Safety performance indicators that support decisions · detailed source study
Optional reference study from the SHAREhub topic pages and selected source records used for this course. The core learning-time estimate excludes this extended reference.
What makes a measure key?
What makes a measure key?
Source: kpi-s--key-facts
A measure is key when it relates to a material risk or objective, has a dependable definition, and leads to a decision. A measure is key when it relates to a material risk or objective, has a dependable definition, and leads to a decision. A key performance indicator (KPI) is a selected measure that helps people judge whether important health and safety controls work and what decision to make next. Apply it: Which part of this plan would you check at the workface before authorising the task? A key performance indicator (KPI) is a selected measure that helps people judge whether important health and safety controls work and what decision to make next.
A balanced set combines evidence of critical-control health, worker reports, investigations and actual harm; counts or percentages alone can hide failure. Percentage of critical controls verified as effective, with high-risk defects closed and rechecked. Apply it: What evidence would show that the change improves this task, rather than only completing a record? Number of inspections completed: It counts activity but not whether important controls were effective. Evidence / response: Percentage of critical controls verified as effective, with high-risk defects closed and rechecked. Zero accidents: It may reflect luck, under-reporting or low exposure rather than good control. Evidence / response: Near-miss reporting quality, repeat-event themes, action closure and control-health trend.
Apply it: At which point would you hold this example, and what evidence would allow it to proceed? Only lagging indicators: The dashboard relies on outcomes or failures without checking preventive activities; a barrier failure or near miss can be a lagging result even when nobody is injured. Perfect dashboards: Under-reporting or weak challenge may exist. Huge number of measures: Signal is buried in noise. Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby? Live-area contractor entry: In the illustrative the process operator task, use remote inspection or complete fabrication outside the live area where the information and plant design allow; then no contractor crosses the live permit boundary.
Live-area entry: Trial a lower-energy or off-site method that still proves the required condition; do not call a remote image equivalent to a physical test without technical acceptance. Live-area entry: Before unavoidable entry, prove physical isolation and the relevant barrier or interlock at the boundary; a dashboard or induction record cannot create separation. Live-area entry: Use a permit, boundary walk-through and task demonstration, then sample contractor understanding in the field. Live-area entry: Select any residual protection for the identified exposure and verify compatibility and fit; it does not replace isolation or a correct permit. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.
Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk? Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status. Apply it: Which official source and full-topic section will you use to resolve the next decision? Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.
A measure is key when it relates to a material risk or objective, has a dependable definition, and leads to a decision. A measure is key when it relates to a material risk or objective, has a dependable definition, and leads to a decision. A key performance indicator (KPI) is a selected measure that helps people judge whether important health and safety controls work and what decision to make next. Apply it: Which part of this plan would you check at the workface before authorising the task? Use the evidence to improve the actual work arrangement. A key performance indicator (KPI) is a selected measure that helps people judge whether important health and safety controls work and what decision to make next.
A balanced set combines evidence of critical-control health, worker reports, investigations and actual harm; counts or percentages alone can hide failure. Percentage of critical controls verified as effective, with high-risk defects closed and rechecked. Apply it: What evidence would show that the change improves this task, rather than only completing a record? Fictional example: a practical application of the existing topic lesson. Number of inspections completed: It counts activity but not whether important controls were effective. Evidence / response: Percentage of critical controls verified as effective, with high-risk defects closed and rechecked. Zero accidents: It may reflect luck, under-reporting or low exposure rather than good control. Evidence / response: Near-miss reporting quality, repeat-event themes, action closure and control-health trend.
Apply it: At which point would you hold this example, and what evidence would allow it to proceed? Connect the task, the route to the person and the control that can fail. Only lagging indicators: The dashboard relies on outcomes or failures without checking preventive activities; a barrier failure or near miss can be a lagging result even when nobody is injured. Perfect dashboards: Under-reporting or weak challenge may exist. Huge number of measures: Signal is buried in noise. Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby? Start with the stronger practicable options and verify their effect.
Live-area contractor entry: In the illustrative the process operator task, use remote inspection or complete fabrication outside the live area where the information and plant design allow; then no contractor crosses the live permit boundary. Live-area entry: Trial a lower-energy or off-site method that still proves the required condition; do not call a remote image equivalent to a physical test without technical acceptance. Live-area entry: Before unavoidable entry, prove physical isolation and the relevant barrier or interlock at the boundary; a dashboard or induction record cannot create separation. Live-area entry: Use a permit, boundary walk-through and task demonstration, then sample contractor understanding in the field.
Live-area entry: Select any residual protection for the identified exposure and verify compatibility and fit; it does not replace isolation or a correct permit. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged. Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk? Follow the official sources below and retain the task-specific evidence. Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status.
Apply it: Which official source and full-topic section will you use to resolve the next decision? Simplified learning guide. Use the full topic and the actual work arrangements; existing technical-review and approval statuses still apply. Workplace scenarios labelled fictional are illustrative examples. Start with the credible harm and the control that prevents it. Choose a signal near that control, decide what a concerning result looks like, and name the person who can change work. One number rarely proves control: sample records, observe the task and ask workers whether the reported result matches reality. Sources: HSE HSG65: Managing for health and safety, HSE HSG254: Developing process safety indicators.
What is a KPI in plain English?
What is a KPI in plain English?
Source: kpi-s--plain-english
A key performance indicator is a selected measure used to judge whether important controls and improvement actions are working. An injury total reports harm after it happened. An isolation verification measure asks whether a critical control was actually used before maintenance. Both matter. The first may miss a low-frequency catastrophic risk; the second can be gamed if the check is superficial. Pair them with observations, defects, worker reports and evidence that corrective action worked. Sources: HSE HSG65: Managing for health and safety, HSE HSG254: Developing process safety indicators. A metric is a measure, such as a count, rate, percentage or duration; a KPI is selected because it informs an important decision. A target is the intended level.
A threshold is the point that triggers review, a hold or escalation. The indicator is useful only when its owner can explain the response and the evidence behind the number. The HSE guides cited for KPI methods are GB regulator guidance. The methods may help NI workplaces, but NI legal duties and incident reporting must be checked through the separate NI sources below.
Why do KPIs matter for risk management?
Source: kpi-s--why-matter
They let an organisation detect control drift before people are harmed and test whether its response changes the conditions of work. For example, rising overdue inspections on safety-critical equipment should lead to a review of the affected equipment, maintenance resource and any required hold. A falling near-miss count after workers were blamed may indicate lost trust, not improved safety. Ask why the trend changed before praising or penalising anyone. Sources: HSE HSG65: Managing for health and safety, HSENI: Co-operation and monitoring safe working.
Which types of indicator belong together?
Source: kpi-s--indicator-types
Combine lagging harm, leading prevention, control-health, exposure, learning and worker-feedback signals around the risk. For a vehicle interface, injury reports show past harm; segregation inspections, barrier defects, traffic observations and worker reports show whether prevention still works. For hazardous substances, the right measures may cover exposure control, maintenance, valid sampling, surveillance where required and action on findings. Do not treat an activity count as proof of effectiveness. Sources: HSE HSG65: Managing for health and safety, HSE HSG254: Developing process safety indicators.
How is a useful KPI designed?
Source: kpi-s--good-kpi-design
Define the risk, decision, owner, numerator, denominator, period, source, threshold and validation method before putting a number on a dashboard. Write inclusion and exclusion rules in a KPI dictionary. Test the calculation against examples, contractor and shift coverage, missing data, duplicate records and changed operations. Ask workers whether the chosen measure tracks the real task. A target should improve a control without discouraging honest reporting. Sources: HSE HSG65: Managing for health and safety, HSENI: Co-operation and monitoring safe working. Illustrative decision: nine of ten vehicle–pedestrian barriers due for verification are recorded as effective, giving 90%. If the unchecked barrier protects a live crossing, the supervisor does not release that crossing because the percentage looks high.
They separate people and vehicles, verify or restore the barrier, record the exception and test whether the dashboard exposed it promptly. The measure must identify which control failed, not just the average. Sources: HSE HSG65, HSE HSG254 process-safety indicator method. For the physical separation decision, see HSE separating pedestrians and vehicles (GB) and HSENI Drive Danger Out (NI practical guidance).
What is a bad KPI compared with a useful KPI?
Source: kpi-s--bad-useful
Useful KPIs show whether important controls are working; bad KPIs often count activity without proving risk reduction. A bad KPI is not always a useless number. It may still tell part of the story, but it becomes weak when leaders treat it as proof of safety. For example, completed inspections show that checks happened; they do not prove that critical controls were present, defects were risk-ranked, actions were owned or repeat problems were challenged. A useful KPI is closer to the risk. It asks whether the thing that prevents serious harm was verified, whether workers understood the control in the task, whether corrective actions changed behaviour and whether the organisation learned.
This is why good dashboards combine quantity with quality, field verification and evidence of follow-through.
What should a practical dashboard show?
Source: kpi-s--dashboard
A short dashboard shows the risk, current control-health signal, trend, data quality, threshold, owner, decision and follow-up evidence. Separate immediate exceptions from monthly trends. A failed critical barrier may need a same-shift hold even when the monthly percentage is green. Show the denominator and sample size beside a percentage; show overdue high-consequence actions separately from routine actions. Include a narrative about changed work or data gaps. Sources: HSE HSG65: Managing for health and safety, HSE HSG254: Developing process safety indicators.
Which calculations are useful?
Source: kpi-s--formulas
Rates can compare periods with different exposure, but their definitions and limits must travel with the result. For an on-time control-check rate, divide checks due in the reporting period that have a valid result completed by their individual deadlines by all checks due in that period, then multiply by 100. Fix the reporting cut-off and retain each due date and actual completion time. If all 49 of 50 due checks had valid results completed on time, the rate is 98%; the remaining check still needs a risk decision. Show late completions and missing results separately. Old overdue checks are outside this period’s on-time numerator; a late completion must never be backdated into success.
Injury frequency rates also depend on hours, inclusion rules and a chosen multiplier. A small number of events can swing a rate sharply, so show the count and context too. Sources: HSE HSG65: Managing for health and safety. Fictional exposure-rate example: in one stated calendar year, one work-related injury causing more than seven days’ inability to do normal duties occurred among the employees and contractors included in 100,000 recorded hours worked. Using a declared multiplier of 1,000,000: 1 ÷ 100,000 × 1,000,000 = 10 qualifying injuries per million hours worked. The injury category, period and employee/contractor scope must match the hours; this is a rate per hours, not per workers, and the multiplier is a reporting choice rather than a universal target.
One event cannot establish a reliable organisation-wide trend. Nor can the worked example’s five deliberately selected high-risk contractors represent the whole organisation. Show counts, hours, sampling method and uncertainty; incompatible scopes or exposure cannot support simple league tables. Act on critical-control failures despite statistical uncertainty.
How can KPI results be calculated without hiding missing evidence?
How can KPI results be calculated without hiding missing evidence?
Source: kpi-s--reconcile-results
Show both performance and evidence coverage. Separate passed, failed and missing records; a zero denominator has no percentage, and a combined result should retain the site or shift results needed to make a risk decision. Decide what question each percentage answers before collecting it. A pass rate, evidence coverage and completion rate can use different denominators even when drawn from the same log. These original teaching calculations make that distinction visible; they are not regulator-set targets. HSE’s monitoring approach connects reports to control effectiveness and action. Sources: HSE: Check performance, HSE HSG65: Managing for health and safety. Fictional log: 100 checks are due. There are 80 valid completed records: 72 pass and eight fail. The remaining 20 due checks have no valid result.
Keep those three groups separate. A missing record does not prove a control failed, but it cannot provide evidence that the control passed. On a narrow screen, scroll this example table sideways to read all columns. The combined-site result is a second example with its own counts. The simple average of 98% and 50% is 74%; that gives the sites equal weight and answers a different question. Use 990 divided by 1,020 only when the underlying check definitions and periods are compatible. Neither aggregation removes the need to investigate site B or any failed critical control. For zero activity, distinguish “nothing was due” from “the data is missing”.
If work occurred but the due count is unknown, show an unavailable result and obtain the missing evidence. Do not label it not applicable or green. Keep original records and a dated correction explaining any duplicate removal or denominator change so the revised result remains traceable. Sources: HSE HSG65: Managing for health and safety. Management sets the response rule from the actual risk and control standard. HSG254 discusses tolerances and follow-up for process safety; a dashboard tolerance does not grant permission to operate with a failed critical barrier. A trend can go to the routine review while a serious control exception goes to the responsible manager immediately. Sources: HSE HSG254: Developing process safety indicators, HSE: Check performance.
Learning check: explain what 90%, 80% and 72% each mean, identify the eight known failures and the 20 unknown results, and name the person who makes the next work decision. A correct percentage without that explanation is incomplete assurance.
Who checks KPI evidence and acts on it?
Source: kpi-s--assurance-review
The work owner needs to act on control failures, a competent reviewer should challenge the quality of the measure, and management should test whether corrective action worked. Keep these responsibilities clear even in a small organisation. A supervisor checks the actual guard, isolation or permit boundary and stops unsafe work. A safety or technical adviser reviews definitions, sampling and recurring exceptions. Management reviews the evidence, assigns resources and verifies closure. HSE places monitoring and review within its Plan, Do, Check, Act approach. Source: HSE HSG65 managing for health and safety. An independent check can provide additional challenge, but a green dashboard cannot overrule a failed critical control. Record who owns the control, who verified the data and who authorised restart after a failed barrier.
Source: HSE HSG65 managing for health and safety.
What can make a KPI misleading?
Source: kpi-s--data-quality
Missing or duplicate records, inconsistent definitions, changing denominators, biased samples and incentives to hide reports can make a reassuring figure false. Compare source records with dashboard totals. Sample different sites, shifts and contractors; check whether closed actions changed field conditions. A sudden drop in hazard reports may reflect fear or a broken reporting route. State uncertainty rather than manufacturing a precise trend from incomplete data. Sources: HSE HSG65: Managing for health and safety, HSENI: Co-operation and monitoring safe working.
How can a good-looking result conceal risk?
Source: kpi-s--worked-example
A 98% contractor induction result can hide a serious understanding gap if attendance is counted as competence. Suppose 49 of 50 contractors signed in, so the induction KPI reads 98%. A supervisor then samples five high-risk contractors: two cannot explain permit boundaries and one cannot describe the site alarm. The supervisor holds the affected work, briefs the people involved and verifies understanding at the point of work; the one missed induction is traced as well. The 98% headline remains in the record but is no longer described as assurance. Sources: HSE HSG65: Managing for health and safety, HSENI: Co-operation and monitoring safe working. The contract manager owns a revised measure: high-risk contractors who pass a task and emergency understanding check, divided by high-risk contractors sampled.
The sample, exclusions and assessor are recorded. Any failure on a critical permit boundary triggers an immediate hold regardless of the monthly percentage. The manager reviews the induction content, language, supervision and onboarding process; a later field sample closes the action only if work is correct. Sources: HSE HSG65: Managing for health and safety.
How should a KPI follow the control hierarchy?
Source: kpi-s--hierarchy
Measure whether the strongest feasible control works on the real hazard, then make a failed barrier change the work decision. A high completion percentage cannot compensate for an unsafe entry. For the illustrative contractor permit-boundary example, the hazard is entry to a live high-energy area, not the KPI itself. HSE places elimination and substitution ahead of engineering and administrative controls, with PPE for residual risk. Measure whether the chosen barrier works in the field, and hold work when it fails. Source: HSE managing risk using PPE. For the separate Crownway proof-test example, a failed critical barrier is an immediate hold even if the monthly KPI is green.
The owner first asks whether the hazardous task can be removed or changed, then verifies engineered protection before relying on permit conditions or residual PPE. Record the failed test, action owner, independent field recheck and restart decision; do not count administrative closure as restored protection. Sources: HSE HSG254: Developing process safety indicators.
How does useful measurement change work?
Source: kpi-s--poor-good
A useful KPI leads to a verified decision, while a weak one rewards easy counts or hides exceptions. Counting 100 inspections says little if none tested a critical control. A better review asks which controls were sampled, what failed, who held or changed the task, whether workers agreed that the fix worked and whether the same defect returned. Leaders should question apparently perfect figures where independent checks or worker reports tell a different story. Sources: HSE HSG65: Managing for health and safety.
What evidence shows KPIs are managed well?
What evidence shows KPIs are managed well?
Source: kpi-s--evidence
Evidence should show that KPIs are defined, reviewed, challenged and acted on. Evidence should be read as a chain rather than a filing exercise. A single record rarely proves good management on its own; stronger assurance comes from matching records, observations, interviews, trends and verified action closure.
Which duties apply in Great Britain and Northern Ireland?
Source: kpi-s--legal
Neither jurisdiction prescribes a universal KPI dashboard. Duties to assess and manage work risks, monitor arrangements and report specified events must be applied under the law for the workplace. In Great Britain, the Health and Safety at Work etc. Act 1974 and Management Regulations 1999 provide the general and management framework. In Northern Ireland, use the Health and Safety at Work (NI) Order 1978 and Management Regulations (NI) 2000. A chosen KPI is evidence for management, not a substitute for the actual assessment or control. Sources: Health and Safety at Work etc. Act 1974, Management of Health and Safety at Work Regulations 1999, Health and Safety at Work (Northern Ireland) Order 1978, Management of Health and Safety at Work Regulations (NI) 2000.
RIDDOR data must remain jurisdiction-specific. GB uses the 2013 reporting regulations and an over-seven-day injury reporting route; NI uses the 1997 regulations and an over-three-day route. The responsible person should check current categories and incident facts with the relevant regulator rather than infer reportability from a dashboard label. Sources: HSE: RIDDOR reportable incident types, HSENI: Report an incident.
How would Crownway Fuels Ltd use a risk-based dashboard?
Source: kpi-s--business-example
The fictional operator should measure the barriers that prevent loss of containment and other major harm, alongside occupational health, contractor and everyday safety outcomes. Its monthly board view reports critical maintenance overdue, proof-test failures, permit deviations, high-potential events and closure effectiveness. A separate operational view lets supervisors act on a failed valve test or permit boundary immediately. No low injury rate can compensate for a failed major-hazard barrier. Sources: HSE HSG254: Developing process safety indicators, HSE HSG65: Managing for health and safety. Crownway chooses one owner for each measure and records scope, calculation, source and escalation threshold. When a proof test fails, operations takes the affected system to its safe state under the site procedure, maintenance investigates, and a competent person verifies the repair.
The board later sees the cause, resources used and effectiveness check, not simply a green percentage. Sources: HSE HSG254: Developing process safety indicators.
Who needs to learn and demonstrate KPI decisions?
Source: kpi-s--training
Competence means being able to define, validate, question and act on the measure appropriate to the role, not merely attending dashboard training. A worker should know how to report a failed control without being judged by an injury target. Supervisors must distinguish a missing record from a failed barrier and know when to hold work. Analysts need to reconcile source data and challenge denominator changes. Managers and directors must decide resources and verify closure. Assess these decisions using actual examples and retain evidence of performance. Sources: HSE HSG65: Managing for health and safety, HSENI: Co-operation and monitoring safe working.
How should a learner explain performance monitoring?
Source: kpi-s--study
Link each proposed measure to a risk, a control, the quality of the evidence and the decision that follows. In an assessment, distinguish lagging harm from leading and control-health evidence, show one numerator and denominator, then explain an exception and the owner’s response. Explain why a zero-injury month cannot prove the system safe. HSG65 frames monitoring and review within Plan–Do–Check–Act. Sources: HSE HSG65: Managing for health and safety.
What can a health and safety management system add?
Source: kpi-s--iso
A management system can use KPIs to test whether important controls work and whether corrective decisions improve the work. Certification alone does not prove legal compliance. HSE describes ISO 45001 as an optional health and safety management standard. Its guidance asks organisations to tailor arrangements to their size and risk, and says inspectors use a range of evidence and observations. Use defined measures, worker feedback, field verification and recorded management decisions; check any exact standard requirement against authorised text. Source: HSE health and safety management systems.
What warning signs show KPIs are not adding value?
Source: kpi-s--warning-signs
Warning signs appear when numbers are collected but not trusted, understood or acted on. Warning signs are included because failure usually appears before a serious event. Treat these points as prompts for inspection, audit, supervision and management review rather than as simple compliance statements.
How can the hierarchy of controls verify actual conveyor isolation behind a safety-performance KPI?
Source: kpi-s--kpi-s-hierarchy-of-controls
How can the hierarchy of controls verify actual conveyor isolation behind a safety-performance KPI?
An isolation KPI shows completed paperwork for conveyor work. Verify energy control at the real maintenance boundary and make a failed check stop the task; the percentage is evidence, not the safeguard. Control level Control for this activity Owner and verification Stop / restart decision Eliminate Move routine checks and lubrication points outside the guard so opening it is unnecessary. Basis: Official task guidance: www.hse.gov.uk Machine owner confirms that inspection and lubrication can be completed outside the guarded area, including foreseeable faults and cleaning. If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls. Reduce, including substitution Use a manufacturer-approved external inspection method or safely replaceable module where this reduces access to dangerous parts.
Treat the design as an engineering control and retain isolation for intrusive work. Competent machine owner validates the external method or removable module against the manufacturer’s instructions; identify any work that still requires isolation. Reject an alternative if its performance is unproved or its new hazards are unresolved. Isolate Stop and securely isolate all relevant energy sources; verify isolation and restrain parts or loads that could move. Supervisor checks the actual boundary, affected people and connected work; verify separation or isolation before allowing access. Hold or stop for uncertain isolation, retained motion, unsupported load or failed interlock. Control: physical safeguards Restore suitable guards and interlocks after the repair and test the safety function before production release.
Competent equipment/process owner checks energy sources, stored energy, guard fixings and interlock response. Hold or stop for uncertain isolation, retained motion, unsupported load or failed interlock. Control: work method and response Identify the isolation boundary, affected contractors and restart owner; control any authorised diagnostic mode separately. Supervisor confirms the work limits, competent cover, communication and stop/restart authority with the people doing this activity. Hold work when the agreed limits, competent cover or effective communication cannot be maintained. PPE Select task-assessed eye, hand and foot protection. Gloves must not create an entanglement risk near moving parts. Assessor confirms whether personal protection is needed and checks suitability, condition, compatibility and any required fit evidence.
Do not use unsuitable protection or rely on PPE to continue after an essential source control fails. Discipline Record guard defects, isolation removal and functional tests; do not close the job on paperwork alone. Release only after maintenance and operations agree the guarded restart. Retain verification and unresolved restrictions at handover. Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner.
Where does active and reactive monitoring apply?
Where does active and reactive monitoring apply?
Source: active-and-reactive-monitoring--scope
This page helps workplaces choose checks before harm and learn after failure; it is not a substitute for a site risk assessment or the correct GB or NI law. Use it for risk-control inspections, tests, exposure checks, incident and near-miss learning, health signals, action tracking and management review. It covers workers, contractors, visitors and members of the public where work may affect them. A completed form, low injury rate or ISO certificate alone does not prove that a control is effective. Identify the actual hazard, task, location, people and jurisdiction before choosing measures. Choose a monitoring frequency and method from the actual risk, critical controls, exposure and change history. Escalate a failed safeguard even when the injury-rate trend looks favourable.
Monitoring itself is a management method. Test the physical, health or organisational control in real work, then use the findings to change the task and verify the result.
Make each indicator lead to a control decision
Source: active-and-reactive-monitoring--review-start
Start with a decision, then choose a measure that can support it. State the numerator, denominator, exposure period and source. A planned inspection is active monitoring; an unexpected defect or symptom report is reactive. Neither label alone tells you whether a measure leads or lags a particular outcome. Choose monitoring that answers a real control question. Planned checks can identify deterioration before an event; reactive monitoring examines what happened and why. Both should lead to practical action, feedback and verification rather than a dashboard alone. Apply it: Choose one important control and say what evidence would show it is working. An injury count can miss low-frequency, high-consequence failures and under-reporting. Read it beside meaningful control checks and the experience of workers.
Compare like-for-like tasks and periods; a higher reporting rate can reflect better reporting rather than worsening safety. Apply it: Which weak control would your current dashboard fail to reveal? The supervisor records the obstruction and acts under the site's fire and opening arrangements; a critical failure is not averaged away by a high checklist score. The manager addresses why deliveries repeatedly block the route, then verifies the change at a representative delivery time. Apply it: What restriction or decision is needed before the affected area can open? Monitoring adds value when it reveals what could happen if a control is needed. The consequence of a blocked escape route matters even where no injury has yet occurred.
A near miss or repeated defect is a reason to investigate the arrangements, not wait for harm. Apply it: Record the immediate control and the underlying arrangement that needs to change. Solve the storage and delivery problem at source and assess the effect on the whole layout. The hierarchy is a way to challenge the action, not a requirement to invent PPE for every hazard. Follow-up checks should show that the route remains usable when deliveries actually occur. Apply it: Can the proposed change prevent recurrence without relying only on memory? Use the full page to choose indicators, distinguish monitoring from auditing and decide how findings reach management review. The checklist is an example for recording observations, not a certificate of safety.
Check the full legal guidance where a statutory reporting question arises. Apply it: Select one recurring finding and follow it through to evidence that the control is effective. Keep one card or the full set for social sharing, team briefings and learning. Every PDF contains one card per page and links back to its full topic. Use proactive checks and incident learning together. Choose monitoring that answers a real control question. Planned checks can identify deterioration before an event; reactive monitoring examines what happened and why. Both should lead to practical action, feedback and verification rather than a dashboard alone. Apply it: Choose one important control and say what evidence would show it is working. Combine outcomes with evidence about the controls themselves.
An injury count can miss low-frequency, high-consequence failures and under-reporting. Read it beside meaningful control checks and the experience of workers. Compare like-for-like tasks and periods; a higher reporting rate can reflect better reporting rather than worsening safety. Apply it: Which weak control would your current dashboard fail to reveal? Fictional example: a leisure-centre supervisor makes a control decision. The supervisor records the obstruction and acts under the site's fire and opening arrangements; a critical failure is not averaged away by a high checklist score. The manager addresses why deliveries repeatedly block the route, then verifies the change at a representative delivery time. Apply it: What restriction or decision is needed before the affected area can open?
Connect the reported defect to the event it could worsen. Monitoring adds value when it reveals what could happen if a control is needed. The consequence of a blocked escape route matters even where no injury has yet occurred. A near miss or repeated defect is a reason to investigate the arrangements, not wait for harm. Apply it: Record the immediate control and the underlying arrangement that needs to change. A route-obstruction example: act beyond a reminder. Solve the storage and delivery problem at source and assess the effect on the whole layout. The hierarchy is a way to challenge the action, not a requirement to invent PPE for every hazard. Follow-up checks should show that the route remains usable when deliveries actually occur.
Apply it: Can the proposed change prevent recurrence without relying only on memory? Find it. Protect people. Improve the arrangement. Verify it. Use the full page to choose indicators, distinguish monitoring from auditing and decide how findings reach management review. The checklist is an example for recording observations, not a certificate of safety. Check the full legal guidance where a statutory reporting question arises. Apply it: Select one recurring finding and follow it through to evidence that the control is effective. Simplified learning guide. Use the full topic and the actual work arrangements; existing technical-review and approval statuses still apply. Workplace scenarios labelled fictional are illustrative examples. A low event count is weak reassurance if reporting is discouraged or contractor/night-shift work is missing.
Join control-condition checks with reports of failure, allocate an owner and test the action under the demand that originally exposed the weakness. Illustrative example. Several cleaners report skin problems while routine inspections record that gloves are available. Decision. Investigate the actual product, wet work and glove use; change the control and check its use, rather than increase glove-stock counts. Evidence to check. Compare affected tasks and reporting periods; observe the method across relevant shifts and protect individual health details. Hold or escalation point. Do not close the action from PPE availability or falling reports alone. Follow-up. Review task exposure and worker feedback after the change; preserve enough denominator and shift context to interpret the result.
Open Monitoring decision and action register Read with: HSE HSG65 Managing for health and safety · HSE How to manage health and safety · HSE HSG245 Investigating accidents and incidents (2004 edition; verify current HSE listing).
Where this fits in Plan, Do, Check, Act
Where this fits in Plan, Do, Check, Act
Source: active-and-reactive-monitoring--pdca-leadership-cycle
Active and reactive information belong in Check, but the loop is incomplete until someone acts on the findings and revises the next plan. First-line checks, specialist support, independent internal audit and external assurance have different roles; a good daily check does not replace them all. ISO 45001:2018 + Amd 1:2024 Understand the activities and people affected, identify hazards, assess risks and opportunities, establish applicable requirements and set owned OH&S objectives. Risk profiling informs planning as well as implementation. Evidence to connect: Activity review; risk and legal registers; worker input; objectives, owners, resources and measures of success. Diagram Provide competent people, usable current information and suitable resources. Operate the agreed controls and manage procurement, contractors, change and emergencies with worker involvement.
Evidence to connect: Current policies and procedures; competence evidence; maintenance and operational records; contractor, change and emergency arrangements. Diagram Evaluate reliable monitoring and measurement, relevant compliance evidence, internal audits and management review. Routine checks and independent audit serve different purposes; low accident numbers alone cannot show that controls work. Evidence to connect: First-line checks; exposure and control-performance information; compliance evaluations; audit samples and management-review decisions. Diagram Respond to incidents, nonconformities and ineffective controls. Protect people, address the causes, assign action and verify effectiveness, then update affected risks, arrangements and competence requirements. Evidence to connect: Corrective actions with owners and dates; cause analysis; verified changes; revised documents and feedback into the next plan.
Diagram Leaders own the effectiveness of the OH&S system, set priorities and provide resources. Context defines what the system must address; worker consultation and participation inform decisions throughout the cycle, not just at the centre. Evidence to connect: An accurate system scope; policy commitments; clear authority and responsibilities; worker participation; resource and review decisions followed through. Diagram Read the picture as a learning aid, not an official ISO clause diagram. Its risk-profiling label sits under Do; ISO planning also addresses hazards, risks, opportunities and relevant obligations before work begins. Likewise, formal ISO management review is part of performance evaluation, with its decisions feeding subsequent improvement. Activities can span more than one stage.
The complete PDCA and management-system explanation ISO 45001 connection In the SHAREhub environment: link the risk or objective, its current arrangement, monitoring evidence and any improvement action. Retain a responsible owner, relevant dates and evidence that the change worked; a link between records is not proof of effectiveness. The cycle can organise a management system, but the diagram, a document library or a completed checklist does not establish conformity, certification or legal compliance. Use the authorised applicable standard and actual workplace evidence. Do not wait for the next audit or annual review to address an ineffective control. Interpretation and edition references: HSE: managing health and safety through PDCA; ISO/TC 283: ISO 45001 clause-family guidance and FAQs; ISO 45001: published edition and scope.
Source links checked 2026-10-20; this is not whole-page technical approval.
How do first-line proactive checks connect to auditing?
Source: active-and-reactive-monitoring--first-line-monitoring
From everyday checks to independent assurance Start close to the work: workers and supervisors check whether the controls needed for the activity are actually working. Use the routine checklists in the auditing area of the SHAREhub environment for this first-line proactive monitoring. Findings then inform specialist challenge, internal audit, external assurance and management review. These are complementary activities, not gates that must be completed in order. Open routine checklistsBrowse detailed audits Action and review connect every stage. A failed control, incident or near miss can trigger immediate intervention and a targeted review at any time. Do not wait for the next audit. In Audits and routine checks → Routine checklists, choose a relevant starting template.
Check its questions against the actual risk assessment, equipment, workplace and approved arrangements before use; a generic form is not a complete assessment. Keep records proportionate. HSE notes that the simplest work-equipment pre-use checks do not normally need a record. Formal inspection records and specialist examinations have their own requirements; a routine checklist does not replace them. Keep sensitive information out of general check records. Saving a form is not the same as notifying an action owner: confirm the finding has reached them through your agreed reporting route. Illustrative, not a live task instruction. During a substance-task start check, an operator finds the extraction indicator outside its specified operating range. The affected exposure-generating work is held and the supervisor arranges competent investigation.
The action record identifies the equipment, protection measures, repair owner and evidence required before hand-back. Repeat findings lead the specialist to review maintenance and how users recognise faults. An internal audit then samples similar equipment, inspection records and whether repairs stay effective. An external reviewer may challenge that evidence within their scope. Management funds the underlying improvement and subsequent checks test it. Any exposure or near miss is also investigated through the reactive route; none of these activities waits for an annual audit. Open the detailed COSHH and exposure control audit · Read the full auditing guidance · Connect findings to the management system This is a practical monitoring route, not a legally required four-stage sequence.
HSE guidance applies in Great Britain; use the applicable Northern Ireland legislation and HSENI guidance for Northern Ireland work. Neither the checklist nor the assurance diagram certifies compliance. Links checked 18 October 2026. This addition is an editorial update, not independent technical approval of the topic or a workplace arrangement.
What is active and reactive monitoring?
Source: active-and-reactive-monitoring--what-is-it
Active monitoring checks control performance before harm; reactive monitoring learns from harm, near harm or other signs of failure after the event. Source basis: HSE HSG65 Managing for health and safety · HSE HSG245 Investigating accidents and incidents (2004 edition; verify current HSE listing). Illustrative conveyor example: the first scene checks the stationary guard before use; the second raises a guard defect. Hold the affected machine until a competent check demonstrates that the required guarding function has been restored and the authorised owner accepts the hand-back. Monitoring is the checking part of the health and safety management cycle. HSE’s Plan, Do, Check, Act approach expects organisations to check performance, investigate the causes of problems and review whether arrangements remain effective.
Without monitoring, risk assessments and procedures can look complete while the real workplace quietly drifts away from the intended control standard. Active monitoring is forward-looking. It asks whether the controls that should prevent harm are present, suitable, used, maintained and understood today. It includes planned inspections, safety tours, audits, sampling, exposure monitoring, maintenance checks, behavioural observations, permit audits, document reviews, contractor checks and worker conversations. Reactive monitoring is backward-looking, but it is still valuable. It uses information from accidents, near misses, dangerous occurrences, ill-health reports, complaints, first-aid records, absence, property damage, enforcement, claims and non-conformities. The aim is not to count bad news; it is to understand what failed and whether similar weaknesses exist elsewhere.
Why does active and reactive monitoring matter?
Why does active and reactive monitoring matter?
Source: active-and-reactive-monitoring--why-it-matters
Monitoring matters because a workplace can look safe while important controls are missing, degraded, misunderstood or no longer matched to the real risk. A business that only looks at accident numbers can miss serious weakness. Some hazards rarely produce frequent injuries but can still cause catastrophic harm: fire, explosion, work at height, confined spaces, traffic movement, occupational disease, asbestos exposure, violence, machinery entanglement or contractor interface failures. A quiet injury record may mean good control, but it may also mean luck, low exposure, under-reporting or workers who do not trust the reporting system. Active monitoring gives managers earlier warning.
A missing guard, failed extraction system, untested alarm, poor housekeeping standard, expired training certificate, incomplete permit or overdue statutory inspection is useful intelligence before someone is harmed. The value is in acting on that intelligence, not in collecting a checklist. Reactive monitoring gives depth. A near miss, first-aid case or complaint can show how controls behave under pressure. A good organisation studies the event pathway: what was planned, what actually happened, what people understood, which barriers worked, which barriers failed and what organisational decisions created the conditions. A low injury count can coexist with a failing barrier, poor reporting or a long-latency health exposure.
An inspection therefore asks whether the control prevents the credible harm route now; a reactive review asks why it failed and whether the same weakness exists elsewhere. Neither a checklist nor a dashboard is proof without workface evidence.
How do active and reactive monitoring work in real tasks?
Source: active-and-reactive-monitoring--operational-examples
Start with the control and the decision it supports, then use both planned checks and reports of failure to improve it. These are original teaching examples, not site procedures or fixed inspection frequencies. A scheduled inspection is active; an unexpected defect report is reactive. The same defect can appear in both records, but the trigger and decision must remain clear. Short transfer cases: A scheduled tour finds a fire door that will not close: protect the route and require competent repair before treating the check as complete. A loose gym-machine guard found on inspection is an active-monitoring defect: isolate the machine and check similar units. If it loosened during use and almost harmed someone, record and investigate that event as a near miss too.
A contractor changing a plant-room isolation calls for a pre-work verification and a hand-back check. A pool-opening test that is out of the applicable site standard holds opening until competent verification; no generic numeric limit is inferred.
How can the ISO 45001 hierarchy of controls guide corrective action after safety monitoring?
Source: active-and-reactive-monitoring--active-monitoring
Active monitoring should check the real condition of risk controls before harm occurs, using a planned and risk-based approach. Active monitoring should be designed around the significant risks in the organisation. It should not simply repeat easy low-risk checks because they are quick to complete. A construction business may need work at height, plant, lifting, dust and contractor checks. A leisure business may need pool water checks, lifeguard supervision observations, fire checks, food safety interface checks, plant-room inspections and event risk checks. A chemical site may need permit audits, alarm testing, containment inspections and exposure monitoring. Frequency should follow risk. Critical controls, high-hazard tasks, new starters, contractors, poor previous performance and changing work need closer checking. Lower-risk stable activities can be checked less often.
Objectivity matters: the person checking must be able to recognise the standard and challenge drift, not simply confirm their own work is acceptable. A good active monitoring system combines document review with field evidence. Records may show that a weekly inspection was completed, but observation may show that people cannot follow the procedure because equipment is missing, access is poor or the checklist does not reflect the actual task. A machine-guard example shows what monitoring must prove. The strongest decision is to design out access to the moving part where practical; a different feed arrangement can substitute for repeated hand entry. Where access remains, a fixed or interlocked guard is an engineering control, and a marked exclusion zone and authorised isolation method are administrative safeguards.
Gloves do not make contact with moving parts safe. In ERICPD terms, removing access is Eliminate, changing the feed is Reduce, the guard is Isolate/Control, and Discipline is the planned proof that the guard still works. The machine owner records why each stronger measure was or was not selected for this task. Before a shift, an operator checks that the guard and stop function are present and reports a defect; maintenance tests the protective function to the approved method after repair; the supervisor samples actual use and closes bypass reports. A near miss is a reactive signal that must be compared with these active checks, not just added to a dashboard.
The manager looks for missing checks, repeated bypasses and unclosed defects, assigns an owner and tests effectiveness after the change. A failed interlock, unknown guard status or repeated bypass is a hold on the machine until competent verification and release, even if the dashboard percentage appears favourable. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level. The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation"). ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.
How should active monitoring work at different assurance levels?
Source: active-and-reactive-monitoring--assurance-levels
Active monitoring should operate through layered assurance, from frontline checks through management and specialist review to independent verification. A strong monitoring system uses several levels of assurance because each level sees different evidence. Frontline workers and supervisors see the task as it happens. Managers and health, safety, security and environment specialists see patterns across teams, shifts and departments. Independent internal audit provides objective challenge to the organisation. External consultants and certification auditors may provide separate assurance within an agreed scope; independence is not established by a job title. The IIA Three Lines Model distinguishes management's first- and second-line roles from independent internal audit in the third line. External assurance is separate.
These roles work alongside one another, not as sequential gates: operational owners manage risk, specialists support and challenge them, and independent internal audit tests arrangements objectively. Prevent self-review where roles overlap. The mistake is asking one line of defence to do everything. A supervisor inspection cannot replace an independent audit of the management system. An external audit cannot replace daily frontline checks of whether a guard, extraction system, permit control or safe route is actually in place. The levels should connect, so local findings can be escalated and independent findings can change how work is controlled.
What should reactive monitoring include?
What should reactive monitoring include?
Source: active-and-reactive-monitoring--reactive-monitoring
Reactive monitoring should turn accidents, near misses, ill health and complaints into learning that improves controls. Source basis: HSE HSG245 Investigating accidents and incidents (2004 edition; verify current HSE listing) · HSE How to manage health and safety. Reactive monitoring starts with reporting culture. If workers fear blame, believe nothing changes, cannot access the reporting route or only report injuries, the organisation will receive distorted data. A mature system encourages reporting of near misses, unsafe conditions, defects, symptoms, complaints, property damage, environmental releases and control failures. Reactive data must then be investigated at a level proportionate to actual and potential consequence. A minor first-aid injury may need simple review. A high-potential near miss may need a deeper investigation even if nobody was hurt.
The organisation should look for immediate, underlying and root causes and test whether similar weaknesses exist elsewhere. The best reactive monitoring does not stop when an action is entered into a tracker. It asks whether the action has actually reduced risk. If the corrective action is only a reminder, poster or email, it may not address the conditions that made the event likely.
How should leading and lagging indicators be used?
Source: active-and-reactive-monitoring--indicators
Leading indicators help predict control weakness, while lagging indicators show harm or failure that has already occurred. Source basis: HSE HSG65 Managing for health and safety · HSE HSG254 Developing process safety indicators. Fictional indicator comparison. Define the period and activity before interpreting counts; zero recorded injuries cannot outweigh evidence that a critical control has failed. The worked example below uses one warehouse review week. Source basis: HSE HSG65 Managing for health and safety · HSE workplace injury definitions and formulae. A useful indicator changes decisions. Counting something because it is easy to count can produce a dashboard that looks busy but says little about risk. For example, “number of inspections completed” is weak if inspections are superficial.
“Percentage of critical actions overdue” or “repeat defects found in the same area” may be more useful because it points to control failure. Leading indicators should be close to the controls that prevent serious harm. For work at height, that may include scaffold inspection quality, edge protection defects and permit compliance. For occupational health, it may include exposure-monitoring results, health-surveillance attendance, LEV test failures or repeat symptom reports. For process safety, it may include safety-critical maintenance backlog or alarm impairment. Lagging indicators should be interpreted carefully. They are essential for learning, but they arrive after failure. They can also be affected by under-reporting, workforce size, hours worked, changing work mix and whether workers trust the reporting system.
A balanced review looks at both leading and lagging evidence together.
Read counts alongside activity and control evidence
Source: active-and-reactive-monitoring--monitoring-dashboard-context
The zero-injury dashboard is a fictional teaching example, not a SHARE performance claim. Give every real indicator a defined period, site or activity, data source and exposure measure before comparing it over time. Guidance: HSE managing for health and safety.
What would make this action closable?
Source: active-and-reactive-monitoring--monitoring-action-proof
Fictional pool-opening example: the opening check identifies a disinfectant result outside the pool’s agreed operating range. The duty manager keeps the affected area closed and records the fault. A temporary barrier records the restriction; it does not demonstrate that the water condition has been restored. Write what failed, the affected area or task and the temporary restriction. Identify who owns that restriction. Record the required function and how it will be checked. State who is competent to test it and who can accept the hand-back. Attach the actual result, date and tester. An invoice, photograph or action-status tick may support the record but does not replace the functional evidence. Record the acceptance and any limits.
Check the control again during normal use; reopen the action if the fault recurs or conditions change. Use the editable monitoring record for readable fields and printing. Record finding, control affected, owner, due date, hold scope, acceptance criterion, evidence, authorised decision and review trigger. Guidance: HSE managing for health and safety · HSE developing process safety indicators · HSE health and safety in swimming pools.
What should be checked before, during and after monitoring?
Source: active-and-reactive-monitoring--checks
Define the risk, standard, checker, decision and escalation before collecting a number; close the loop only when the changed control works. Before a check, name the material risk, the control standard, the competent checker, the decision owner and what will trigger an immediate hold. During the check, observe the real task, speak with people doing it and record failed or uncertain controls without smoothing away exceptions. Afterward, protect people, assign an action and verify its effect in use. Set the interval by the risk profile and any task-specific legal or manufacturer requirement; no universal inspection frequency applies.
How should inspections, sampling and safety tours be planned?
Source: active-and-reactive-monitoring--inspections
Inspections, sampling and tours should be planned by risk, carried out competently and used to test what is actually happening. Browse both pages of the existing SHARE opening walk-round checklist: the twelve checks, followed by findings, actions and verification. Use the page controls; the preview does not advance automatically. Checklist page preview. Open the linked full-size document for the original fields; the editable monitoring record and closure example on this page provide a readable finding, owner, hold, acceptance and verification route. Checklist page preview. Open the linked full-size document for the original fields; the editable monitoring record and closure example on this page provide a readable finding, owner, hold, acceptance and verification route.
Source basis: HSE HSG65 Managing for health and safety · HSE Managing risks and risk assessment at work. Source basis: HSE HSG65 Managing for health and safety · HSE Managing risks and risk assessment at work. Inspection frequency should not be copied blindly from another business. It should reflect the severity of harm, how quickly conditions can change, the reliability of controls, previous findings, legal requirements, manufacturer instructions and the competence of people doing the work. A high-risk temporary work area may need daily checks, while a stable low-risk office area may need less frequent inspection. Checklists can help consistency, but they can also create tunnel vision. A checklist should include critical controls and prompt the inspector to look for change, drift and weak signals.
It should also leave space for professional judgement, worker comments and items that were not expected when the checklist was written. Objectivity is important. People can become blind to familiar weaknesses in their own area. Cross-inspections, safety representative involvement, independent audits or supervisor rotation can improve challenge, but the person still needs enough competence to understand what good looks like.
What makes monitoring data trustworthy?
What makes monitoring data trustworthy?
Source: active-and-reactive-monitoring--data-quality
Monitoring data is trustworthy when it is accurate, complete, understood, timely and connected to real decisions. Health and safety data can be misleading. A fall in reported near misses may mean fewer near misses, but it may also mean workers have stopped reporting. A high number of inspection findings may mean poor conditions, but it may also mean inspections have become more honest. A completed action may not mean risk has reduced if the action was weak or unverified. Good data quality needs clear definitions. Everyone should know what counts as a near miss, unsafe condition, hazard observation, first-aid case, occupational health concern or high-potential event. Without common definitions, departments may record the same event differently and leadership may compare unreliable numbers.
Data also needs context. Monitoring should consider hours worked, work type, season, contractor activity, temporary projects, workforce changes, reporting culture and exposure levels. Context turns numbers into learning. Compare like with like. Before comparing a rate between sites or periods, record the numerator, denominator, population or work scope, time period, inclusion rules and missing data. A contractor injury rate per hours worked cannot be compared fairly with a headcount-based employee figure, and a fall in reports during missing-data periods is not an improvement.
How should monitoring feed into management review?
Source: active-and-reactive-monitoring--management-review
Monitoring should lead to decisions about controls, resources, objectives, competence and priorities. Source basis: HSE HSG65 Managing for health and safety · HSE INDG417 Leading health and safety at work (Revision 1, 2013; live English page). Management review is where monitoring becomes leadership. If monitoring data is only filed or presented as a set of charts, the loop is not closed. Leaders should ask what the data says about serious risks, whether controls are working, whether weak signals are escalating, whether actions are overdue and whether resources are being directed to the right places. The review should include both operational detail and strategic questions. Operationally, managers need to know whether inspections, audits, exposure monitoring, health surveillance and incident investigations are being completed and acted on.
Strategically, leaders need to know whether the organisation is learning, whether objectives remain suitable and whether the risk profile has changed. The output should be visible. Review should result in actions, changed priorities, revised objectives, improved controls, better training, procurement decisions, contractor interventions or changes to leadership expectations. When a critical check fails, leaders should make an immediate protection decision rather than wait for a scheduled dashboard meeting. Periodic management review then tests trends, repeated findings, action quality, workforce reports and whether changes in work have made the original measures obsolete. Record the decision, resources, owner and later evidence of effectiveness.
Which monitoring and incident-reporting duties apply in GB and NI?
Source: active-and-reactive-monitoring--legal
GB and NI each require suitable risk assessment and effective arrangements to plan, control, monitor and review protection; they have different incident-reporting regulations. Source basis: HSE RIDDOR reportable incidents · HSE When do I need to report an incident? · HSENI Report an incident · HSENI reporting criteria and timing. In Great Britain, the Management of Health and Safety at Work Regulations 1999, particularly regulations 3 and 5, sit with the Health and Safety at Work etc. Act 1974. In Northern Ireland, use the Management Regulations (NI) 2000, particularly regulations 3 and 5, and the Health and Safety at Work (NI) Order 1978. The exact check frequency follows risk and any specific rule for the equipment or activity; this page sets no universal interval.
Reportability is a separate decision. GB RIDDOR 2013 has an over-seven-day injury reporting threshold and over-three-day recording requirement; NI RIDDOR 1997 (as amended) retains over-three-day reporting. Certain deaths, specified injuries, occupational diseases and dangerous occurrences have their own criteria. Check the current HSE or HSENI route promptly; investigate serious near misses even when not reportable. HSG245 was published in 2004 and its GB reporting wording is superseded; use it for investigation method and current HSE or HSENI guidance for reporting thresholds.
Worked day-count example, checked against current HSE and HSENI guidance on 25 September 2026: if a worker has a work-related accident on Thursday and cannot do normal duties through Monday, count Friday, Saturday, Sunday and Monday as four consecutive days; exclude the accident day and include weekends or rest days. Subject to the other RIDDOR criteria, this is an over-three-day report in Northern Ireland, due within 10 days of the incident. In Great Britain it is an over-three-day record, not an over-seven-day injury report. If incapacity continues through the following Friday, the eight consecutive days after the accident cross the GB over-seven-day reporting threshold, due within 15 days of the incident. First protect people and make the situation safe.
Check death, specified or major injury, disease, dangerous-occurrence and non-worker categories separately with the current regulator guidance; a non-reportable event can still demand prompt investigation and corrective action. Monitoring is a workplace-use duty and management practice, not a product-supply or conformity-marking certificate. ISO 45001 may support assurance but is voluntary unless adopted by the organisation or contract.
What should the monitoring register include?
Source: active-and-reactive-monitoring--register
A monitoring register should link significant risks, controls, checks, findings, owners, actions and review triggers. A monitoring register helps prevent fragmented checking. Without a register, fire checks, plant checks, inspections, audits, incident reviews, exposure monitoring and training reviews can sit in separate systems that nobody reads together. The register should show which controls are critical, how they are checked and what happens when they fail. The register should also distinguish activity from assurance. Recording that an inspection happened is activity. Showing that the inspection checked the right controls, found meaningful issues, closed actions and reduced repeat findings is assurance.
A practical monitoring register records the significant risk and control, its standard, location, checker and competence, planned or event trigger, actual result, people exposed, immediate protection, action owner and due date, evidence location and effectiveness decision. Restrict identifiable health records; use a proportionate trend summary for management learning.
How could Riverside Leisure Ltd use active and reactive monitoring?
How could Riverside Leisure Ltd use active and reactive monitoring?
Source: active-and-reactive-monitoring--business-example
Riverside Leisure Ltd would use active and reactive monitoring to check daily operational controls and learn from first-aid cases, complaints, near misses and audit findings. Source basis: HSE HSG65 Managing for health and safety · HSE How to manage health and safety. Fictional pool-opening hold following a water-quality check outside the operating plan’s acceptance range. The barrier keeps people out while the competent pool operator investigates and verifies restoration. Only the authorised duty manager can accept the recorded hand-back and reopen the affected area. Riverside Leisure Ltd is a fictional operator of leisure centres, outdoor activity venues and public events.
Its risk profile includes swimming pools, wet changing areas, gyms, sports courts, catering, plant rooms, contractors, young people, visitors, events, fire safety, legionella, manual handling, work at height and lone working. A single accident rate would tell senior leaders very little about whether those controls are healthy. The company uses active monitoring to check whether controls are present before harm occurs: pool water tests, lifeguard supervision observations, wet-floor inspections, fire alarm checks, gym equipment checks, playground inspections, contractor permits, plant-room access controls and cleaning standards. It uses reactive monitoring to learn from first-aid records, slips, customer complaints, near misses, maintenance defects, ill-health reports and staff absence. The important part is the loop. Findings are not left in site folders.
Each centre manager reviews weekly control data, regional managers compare trends monthly, and senior leaders review high-potential events, overdue actions and repeat defects quarterly. Where findings repeat, Riverside changes procurement, staffing, training, supervision or maintenance planning rather than asking staff to be more careful. Riverside also separates the assurance levels deliberately. First-line checks are mainly binary and repeatable, so the business can baseline whether essential controls are being applied consistently. Second-line checks are more interpretive and are completed by competent leaders or HSSE specialists who can judge the quality of documents, records and field practice. Third-line audits are planned as evidence-based assurance reviews, sampling live activities, policies, training records, maintenance logs, incident data and management-system records before ranking findings and assigning verifiable actions.
At Riverside Leisure, a duty manager can compare planned checks of plant, access, staffing and emergency readiness with first-aid events, complaints, near misses and worker reports. A failed critical check holds the affected activity; a repeated event pattern prompts a fresh look at task design and control condition. The owner records what changed and observes the control in service before closing the action. Riverside roles and thresholds are illustrative local arrangements, not fixed legal rules.
What training is needed for active and reactive monitoring?
Source: active-and-reactive-monitoring--training
Training should help people recognise weak controls, report honestly, inspect competently and turn findings into better decisions. Training should match the role. Workers need awareness of what to report and why near misses matter. Supervisors need practical inspection and observation skills. Managers need to interpret indicators and prioritise actions by risk. Safety professionals and auditors need to test whether the monitoring system is reliable, objective and connected to the organisation’s serious risks. A weak training approach teaches people to complete forms. A strong approach teaches them what good looks like, what failure looks like, how to ask useful questions, how to record evidence and how to escalate unacceptable conditions.
Train each checker on the control being tested, the instrument or observation method, the result that requires a hold and the person to contact. Test competence in the field, including what to do with an uncertain reading; attendance alone does not demonstrate it. Managers also need skill in challenging a reassuring number when near misses or worker accounts point the other way.
How can ISO 45001 support active and reactive monitoring?
Source: active-and-reactive-monitoring--management-system
ISO 45001 is a voluntary occupational health and safety management-system standard. Its exact current edition and amendments require an authorised copy; its broad performance-evaluation and improvement themes can help a business connect inspections, exposure checks, incident learning and management decisions. Active and reactive monitoring maps naturally into a management system. The topic is not a single procedure; it is how the organisation checks whether risk controls, objectives, competence, consultation and actions remain effective. Use the current licensed edition for formal clause mapping. In daily work, connect monitoring to control ownership, competent inspection, credible data, management decisions and verified improvement. ISO 45001 is voluntary unless adopted by contract or policy, and it is not a substitute for GB or NI law or a functioning control.
Its scope and status are recorded in the official source link below.
How does active and reactive monitoring support IOSH National General Certificate study?
Source: active-and-reactive-monitoring--study
This topic maps directly to IOSH National General Certificate GNC 4.2 and is commonly tested through practical scenario questions. For GNC 4.2, learners should be able to explain the difference between active and reactive monitoring and give practical examples of each. They should also understand inspections, sampling and tours; how to decide frequency; why competence and objectivity matter; how checklists should be used; how responsibilities and priorities are set; and how ill-health and incident data contribute to reactive monitoring. A strong scenario answer does not simply list “inspection, audit, accident records”. It explains what the organisation is trying to learn.
For example, if a warehouse has few reported accidents but many damaged racking uprights, poor traffic segregation and overdue FLT refresher training, active and reactive monitoring together suggest the control system is weak even if the injury rate is low. In exam-style answers, use workplace language: what would be inspected, who would inspect it, how often, what competence is needed, what records are kept, how findings are prioritised and how management will check that actions reduced risk. A strong GNC 4.2 answer compares a planned check before harm with evidence gathered after a failure, then gives a task example, names the control standard, explains what the result changes and shows how the action is verified. Injury numbers alone are an incomplete performance measure.
What are the warning signs that monitoring is not working?
Source: active-and-reactive-monitoring--warning-signs
Monitoring is failing when it produces numbers but does not reveal weak controls, change decisions or reduce repeated findings. The warning signs are often visible in ordinary management information. Inspections are always green, actions are repeatedly overdue, near misses are rarely reported, the same defects return every month, workers say nothing changes, or managers celebrate low accident numbers while serious controls are untested. Each warning sign can cause harm because it allows the organisation to believe it is managing risk when it is only managing paperwork. Monitoring should challenge comfort, not protect it.
Escalate when the same defect returns, inspection completion rises while critical findings remain open, health symptoms cluster, workers stop reporting near misses, or an action is closed after sending a reminder without seeing the changed work. These are signals to test the measure and the reporting culture, not proof that an individual worker is the hazard.
Repeated cleaner skin symptoms
Repeated cleaner skin symptoms
Source: active-and-reactive-monitoring--example--repeated-cleaner-skin-symptoms
Task Material And Setting: Several cleaners report dermatitis symptoms despite completed cleaning checklists; protect people and investigate the real exposure route. The harmful exposure is repeated wet work or product contact with the skin; irritation or allergy can develop depending on the substance and exposure. People And Prerequisites: Cleaners, agency staff and people contacting residues may be affected. Use actual product data, task observation and occupational-health advice when needed. Before: Record symptoms confidentially and review the actual product, task and affected work group. During: Inspect dosing, dilution, contact routes and glove selection, consult workers and change source controls. Hold Or Stop: Hold the affected method when contact is uncontrolled or symptoms continue. The manager and competent health adviser decide adjustments and any surveillance route.
Completion And Hand Back: Check that changed controls work and workers can use them before routine work resumes. Evidence: Keep anonymised trends, assessment and follow-up; retain individual confidential health records separately. Source Context For This Decision: HSE; HSE
Warehouse vehicle near miss after layout change
Source: active-and-reactive-monitoring--example--warehouse-vehicle-near-miss
Task Material And Setting: A reversing vehicle misses a pedestrian after temporary storage narrows the route; restore physical separation and review the changed layout. A moving vehicle can transfer force to a pedestrian, causing crush injury or death even when this event injured nobody. People And Prerequisites: Drivers, pedestrians, contractors and visitors may be affected. The manager confirms the actual traffic route, vehicle movements and control owner. Before: Stop movements and separate people before inspecting the temporary layout. During: Consult route users and revise physical traffic controls before work resumes. Hold Or Stop: Hold route reopening until the site lead checks the controls. Do not accept zero injury as proof of safety or rely on another warning poster alone.
Completion And Hand Back: Observe the revised route in live use and adjust it if controls fail. Evidence: Retain the near-miss account, layout change, action owner, route approval and effectiveness verification. Source Context For This Decision: HSE; HSE
Documents to download
Source: active-and-reactive-monitoring--editable-documents
Download editable resources from the SHAREhub environment. Working forms and spreadsheet input areas are blank. Reports, plans, guides, briefings, procedures and policies contain completed fictional example content to adapt.
Access and egress routine inspection
: Blank checklist. Eight positive control questions, critical failures, findings and verification in the current SHAREi routine style.
BuildOut monthly monitoring review
: Completed fictional review report. A completed March review follows a defined sample from planned checks to evidence gaps, failed safeguards, a reopened action and management decisions.
BuildOut UK Ltd health and safety assurance plan
: Completed example plan. Completed 2027 plan for four fictional sites: 26 risk-linked activity checks, a 12-month supervisor and manager schedule, 13 scheduled audits and reviews, and assurance coverage across 35 management policy areas.
Risk based assurance delivery record
: Blank record with separate worked example and programme reference. A blank monitoring log with live evidence and due-date prompts, 33 separate fictional records, and the existing BuildOut annual programme and risk catalogue for reference.
Warehouse access inspection report
: Completed worked report. A photographic findings report that connects route observations to evidence, actions and checks during busy delivery periods.
Source tables and records 1
Bad KPI versus useful KPI examples
Table ID: kpi-s-bad-kpi-versus-useful-kpi-examples
Source: https://www.sharehub.ltd/knowledge-hub/kpi-s.html Scope: HSE sources provide GB regulator guidance used here for a transferable method, not Northern Ireland legal authority. Use the NI legislation and HSENI routes in the legal section for NI duties and incident reporting.
Row 1
- Bad or weak kpi
Number of inspections completed
- Why it can mislead
It counts activity but not whether important controls were effective.
- More useful kpi
Percentage of critical controls verified as effective, with high-risk defects closed and rechecked. Sources: HSE HSG254: Developing process safety indicators.
Row 2
- Bad or weak kpi
Zero accidents
- Why it can mislead
It may reflect luck, under-reporting or low exposure rather than good control.
- More useful kpi
Near-miss reporting quality, repeat-event themes, action closure and control-health trend. Sources: HSE HSG65: Managing for health and safety.
Row 3
- Bad or weak kpi
Training completed
- Why it can mislead
Attendance does not prove competence or safe behaviour in the task.
- More useful kpi
Competence observed during task, supervisor coaching completed and recheck after change. Sources: HSE HSG65: Managing for health and safety.
Row 4
- Bad or weak kpi
Toolbox talks delivered
- Why it can mislead
A talk can be delivered without understanding or behaviour change.
- More useful kpi
Briefing understanding checked, worker questions captured and field observations confirm application. Sources: HSE HSG65: Managing for health and safety.
Row 5
- Bad or weak kpi
Actions closed on time
- Why it can mislead
Actions may close administratively without fixing the system.
- More useful kpi
Actions closed with evidence, effectiveness review and no repeat finding after sampling. Sources: HSE HSG65: Managing for health and safety.
Row 6
- Bad or weak kpi
Audits completed
- Why it can mislead
Audit volume does not prove audit quality.
- More useful kpi
Risk-ranked findings, systemic themes, overdue verification and leadership response. Sources: HSE HSG65: Managing for health and safety.
Read the complete comparison table
| Row | Bad or weak kpi | Why it can mislead | More useful kpi |
|---|---|---|---|
| 1 | Number of inspections completed | It counts activity but not whether important controls were effective. | Percentage of critical controls verified as effective, with high-risk defects closed and rechecked. Sources: HSE HSG254: Developing process safety indicators. |
| 2 | Zero accidents | It may reflect luck, under-reporting or low exposure rather than good control. | Near-miss reporting quality, repeat-event themes, action closure and control-health trend. Sources: HSE HSG65: Managing for health and safety. |
| 3 | Training completed | Attendance does not prove competence or safe behaviour in the task. | Competence observed during task, supervisor coaching completed and recheck after change. Sources: HSE HSG65: Managing for health and safety. |
| 4 | Toolbox talks delivered | A talk can be delivered without understanding or behaviour change. | Briefing understanding checked, worker questions captured and field observations confirm application. Sources: HSE HSG65: Managing for health and safety. |
| 5 | Actions closed on time | Actions may close administratively without fixing the system. | Actions closed with evidence, effectiveness review and no repeat finding after sampling. Sources: HSE HSG65: Managing for health and safety. |
| 6 | Audits completed | Audit volume does not prove audit quality. | Risk-ranked findings, systemic themes, overdue verification and leadership response. Sources: HSE HSG65: Managing for health and safety. |
Worked KPI calculations and evidence gaps
Table ID: kpi-s-reconciliation
Source: https://www.sharehub.ltd/knowledge-hub/kpi-s.html Scope: Original SHARE fictional arithmetic and local indicator definitions, not HSE-prescribed rates or tolerances. GB HSE guidance supports transferable monitoring methods, not NI legal authority; NI workplace duties and reporting use the separate NI sources.
Row 1
- Measure
Observed pass rate
- Calculation
72 passed ÷ 80 valid completed checks × 100 = 90%.
- Meaning
This answers how completed checks performed. Display the eight failures and 20 missing records alongside it; 90% is not coverage. Sources: HSE HSG65: Managing for health and safety.
Row 2
- Measure
Evidence coverage
- Calculation
80 valid completed checks ÷ 100 due × 100 = 80%.
- Meaning
Twenty due checks have no valid result. Find out which controls lack evidence and make a risk decision; do not invent passes or failures. Sources: HSE HSG65: Managing for health and safety.
Row 3
- Measure
Verified pass evidence against all due
- Calculation
72 verified passes ÷ 100 due × 100 = 72%.
- Meaning
Call it this explicitly. The other 28 comprise eight known failures and 20 unknown results, which need different follow-up. Sources: HSE HSG65: Managing for health and safety.
Row 4
- Measure
No activity due
- Calculation
0 completed ÷ 0 due: percentage undefined.
- Meaning
Display “not applicable: no checks due”, with the underlying zero counts. Confirm the activity really did not occur before accepting this status. Sources: HSE HSG65: Managing for health and safety.
Row 5
- Measure
Combined sites, a separate example
- Calculation
Site A: 980/1,000 = 98%; site B: 10/20 = 50%. Combined: 990/1,020 ≈ 97.1%.
- Meaning
Combine compatible counts, not percentages. Keep the site results visible: the large site dominates the total and the small site still has a serious gap. Sources: HSE HSG65: Managing for health and safety, HSE HSG254: Developing process safety indicators.
Read the complete comparison table
| Row | Measure | Calculation | Meaning |
|---|---|---|---|
| 1 | Observed pass rate | 72 passed ÷ 80 valid completed checks × 100 = 90%. | This answers how completed checks performed. Display the eight failures and 20 missing records alongside it; 90% is not coverage. Sources: HSE HSG65: Managing for health and safety. |
| 2 | Evidence coverage | 80 valid completed checks ÷ 100 due × 100 = 80%. | Twenty due checks have no valid result. Find out which controls lack evidence and make a risk decision; do not invent passes or failures. Sources: HSE HSG65: Managing for health and safety. |
| 3 | Verified pass evidence against all due | 72 verified passes ÷ 100 due × 100 = 72%. | Call it this explicitly. The other 28 comprise eight known failures and 20 unknown results, which need different follow-up. Sources: HSE HSG65: Managing for health and safety. |
| 4 | No activity due | 0 completed ÷ 0 due: percentage undefined. | Display “not applicable: no checks due”, with the underlying zero counts. Confirm the activity really did not occur before accepting this status. Sources: HSE HSG65: Managing for health and safety. |
| 5 | Combined sites, a separate example | Site A: 980/1,000 = 98%; site B: 10/20 = 50%. Combined: 990/1,020 ≈ 97.1%. | Combine compatible counts, not percentages. Keep the site results visible: the large site dominates the total and the small site still has a serious gap. Sources: HSE HSG65: Managing for health and safety, HSE HSG254: Developing process safety indicators. |
KPI ownership, challenge and review
Table ID: kpi-s-kpi-ownership-review
Source: https://www.sharehub.ltd/knowledge-hub/kpi-s.html Scope: HSE sources provide GB regulator guidance used here for a transferable method, not Northern Ireland legal authority. Use the NI legislation and HSENI routes in the legal section for NI duties and incident reporting.
Row 1
- Line
Work owner
- Kpi examples
Actual guard, isolation, permit and pre-use checks, with exceptions visible.
- Top tip
Hold unsafe work and verify correction; an activity count alone does not prove control. Source: HSE HSG65 managing for health and safety.
Row 2
- Line
Competent reviewer
- Kpi examples
Risk-ranked exceptions, sample quality, repeat defects and verified close-out.
- Top tip
Challenge weak definitions, optimistic samples and systemic risk; escalate findings. Source: HSE HSG65 managing for health and safety.
Row 3
- Line
Management review or independent check
- Kpi examples
Test control design, data quality, response and unresolved themes.
- Top tip
Decide resources and follow-up; independent review should not take over the work owner’s control decision. Source: HSE HSG65 managing for health and safety.
Read the complete comparison table
| Row | Line | Kpi examples | Top tip |
|---|---|---|---|
| 1 | Work owner | Actual guard, isolation, permit and pre-use checks, with exceptions visible. | Hold unsafe work and verify correction; an activity count alone does not prove control. Source: HSE HSG65 managing for health and safety. |
| 2 | Competent reviewer | Risk-ranked exceptions, sample quality, repeat defects and verified close-out. | Challenge weak definitions, optimistic samples and systemic risk; escalate findings. Source: HSE HSG65 managing for health and safety. |
| 3 | Management review or independent check | Test control design, data quality, response and unresolved themes. | Decide resources and follow-up; independent review should not take over the work owner’s control decision. Source: HSE HSG65 managing for health and safety. |
Task-specific HSE control hierarchy decisions
Table ID: kpi-s-hierarchy-worked
Source: https://www.sharehub.ltd/knowledge-hub/kpi-s.html
Row 1
- Level
Live-area contractor entry: 1 Elimination
- Measure
In the illustrative Crownway task, use remote inspection or complete fabrication outside the live area where the information and plant design allow; then no contractor crosses the live permit boundary.
- Check
Task owner records which entries were genuinely removed, with a field sample. Any unplanned entry or missing observation stops the release decision. Sources: HSE HSG254: Developing process safety indicators, HSE managing risk using PPE.
Row 2
- Level
Live-area entry: 2 Substitution
- Measure
Trial a lower-energy or off-site method that still proves the required condition; do not call a remote image equivalent to a physical test without technical acceptance.
- Check
Engineering owner signs the method specification and verifies the evidence. An unproven substitute is rejected. Sources: HSE HSG254: Developing process safety indicators, HSE managing risk using PPE.
Row 3
- Level
Live-area entry: 3 Engineering
- Measure
Before unavoidable entry, prove physical isolation and the relevant barrier or interlock at the boundary; a dashboard or induction record cannot create separation.
- Check
Permit issuer verifies isolation on the plant and records the check. Failed or uncertain barrier means no entry. Sources: HSE HSG254: Developing process safety indicators, HSE managing risk using PPE.
Row 4
- Level
Live-area entry: 4 Administrative
- Measure
Use a permit, boundary walk-through and task demonstration, then sample contractor understanding in the field. The KPI records failed checks and overdue fixes, not attendance alone.
- Check
Supervisor owns the hold and retest; manager trends exceptions and resources corrections. A failed boundary check overrides a 98% attendance result. Sources: HSE HSG254: Developing process safety indicators, HSE HSG65: Managing for health and safety.
Row 5
- Level
Live-area entry: 5 PPE
- Measure
Select any residual protection for the identified exposure and verify compatibility and fit; it does not replace isolation or a correct permit. Do not turn PPE issued into proof that a critical barrier works.
- Check
Competent selector checks condition and use; failed isolation remains a no-entry decision regardless of PPE. Sources: HSE managing risk using PPE, HSE HSG254: Developing process safety indicators.
Read the complete comparison table
| Row | Level | Measure | Check |
|---|---|---|---|
| 1 | Live-area contractor entry: 1 Elimination | In the illustrative Crownway task, use remote inspection or complete fabrication outside the live area where the information and plant design allow; then no contractor crosses the live permit boundary. | Task owner records which entries were genuinely removed, with a field sample. Any unplanned entry or missing observation stops the release decision. Sources: HSE HSG254: Developing process safety indicators, HSE managing risk using PPE. |
| 2 | Live-area entry: 2 Substitution | Trial a lower-energy or off-site method that still proves the required condition; do not call a remote image equivalent to a physical test without technical acceptance. | Engineering owner signs the method specification and verifies the evidence. An unproven substitute is rejected. Sources: HSE HSG254: Developing process safety indicators, HSE managing risk using PPE. |
| 3 | Live-area entry: 3 Engineering | Before unavoidable entry, prove physical isolation and the relevant barrier or interlock at the boundary; a dashboard or induction record cannot create separation. | Permit issuer verifies isolation on the plant and records the check. Failed or uncertain barrier means no entry. Sources: HSE HSG254: Developing process safety indicators, HSE managing risk using PPE. |
| 4 | Live-area entry: 4 Administrative | Use a permit, boundary walk-through and task demonstration, then sample contractor understanding in the field. The KPI records failed checks and overdue fixes, not attendance alone. | Supervisor owns the hold and retest; manager trends exceptions and resources corrections. A failed boundary check overrides a 98% attendance result. Sources: HSE HSG254: Developing process safety indicators, HSE HSG65: Managing for health and safety. |
| 5 | Live-area entry: 5 PPE | Select any residual protection for the identified exposure and verify compatibility and fit; it does not replace isolation or a correct permit. Do not turn PPE issued into proof that a critical barrier works. | Competent selector checks condition and use; failed isolation remains a no-entry decision regardless of PPE. Sources: HSE managing risk using PPE, HSE HSG254: Developing process safety indicators. |
KPI evidence standard
Table ID: kpi-s-kpi-evidence-standard
Source: https://www.sharehub.ltd/knowledge-hub/kpi-s.html Scope: HSE sources provide GB regulator guidance used here for a transferable method, not Northern Ireland legal authority. Use the NI legislation and HSENI routes in the legal section for NI duties and incident reporting.
Row 1
- Evidence
KPI dictionary
- What it proves
Definitions, scope and calculations are consistent.
- Quality check
Can every site calculate it the same way? Sources: HSE HSG65: Managing for health and safety.
Row 2
- Evidence
Risk-profile link
- What it proves
KPIs reflect significant risks.
- Quality check
Are top risks visible on the dashboard? Sources: HSE HSG254: Developing process safety indicators.
Row 3
- Evidence
Dashboard reviews
- What it proves
Leaders review performance regularly.
- Quality check
Are decisions, challenges and actions recorded? Sources: HSE HSG65: Managing for health and safety.
Row 4
- Evidence
Action tracker
- What it proves
Poor performance results in owned actions.
- Quality check
Are actions risk-ranked and verified? Sources: HSE HSG245: Investigating accidents and incidents.
Row 5
- Evidence
Audit samples
- What it proves
Data is tested for accuracy.
- Quality check
Do samples match records and work as done? Sources: HSE: Check performance.
Row 6
- Evidence
Trend analysis
- What it proves
The business learns from patterns.
- Quality check
Are repeat themes escalated? Sources: HSE HSG65: Managing for health and safety.
Row 7
- Evidence
Worker feedback
- What it proves
Indicators include workforce voice.
- Quality check
Are concerns closed with feedback? Sources: HSENI: Co-operation and monitoring safe working.
Read the complete comparison table
| Row | Evidence | What it proves | Quality check |
|---|---|---|---|
| 1 | KPI dictionary | Definitions, scope and calculations are consistent. | Can every site calculate it the same way? Sources: HSE HSG65: Managing for health and safety. |
| 2 | Risk-profile link | KPIs reflect significant risks. | Are top risks visible on the dashboard? Sources: HSE HSG254: Developing process safety indicators. |
| 3 | Dashboard reviews | Leaders review performance regularly. | Are decisions, challenges and actions recorded? Sources: HSE HSG65: Managing for health and safety. |
| 4 | Action tracker | Poor performance results in owned actions. | Are actions risk-ranked and verified? Sources: HSE HSG245: Investigating accidents and incidents. |
| 5 | Audit samples | Data is tested for accuracy. | Do samples match records and work as done? Sources: HSE: Check performance. |
| 6 | Trend analysis | The business learns from patterns. | Are repeat themes escalated? Sources: HSE HSG65: Managing for health and safety. |
| 7 | Worker feedback | Indicators include workforce voice. | Are concerns closed with feedback? Sources: HSENI: Co-operation and monitoring safe working. |
legal routes
Table ID: kpi-s-legal-routes
Source: https://www.sharehub.ltd/knowledge-hub/kpi-s.html
Row 1
- Area
General duty
- Gb
Health and Safety at Work etc. Act 1974 Sources: Health and Safety at Work etc. Act 1974.
- Ni
Health and Safety at Work (NI) Order 1978 Sources: Health and Safety at Work (Northern Ireland) Order 1978.
Row 2
- Area
Risk-management arrangements
- Gb
Management Regulations 1999 Sources: Management of Health and Safety at Work Regulations 1999.
- Ni
Management Regulations (NI) 2000 Sources: Management of Health and Safety at Work Regulations (NI) 2000.
Row 3
- Area
Incident reporting
- Gb
RIDDOR 2013; check GB specified categories and over-seven-day route Sources: HSE: RIDDOR reportable incident types.
- Ni
RIDDOR (NI) 1997; check NI major-injury categories and over-three-day route Sources: HSENI: Report an incident.
Read the complete comparison table
| Row | Area | Gb | Ni |
|---|---|---|---|
| 1 | General duty | Health and Safety at Work etc. Act 1974 Sources: Health and Safety at Work etc. Act 1974. | Health and Safety at Work (NI) Order 1978 Sources: Health and Safety at Work (Northern Ireland) Order 1978. |
| 2 | Risk-management arrangements | Management Regulations 1999 Sources: Management of Health and Safety at Work Regulations 1999. | Management Regulations (NI) 2000 Sources: Management of Health and Safety at Work Regulations (NI) 2000. |
| 3 | Incident reporting | RIDDOR 2013; check GB specified categories and over-seven-day route Sources: HSE: RIDDOR reportable incident types. | RIDDOR (NI) 1997; check NI major-injury categories and over-three-day route Sources: HSENI: Report an incident. |
competence
Table ID: kpi-s-competence
Source: https://www.sharehub.ltd/knowledge-hub/kpi-s.html
Row 1
- Role
Worker
- Learn
Control failure and honest reporting route
- Show
Explain and report a failed control even if monthly KPI is green
- Assessor
Supervisor
- Record
Scenario observation and report
- Again
Process or reporting route changes Sources: HSE HSG65: Managing for health and safety, HSENI: Co-operation and monitoring safe working.
Row 2
- Role
Supervisor
- Learn
Threshold, task hold, sample and escalation
- Show
Respond to failed critical check and trace a missing record
- Assessor
Operations manager
- Record
Observed decision and field verification
- Again
New risk or repeated defect Sources: HSE HSG254: Developing process safety indicators.
Row 3
- Role
KPI analyst
- Learn
Dictionary, numerator, denominator, sampling and data ethics
- Show
Reconcile dashboard with source records and explain uncertainty
- Assessor
Assurance lead
- Record
Test calculation and data-quality sample
- Again
System, definition or denominator changes Sources: HSE: Check performance, HSE HSG65: Managing for health and safety.
Row 4
- Role
Manager/director
- Learn
Risk trade-off, resource decision and closure assurance
- Show
Challenge a green dashboard with failed barrier and authorise corrective action
- Assessor
Competent senior leader or board
- Record
Decision log and effectiveness review
- Again
Major event, drift or strategy change Sources: HSE HSG65: Managing for health and safety, HSE HSG254: Developing process safety indicators.
Read the complete comparison table
| Row | Role | Learn | Show | Assessor | Record | Again |
|---|---|---|---|---|---|---|
| 1 | Worker | Control failure and honest reporting route | Explain and report a failed control even if monthly KPI is green | Supervisor | Scenario observation and report | Process or reporting route changes Sources: HSE HSG65: Managing for health and safety, HSENI: Co-operation and monitoring safe working. |
| 2 | Supervisor | Threshold, task hold, sample and escalation | Respond to failed critical check and trace a missing record | Operations manager | Observed decision and field verification | New risk or repeated defect Sources: HSE HSG254: Developing process safety indicators. |
| 3 | KPI analyst | Dictionary, numerator, denominator, sampling and data ethics | Reconcile dashboard with source records and explain uncertainty | Assurance lead | Test calculation and data-quality sample | System, definition or denominator changes Sources: HSE: Check performance, HSE HSG65: Managing for health and safety. |
| 4 | Manager/director | Risk trade-off, resource decision and closure assurance | Challenge a green dashboard with failed barrier and authorise corrective action | Competent senior leader or board | Decision log and effectiveness review | Major event, drift or strategy change Sources: HSE HSG65: Managing for health and safety, HSE HSG254: Developing process safety indicators. |
Warning signs and actions
Table ID: kpi-s-warning-signs-and-actions
Source: https://www.sharehub.ltd/knowledge-hub/kpi-s.html
Row 1
- Warning sign
Only lagging indicators
- What it suggests
The dashboard relies on outcomes or failures without checking preventive activities; a barrier failure or near miss can be a lagging result even when nobody is injured.
- Action
Add leading and control-health measures. Sources: HSE HSG254: Developing process safety indicators.
Row 2
- Warning sign
Perfect dashboards
- What it suggests
Under-reporting or weak challenge may exist.
- Action
Audit data quality and reporting culture. Sources: HSE HSG65: Managing for health and safety.
Row 3
- Warning sign
Huge number of measures
- What it suggests
Signal is buried in noise.
- Action
Focus on top risks and decisions. Sources: HSE HSG65: Managing for health and safety.
Row 4
- Warning sign
Actions closed with no evidence
- What it suggests
Paperwork closure is replacing improvement.
- Action
Require effectiveness checks. Sources: HSE: Check performance.
Row 5
- Warning sign
No worker voice
- What it suggests
Dashboard misses work-as-done signals.
- Action
Add participation and concern close-out measures. Sources: HSENI: Co-operation and monitoring safe working.
Row 6
- Warning sign
Repeated red indicators
- What it suggests
Escalation is weak.
- Action
Review ownership, resources and risk acceptance. Sources: HSE HSG65: Managing for health and safety.
Read the complete comparison table
| Row | Warning sign | What it suggests | Action |
|---|---|---|---|
| 1 | Only lagging indicators | The dashboard relies on outcomes or failures without checking preventive activities; a barrier failure or near miss can be a lagging result even when nobody is injured. | Add leading and control-health measures. Sources: HSE HSG254: Developing process safety indicators. |
| 2 | Perfect dashboards | Under-reporting or weak challenge may exist. | Audit data quality and reporting culture. Sources: HSE HSG65: Managing for health and safety. |
| 3 | Huge number of measures | Signal is buried in noise. | Focus on top risks and decisions. Sources: HSE HSG65: Managing for health and safety. |
| 4 | Actions closed with no evidence | Paperwork closure is replacing improvement. | Require effectiveness checks. Sources: HSE: Check performance. |
| 5 | No worker voice | Dashboard misses work-as-done signals. | Add participation and concern close-out measures. Sources: HSENI: Co-operation and monitoring safe working. |
| 6 | Repeated red indicators | Escalation is weak. | Review ownership, resources and risk acceptance. Sources: HSE HSG65: Managing for health and safety. |
Related SHARE pages
Table ID: kpi-s-related-share-pages
Source: https://www.sharehub.ltd/knowledge-hub/kpi-s.html Scope: HSE sources provide GB regulator guidance used here for a transferable method, not Northern Ireland legal authority. Use the NI legislation and HSENI routes in the legal section for NI duties and incident reporting.
Row 1
- Related page
Health and Safety Performance Monitoring, Measuring, Review and Audit
- Why it helps
Core performance management page.
Row 2
- Related page
Active and Reactive Monitoring
- Why it helps
Explains monitoring types and assurance layers.
Row 3
- Related page
Health and Safety Auditing
- Why it helps
Shows how audit evidence tests KPI quality.
Row 4
- Related page
Health and Safety Management Systems
- Why it helps
Connects KPIs to the management system.
Row 5
- Related page
Incident Investigation and Root Cause Analysis
- Why it helps
Turns lagging data into learning.
Row 6
- Related page
Near Miss
- Why it helps
Important weak-signal and learning indicator.
Read the complete comparison table
| Row | Related page | Why it helps |
|---|---|---|
| 1 | Health and Safety Performance Monitoring, Measuring, Review and Audit | Core performance management page. |
| 2 | Active and Reactive Monitoring | Explains monitoring types and assurance layers. |
| 3 | Health and Safety Auditing | Shows how audit evidence tests KPI quality. |
| 4 | Health and Safety Management Systems | Connects KPIs to the management system. |
| 5 | Incident Investigation and Root Cause Analysis | Turns lagging data into learning. |
| 6 | Near Miss | Important weak-signal and learning indicator. |
Official and primary source claim map
Table ID: kpi-s-official-source-map
Source: https://www.sharehub.ltd/knowledge-hub/kpi-s.html
Row 1
- Authority
HSE
- Source
HSE HSG65: Managing for health and safety
- Jurisdiction
Great Britain
- Decision
Management monitoring, review and worker involvement. Edition or update: Third edition 2013.
Row 2
- Authority
HSE
- Source
HSE: Check performance
- Jurisdiction
Great Britain
- Decision
Active and reactive monitoring and learning. Edition or update: Date not displayed.
Row 3
- Authority
HSE
- Source
HSE HSG254: Developing process safety indicators
- Jurisdiction
Great Britain
- Decision
Critical control and major hazard leading and lagging indicators. Edition or update: 2006.
Row 4
- Authority
HSE
- Source
HSE HSG245: Investigating accidents and incidents
- Jurisdiction
Great Britain
- Decision
Investigation and effective corrective action. Edition or update: Published 2004.
Row 5
- Authority
legislation.gov.uk
- Source
Health and Safety at Work etc. Act 1974
- Jurisdiction
Great Britain
- Decision
Great Britain general duties. Edition or update: 1974.
Row 6
- Authority
legislation.gov.uk
- Source
Management of Health and Safety at Work Regulations 1999
- Jurisdiction
Great Britain
- Decision
Great Britain management arrangements, assessment and review. Edition or update: 1999.
Row 7
- Authority
legislation.gov.uk
- Source
Health and Safety at Work (Northern Ireland) Order 1978
- Jurisdiction
Northern Ireland
- Decision
Northern Ireland general duties. Edition or update: 1978.
Row 8
- Authority
legislation.gov.uk
- Source
Management of Health and Safety at Work Regulations (NI) 2000
- Jurisdiction
Northern Ireland
- Decision
Northern Ireland assessment and management arrangements. Edition or update: 2000.
Row 9
- Authority
HSE
- Source
HSE: RIDDOR reportable incident types
- Jurisdiction
Great Britain
- Decision
Great Britain 2013 reporting categories and over-seven-day route. Edition or update: Current guidance.
Row 10
- Authority
HSENI
- Source
HSENI: Report an incident
- Jurisdiction
Northern Ireland
- Decision
Northern Ireland 1997 reporting categories and over-three-day route. Edition or update: Current guidance.
Row 11
- Authority
HSENI
- Source
HSENI: Co-operation and monitoring safe working
- Jurisdiction
Northern Ireland
- Decision
Northern Ireland reporting, supervision and monitoring of safe work. Edition or update: Date not displayed.
Row 12
- Authority
HSE
- Source
HSE health and safety management systems
- Jurisdiction
Great Britain
- Decision
Optional management-system scope, proportionate implementation, and why certification does not replace evidence of legal compliance.
Row 13
- Authority
HSE
- Source
HSE managing risk using PPE
- Jurisdiction
Great Britain; general hierarchy guidance
- Decision
Five-level hierarchy: elimination, substitution, engineering, administrative controls and PPE. Edition or update: Updated 21 January 2026.
Row 14
- Authority
HSE
- Source
HSE separating pedestrians and vehicles
- Jurisdiction
Great Britain
- Decision
Practical separation, barriers and crossing checks in the illustrative vehicle–pedestrian KPI. GB guidance, not a KPI percentage rule. Edition or update: Page dated 16 November 2021.
Row 15
- Authority
HSENI
- Source
HSENI Drive Danger Out — information for dutyholders
- Jurisdiction
Northern Ireland
- Decision
NI practical guidance on separating people and vehicles and managing crossings; not cited as the NI legal instrument. Edition or update: Publication or update date not displayed.
Read the complete comparison table
| Row | Authority | Source | Jurisdiction | Decision |
|---|---|---|---|---|
| 1 | HSE | HSE HSG65: Managing for health and safety | Great Britain | Management monitoring, review and worker involvement. Edition or update: Third edition 2013. |
| 2 | HSE | HSE: Check performance | Great Britain | Active and reactive monitoring and learning. Edition or update: Date not displayed. |
| 3 | HSE | HSE HSG254: Developing process safety indicators | Great Britain | Critical control and major hazard leading and lagging indicators. Edition or update: 2006. |
| 4 | HSE | HSE HSG245: Investigating accidents and incidents | Great Britain | Investigation and effective corrective action. Edition or update: Published 2004. |
| 5 | legislation.gov.uk | Health and Safety at Work etc. Act 1974 | Great Britain | Great Britain general duties. Edition or update: 1974. |
| 6 | legislation.gov.uk | Management of Health and Safety at Work Regulations 1999 | Great Britain | Great Britain management arrangements, assessment and review. Edition or update: 1999. |
| 7 | legislation.gov.uk | Health and Safety at Work (Northern Ireland) Order 1978 | Northern Ireland | Northern Ireland general duties. Edition or update: 1978. |
| 8 | legislation.gov.uk | Management of Health and Safety at Work Regulations (NI) 2000 | Northern Ireland | Northern Ireland assessment and management arrangements. Edition or update: 2000. |
| 9 | HSE | HSE: RIDDOR reportable incident types | Great Britain | Great Britain 2013 reporting categories and over-seven-day route. Edition or update: Current guidance. |
| 10 | HSENI | HSENI: Report an incident | Northern Ireland | Northern Ireland 1997 reporting categories and over-three-day route. Edition or update: Current guidance. |
| 11 | HSENI | HSENI: Co-operation and monitoring safe working | Northern Ireland | Northern Ireland reporting, supervision and monitoring of safe work. Edition or update: Date not displayed. |
| 12 | HSE | HSE health and safety management systems | Great Britain | Optional management-system scope, proportionate implementation, and why certification does not replace evidence of legal compliance. |
| 13 | HSE | HSE managing risk using PPE | Great Britain; general hierarchy guidance | Five-level hierarchy: elimination, substitution, engineering, administrative controls and PPE. Edition or update: Updated 21 January 2026. |
| 14 | HSE | HSE separating pedestrians and vehicles | Great Britain | Practical separation, barriers and crossing checks in the illustrative vehicle–pedestrian KPI. GB guidance, not a KPI percentage rule. Edition or update: Page dated 16 November 2021. |
| 15 | HSENI | HSENI Drive Danger Out — information for dutyholders | Northern Ireland | NI practical guidance on separating people and vehicles and managing crossings; not cited as the NI legal instrument. Edition or update: Publication or update date not displayed. |
terms
Table ID: kpi-s-terms
Source: https://www.sharehub.ltd/knowledge-hub/kpi-s.html
Row 1
- Term
KPI
- Meaning
Key performance indicator
- Use
Selected measure linked to an important risk decision
Row 2
- Term
LTIFR
- Meaning
Lost-time injury frequency rate
- Use
Lagging injury rate; definition and multiplier must be stated
Row 3
- Term
RIDDOR
- Meaning
Reporting of Injuries, Diseases and Dangerous Occurrences Regulations
- Use
GB 2013 and NI 1997 are different instruments
Row 4
- Term
OH&S
- Meaning
Occupational health and safety
- Use
Health and safety of people at work
Row 5
- Term
RAG
- Meaning
Red, amber, green
- Use
Status shorthand that needs a transparent threshold and action
Read the complete comparison table
| Row | Term | Meaning | Use |
|---|---|---|---|
| 1 | KPI | Key performance indicator | Selected measure linked to an important risk decision |
| 2 | LTIFR | Lost-time injury frequency rate | Lagging injury rate; definition and multiplier must be stated |
| 3 | RIDDOR | Reporting of Injuries, Diseases and Dangerous Occurrences Regulations | GB 2013 and NI 1997 are different instruments |
| 4 | OH&S | Occupational health and safety | Health and safety of people at work |
| 5 | RAG | Red, amber, green | Status shorthand that needs a transparent threshold and action |
Hierarchy of controls for Opening a conveyor guard for maintenance
Table ID: kpi-s-activity-control-hierarchy
Source: https://www.sharehub.ltd/knowledge-hub/kpi-s.html Scope: Teaching application; linked technical principles do not replace site-specific assessment or the GB/NI legal route.
Row 1
- Level
Eliminate
- Control
Move routine checks and lubrication points outside the guard so opening it is unnecessary.
- Verification
Machine owner confirms that inspection and lubrication can be completed outside the guarded area, including foreseeable faults and cleaning.
- Stop
If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
Row 2
- Level
Reduce, including substitution
- Control
Use a manufacturer-approved external inspection method or safely replaceable module where this reduces access to dangerous parts. Treat the design as an engineering control and retain isolation for intrusive work.
- Verification
Competent machine owner validates the external method or removable module against the manufacturer’s instructions; identify any work that still requires isolation.
- Stop
Reject an alternative if its performance is unproved or its new hazards are unresolved.
Row 3
- Level
Isolate
- Control
Stop and securely isolate all relevant energy sources; verify isolation and restrain parts or loads that could move.
- Verification
Supervisor checks the actual boundary, affected people and connected work; verify separation or isolation before allowing access.
- Stop
Hold or stop for uncertain isolation, retained motion, unsupported load or failed interlock.
Row 4
- Level
Control: physical safeguards
- Control
Restore suitable guards and interlocks after the repair and test the safety function before production release.
- Verification
Competent equipment/process owner checks energy sources, stored energy, guard fixings and interlock response.
- Stop
Hold or stop for uncertain isolation, retained motion, unsupported load or failed interlock.
Row 5
- Level
Control: work method and response
- Control
Identify the isolation boundary, affected contractors and restart owner; control any authorised diagnostic mode separately.
- Verification
Supervisor confirms the work limits, competent cover, communication and stop/restart authority with the people doing this activity.
- Stop
Hold work when the agreed limits, competent cover or effective communication cannot be maintained.
Row 6
- Level
PPE
- Control
Select task-assessed eye, hand and foot protection. Gloves must not create an entanglement risk near moving parts.
- Verification
Assessor confirms whether personal protection is needed and checks suitability, condition, compatibility and any required fit evidence.
- Stop
Do not use unsuitable protection or rely on PPE to continue after an essential source control fails.
Row 7
- Level
Discipline
- Control
Record guard defects, isolation removal and functional tests; do not close the job on paperwork alone.
- Verification
Release only after maintenance and operations agree the guarded restart. Retain verification and unresolved restrictions at handover.
- Stop
Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner.
Read the complete comparison table
| Row | Level | Control | Verification | Stop |
|---|---|---|---|---|
| 1 | Eliminate | Move routine checks and lubrication points outside the guard so opening it is unnecessary. | Machine owner confirms that inspection and lubrication can be completed outside the guarded area, including foreseeable faults and cleaning. | If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls. |
| 2 | Reduce, including substitution | Use a manufacturer-approved external inspection method or safely replaceable module where this reduces access to dangerous parts. Treat the design as an engineering control and retain isolation for intrusive work. | Competent machine owner validates the external method or removable module against the manufacturer’s instructions; identify any work that still requires isolation. | Reject an alternative if its performance is unproved or its new hazards are unresolved. |
| 3 | Isolate | Stop and securely isolate all relevant energy sources; verify isolation and restrain parts or loads that could move. | Supervisor checks the actual boundary, affected people and connected work; verify separation or isolation before allowing access. | Hold or stop for uncertain isolation, retained motion, unsupported load or failed interlock. |
| 4 | Control: physical safeguards | Restore suitable guards and interlocks after the repair and test the safety function before production release. | Competent equipment/process owner checks energy sources, stored energy, guard fixings and interlock response. | Hold or stop for uncertain isolation, retained motion, unsupported load or failed interlock. |
| 5 | Control: work method and response | Identify the isolation boundary, affected contractors and restart owner; control any authorised diagnostic mode separately. | Supervisor confirms the work limits, competent cover, communication and stop/restart authority with the people doing this activity. | Hold work when the agreed limits, competent cover or effective communication cannot be maintained. |
| 6 | PPE | Select task-assessed eye, hand and foot protection. Gloves must not create an entanglement risk near moving parts. | Assessor confirms whether personal protection is needed and checks suitability, condition, compatibility and any required fit evidence. | Do not use unsuitable protection or rely on PPE to continue after an essential source control fails. |
| 7 | Discipline | Record guard defects, isolation removal and functional tests; do not close the job on paperwork alone. | Release only after maintenance and operations agree the guarded restart. Retain verification and unresolved restrictions at handover. | Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner. |
Source tables and records 2
Monitoring responsibilities by role
Table ID: active-and-reactive-monitoring-role-routes
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Role
Workers and agency staff
- Decision and action
Check controls relevant to the task; report defects, near misses and symptoms; stop when a critical control is absent.
- Evidence or escalation
Tell the supervisor what was found, where and when; do not restart on assumption.
Row 2
- Role
Contractors and hosts
- Decision and action
Agree interface checks, permit or isolation conditions and who reports changes before starting.
- Evidence or escalation
Share inspection and hand-back evidence across the host-contractor boundary.
Row 3
- Role
Supervisors and maintainers
- Decision and action
Inspect the highest-risk controls, isolate unsafe equipment and verify repairs against the actual standard.
- Evidence or escalation
Record finding, interim protection, owner and authorisation to return to service.
Row 4
- Role
Managers and purchasers
- Decision and action
Resource controls and checks; select equipment and services that can be maintained and tested; act on trends.
- Evidence or escalation
Own overdue critical actions and record decisions, resources and effectiveness review.
Row 5
- Role
Safety advisers, occupational health and auditors
- Decision and action
Set competent methods, interpret technical data and challenge optimistic conclusions or biased sampling.
- Evidence or escalation
Report uncertainty, confidential health patterns and systemic failures through the right route.
Read the complete comparison table
| Row | Role | Decision and action | Evidence or escalation |
|---|---|---|---|
| 1 | Workers and agency staff | Check controls relevant to the task; report defects, near misses and symptoms; stop when a critical control is absent. | Tell the supervisor what was found, where and when; do not restart on assumption. |
| 2 | Contractors and hosts | Agree interface checks, permit or isolation conditions and who reports changes before starting. | Share inspection and hand-back evidence across the host-contractor boundary. |
| 3 | Supervisors and maintainers | Inspect the highest-risk controls, isolate unsafe equipment and verify repairs against the actual standard. | Record finding, interim protection, owner and authorisation to return to service. |
| 4 | Managers and purchasers | Resource controls and checks; select equipment and services that can be maintained and tested; act on trends. | Own overdue critical actions and record decisions, resources and effectiveness review. |
| 5 | Safety advisers, occupational health and auditors | Set competent methods, interpret technical data and challenge optimistic conclusions or biased sampling. | Report uncertainty, confidential health patterns and systemic failures through the right route. |
Active and reactive monitoring comparison
Table ID: active-and-reactive-monitoring-active-and-reactive-monitoring-comparison
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Monitoring type
Active monitoring
- Plain english meaning
Checking controls before harm occurs.
- Examples
Inspections, tours, audits, sampling, exposure monitoring, maintenance checks, permit checks and observations.
- Main question answered
Are the controls working now?
Row 2
- Monitoring type
Reactive monitoring
- Plain english meaning
Learning from events after something has gone wrong or nearly gone wrong.
- Examples
Accidents, near misses, ill-health cases, complaints, defects, enforcement, claims and investigations.
- Main question answered
What failed, why did it fail and what must change?
Row 3
- Monitoring type
Leading indicators
- Plain english meaning
Measures that give early warning about control health.
- Examples
Overdue actions, inspection quality, maintenance backlog, training refreshers, monitoring results and worker reports.
- Main question answered
Are weak signals appearing before harm occurs?
Row 4
- Monitoring type
Lagging indicators
- Plain english meaning
Measures of outcomes that have already happened.
- Examples
Injury rates, RIDDOR reports, occupational disease cases, absence, claims and damage.
- Main question answered
What harm or loss has already occurred?
Read the complete comparison table
| Row | Monitoring type | Plain english meaning | Examples | Main question answered |
|---|---|---|---|---|
| 1 | Active monitoring | Checking controls before harm occurs. | Inspections, tours, audits, sampling, exposure monitoring, maintenance checks, permit checks and observations. | Are the controls working now? |
| 2 | Reactive monitoring | Learning from events after something has gone wrong or nearly gone wrong. | Accidents, near misses, ill-health cases, complaints, defects, enforcement, claims and investigations. | What failed, why did it fail and what must change? |
| 3 | Leading indicators | Measures that give early warning about control health. | Overdue actions, inspection quality, maintenance backlog, training refreshers, monitoring results and worker reports. | Are weak signals appearing before harm occurs? |
| 4 | Lagging indicators | Measures of outcomes that have already happened. | Injury rates, RIDDOR reports, occupational disease cases, absence, claims and damage. | What harm or loss has already occurred? |
Active monitoring methods and practical use
Table ID: active-and-reactive-monitoring-active-monitoring-methods-and-practical-use
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Method
Workplace inspection
- What it checks
Physical conditions, housekeeping, equipment, access, storage, guards, signage and welfare.
- How to make it useful
Base frequency on risk, record defects clearly and verify completion.
Row 2
- Method
Safety tour
- What it checks
Leadership visibility, standards, behaviours and worker concerns.
- How to make it useful
Ask open questions and check whether workers understand controls.
Row 3
- Method
Audit
- What it checks
Whether management arrangements meet the intended standard and are implemented.
- How to make it useful
Use competent auditors and include sampling of real work, not only documents.
Row 4
- Method
Sampling and monitoring
- What it checks
Exposure, noise, vibration, air quality, water quality or other measurable conditions.
- How to make it useful
Target meaningful tasks and use results to improve controls.
Row 5
- Method
Behavioural observation
- What it checks
How work is actually done compared with the safe system.
- How to make it useful
Use it to understand system pressures, not to blame individuals.
Row 6
- Method
Action tracking
- What it checks
Whether findings are closed, late or recurring.
- How to make it useful
Require evidence of risk reduction, not simply an email saying action complete.
Read the complete comparison table
| Row | Method | What it checks | How to make it useful |
|---|---|---|---|
| 1 | Workplace inspection | Physical conditions, housekeeping, equipment, access, storage, guards, signage and welfare. | Base frequency on risk, record defects clearly and verify completion. |
| 2 | Safety tour | Leadership visibility, standards, behaviours and worker concerns. | Ask open questions and check whether workers understand controls. |
| 3 | Audit | Whether management arrangements meet the intended standard and are implemented. | Use competent auditors and include sampling of real work, not only documents. |
| 4 | Sampling and monitoring | Exposure, noise, vibration, air quality, water quality or other measurable conditions. | Target meaningful tasks and use results to improve controls. |
| 5 | Behavioural observation | How work is actually done compared with the safe system. | Use it to understand system pressures, not to blame individuals. |
| 6 | Action tracking | Whether findings are closed, late or recurring. | Require evidence of risk reduction, not simply an email saying action complete. |
Source comparison
Table ID: active-and-reactive-monitoring-ericpd-visual-controls
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Column 1
Eliminate
- Column 2
Design out access to the moving machine part.
- Column 3
Read the full task example, checks and stop points on this page.
Row 2
- Column 1
Reduce
- Column 2
Change the feed to avoid repeated hand entry.
- Column 3
Read the full task example, checks and stop points on this page.
Row 3
- Column 1
Isolate
- Column 2
Use suitable fixed or interlocked guarding.
- Column 3
Read the full task example, checks and stop points on this page.
Row 4
- Column 1
Control
- Column 2
Use authorised isolation and a defined exclusion zone.
- Column 3
Read the full task example, checks and stop points on this page.
Row 5
- Column 1
PPE
- Column 2
Gloves cannot make contact with moving parts safe.
- Column 3
Read the full task example, checks and stop points on this page.
Row 6
- Column 1
Discipline
- Column 2
Test safeguards, investigate bypasses and verify defect closure.
- Column 3
Read the full task example, checks and stop points on this page.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 |
|---|---|---|---|
| 1 | Eliminate | Design out access to the moving machine part. | Read the full task example, checks and stop points on this page. |
| 2 | Reduce | Change the feed to avoid repeated hand entry. | Read the full task example, checks and stop points on this page. |
| 3 | Isolate | Use suitable fixed or interlocked guarding. | Read the full task example, checks and stop points on this page. |
| 4 | Control | Use authorised isolation and a defined exclusion zone. | Read the full task example, checks and stop points on this page. |
| 5 | PPE | Gloves cannot make contact with moving parts safe. | Read the full task example, checks and stop points on this page. |
| 6 | Discipline | Test safeguards, investigate bypasses and verify defect closure. | Read the full task example, checks and stop points on this page. |
Active and reactive monitoring — ESEAP controls, task evidence and limits
Table ID: active-and-reactive-monitoring-ericpd-visual-controls-eseap
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Column 1
Elimination
- Column 2
Design out access to the moving machine part.
- Column 3
Read the full task example, checks and stop points on this page.
Row 2
- Column 1
Engineering controls
- Column 2
Change the feed to avoid repeated hand entry.
- Column 3
Read the full task example, checks and stop points on this page.
Row 3
- Column 1
Engineering controls / Administrative controls
- Column 2
Use suitable fixed or interlocked guarding.
- Column 3
Read the full task example, checks and stop points on this page.
Row 4
- Column 1
Engineering controls / Administrative controls
- Column 2
Use authorised isolation and a defined exclusion zone.
- Column 3
Read the full task example, checks and stop points on this page.
Row 5
- Column 1
PPE
- Column 2
Gloves cannot make contact with moving parts safe.
- Column 3
Read the full task example, checks and stop points on this page.
Row 6
- Column 1
Administrative controls
- Column 2
Test safeguards, investigate bypasses and verify defect closure.
- Column 3
Read the full task example, checks and stop points on this page.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 |
|---|---|---|---|
| 1 | Elimination | Design out access to the moving machine part. | Read the full task example, checks and stop points on this page. |
| 2 | Engineering controls | Change the feed to avoid repeated hand entry. | Read the full task example, checks and stop points on this page. |
| 3 | Engineering controls / Administrative controls | Use suitable fixed or interlocked guarding. | Read the full task example, checks and stop points on this page. |
| 4 | Engineering controls / Administrative controls | Use authorised isolation and a defined exclusion zone. | Read the full task example, checks and stop points on this page. |
| 5 | PPE | Gloves cannot make contact with moving parts safe. | Read the full task example, checks and stop points on this page. |
| 6 | Administrative controls | Test safeguards, investigate bypasses and verify defect closure. | Read the full task example, checks and stop points on this page. |
Active monitoring levels of assurance
Table ID: active-and-reactive-monitoring-active-monitoring-levels-of-assurance
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Assurance level
First line: frontline verification
- Who is typically involved
Workers, team leaders, supervisors, duty managers and task owners.
- What they check
Whether the controls needed for today’s work are present, understood and being used.
- Example evidence and top tip
Top tip: use mainly binary check sheets with specific yes/no questions. Has the worker completed training? Is the guard fitted? Is the permit authorised? Do workers know the new PPE rule? The value is in clean baseline data that can be compared between people, teams, shifts or sites.
Row 2
- Assurance level
Second line: leadership and specialist oversight
- Who is typically involved
Department managers, site leaders, HSSE advisers, occupational health, facilities, engineering, fire safety or topic specialists.
- What they check
Whether local checks are good enough, trends are understood, actions are prioritised and standards are applied consistently.
- Example evidence and top tip
Top tip: use repeatable themed checks that include documents, policies, procedures, records and field observation. Skilled reviewers should interpret findings, not just count answers. Quality matters more than quantity, and findings should be risk-ranked with verifiable actions.
Row 3
- Assurance level
Third line: independent internal audit
- Who is typically involved
The internal audit function, independent of management responsibility for the activity. Competent external providers can deliver this function under appropriate governance; separate client, insurer and certification audits are external assurance, not automatically the third line.
- What they check
Whether the management system and critical controls are suitable, implemented, effective and honestly reported.
- Example evidence and top tip
Top tip: build audits for the specific activity, site or topic. Use a strong audit plan and evidence-based sampling: witnessed work, interviews, policies, procedures, training records, maintenance logs, incident data and management-system records. Findings should be ranked and linked to verifiable corrective actions.
Row 4
- Assurance level
Escalation route
- Who is typically involved
Any level that finds a serious weakness.
- What they check
Whether findings are escalated according to potential harm and not hidden by local ownership.
- Example evidence and top tip
Top tip: define escalation thresholds before the check starts. A failed critical control, repeated no answer, overdue high-risk action or serious audit finding should trigger management review, temporary controls and named action ownership.
Row 5
- Assurance level
Feedback loop
- Who is typically involved
Managers, workers, safety representatives and action owners.
- What they check
Whether learning from assurance changes standards, training, procurement, maintenance, staffing or supervision.
- Example evidence and top tip
Top tip: use each level for a different kind of learning. First-line yes/no trends show consistency, second-line findings explain why gaps exist, and third-line audits test whether the whole assurance model is reliable.
Read the complete comparison table
| Row | Assurance level | Who is typically involved | What they check | Example evidence and top tip |
|---|---|---|---|---|
| 1 | First line: frontline verification | Workers, team leaders, supervisors, duty managers and task owners. | Whether the controls needed for today’s work are present, understood and being used. | Top tip: use mainly binary check sheets with specific yes/no questions. Has the worker completed training? Is the guard fitted? Is the permit authorised? Do workers know the new PPE rule? The value is in clean baseline data that can be compared between people, teams, shifts or sites. |
| 2 | Second line: leadership and specialist oversight | Department managers, site leaders, HSSE advisers, occupational health, facilities, engineering, fire safety or topic specialists. | Whether local checks are good enough, trends are understood, actions are prioritised and standards are applied consistently. | Top tip: use repeatable themed checks that include documents, policies, procedures, records and field observation. Skilled reviewers should interpret findings, not just count answers. Quality matters more than quantity, and findings should be risk-ranked with verifiable actions. |
| 3 | Third line: independent internal audit | The internal audit function, independent of management responsibility for the activity. Competent external providers can deliver this function under appropriate governance; separate client, insurer and certification audits are external assurance, not automatically the third line. | Whether the management system and critical controls are suitable, implemented, effective and honestly reported. | Top tip: build audits for the specific activity, site or topic. Use a strong audit plan and evidence-based sampling: witnessed work, interviews, policies, procedures, training records, maintenance logs, incident data and management-system records. Findings should be ranked and linked to verifiable corrective actions. |
| 4 | Escalation route | Any level that finds a serious weakness. | Whether findings are escalated according to potential harm and not hidden by local ownership. | Top tip: define escalation thresholds before the check starts. A failed critical control, repeated no answer, overdue high-risk action or serious audit finding should trigger management review, temporary controls and named action ownership. |
| 5 | Feedback loop | Managers, workers, safety representatives and action owners. | Whether learning from assurance changes standards, training, procurement, maintenance, staffing or supervision. | Top tip: use each level for a different kind of learning. First-line yes/no trends show consistency, second-line findings explain why gaps exist, and third-line audits test whether the whole assurance model is reliable. |
Reactive monitoring sources and learning value
Table ID: active-and-reactive-monitoring-reactive-monitoring-sources-and-learning-value
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Reactive source
Accidents and injuries
- What it can reveal
Where harm has occurred and which controls failed or were missing.
- Good management response
Investigate proportionately, support people affected and verify corrective actions.
Row 2
- Reactive source
Near misses
- What it can reveal
Events where controls failed but harm did not occur.
- Good management response
Treat high-potential near misses seriously and review similar tasks.
Row 3
- Reactive source
Ill-health reports
- What it can reveal
Early signs of exposure, stress, ergonomic harm or occupational disease.
- Good management response
Review risk assessment, monitoring, health surveillance and work design.
Row 4
- Reactive source
Complaints and concerns
- What it can reveal
Weak signals from workers, customers, contractors or the public.
- Good management response
Acknowledge, investigate and feed findings into inspection and review.
Row 5
- Reactive source
Defects and non-conformities
- What it can reveal
Equipment, procedure or management-system weakness.
- Good management response
Prioritise by potential harm and track recurring patterns.
Row 6
- Reactive source
Enforcement, claims or external findings
- What it can reveal
Serious weakness identified by regulators, insurers, clients or courts.
- Good management response
Escalate to leadership review and update arrangements across relevant areas.
Read the complete comparison table
| Row | Reactive source | What it can reveal | Good management response |
|---|---|---|---|
| 1 | Accidents and injuries | Where harm has occurred and which controls failed or were missing. | Investigate proportionately, support people affected and verify corrective actions. |
| 2 | Near misses | Events where controls failed but harm did not occur. | Treat high-potential near misses seriously and review similar tasks. |
| 3 | Ill-health reports | Early signs of exposure, stress, ergonomic harm or occupational disease. | Review risk assessment, monitoring, health surveillance and work design. |
| 4 | Complaints and concerns | Weak signals from workers, customers, contractors or the public. | Acknowledge, investigate and feed findings into inspection and review. |
| 5 | Defects and non-conformities | Equipment, procedure or management-system weakness. | Prioritise by potential harm and track recurring patterns. |
| 6 | Enforcement, claims or external findings | Serious weakness identified by regulators, insurers, clients or courts. | Escalate to leadership review and update arrangements across relevant areas. |
Leading and lagging indicator examples
Table ID: active-and-reactive-monitoring-leading-and-lagging-indicator-examples
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Indicator type
Leading indicator
- Useful examples
Critical inspections completed to quality standard, overdue high-risk actions, repeat defects, maintenance backlog, exposure monitoring trends.
- Weak version to avoid
Only counting how many inspections were done.
Row 2
- Indicator type
Leading indicator
- Useful examples
Training competence verified for high-risk tasks, permit quality scores, contractor non-conformance trends, control-check observations.
- Weak version to avoid
Counting attendance without checking competence.
Row 3
- Indicator type
Lagging indicator
- Useful examples
RIDDOR reports, lost-time injuries, occupational disease reports, high-potential near misses and serious property damage.
- Weak version to avoid
Reporting only headline accident rate without context.
Row 4
- Indicator type
Lagging indicator
- Useful examples
First-aid trends, symptoms, absence, complaints, claims, enforcement notices and repeated minor incidents.
- Weak version to avoid
Treating each event as isolated and missing patterns.
Row 5
- Indicator type
Balanced indicator set
- Useful examples
Combines control health, action quality, event learning and management review decisions.
- Weak version to avoid
A dashboard that is not discussed, challenged or acted on.
Read the complete comparison table
| Row | Indicator type | Useful examples | Weak version to avoid |
|---|---|---|---|
| 1 | Leading indicator | Critical inspections completed to quality standard, overdue high-risk actions, repeat defects, maintenance backlog, exposure monitoring trends. | Only counting how many inspections were done. |
| 2 | Leading indicator | Training competence verified for high-risk tasks, permit quality scores, contractor non-conformance trends, control-check observations. | Counting attendance without checking competence. |
| 3 | Lagging indicator | RIDDOR reports, lost-time injuries, occupational disease reports, high-potential near misses and serious property damage. | Reporting only headline accident rate without context. |
| 4 | Lagging indicator | First-aid trends, symptoms, absence, complaints, claims, enforcement notices and repeated minor incidents. | Treating each event as isolated and missing patterns. |
| 5 | Balanced indicator set | Combines control health, action quality, event learning and management review decisions. | A dashboard that is not discussed, challenged or acted on. |
Illustrative warehouse review: one working week
Table ID: monitoring-dashboard-context-table-1
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Column 1
No recorded injuries during the review week
- Column 2
Describes recorded outcomes only. Check reporting completeness and workload; it does not demonstrate that controls worked.
Row 2
- Column 1
A guard defect remains open; vehicle-route checks identify a damaged segregation barrier
- Column 2
These are failures of controls for active work, regardless of the injury count. Restrict the affected activity and assign restoration evidence.
Row 3
- Column 1
Workers report near misses at the crossing
- Column 2
Investigate conditions and reporting confidence. More reports can reflect better reporting as well as worsening exposure; interpret them with work observations.
Row 4
- Column 1
Review decision
- Column 2
Prioritise failed safeguards, verify the repairs and observe normal operation before closing actions. Compare later periods using the same definitions and relevant exposure information.
Read the complete comparison table
| Row | Column 1 | Column 2 |
|---|---|---|
| 1 | No recorded injuries during the review week | Describes recorded outcomes only. Check reporting completeness and workload; it does not demonstrate that controls worked. |
| 2 | A guard defect remains open; vehicle-route checks identify a damaged segregation barrier | These are failures of controls for active work, regardless of the injury count. Restrict the affected activity and assign restoration evidence. |
| 3 | Workers report near misses at the crossing | Investigate conditions and reporting confidence. More reports can reflect better reporting as well as worsening exposure; interpret them with work observations. |
| 4 | Review decision | Prioritise failed safeguards, verify the repairs and observe normal operation before closing actions. Compare later periods using the same definitions and relevant exposure information. |
Two action records: completion is different from verified effect
Table ID: monitoring-action-proof-table-1
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Column 1
Incomplete: keep the hold
- Column 2
A contractor visit is booked and the repair job is marked complete.
- Column 3
No recorded check against the pool’s defined water-quality acceptance criteria. The duty manager has no accepted hand-back: the area stays closed.
Row 2
- Column 1
Ready for authorised acceptance
- Column 2
The competent pool operator records the corrective work and verifies the relevant water results against the pool’s operating plan.
- Column 3
The authorised duty manager checks the test record, confirms the opening-check result and accepts the hand-back. Record the next operational check and reopen only within the accepted scope.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 |
|---|---|---|---|
| 1 | Incomplete: keep the hold | A contractor visit is booked and the repair job is marked complete. | No recorded check against the pool’s defined water-quality acceptance criteria. The duty manager has no accepted hand-back: the area stays closed. |
| 2 | Ready for authorised acceptance | The competent pool operator records the corrective work and verifies the relevant water results against the pool’s operating plan. | The authorised duty manager checks the test record, confirms the opening-check result and accepts the hand-back. Record the next operational check and reopen only within the accepted scope. |
Planning inspections sampling and tours
Table ID: active-and-reactive-monitoring-planning-inspections-sampling-and-tours
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Design factor
Frequency
- What good practice looks like
Set frequency by risk, rate of change, previous performance and legal or technical requirements.
- Evidence to keep
Inspection schedule with rationale and review date.
Row 2
- Design factor
Competence
- What good practice looks like
Use people who understand the hazards, controls and inspection standard.
- Evidence to keep
Inspector training, briefing and calibration records.
Row 3
- Design factor
Objectivity
- What good practice looks like
Build challenge into the process through cross-checks, independent audits or worker involvement.
- Evidence to keep
Audit allocation, peer review or safety representative notes.
Row 4
- Design factor
Checklist quality
- What good practice looks like
Focus on critical controls, not only easy housekeeping items.
- Evidence to keep
Controlled checklist with version, owner and risk-based questions.
Row 5
- Design factor
Responsibility
- What good practice looks like
Assign owners for findings and make escalation routes clear.
- Evidence to keep
Action tracker with owner, due date, priority and close-out evidence.
Row 6
- Design factor
Prioritisation
- What good practice looks like
Rank findings by potential harm, not by what is easiest to close.
- Evidence to keep
Risk-rated actions and senior escalation for overdue high-risk items.
Read the complete comparison table
| Row | Design factor | What good practice looks like | Evidence to keep |
|---|---|---|---|
| 1 | Frequency | Set frequency by risk, rate of change, previous performance and legal or technical requirements. | Inspection schedule with rationale and review date. |
| 2 | Competence | Use people who understand the hazards, controls and inspection standard. | Inspector training, briefing and calibration records. |
| 3 | Objectivity | Build challenge into the process through cross-checks, independent audits or worker involvement. | Audit allocation, peer review or safety representative notes. |
| 4 | Checklist quality | Focus on critical controls, not only easy housekeeping items. | Controlled checklist with version, owner and risk-based questions. |
| 5 | Responsibility | Assign owners for findings and make escalation routes clear. | Action tracker with owner, due date, priority and close-out evidence. |
| 6 | Prioritisation | Rank findings by potential harm, not by what is easiest to close. | Risk-rated actions and senior escalation for overdue high-risk items. |
Monitoring data quality checks
Table ID: active-and-reactive-monitoring-monitoring-data-quality-checks
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Data quality issue
Under-reporting
- Why it matters
Creates false confidence and hides weak signals.
- How to improve it
Simplify reporting, remove blame, give feedback and act visibly on reports.
Row 2
- Data quality issue
Poor definitions
- Why it matters
Makes departments record and compare events inconsistently.
- How to improve it
Define terms and train supervisors in classification.
Row 3
- Data quality issue
Action closure without evidence
- Why it matters
Allows risk to remain while the dashboard shows green.
- How to improve it
Require photographs, records, observation or effectiveness checks.
Row 4
- Data quality issue
Superficial inspections
- Why it matters
Generate activity without finding real control weakness.
- How to improve it
Calibrate inspectors and sample high-risk controls.
Row 5
- Data quality issue
No trend analysis
- Why it matters
Misses recurring defects or repeated minor events.
- How to improve it
Review patterns by location, task, contractor, cause and control type.
Row 6
- Data quality issue
No worker feedback
- Why it matters
Misses practical problems that records do not show.
- How to improve it
Include conversations, consultation and worker observations in monitoring.
Row 7
- Data quality issue
Incomparable rates or missing denominators
- Why it matters
Creates false trends when hours, headcount, contractor scope, time periods or missing records differ.
- How to improve it
Record numerator, denominator, population, period, inclusion rules and data completeness before comparison.
Read the complete comparison table
| Row | Data quality issue | Why it matters | How to improve it |
|---|---|---|---|
| 1 | Under-reporting | Creates false confidence and hides weak signals. | Simplify reporting, remove blame, give feedback and act visibly on reports. |
| 2 | Poor definitions | Makes departments record and compare events inconsistently. | Define terms and train supervisors in classification. |
| 3 | Action closure without evidence | Allows risk to remain while the dashboard shows green. | Require photographs, records, observation or effectiveness checks. |
| 4 | Superficial inspections | Generate activity without finding real control weakness. | Calibrate inspectors and sample high-risk controls. |
| 5 | No trend analysis | Misses recurring defects or repeated minor events. | Review patterns by location, task, contractor, cause and control type. |
| 6 | No worker feedback | Misses practical problems that records do not show. | Include conversations, consultation and worker observations in monitoring. |
| 7 | Incomparable rates or missing denominators | Creates false trends when hours, headcount, contractor scope, time periods or missing records differ. | Record numerator, denominator, population, period, inclusion rules and data completeness before comparison. |
GB and NI monitoring legal routes
Table ID: active-and-reactive-monitoring-gb-ni-duties
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Jurisdiction
Great Britain
- Legal route
Management Regulations 1999 regulations 3 and 5; Health and Safety at Work etc. Act 1974.
- Monitoring decision
Assess risks and maintain effective planning, control, monitoring and review of preventive measures. Official source
Row 2
- Jurisdiction
Northern Ireland
- Legal route
Management Regulations (NI) 2000 regulations 3 and 5; Health and Safety at Work (NI) Order 1978.
- Monitoring decision
Use the NI instrument for equivalent management arrangements and general duties. Official source
Row 3
- Jurisdiction
Great Britain RIDDOR
- Legal route
RIDDOR 2013 and current HSE reportability guidance.
- Monitoring decision
Exclude accident day; count consecutive weekends and rest days. Record work-related incapacity over three days; report over seven days within 15 days of the incident when criteria apply. Check other categories separately. Official source
Row 4
- Jurisdiction
Northern Ireland RIDDOR
- Legal route
RIDDOR (NI) 1997 as amended and HSENI reporting guidance.
- Monitoring decision
Exclude accident day; count consecutive weekends and rest days. Report work-related incapacity over three days within 10 days of the incident when criteria apply; use current HSENI forms and guidance. Official source NI day-count guidance
Row 5
- Jurisdiction
SHARE or company method
- Legal route
Risk-based inspection, action and review programme.
- Monitoring decision
Set local standards and escalation transparently; do not describe an internal target as law. Official source
Read the complete comparison table
| Row | Jurisdiction | Legal route | Monitoring decision |
|---|---|---|---|
| 1 | Great Britain | Management Regulations 1999 regulations 3 and 5; Health and Safety at Work etc. Act 1974. | Assess risks and maintain effective planning, control, monitoring and review of preventive measures. Official source |
| 2 | Northern Ireland | Management Regulations (NI) 2000 regulations 3 and 5; Health and Safety at Work (NI) Order 1978. | Use the NI instrument for equivalent management arrangements and general duties. Official source |
| 3 | Great Britain RIDDOR | RIDDOR 2013 and current HSE reportability guidance. | Exclude accident day; count consecutive weekends and rest days. Record work-related incapacity over three days; report over seven days within 15 days of the incident when criteria apply. Check other categories separately. Official source |
| 4 | Northern Ireland RIDDOR | RIDDOR (NI) 1997 as amended and HSENI reporting guidance. | Exclude accident day; count consecutive weekends and rest days. Report work-related incapacity over three days within 10 days of the incident when criteria apply; use current HSENI forms and guidance. Official source NI day-count guidance |
| 5 | SHARE or company method | Risk-based inspection, action and review programme. | Set local standards and escalation transparently; do not describe an internal target as law. Official source |
Source tables and records 3
Role-specific monitoring competence evidence and reassessment
Table ID: active-and-reactive-monitoring-training-evidence
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Role and learning
Workers: spot and report failed controls
- Practice on the actual task
Recognise a missing guard, ineffective extraction, near miss or symptom and use the escalation route.
- Competence evidence and record
Correct scenario response and observed reporting; induction or briefing record.
- Assessor and reassessment trigger
Supervisor checks after changed task, weak report or repeated defect.
Row 2
- Role and learning
Supervisors: inspect real work
- Practice on the actual task
Sample critical controls, talk with workers and stop or restrict unsafe work.
- Competence evidence and record
Observed inspection with evidence, priority and action owner.
- Assessor and reassessment trigger
Competent manager checks after missed critical defect, incident or new process.
Row 3
- Role and learning
Technical inspectors and occupational specialists
- Practice on the actual task
Choose valid tests and sampling for equipment, exposure or health within professional scope.
- Competence evidence and record
Traceable method, calibration, interpretation and uncertainty.
- Assessor and reassessment trigger
Relevant competent specialist peer checks after method, standard or exposure change.
Row 4
- Role and learning
Managers: use leading and lagging signals
- Practice on the actual task
Prioritise serious risk, challenge missing data and resource corrective action.
- Competence evidence and record
Management decision and field-verified close-out, not a dashboard alone.
- Assessor and reassessment trigger
Senior leader checks after trends, major changes or repeated non-closure.
Row 5
- Role and learning
Auditors and safety advisers: test assurance quality
- Practice on the actual task
Check whether inspections are objective, jurisdiction correct and linked to critical risks.
- Competence evidence and record
Sampled workface evidence, interviews and review of action effectiveness.
- Assessor and reassessment trigger
Independent competent reviewer checks after audit findings or a weak system signal.
Row 6
- Role and learning
Procurement and system owners: enable valid checks
- Practice on the actual task
Specify inspection access, monitoring capability, record quality and escalation rules.
- Competence evidence and record
Approved specifications and commissioning checks tied to risk.
- Assessor and reassessment trigger
Technical lead checks on new equipment, software, contractor or data source.
Read the complete comparison table
| Row | Role and learning | Practice on the actual task | Competence evidence and record | Assessor and reassessment trigger |
|---|---|---|---|---|
| 1 | Workers: spot and report failed controls | Recognise a missing guard, ineffective extraction, near miss or symptom and use the escalation route. | Correct scenario response and observed reporting; induction or briefing record. | Supervisor checks after changed task, weak report or repeated defect. |
| 2 | Supervisors: inspect real work | Sample critical controls, talk with workers and stop or restrict unsafe work. | Observed inspection with evidence, priority and action owner. | Competent manager checks after missed critical defect, incident or new process. |
| 3 | Technical inspectors and occupational specialists | Choose valid tests and sampling for equipment, exposure or health within professional scope. | Traceable method, calibration, interpretation and uncertainty. | Relevant competent specialist peer checks after method, standard or exposure change. |
| 4 | Managers: use leading and lagging signals | Prioritise serious risk, challenge missing data and resource corrective action. | Management decision and field-verified close-out, not a dashboard alone. | Senior leader checks after trends, major changes or repeated non-closure. |
| 5 | Auditors and safety advisers: test assurance quality | Check whether inspections are objective, jurisdiction correct and linked to critical risks. | Sampled workface evidence, interviews and review of action effectiveness. | Independent competent reviewer checks after audit findings or a weak system signal. |
| 6 | Procurement and system owners: enable valid checks | Specify inspection access, monitoring capability, record quality and escalation rules. | Approved specifications and commissioning checks tied to risk. | Technical lead checks on new equipment, software, contractor or data source. |
Official source register
Table ID: active-and-reactive-monitoring-official-source-register
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Authority
HSE
- Linked source
HSE HSG65 Managing for health and safety
- Jurisdiction
Great Britain
- Claim supported
Active/reactive methods, risk-based frequency, leadership and review. Guidance, not a fixed legal inspection timetable.
Row 2
- Authority
HSE
- Linked source
HSE How to manage health and safety
- Jurisdiction
Great Britain
- Claim supported
Plan, Do, Check, Act and monitoring of real controls. Use for GB management practice; check NI instrument separately.
Row 3
- Authority
HSE
- Linked source
HSE HSG245 Investigating accidents and incidents (2004 edition; verify current HSE listing)
- Jurisdiction
Great Britain
- Claim supported
Proportionate investigation and immediate, underlying and root causes. Retained copy cites superseded GB RIDDOR 1995 and over-three-day reporting; use current HSE RIDDOR page for law.
Row 4
- Authority
HSE
- Linked source
HSE RIDDOR reportable incidents
- Jurisdiction
Great Britain
- Claim supported
Current GB reportability, including over-seven-day report threshold and over-three-day recording. Do not apply GB thresholds to Northern Ireland.
Row 5
- Authority
HSENI
- Linked source
HSENI Report an incident
- Jurisdiction
Northern Ireland
- Claim supported
NI RIDDOR 1997 (as amended) reporting route and over-three-day injury rule. Check current NI forms and criteria; NI did not adopt the GB 2013 changes.
Row 6
- Authority
UK legislation
- Linked source
Management of Health and Safety at Work Regulations 1999 (Instrument 1999)
- Jurisdiction
Great Britain
- Claim supported
Regulations 3 and 5: assessment and effective planning, organisation, control, monitoring and review. Use current amended GB text.
Row 7
- Authority
UK legislation
- Linked source
Management of Health and Safety at Work Regulations (NI) 2000 (Instrument 2000)
- Jurisdiction
Northern Ireland
- Claim supported
Regulations 3 and 5: NI assessment and health and safety arrangements. Use current amended NI text.
Row 8
- Authority
UK legislation
- Linked source
Health and Safety at Work etc. Act 1974 (Instrument 1974)
- Jurisdiction
Great Britain
- Claim supported
General employer duties to employees and others. General duty; no universal inspection interval is set by this page.
Row 9
- Authority
UK legislation
- Linked source
Health and Safety at Work (Northern Ireland) Order 1978 (Instrument 1978)
- Jurisdiction
Northern Ireland
- Claim supported
NI general employer duties to employees and others. Use NI Order, not GB 1974 Act, for NI general-duty citation.
Row 10
- Authority
HSE
- Linked source
HSE Monitoring the control of exposure
- Jurisdiction
Great Britain
- Claim supported
Distinguishes exposure measurement, screening and personal air monitoring. Health surveillance is different from exposure monitoring.
Row 11
- Authority
HSE
- Linked source
HSE Health monitoring and support for workers
- Jurisdiction
Great Britain
- Claim supported
Early symptom reports and work-related musculoskeletal trends. MSD health monitoring is described as optional good practice, not a universal legal scheme.
Row 12
- Authority
HSE
- Linked source
HSE INDG417 Leading health and safety at work (Revision 1, 2013; live English page)
- Jurisdiction
Great Britain
- Claim supported
Director and board leadership of monitoring, management review and action ownership.
Row 13
- Authority
HSE
- Linked source
HSE Managing risks and risk assessment at work
- Jurisdiction
Great Britain
- Claim supported
Risk assessment, controls and review triggers. Use task-specific assessment, not a copied checklist.
Row 14
- Authority
HSE
- Linked source
HSE workplace injury definitions and formulae
- Jurisdiction
Great Britain
- Claim supported
Defines injury incidence and rate formulae, denominators and reporting caveats for comparable trend analysis. National rates do not prove that a particular site is controlled.
Row 15
- Authority
HSENI
- Linked source
HSENI accident reporting and over-three-day day count (Live accident-reporting guidance)
- Jurisdiction
Northern Ireland
- Claim supported
Excludes accident day, includes non-working days and gives the over-three-day report route and 10-day submission deadline. Do not apply this NI threshold in GB.
Row 16
- Authority
Health and Safety Executive
- Linked source
HSE COSHH and cleaners (Live guidance)
- Jurisdiction
Great Britain
- Claim supported
Live guidance
Row 17
- Authority
Health and Safety Executive
- Linked source
HSE Workplace transport safety (Live guidance)
- Jurisdiction
Great Britain
- Claim supported
Live guidance
Row 18
- Authority
HSE
- Linked source
HSE ISO 45001 management-system guidance
- Jurisdiction
Great Britain
- Claim supported
Official guidance: ISO 45001 certification is not generally required by health and safety law and cannot by itself prove site compliance.
Read the complete comparison table
| Row | Authority | Linked source | Jurisdiction | Claim supported |
|---|---|---|---|---|
| 1 | HSE | HSE HSG65 Managing for health and safety | Great Britain | Active/reactive methods, risk-based frequency, leadership and review. Guidance, not a fixed legal inspection timetable. |
| 2 | HSE | HSE How to manage health and safety | Great Britain | Plan, Do, Check, Act and monitoring of real controls. Use for GB management practice; check NI instrument separately. |
| 3 | HSE | HSE HSG245 Investigating accidents and incidents (2004 edition; verify current HSE listing) | Great Britain | Proportionate investigation and immediate, underlying and root causes. Retained copy cites superseded GB RIDDOR 1995 and over-three-day reporting; use current HSE RIDDOR page for law. |
| 4 | HSE | HSE RIDDOR reportable incidents | Great Britain | Current GB reportability, including over-seven-day report threshold and over-three-day recording. Do not apply GB thresholds to Northern Ireland. |
| 5 | HSENI | HSENI Report an incident | Northern Ireland | NI RIDDOR 1997 (as amended) reporting route and over-three-day injury rule. Check current NI forms and criteria; NI did not adopt the GB 2013 changes. |
| 6 | UK legislation | Management of Health and Safety at Work Regulations 1999 (Instrument 1999) | Great Britain | Regulations 3 and 5: assessment and effective planning, organisation, control, monitoring and review. Use current amended GB text. |
| 7 | UK legislation | Management of Health and Safety at Work Regulations (NI) 2000 (Instrument 2000) | Northern Ireland | Regulations 3 and 5: NI assessment and health and safety arrangements. Use current amended NI text. |
| 8 | UK legislation | Health and Safety at Work etc. Act 1974 (Instrument 1974) | Great Britain | General employer duties to employees and others. General duty; no universal inspection interval is set by this page. |
| 9 | UK legislation | Health and Safety at Work (Northern Ireland) Order 1978 (Instrument 1978) | Northern Ireland | NI general employer duties to employees and others. Use NI Order, not GB 1974 Act, for NI general-duty citation. |
| 10 | HSE | HSE Monitoring the control of exposure | Great Britain | Distinguishes exposure measurement, screening and personal air monitoring. Health surveillance is different from exposure monitoring. |
| 11 | HSE | HSE Health monitoring and support for workers | Great Britain | Early symptom reports and work-related musculoskeletal trends. MSD health monitoring is described as optional good practice, not a universal legal scheme. |
| 12 | HSE | HSE INDG417 Leading health and safety at work (Revision 1, 2013; live English page) | Great Britain | Director and board leadership of monitoring, management review and action ownership. |
| 13 | HSE | HSE Managing risks and risk assessment at work | Great Britain | Risk assessment, controls and review triggers. Use task-specific assessment, not a copied checklist. |
| 14 | HSE | HSE workplace injury definitions and formulae | Great Britain | Defines injury incidence and rate formulae, denominators and reporting caveats for comparable trend analysis. National rates do not prove that a particular site is controlled. |
| 15 | HSENI | HSENI accident reporting and over-three-day day count (Live accident-reporting guidance) | Northern Ireland | Excludes accident day, includes non-working days and gives the over-three-day report route and 10-day submission deadline. Do not apply this NI threshold in GB. |
| 16 | Health and Safety Executive | HSE COSHH and cleaners (Live guidance) | Great Britain | Live guidance |
| 17 | Health and Safety Executive | HSE Workplace transport safety (Live guidance) | Great Britain | Live guidance |
| 18 | HSE | HSE ISO 45001 management-system guidance | Great Britain | Official guidance: ISO 45001 certification is not generally required by health and safety law and cannot by itself prove site compliance. |
Acronyms and terminology
Table ID: active-and-reactive-monitoring-acronyms-and-terminology
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Acronym or term
HSG65
- What it means
HSE guidance on managing for health and safety.
- Why it matters
Provides the Plan, Do, Check, Act management framework.
Row 2
- Acronym or term
HSG245
- What it means
HSE guidance on investigating accidents and incidents.
- Why it matters
Supports reactive monitoring and root-cause learning.
Row 3
- Acronym or term
RIDDOR
- What it means
Reporting of Injuries, Diseases and Dangerous Occurrences Regulations.
- Why it matters
Relevant to certain reactive events that must be reported.
Row 4
- Acronym or term
KPI
- What it means
Key performance indicator.
- Why it matters
A measure used to track performance, which may be leading or lagging.
Row 5
- Acronym or term
Leading indicator
- What it means
A measure that gives early information about control health.
- Why it matters
Useful for acting before harm occurs.
Row 6
- Acronym or term
Lagging indicator
- What it means
A measure of harm, loss or failure that has already occurred.
- Why it matters
Useful for learning, but too late to prevent that event.
Row 7
- Acronym or term
PDCA
- What it means
Plan, Do, Check, Act.
- Why it matters
A management cycle used in HSG65 and management systems.
Row 8
- Acronym or term
RCA
- What it means
Root cause analysis.
- Why it matters
A method for understanding why an event happened beyond the immediate cause.
Read the complete comparison table
| Row | Acronym or term | What it means | Why it matters |
|---|---|---|---|
| 1 | HSG65 | HSE guidance on managing for health and safety. | Provides the Plan, Do, Check, Act management framework. |
| 2 | HSG245 | HSE guidance on investigating accidents and incidents. | Supports reactive monitoring and root-cause learning. |
| 3 | RIDDOR | Reporting of Injuries, Diseases and Dangerous Occurrences Regulations. | Relevant to certain reactive events that must be reported. |
| 4 | KPI | Key performance indicator. | A measure used to track performance, which may be leading or lagging. |
| 5 | Leading indicator | A measure that gives early information about control health. | Useful for acting before harm occurs. |
| 6 | Lagging indicator | A measure of harm, loss or failure that has already occurred. | Useful for learning, but too late to prevent that event. |
| 7 | PDCA | Plan, Do, Check, Act. | A management cycle used in HSG65 and management systems. |
| 8 | RCA | Root cause analysis. | A method for understanding why an event happened beyond the immediate cause. |
Individual editable BuildOut documents
Table ID: active-and-reactive-monitoring-buildout-documents
Source: https://www.sharehub.ltd/knowledge-hub/active-and-reactive-monitoring.html
Row 1
- Document
Inspection, audit and performance-review procedureBOUK-PRO-MON · Completed fictional example · v1.0
- Purpose
Plan risk-based monitoring, record evidence, track findings and evaluate recurring weaknesses.
- Editable download
Download DOCXRead preview
Row 2
- Document
Risk-based inspection and audit programmeBOUK-PLN-MON-01 · Completed fictional example · v2.2
- Purpose
Schedule assurance by risk, change and performance; distinguish statutory inspections.
- Editable download
Download DOCXRead preview
Row 3
- Document
Supervisor daily safe-start and close-down checkBOUK-CHK-MON-01 · Blank editable master · v1.0
- Purpose
Verify work-front controls, welfare, access and safe shutdown.
- Editable download
Download DOCXRead preview
Row 4
- Document
Site management-system and control-effectiveness auditBOUK-AUD-MON-01 · Blank editable master · v1.0
- Purpose
Test implementation through observation, worker discussion and evidence sampling.
- Editable download
Download DOCXRead preview
Row 5
- Document
Director safety visit and worker-engagement recordBOUK-FRM-MON-01 · Blank editable master · v1.0
- Purpose
Record site leadership observations, worker concerns and commitments.
- Editable download
Download DOCXRead preview
Row 6
- Document
Corrective/preventive action and effectiveness registerBOUK-REG-MON-01 · Blank register with separate fictional worked entries · v1.0
- Purpose
Assign risk-based actions, deadlines, escalation and evidence of durable closure.
- Editable download
Download XLSXRead preview
Row 7
- Document
Performance and management-review input packBOUK-FRM-MON-02 · Blank editable master · v1.0
- Purpose
Use leading/lagging indicators with meaningful denominators and narrative.
- Editable download
Download DOCXRead preview
Read the complete comparison table
| Row | Document | Purpose | Editable download |
|---|---|---|---|
| 1 | Inspection, audit and performance-review procedureBOUK-PRO-MON · Completed fictional example · v1.0 | Plan risk-based monitoring, record evidence, track findings and evaluate recurring weaknesses. | Download DOCXRead preview |
| 2 | Risk-based inspection and audit programmeBOUK-PLN-MON-01 · Completed fictional example · v2.2 | Schedule assurance by risk, change and performance; distinguish statutory inspections. | Download DOCXRead preview |
| 3 | Supervisor daily safe-start and close-down checkBOUK-CHK-MON-01 · Blank editable master · v1.0 | Verify work-front controls, welfare, access and safe shutdown. | Download DOCXRead preview |
| 4 | Site management-system and control-effectiveness auditBOUK-AUD-MON-01 · Blank editable master · v1.0 | Test implementation through observation, worker discussion and evidence sampling. | Download DOCXRead preview |
| 5 | Director safety visit and worker-engagement recordBOUK-FRM-MON-01 · Blank editable master · v1.0 | Record site leadership observations, worker concerns and commitments. | Download DOCXRead preview |
| 6 | Corrective/preventive action and effectiveness registerBOUK-REG-MON-01 · Blank register with separate fictional worked entries · v1.0 | Assign risk-based actions, deadlines, escalation and evidence of durable closure. | Download XLSXRead preview |
| 7 | Performance and management-review input packBOUK-FRM-MON-02 · Blank editable master · v1.0 | Use leading/lagging indicators with meaningful denominators and narrative. | Download DOCXRead preview |