Occupational asthma: prevention and early reporting · detailed source study
Optional reference study from the SHAREhub topic pages and selected source records used for this course. The core learning-time estimate excludes this extended reference.
What is occupational asthma and how does harm develop?
What is occupational asthma and how does harm develop?
Source: occupational-asthma--core
Occupational asthma is new asthma caused by workplace exposure. Most cases involve sensitisation to a respiratory sensitiser, or asthmagen; a substantial irritant exposure can cause a different work-related asthma pattern. Work-aggravated asthma means existing asthma is made worse by work and also needs a control response. HSE asthmagen guidance Learning point: Compare the named situations, controls and evidence together. GB HSE guidance applies to Great Britain; NI duties use HSENI and NI instruments. Clinical and research sources are scoped in the source register. Source basis: HSE: Asthma: an overview · HSE substances that can cause occupational asthma. Occupational asthma is new asthma caused by workplace exposure.
Most cases involve sensitisation to a respiratory sensitiser, or asthmagen; a substantial irritant exposure can cause a different work-related asthma pattern. Occupational asthma is new asthma caused by inhaling a respiratory sensitiser at work or, in some cases, by a high-level irritant exposure. Apply it: Which part of this plan would you check at the workface before authorising the task? Occupational asthma is new asthma caused by inhaling a respiratory sensitiser at work or, in some cases, by a high-level irritant exposure. Flour dust, isocyanate spray mist and other workplace agents can inflame and narrow the airways, with symptoms sometimes appearing after a shift. Treat as possible work-related pattern and refer.
Apply it: What evidence would show that the change improves this task, rather than only completing a record? Symptoms improve away from work: Treat as possible work-related pattern and refer. HSE FLOUR Open flour tipping: Review enclosed or low-dust transfer. HSE FLOUR Apply it: At which point would you hold this example, and what evidence would allow it to proceed? Exposure route 1: Flour or enzyme dust during tipping, mixing or dry cleaning Airborne particles enter the breathing zone; in susceptible people the airways may become sensitised and inflamed. Exposure route 2: Isocyanate-containing spray mist during coating or booth entry Fine mist reaches workers inside or outside a poorly controlled spray room; sensitisation can make later low exposures trigger asthma.
High-level irritant gas, vapour or fume release: A substantial acute inhalation can inflame airways without the usual sensitisation delay; clinical assessment determines the disease pattern. Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby? Elimination: Use a suitable supplied dough or a contained supply arrangement that removes local open bag emptying where feasible. Substitution: Validate a suitable low-dust flour or improver form while checking allergenic, skin, quality and process hazards. Engineering controls: Enclose or segregate charging and keep other workers away from the release; prevent dust spreading into clean work. Engineering controls: Provide effective capture and suitable mixer covers or contained charging; use dust-controlled cleaning instead of dry sweeping.
Administrative controls: Use a low-release charging method and realistic quantities; include maintenance, exposure review and required health surveillance in the plan. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged. Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk? Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status. Apply it: Which official source and full-topic section will you use to resolve the next decision?
Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links. Occupational asthma is new asthma caused by workplace exposure. Occupational asthma is new asthma caused by workplace exposure. Most cases involve sensitisation to a respiratory sensitiser, or asthmagen; a substantial irritant exposure can cause a different work-related asthma pattern. Occupational asthma is new asthma caused by inhaling a respiratory sensitiser at work or, in some cases, by a high-level irritant exposure. Apply it: Which part of this plan would you check at the workface before authorising the task? Use the evidence to improve the actual work arrangement.
Occupational asthma is new asthma caused by inhaling a respiratory sensitiser at work or, in some cases, by a high-level irritant exposure. Flour dust, isocyanate spray mist and other workplace agents can inflame and narrow the airways, with symptoms sometimes appearing after a shift. Treat as possible work-related pattern and refer. Apply it: What evidence would show that the change improves this task, rather than only completing a record? Fictional example: a practical application of the existing topic lesson. Symptoms improve away from work: Treat as possible work-related pattern and refer. HSE FLOUR Open flour tipping: Review enclosed or low-dust transfer. HSE FLOUR Apply it: At which point would you hold this example, and what evidence would allow it to proceed?
Connect the task, the route to the person and the control that can fail. Exposure route 1: Flour or enzyme dust during tipping, mixing or dry cleaning Airborne particles enter the breathing zone; in susceptible people the airways may become sensitised and inflamed. Exposure route 2: Isocyanate-containing spray mist during coating or booth entry Fine mist reaches workers inside or outside a poorly controlled spray room; sensitisation can make later low exposures trigger asthma. High-level irritant gas, vapour or fume release: A substantial acute inhalation can inflame airways without the usual sensitisation delay; clinical assessment determines the disease pattern. Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby? Start with the stronger practicable options and verify their effect.
Elimination: Use a suitable supplied dough or a contained supply arrangement that removes local open bag emptying where feasible. Substitution: Validate a suitable low-dust flour or improver form while checking allergenic, skin, quality and process hazards. Engineering controls: Enclose or segregate charging and keep other workers away from the release; prevent dust spreading into clean work. Engineering controls: Provide effective capture and suitable mixer covers or contained charging; use dust-controlled cleaning instead of dry sweeping. Administrative controls: Use a low-release charging method and realistic quantities; include maintenance, exposure review and required health surveillance in the plan. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.
Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk? Follow the official sources below and retain the task-specific evidence. Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status. Apply it: Which official source and full-topic section will you use to resolve the next decision? Simplified learning guide. Use the full topic and the actual work arrangements; existing technical-review and approval statuses still apply. Workplace scenarios labelled fictional are illustrative examples.
Flour dust, isocyanates, some wood dusts, solder flux fume, enzymes and animal allergens are examples of agents that need task-specific assessment. Inhaled material can inflame and narrow the bronchial airways. After sensitisation, a small later exposure may trigger cough, wheeze, chest tightness or breathlessness; symptoms can appear during a shift or hours later at night. A pattern that eases during weekends or holidays is a useful clue, but it is not a diagnosis and absence of that pattern does not rule work out. Nasal or eye irritation may appear early. Continued exposure after symptoms start can reduce the chance of recovery, so report the task and timing promptly, control exposure and seek clinical assessment. Severe breathing difficulty needs urgent help.
How do the lungs work, and how can workplace exposures affect breathing?
How do the lungs work, and how can workplace exposures affect breathing?
Source: occupational-asthma--anatomy-respiratory
Interactive anatomy · Respiratory tract and lungs · Updated 2026-10-23 Shows sensitisation and later airway narrowing; preserves the page distinction between occupational and work-aggravated asthma. A narrowed airway makes breathing harder. Contracted muscle, swelling and mucus can narrow the small airways and restrict airflow. A flour-handling locator connects the anatomy to prevention of workplace sensitiser exposure. The illustration cannot diagnose the cause of an individual's symptoms. Reduce or remove the dusty handling step, use a suitable closed process or source control and check effectiveness. Simplified mechanism; workplace symptoms need appropriate assessment and clinical advice. Source guidance: HSE guidance Call 999 for severe breathing difficulty, such as gasping, choking or being unable to get words out. Do not wait for this activity to finish.
Do not enter a contaminated or oxygen-deficient space to attempt an unprotected rescue. NHS: Shortness of breath · HSE: Asphyxiation hazards in welding and allied processes Follow air from the upper airway to the air sacs. Separate moving air from exchanging gases, then compare irritation, narrowed airways and two distinct scarring examples. Watch a workplace example Front teaching cutaway with patient right/left marked. Right lung: three lobes; left: two. Surrounding tissue is omitted to reveal the pathway. Separated teaching view · spacing is altered. Reassemble before following the process. The 2D diagram separates layers only; rotate controls apply to the 3D model. Reduced motion is enabled. Use the numbered steps as still explanations. The complete 2D lesson is ready.
Choose to rotate the original teaching model. Exposure example Structure 1 of 10 Air enters and leaves here. The nose and mouth connect the outside air with the respiratory passages. Air moves through these openings on both the inward and outward breath. Follow the route towards the windpipe before looking at the smaller branches. The illustrated flow is air, a mixture of gases, rather than pure oxygen passing directly into blood. Choose a still step or play the sequence. Illustrative timing; no measurement or personal assessment. Breathing in begins with a change in the space inside the chest. The diaphragm, a dome-shaped muscle beneath the lungs, contracts and moves downwards. Muscles around the ribs help lift the chest upwards and outwards.
As the lungs expand with this changing space, air can enter through the airways. Locate the diaphragm and rib cage together rather than treating the lungs as muscles that pull themselves open. The model separates the movement into a teaching step so you can follow its purpose. In the body, chest movement, airflow and blood circulation are connected parts of a continuing process. Learning activity only. These choices do not diagnose a condition or certify practical competence. Simplified education, not diagnosis, a lung-function or oxygen-saturation test, an exposure calculator or a fitness-to-work assessment. No breath-holding challenge, breathing-rate score or personal health-data collection. Ordinary particle filters do not protect against every gas or oxygen deficiency.
COPD and coal-dust topics may reuse normal anatomy only until separate mechanisms are reviewed. Air enters and leaves here. The nose and mouth connect the outside air with the respiratory passages. Air moves through these openings on both the inward and outward breath. Follow the route towards the windpipe before looking at the smaller branches. The illustrated flow is air, a mixture of gases, rather than pure oxygen passing directly into blood. Frimley Health NHS Foundation Trust: How your lungs work · Central and North West London NHS Foundation Trust: How do we breathe? The windpipe carries air into the chest. The trachea, commonly called the windpipe, carries air down towards the chest. It divides into the two main bronchi that supply the lungs.
Locate this shared passage before following either branch. Its role is to conduct air towards the gas-exchange regions and provide an outward route for the next exhalation. Frimley Health NHS Foundation Trust: How your lungs work A main branch carries air into each lung. The two main bronchi take air from the windpipe into the right and left lungs. They divide into progressively smaller branches, distributing the breath through the lungs. Use the split as a landmark before following one highlighted route. These are air passages, distinct from the blood vessels that run through the same organs. Frimley Health NHS Foundation Trust: How your lungs work · University Hospitals of North Midlands NHS Trust: My lung surgery: about your lungs Smaller branches distribute air.
Bronchioles are smaller branches of the airway system inside the lungs. Their branching routes lead towards clusters of alveoli, where the breath reaches the gas-exchange surface. Follow one branch to its end, using the others as context. This simplified route represents part of a much larger network supplying the lungs together. Frimley Health NHS Foundation Trust: How your lungs work Tiny air sacs provide a gas-exchange surface. Alveoli are tiny air sacs at the ends of the small airway routes. Their close relationship with surrounding capillaries allows oxygen to pass towards blood and carbon dioxide towards alveolar air. Connect the highlighted cluster with the enlarged gas-exchange view. The enlargement changes the scale so the air space and neighbouring blood vessel can be distinguished.
Frimley Health NHS Foundation Trust: How your lungs work · Central and North West London NHS Foundation Trust: How do we breathe? A thin boundary separates air from blood. The thin alveolar and capillary walls separate air in the sac from blood in its neighbouring vessel. Oxygen and carbon dioxide cross this boundary in opposite directions. Locate the tissue between the two spaces in the enlarged view. Blood cells remain in the vessel; the model does not represent an open connection through which air and blood mix. Central and North West London NHS Foundation Trust: How do we breathe? Small blood vessels pass beside the air sacs. Pulmonary capillaries are small blood vessels beside the alveoli.
Blood moving through them receives oxygen and releases carbon dioxide across the thin exchange boundary, then continues through the circulation. Follow the labelled gas routes separately from the blood cells. These cells stay inside the capillary rather than moving into the air sac. Central and North West London NHS Foundation Trust: How do we breathe? This muscle helps make room for a breath. The diaphragm is a broad, dome-shaped breathing muscle beneath the lungs. It contracts and flattens downwards during inhalation, helping increase the space in the chest. During a quiet exhalation it relaxes towards its dome shape. Compare it with the rib cage: their changing positions help move air without the lung tissue acting as a contracting muscle.
Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved Chest movement changes the space around the lungs. The rib cage protects the chest organs and moves with the breathing muscles. Expansion upwards and outwards helps increase chest space during inhalation; relaxation reduces that space during a quiet exhalation. Compare this movement with the diaphragm below the lungs. Together these structures provide the mechanics that allow air to move through the airways. Central and North West London NHS Foundation Trust: How do we breathe? · Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved Two thin layers surround the lungs and line the chest. The pleura has two thin layers around the lungs and inside the chest wall.
A small amount of fluid between them allows the surfaces to slide with less friction as breathing changes the chest space. Locate this outer covering separately from the internal air sacs; it is not the thin air–blood exchange boundary. Blackpool Teaching Hospitals NHS Foundation Trust: Pleural clinic Open the complete process transcript Breathing in begins with a change in the space inside the chest. The diaphragm, a dome-shaped muscle beneath the lungs, contracts and moves downwards. Muscles around the ribs help lift the chest upwards and outwards. As the lungs expand with this changing space, air can enter through the airways. Locate the diaphragm and rib cage together rather than treating the lungs as muscles that pull themselves open.
The model separates the movement into a teaching step so you can follow its purpose. In the body, chest movement, airflow and blood circulation are connected parts of a continuing process. Central and North West London NHS Foundation Trust: How do we breathe? · Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved What to watch: Locate the diaphragm beneath the lungs and the rib cage around them; compare their positions with the space occupied by the lungs. Why it matters: Changing the chest space draws air into the lung passages. The breathing muscles supply the movement, while the lungs expand with the chest to receive the next breath.
Explore this step: Select the diaphragm and rib cage in turn, then explain how their movement helps air enter without the lungs contracting like muscles. Air entering through the nose or mouth travels down the trachea, or windpipe, towards the chest. The trachea divides into the two main bronchi, with one route supplying each lung. Follow this continuous passage in the whole-chest view before moving into the smaller branches. The moving air is a mixture of gases, including oxygen; it is not a stream of pure oxygen travelling straight into the blood. These larger airways carry the breath towards the places where gas exchange happens. The same connected passages also provide the outward route when air is breathed out.
Frimley Health NHS Foundation Trust: How your lungs work What to watch: Start at the nose and mouth, follow the trachea downwards and find the split into the right and left main bronchi. Why it matters: The larger passages distribute air to both lungs and connect the outside air with the smaller branches inside. Gas exchange takes place further along the route, rather than within the windpipe. Explore this step: Trace the route to each lung and distinguish the tubes carrying air from the separate vessels carrying blood. Inside each lung, the bronchi divide into smaller branches called bronchioles. These passages distribute air towards clusters of tiny air sacs, the alveoli.
Follow one branch in the close-up and connect its end with an air-sac cluster, using the other branches as surrounding context. These routes distribute the breath throughout the lungs rather than supplying only one working air sac. A real lung contains many branching routes and air sacs operating together. This distribution brings air close to a large network of small blood vessels, preparing for the exchange shown in the next view. Frimley Health NHS Foundation Trust: How your lungs work What to watch: Follow one smaller airway to the cluster of air sacs at its end, keeping the other branches as surrounding context. Why it matters: Branching delivers air throughout the lungs instead of to one large chamber.
The many air sacs bring the inhaled gases close to blood vessels where oxygen and carbon dioxide can cross. Explore this step: Trace one complete branch to its air sacs, then explain how the many branches distribute air throughout the lungs. The lesson now changes from a branching airway to an enlarged air–blood interface. An alveolus contains air; beside it runs a capillary containing blood. Their very thin walls form the boundary across which gases can move. Locate the air space, the separating tissue and the inside of the vessel before following any gas symbols. The magnified view represents a tiny part of the same lung, not a separate organ or a hole that joins air and blood into one space.
The enlargement helps explain how the two systems can exchange gases while keeping their contents separate. Central and North West London NHS Foundation Trust: How do we breathe? What to watch: Find the air inside the enlarged alveolus, the thin separating boundary and the neighbouring capillary with blood cells inside it. Why it matters: A close boundary allows gases to cross between alveolar air and capillary blood. Keeping the two spaces separate lets ventilation and circulation cooperate without blood cells entering the air sac. Explore this step: Identify the air space and blood-vessel space, then point to the boundary each gas must cross between them. At the air–blood boundary, oxygen moves from the alveolar air into the capillary blood.
At the same time, carbon dioxide carried back from the body moves from the blood into the air sac. The two gases cross in opposite directions; blood cells stay within the vessel. Follow each labelled symbol separately so that exchanging gases is not confused with mixing the air and blood together. Blood then carries oxygen onwards towards the heart and the body’s tissues. The teaching symbols simplify continuous gas movement, and their size, colour and speed do not represent a measurement. Central and North West London NHS Foundation Trust: How do we breathe? What to watch: Follow the O₂ symbol towards the capillary and the CO₂ symbol towards the air sac, while locating the blood cells within the vessel.
Why it matters: Oxygen can be carried onwards for use by the body, while carbon dioxide returns to the airways for removal. Both transfers connect the breath with the continuing circulation of blood. Explore this step: Trace the two gas routes in opposite directions and explain why a blood cell should remain inside the capillary. During a quiet breath out, the diaphragm and other breathing muscles relax. The diaphragm returns towards its dome shape, chest space decreases and air moves back along the airways to the nose or mouth. This outgoing air carries carbon dioxide that crossed from the blood into the alveoli.
Trace the route in reverse without reversing the direction of blood circulation: oxygen-carrying blood continues towards the heart while another breath prepares to enter. The model presents a single cycle to explain the relationship. It does not show breathing as a series of separate events in which circulation stops between steps. Central and North West London NHS Foundation Trust: How do we breathe? · Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved What to watch: Compare the diaphragm and chest with the inhalation step, then follow the outward airway route from the lungs to the nose or mouth. Why it matters: Exhalation removes air containing carbon dioxide from gas exchange.
Meanwhile, blood circulation continues carrying oxygen onwards, linking this breathing cycle with the needs of the rest of the body. Explore this step: Trace the outward air route and the onward blood route separately, then describe why they are connected processes with different pathways. Sensitiser-related asthma Some people become sensitised to workplace substances such as flour or wood dust. Later exposure may trigger inflamed, narrowed airways, sometimes at low levels. Compare the airway opening, not the size of the whole lung. Sensitisation and later triggering are different phases, shown without a fixed clock. Work can also worsen existing asthma. Not all work-related asthma is an allergic reaction. A symptom pattern can prompt investigation but cannot establish a diagnosis from this model.
HSE: Asthma: an overview · NHS: Asthma · HSE: Flour dust and risks to bakers Assess sensitisers and maintain exposure controls Reduce dusty flour handling Get clinical advice about asthma symptoms Look at: The airway opening, its muscle and swollen lining. What changes: In asthma, narrowing, swelling and mucus can restrict the route for air. Why it matters: Breathing may become difficult, with wheeze, cough or chest tightness. What to do: Prevent exposure to the cause and report breathing symptoms for medical assessment. Bakery: flour is tipped and benches are dusted repeatedly during production. Time jump: sensitisation may develop over a variable period; a later exposure may trigger symptoms. This is not asthma developing in 32 seconds. Not every exposed or sensitised person develops asthma.
Wheeze or timing alone does not establish the cause or diagnosis. A dusty bakery task Flour is tipped into a mixer and used to dust the bench. Review low-dust ingredients and careful handling before relying on the worker to avoid a visible cloud. HSE: Flour dust and risks to bakers Repeated exposure, then a time jump Breathing flour dust can lead to sensitisation in some people over time. The timeline now jumps to a later contact after a hypersensitive state has developed in this chosen example. HSE: Asthma: an overview · HSE: Flour dust and risks to bakers A later contact can narrow airways The airway wall becomes inflamed and the breathing passage narrows in the illustrative asthma episode.
Symptoms may occur during the task or later; this is not the same as identifying asthma by a short animation. HSE: Asthma: an overview · NHS: Asthma Report patterns and reduce exposure Report work-related breathing problems promptly and obtain clinical advice. Review low-dust flour, transfer/handling and the full control assessment; use the emergency panel immediately for severe breathing difficulty. HSE: Advice for employers: occupational asthma · HSE: Flour dust and risks to bakers · NHS: Shortness of breath A team plans repeated concrete cuts with a handheld cut-off saw. Dust can enter the operator’s and nearby workers’ breathing zones. Open a window and use the same dry-cutting method. — A window alone does not control dust generated beside the face.
Choose task controls that prevent or capture it at source. First reduce the need to cut, then assess source suppression or extraction and any required suitable RPE. — This addresses the task before exposure occurs. Check that suppression or extraction works and that required RPE is suitable, fitted and used. Continue while nobody is coughing. — Symptoms are not an exposure monitor. Harmful respirable dust may be invisible, and a worker can feel well during exposure. A bakery worker notices repeated wheeze after dusty flour tasks, including some symptoms later in the evening. Report the pattern and seek medical and workplace assessment. — Reporting the pattern allows exposure controls and clinical assessment to be reviewed. Symptoms can be delayed; a clinician may need further investigation.
Use this model to diagnose occupational asthma. — The model explains a mechanism. It cannot diagnose asthma or establish that work caused it. Assume the task is safe if breathing improves away from work. — Improvement away from work may be useful information for investigation, but it does not show that returning to the same exposure is safe. One diagram shows a narrowed airway at LUN03–04. A second shows scarred gas-exchange tissue around LUN05–07. They show the same disease at successive stages. — Narrowed airways and scarred lung tissue are different changes. One is not automatically the next stage of the other. Both effects disappear when airborne dust settles. — Removing airborne dust does not reverse established fibrosis. Controlling further exposure remains important.
Airway narrowing and tissue fibrosis are different mechanisms. — Correct. Airway narrowing affects the passage for air; fibrosis affects lung tissue and its function. Neither picture supplies an individual diagnosis. The opening images are anatomical illustrations. The interactive 3D models and labelled SVG diagrams use original procedural artwork. These teaching images are not medical scans or diagnostic tools. Source references support the learner explanations and do not grant artwork rights. Asset and review record · Three.js MIT licence All anatomy, process and practice explanations remain available in the expandable reading sections. Interactive selection requires JavaScript. Call 999 for severe breathing difficulty, such as gasping, choking or being unable to get words out. Do not wait for this activity to finish.
Do not enter a contaminated or oxygen-deficient space to attempt an unprotected rescue. NHS: Shortness of breath · HSE: Asphyxiation hazards in welding and allied processes
How should COSHH control occupational asthma risk?
How should COSHH control occupational asthma risk?
Source: occupational-asthma--technical-model
Name the actual respiratory sensitiser and every task that releases it. A COSHH assessment that says only “dust” or “chemical” cannot distinguish flour, wood dust, isocyanate mist or an enzyme. Identify workers and others nearby, routine and maintenance work, skin and inhalation routes, control failures, symptoms and the product information needed to choose a safer method. Learning point: Compare the named situations, controls and evidence together. GB HSE guidance applies to Great Britain; NI duties use HSENI and NI instruments. Clinical and research sources are scoped in the source register. Source basis: HSE: Flour dust and risks to bakers · HSE 2-pack isocyanate paints · HSE substances that can cause occupational asthma. Learning point: Compare the named situations, controls and evidence together.
GB HSE guidance applies to Great Britain; NI duties use HSENI and NI instruments. Clinical and research sources are scoped in the source register. Source basis: HSE substances that can cause occupational asthma. Learning point: Compare the named situations, controls and evidence together. GB HSE guidance applies to Great Britain; NI duties use HSENI and NI instruments. Clinical and research sources are scoped in the source register. Source basis: HSE 2-pack isocyanate paints · HSE substances that can cause occupational asthma · HSE: Flour dust and risks to bakers. Use control hierarchy as a planning sequence, not a statute: eliminate the harmful step where feasible, reduce or substitute it, isolate it, then use engineering controls before administrative rules and RPE.
For a bakery, lower-dust flour and enclosed transfer can prevent a cloud at source; a disposable mask alone does not correct open tipping or dry sweeping. For isocyanate spraying, a properly designed booth, clearance control and air-fed protection are task-specific requirements that need competent verification. Health surveillance can detect early signs when workers remain exposed or likely to be exposed to asthmagens, but it does not capture airborne material. Work-linked symptoms, an abnormal surveillance finding or a control defect require an exposure and clinical response together. A competent occupational hygienist should decide whether sampling is needed and how results affect the control plan. For the actual task hazard, HSE places elimination first, then substitution, engineering controls, administrative controls and suitable PPE for residual risk.
Record why a higher control is not practicable and how the chosen measure is checked in use. HSE hierarchy of controls Use the HSE hierarchy for this task: eliminate the hazard where possible, substitute, use engineering controls, organise the work and use suitable PPE for residual risk. The exact choices require a task-specific assessment and competent verification. HSE hierarchy of controls Each row applies elimination, substitution, engineering, administrative checks and residual personal protection to the work hazard. The five HSE levels are elimination, substitution, engineering controls, administrative controls and PPE; supervision and inspection support the administrative arrangements. A higher control may be infeasible only after the specific task and alternative have been assessed.
How can bakery flour dust cause occupational asthma?
Source: occupational-asthma--worked-example
A bakery scenario shows why visible flour dust, cleaning methods and symptom patterns must be treated as control evidence. HSE FLOUR Learning point: Compare the named situations, controls and evidence together. Use the actual task assessment and the linked sources within their jurisdiction. Source basis: HSE: Flour dust and risks to bakers · HSE G402. Learning point: Compare the named situations, controls and evidence together. Use the actual task assessment and the linked sources within their jurisdiction. Source basis: HSE: Flour dust and risks to bakers · HSE G402. A bakery uses open flour tipping, hand dusting and dry sweeping at the end of the shift. A worker reports coughing and chest tightness on workdays, with improvement during a week away.
The supervisor says everyone coughs a bit around flour and issues a disposable mask. A competent response treats flour dust as an asthmagen. It reviews low-dust flour handling, enclosed tipping, dusting technique, LEV, cleaning with suitable vacuum rather than dry sweeping, RPE suitability, worker training, health surveillance and whether other workers have symptoms. The worker is signposted to OH or medical advice and unnecessary health details are kept out of ordinary manager records. The supervisor holds the dusty tipping and sweeping steps, checks the product and safety data, speaks privately with the affected worker and arranges prompt medical or occupational-health advice.
The bakery then trials low-dust flour, enclosed or low-drop transfer and suitable extraction, replaces dry sweeping with controlled cleaning, checks neighbouring workers and records who may restart each task. The flour workplace exposure limit in Great Britain is 10 mg/m³ over 8 hours and 30 mg/m³ over 15 minutes, but HSE says exposure to this asthmagen should be reduced as far below those limits as reasonably practicable; a number is not a safe target. Confirm the current limit and NI application before using it in a formal assessment. Before restart, a competent person confirms the controls work during real mixing and cleaning, the worker has a clear symptom-reporting route and the surveillance plan is appropriate.
A changed flour, enzyme additive, production rate or cleaning contractor triggers a fresh assessment and hand-back.
How do occupational asthma, work-aggravated asthma and irritant-induced asthma differ?
Source: occupational-asthma--asthma-types-boundary
The labels matter for clinical assessment, but managers should focus first on exposure control, work impact and early escalation. Occupational asthma may follow sensitisation to a workplace substance. After sensitisation, very low levels can trigger symptoms, so early reporting and exposure prevention matter. Work-aggravated asthma means existing asthma is worsened by work conditions. Irritant-induced asthma can follow a significant irritant exposure. A supervisor does not need to decide which label is correct before acting. If symptoms are linked to work, controls and health advice should be reviewed promptly. Common high-risk examples include flour dust, isocyanates, wood dust, solder or rosin fume, cleaning chemicals and laboratory animal allergens.
The distinction is clinically important because sensitiser-induced disease may follow a latency period, while irritant-induced disease can follow a substantial single event. The manager’s immediate decision is the same: prevent further uncontrolled exposure, record the actual task and agent, and refer for competent health assessment rather than assigning a label from one symptom pattern. Cough or irritation alone may not be asthma, but it is still a signal to examine a dusty or fume-producing task. A chlorine or ammonia release, for example, needs an incident response even when no sensitiser has been identified.
How do spirometry and serial peak-flow fit into the pathway?
Source: occupational-asthma--spirometry-peak-flow-context
Respiratory tests can support occupational-health assessment, but managers should not interpret them or delay exposure control while waiting for diagnosis. Spirometry can help assess lung function, and serial peak-flow records across work periods and rest days can help competent health professionals investigate whether symptoms follow a work-related pattern. These tools need proper instruction, interpretation and confidentiality. Early reporting matters because continued exposure after sensitisation can make asthma more severe, persistent or disabling. A worker with cough, wheeze, chest tightness or breathlessness linked to work should be removed from uncontrolled exposure and referred through the agreed OH or medical route while the COSHH controls are reviewed. Serial peak-flow measurements need a suitable work-and-rest pattern and interpretation by a clinician with occupational asthma expertise.
A normal single spirometry result or a worker feeling better on holiday does not prove the workplace safe. The employer remains responsible for making, maintaining and retaining the statutory health-surveillance record and permitted fitness outcomes. Confidential clinical notes and detailed tests stay with the OH professional; managers receive only necessary functional and control advice. Secure contracted storage can be used without transferring the employer’s responsibility. If temporary exposure restriction is advised, agree safe alternative work and a fair review route rather than asking the worker to prove a diagnosis first. For GB COSHH surveillance, keep the health record or a copy available for at least 40 years from its last entry. Define authorised access, worker access and provider-change transfer in the contract.
Clinical files transfer securely between OH providers, retaining medical confidence. HSE health-surveillance record keeping; COSHH regulation 11. Keep the separately cited NI statutory route and confirm its applicable record requirements.
What does occupational asthma control look like in spray painting?
What does occupational asthma control look like in spray painting?
Source: occupational-asthma--spray-painting-asthma-layer
Spray-painting controls need process containment, air-fed protection, clearance times, biological monitoring where relevant and health surveillance. In accident repair or coating work, isocyanate exposure can occur during mixing, spraying, curing, gun cleaning, booth entry and maintenance. Workers outside the booth can also be affected if clearance time or access control is weak. A good control standard covers product selection, booth airflow, LEV checks, air-fed RPE, face and air-supply checks, clearance time, cleaning method, health surveillance, biological monitoring timing where used and strict defect response. A spray booth has to be used for its assessed process, with a measured clearance time and controlled entry after spraying. A visor lifted before mist has cleared, a leaking booth or an unprotected cleaner can defeat the system.
HSE recommends biological monitoring for vehicle spray painters to check exposure control; the sampling method and timing need specialist advice and do not replace booth or health checks.
When should occupational asthma concerns be escalated?
Source: occupational-asthma--decision-tool
Escalation is needed when symptoms are linked to work, an asthmagen is uncontrolled, health surveillance raises concern, LEV or RPE fails, or a high-level irritant exposure occurs. HSE EMPLOYERS Workers should be encouraged to report early symptoms without fear of blame or job loss. Early removal from exposure or control improvement can make a major difference. Managers should use occupational health, occupational hygiene and competent COSHH advice rather than attempting to diagnose or handle respiratory disease informally. For a severe asthma attack or rapidly worsening breathing, use the emergency plan and urgent medical help. For new work-linked symptoms, stop uncontrolled exposure, seek prompt medical/OH assessment and investigate the task and other exposed workers.
Do not wait for a confirmed diagnosis before correcting a defective booth, extractor or cleaning method; do not let a general “mask available” sign justify restart. If the attack worsens, the reliever is not helping after its advised maximum, or no inhaler is available, call 999. Follow the person’s asthma plan and the call handler’s instructions; do not have the person drive themselves. Use current NHS asthma advice because reliever regimens differ. New work-pattern symptoms without emergency signs still need prompt clinical/OH advice and exposure-control review.
Where does occupational asthma prevention fail?
Source: occupational-asthma--failure-modes
Prevention fails when asthmagens are not identified, symptoms are normalised, and RPE or training is used instead of controlling exposure at source. A common failure is vague COSHH assessment. If the assessment says dust, fume or chemical but does not name the asthmagen, it is difficult to select controls or surveillance. Another failure is late response. Occupational asthma can worsen if exposure continues after symptoms appear. Early symptom reporting and fast control review should be built into training and supervision. A common near miss is treating early rhinitis or an evening cough as ordinary discomfort, especially when production still meets a dust or solvent target.
The response is to test the process and worker pathway: identify the agent, inspect extraction and enclosure during real work, ask whether symptoms relate to shifts, and close the cause rather than merely reminding the worker to wear RPE. Replace dry sweeping with controlled cleaning, check extraction during the real task, and feed surveillance findings back into control decisions.
How do exposure controls and health surveillance connect?
Source: occupational-asthma--control-surveillance-plan
Plan the surveillance response alongside exposure control, including symptoms reported between appointments. An occupational-health professional interprets health results; managers use the resulting work advice to correct the task. This SHARE planning aid follows HSE G402 for GB. Use HSENI's separate NI route with a competent provider. Surveillance can detect harm; it does not make poorly controlled exposure acceptable. HSE G402 · HSENI health surveillance. The provider decides the methods and frequency for the risk. A normal result is not permission to ignore control failures. Keep the existing urgent-care and GB/NI reporting routes available.
What evidence shows occupational asthma is being managed?
Source: occupational-asthma--evidence-pack
Good evidence shows that controls are planned, used, checked, corrected and reviewed. Evidence should match the actual asthmagen and task. Higher-exposure spraying, dusty mixing or maintenance needs a traceable assessment, verified engineering controls, suitable surveillance and a response to symptoms; a generic health campaign is not control evidence. Keep the product and task inventory, COSHH assessment, substitution decisions, LEV examination and maintenance, RPE selection and fit records, worker instruction, exposure monitoring where justified, and a restricted health-surveillance outcome and action trail. A manager should see the work restriction or control action needed, not an unnecessary clinical history. If one worker develops symptoms, compare the same task and controls for everyone exposed.
The record should show who owns each defect, when the correction is due, and what observed evidence closed it.
How should occupational asthma be assured?
Source: occupational-asthma--assurance
Assurance should test whether controls work in practice, not whether the page or procedure exists. Assurance should include frontline checks, manager review and periodic independent sampling where risk warrants it. The purpose is to find weak signals early, close actions properly and update the risk assessment when work changes. Sample actual mixing, spraying, cleaning and maintenance conditions, including shifts and contractors, against the written method. Check whether workers can report symptoms without retaliation, whether defects led to a hold, and whether the competent owner verified a correction before restart. A rising symptom pattern or repeated LEV fault should reach the manager who can change the process or fund replacement.
Senior leaders should see unresolved high-risk actions and resource decisions, while a competent specialist checks complex design, measurement or health-surveillance questions.
Which duties apply in Great Britain and Northern Ireland?
Source: occupational-asthma--legal-duties
Occupational asthma prevention rests on hazardous-substance assessment and control, suitable health surveillance where required, and prompt action on symptoms. Great Britain uses COSHH Regulations 2002 and RIDDOR 2013; Northern Ireland uses COSHH Regulations (NI) 2003 and RIDDOR (NI) 1997. Use the relevant regulator route for the work location. A workplace exposure limit (WEL) is not a target for a sensitiser. A manager should ask whether source controls keep exposure as low as reasonably practicable and whether a competent person has checked the actual task. Health surveillance detects possible harm; it is not permission to continue uncontrolled exposure. Reporting a diagnosed case is a separate decision from responding to symptoms and protecting colleagues. HSE EMPLOYERS HSENI COSHH
How should management arrangements verify controls?
Source: occupational-asthma--iso
Assign an owner, involve workers, check the control in use and act on failures before returning to routine work. HSE’s Plan, Do, Check, Act guidance provides the government management route for this topic. Apply it to the actual task, equipment, people and jurisdiction, then keep the verification and corrective-action record. Standards-specific claims are held until their rights and competent review are resolved. HSE Plan, Do, Check, Act
What training and competence are needed?
Source: occupational-asthma--training
Learning must match the task and the decision. A baker should demonstrate low-dust handling and a stop for failed extraction; a sprayer should know the assessed booth, air-fed protection and clearance rule; a supervisor must know how to hold work and seek competent health and hygiene advice. A general awareness session does not authorise those tasks. Assess performance on the actual method and keep an authorisation or competence record proportionate to risk. Reassess after a product or process change, a defect, symptoms or poor practice; do not invent a universal certificate expiry. Training supports source control and cannot compensate for a leaking booth or an open dusty process.
How could BuildOut Ltd manage this in practice?
How could BuildOut Ltd manage this in practice?
Source: occupational-asthma--business-example
BuildOut Ltd can manage occupational asthma by identifying asthmagens, controlling dust and fume at source, and responding quickly to symptom patterns. In this fictional contractor, workers may encounter wood dust, isocyanates, solder flux, cleaning chemicals and construction dust across changing sites. Before a joinery job, BuildOut Ltd identifies the wood species, cutting and sanding steps, other trades nearby and an extraction method. During work the supervisor checks the extractor and housekeeping; dust escaping into the shared corridor is a stop point. A cleaner or contractor must receive the same exposure information. At hand-back, the team checks the area, records any defect and refers work-linked symptoms through the clinical route while reviewing other exposed tasks. This is an illustrative company method, not a separate legal rule.
A baker tips flour and improver into a mixer. Include the bag-emptying, mixing and cleaning tasks and other people exposed to the flour cloud. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level. The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation"). ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.
What health boundary should readers understand?
Source: isocyanate-asthma--health-boundary
This page is workplace guidance, not medical diagnosis or treatment advice. This page is workplace guidance, not medical diagnosis or treatment advice. Isocyanate asthma is work-related asthma that can develop after exposure to reactive isocyanates in paints, coatings, foams or adhesives. Apply it: Which part of this plan would you check at the workface before authorising the task? Isocyanate asthma is work-related asthma that can develop after exposure to reactive isocyanates in paints, coatings, foams or adhesives. Spraying can create inhalable mist, while skin contact may also contribute to sensitisation. Keep product/SDS, substitution decision, booth test and clearance evidence, RPE/air-supply checks, biological-monitoring review, confidential health route and restart record.
Apply it: What evidence would show that the change improves this task, rather than only completing a record? During spraying and mist clearance, keep the air-fed protection on and the booth access controlled; do not lift the visor in the mist. A competent manager checks the fault and exposure pathway, arranges health advice for the worker, and restarts only after controls and clearance arrangements are verified. Apply it: At which point would you hold this example, and what evidence would allow it to proceed? Spraying or other isocyanate work can create airborne exposure. Inhaled material can cause sensitisation and occupational asthma. Symptoms and failed control signals need prompt action and the appropriate clinical route.
Use the full topic for the detailed mechanism, task limits and source scope. Apply it: Where is this harm route present in the actual work, and which control breaks it before anyone is exposed? Elimination: Use suitable prefinished parts or remove unnecessary spray refinishing where the job permits. Substitution: Validate a suitable isocyanate-free coating or non-spray process, checking performance and other hazards. Engineering controls: Restrict the spray area and prevent other workers entering during spraying and the verified clearance period. Engineering controls: Use a suitable maintained spray booth/room with effective extraction; verify containment and the measured clearance arrangement. Administrative controls: Follow the approved spraying and exit/entry procedure, keep required training current and arrange appropriate exposure monitoring and health surveillance.
Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged. Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk? Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status. Apply it: Which official source and full-topic section will you use to resolve the next decision? Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page.
Read the full topic for explanations, questions and source links. This page is workplace guidance, not medical diagnosis or treatment advice. This page is workplace guidance, not medical diagnosis or treatment advice. Isocyanate asthma is work-related asthma that can develop after exposure to reactive isocyanates in paints, coatings, foams or adhesives. Apply it: Which part of this plan would you check at the workface before authorising the task? Use the evidence to improve the actual work arrangement. Isocyanate asthma is work-related asthma that can develop after exposure to reactive isocyanates in paints, coatings, foams or adhesives. Spraying can create inhalable mist, while skin contact may also contribute to sensitisation.
Keep product/SDS, substitution decision, booth test and clearance evidence, RPE/air-supply checks, biological-monitoring review, confidential health route and restart record. Apply it: What evidence would show that the change improves this task, rather than only completing a record? Fictional example: a practical application of the existing topic lesson. During spraying and mist clearance, keep the air-fed protection on and the booth access controlled; do not lift the visor in the mist. A competent manager checks the fault and exposure pathway, arranges health advice for the worker, and restarts only after controls and clearance arrangements are verified. Apply it: At which point would you hold this example, and what evidence would allow it to proceed?
Connect the task, the route to the person and the control that can fail. Spraying or other isocyanate work can create airborne exposure. Inhaled material can cause sensitisation and occupational asthma. Symptoms and failed control signals need prompt action and the appropriate clinical route. Use the full topic for the detailed mechanism, task limits and source scope. Apply it: Where is this harm route present in the actual work, and which control breaks it before anyone is exposed? Start with the stronger practicable options and verify their effect. Elimination: Use suitable prefinished parts or remove unnecessary spray refinishing where the job permits. Substitution: Validate a suitable isocyanate-free coating or non-spray process, checking performance and other hazards.
Engineering controls: Restrict the spray area and prevent other workers entering during spraying and the verified clearance period. Engineering controls: Use a suitable maintained spray booth/room with effective extraction; verify containment and the measured clearance arrangement. Administrative controls: Follow the approved spraying and exit/entry procedure, keep required training current and arrange appropriate exposure monitoring and health surveillance. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged. Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk? Follow the official sources below and retain the task-specific evidence. Use the full topic for the decision points, practical examples, detailed control tables and source scope.
HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status. Apply it: Which official source and full-topic section will you use to resolve the next decision? Simplified learning guide. Use the full topic and the actual work arrangements; existing technical-review and approval statuses still apply. Workplace scenarios labelled fictional are illustrative examples. Managers should not diagnose asthma, decide that wheeze is unrelated to work or allow continued exposure after credible symptoms without review. Isocyanate sensitisation can have life-changing consequences, and early recognition matters.
Workers with chest tightness, wheeze, persistent cough, breathlessness or symptoms that appear after work, in the evening or early morning should report promptly and be signposted to occupational health or medical advice. Severe breathing difficulty should be handled through first-aid and emergency arrangements.
What are the key facts about isocyanate asthma?
What are the key facts about isocyanate asthma?
Source: isocyanate-asthma--key-facts
The key message is that sensitisation prevention must come before symptoms appear. An isocyanate product can be hazardous in a bodyshop, on a construction site or in a manufacturing task. A two-pack spray job needs product identification, a suitable booth, air-fed respiratory protection, clearance-time control and exposure/health checks. Symptoms can be delayed or improve away from work, so apparent recovery after a shift is not evidence that controls worked. See HSE - Isocyanates in construction; HSG276 - Isocyanate paint spraying.
What is isocyanate asthma in plain English?
Source: isocyanate-asthma--meaning
It is asthma caused by the immune system becoming sensitised to isocyanates at work. Isocyanates are chemicals used in many polyurethane-based products. They are found in 2-pack paints, vehicle refinishing, spray coatings, foams, adhesives, resins and some construction products. Exposure can occur through inhaling aerosol, vapour or mist, and through skin contact with some products. See HSE - Isocyanates in construction. Once a worker becomes sensitised, very small exposures may trigger asthma symptoms. This is why control cannot depend on whether the worker feels fine today. It must depend on preventing exposure, monitoring whether controls work and acting early on symptoms.
Where are isocyanate exposures found?
Source: isocyanate-asthma--exposure-sources
Isocyanates are not limited to vehicle paint shops; they appear across industries and products. The classic high-risk example is motor vehicle repair using 2K spray paints, but other exposures include construction spraying, floor screeds, adhesives, insulation foam, polyurethane manufacture, coatings, lacquers, resins and maintenance work on cured or uncured products. The risk is greatest where products are sprayed or heated, where ventilation is poor, where workers work close to the source, where bystanders are nearby, or where people clean spray guns and equipment without proper controls.
How does sensitisation happen?
Source: isocyanate-asthma--mechanism
Sensitisation means the body becomes unusually reactive after exposure. The mechanism matters because the first serious warning may not occur during the first exposure. A worker can become sensitised over time, then later react to very small amounts. Symptoms may appear after work or during the night, so workplaces must ask about timing and patterns, not only what happens during the shift. See HSE - Isocyanates in construction. Skin exposure may also matter. Poor glove selection, contaminated coveralls, poor cleaning and touching contaminated surfaces can contribute to overall risk and dermatitis.
How do the lungs work, and how can workplace exposures affect breathing?
Source: isocyanate-asthma--anatomy-respiratory
Interactive anatomy · Respiratory tract and lungs · Updated 2026-10-23 The inspected section explicitly explains sensitisation and later small exposures; no generic COPD or fibrosis representation. Call 999 for severe breathing difficulty, such as gasping, choking or being unable to get words out. Do not wait for this activity to finish. Do not enter a contaminated or oxygen-deficient space to attempt an unprotected rescue. NHS: Shortness of breath · HSE: Asphyxiation hazards in welding and allied processes Follow air from the upper airway to the air sacs. Separate moving air from exchanging gases, then compare irritation, narrowed airways and two distinct scarring examples. Watch a workplace example Front teaching cutaway with patient right/left marked. Right lung: three lobes; left: two.
Surrounding tissue is omitted to reveal the pathway. Separated teaching view · spacing is altered. Reassemble before following the process. The 2D diagram separates layers only; rotate controls apply to the 3D model. Reduced motion is enabled. Use the numbered steps as still explanations. The complete 2D lesson is ready. Choose to rotate the original teaching model. Exposure example Structure 1 of 10 Air enters and leaves here. The nose and mouth connect the outside air with the respiratory passages. Air moves through these openings on both the inward and outward breath. Follow the route towards the windpipe before looking at the smaller branches. The illustrated flow is air, a mixture of gases, rather than pure oxygen passing directly into blood.
Choose a still step or play the sequence. Illustrative timing; no measurement or personal assessment. Breathing in begins with a change in the space inside the chest. The diaphragm, a dome-shaped muscle beneath the lungs, contracts and moves downwards. Muscles around the ribs help lift the chest upwards and outwards. As the lungs expand with this changing space, air can enter through the airways. Locate the diaphragm and rib cage together rather than treating the lungs as muscles that pull themselves open. The model separates the movement into a teaching step so you can follow its purpose. In the body, chest movement, airflow and blood circulation are connected parts of a continuing process. Learning activity only.
These choices do not diagnose a condition or certify practical competence. Simplified education, not diagnosis, a lung-function or oxygen-saturation test, an exposure calculator or a fitness-to-work assessment. No breath-holding challenge, breathing-rate score or personal health-data collection. Ordinary particle filters do not protect against every gas or oxygen deficiency. COPD and coal-dust topics may reuse normal anatomy only until separate mechanisms are reviewed. Air enters and leaves here. The nose and mouth connect the outside air with the respiratory passages. Air moves through these openings on both the inward and outward breath. Follow the route towards the windpipe before looking at the smaller branches. The illustrated flow is air, a mixture of gases, rather than pure oxygen passing directly into blood.
Frimley Health NHS Foundation Trust: How your lungs work · Central and North West London NHS Foundation Trust: How do we breathe? The windpipe carries air into the chest. The trachea, commonly called the windpipe, carries air down towards the chest. It divides into the two main bronchi that supply the lungs. Locate this shared passage before following either branch. Its role is to conduct air towards the gas-exchange regions and provide an outward route for the next exhalation. Frimley Health NHS Foundation Trust: How your lungs work A main branch carries air into each lung. The two main bronchi take air from the windpipe into the right and left lungs. They divide into progressively smaller branches, distributing the breath through the lungs.
Use the split as a landmark before following one highlighted route. These are air passages, distinct from the blood vessels that run through the same organs. Frimley Health NHS Foundation Trust: How your lungs work · University Hospitals of North Midlands NHS Trust: My lung surgery: about your lungs Smaller branches distribute air. Bronchioles are smaller branches of the airway system inside the lungs. Their branching routes lead towards clusters of alveoli, where the breath reaches the gas-exchange surface. Follow one branch to its end, using the others as context. This simplified route represents part of a much larger network supplying the lungs together. Frimley Health NHS Foundation Trust: How your lungs work Tiny air sacs provide a gas-exchange surface.
Alveoli are tiny air sacs at the ends of the small airway routes. Their close relationship with surrounding capillaries allows oxygen to pass towards blood and carbon dioxide towards alveolar air. Connect the highlighted cluster with the enlarged gas-exchange view. The enlargement changes the scale so the air space and neighbouring blood vessel can be distinguished. Frimley Health NHS Foundation Trust: How your lungs work · Central and North West London NHS Foundation Trust: How do we breathe? A thin boundary separates air from blood. The thin alveolar and capillary walls separate air in the sac from blood in its neighbouring vessel. Oxygen and carbon dioxide cross this boundary in opposite directions. Locate the tissue between the two spaces in the enlarged view.
Blood cells remain in the vessel; the model does not represent an open connection through which air and blood mix. Central and North West London NHS Foundation Trust: How do we breathe? Small blood vessels pass beside the air sacs. Pulmonary capillaries are small blood vessels beside the alveoli. Blood moving through them receives oxygen and releases carbon dioxide across the thin exchange boundary, then continues through the circulation. Follow the labelled gas routes separately from the blood cells. These cells stay inside the capillary rather than moving into the air sac. Central and North West London NHS Foundation Trust: How do we breathe? This muscle helps make room for a breath. The diaphragm is a broad, dome-shaped breathing muscle beneath the lungs.
It contracts and flattens downwards during inhalation, helping increase the space in the chest. During a quiet exhalation it relaxes towards its dome shape. Compare it with the rib cage: their changing positions help move air without the lung tissue acting as a contracting muscle. Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved Chest movement changes the space around the lungs. The rib cage protects the chest organs and moves with the breathing muscles. Expansion upwards and outwards helps increase chest space during inhalation; relaxation reduces that space during a quiet exhalation. Compare this movement with the diaphragm below the lungs. Together these structures provide the mechanics that allow air to move through the airways.
Central and North West London NHS Foundation Trust: How do we breathe? · Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved Two thin layers surround the lungs and line the chest. The pleura has two thin layers around the lungs and inside the chest wall. A small amount of fluid between them allows the surfaces to slide with less friction as breathing changes the chest space. Locate this outer covering separately from the internal air sacs; it is not the thin air–blood exchange boundary. Blackpool Teaching Hospitals NHS Foundation Trust: Pleural clinic Open the complete process transcript Breathing in begins with a change in the space inside the chest.
The diaphragm, a dome-shaped muscle beneath the lungs, contracts and moves downwards. Muscles around the ribs help lift the chest upwards and outwards. As the lungs expand with this changing space, air can enter through the airways. Locate the diaphragm and rib cage together rather than treating the lungs as muscles that pull themselves open. The model separates the movement into a teaching step so you can follow its purpose. In the body, chest movement, airflow and blood circulation are connected parts of a continuing process.
Central and North West London NHS Foundation Trust: How do we breathe? · Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved What to watch: Locate the diaphragm beneath the lungs and the rib cage around them; compare their positions with the space occupied by the lungs. Why it matters: Changing the chest space draws air into the lung passages. The breathing muscles supply the movement, while the lungs expand with the chest to receive the next breath. Explore this step: Select the diaphragm and rib cage in turn, then explain how their movement helps air enter without the lungs contracting like muscles. Air entering through the nose or mouth travels down the trachea, or windpipe, towards the chest.
The trachea divides into the two main bronchi, with one route supplying each lung. Follow this continuous passage in the whole-chest view before moving into the smaller branches. The moving air is a mixture of gases, including oxygen; it is not a stream of pure oxygen travelling straight into the blood. These larger airways carry the breath towards the places where gas exchange happens. The same connected passages also provide the outward route when air is breathed out. Frimley Health NHS Foundation Trust: How your lungs work What to watch: Start at the nose and mouth, follow the trachea downwards and find the split into the right and left main bronchi.
Why it matters: The larger passages distribute air to both lungs and connect the outside air with the smaller branches inside. Gas exchange takes place further along the route, rather than within the windpipe. Explore this step: Trace the route to each lung and distinguish the tubes carrying air from the separate vessels carrying blood. Inside each lung, the bronchi divide into smaller branches called bronchioles. These passages distribute air towards clusters of tiny air sacs, the alveoli. Follow one branch in the close-up and connect its end with an air-sac cluster, using the other branches as surrounding context. These routes distribute the breath throughout the lungs rather than supplying only one working air sac.
A real lung contains many branching routes and air sacs operating together. This distribution brings air close to a large network of small blood vessels, preparing for the exchange shown in the next view. Frimley Health NHS Foundation Trust: How your lungs work What to watch: Follow one smaller airway to the cluster of air sacs at its end, keeping the other branches as surrounding context. Why it matters: Branching delivers air throughout the lungs instead of to one large chamber. The many air sacs bring the inhaled gases close to blood vessels where oxygen and carbon dioxide can cross. Explore this step: Trace one complete branch to its air sacs, then explain how the many branches distribute air throughout the lungs.
The lesson now changes from a branching airway to an enlarged air–blood interface. An alveolus contains air; beside it runs a capillary containing blood. Their very thin walls form the boundary across which gases can move. Locate the air space, the separating tissue and the inside of the vessel before following any gas symbols. The magnified view represents a tiny part of the same lung, not a separate organ or a hole that joins air and blood into one space. The enlargement helps explain how the two systems can exchange gases while keeping their contents separate. Central and North West London NHS Foundation Trust: How do we breathe?
What to watch: Find the air inside the enlarged alveolus, the thin separating boundary and the neighbouring capillary with blood cells inside it. Why it matters: A close boundary allows gases to cross between alveolar air and capillary blood. Keeping the two spaces separate lets ventilation and circulation cooperate without blood cells entering the air sac. Explore this step: Identify the air space and blood-vessel space, then point to the boundary each gas must cross between them. At the air–blood boundary, oxygen moves from the alveolar air into the capillary blood. At the same time, carbon dioxide carried back from the body moves from the blood into the air sac. The two gases cross in opposite directions; blood cells stay within the vessel.
Follow each labelled symbol separately so that exchanging gases is not confused with mixing the air and blood together. Blood then carries oxygen onwards towards the heart and the body’s tissues. The teaching symbols simplify continuous gas movement, and their size, colour and speed do not represent a measurement. Central and North West London NHS Foundation Trust: How do we breathe? What to watch: Follow the O₂ symbol towards the capillary and the CO₂ symbol towards the air sac, while locating the blood cells within the vessel. Why it matters: Oxygen can be carried onwards for use by the body, while carbon dioxide returns to the airways for removal. Both transfers connect the breath with the continuing circulation of blood.
Explore this step: Trace the two gas routes in opposite directions and explain why a blood cell should remain inside the capillary. During a quiet breath out, the diaphragm and other breathing muscles relax. The diaphragm returns towards its dome shape, chest space decreases and air moves back along the airways to the nose or mouth. This outgoing air carries carbon dioxide that crossed from the blood into the alveoli. Trace the route in reverse without reversing the direction of blood circulation: oxygen-carrying blood continues towards the heart while another breath prepares to enter. The model presents a single cycle to explain the relationship. It does not show breathing as a series of separate events in which circulation stops between steps.
Central and North West London NHS Foundation Trust: How do we breathe? · Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved What to watch: Compare the diaphragm and chest with the inhalation step, then follow the outward airway route from the lungs to the nose or mouth. Why it matters: Exhalation removes air containing carbon dioxide from gas exchange. Meanwhile, blood circulation continues carrying oxygen onwards, linking this breathing cycle with the needs of the rest of the body. Explore this step: Trace the outward air route and the onward blood route separately, then describe why they are connected processes with different pathways. Sensitiser-related asthma Some people become sensitised to workplace substances such as flour or wood dust.
Later exposure may trigger inflamed, narrowed airways, sometimes at low levels. Compare the airway opening, not the size of the whole lung. Sensitisation and later triggering are different phases, shown without a fixed clock. Work can also worsen existing asthma. Not all work-related asthma is an allergic reaction. A symptom pattern can prompt investigation but cannot establish a diagnosis from this model. HSE: Asthma: an overview · NHS: Asthma · HSE: Flour dust and risks to bakers Assess sensitisers and maintain exposure controls Reduce dusty flour handling Get clinical advice about asthma symptoms Look at: The airway opening, its muscle and swollen lining. What changes: In asthma, narrowing, swelling and mucus can restrict the route for air.
Why it matters: Breathing may become difficult, with wheeze, cough or chest tightness. What to do: Prevent exposure to the cause and report breathing symptoms for medical assessment. Bakery: flour is tipped and benches are dusted repeatedly during production. Time jump: sensitisation may develop over a variable period; a later exposure may trigger symptoms. This is not asthma developing in 32 seconds. Not every exposed or sensitised person develops asthma. Wheeze or timing alone does not establish the cause or diagnosis. A dusty bakery task Flour is tipped into a mixer and used to dust the bench. Review low-dust ingredients and careful handling before relying on the worker to avoid a visible cloud.
HSE: Flour dust and risks to bakers Repeated exposure, then a time jump Breathing flour dust can lead to sensitisation in some people over time. The timeline now jumps to a later contact after a hypersensitive state has developed in this chosen example. HSE: Asthma: an overview · HSE: Flour dust and risks to bakers A later contact can narrow airways The airway wall becomes inflamed and the breathing passage narrows in the illustrative asthma episode. Symptoms may occur during the task or later; this is not the same as identifying asthma by a short animation. HSE: Asthma: an overview · NHS: Asthma Report patterns and reduce exposure Report work-related breathing problems promptly and obtain clinical advice.
Review low-dust flour, transfer/handling and the full control assessment; use the emergency panel immediately for severe breathing difficulty. HSE: Advice for employers: occupational asthma · HSE: Flour dust and risks to bakers · NHS: Shortness of breath A team plans repeated concrete cuts with a handheld cut-off saw. Dust can enter the operator’s and nearby workers’ breathing zones. Open a window and use the same dry-cutting method. — A window alone does not control dust generated beside the face. Choose task controls that prevent or capture it at source. First reduce the need to cut, then assess source suppression or extraction and any required suitable RPE. — This addresses the task before exposure occurs.
Check that suppression or extraction works and that required RPE is suitable, fitted and used. Continue while nobody is coughing. — Symptoms are not an exposure monitor. Harmful respirable dust may be invisible, and a worker can feel well during exposure. A bakery worker notices repeated wheeze after dusty flour tasks, including some symptoms later in the evening. Report the pattern and seek medical and workplace assessment. — Reporting the pattern allows exposure controls and clinical assessment to be reviewed. Symptoms can be delayed; a clinician may need further investigation. Use this model to diagnose occupational asthma. — The model explains a mechanism. It cannot diagnose asthma or establish that work caused it.
Assume the task is safe if breathing improves away from work. — Improvement away from work may be useful information for investigation, but it does not show that returning to the same exposure is safe. One diagram shows a narrowed airway at LUN03–04. A second shows scarred gas-exchange tissue around LUN05–07. They show the same disease at successive stages. — Narrowed airways and scarred lung tissue are different changes. One is not automatically the next stage of the other. Both effects disappear when airborne dust settles. — Removing airborne dust does not reverse established fibrosis. Controlling further exposure remains important. Airway narrowing and tissue fibrosis are different mechanisms. — Correct. Airway narrowing affects the passage for air; fibrosis affects lung tissue and its function.
Neither picture supplies an individual diagnosis. The opening images are anatomical illustrations. The interactive 3D models and labelled SVG diagrams use original procedural artwork. These teaching images are not medical scans or diagnostic tools. Source references support the learner explanations and do not grant artwork rights. Asset and review record · Three.js MIT licence All anatomy, process and practice explanations remain available in the expandable reading sections. Interactive selection requires JavaScript. Call 999 for severe breathing difficulty, such as gasping, choking or being unable to get words out. Do not wait for this activity to finish. Do not enter a contaminated or oxygen-deficient space to attempt an unprotected rescue. NHS: Shortness of breath · HSE: Asphyxiation hazards in welding and allied processes
What symptoms should trigger action?
What symptoms should trigger action?
Source: isocyanate-asthma--symptoms
Symptoms should be treated as a possible control failure until competent review says otherwise. Wheeze, chest tightness, breathlessness, cough or a work-related pattern need prompt reporting and clinical or occupational-health assessment. Remove the worker from further exposure pending competent advice and investigate controls. HSE - Isocyanates in construction.
Why is spraying especially high risk?
Source: isocyanate-asthma--spraying
Spraying breaks liquid product into fine droplets that can travel, remain airborne and be inhaled. HSE guidance highlights that spraying can produce very high exposure because mist droplets are easily breathed in and because more product is used in a short time. Conventional spraying, HVLP and airless systems all have different overspray and injection hazards, so the equipment choice matters. See HSG276 - Isocyanate paint spraying; INDG388 - Safety in isocyanate paint spraying. The spray area must be managed as a contaminated atmosphere until it is clear. A worker who lifts an air-fed visor to inspect finish immediately after spraying can inhale mist despite having worn BA during the spraying pass.
How should COSHH assessment be carried out?
Source: isocyanate-asthma--assessment
A suitable COSHH assessment must identify the product, task, route, exposure group and control reliability. A weak assessment says 'wear mask'. A strong assessment identifies the isocyanate type, product use, spray method, booth or room condition, clearance time, RPE specification, breathing-air quality, bystander exposure, skin contact, cleaning work, maintenance and biological monitoring plan. See COSHH Regulations 2002; COSHH Regulations (Northern Ireland) 2003. Assessment must include foreseeable poor practice: rushing, lifting visors, cleaning guns, spraying small jobs outside a booth, allowing others into the area too early and failing to maintain air supply.
How should isocyanate exposure be controlled?
Source: isocyanate-asthma--controls
Controls should eliminate or minimise aerosol and skin exposure before relying on behaviour. Start with product and task assessment. Remove isocyanate spraying where feasible; otherwise combine verified booth extraction and clearance with protected spraying and exposure checks. The hierarchy table distinguishes engineering control from air-fed RPE. HSG276 - Isocyanate paint spraying. In a two-pack vehicle-paint job, the first choice is whether the finish can be achieved without isocyanate spray. If spraying remains necessary, the technical lead confirms the product and booth specification; the sprayer checks extraction and air supply before entry, keeps others out during the measured mist-clearance period and uses the specified air-fed protection. A failed booth test, unknown product or symptom report stops the task and triggers exposure review.
HSE HSG276 explains the spray-booth control approach.
What should be controlled around RPE, air-fed BA and spray booths?
Source: isocyanate-asthma--rpe
RPE is a life-critical control in isocyanate spraying and must be treated as a programme, not a mask purchase. For isocyanate paint spraying, ordinary filtering respirators are unsuitable. Select suitable air-fed breathing apparatus to the HSE task guidance, with assigned protection factor at least 20 and a low-flow indicator. A half-mask air-fed device in a spray room needs clear, continuing biological-monitoring evidence that exposure is adequately controlled; it is not the default choice. Verify manufacturer minimum flow, clean breathing-air quality, supply integrity and booth clearance before spraying and at use. HSG276 - Isocyanate paint spraying; HSG53 - Respiratory protective equipment at work.
HSE paint-spraying RPE guidance Tear-off visor covers, lighting, low-flow indicators, air-line checks and supervisor observation all matter because poor visibility or low air flow can tempt workers into unsafe behaviour.
How does biological monitoring help?
Source: isocyanate-asthma--monitoring
Biological monitoring checks whether exposure control is working in real people doing real tasks. HSE explains that urine biological monitoring can be used to check isocyanate exposure, especially where air-fed BA is relied on. This is valuable because booth, RPE and work-practice controls can all look acceptable but still fail in practice. See HSE - Biological monitoring and paint spraying. Results should be interpreted by competent people and used to improve controls. Biological monitoring is not a blame tool; it is a reality check on the system. Use a laboratory/competent adviser to select analysis for the actual isocyanates, sample representative work at the end of potential exposure within about an hour, and document product, task, sampling time and RPE/work conditions.
Interpret results competently, investigate controls where exposure is indicated and repeat testing after corrective action when indicated. HSE recommends annual monitoring for vehicle spray painters; frequency for other work follows its assessment. An exposure test does not diagnose asthma or clear a symptomatic worker to remain exposed. Normal urine results do not override symptoms, and staying below a WEL alone does not adequately control every sensitiser risk. Biological monitoring, airborne measurement and clinical health surveillance answer different questions. HSE: isocyanate sampling and interpretation
What health surveillance is needed?
Source: isocyanate-asthma--surveillance
Health surveillance helps detect early signs of occupational asthma and dermatitis. HSE guidance for isocyanate-exposed workers highlights respiratory health surveillance, including lung function testing and questionnaires, and skin surveillance where dermatitis risk exists. Surveillance should start early for new workers and continue periodically. See HSE - Health surveillance in motor vehicle repair. Health surveillance does not replace exposure control. If surveillance finds symptoms, the correct response is to protect the worker and investigate exposure, not simply repeat the test later.
How does isocyanate asthma appear in real workplaces?
Source: isocyanate-asthma--scenarios
Worked scenarios help supervisors recognise exposure failure before permanent disease develops. Compare the spray setup, bystander entry and symptom report in each scenario. The decision is whether exposure prevention is working now, who can hold the task, and what evidence permits restart.
How should a 2K spray-painting job be controlled from start to finish?
Source: isocyanate-asthma--spray-painting-example
A detailed bodyshop example shows how exposure control depends on every stage, not only the few minutes of spraying. Consider a vehicle repair task where a panel beater prepares a repaired door and wing, mixes a 2K coating, sprays primer and topcoat, allows the finish to cure, cleans the gun and then polishes the job. The isocyanate risk is not limited to the spray trigger being pulled. Exposure can occur during mixing, spraying, mist clearance, visor lifting, cleaning, handling contaminated surfaces and allowing other workers into the booth too early. See HSG276 - Isocyanate paint spraying. The control plan should therefore cover the whole job sequence.
The product should be identified from the safety data sheet, the booth should be checked before work, the air-fed breathing apparatus should be checked and worn correctly, the clearance time should be known, biological monitoring should be timed so it reflects real exposure, and health surveillance should ask about delayed symptoms such as night-time wheeze or chest tightness after spraying days.
What records prove isocyanate asthma risk is managed?
Source: isocyanate-asthma--records
Records should show assessment, control, monitoring, health surveillance and action. Records should prove that controls were selected, implemented, checked and improved. The table helps distinguish useful evidence from records that exist only because someone expected a document.
Which legal duties apply to isocyanate asthma?
Source: isocyanate-asthma--legal
A two-pack paint task falls under the hazardous-substance route for the work location: Great Britain’s COSHH 2002 or Northern Ireland’s COSHH guidance and 2003 regulations. The assessment must address the product, spray mist, skin contact, bystanders, extraction and health effects. HSE HSG276 is task guidance for spray booths; it is not a replacement for either jurisdiction’s law. A symptom report triggers prompt exposure review and suitable clinical referral, while any statutory occupational-disease report is a separate decision under the relevant GB or NI reporting rules. The supervisor should preserve the product identity, booth and air-supply checks, clearance-time evidence and the worker’s exposure history without putting private health details into a general team log.
How could BuildOut Ltd manage this in practice?
How could BuildOut Ltd manage this in practice?
Source: isocyanate-asthma--business-example
BuildOut Ltd would manage isocyanate asthma through product control, COSHH assessment, exclusion, RPE, monitoring and health surveillance. BuildOut Ltd is a fictional contractor with maintenance workshops, coating works and occasional spray tasks. It needs to prevent small jobs and contractor work from bypassing the controls used in formal spray operations.
How can the hierarchy of controls reduce risks while spraying a vehicle with isocyanate-containing paint?
Source: isocyanate-asthma--control-hierarchy
For two-pack vehicle spraying, first test whether the coating or application method can avoid isocyanate aerosol. Where spraying remains, verify booth extraction, clearance and suitable air-fed respiratory protection; stop for failed controls or symptoms. A bodyshop sprays a 2-pack coating. Water-based does not establish that a paint is isocyanate-free; identify the actual formulation and the full spraying and clearance task. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level. The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation"). ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE.
Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.
What training supports isocyanate asthma prevention?
Source: isocyanate-asthma--training
A sprayer’s competence must be observed across product selection, booth operation, respiratory protection, cleaning and symptom response, not inferred from course attendance. Sprayers must demonstrate product checks, booth and air supply checks, correct air-fed respiratory protection, the full mist and clearance-time rule, cleaning and symptom reporting. Supervisors must hold work for failed extraction or unknown product and arrange competent exposure and health advice. A practical observed spray task, biological-monitoring review and follow-up after a symptom report provide stronger evidence than course attendance.
How should management check and improve these controls?
Source: isocyanate-asthma--iso
HSE’s Plan, Do, Check, Act approach helps an organisation plan controls, put them into use, check performance and correct failures. It is management guidance, not a substitute for the GB or Northern Ireland legal duties that apply to the task. Link product identity, spray control, booth testing, respiratory protection, biological monitoring and symptoms to corrective action. Stop spray work when control evidence fails. HSE management guidance
What warning signs show isocyanate controls are weak?
Source: isocyanate-asthma--warning-signs
Warning signs include symptoms, visor lifting, unknown products, no monitoring and weak booth control. A spray-booth fault, visor lift, missing clearance-time evidence or work-related wheeze requires the supervisor to stop exposure, protect bystanders and arrange appropriate health advice. Reopen only after the product, booth, air supply and method have been checked.
Two-pack spray paint repair in a bodyshop
Source: isocyanate-asthma--example--isoas-scenario-001
Task Material And Setting: A painter prepares a vehicle panel for two-pack isocyanate paint in an enclosed spray booth; a neighbouring worker may enter during booth clearance. People And Prerequisites: The supervisor confirms product identity and safety data, spray method, booth flow/clearance time, air supply, sprayer competence and bystander exclusion. Before: Before spraying, consider an isocyanate-free coating or non-spray method if the specification permits; otherwise verify booth extraction, air-fed respiratory protection and the task COSHH assessment. During: During spraying and mist clearance, keep the air-fed protection on and the booth access controlled; do not lift the visor in the mist.
Hold Or Stop: Stop if booth flow or supplied air fails, the product is unknown, a bystander enters, the visor is lifted in mist or symptoms are reported. Completion And Hand Back: A competent manager checks the fault and exposure pathway, arranges health advice for the worker, and restarts only after controls and clearance arrangements are verified. Evidence: Keep product/SDS, substitution decision, booth test and clearance evidence, RPE/air-supply checks, biological-monitoring review, confidential health route and restart record.
Source tables and records 1
Work exposure and asthma harm mechanisms
Table ID: occupational-asthma-harm-mechanisms
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Source and task
Flour or enzyme dust during tipping, mixing or dry cleaning
- Route and body effect
Airborne particles enter the breathing zone; in susceptible people the airways may become sensitised and inflamed.
- Outcome and warning
Rhinitis, cough, wheeze or chest tightness may precede persistent asthma; symptoms can appear after work.
- Stop or escalate
Visible dust, work-linked symptoms or failed extraction: stop dusty handling, control the release and arrange prompt clinical/OH advice.
Row 2
- Source and task
Isocyanate-containing spray mist during coating or booth entry
- Route and body effect
Fine mist reaches workers inside or outside a poorly controlled spray room; sensitisation can make later low exposures trigger asthma.
- Outcome and warning
Evening or night symptoms, worsening reliever use or surveillance changes may signal disease; ongoing exposure can leave lasting impairment.
- Stop or escalate
Spray outside the assessed booth, ineffective extraction, premature entry or symptoms: stop exposure and get competent booth and health review.
Row 3
- Source and task
High-level irritant gas, vapour or fume release
- Route and body effect
A substantial acute inhalation can inflame airways without the usual sensitisation delay; clinical assessment determines the disease pattern.
- Outcome and warning
Immediate breathing symptoms may be serious; later persistent asthma is possible after a major exposure.
- Stop or escalate
Evacuate or isolate by the emergency plan, obtain urgent medical help for severe breathing difficulty and do not restart before investigation.
Read the complete comparison table
| Row | Source and task | Route and body effect | Outcome and warning | Stop or escalate |
|---|---|---|---|---|
| 1 | Flour or enzyme dust during tipping, mixing or dry cleaning | Airborne particles enter the breathing zone; in susceptible people the airways may become sensitised and inflamed. | Rhinitis, cough, wheeze or chest tightness may precede persistent asthma; symptoms can appear after work. | Visible dust, work-linked symptoms or failed extraction: stop dusty handling, control the release and arrange prompt clinical/OH advice. |
| 2 | Isocyanate-containing spray mist during coating or booth entry | Fine mist reaches workers inside or outside a poorly controlled spray room; sensitisation can make later low exposures trigger asthma. | Evening or night symptoms, worsening reliever use or surveillance changes may signal disease; ongoing exposure can leave lasting impairment. | Spray outside the assessed booth, ineffective extraction, premature entry or symptoms: stop exposure and get competent booth and health review. |
| 3 | High-level irritant gas, vapour or fume release | A substantial acute inhalation can inflame airways without the usual sensitisation delay; clinical assessment determines the disease pattern. | Immediate breathing symptoms may be serious; later persistent asthma is possible after a major exposure. | Evacuate or isolate by the emergency plan, obtain urgent medical help for severe breathing difficulty and do not restart before investigation. |
Common asthmagens and control focus
Table ID: occupational-asthma-common-asthmagens-and-control-focus
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Asthmagen or sector
Flour dust
- Typical exposure
Mixing, tipping, sieving, dusting and cleaning in bakeries.
- Control focus
Low-dust methods, enclosed transfer, LEV and no dry sweeping. HSE FLOUR
Row 2
- Asthmagen or sector
Isocyanates
- Typical exposure
Spray painting, 2K products, foam and coating work.
- Control focus
Substitution, spray booth, air-fed RPE, clearance time and surveillance. HSE MVR
Row 3
- Asthmagen or sector
Wood dust
- Typical exposure
Cutting, sanding, machining and cleaning.
- Control focus
LEV, on-tool extraction, housekeeping and surveillance. HSE ASTHMAGENS
Row 4
- Asthmagen or sector
Solder flux or rosin fume
- Typical exposure
Soldering and electronics work.
- Control focus
Tip extraction, LEV and process control. HSE ASTHMAGENS
Row 5
- Asthmagen or sector
Laboratory animal allergens
- Typical exposure
Animal handling, cage cleaning, bedding and laundry.
- Control focus
Containment, ventilation, work method and surveillance. HSE ASTHMAGENS
Row 6
- Asthmagen or sector
Enzymes and cleaning agents
- Typical exposure
Detergent, food, healthcare and cleaning work.
- Control focus
Substitution, dilution, closed systems and spray control. HSE ASTHMAGENS
Read the complete comparison table
| Row | Asthmagen or sector | Typical exposure | Control focus |
|---|---|---|---|
| 1 | Flour dust | Mixing, tipping, sieving, dusting and cleaning in bakeries. | Low-dust methods, enclosed transfer, LEV and no dry sweeping. HSE FLOUR |
| 2 | Isocyanates | Spray painting, 2K products, foam and coating work. | Substitution, spray booth, air-fed RPE, clearance time and surveillance. HSE MVR |
| 3 | Wood dust | Cutting, sanding, machining and cleaning. | LEV, on-tool extraction, housekeeping and surveillance. HSE ASTHMAGENS |
| 4 | Solder flux or rosin fume | Soldering and electronics work. | Tip extraction, LEV and process control. HSE ASTHMAGENS |
| 5 | Laboratory animal allergens | Animal handling, cage cleaning, bedding and laundry. | Containment, ventilation, work method and surveillance. HSE ASTHMAGENS |
| 6 | Enzymes and cleaning agents | Detergent, food, healthcare and cleaning work. | Substitution, dilution, closed systems and spray control. HSE ASTHMAGENS |
Asthma prevention across work sectors
Table ID: occupational-asthma-sector-transfer
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Sector task people
Manufacturing: vehicle-paint sprayers and nearby staff
- Route and harm
Isocyanate mist can escape spraying and cause sensitisation or worsen existing asthma.
- Strongest controls
Avoid isocyanate use where feasible; use a designed booth, verified clearance and competent air-fed RPE.
- Residual check
Check booth integrity, clearance and biological/health monitoring where indicated; stop for leakage or symptoms. HSE MVR
Row 2
- Sector task people
Construction: joiners, cleaners and others near timber cutting
- Route and harm
Some wood dust can reach airways and cause asthma; sweeping may re-suspend dust.
- Strongest controls
Use less dusty methods, on-tool extraction and segregation; avoid dry sweeping.
- Residual check
Inspect extraction and housekeeping; stop dusty cutting when controls fail. HSE ASTHMAGENS
Row 3
- Sector task people
Hospitality and food production: bakers and cleaners
- Route and harm
Flour and enzyme dust from tipping, dusting and clean-up can sensitise workers.
- Strongest controls
Use low-dust materials, closed or low-drop handling and effective extraction.
- Residual check
Observe flour clouds and work-linked symptoms; stop the dusty step and review surveillance. HSE FLOUR
Row 4
- Sector task people
Laboratories and animal facilities: handlers and laundry staff
- Route and harm
Animal proteins in aerosols or contaminated bedding can sensitise airways.
- Strongest controls
Use enclosure, ventilated handling and controlled bedding/laundry transfer.
- Residual check
Check access, ventilation and symptoms; hold work for containment failure. HSE ASTHMAGENS
Read the complete comparison table
| Row | Sector task people | Route and harm | Strongest controls | Residual check |
|---|---|---|---|---|
| 1 | Manufacturing: vehicle-paint sprayers and nearby staff | Isocyanate mist can escape spraying and cause sensitisation or worsen existing asthma. | Avoid isocyanate use where feasible; use a designed booth, verified clearance and competent air-fed RPE. | Check booth integrity, clearance and biological/health monitoring where indicated; stop for leakage or symptoms. HSE MVR |
| 2 | Construction: joiners, cleaners and others near timber cutting | Some wood dust can reach airways and cause asthma; sweeping may re-suspend dust. | Use less dusty methods, on-tool extraction and segregation; avoid dry sweeping. | Inspect extraction and housekeeping; stop dusty cutting when controls fail. HSE ASTHMAGENS |
| 3 | Hospitality and food production: bakers and cleaners | Flour and enzyme dust from tipping, dusting and clean-up can sensitise workers. | Use low-dust materials, closed or low-drop handling and effective extraction. | Observe flour clouds and work-linked symptoms; stop the dusty step and review surveillance. HSE FLOUR |
| 4 | Laboratories and animal facilities: handlers and laundry staff | Animal proteins in aerosols or contaminated bedding can sensitise airways. | Use enclosure, ventilated handling and controlled bedding/laundry transfer. | Check access, ventilation and symptoms; hold work for containment failure. HSE ASTHMAGENS |
Additional material hazard control hierarchy
Table ID: occupational-asthma-additional-hazard-hierarchy
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Column 1
Acute irritant gas or vapour release
- Column 2
Eliminate the mixing or transfer that produces the release if the process can change; otherwise test a lower-hazard product and verify it does not create another reaction. Enclose transfer, segregate the release area and provide designed capture or emergency ventilation.
- Column 3
COSHH owner checks product information, containment, extraction and detector/air results before start and after change; train for foreseeable release. Emergency RPE is only for a trained, authorised response, not routine entry. administrative supervision and checking sustain engineering and drills.
- Column 4
Stop mixing, withdraw and prevent entry for a leak, failed ventilation, alarm or symptoms; use the site emergency plan and competent responders, never an unplanned rescue.HSE ASTHMAGENS HSE PPE HIERARCHY HSENI COSHH
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Acute irritant gas or vapour release | Eliminate the mixing or transfer that produces the release if the process can change; otherwise test a lower-hazard product and verify it does not create another reaction. Enclose transfer, segregate the release area and provide designed capture or emergency ventilation. | COSHH owner checks product information, containment, extraction and detector/air results before start and after change; train for foreseeable release. Emergency RPE is only for a trained, authorised response, not routine entry. administrative supervision and checking sustain engineering and drills. | Stop mixing, withdraw and prevent entry for a leak, failed ventilation, alarm or symptoms; use the site emergency plan and competent responders, never an unplanned rescue.HSE ASTHMAGENS HSE PPE HIERARCHY HSENI COSHH |
Bakery occupational asthma scenario
Table ID: occupational-asthma-bakery-occupational-asthma-scenario
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Finding
Symptoms improve away from work
- Weak response
Dismissed as seasonal cough.
- Stronger response
Treat as possible work-related pattern and refer. HSE FLOUR
Row 2
- Finding
Open flour tipping
- Weak response
Accepted as traditional practice.
- Stronger response
Review enclosed or low-dust transfer. HSE FLOUR
Row 3
- Finding
Dry sweeping
- Weak response
Creates airborne flour dust.
- Stronger response
Use suitable vacuum and wet/controlled cleaning. HSE FLOUR
Row 4
- Finding
Disposable mask issued
- Weak response
PPE-only control.
- Stronger response
Apply hierarchy and select suitable RPE if needed. HSE FLOUR
Row 5
- Finding
Others may be exposed
- Weak response
Only one worker considered.
- Stronger response
Check exposure group and surveillance results. HSE FLOUR
Row 6
- Finding
No evidence trail
- Weak response
No control review recorded.
- Stronger response
Record COSHH review, actions and OH advice summary. HSE FLOUR
Read the complete comparison table
| Row | Finding | Weak response | Stronger response |
|---|---|---|---|
| 1 | Symptoms improve away from work | Dismissed as seasonal cough. | Treat as possible work-related pattern and refer. HSE FLOUR |
| 2 | Open flour tipping | Accepted as traditional practice. | Review enclosed or low-dust transfer. HSE FLOUR |
| 3 | Dry sweeping | Creates airborne flour dust. | Use suitable vacuum and wet/controlled cleaning. HSE FLOUR |
| 4 | Disposable mask issued | PPE-only control. | Apply hierarchy and select suitable RPE if needed. HSE FLOUR |
| 5 | Others may be exposed | Only one worker considered. | Check exposure group and surveillance results. HSE FLOUR |
| 6 | No evidence trail | No control review recorded. | Record COSHH review, actions and OH advice summary. HSE FLOUR |
Spray-painting control points
Table ID: occupational-asthma-spray-painting-control-points
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Task stage
Mixing
- Exposure concern
Vapour and skin contact during product preparation.
- Control standard
Ventilated mixing area, gloves, eye protection and training. HSE MVR
Row 2
- Task stage
Spraying
- Exposure concern
Aerosol inhalation and overspray.
- Control standard
Spray booth, air-fed RPE and trained sprayer. HSE MVR
Row 3
- Task stage
Curing and clearance
- Exposure concern
Residual aerosol or vapour remains in booth.
- Control standard
Observe booth clearance time before entry. HSE MVR
Row 4
- Task stage
Cleaning
- Exposure concern
Solvent and isocyanate residue exposure.
- Control standard
Controlled cleaning method and RPE/PPE review. HSE MVR
Row 5
- Task stage
Health surveillance
- Exposure concern
Early symptoms may indicate sensitisation.
- Control standard
OH programme and prompt symptom escalation. HSE MVR
Read the complete comparison table
| Row | Task stage | Exposure concern | Control standard |
|---|---|---|---|
| 1 | Mixing | Vapour and skin contact during product preparation. | Ventilated mixing area, gloves, eye protection and training. HSE MVR |
| 2 | Spraying | Aerosol inhalation and overspray. | Spray booth, air-fed RPE and trained sprayer. HSE MVR |
| 3 | Curing and clearance | Residual aerosol or vapour remains in booth. | Observe booth clearance time before entry. HSE MVR |
| 4 | Cleaning | Solvent and isocyanate residue exposure. | Controlled cleaning method and RPE/PPE review. HSE MVR |
| 5 | Health surveillance | Early symptoms may indicate sensitisation. | OH programme and prompt symptom escalation. HSE MVR |
Occupational asthma escalation guide
Table ID: occupational-asthma-occupational-asthma-escalation-guide
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Trigger
Wheeze, cough or chest tightness linked to work
- Immediate action
Stop uncontrolled exposure and signpost OH/medical advice.
- Follow up
COSHH and surveillance review. HSE ASTHMA
Row 2
- Trigger
Symptoms improve on rest days or holiday
- Immediate action
Treat as work-pattern signal.
- Follow up
Review asthmagen exposure. HSE ASTHMA
Row 3
- Trigger
LEV or booth defect
- Immediate action
Pause task if control depends on it.
- Follow up
Repair, test and verify. HSE ASTHMA
Row 4
- Trigger
Tight-fitting RPE without a suitable face-fit test, or any RPE that is incompatible or defective
- Immediate action
Do not rely on it for exposure control.
- Follow up
Select suitable RPE; face-fit test tight-fitting types. HSE ASTHMAHSE fit testing basics
Row 5
- Trigger
High-level irritant exposure
- Immediate action
Apply emergency and medical route.
- Follow up
Investigate and prevent repeat. HSE ASTHMA
Row 6
- Trigger
Health surveillance concern
- Immediate action
Use OH advice and protect confidentiality.
- Follow up
Check wider exposure group. HSE ASTHMA
Read the complete comparison table
| Row | Trigger | Immediate action | Follow up |
|---|---|---|---|
| 1 | Wheeze, cough or chest tightness linked to work | Stop uncontrolled exposure and signpost OH/medical advice. | COSHH and surveillance review. HSE ASTHMA |
| 2 | Symptoms improve on rest days or holiday | Treat as work-pattern signal. | Review asthmagen exposure. HSE ASTHMA |
| 3 | LEV or booth defect | Pause task if control depends on it. | Repair, test and verify. HSE ASTHMA |
| 4 | Tight-fitting RPE without a suitable face-fit test, or any RPE that is incompatible or defective | Do not rely on it for exposure control. | Select suitable RPE; face-fit test tight-fitting types. HSE ASTHMAHSE fit testing basics |
| 5 | High-level irritant exposure | Apply emergency and medical route. | Investigate and prevent repeat. HSE ASTHMA |
| 6 | Health surveillance concern | Use OH advice and protect confidentiality. | Check wider exposure group. HSE ASTHMA |
How do exposure controls and health surveillance connect?
Table ID: occupational-asthma-control-surveillance-plan-decisions
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html Scope: HSE G402 is Great Britain guidance; use the separate HSENI surveillance route for Northern Ireland. SHARE planning aid with competent OH interpretation, not diagnosis, a universal surveillance schedule or work-release approval.
Row 1
- Stage
Assess exposure
- Evidence
Manager and assessor identify tasks, substances and exposed groups.
- Action
Prevent or control exposure; agree whether surveillance is required with the provider.
Row 2
- Stage
Plan the scheme
- Evidence
OH specifies baseline assessment before exposure and appropriate ongoing checks.
- Action
If a baseline was missed, arrange it promptly; the six-week example in G402 is not a grace period.
Row 3
- Stage
Between appointments
- Evidence
Worker knows the reporting route; any appointed responsible person is trained and supported by OH.
- Action
Refer reported symptoms promptly rather than waiting for the next scheduled check.
Row 4
- Stage
Interpret and respond
- Evidence
OH gives individual work advice and interprets similarly exposed group results.
- Action
Manager reviews assessment and controls, and implements advised work restrictions or alternative duties.
Row 5
- Stage
Confirm action
- Evidence
Manager records control corrections and restricted work advice; clinical details stay with appropriate confidential systems.
- Action
Check the revised work arrangement and resolve outstanding advice with OH.
Read the complete comparison table
| Row | Stage | Evidence | Action |
|---|---|---|---|
| 1 | Assess exposure | Manager and assessor identify tasks, substances and exposed groups. | Prevent or control exposure; agree whether surveillance is required with the provider. |
| 2 | Plan the scheme | OH specifies baseline assessment before exposure and appropriate ongoing checks. | If a baseline was missed, arrange it promptly; the six-week example in G402 is not a grace period. |
| 3 | Between appointments | Worker knows the reporting route; any appointed responsible person is trained and supported by OH. | Refer reported symptoms promptly rather than waiting for the next scheduled check. |
| 4 | Interpret and respond | OH gives individual work advice and interprets similarly exposed group results. | Manager reviews assessment and controls, and implements advised work restrictions or alternative duties. |
| 5 | Confirm action | Manager records control corrections and restricted work advice; clinical details stay with appropriate confidential systems. | Check the revised work arrangement and resolve outstanding advice with OH. |
GB and Northern Ireland occupational asthma duties
Table ID: occupational-asthma-gb-ni-duties
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Jurisdiction
Great Britain
- Legal route
COSHH Regulations 2002 require assessment and prevention or adequate control of hazardous-substance exposure. Use HSE guidance for asthmagens, suitable health surveillance and the relevant EH40 workplace exposure limit.
- Evidence and boundary
Document the agent, task, source controls and findings. HSE guidance is not itself the law; meet a limit and still reduce sensitiser exposure as far as reasonably practicable. HSE ASTHMAGENS HSE EMPLOYERS
Row 2
- Jurisdiction
Northern Ireland
- Legal route
COSHH Regulations (Northern Ireland) 2003 provide the separate NI control and surveillance route. HSENI references EH40 but the NI instrument and regulator govern the decision.
- Evidence and boundary
Use HSENI guidance and check current NI provisions and applicable limits before legal reliance; do not cite GB COSHH as the NI regulation. HSENI COSHH HSENI LUNG
Row 3
- Jurisdiction
Great Britain reporting
- Legal route
RIDDOR 2013 can require reporting occupational asthma when a diagnosis and significant or regular work exposure to a known respiratory sensitiser meet its criteria.
- Evidence and boundary
Use HSE occupational-disease guidance; a symptom alone is not the reportable diagnosis. HSE RIDDOR
Row 4
- Jurisdiction
Northern Ireland reporting
- Legal route
RIDDOR (Northern Ireland) 1997 has its own disease-reporting route; HSENI includes occupational asthma with significant or regular exposure to a known respiratory sensitiser.
- Evidence and boundary
Follow the NI report route after written medical notification and the applicable conditions; do not use the GB 2013 instrument. HSENI RIDDOR
Row 5
- Jurisdiction
United Kingdom data protection
- Legal route
UK GDPR and the Data Protection Act 2018 govern workers’ health information.
- Evidence and boundary
Keep clinical detail restricted and share only work-control advice needed by managers. GOV.UK personal data an employer may keep
Read the complete comparison table
| Row | Jurisdiction | Legal route | Evidence and boundary |
|---|---|---|---|
| 1 | Great Britain | COSHH Regulations 2002 require assessment and prevention or adequate control of hazardous-substance exposure. Use HSE guidance for asthmagens, suitable health surveillance and the relevant EH40 workplace exposure limit. | Document the agent, task, source controls and findings. HSE guidance is not itself the law; meet a limit and still reduce sensitiser exposure as far as reasonably practicable. HSE ASTHMAGENS HSE EMPLOYERS |
| 2 | Northern Ireland | COSHH Regulations (Northern Ireland) 2003 provide the separate NI control and surveillance route. HSENI references EH40 but the NI instrument and regulator govern the decision. | Use HSENI guidance and check current NI provisions and applicable limits before legal reliance; do not cite GB COSHH as the NI regulation. HSENI COSHH HSENI LUNG |
| 3 | Great Britain reporting | RIDDOR 2013 can require reporting occupational asthma when a diagnosis and significant or regular work exposure to a known respiratory sensitiser meet its criteria. | Use HSE occupational-disease guidance; a symptom alone is not the reportable diagnosis. HSE RIDDOR |
| 4 | Northern Ireland reporting | RIDDOR (Northern Ireland) 1997 has its own disease-reporting route; HSENI includes occupational asthma with significant or regular exposure to a known respiratory sensitiser. | Follow the NI report route after written medical notification and the applicable conditions; do not use the GB 2013 instrument. HSENI RIDDOR |
| 5 | United Kingdom data protection | UK GDPR and the Data Protection Act 2018 govern workers’ health information. | Keep clinical detail restricted and share only work-control advice needed by managers. GOV.UK personal data an employer may keep |
Role learning and competence checks
Table ID: occupational-asthma-role-competence
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Role
Nearby staff and new starters
- Learning and test
Recognise dust/mist releases, early symptoms and the reporting route. Awareness does not authorise hazardous tasks.
- Assessor and evidence
Supervisor checks a scenario; briefing and response record remain.
- Reassessment trigger
New agent, changed site or missed signal.
Row 2
- Role
Bakers, sprayers and other operators
- Learning and test
Identify the actual asthmagen, use the assessed enclosure/LEV/RPE and stop for defect or symptom.
- Assessor and evidence
Competent supervisor observes actual task and checks product and control knowledge; authorisation record remains.
- Reassessment trigger
Product, booth, equipment or method changes.
Row 3
- Role
Maintenance and contractors
- Learning and test
Isolate equipment, avoid secondary release during cleaning or repair and hand back with control checks.
- Assessor and evidence
Competent maintenance lead checks method and practical hand-back; work record remains.
- Reassessment trigger
Defect, modification or contractor change.
Row 4
- Role
Supervisors and managers
- Learning and test
Challenge a weak COSHH assessment, hold uncontrolled work, respond privately to symptoms and commission competent advice.
- Assessor and evidence
Safety/technical lead assesses a scenario and control decision; action and restart record remain.
- Reassessment trigger
Symptom, failed control, audit or changed process.
Row 5
- Role
Hygienists, OH and auditors
- Learning and test
Design exposure or surveillance checks within competence and trace source-control decisions without sharing unnecessary health details.
- Assessor and evidence
Professionally competent lead reviews sample plan, referral or audit; restricted specialist record remains.
- Reassessment trigger
New evidence, abnormal finding or unresolved trend.
Read the complete comparison table
| Row | Role | Learning and test | Assessor and evidence | Reassessment trigger |
|---|---|---|---|---|
| 1 | Nearby staff and new starters | Recognise dust/mist releases, early symptoms and the reporting route. Awareness does not authorise hazardous tasks. | Supervisor checks a scenario; briefing and response record remain. | New agent, changed site or missed signal. |
| 2 | Bakers, sprayers and other operators | Identify the actual asthmagen, use the assessed enclosure/LEV/RPE and stop for defect or symptom. | Competent supervisor observes actual task and checks product and control knowledge; authorisation record remains. | Product, booth, equipment or method changes. |
| 3 | Maintenance and contractors | Isolate equipment, avoid secondary release during cleaning or repair and hand back with control checks. | Competent maintenance lead checks method and practical hand-back; work record remains. | Defect, modification or contractor change. |
| 4 | Supervisors and managers | Challenge a weak COSHH assessment, hold uncontrolled work, respond privately to symptoms and commission competent advice. | Safety/technical lead assesses a scenario and control decision; action and restart record remain. | Symptom, failed control, audit or changed process. |
| 5 | Hygienists, OH and auditors | Design exposure or surveillance checks within competence and trace source-control decisions without sharing unnecessary health details. | Professionally competent lead reviews sample plan, referral or audit; restricted specialist record remains. | New evidence, abnormal finding or unresolved trend. |
BuildOut Ltd worked example
Table ID: occupational-asthma-buildout-ltd-worked-example
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Management element
Identify
- How the business would manage it
Asthmagens are named in COSHH assessments.
- Evidence to review
Asthmagen register. HSE EMPLOYERS
Row 2
- Management element
Control
- How the business would manage it
Substitution, LEV, cleaning and RPE standards are specified.
- Evidence to review
Task control standard. HSE EMPLOYERS
Row 3
- Management element
Health
- How the business would manage it
Surveillance and symptom routes are clear.
- Evidence to review
OH programme. HSE EMPLOYERS
Row 4
- Management element
Assure
- How the business would manage it
LEV, RPE, training and symptoms are reviewed.
- Evidence to review
Assurance dashboard. HSE EMPLOYERS
Read the complete comparison table
| Row | Management element | How the business would manage it | Evidence to review |
|---|---|---|---|
| 1 | Identify | Asthmagens are named in COSHH assessments. | Asthmagen register. HSE EMPLOYERS |
| 2 | Control | Substitution, LEV, cleaning and RPE standards are specified. | Task control standard. HSE EMPLOYERS |
| 3 | Health | Surveillance and symptom routes are clear. | OH programme. HSE EMPLOYERS |
| 4 | Assure | LEV, RPE, training and symptoms are reviewed. | Assurance dashboard. HSE EMPLOYERS |
Source comparison
Table ID: occupational-asthma-activity-control-hierarchy
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Column 1
Eliminate
- Column 2
Use a suitable supplied dough or a contained supply arrangement that removes local open bag emptying where feasible.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Task owner verifies that the proposed change removes the named hazardous step, including foreseeable cleaning, maintenance and work transferred elsewhere.
- Column 4
If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
Row 2
- Column 1
Reduce, including substitution
- Column 2
Validate a suitable low-dust flour or improver form while checking allergenic, skin, quality and process hazards.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Competent task/process owner validates suitability, compatibility and new hazards against the actual operating requirements before the alternative is adopted.
- Column 4
Reject an alternative if its performance is unproved or its new hazards are unresolved.
Row 3
- Column 1
Isolate
- Column 2
Enclose or segregate charging and keep other workers away from the release; prevent dust spreading into clean work.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Supervisor checks the actual boundary, affected people and connected work; verify separation or isolation before allowing access.
- Column 4
Hold or stop for failed extraction, damaged cover, uncontrolled flour cloud or changed material not assessed.
Row 4
- Column 1
Control: physical safeguards
- Column 2
Provide effective capture and suitable mixer covers or contained charging; use dust-controlled cleaning instead of dry sweeping.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Competent equipment/process owner checks flour/improver identity, charging height, capture, mixer cover and cleaning effectiveness.
- Column 4
Hold or stop for failed extraction, damaged cover, uncontrolled flour cloud or changed material not assessed.
Row 5
- Column 1
Control: work method and response
- Column 2
Use a low-release charging method and realistic quantities; include maintenance, exposure review and required health surveillance in the plan.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Supervisor confirms the work limits, competent cover, communication and stop/restart authority with the people doing this activity.
- Column 4
Hold work when the agreed limits, competent cover or effective communication cannot be maintained.
Row 6
- Column 1
PPE
- Column 2
Select adequate suitable RPE for remaining exposure and required fit evidence. A mask does not correct failed extraction or an open uncontrolled dust cloud.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Assessor confirms whether personal protection is needed and checks suitability, condition, compatibility and any required fit evidence.
- Column 4
Do not use unsuitable protection or rely on PPE to continue after an essential source control fails.
Row 7
- Column 1
Discipline
- Column 2
Check capture and covers before use and after recipe or throughput changes; investigate respiratory reports and verify corrective action.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Release only after bakery owner accepts a validated method and effective source controls. Retain verification and unresolved restrictions at handover.
- Column 4
Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Eliminate | Use a suitable supplied dough or a contained supply arrangement that removes local open bag emptying where feasible.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Task owner verifies that the proposed change removes the named hazardous step, including foreseeable cleaning, maintenance and work transferred elsewhere. | If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls. |
| 2 | Reduce, including substitution | Validate a suitable low-dust flour or improver form while checking allergenic, skin, quality and process hazards.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Competent task/process owner validates suitability, compatibility and new hazards against the actual operating requirements before the alternative is adopted. | Reject an alternative if its performance is unproved or its new hazards are unresolved. |
| 3 | Isolate | Enclose or segregate charging and keep other workers away from the release; prevent dust spreading into clean work.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Supervisor checks the actual boundary, affected people and connected work; verify separation or isolation before allowing access. | Hold or stop for failed extraction, damaged cover, uncontrolled flour cloud or changed material not assessed. |
| 4 | Control: physical safeguards | Provide effective capture and suitable mixer covers or contained charging; use dust-controlled cleaning instead of dry sweeping.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Competent equipment/process owner checks flour/improver identity, charging height, capture, mixer cover and cleaning effectiveness. | Hold or stop for failed extraction, damaged cover, uncontrolled flour cloud or changed material not assessed. |
| 5 | Control: work method and response | Use a low-release charging method and realistic quantities; include maintenance, exposure review and required health surveillance in the plan.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Supervisor confirms the work limits, competent cover, communication and stop/restart authority with the people doing this activity. | Hold work when the agreed limits, competent cover or effective communication cannot be maintained. |
| 6 | PPE | Select adequate suitable RPE for remaining exposure and required fit evidence. A mask does not correct failed extraction or an open uncontrolled dust cloud.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Assessor confirms whether personal protection is needed and checks suitability, condition, compatibility and any required fit evidence. | Do not use unsuitable protection or rely on PPE to continue after an essential source control fails. |
| 7 | Discipline | Check capture and covers before use and after recipe or throughput changes; investigate respiratory reports and verify corrective action.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Release only after bakery owner accepts a validated method and effective source controls. Retain verification and unresolved restrictions at handover. | Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner. |
Source tables and records 2
Source comparison
Table ID: occupational-asthma-activity-control-hierarchy-eseap
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Column 1
Elimination
- Column 2
Use a suitable supplied dough or a contained supply arrangement that removes local open bag emptying where feasible.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Task owner verifies that the proposed change removes the named hazardous step, including foreseeable cleaning, maintenance and work transferred elsewhere.
- Column 4
If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
Row 2
- Column 1
Substitution
- Column 2
Validate a suitable low-dust flour or improver form while checking allergenic, skin, quality and process hazards.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Competent task/process owner validates suitability, compatibility and new hazards against the actual operating requirements before the alternative is adopted.
- Column 4
Reject an alternative if its performance is unproved or its new hazards are unresolved.
Row 3
- Column 1
Engineering controls
- Column 2
Enclose or segregate charging and keep other workers away from the release; prevent dust spreading into clean work.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Supervisor checks the actual boundary, affected people and connected work; verify separation or isolation before allowing access.
- Column 4
Hold or stop for failed extraction, damaged cover, uncontrolled flour cloud or changed material not assessed.
Row 4
- Column 1
Engineering controls
- Column 2
Provide effective capture and suitable mixer covers or contained charging; use dust-controlled cleaning instead of dry sweeping.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Competent equipment/process owner checks flour/improver identity, charging height, capture, mixer cover and cleaning effectiveness.
- Column 4
Hold or stop for failed extraction, damaged cover, uncontrolled flour cloud or changed material not assessed.
Row 5
- Column 1
Administrative controls
- Column 2
Use a low-release charging method and realistic quantities; include maintenance, exposure review and required health surveillance in the plan.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Supervisor confirms the work limits, competent cover, communication and stop/restart authority with the people doing this activity.
- Column 4
Hold work when the agreed limits, competent cover or effective communication cannot be maintained.
Row 6
- Column 1
PPE
- Column 2
Select adequate suitable RPE for remaining exposure and required fit evidence. A mask does not correct failed extraction or an open uncontrolled dust cloud.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Assessor confirms whether personal protection is needed and checks suitability, condition, compatibility and any required fit evidence.
- Column 4
Do not use unsuitable protection or rely on PPE to continue after an essential source control fails.
Row 7
- Column 1
Administrative controls
- Column 2
Check capture and covers before use and after recipe or throughput changes; investigate respiratory reports and verify corrective action.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances
- Column 3
Release only after bakery owner accepts a validated method and effective source controls. Retain verification and unresolved restrictions at handover.
- Column 4
Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Elimination | Use a suitable supplied dough or a contained supply arrangement that removes local open bag emptying where feasible.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Task owner verifies that the proposed change removes the named hazardous step, including foreseeable cleaning, maintenance and work transferred elsewhere. | If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls. |
| 2 | Substitution | Validate a suitable low-dust flour or improver form while checking allergenic, skin, quality and process hazards.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Competent task/process owner validates suitability, compatibility and new hazards against the actual operating requirements before the alternative is adopted. | Reject an alternative if its performance is unproved or its new hazards are unresolved. |
| 3 | Engineering controls | Enclose or segregate charging and keep other workers away from the release; prevent dust spreading into clean work.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Supervisor checks the actual boundary, affected people and connected work; verify separation or isolation before allowing access. | Hold or stop for failed extraction, damaged cover, uncontrolled flour cloud or changed material not assessed. |
| 4 | Engineering controls | Provide effective capture and suitable mixer covers or contained charging; use dust-controlled cleaning instead of dry sweeping.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Competent equipment/process owner checks flour/improver identity, charging height, capture, mixer cover and cleaning effectiveness. | Hold or stop for failed extraction, damaged cover, uncontrolled flour cloud or changed material not assessed. |
| 5 | Administrative controls | Use a low-release charging method and realistic quantities; include maintenance, exposure review and required health surveillance in the plan.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Supervisor confirms the work limits, competent cover, communication and stop/restart authority with the people doing this activity. | Hold work when the agreed limits, competent cover or effective communication cannot be maintained. |
| 6 | PPE | Select adequate suitable RPE for remaining exposure and required fit evidence. A mask does not correct failed extraction or an open uncontrolled dust cloud.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Assessor confirms whether personal protection is needed and checks suitability, condition, compatibility and any required fit evidence. | Do not use unsuitable protection or rely on PPE to continue after an essential source control fails. |
| 7 | Administrative controls | Check capture and covers before use and after recipe or throughput changes; investigate respiratory reports and verify corrective action.Basis: HSE occupational asthma in food manufacture · HSE control of exposure to hazardous substances | Release only after bakery owner accepts a validated method and effective source controls. Retain verification and unresolved restrictions at handover. | Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner. |
Related SHARE pages
Table ID: occupational-asthma-related-share-pages
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Related page
Isocyanate Asthma
- Why it helps
Spray painting and isocyanate-specific asthma controls.
Row 2
- Related page
Wood Dust
- Why it helps
Wood dust health risks and controls.
Row 3
- Related page
Laboratory Animal Allergy
- Why it helps
Animal allergen sensitisation and surveillance.
Row 4
- Related page
LEV Local Exhaust Ventilation
- Why it helps
LEV principles, TExT and assurance.
Row 5
- Related page
COSHH Control Measures and Health Surveillance
- Why it helps
Hazardous substance control hierarchy and surveillance.
Read the complete comparison table
| Row | Related page | Why it helps |
|---|---|---|
| 1 | Isocyanate Asthma | Spray painting and isocyanate-specific asthma controls. |
| 2 | Wood Dust | Wood dust health risks and controls. |
| 3 | Laboratory Animal Allergy | Animal allergen sensitisation and surveillance. |
| 4 | LEV Local Exhaust Ventilation | LEV principles, TExT and assurance. |
| 5 | COSHH Control Measures and Health Surveillance | Hazardous substance control hierarchy and surveillance. |
Official links and supported decisions
Table ID: occupational-asthma-official-source-decisions
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Column 1
HSE
- Column 2
HSE asthma overview
- Column 3
Great Britain
- Column 4
Mechanism, symptoms, work-related distinction and delayed symptoms.
Row 2
- Column 1
HSE
- Column 2
HSE substances that can cause occupational asthma
- Column 3
Great Britain
- Column 4
Examples of recognised asthmagens and work uses.
Row 3
- Column 1
HSE
- Column 2
HSE advice for employers · Page date not stated; RIDDOR wording needs current 2013 route
- Column 3
Great Britain
- Column 4
COSHH source controls and suitable surveillance. This older page still uses previous reporting wording; use the current RIDDOR source below.
Row 4
- Column 1
HSE
- Column 2
HSE flour dust and risks to bakers
- Column 3
Great Britain
- Column 4
Flour asthma, 8-hour and 15-minute GB WELs and reduction well below them.
Row 5
- Column 1
HSE
- Column 2
HSE 2-pack isocyanate paints
- Column 3
Great Britain
- Column 4
Spray-booth, clearance, air-fed RPE, monitoring and surveillance decisions.
Row 6
- Column 1
HSE
- Column 2
HSE HSG276 isocyanate paint spraying · 2014
- Column 3
Great Britain
- Column 4
Safely managing booths and spray rooms.
Row 7
- Column 1
HSE
- Column 2
HSE INDG388 safety in isocyanate paint spraying · 2014 revision 2
- Column 3
Great Britain
- Column 4
Worker-facing spray-paint controls.
Row 8
- Column 1
HSE
- Column 2
HSE isocyanate biological monitoring
- Column 3
Great Britain
- Column 4
Use and timing of biological monitoring for spray painters.
Row 9
- Column 1
HSE
- Column 2
HSE G402 health surveillance for occupational asthma · 2022
- Column 3
Great Britain
- Column 4
When and how to plan surveillance for occupational asthma.
Row 10
- Column 1
HSE
- Column 2
HSE reportable occupational diseases
- Column 3
Great Britain
- Column 4
GB occupational-asthma reporting condition.
Row 11
- Column 1
HSENI
- Column 2
HSENI occupational lung disease
- Column 3
Northern Ireland
- Column 4
NI COSHH 2003 route, occupational asthma and controls.
Row 12
- Column 1
HSENI
- Column 2
HSENI health and medical surveillance
- Column 3
Northern Ireland
- Column 4
NI surveillance criteria for asthmagens.
Row 13
- Column 1
HSENI
- Column 2
HSENI reporting occupational diseases · Page date not stated; health and social care example
- Column 3
Northern Ireland
- Column 4
NI RIDDOR 1997 and occupational asthma disease criteria; sector example supports the legal route.
Row 14
- Column 1
nidirect
- Column 2
nidirect asthma
- Column 3
Northern Ireland health information; workplace control separately checked
- Column 4
Northern Ireland asthma symptom information; workplace causation and exposure control require a separate occupational assessment.
Row 15
- Column 1
HSE
- Column 2
HSE hierarchy of controls
- Column 3
Great Britain workplace guidance
- Column 4
For flour, isocyanate and other asthmagen exposures, consider removing or changing the task first, then engineered separation before relying on procedures or PPE.
Row 16
- Column 1
HSE
- Column 2
HSE HSG65 managing for health and safety · Third edition 2013
- Column 3
Great Britain
- Column 4
Plan–Do–Check–Act management guidance.
Row 17
- Column 1
HSE
- Column 2
HSE Plan, Do, Check, Act
- Column 3
Great Britain management guidance
- Column 4
Use the HSE management cycle to assign asthmagen controls and surveillance, check that controls work and revise them after a failure or change.
Row 18
- Column 1
GOV.UK
- Column 2
GOV.UK personal data an employer may keep
- Column 3
UK general information; detailed lawful-basis analysis held
- Column 4
Keep worker health records for asthmagen controls and surveillance limited to necessary work information; use the government employer-data route for privacy and access questions.
Row 19
- Column 1
HSENI
- Column 2
HSENI COSHH · Page date not stated
- Column 3
Northern Ireland
- Column 4
Separate NI COSHH 2003 route for harmful substances.
Row 20
- Column 1
HSENI
- Column 2
HSENI EH40/2005 workplace exposure limits · Published 17 January 2020
- Column 3
Northern Ireland
- Column 4
EH40 approval for NI COSHH 2003; check current amendments.
Row 21
- Column 1
HSE
- Column 2
HSE fit testing basics
- Column 3
Great Britain
- Column 4
Fit testing of tight-fitting respiratory protective equipment for the individual wearer.
Row 22
- Column 1
HSE
- Column 2
HSE health-surveillance record keeping
- Column 3
Great Britain
- Column 4
Employer health records and confidential medical records are different; hazard-specific retention and provider transfer.
Row 23
- Column 1
www.legislation.gov.uk
- Column 2
COSHH regulation 11
- Column 3
Scope stated beside the link
- Column 4
Additional primary route for COSHH regulation 11; use the page-specific scope and national/clinical boundaries stated beside the link.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | HSE | HSE asthma overview | Great Britain | Mechanism, symptoms, work-related distinction and delayed symptoms. |
| 2 | HSE | HSE substances that can cause occupational asthma | Great Britain | Examples of recognised asthmagens and work uses. |
| 3 | HSE | HSE advice for employers · Page date not stated; RIDDOR wording needs current 2013 route | Great Britain | COSHH source controls and suitable surveillance. This older page still uses previous reporting wording; use the current RIDDOR source below. |
| 4 | HSE | HSE flour dust and risks to bakers | Great Britain | Flour asthma, 8-hour and 15-minute GB WELs and reduction well below them. |
| 5 | HSE | HSE 2-pack isocyanate paints | Great Britain | Spray-booth, clearance, air-fed RPE, monitoring and surveillance decisions. |
| 6 | HSE | HSE HSG276 isocyanate paint spraying · 2014 | Great Britain | Safely managing booths and spray rooms. |
| 7 | HSE | HSE INDG388 safety in isocyanate paint spraying · 2014 revision 2 | Great Britain | Worker-facing spray-paint controls. |
| 8 | HSE | HSE isocyanate biological monitoring | Great Britain | Use and timing of biological monitoring for spray painters. |
| 9 | HSE | HSE G402 health surveillance for occupational asthma · 2022 | Great Britain | When and how to plan surveillance for occupational asthma. |
| 10 | HSE | HSE reportable occupational diseases | Great Britain | GB occupational-asthma reporting condition. |
| 11 | HSENI | HSENI occupational lung disease | Northern Ireland | NI COSHH 2003 route, occupational asthma and controls. |
| 12 | HSENI | HSENI health and medical surveillance | Northern Ireland | NI surveillance criteria for asthmagens. |
| 13 | HSENI | HSENI reporting occupational diseases · Page date not stated; health and social care example | Northern Ireland | NI RIDDOR 1997 and occupational asthma disease criteria; sector example supports the legal route. |
| 14 | nidirect | nidirect asthma | Northern Ireland health information; workplace control separately checked | Northern Ireland asthma symptom information; workplace causation and exposure control require a separate occupational assessment. |
| 15 | HSE | HSE hierarchy of controls | Great Britain workplace guidance | For flour, isocyanate and other asthmagen exposures, consider removing or changing the task first, then engineered separation before relying on procedures or PPE. |
| 16 | HSE | HSE HSG65 managing for health and safety · Third edition 2013 | Great Britain | Plan–Do–Check–Act management guidance. |
| 17 | HSE | HSE Plan, Do, Check, Act | Great Britain management guidance | Use the HSE management cycle to assign asthmagen controls and surveillance, check that controls work and revise them after a failure or change. |
| 18 | GOV.UK | GOV.UK personal data an employer may keep | UK general information; detailed lawful-basis analysis held | Keep worker health records for asthmagen controls and surveillance limited to necessary work information; use the government employer-data route for privacy and access questions. |
| 19 | HSENI | HSENI COSHH · Page date not stated | Northern Ireland | Separate NI COSHH 2003 route for harmful substances. |
| 20 | HSENI | HSENI EH40/2005 workplace exposure limits · Published 17 January 2020 | Northern Ireland | EH40 approval for NI COSHH 2003; check current amendments. |
| 21 | HSE | HSE fit testing basics | Great Britain | Fit testing of tight-fitting respiratory protective equipment for the individual wearer. |
| 22 | HSE | HSE health-surveillance record keeping | Great Britain | Employer health records and confidential medical records are different; hazard-specific retention and provider transfer. |
| 23 | www.legislation.gov.uk | COSHH regulation 11 | Scope stated beside the link | Additional primary route for COSHH regulation 11; use the page-specific scope and national/clinical boundaries stated beside the link. |
Acronyms and meanings
Table ID: occupational-asthma-acronyms-and-meanings
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Acronym
COSHH
- Meaning
Control of Substances Hazardous to Health
- Plain english use
Hazardous-substance control: GB 2002 regulations and separate NI 2003 regulations.
Row 2
- Acronym
EH40
- Meaning
Workplace Exposure Limits guidance
- Plain english use
HSE publication listing many workplace exposure limits used with COSHH assessments.
Row 3
- Acronym
GP
- Meaning
General Practitioner
- Plain english use
A doctor in primary care who can assess, advise, treat or refer.
Row 4
- Acronym
HSE
- Meaning
Health and Safety Executive
- Plain english use
Great Britain workplace health and safety regulator.
Row 5
- Acronym
HSWA
- Meaning
Health and Safety at Work etc. Act 1974
- Plain english use
The core general work-safety statute for Great Britain; Northern Ireland uses the 1978 Order.
Row 6
- Acronym
LEV
- Meaning
Local Exhaust Ventilation
- Plain english use
Engineered extraction that captures contaminants close to source.
Row 7
- Acronym
MHSWR
- Meaning
Management of Health and Safety at Work Regulations 1999
- Plain english use
GB risk-assessment regulations; Northern Ireland has separate 2000 management regulations.
Row 8
- Acronym
OH
- Meaning
Occupational Health
- Plain english use
Competent health advice focused on work impact, fitness, restrictions, adjustments and prevention.
Row 9
- Acronym
PPE
- Meaning
Personal Protective Equipment
- Plain english use
Equipment worn as a last line of protection.
Row 10
- Acronym
RIDDOR
- Meaning
Reporting of Injuries, Diseases and Dangerous Occurrences Regulations
- Plain english use
Disease reporting: 2013 regulations in Great Britain; 1997 regulations in Northern Ireland.
Row 11
- Acronym
RPE
- Meaning
Respiratory Protective Equipment
- Plain english use
Respiratory protection used where inhalation exposure remains after higher-level controls.
Row 12
- Acronym
WEL
- Meaning
Workplace Exposure Limit
- Plain english use
A substance-specific exposure limit; apply the GB EH40 or NI COSHH route as appropriate and still control sensitisers at source.
Row 13
- Acronym
GB
- Meaning
Great Britain
- Plain english use
England, Scotland and Wales; HSE is the principal workplace regulator.
Row 14
- Acronym
NI
- Meaning
Northern Ireland
- Plain english use
Separate health-and-safety instruments and the HSENI regulator route.
Read the complete comparison table
| Row | Acronym | Meaning | Plain english use |
|---|---|---|---|
| 1 | COSHH | Control of Substances Hazardous to Health | Hazardous-substance control: GB 2002 regulations and separate NI 2003 regulations. |
| 2 | EH40 | Workplace Exposure Limits guidance | HSE publication listing many workplace exposure limits used with COSHH assessments. |
| 3 | GP | General Practitioner | A doctor in primary care who can assess, advise, treat or refer. |
| 4 | HSE | Health and Safety Executive | Great Britain workplace health and safety regulator. |
| 5 | HSWA | Health and Safety at Work etc. Act 1974 | The core general work-safety statute for Great Britain; Northern Ireland uses the 1978 Order. |
| 6 | LEV | Local Exhaust Ventilation | Engineered extraction that captures contaminants close to source. |
| 7 | MHSWR | Management of Health and Safety at Work Regulations 1999 | GB risk-assessment regulations; Northern Ireland has separate 2000 management regulations. |
| 8 | OH | Occupational Health | Competent health advice focused on work impact, fitness, restrictions, adjustments and prevention. |
| 9 | PPE | Personal Protective Equipment | Equipment worn as a last line of protection. |
| 10 | RIDDOR | Reporting of Injuries, Diseases and Dangerous Occurrences Regulations | Disease reporting: 2013 regulations in Great Britain; 1997 regulations in Northern Ireland. |
| 11 | RPE | Respiratory Protective Equipment | Respiratory protection used where inhalation exposure remains after higher-level controls. |
| 12 | WEL | Workplace Exposure Limit | A substance-specific exposure limit; apply the GB EH40 or NI COSHH route as appropriate and still control sensitisers at source. |
| 13 | GB | Great Britain | England, Scotland and Wales; HSE is the principal workplace regulator. |
| 14 | NI | Northern Ireland | Separate health-and-safety instruments and the HSENI regulator route. |
Potential SHARE downloads to add later
Table ID: occupational-asthma-potential-share-downloads-to-add-later
Source: https://www.sharehub.ltd/knowledge-hub/occupational-asthma.html
Row 1
- Document
Asthmagen COSHH checklist
- Purpose
Substance, task, exposure route, control and surveillance prompts.
- Typical owner
HSE adviser
Row 2
- Document
Occupational asthma symptom card
- Purpose
Work-pattern symptoms and reporting triggers.
- Typical owner
Worker
Row 3
- Document
Respiratory surveillance action prompt
- Purpose
How health findings should trigger control review.
- Typical owner
Manager
Read the complete comparison table
| Row | Document | Purpose | Typical owner |
|---|---|---|---|
| 1 | Asthmagen COSHH checklist | Substance, task, exposure route, control and surveillance prompts. | HSE adviser |
| 2 | Occupational asthma symptom card | Work-pattern symptoms and reporting triggers. | Worker |
| 3 | Respiratory surveillance action prompt | How health findings should trigger control review. | Manager |
Task-specific HSE control priorities
Table ID: isocyanate-asthma-control-control-examples
Source: https://www.sharehub.ltd/knowledge-hub/isocyanate-asthma.html
Row 1
- Control priority
Eliminate
- Practical control
Avoid isocyanate product or spraying where possible.
- Example
Use non-isocyanate alternative or prefinished component.
Row 2
- Control priority
Substitute
- Practical control
Replace the product or process with an assessed less hazardous alternative where feasible. Quantity reduction is minimisation, and improved spray equipment is engineering/process control; neither is automatically substitution.
- Example
A genuinely lower-hazard replacement needs assessment. HVLP can improve transfer efficiency but residual isocyanate mist remains and required spray protection still applies.
Row 3
- Control priority
Engineering
- Practical control
Enclose or separate the task and capture aerosol or fume at source.
- Example
Verify booth or local exhaust ventilation, access control and bystander separation.
Row 4
- Control priority
Administrative
- Practical control
Brief, supervise and stop unsafe practices.
- Example
No visor lifting, no uncontrolled cleaning.
Row 5
- Control priority
Personal protection
- Practical control
Use suitable gloves, coveralls, eye protection and BA.
- Example
RPE programme and skin protection.
Read the complete comparison table
| Row | Control priority | Practical control | Example |
|---|---|---|---|
| 1 | Eliminate | Avoid isocyanate product or spraying where possible. | Use non-isocyanate alternative or prefinished component. |
| 2 | Substitute | Replace the product or process with an assessed less hazardous alternative where feasible. Quantity reduction is minimisation, and improved spray equipment is engineering/process control; neither is automatically substitution. | A genuinely lower-hazard replacement needs assessment. HVLP can improve transfer efficiency but residual isocyanate mist remains and required spray protection still applies. |
| 3 | Engineering | Enclose or separate the task and capture aerosol or fume at source. | Verify booth or local exhaust ventilation, access control and bystander separation. |
| 4 | Administrative | Brief, supervise and stop unsafe practices. | No visor lifting, no uncontrolled cleaning. |
| 5 | Personal protection | Use suitable gloves, coveralls, eye protection and BA. | RPE programme and skin protection. |
RPE and booth assurance
Table ID: isocyanate-asthma-rpe-and-booth-assurance
Source: https://www.sharehub.ltd/knowledge-hub/isocyanate-asthma.html
Row 1
- Control
Air-fed BA
- Good practice
Suitable air-fed BA, APF at least 20, low-flow indicator; half-mask only with continuing biological-monitoring evidence.
- Evidence
Selection record, manufacturer minimum-flow and air-supply checks, low-flow test and monitoring review.
Row 2
- Control
Breathing air quality
- Good practice
Clean air at required pressure/flow.
- Evidence
Air quality test and compressor maintenance.
Row 3
- Control
Booth clearance time
- Good practice
Measured and communicated.
- Evidence
Clearance test and sign.
Row 4
- Control
Extraction
- Good practice
Maintained and not leaking mist.
- Evidence
LEV/booth maintenance record.
Row 5
- Control
Visor discipline
- Good practice
BA kept on until outside/clear.
- Evidence
Observation and training.
Row 6
- Control
Fit testing
- Good practice
For tight-fitting RPE where used.
- Evidence
Fit-test record.
Read the complete comparison table
| Row | Control | Good practice | Evidence |
|---|---|---|---|
| 1 | Air-fed BA | Suitable air-fed BA, APF at least 20, low-flow indicator; half-mask only with continuing biological-monitoring evidence. | Selection record, manufacturer minimum-flow and air-supply checks, low-flow test and monitoring review. |
| 2 | Breathing air quality | Clean air at required pressure/flow. | Air quality test and compressor maintenance. |
| 3 | Booth clearance time | Measured and communicated. | Clearance test and sign. |
| 4 | Extraction | Maintained and not leaking mist. | LEV/booth maintenance record. |
| 5 | Visor discipline | BA kept on until outside/clear. | Observation and training. |
| 6 | Fit testing | For tight-fitting RPE where used. | Fit-test record. |
Biological monitoring programme
Table ID: isocyanate-asthma-biological-monitoring-programme
Source: https://www.sharehub.ltd/knowledge-hub/isocyanate-asthma.html
Row 1
- Element
Sampling timing
- Why it matters
Select analysis for the isocyanates actually used and sample representative work at the end of potential exposure, within about an hour, following laboratory instructions.
- Evidence
Sampling instruction and chain of custody.
Row 2
- Element
Worker briefing
- Why it matters
Workers understand purpose and privacy.
- Evidence
Consent and information record.
Row 3
- Element
Result interpretation
- Why it matters
Competent review turns result into action.
- Evidence
OH/hygiene report.
Row 4
- Element
Control review
- Why it matters
Unexpected result triggers booth/RPE/work-practice review.
- Evidence
Action tracker.
Row 5
- Element
Trend review
- Why it matters
Shows whether programme is improving control.
- Evidence
Monitoring dashboard.
Read the complete comparison table
| Row | Element | Why it matters | Evidence |
|---|---|---|---|
| 1 | Sampling timing | Select analysis for the isocyanates actually used and sample representative work at the end of potential exposure, within about an hour, following laboratory instructions. | Sampling instruction and chain of custody. |
| 2 | Worker briefing | Workers understand purpose and privacy. | Consent and information record. |
| 3 | Result interpretation | Competent review turns result into action. | OH/hygiene report. |
| 4 | Control review | Unexpected result triggers booth/RPE/work-practice review. | Action tracker. |
| 5 | Trend review | Shows whether programme is improving control. | Monitoring dashboard. |
Health surveillance prompts
Table ID: isocyanate-asthma-health-surveillance-prompts
Source: https://www.sharehub.ltd/knowledge-hub/isocyanate-asthma.html
Row 1
- Surveillance element
Baseline questionnaire
- Purpose
Records starting respiratory/skin status.
- Evidence
OH health record.
Row 2
- Surveillance element
Early follow-up
- Purpose
Detects early sensitisation pattern.
- Evidence
6-week/6-month style review where applicable.
Row 3
- Surveillance element
Annual review
- Purpose
Ongoing detection and trend.
- Evidence
Lung function and questionnaire record.
Row 4
- Surveillance element
Skin checks
- Purpose
Identify dermatitis or sensitisation.
- Evidence
Skin surveillance record.
Row 5
- Surveillance element
Referral route
- Purpose
Escalates symptoms quickly.
- Evidence
OH referral and exposure review.
Read the complete comparison table
| Row | Surveillance element | Purpose | Evidence |
|---|---|---|---|
| 1 | Baseline questionnaire | Records starting respiratory/skin status. | OH health record. |
| 2 | Early follow-up | Detects early sensitisation pattern. | 6-week/6-month style review where applicable. |
| 3 | Annual review | Ongoing detection and trend. | Lung function and questionnaire record. |
| 4 | Skin checks | Identify dermatitis or sensitisation. | Skin surveillance record. |
| 5 | Referral route | Escalates symptoms quickly. | OH referral and exposure review. |
Source comparison
Table ID: isoas-legal-routes
Source: https://www.sharehub.ltd/knowledge-hub/isocyanate-asthma.html
Row 1
- Column 1
Great Britain
- Column 2
COSHH Regulations 2002
- Column 3
Assess the actual isocyanate product and task; prevent or adequately control exposure, maintain controls and use health surveillance where required. Official text and guidance: COSHH Regulations 2002; HSG276 - Isocyanate paint spraying
Row 2
- Column 1
Northern Ireland
- Column 2
COSHH Regulations (Northern Ireland) 2003
- Column 3
Apply the distinct NI hazardous-substances regime and HSENI guidance to spraying, foaming and other exposure routes. Official text and guidance: COSHH Regulations (Northern Ireland) 2003; HSENI COSHH guidance
Row 3
- Column 1
Great Britain
- Column 2
Work-related asthma reporting under GB RIDDOR, where criteria are met
- Column 3
Assess reportability after a medical diagnosis and work link; do not treat a symptom alone as a confirmed statutory case. Official text and guidance: GB RIDDOR reporting guidance
Row 4
- Column 1
Northern Ireland
- Column 2
Reportable occupational disease under the NI reporting regime, where criteria are met
- Column 3
Use the HSENI disease-reporting route after competent diagnosis and a work link; investigate control failure without waiting for a report. HSENI reporting route: HSENI disease reporting.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 |
|---|---|---|---|
| 1 | Great Britain | COSHH Regulations 2002 | Assess the actual isocyanate product and task; prevent or adequately control exposure, maintain controls and use health surveillance where required. Official text and guidance: COSHH Regulations 2002; HSG276 - Isocyanate paint spraying |
| 2 | Northern Ireland | COSHH Regulations (Northern Ireland) 2003 | Apply the distinct NI hazardous-substances regime and HSENI guidance to spraying, foaming and other exposure routes. Official text and guidance: COSHH Regulations (Northern Ireland) 2003; HSENI COSHH guidance |
| 3 | Great Britain | Work-related asthma reporting under GB RIDDOR, where criteria are met | Assess reportability after a medical diagnosis and work link; do not treat a symptom alone as a confirmed statutory case. Official text and guidance: GB RIDDOR reporting guidance |
| 4 | Northern Ireland | Reportable occupational disease under the NI reporting regime, where criteria are met | Use the HSENI disease-reporting route after competent diagnosis and a work link; investigate control failure without waiting for a report. HSENI reporting route: HSENI disease reporting. |
Task-specific HSE control hierarchy
Table ID: isocyanate-asthma-control-priorities
Source: https://www.sharehub.ltd/knowledge-hub/isocyanate-asthma.html
Row 1
- Column 1
Elimination
- Column 2
Check whether a non-isocyanate coating or factory-finished panel meets the customer and product specification so no isocyanate spray is needed.
- Column 3
Owner: purchasing and technical lead. Trial finish and durability; stop if substitute performance or ingredient identity is unverified. HSE task guidance
Row 2
- Column 1
Substitution
- Column 2
Where coating change is possible, test a non-spray brush/roller application or lower-aerosol system using product data; a different two-pack product is not automatically safer.
- Column 3
Owner: competent COSHH assessor. Compare safety data, application and exposure; hold a change that creates uncontrolled solvent or skin risk. HSE task guidance
Row 3
- Column 1
Engineering
- Column 2
Use an enclosed spray booth with appropriate extraction, defined mist-clearance time, filtered air supply and controlled access. Commission airflow, verify clearance, check pressure/filters and exclude bystanders.
- Column 3
Owner: booth engineer and supervisor. Keep test and maintenance evidence; stop for failed extraction, unclear clearance or open access. HSE task guidance
Row 4
- Column 1
Administrative
- Column 2
Use a task COSHH assessment, product identity check, authorised sprayer, cleaning method and observed clearance rule. Biological monitoring and health surveillance check failure; they do not replace exposure prevention.
- Column 3
Owner: supervisor and occupational health. Review results and worker reports; hold spraying after a high result or symptoms until the cause is investigated. HSE task guidance
Row 5
- Column 1
Personal protection
- Column 2
For isocyanate spray mist, select and maintain suitable air-fed respiratory protective equipment and compatible gloves/coveralls. Verify clean air supply, breathing equipment and donning before entry; keep protection on through clearance.
- Column 3
Owner: RPE programme lead and sprayer. Check defects and air supply each task; stop for failed supply, poor fit, damaged equipment or visor lifted in mist. HSE task guidance
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 |
|---|---|---|---|
| 1 | Elimination | Check whether a non-isocyanate coating or factory-finished panel meets the customer and product specification so no isocyanate spray is needed. | Owner: purchasing and technical lead. Trial finish and durability; stop if substitute performance or ingredient identity is unverified. HSE task guidance |
| 2 | Substitution | Where coating change is possible, test a non-spray brush/roller application or lower-aerosol system using product data; a different two-pack product is not automatically safer. | Owner: competent COSHH assessor. Compare safety data, application and exposure; hold a change that creates uncontrolled solvent or skin risk. HSE task guidance |
| 3 | Engineering | Use an enclosed spray booth with appropriate extraction, defined mist-clearance time, filtered air supply and controlled access. Commission airflow, verify clearance, check pressure/filters and exclude bystanders. | Owner: booth engineer and supervisor. Keep test and maintenance evidence; stop for failed extraction, unclear clearance or open access. HSE task guidance |
| 4 | Administrative | Use a task COSHH assessment, product identity check, authorised sprayer, cleaning method and observed clearance rule. Biological monitoring and health surveillance check failure; they do not replace exposure prevention. | Owner: supervisor and occupational health. Review results and worker reports; hold spraying after a high result or symptoms until the cause is investigated. HSE task guidance |
| 5 | Personal protection | For isocyanate spray mist, select and maintain suitable air-fed respiratory protective equipment and compatible gloves/coveralls. Verify clean air supply, breathing equipment and donning before entry; keep protection on through clearance. | Owner: RPE programme lead and sprayer. Check defects and air supply each task; stop for failed supply, poor fit, damaged equipment or visor lifted in mist. HSE task guidance |
Source tables and records 3
Source comparison
Table ID: isocyanate-asthma-activity-control-hierarchy
Source: https://www.sharehub.ltd/knowledge-hub/isocyanate-asthma.html
Row 1
- Column 1
Eliminate
- Column 2
Use suitable prefinished parts or remove unnecessary spray refinishing where the job permits.Basis: HSE isocyanate paint spraying
- Column 3
Task owner verifies that the proposed change removes the named hazardous step, including foreseeable cleaning, maintenance and work transferred elsewhere.
- Column 4
If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
Row 2
- Column 1
Reduce, including substitution
- Column 2
Validate a suitable isocyanate-free coating or non-spray process, checking performance and other hazards.Basis: HSE isocyanate paint spraying
- Column 3
Competent task/process owner validates suitability, compatibility and new hazards against the actual operating requirements before the alternative is adopted.
- Column 4
Reject an alternative if its performance is unproved or its new hazards are unresolved.
Row 3
- Column 1
Isolate
- Column 2
Restrict the spray area and prevent other workers entering during spraying and the verified clearance period.Basis: HSE isocyanate paint spraying
- Column 3
Supervisor checks the actual boundary, affected people and connected work; verify separation or isolation before allowing access.
- Column 4
Hold or stop for failed booth or breathing air, unknown paint, premature entry or unresolved exposure-control failure.
Row 4
- Column 1
Control: physical safeguards
- Column 2
Use a suitable maintained spray booth/room with effective extraction; verify containment and the measured clearance arrangement.Basis: HSE isocyanate paint spraying
- Column 3
Competent equipment/process owner checks paint identity, booth function, clearance period, breathing-air supply and required exposure checks.
- Column 4
Hold or stop for failed booth or breathing air, unknown paint, premature entry or unresolved exposure-control failure.
Row 5
- Column 1
Control: work method and response
- Column 2
Follow the approved spraying and exit/entry procedure, keep required training current and arrange appropriate exposure monitoring and health surveillance.Basis: HSE isocyanate paint spraying
- Column 3
Supervisor confirms the work limits, competent cover, communication and stop/restart authority with the people doing this activity.
- Column 4
Hold work when the agreed limits, competent cover or effective communication cannot be maintained.
Row 6
- Column 1
PPE
- Column 2
Use suitable air-fed breathing apparatus for isocyanate spraying and during the required clearance period, plus compatible skin and eye protection; do not lift the visor early.Basis: HSE isocyanate paint spraying
- Column 3
Assessor confirms whether personal protection is needed and checks suitability, condition, compatibility and any required fit evidence.
- Column 4
Do not use unsuitable protection or rely on PPE to continue after an essential source control fails.
Row 7
- Column 1
Discipline
- Column 2
Check booth, air supply and protective equipment, act on failed monitoring and review product or process changes before reuse.Basis: HSE isocyanate paint spraying
- Column 3
Release only after bodyshop owner verifies the restored booth, air-fed protection and approved work method. Retain verification and unresolved restrictions at handover.
- Column 4
Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Eliminate | Use suitable prefinished parts or remove unnecessary spray refinishing where the job permits.Basis: HSE isocyanate paint spraying | Task owner verifies that the proposed change removes the named hazardous step, including foreseeable cleaning, maintenance and work transferred elsewhere. | If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls. |
| 2 | Reduce, including substitution | Validate a suitable isocyanate-free coating or non-spray process, checking performance and other hazards.Basis: HSE isocyanate paint spraying | Competent task/process owner validates suitability, compatibility and new hazards against the actual operating requirements before the alternative is adopted. | Reject an alternative if its performance is unproved or its new hazards are unresolved. |
| 3 | Isolate | Restrict the spray area and prevent other workers entering during spraying and the verified clearance period.Basis: HSE isocyanate paint spraying | Supervisor checks the actual boundary, affected people and connected work; verify separation or isolation before allowing access. | Hold or stop for failed booth or breathing air, unknown paint, premature entry or unresolved exposure-control failure. |
| 4 | Control: physical safeguards | Use a suitable maintained spray booth/room with effective extraction; verify containment and the measured clearance arrangement.Basis: HSE isocyanate paint spraying | Competent equipment/process owner checks paint identity, booth function, clearance period, breathing-air supply and required exposure checks. | Hold or stop for failed booth or breathing air, unknown paint, premature entry or unresolved exposure-control failure. |
| 5 | Control: work method and response | Follow the approved spraying and exit/entry procedure, keep required training current and arrange appropriate exposure monitoring and health surveillance.Basis: HSE isocyanate paint spraying | Supervisor confirms the work limits, competent cover, communication and stop/restart authority with the people doing this activity. | Hold work when the agreed limits, competent cover or effective communication cannot be maintained. |
| 6 | PPE | Use suitable air-fed breathing apparatus for isocyanate spraying and during the required clearance period, plus compatible skin and eye protection; do not lift the visor early.Basis: HSE isocyanate paint spraying | Assessor confirms whether personal protection is needed and checks suitability, condition, compatibility and any required fit evidence. | Do not use unsuitable protection or rely on PPE to continue after an essential source control fails. |
| 7 | Discipline | Check booth, air supply and protective equipment, act on failed monitoring and review product or process changes before reuse.Basis: HSE isocyanate paint spraying | Release only after bodyshop owner verifies the restored booth, air-fed protection and approved work method. Retain verification and unresolved restrictions at handover. | Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner. |
Source comparison
Table ID: isocyanate-asthma-activity-control-hierarchy-eseap
Source: https://www.sharehub.ltd/knowledge-hub/isocyanate-asthma.html
Row 1
- Column 1
Elimination
- Column 2
Use suitable prefinished parts or remove unnecessary spray refinishing where the job permits.Basis: HSE isocyanate paint spraying
- Column 3
Task owner verifies that the proposed change removes the named hazardous step, including foreseeable cleaning, maintenance and work transferred elsewhere.
- Column 4
If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
Row 2
- Column 1
Substitution
- Column 2
Validate a suitable isocyanate-free coating or non-spray process, checking performance and other hazards.Basis: HSE isocyanate paint spraying
- Column 3
Competent task/process owner validates suitability, compatibility and new hazards against the actual operating requirements before the alternative is adopted.
- Column 4
Reject an alternative if its performance is unproved or its new hazards are unresolved.
Row 3
- Column 1
Engineering controls
- Column 2
Restrict the spray area and prevent other workers entering during spraying and the verified clearance period.Basis: HSE isocyanate paint spraying
- Column 3
Supervisor checks the actual boundary, affected people and connected work; verify separation or isolation before allowing access.
- Column 4
Hold or stop for failed booth or breathing air, unknown paint, premature entry or unresolved exposure-control failure.
Row 4
- Column 1
Engineering controls
- Column 2
Use a suitable maintained spray booth/room with effective extraction; verify containment and the measured clearance arrangement.Basis: HSE isocyanate paint spraying
- Column 3
Competent equipment/process owner checks paint identity, booth function, clearance period, breathing-air supply and required exposure checks.
- Column 4
Hold or stop for failed booth or breathing air, unknown paint, premature entry or unresolved exposure-control failure.
Row 5
- Column 1
Administrative controls
- Column 2
Follow the approved spraying and exit/entry procedure, keep required training current and arrange appropriate exposure monitoring and health surveillance.Basis: HSE isocyanate paint spraying
- Column 3
Supervisor confirms the work limits, competent cover, communication and stop/restart authority with the people doing this activity.
- Column 4
Hold work when the agreed limits, competent cover or effective communication cannot be maintained.
Row 6
- Column 1
PPE
- Column 2
Use suitable air-fed breathing apparatus for isocyanate spraying and during the required clearance period, plus compatible skin and eye protection; do not lift the visor early.Basis: HSE isocyanate paint spraying
- Column 3
Assessor confirms whether personal protection is needed and checks suitability, condition, compatibility and any required fit evidence.
- Column 4
Do not use unsuitable protection or rely on PPE to continue after an essential source control fails.
Row 7
- Column 1
Administrative controls
- Column 2
Check booth, air supply and protective equipment, act on failed monitoring and review product or process changes before reuse.Basis: HSE isocyanate paint spraying
- Column 3
Release only after bodyshop owner verifies the restored booth, air-fed protection and approved work method. Retain verification and unresolved restrictions at handover.
- Column 4
Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Elimination | Use suitable prefinished parts or remove unnecessary spray refinishing where the job permits.Basis: HSE isocyanate paint spraying | Task owner verifies that the proposed change removes the named hazardous step, including foreseeable cleaning, maintenance and work transferred elsewhere. | If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls. |
| 2 | Substitution | Validate a suitable isocyanate-free coating or non-spray process, checking performance and other hazards.Basis: HSE isocyanate paint spraying | Competent task/process owner validates suitability, compatibility and new hazards against the actual operating requirements before the alternative is adopted. | Reject an alternative if its performance is unproved or its new hazards are unresolved. |
| 3 | Engineering controls | Restrict the spray area and prevent other workers entering during spraying and the verified clearance period.Basis: HSE isocyanate paint spraying | Supervisor checks the actual boundary, affected people and connected work; verify separation or isolation before allowing access. | Hold or stop for failed booth or breathing air, unknown paint, premature entry or unresolved exposure-control failure. |
| 4 | Engineering controls | Use a suitable maintained spray booth/room with effective extraction; verify containment and the measured clearance arrangement.Basis: HSE isocyanate paint spraying | Competent equipment/process owner checks paint identity, booth function, clearance period, breathing-air supply and required exposure checks. | Hold or stop for failed booth or breathing air, unknown paint, premature entry or unresolved exposure-control failure. |
| 5 | Administrative controls | Follow the approved spraying and exit/entry procedure, keep required training current and arrange appropriate exposure monitoring and health surveillance.Basis: HSE isocyanate paint spraying | Supervisor confirms the work limits, competent cover, communication and stop/restart authority with the people doing this activity. | Hold work when the agreed limits, competent cover or effective communication cannot be maintained. |
| 6 | PPE | Use suitable air-fed breathing apparatus for isocyanate spraying and during the required clearance period, plus compatible skin and eye protection; do not lift the visor early.Basis: HSE isocyanate paint spraying | Assessor confirms whether personal protection is needed and checks suitability, condition, compatibility and any required fit evidence. | Do not use unsuitable protection or rely on PPE to continue after an essential source control fails. |
| 7 | Administrative controls | Check booth, air supply and protective equipment, act on failed monitoring and review product or process changes before reuse.Basis: HSE isocyanate paint spraying | Release only after bodyshop owner verifies the restored booth, air-fed protection and approved work method. Retain verification and unresolved restrictions at handover. | Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner. |
Source comparison
Table ID: isoas-role-competence
Source: https://www.sharehub.ltd/knowledge-hub/isocyanate-asthma.html
Row 1
- Column 1
Sprayer
- Column 2
Identify product, set booth, use air-fed RPE and respect clearance time.
- Column 3
Supervisor observes a real setup, spray and stop decision.
- Column 4
Authorisation and equipment checks; refresh after product or booth change.
Row 2
- Column 1
Bystander or cleaner
- Column 2
Recognise mist/clearance zones and report symptoms.
- Column 3
Supervisor tests access and cleaning scenario.
- Column 4
Briefing and route; revisit after task change.
Row 3
- Column 1
Supervisor
- Column 2
Check COSHH, booth/air supply, exclusion, monitoring and symptom response.
- Column 3
Competent manager observes hold and restart decision.
- Column 4
Task check and action record; reassess after failure or case.
Row 4
- Column 1
Occupational health and safety specialists
- Column 2
Interpret surveillance, biological monitoring and control data within competence.
- Column 3
Clinical or technical peer reviews a case and controls.
- Column 4
Confidential health and technical records; review on new evidence.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Sprayer | Identify product, set booth, use air-fed RPE and respect clearance time. | Supervisor observes a real setup, spray and stop decision. | Authorisation and equipment checks; refresh after product or booth change. |
| 2 | Bystander or cleaner | Recognise mist/clearance zones and report symptoms. | Supervisor tests access and cleaning scenario. | Briefing and route; revisit after task change. |
| 3 | Supervisor | Check COSHH, booth/air supply, exclusion, monitoring and symptom response. | Competent manager observes hold and restart decision. | Task check and action record; reassess after failure or case. |
| 4 | Occupational health and safety specialists | Interpret surveillance, biological monitoring and control data within competence. | Clinical or technical peer reviews a case and controls. | Confidential health and technical records; review on new evidence. |
Official sources and decisions
Table ID: official-links-table
Source: https://www.sharehub.ltd/knowledge-hub/isocyanate-asthma.html
Row 1
- Column 1
HSE
- Column 2
HSE - Isocyanates in construction
- Column 3
Great Britain
- Column 4
General HSE construction guidance on exposure routes and control of isocyanates.
Row 2
- Column 1
HSE
- Column 2
HSE - Construction isocyanates: spraying
- Column 3
Great Britain
- Column 4
Explains why spraying is high risk and how to assess, control and review exposure.
Row 3
- Column 1
HSE
- Column 2
HSE - Vehicle spray painter
- Column 3
Great Britain
- Column 4
Explains isocyanates in 2K paints, booth clearance, air-fed BA and health surveillance.
Row 4
- Column 1
HSE
- Column 2
HSG276 - Isocyanate paint spraying
- Column 3
Great Britain
- Column 4
Guidance on safely managing spray booths and rooms.
Row 5
- Column 1
HSE
- Column 2
INDG388 - Safety in isocyanate paint spraying
- Column 3
Great Britain
- Column 4
Practical guidance for isocyanate paint spraying.
Row 6
- Column 1
HSE
- Column 2
HSE - Biological monitoring and paint spraying
- Column 3
Great Britain
- Column 4
Explains urine biological monitoring and the importance of checking real exposure control.
Row 7
- Column 1
HSE
- Column 2
HSE - Isocyanates biological monitoring
- Column 3
Great Britain
- Column 4
Explains isocyanate biological monitoring and sampling.
Row 8
- Column 1
HSE
- Column 2
HSE - Health surveillance in motor vehicle repair
- Column 3
Great Britain
- Column 4
Explains respiratory and skin health surveillance for isocyanate-exposed workers.
Row 9
- Column 1
HSE
- Column 2
HSG53 - Respiratory protective equipment at work
- Column 3
Great Britain
- Column 4
Guidance on RPE selection, use and programme management.
Row 10
- Column 1
HSE
- Column 2
INDG479 - RPE fit testing
- Column 3
Great Britain
- Column 4
Guidance on fit testing of tight-fitting RPE.
Row 11
- Column 1
Legislation
- Column 2
COSHH Regulations 2002
- Column 3
Great Britain
- Column 4
GB hazardous-substances duties.
Row 12
- Column 1
Legislation
- Column 2
COSHH Regulations (Northern Ireland) 2003
- Column 3
Northern Ireland
- Column 4
NI hazardous-substances duties.
Row 13
- Column 1
HSENI
- Column 2
HSENI COSHH guidance
- Column 3
Northern Ireland
- Column 4
NI COSHH route.
Row 14
- Column 1
HSE
- Column 2
GB RIDDOR reporting guidance
- Column 3
Great Britain
- Column 4
Reporting criteria for occupational asthma.
Row 15
- Column 1
HSE
- Column 2
HSE five-level control hierarchy
- Column 3
Great Britain
- Column 4
Source removal, substitution, engineering, administration and PPE.
Row 16
- Column 1
HSENI
- Column 2
HSENI - Report a disease (NI2508A)
- Column 3
Northern Ireland
- Column 4
Northern Ireland reportable-disease route, including occupational asthma.
Row 17
- Column 1
HSE
- Column 2
HSE - RPE for vehicle paint spraying
- Column 3
Great Britain
- Column 4
Filtering respirators unsuitable for isocyanate paint spray; air-fed BA selection, APF 20, low-flow warning and half-mask evidence boundary.
Row 18
- Column 1
HSE
- Column 2
HSE: how to manage health and safety
- Column 3
Great Britain
- Column 4
Plan, Do, Check, Act management guidance; use NI law for NI statutory duties.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | HSE | HSE - Isocyanates in construction | Great Britain | General HSE construction guidance on exposure routes and control of isocyanates. |
| 2 | HSE | HSE - Construction isocyanates: spraying | Great Britain | Explains why spraying is high risk and how to assess, control and review exposure. |
| 3 | HSE | HSE - Vehicle spray painter | Great Britain | Explains isocyanates in 2K paints, booth clearance, air-fed BA and health surveillance. |
| 4 | HSE | HSG276 - Isocyanate paint spraying | Great Britain | Guidance on safely managing spray booths and rooms. |
| 5 | HSE | INDG388 - Safety in isocyanate paint spraying | Great Britain | Practical guidance for isocyanate paint spraying. |
| 6 | HSE | HSE - Biological monitoring and paint spraying | Great Britain | Explains urine biological monitoring and the importance of checking real exposure control. |
| 7 | HSE | HSE - Isocyanates biological monitoring | Great Britain | Explains isocyanate biological monitoring and sampling. |
| 8 | HSE | HSE - Health surveillance in motor vehicle repair | Great Britain | Explains respiratory and skin health surveillance for isocyanate-exposed workers. |
| 9 | HSE | HSG53 - Respiratory protective equipment at work | Great Britain | Guidance on RPE selection, use and programme management. |
| 10 | HSE | INDG479 - RPE fit testing | Great Britain | Guidance on fit testing of tight-fitting RPE. |
| 11 | Legislation | COSHH Regulations 2002 | Great Britain | GB hazardous-substances duties. |
| 12 | Legislation | COSHH Regulations (Northern Ireland) 2003 | Northern Ireland | NI hazardous-substances duties. |
| 13 | HSENI | HSENI COSHH guidance | Northern Ireland | NI COSHH route. |
| 14 | HSE | GB RIDDOR reporting guidance | Great Britain | Reporting criteria for occupational asthma. |
| 15 | HSE | HSE five-level control hierarchy | Great Britain | Source removal, substitution, engineering, administration and PPE. |
| 16 | HSENI | HSENI - Report a disease (NI2508A) | Northern Ireland | Northern Ireland reportable-disease route, including occupational asthma. |
| 17 | HSE | HSE - RPE for vehicle paint spraying | Great Britain | Filtering respirators unsuitable for isocyanate paint spray; air-fed BA selection, APF 20, low-flow warning and half-mask evidence boundary. |
| 18 | HSE | HSE: how to manage health and safety | Great Britain | Plan, Do, Check, Act management guidance; use NI law for NI statutory duties. |
Acronyms and meanings
Table ID: isocyanate-asthma-acronyms-and-meanings
Source: https://www.sharehub.ltd/knowledge-hub/isocyanate-asthma.html
Row 1
- Acronym
COSHH
- Meaning
Control of Substances Hazardous to Health
- Plain english use
Regulations and framework for hazardous substance control.
Row 2
- Acronym
RPE
- Meaning
Respiratory Protective Equipment
- Plain english use
Equipment that protects against inhaled exposure.
Row 3
- Acronym
BA
- Meaning
Breathing Apparatus
- Plain english use
Respiratory protection supplied with breathable air.
Row 4
- Acronym
LEV
- Meaning
Local Exhaust Ventilation
- Plain english use
Engineering control to capture airborne contaminants.
Row 5
- Acronym
WEL
- Meaning
Workplace Exposure Limit
- Plain english use
In Great Britain, an approved workplace exposure limit is a legally binding airborne exposure limit. A biological monitoring guidance value is a different control-performance guide, not a WEL. Use the separate NI COSHH route for NI work.
Row 6
- Acronym
OH
- Meaning
Occupational health
- Plain english use
Work-focused health support and surveillance.
Read the complete comparison table
| Row | Acronym | Meaning | Plain english use |
|---|---|---|---|
| 1 | COSHH | Control of Substances Hazardous to Health | Regulations and framework for hazardous substance control. |
| 2 | RPE | Respiratory Protective Equipment | Equipment that protects against inhaled exposure. |
| 3 | BA | Breathing Apparatus | Respiratory protection supplied with breathable air. |
| 4 | LEV | Local Exhaust Ventilation | Engineering control to capture airborne contaminants. |
| 5 | WEL | Workplace Exposure Limit | In Great Britain, an approved workplace exposure limit is a legally binding airborne exposure limit. A biological monitoring guidance value is a different control-performance guide, not a WEL. Use the separate NI COSHH route for NI work. |
| 6 | OH | Occupational health | Work-focused health support and surveillance. |