipment and accessories for the load and environment, keeps people away from a suspended load and verifies pre-use checks, maintenance and statutory examination. Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Apply it: What evidence would show that the change improves this task, rather than only completing a record?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  3. 3. Worked lifting assessment example

    Fictional example: a practical application of the existing topic lesson.

    • Load: What is being lifted and where is the centre of gravity?
    • Equipment: Is the lift truck and attachment suitable?
    • Route: Can the load travel safely?

    Load: What is being lifted and where is the centre of gravity? Evidence / response: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet. Equipment: Is the lift truck and attachment suitable? Evidence / response: Correct rated capacity, fork length suitable, daily check complete.

    Apply it: At which point would you hold this example, and what evidence would allow it to proceed?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  4. 4. Follow the load and the people in its path

    Connect the task, the route to the person and the control that can fail.

    • Load failure: An unsuitable attachment or insecure load can fall or shift.
    • Movement: A swinging load or moving lifting equipment can trap or strike people.
    • Stability: Ground, capacity or setup failures can overturn equipment or destabilise the lift.

    An unsuitable attachment or insecure load can fall or shift. A swinging load or moving lifting equipment can trap or strike people. Ground, capacity or setup failures can overturn equipment or destabilise the lift. Use the full topic for the detailed mechanism, task limits and source scope.

    Apply it: Where is this harm route present in the actual work, and which control breaks it before anyone is exposed?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)
  5. 5. Choose controls for load-handling equipment and lifting operations

    Start with the stronger practicable options and verify their effect.

    • Eliminate: Avoid moving the motor by redesigning work at its current position where feasible.
    • Reduce: Use a lighter modular component or a lower-risk delivery/move method.
    • Isolate: Use rated lifting gear, secure attachments and a segregated travel route.
    • Control: Approved lift plan, signaler, exclusion, weather/ground checks and communication.
    • PPE: Head, foot, hand protection for residual contact hazard.

    Eliminate: Avoid moving the motor by redesigning work at its current position where feasible. Reduce: Use a lighter modular component or a lower-risk delivery/move method. Isolate: Use rated lifting gear, secure attachments and a segregated travel route. Control: Approved lift plan, signaler, exclusion, weather/ground checks and communication. PPE: Head, foot, hand protection for residual contact hazard. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.

    Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  6. 6. Use the full load-handling equipment and lifting operations lesson

    Follow the official sources below and retain the task-specific evidence.

    • Official guidance: LOLER overview
    • Official guidance: Safe use of lifting equipment (L113)
    • Task decision: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Apply it: Which official source and full-topic section will you use to resolve the next decision?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)

Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.

This topic sits between manual handling, work equipment, workplace transport and lifting operations. A sack truck, trolley or pallet truck may reduce manual handling effort, but it can introduce new risks such as runaway loads, poor steering, trapping, slopes, unsuitable wheels or overloading. A crane, hoist, lift truck or lifting accessory can remove manual effort but creates higher-energy hazards such as suspended loads, overturning, dropped loads, crushing, striking structures or instability.

The first professional judgement is whether the load needs to be handled at all. Can the task be eliminated, delivered closer to the point of use, split into smaller units, palletised, mechanised, redesigned or completed at a better height? If handling remains, the task, individual, load and environment still matter. If lifting equipment is used, the organisation must also consider suitability, strength, stability, marking, pre-use checks, maintenance, inspection, thorough examination, competent planning and supervision.

For learners, the key is not to memorise equipment names. The useful mental model is: what is the load, how will it move, what could fail, who could be struck, trapped, fall or strain, what prevents the event, and what evidence proves the control is live today?

Lifting Operations and Lifting Equipment Regulations (LOLER) scope depends on what the equipment actually does. HSE’s LOLER overview says simple pallet trucks that raise a load only just clear of the ground, and many conveyors, are outside LOLER but remain subject to the Provision and Use of Work Equipment Regulations (PUWER). HSE L113 identifies high-lift pallet trucks able to raise forks above 300 mm as LOLER examples. Do not assign the LOLER six-/12-month examination cycle to every load-handling aid; first check whether it is lifting equipment within scope.

Equipment or activityWhat it is used forMain risk questions
Sack trucks and trolleysMoving smaller loads over short distances.Is the load stable, route suitable, slope controlled and pushing/pulling force reasonable?
Pallet trucksMoving palletised loads on suitable floors.Is the pallet sound, floor level, load within capacity and pedestrian route controlled?
People-handling aidsReducing manual effort in health and social care or assisted movement.Is the aid suitable for the person, maintained and used by trained workers?
Fork-lift trucksLifting and transporting palletised or compatible loads.Is the operator trained, load secure, route segregated and attachment suitable?
Hoists and lifting accessoriesRaising, lowering or positioning loads.Is the safe working load / working load limit marked, accessory compatible and pre-use check complete?
ConveyorsMoving loads continuously through a process.Are trapping points guarded, emergency stops working and maintenance isolated?
Cranes and complex liftsMoving heavier, unusual or high-risk loads.Is there a competent lifting plan, appointed person, exclusion zone and ground/load assessment?

How can the hierarchy of controls prevent dropped loads and unsafe lifting operations?

Remove the need for hazardous handling where feasible, then select equipment and controls for the residual lift.

Eliminate, Reduce, Isolate, Control, Personal protective equipment (PPE) and Discipline (ERICPD) below maps to the five-level hierarchy for a motor lifted from a workshop bay. HSE lifting overview sets the planning and equipment principles. The supervisor holds the move if load identity, attachment, travel clearance or equipment condition is uncertain.

The five levels are elimination, substitution, engineering, administrative controls and PPE. “Discipline” is the sustained inspection, feedback and repair that keeps each selected level effective.

How can the ERICPD hierarchy of controls prevent dropped loads and unsafe lifting operations?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Task application for Load-Handling Equipment and Lifting Operations
Activity and release context
Eliminate, Reduce, Isolate, Control, Personal protective equipment (PPE) and Discipline (ERICPD) below maps to the five-level hierarchy for a motor lifted from a workshop bay. HSE lifting overview sets the planning and equipment principles. The supervisor holds the move if load identity, attachment, travel clearance or equipment condition is uncertain.
Full example
Read the activity, checks and hand-back in context
ERICPDFive-level hierarchyMotor-move choiceOwner, proof and stop
EliminateEliminationAvoid moving the motor by redesigning work at its current position where feasible.Planner records feasibility; unclear task holds lift.
ReduceSubstitutionUse a lighter modular component or a lower-risk delivery/move method.Engineering verifies compatibility and mass.
Isolate / ControlEngineering controlsUse rated lifting gear, secure attachments and a segregated travel route.Lift supervisor checks setup; failed rating or attachment stops move.
ControlAdministrative controlsApproved lift plan, signaler, exclusion, weather/ground checks and communication.Supervisor briefs crew; change in route or load triggers hold.
PPEPPEHead, foot, hand protection for residual contact hazard.Selector checks suitability; PPE never justifies entry under load.
DisciplineSustaining all levelsRecord checks, defects, examination, repairs and near misses.Manager verifies hand-back and recurring defect review.

How can the ISO 45001 hierarchy of controls prevent dropped loads and unsafe lifting operations?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Task application for Load-Handling Equipment and Lifting Operations
Activity and release context
Eliminate, Reduce, Isolate, Control, Personal protective equipment (PPE) and Discipline (ERICPD) below maps to the five-level hierarchy for a motor lifted from a workshop bay. HSE lifting overview sets the planning and equipment principles. The supervisor holds the move if load identity, attachment, travel clearance or equipment condition is uncertain.
Full example
Read the activity, checks and hand-back in context
ERICPDFive-level hierarchyMotor-move choiceOwner, proof and stop
EliminateEliminationAvoid moving the motor by redesigning work at its current position where feasible.Planner records feasibility; unclear task holds lift.
ReduceSubstitutionUse a lighter modular component or a lower-risk delivery/move method.Engineering verifies compatibility and mass.
Isolate / ControlEngineering controlsUse rated lifting gear, secure attachments and a segregated travel route.Lift supervisor checks setup; failed rating or attachment stops move.
ControlAdministrative controlsApproved lift plan, signaler, exclusion, weather/ground checks and communication.Supervisor briefs crew; change in route or load triggers hold.
PPEPPEHead, foot, hand protection for residual contact hazard.Selector checks suitability; PPE never justifies entry under load.
DisciplineSustaining all levelsRecord checks, defects, examination, repairs and near misses.Manager verifies hand-back and recurring defect review.

Applied case

A new product and altered beam arrangement have been introduced without confirming the storage system design. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.

Compare your decision

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.

Lesson 8

Loose stock above a picking position

Keep people outside the possible fall area and hold affected picking and replenishment. Request a planned recovery using suitable equipment and competent people.

Read the scene evidence

A loose carton protrudes from an upper storage location. Picking continues underneath while replenishment is being planned.

Identify the condition separately from the exposed person and any possible outcome.

How the harm pathway develops

Unsecured items are stored above an occupied picking position.

A loose carton protrudes from an upper storage location. Picking continues underneath while replenishment is being planned.

How people can be exposed

A person below can be in the fall path if stock is disturbed or loses support.

Possible harm

Falling stock could strike someone and cause serious head or body injury.

Compare the work arrangements

ArrangementWhat changes exposure?
Uncontrolled arrangementA loose carton protrudes from an upper storage location. Picking continues underneath while replenishment is being planned. The condition remains unresolved.
Protective responseKeep people outside the possible fall area and hold affected picking and replenishment. Request a planned recovery using suitable equipment and competent people.

Select controls by how they prevent harm

Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.

Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.

Control levelApplication to this case
EliminationRelocate the stock so routine work does not take place below loose overhead items.
SubstitutionUse a suitable contained load or lower storage position after checking capacity and handling risks.
Engineering controlsProvide designed storage containment and suitable protection against falling objects for the actual arrangement.
Administrative controlsPlan recovery, separate replenishment from picking, and inspect storage after changes or damage.
PPEUse assessed head and foot protection for residual risk; a helmet does not make standing below unsecured stock acceptable.

Verify, communicate and hand back

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.

What counts as work at height?

It is work in any place where a person could fall a distance liable to cause personal injury if precautions were absent; there is no universal two-metre trigger.

Best-practice guide · six simple steps

Best-practice guide: Working at Height

Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.

Step 1 of 6 · StartThis cardPNG imagePDFView full sizeAll 6 cardsPNG images (ZIP)PDF (6 pages)

Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.

Read all six steps as text
  1. 1. Avoid height, then prevent the remaining fall

    Use the actual task, structure and conditions to choose the method.

    • Avoid: Complete the task from ground level where reasonably practicable.
    • Prevent: Use a suitable safe place or collective fall prevention where work at height remains.
    • Minimise: Plan the distance, consequences and rescue for a remaining fall risk.

    Keep the work-at-height sequence: avoid the work where reasonably practicable, prevent falls, then minimise the distance and consequences of a remaining fall. Choose collective protection before personal protection at each level. A short task or a fall below two metres can still cause severe injury.

    Apply it: Can the task be completed without approaching a fragile surface, opening or unprotected edge?

    Read this part of the full topicOpen the full topicWork at Height Regulations 2005 (Great Britain law)Work at Height Regulations (Northern Ireland) 2005 (Northern Ireland law)HSE introduction to working at height safely (Great Britain regulator guidance)
  2. 2. Turn working at height knowledge into a decision

    Use the evidence to improve the actual work arrangement.

    • Change at source: Lower a lighting mast for servicing or inspect from a suitable ground-level method so the worker does not need to reach an edge or fragile surface.
    • Make it observable: Facilities or design owner verifies access, reach, electrical interfaces and the completed task.
    • Keep useful evidence: Survey, method choice, equipment checks, exclusion check, handback and defect record.

    Work at height is any work where a person could fall far enough to be injured if precautions were absent; there is no universal two-metre threshold. A fall through a fragile rooflight, from an edge or into an opening can be fatal even during a short task. Survey, method choice, equipment checks, exclusion check, handback and defect record.

    Apply it: What evidence would show that the change improves this task, rather than only completing a record?

    Read this part of the full topicOpen the full topicHSE Managing risk using PPE (Great Britain)HSE step-by-step guide (Great Britain regulator guidance)HSE mobile elevating work platforms (Great Britain construction guidance)
  3. 3. Inspect ageing rooflights without stepping on the roof

    Fictional example: a practical application of the existing topic lesson.

    • Setting: Inspect ageing rooflights without stepping on a suspect roof.
    • Act: Review fragility and whether an internal or MEWP method can reach the task; exclude people below.
    • Hold / review: Hold if roof strength, route or protection is uncertain or wind exceeds the equipment limit.

    Use the selected protected method; maintain edge and opening protection and monitor weather. Leave barriers until access is closed; record defects and owner for repair.

    Apply it: At which point would you hold this example, and what evidence would allow it to proceed?

    Read this part of the full topicOpen the full topicHSE GEIS5 fragile roofs (Great Britain regulator guidance)HSE roof work (Great Britain construction guidance)Work at Height Regulations 2005 (Great Britain law)
  4. 4. How does the work lead to harm? decision table

    Connect the task, the route to the person and the control that can fail.

    • Fragile rooflight or sheet: The surface gives way and a person falls through into the space below.
    • Edge, opening or ladder: A slip or overreach leads to a fall onto a hard or obstructed landing.
    • Dropped tool or material: A person below is struck even though the worker above remains protected.

    Fragile rooflight or sheet: The surface gives way and a person falls through into the space below. Edge, opening or ladder: A slip or overreach leads to a fall onto a hard or obstructed landing. Dropped tool or material: A person below is struck even though the worker above remains protected.

    Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?

    Read this part of the full topicOpen the full topicHSE introduction to working at height safely (Great Britain regulator guidance)HSE roof work (Great Britain construction guidance)HSENI working at height (Northern Ireland regulator information)
  5. 5. Use the work-at-height control sequence

    Start with the stronger practicable options and verify their effect.

    • Avoid height: Use a suitable ground-level inspection or servicing method.
    • Prevent collectively: Provide a suitable guarded platform, edge protection or other collective system.
    • Prevent personally: Use designed restraint only where appropriate to the assessed task.
    • Minimise a fall: Use suitable collective measures before a justified personal fall-arrest system.
    • Verify and rescue: Check equipment, anchors, clearance, weather limits and timely rescue.

    The legal sequence remains avoid, prevent, minimise. Collective protection takes priority over personal protection. Restraint prevents reaching a fall position; fall arrest allows a fall and requires suitable clearance and a planned rescue. Neither establishes that an uncertain roof is sound.

    Apply it: What proves the selected equipment protects this task and permits the planned rescue?

    Read this part of the full topicOpen the full topicHSE Managing risk using PPE (Great Britain)HSE step-by-step guide (Great Britain regulator guidance)HSE mobile elevating work platforms (Great Britain construction guidance)
  6. 6. Use the full working at height lesson

    Follow the official sources below and retain the task-specific evidence.

    • Official guidance: Work at Height Regulations 2005
    • Official guidance: Work at Height Regulations (Northern Ireland) 2005
    • Task decision: Survey, method choice, equipment checks, exclusion check, handback and defect record.

    Apply it: Which official source and full-topic section will you use to resolve the next decision?

    Read this part of the full topicOpen the full topicWork at Height Regulations 2005 (Great Britain law)Work at Height Regulations (Northern Ireland) 2005 (Northern Ireland law)HSE introduction to working at height safely (Great Britain regulator guidance)

Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.

HSE means the Health and Safety Executive for Great Britain; HSENI means the Health and Safety Executive for Northern Ireland. Use the legal and regulator route for the work location.

This can include work above ground, near an opening, or at ground level beside a fragile surface over a void. Assess the actual fall path, not just floor height. Ordinary stairs that form a permanent workplace are not automatically a work-at-height task.

ExposurePossible fallCheck
RooflightThrough a fragile panel.Treat as fragile until verified otherwise.
Open riserFrom the same floor into a void.Guard or cover the opening.
Loading-bay edgeFrom a raised level.Protect edge and vehicle interface.

Sources: Work at Height Regulations 2005; Work at Height Regulations (Northern Ireland) 2005; HSE introduction to working at height safely

How can the hierarchy of controls avoid work at height and reduce remaining fall risks?

Avoid work at height where reasonably practicable; otherwise prevent a fall, then minimise its distance and consequences.

Choose equipment for the actual task and conditions, plan rescue and check that collective measures and the work plan remain effective.

ERICPD (Eliminate, Reduce including substitution, Isolate, Control, personal protective equipment (PPE), Discipline) helps organise the control decision alongside HSE’s five-level hierarchy. For work at height, keep the legal sequence of avoiding the work, preventing a fall and then minimising distance and consequences. Collective protection takes priority over personal protection. A lower-level measure needs a recorded task-based reason when a stronger option cannot be used.

How can the ERICPD hierarchy of controls avoid work at height and reduce remaining fall risks?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

ERICPD promptHSE relationTask-specific measureOwner, verification and stop point
EliminateElimination; avoid work at heightLower a lighting mast for servicing or inspect from a suitable ground-level method so the worker does not need to reach an edge or fragile surface. Check whether the task outcome can be achieved safely from the ground.Facilities or design owner verifies access, reach, electrical interfaces and the completed task. Hold elevated work while a feasible ground-level method remains unevaluated. Basis: HSE step-by-step guide
Reduce, including substitutionSafer method or equipment; it may still require fall preventionWhere the task cannot be completed from the ground, select a suitable guarded platform instead of a ladder for sustained two-handed work. Assess space, ground bearing, access, load, overhead hazards and equipment limits; changing equipment does not by itself remove the fall risk.Competent planner and access-equipment owner verify the selected method against the real task and site. Hold use if the platform cannot be safely positioned, guarded or rescued from. Basis: HSE step-by-step guide; HSE mobile elevating work platforms
IsolateEngineering; collective fall prevention or mitigationInstall suitable edge and opening protection, a guarded working platform or other designed collective system before exposing people. For a fragile roof, prevent access to the fragile area or use an approved protected method; safety nets mitigate a fall only where properly designed and installed.Competent designer or installer checks strength, geometry, fixing and handover. Supervisor verifies the protected route before entry. Stop if a guard, opening cover, support or collective system is missing, altered or uncertain. Basis: HSE roof work; HSE step-by-step guide
ControlAdministrative controls support the physical protectionPlan the sequence, weather limits, exclusion below, equipment inspection and rescue for the actual roof, aisle or façade. Brief the team on access and stop conditions and keep materials and tools from falling.Supervisor checks the work area, current conditions and rescue capability before each shift or changed condition. Hold work when access, weather, an exclusion or a practicable rescue method fails. Basis: HSE assessing all work at height; HSE step-by-step guide
PPEPersonal fall protection where justifiedUse a compatible restraint system to prevent reaching a fall position where appropriate; use fall arrest only with verified anchors, clearance, compatibility and prompt rescue. Select and inspect the complete system for the actual work position and maintain it under competent arrangements.Competent planner verifies system geometry and rescue; trained user checks equipment and connection before use. Stop if an anchor, clearance, equipment condition or rescue provision is uncertain. Basis: HSE step-by-step guide; Work at Height Regulations 2005; Work at Height Regulations (Northern Ireland) 2005
DisciplineSustain every chosen measureMaintain protection, access equipment, inspections, competence and rescue arrangements; control modifications and learn from defects and near misses. Recheck the method after a task, structure, equipment or weather change.Employer and supervisor retain inspection and handover evidence and check repairs in the field. Reopen the plan when repeat defects, unauthorised alterations or changed conditions undermine protection. Basis: HSE introduction to working at height safely; HSE assessing all work at height

How can the ISO 45001 hierarchy of controls avoid work at height and reduce remaining fall risks?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

ERICPD promptHSE relationTask-specific measureOwner, verification and stop point
EliminateElimination; avoid work at heightLower a lighting mast for servicing or inspect from a suitable ground-level method so the worker does not need to reach an edge or fragile surface. Check whether the task outcome can be achieved safely from the ground.Facilities or design owner verifies access, reach, electrical interfaces and the completed task. Hold elevated work while a feasible ground-level method remains unevaluated. Basis: HSE step-by-step guide
Reduce, including substitutionSafer method or equipment; it may still require fall preventionWhere the task cannot be completed from the ground, select a suitable guarded platform instead of a ladder for sustained two-handed work. Assess space, ground bearing, access, load, overhead hazards and equipment limits; changing equipment does not by itself remove the fall risk.Competent planner and access-equipment owner verify the selected method against the real task and site. Hold use if the platform cannot be safely positioned, guarded or rescued from. Basis: HSE step-by-step guide; HSE mobile elevating work platforms
IsolateEngineering; collective fall prevention or mitigationInstall suitable edge and opening protection, a guarded working platform or other designed collective system before exposing people. For a fragile roof, prevent access to the fragile area or use an approved protected method; safety nets mitigate a fall only where properly designed and installed.Competent designer or installer checks strength, geometry, fixing and handover. Supervisor verifies the protected route before entry. Stop if a guard, opening cover, support or collective system is missing, altered or uncertain. Basis: HSE roof work; HSE step-by-step guide
ControlAdministrative controls support the physical protectionPlan the sequence, weather limits, exclusion below, equipment inspection and rescue for the actual roof, aisle or façade. Brief the team on access and stop conditions and keep materials and tools from falling.Supervisor checks the work area, current conditions and rescue capability before each shift or changed condition. Hold work when access, weather, an exclusion or a practicable rescue method fails. Basis: HSE assessing all work at height; HSE step-by-step guide
PPEPersonal fall protection where justifiedUse a compatible restraint system to prevent reaching a fall position where appropriate; use fall arrest only with verified anchors, clearance, compatibility and prompt rescue. Select and inspect the complete system for the actual work position and maintain it under competent arrangements.Competent planner verifies system geometry and rescue; trained user checks equipment and connection before use. Stop if an anchor, clearance, equipment condition or rescue provision is uncertain. Basis: HSE step-by-step guide; Work at Height Regulations 2005; Work at Height Regulations (Northern Ireland) 2005
DisciplineSustain every chosen measureMaintain protection, access equipment, inspections, competence and rescue arrangements; control modifications and learn from defects and near misses. Recheck the method after a task, structure, equipment or weather change.Employer and supervisor retain inspection and handover evidence and check repairs in the field. Reopen the plan when repeat defects, unauthorised alterations or changed conditions undermine protection. Basis: HSE introduction to working at height safely; HSE assessing all work at height

Sources: HSE Work at height

Control-map basis: HSE Managing risk using PPE; HSE step-by-step guide; HSE mobile elevating work platforms; HSE roof work; HSE assessing all work at height; Work at Height Regulations 2005; Work at Height Regulations (Northern Ireland) 2005; HSE introduction to working at height safely

Applied case

A loose carton protrudes from an upper storage location. Picking continues underneath while replenishment is being planned. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.

Compare your decision

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.

Lesson 9

A shelf has been altered without a capacity check

Restrict use of the affected bay and ask the storage-system owner for competent review. Do not load it, climb it or attempt an improvised repair.

Read the scene evidence

A beam has been moved and a board added to create another picking shelf. Stock is ready to go on it, but no one can confirm the revised capacity or approval.

Identify the condition separately from the exposed person and any possible outcome.

How the harm pathway develops

A changed shelf arrangement has no confirmed support or loading basis.

A beam has been moved and a board added to create another picking shelf. Stock is ready to go on it, but no one can confirm the revised capacity or approval.

How people can be exposed

Loading or reaching into the altered bay can put people beside unsupported or overloaded storage.

Possible harm

Shelf or load failure could cause falling items, crushing or a wider storage collapse.

Compare the work arrangements

ArrangementWhat changes exposure?
Uncontrolled arrangementA beam has been moved and a board added to create another picking shelf. Stock is ready to go on it, but no one can confirm the revised capacity or approval. The condition remains unresolved.
Protective responseRestrict use of the affected bay and ask the storage-system owner for competent review. Do not load it, climb it or attempt an improvised repair.

Select controls by how they prevent harm

Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.

Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.

Control levelApplication to this case
EliminationRemove the unapproved storage arrangement from the work plan and provide a verified alternative location.
SubstitutionSelect a suitable designed storage unit for the actual goods instead of an improvised shelf.
Engineering controlsHave suitable supports, restraints and rated components specified and installed by competent people.
Administrative controlsControl alterations, communicate load limits and inspect defects with clear hold and release authority.
PPEUse assessed residual protection for authorised handling; it cannot stop a shelf collapse.

Verify, communicate and hand back

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.

When is a PUWER inspection needed?

In Great Britain, inspection is required where safety depends on installation, where deterioration could cause danger, or after exceptional circumstances liable to jeopardise safety. The NI instrument is separate and must be checked for the NI workplace.

A reinstalled machine may need inspection before first use at the new location. Deteriorating equipment needs suitable intervals set by risk. Major modification, suspected serious damage or a substantial change of use can trigger an additional inspection. Not every item needs a formal inspection; a low-risk item may be adequately checked before use. Keep the inspection result and act on defects. HSE inspection of work equipment and HSENI PUWER 1999.

Inspection evidence follows the equipment

For GB PUWER inspection, retain the result at least until the next inspection and ensure equipment moving between undertakings has physical evidence of the last required inspection. Check scope, result, restrictions and next trigger before use. This is separate from LOLER/PSSR examination-record retention. NI uses its own PUWER route. HSE: inspection of work equipment.

How can the ISO 45001 hierarchy of controls reduce machinery risks during maintenance, inspection and testing?

Choose the safe intervention and test method before a maintainer approaches danger. Design out unnecessary access, use engineered separation and secure isolation for the planned work, then support those measures with competent instruction, controlled tests and residual PPE.

Illustrative decision: BuildOut replaces a conveyor bearing and checks the protective interlock. Mechanical repair and demonstration of the safety function are separate tasks. The engineer specifies the isolation and the protected test; the supervisor coordinates operators, cleaners and linked equipment.

ERICPD means Eliminate, Reduce (including substitution), Isolate, Control, PPE and Discipline. The five-level hierarchy groups measures as elimination, substitution, engineering controls, administrative controls and PPE. They overlap: isolation is usually an engineering measure; control can include engineered and administrative measures. Discipline means maintaining and checking the controls, supervising the method and learning from defects, rather than blaming someone or accepting weaker protection.

How can the ERICPD hierarchy of controls reduce machinery risks during maintenance, inspection and testing?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Controls and evidence for the illustrative task
ERICPD and five-level positionIntervention and ownerVerification, failure and stop point
Eliminate / eliminationAt purchase or modification, the engineer moves lubrication, adjustment or condition-monitoring points outside the danger zone where practicable, so routine checks do not require guard removal or access beside moving parts.Verify the revised arrangement against all use and maintenance tasks. An awkward new access route or exposed linked drive means the intended risk reduction has not been demonstrated.
Reduce / substitution when replacing a hazard; otherwise engineering or administrative risk reductionThe engineer evaluates an alternative bearing or maintainable assembly that reduces intervention frequency or permits servicing from a protected location, subject to the machine specification and change assessment.Confirm compatibility, load, speed and protective-function effects with suitable technical information. A component substitution must not be assumed equivalent because it fits.
Isolate / engineeringFor the repair, authorised staff identify and isolate the conveyor and connected feeds, prevent reconnection, control stored energy and support parts that could move or fall using the machine-specific method.Verify the safe state before access. Unknown energy, a remaining live feed, pressure or an unstable part holds the repair; an emergency stop alone does not establish isolation.
Control / engineered and administrative measuresThe engineer defines a protected functional test with the required response and acceptance criteria, and the supervisor keeps everyone out of the danger zone. A necessary powered test uses a separately assessed specialist method.Record results and restore the safeguards and authorised operating mode. Failed stopping or restart behaviour, an exposed person or an unplanned powered test prevents hand-back.
PPE / PPESelect eye protection for particles and other task-specific protection where residual exposure remains. Consider entanglement and compatibility before selecting gloves around rotation; the repair method must control contact with movement.Inspect PPE and follow its maintenance and replacement arrangements. PPE cannot validate an interlock, hold a falling part or make an exposed conveyor safe.
Discipline / sustained engineering and administrative controlsManagers resource the inspection plan; supervisors enforce defect quarantine and named release; competent staff review recurring failures and changes to intervals or methods.Keep the defect, repair, protected test and hand-back evidence. A service receipt is not proof that each safety function works, and inspection intervals remain equipment- and risk-specific.

How can the ISO 45001 hierarchy of controls reduce machinery risks during maintenance, inspection and testing?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Controls and evidence for the illustrative task
ERICPD and five-level positionIntervention and ownerVerification, failure and stop point
Eliminate / eliminationAt purchase or modification, the engineer moves lubrication, adjustment or condition-monitoring points outside the danger zone where practicable, so routine checks do not require guard removal or access beside moving parts.Verify the revised arrangement against all use and maintenance tasks. An awkward new access route or exposed linked drive means the intended risk reduction has not been demonstrated.
Reduce / substitution when replacing a hazard; otherwise engineering or administrative risk reductionThe engineer evaluates an alternative bearing or maintainable assembly that reduces intervention frequency or permits servicing from a protected location, subject to the machine specification and change assessment.Confirm compatibility, load, speed and protective-function effects with suitable technical information. A component substitution must not be assumed equivalent because it fits.
Isolate / engineeringFor the repair, authorised staff identify and isolate the conveyor and connected feeds, prevent reconnection, control stored energy and support parts that could move or fall using the machine-specific method.Verify the safe state before access. Unknown energy, a remaining live feed, pressure or an unstable part holds the repair; an emergency stop alone does not establish isolation.
Control / engineered and administrative measuresThe engineer defines a protected functional test with the required response and acceptance criteria, and the supervisor keeps everyone out of the danger zone. A necessary powered test uses a separately assessed specialist method.Record results and restore the safeguards and authorised operating mode. Failed stopping or restart behaviour, an exposed person or an unplanned powered test prevents hand-back.
PPE / PPESelect eye protection for particles and other task-specific protection where residual exposure remains. Consider entanglement and compatibility before selecting gloves around rotation; the repair method must control contact with movement.Inspect PPE and follow its maintenance and replacement arrangements. PPE cannot validate an interlock, hold a falling part or make an exposed conveyor safe.
Discipline / sustained engineering and administrative controlsManagers resource the inspection plan; supervisors enforce defect quarantine and named release; competent staff review recurring failures and changes to intervals or methods.Keep the defect, repair, protected test and hand-back evidence. A service receipt is not proof that each safety function works, and inspection intervals remain equipment- and risk-specific.

The comparison is an original illustrative application of the general HSE hierarchy, not a machine-specific method, permit or design approval. The employer must choose measures for the actual work and jurisdiction. Apply the separate Northern Ireland legal route where relevant; the local assessment and competent technical decision govern release.

Sources: HSE hierarchy of controls; HSE maintenance of work equipment; HSE inspection of work equipment; HSENI PUWER 1999.

Applied case

A beam has been moved and a board added to create another picking shelf. Stock is ready to go on it, but no one can confirm the revised capacity or approval. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.

Compare your decision

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.

Lesson 10

A block stack is leaning into the aisle

Keep people and vehicle movements away from the affected area. Request a planned recovery and a suitable storage arrangement; do not pull cartons from the leaning stack.

Read the scene evidence

Palletised cartons have been stacked on packs that are visibly crushing. The stack leans towards the aisle, and there is no confirmed limit for this product and packaging.

Identify the condition separately from the exposed person and any possible outcome.

How the harm pathway develops

A leaning stack stands on damaged packaging with no verified stacking arrangement.

Palletised cartons have been stacked on packs that are visibly crushing. The stack leans towards the aisle, and there is no confirmed limit for this product and packaging.

How people can be exposed

People passing or taking stock from the stack can enter its collapse zone.

Possible harm

Falling loads could strike, crush or trap people and block the route.

Compare the work arrangements

ArrangementWhat changes exposure?
Uncontrolled arrangementPalletised cartons have been stacked on packs that are visibly crushing. The stack leans towards the aisle, and there is no confirmed limit for this product and packaging. The condition remains unresolved.
Protective responseKeep people and vehicle movements away from the affected area. Request a planned recovery and a suitable storage arrangement; do not pull cartons from the leaning stack.

Select controls by how they prevent harm

Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.

Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.

Control levelApplication to this case
EliminationRemove the need to stack these crushable packs directly on each other.
SubstitutionUse suitable load-bearing containers or designed racking selected for the product and handling method.
Engineering controlsProvide a stable base and designed support or containment for the assessed load configuration.
Administrative controlsSet product-specific stacking and inspection rules using supplier information; do not invent a universal safe height.
PPEUse assessed foot and other residual protection; PPE cannot hold a collapsing stack upright.

Verify, communicate and hand back

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.

How should workplace design and welfare be managed?

Design the layout and facilities for the people and work first, then provide, maintain, inspect, correct and review them as conditions change. The facilities owner checks routes, lighting, air and welfare in the real shift pattern, records defects and closes or diverts an unsafe area until repaired.

The strongest control is to design good conditions into the workplace before people start work. Once a workplace is operating, the management system has to keep facilities suitable through cleaning, maintenance, inspection, defect reporting, worker feedback and review after change.

Temporary work often fails because the welfare plan is created for the first day but not for the real project. As trades increase, weather changes, demolition exposes dust, or a site becomes more remote, the original toilets, washing, drying, lighting, routes and rest areas may no longer be enough.

StepWhat to defineEvidence or decision point
DesignLayout, access, welfare locations, workstations, routes, traffic separation, storage and emergency access.Site/premises layout reviewed before occupation or change. (HSE)
ProvideToilets, washing, drinking water, changing, rest, eating, ventilation, temperature control and lighting.Facilities match workforce size, work type, shifts and visitors. (HSE)
MaintainCleaning, servicing, repairs, waste removal, supplies, route condition and building fabric.Maintenance and cleaning schedules are active and resourced. (HSE)
InspectPlanned workplace inspections and supervisor checks of facilities, routes, lighting, temperature and housekeeping.Findings are recorded and prioritised by risk. (HSE)
ActDefects are fixed, temporary controls are applied and serious deficiencies are escalated.Action tracker shows close-out evidence. (HSE)
ReviewArrangements are reviewed after workforce growth, seasonal change, complaints, incidents, refurbishment or project phase change.Review record and revised welfare or layout plan. (HSE)

Completed welfare pre-start record

Fictional completed teaching record for the SHAREhub environment. Values and timings illustrate the decision; they are not site instructions or universal limits. HSE source HSE construction welfare guidance Source and scope

Peak users
Fictional refurbishment shift: 22 workers plus up to 4 visiting workers/drivers; afternoon overlap included. The site manager checks suitable provision against the actual users, not an invented toilet ratio.
Accessible route
The facilities lead and user representative walk protected route R-2 to the agreed accessible toilets, handwash and clean rest room before opening. Actual travel is recorded as about two minutes in this example; suitability and access still require the site assessment.
Clean/dirty boundary
Dusty PPE is removed/stored through the agreed hygiene arrangement. Eating is in the clean area; clean drinking water is reachable without crossing an active unloading bay.
Owner and checks
Facilities lead owns cleaning/restocking, with shift-start and use-driven checks; the supervisor reports failures immediately. Weekly review is an additional formal review.
Failure contingency
If the accessible facility or safe route fails, affected work is held until a suitable authorised alternative is verified and communicated. A vehicle is suitable for a break only where hygiene, space, temperature, contamination and work context support that assessment.

How should workplace design and welfare be assured?

Observe work as done, inspect a critical physical control, ask the user to explain a stop point, and trace one defect through correction and verification. Escalate repeated weak signals to the accountable manager rather than counting completed forms.

Assurance should include walk-throughs at different times, including shifts, poor weather, peak delivery periods and project phase changes. It should sample both direct employees and people who are easy to miss, such as cleaners, contractors, agency workers and drivers.

A strong assurance review asks whether welfare, layout and environment allow people to do the right thing easily. If the safe route is inconvenient, the toilet is too far away, or the rest area is dirty, the system will drift.

Inspect the workplace at shift start, peak occupancy and after a construction phase change. Ask a cleaner and visiting driver whether they can reach washing and toilets safely, test the route and lighting, and verify that ventilation and temperature problems are acted on. The manager reviews repeated closures and funds a lasting design fix.

Assurance sampleWhat good looks likeEscalate if
Welfare walk-throughFacilities are clean, stocked, accessible and adequate.Facilities are locked, dirty, distant or overloaded. (HSE)
Route and surface inspectionRoutes are clear, lit, maintained and segregated where needed.Defects repeat or temporary routes are uncontrolled. (HSE)
Worker conversationPeople know where facilities are and feel able to report defects.People avoid facilities or do not report concerns. (HSE)
Project/seasonal reviewFacilities change with work phase, weather and workforce size.Welfare remains static while the work changes. (HSE)
Contractor/driver samplingVisitors have clear welfare access and safe routes.Drivers wait without access or walk through vehicle areas. (HSE)
Leadership reviewWelfare defects and environment concerns are treated as risk issues.Issues are dismissed as comfort complaints. (HSE)

Applied case

Palletised cartons have been stacked on packs that are visibly crushing. The stack leans towards the aisle, and there is no confirmed limit for this product and packaging. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.

Compare your decision

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.

Lesson 11

A picking aisle loses its lighting

Hold the affected activity and protect a suitable alternative route. Report the fault for competent repair and assessment before the area is used again.

Read the scene evidence

An aisle light fails during the late shift. Stock shadows hide part of the floor and a pedestrian crossing, but the picking queue continues.

Identify the condition separately from the exposed person and any possible outcome.

How the harm pathway develops

Failed lighting and deep shadows prevent a clear view of the picking and travel area.

An aisle light fails during the late shift. Stock shadows hide part of the floor and a pedestrian crossing, but the picking queue continues.

How people can be exposed

People may enter a route or handle goods without seeing obstacles, edges or approaching vehicles clearly.

Possible harm

A missed obstacle or unseen movement could lead to a fall, collision or handling injury.

Compare the work arrangements

ArrangementWhat changes exposure?
Uncontrolled arrangementAn aisle light fails during the late shift. Stock shadows hide part of the floor and a pedestrian crossing, but the picking queue continues. The condition remains unresolved.
Protective responseHold the affected activity and protect a suitable alternative route. Report the fault for competent repair and assessment before the area is used again.

Select controls by how they prevent harm

Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.

Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.

Control levelApplication to this case
EliminationMove the affected task to an already verified, suitably lit location while the lighting defect is corrected.
SubstitutionConsider a suitable storage or task layout that reduces shadows and visibility demands.
Engineering controlsProvide suitable maintained lighting positioned for the actual task, including glare and obstruction checks.
Administrative controlsInspect under real shift conditions and control temporary lighting and repair access; a phone torch is not a route assessment.
PPEUse assessed residual protection; high-visibility clothing cannot provide missing illumination.

Verify, communicate and hand back

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.

How does the working environment affect health and safety?

Ventilation, temperature, lighting, space and cleanliness shape both immediate safety and long-term health.

A workplace can be legally and practically unsafe even where no machine, chemical or vehicle is involved. Poor ventilation can worsen exposure; poor lighting can lead to errors and falls; cramped space can force awkward posture; heat can increase fatigue; cold can affect dexterity; and poor cleanliness can spread contamination. HSE.

The environment should be reviewed whenever the work changes. Introducing new equipment, more workers, new cleaning chemicals, temporary screens, PPE, outdoor work or shift working can change the risk profile.

Environment factorRisk routeControl focus
VentilationStale air, fumes, dust, vapour, heat or biological aerosol build-up.Adequate fresh air, local extraction where needed, maintenance and worker feedback. (HSE)
TemperatureHeat stress, cold stress, fatigue, discomfort, poor concentration or loss of dexterity.Reasonable temperature, local controls, breaks, clothing/PPE review and seasonal planning. (HSE)
LightingFalls, vehicle conflict, errors, poor inspection or emergency-route confusion.Suitable lux levels, emergency lighting, glare control and inspection. (HSE)
SpaceCrowding, poor posture, blocked access, route conflict and evacuation issues.Workstation design, storage control, clear routes and occupancy review. (HSE)
CleanlinessContamination, slips, pests, poor morale and fire load.Cleaning plan, waste control, welfare separation and inspection. (HSE)
Noise and communicationMissed warnings, fatigue, poor coordination and stress.Noise control, communication methods, alarms and supervision. (HSE)

How should workplace design and welfare be assured?

Observe work as done, inspect a critical physical control, ask the user to explain a stop point, and trace one defect through correction and verification. Escalate repeated weak signals to the accountable manager rather than counting completed forms.

Assurance should include walk-throughs at different times, including shifts, poor weather, peak delivery periods and project phase changes. It should sample both direct employees and people who are easy to miss, such as cleaners, contractors, agency workers and drivers.

A strong assurance review asks whether welfare, layout and environment allow people to do the right thing easily. If the safe route is inconvenient, the toilet is too far away, or the rest area is dirty, the system will drift.

Inspect the workplace at shift start, peak occupancy and after a construction phase change. Ask a cleaner and visiting driver whether they can reach washing and toilets safely, test the route and lighting, and verify that ventilation and temperature problems are acted on. The manager reviews repeated closures and funds a lasting design fix.

Assurance sampleWhat good looks likeEscalate if
Welfare walk-throughFacilities are clean, stocked, accessible and adequate.Facilities are locked, dirty, distant or overloaded. (HSE)
Route and surface inspectionRoutes are clear, lit, maintained and segregated where needed.Defects repeat or temporary routes are uncontrolled. (HSE)
Worker conversationPeople know where facilities are and feel able to report defects.People avoid facilities or do not report concerns. (HSE)
Project/seasonal reviewFacilities change with work phase, weather and workforce size.Welfare remains static while the work changes. (HSE)
Contractor/driver samplingVisitors have clear welfare access and safe routes.Drivers wait without access or walk through vehicle areas. (HSE)
Leadership reviewWelfare defects and environment concerns are treated as risk issues.Issues are dismissed as comfort complaints. (HSE)

Applied case

An aisle light fails during the late shift. Stock shadows hide part of the floor and a pedestrian crossing, but the picking queue continues. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.

Compare your decision

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.

Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.

Lesson 12

Shift handover: connect the hazards

Defend the stopping condition and the evidence needed for release.

Reconstruct the whole task

A damaged upright has been marked with tape. A heavy pallet is waiting below a changed beam position, while a picker considers climbing the rack to reach an overhang.

The damaged upright has been repainted and the floor cleared, but no competent assessment addresses the impact or the altered configuration.

Keep the affected storage restricted until the damage and configuration have been assessed and an authorised safe arrangement is verified.

Build an evidence-led handover

ItemWhat the receiver needs
Task and locationRacking, pallets and high-bay storage — identify the affected people and boundaries.
Actual conditionThe damaged upright has been repainted and the floor cleared, but no competent assessment addresses the impact or the altered configuration.
Control and current restrictionKeep the affected storage restricted until the damage and configuration have been assessed and an authorised safe arrangement is verified.
Verification and ownerName the responsible role and the task-specific evidence. Keep unresolved matters open.

Use the documents as working tools

Map the task, people, exposure pathway, existing controls, missing evidence and review trigger. Use the fictional course case.

Prepare a five-minute task briefing. Ask a scenario question and check understanding, rather than relying on an attendance signature.

Find who owns the control, who can authorise release and how a worker escalates a defect. Check the actual local arrangements.

Compare a claim with an observation, a relevant record and a competent explanation. Record open actions and verify closure.

How does the working environment affect health and safety?

Ventilation, temperature, lighting, space and cleanliness shape both immediate safety and long-term health.

A workplace can be legally and practically unsafe even where no machine, chemical or vehicle is involved. Poor ventilation can worsen exposure; poor lighting can lead to errors and falls; cramped space can force awkward posture; heat can increase fatigue; cold can affect dexterity; and poor cleanliness can spread contamination. HSE.

The environment should be reviewed whenever the work changes. Introducing new equipment, more workers, new cleaning chemicals, temporary screens, PPE, outdoor work or shift working can change the risk profile.

Environment factorRisk routeControl focus
VentilationStale air, fumes, dust, vapour, heat or biological aerosol build-up.Adequate fresh air, local extraction where needed, maintenance and worker feedback. (HSE)
TemperatureHeat stress, cold stress, fatigue, discomfort, poor concentration or loss of dexterity.Reasonable temperature, local controls, breaks, clothing/PPE review and seasonal planning. (HSE)
LightingFalls, vehicle conflict, errors, poor inspection or emergency-route confusion.Suitable lux levels, emergency lighting, glare control and inspection. (HSE)
SpaceCrowding, poor posture, blocked access, route conflict and evacuation issues.Workstation design, storage control, clear routes and occupancy review. (HSE)
CleanlinessContamination, slips, pests, poor morale and fire load.Cleaning plan, waste control, welfare separation and inspection. (HSE)
Noise and communicationMissed warnings, fatigue, poor coordination and stress.Noise control, communication methods, alarms and supervision. (HSE)

Applied case

The damaged upright has been repainted and the floor cleared, but no competent assessment addresses the impact or the altered configuration.

Compare your decision

Keep the affected storage restricted until the damage and configuration have been assessed and an authorised safe arrangement is verified.

Keep the affected storage restricted until the damage and configuration have been assessed and an authorised safe arrangement is verified.

Lesson 13

Your workplace transfer challenge

Turn one lesson into a bounded check with an owner and a review trigger.

Prepare a useful task briefing

Connect storage design, condition, loading and access.

Use the printable course workbook to describe one fictional task. State who could be exposed, the harmful mechanism, a higher-level control, the immediate restriction and the evidence needed to close the action.

Test understanding and inspect the arrangement

Protect the affected area and obtain competent inspection and release.

Ask the team what they would do if the control failed. Compare their answer with the actual arrangements and the source teaching. Check both what people understand and whether the physical control works.

Keep learning and operational authority clear

Independent warehouse awareness and decision practice for a GB baseline; check corresponding Northern Ireland duties and site arrangements. Completion is not practical competence, a licence or authority for specialist work.

The workbook is a practice document. Use the authorised workplace system for real risk assessments, permits, defect reports and audits. Video demonstrations can be added later; no missing video is required to complete this course.

Applied case

You are asked to prepare a toolbox talk and a check for the next shift. The current document says only: be more careful.

Compare your decision

Identify the task, responsible role, required evidence, restriction and trigger for review.

A useful action connects the work to its owner, evidence and a clear decision boundary.