Chemical storage, compatibility and accidental mixing · detailed source study
Optional reference study from the SHAREhub topic pages and selected source records used for this course. The core learning-time estimate excludes this extended reference.
Stop a wrong connection before substances meet
Stop a wrong connection before substances meet
Source: chemical-compatibility-and-inadvertent-mixing--review-start
A transfer has a sequence of barriers: order identity, delivered product, receiving destination, the complete hose and valve route, segregated connections and the independent check required by the site system. A familiar coupling or colour is only one aid. The receiving owner must be able to stop transfer when identity or route cannot be verified. A transfer has a sequence of barriers: order identity, delivered product, receiving destination, the complete hose and valve route, segregated connections and the independent check required by the site system. A familiar coupling or colour is only one aid. Incompatible materials can react if they meet in storage, transfer lines, drains or waste containers, releasing heat, toxic gas or pressure.
Apply it: Which part of this plan would you check at the workface before authorising the task? Incompatible materials can react if they meet in storage, transfer lines, drains or waste containers, releasing heat, toxic gas or pressure. Prevent the encounter through verified identity, segregation and engineered transfer barriers. Monthly review and change trigger. Apply it: What evidence would show that the change improves this task, rather than only completing a record? Chemical register: Compatibility class, SDS section 10, storage, owner and approved use. Evidence / response: Monthly review and change trigger. Transfer verification: Right product, tank, hose, valve lineup and ullage confirmed. Evidence / response: Operator checklist and supervisor sample.
Apply it: At which point would you hold this example, and what evidence would allow it to proceed? Unlabelled containers: Wrong use, wrong disposal or wrong first response. Shared hoses or funnels: Cross-contamination between incompatible substances. Similar fill points: Wrong-tank transfer. Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby? Elimination: Remove an unnecessary product or cleaning step so bleach and acid do not need to be used together in the task. Substitution: Trial an effective less reactive cleaning product or method after reviewing its full hazard profile. Engineering controls: Store incompatible products separately in suitable containment and keep dedicated, clearly identified dispensing equipment. Engineering controls: Use compatible closed dispensing arrangements; prevent cross-connections, shared funnels and return of contaminated product.
Administrative controls: Follow the approved sequence and product instructions; verify the surface and container are suitable before a different chemical is introduced. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged. Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk? Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status. Apply it: Which official source and full-topic section will you use to resolve the next decision?
Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links. A transfer has a sequence of barriers: order identity, delivered product, receiving destination, the complete hose and valve route, segregated connections and the independent check required by the site system. A transfer has a sequence of barriers: order identity, delivered product, receiving destination, the complete hose and valve route, segregated connections and the independent check required by the site system. A familiar coupling or colour is only one aid. Incompatible materials can react if they meet in storage, transfer lines, drains or waste containers, releasing heat, toxic gas or pressure.
Apply it: Which part of this plan would you check at the workface before authorising the task? Use the evidence to improve the actual work arrangement. Incompatible materials can react if they meet in storage, transfer lines, drains or waste containers, releasing heat, toxic gas or pressure. Prevent the encounter through verified identity, segregation and engineered transfer barriers. Monthly review and change trigger. Apply it: What evidence would show that the change improves this task, rather than only completing a record? Fictional example: a practical application of the existing topic lesson. Chemical register: Compatibility class, SDS section 10, storage, owner and approved use. Evidence / response: Monthly review and change trigger. Transfer verification: Right product, tank, hose, valve lineup and ullage confirmed.
Evidence / response: Operator checklist and supervisor sample. Apply it: At which point would you hold this example, and what evidence would allow it to proceed? Connect the task, the route to the person and the control that can fail. Unlabelled containers: Wrong use, wrong disposal or wrong first response. Shared hoses or funnels: Cross-contamination between incompatible substances. Similar fill points: Wrong-tank transfer. Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby? Start with the stronger practicable options and verify their effect. Elimination: Remove an unnecessary product or cleaning step so bleach and acid do not need to be used together in the task. Substitution: Trial an effective less reactive cleaning product or method after reviewing its full hazard profile.
Engineering controls: Store incompatible products separately in suitable containment and keep dedicated, clearly identified dispensing equipment. Engineering controls: Use compatible closed dispensing arrangements; prevent cross-connections, shared funnels and return of contaminated product. Administrative controls: Follow the approved sequence and product instructions; verify the surface and container are suitable before a different chemical is introduced. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged. Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk? Follow the official sources below and retain the task-specific evidence. Use the full topic for the decision points, practical examples, detailed control tables and source scope.
HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status. Apply it: Which official source and full-topic section will you use to resolve the next decision? Simplified learning guide. Use the full topic and the actual work arrangements; existing technical-review and approval statuses still apply. Workplace scenarios labelled fictional are illustrative examples. Apply the same reasoning to waste. An unlabelled drum or uncertain drain contents cannot be approved from a compatibility chart, because composition, residues and reaction conditions remain unknown. Keep the container or route isolated under the site plan and obtain competent investigation.
Do not test compatibility by pouring in a small amount or attempting neutralisation. Illustrative example. A fictional delivery reaches a connection that fits, but the receiving label and order do not agree. Decision. The operator stops before transfer; the receiving owner and independent checker trace the material and destination against current site information. Evidence to check. Order and delivery identity, destination and ullage, route walkdown and the required independent check. Hold or escalation point. Do not transfer while identity, route or residues are uncertain, including for a partially filled waste container. Follow-up. Investigate how the mismatch reached the gate and improve labels, connections or delivery checks before reuse. Read with: HSE chemical waste treatment · HSE using chemicals at work · HSE COSHH assessment.
Trace the product all the way to the destination
Trace the product all the way to the destination
A familiar container or hose colour cannot confirm compatibility. Check the order, material, receiving system and every connection before authorising transfer. Match delivered product to the order and receiving destination, including concentration, available capacity and known residues. Trace hoses, valves and connections through the actual system and use any independent verification required by the assessed method. Keep unknown waste or conflicting identity/compatibility evidence on hold for competent acceptance. Do not use a universal mixing matrix as permission. The schematic provides no chemical-mixing recipe, connection procedure or compatibility approval. Further guidance: HSE: COSHH assessment.
What are the key facts about chemical compatibility and inadvertent mixing?
Source: chemical-compatibility-and-inadvertent-mixing--key-facts
The key facts are that incompatible chemicals can react violently or invisibly, and the wrong connection, drain or waste container can be enough to start the event.
What is chemical compatibility and inadvertent mixing?
Source: chemical-compatibility-and-inadvertent-mixing--what-is-it
Chemical compatibility is the safe relationship between substances, and inadvertent mixing is the accidental combination of substances that should have been kept apart. Compatibility is not simply whether two products sit on the same shelf without reacting. It includes storage, handling, transfer, use, cleaning, waste disposal, drainage, emergency response and foreseeable abnormal situations such as leaks, wrong deliveries, overfills, rainwater ingress and equipment failure. Inadvertent mixing can happen in ordinary workplaces: a cleaner mixes bleach and acid descaler, a worker pours waste into the wrong container, or a contractor uses an unapproved product in a drain. It can also happen in process industries: a road tanker connects to the wrong fill line, a transfer route is mis-valved, or incompatible waste is bulked in a tank.
The management task is to make the right action easier than the wrong one. That means clear naming, different connections, segregated storage, dedicated containers, locked or interlocked routes, independent verification and a culture where uncertainty stops the job.
What reactions can incompatible chemicals cause?
Source: chemical-compatibility-and-inadvertent-mixing--reaction-types
Incompatible chemicals can generate toxic gas, heat, pressure, fire, explosion, corrosive release, unstable products or environmental contamination. The most recognised example is acid mixed with sodium hypochlorite bleach, which can release chlorine gas. Other examples include acids with cyanides or sulphides producing toxic gases, oxidisers with organic or flammable materials increasing fire risk, and water-reactive substances producing heat or flammable gas. Some reactions are immediate and obvious; others develop in a waste container, drain, bund or tank after people leave. Heat, bulging drums, hissing, discolouration, unexpected odour, gas, foaming, pressure rise or unusual crystallisation should be treated as warning signs.
A compatibility assessment should consider chemical family, concentration, quantity, temperature, impurities, water, pH, contaminants, container material and the consequences if the mixture occurs in a confined or enclosed space. A hazard-class storage chart is only a starting point. HSE HSG71, paragraph120 warns that substances grouped as compatible can still react; its examples include acid with hypochlorite, cyanide, sulphide or alkali. Check the actual products, residues and leak/drain paths using SDS and competent chemistry advice. This 2009 guidance supports the reaction/segregation principles; its historical legislative references are not the current supply-law route.
Where does inadvertent mixing usually happen?
Source: chemical-compatibility-and-inadvertent-mixing--where-it-happens
Inadvertent mixing usually happens where identification, segregation, transfer control, waste approval, drain management or supervision is weak. Compatibility failures are often created by ordinary decisions: a substance is decanted into an unlabelled bottle, a shared funnel is used, a hose is left connected, a drain receives several discharges, or a waste drum becomes the convenient place for everything. Bulk transfer adds more serious potential. Similar fill points, unclear pipework, missing line labels, shared couplings, poor lighting, driver unfamiliarity, weak handover or no independent verification can put the wrong chemical into a tank. If the receiving tank contains an incompatible substance, the reaction can escalate quickly. Maintenance and cleaning are also high-risk because equipment may contain residues.
A vessel, drain, sump or line can look empty but still contain enough substance to react with a cleaner, rinse, purge or next batch.
How is this different in ordinary workplaces and higher-risk process sites?
Source: chemical-compatibility-and-inadvertent-mixing--ordinary-high-risk
Ordinary workplaces usually focus on storage, labels, cleaning chemicals and waste, while higher-risk sites also need engineered transfer safeguards and major accident barriers. In a school, leisure centre, office, workshop or small warehouse, the main concerns may be cleaning products, pool chemicals, battery acid, aerosols, small flammable stores, incompatible waste and unlabelled bottles. The controls should be simple, visible and disciplined. In chemical plants, fuel terminals, water treatment, laboratories, manufacturing, waste treatment and COMAH establishments, compatibility can become a major accident hazard. Wrong transfers, incompatible bulk storage, reactive residues or misdirected drains can create toxic release, fire, explosion, overpressure or off-site consequences. The page is therefore useful at two levels. Everyone needs to stop incompatible chemicals meeting.
Higher-risk operators must also prove that safety critical barriers are identified, owned, tested, maintained and reviewed.
How should chemical compatibility be assessed?
How should chemical compatibility be assessed?
Source: chemical-compatibility-and-inadvertent-mixing--assessment
Compatibility should be assessed by reviewing the chemical inventory, SDS information, reaction hazards, storage locations, transfer routes, drains, waste streams and credible mixing scenarios. Start with the inventory. List all chemicals, wastes, residues, cleaning chemicals, intermediates, off-spec materials and process fluids. Then identify what could meet what: shelves, bunds, drains, hoses, fill points, waste containers, shared equipment, cleaning routines and emergency response materials. The SDS is important, especially sections on handling, storage, stability and reactivity, but it does not know your pipework, drain route, container choices or work sequence. A site-specific compatibility review should connect the SDS with the physical workplace.
For higher-risk operations, create credible scenarios: acid into hypochlorite tank, oxidiser into solvent waste, wrong road tanker connection, incompatible drain discharge, cleaning chemical into process residue, rainwater into water-reactive store, or waste drum bulking error.
How can the ISO 45001 hierarchy of controls reduce risks while assessing drums before chemical-waste bulking?
Source: chemical-compatibility-and-inadvertent-mixing--controls
Incompatible mixing should be prevented through elimination, substitution, segregation, engineered design, verified transfer, controlled waste routes, training and disciplined supervision. ERICPD applies well. Eliminate unnecessary substances or mixing tasks. Reduce quantities and concentrations. Isolate incompatible chemicals physically. Control routes through dedicated containers, hoses, couplings, fill points, valves, drains and waste approvals. Use PPE for residual exposure. Discipline holds the system together through checks, permits, handovers and learning. The most reliable controls reduce the chance of human error. Different connector types, locked fill points, keyed transfer routes, clear labels, colour coding, barcode verification, interlocks and independent checks can all make wrong transfer less likely. Where controls rely on people, make the task easy to do correctly.
Labels should be visible, names consistent, lighting adequate, procedures short enough to use, and stop-work authority real. Choose the activity that matches the work. Each has its own controls, verification and stop/restart decisions; ERICPD and ISO 45001 are alternative views of that same activity. A cleaning team holds bleach and acidic descaler for separate jobs; residues, shared bottles and contractor products can create an unintended reaction. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level. The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation"). ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE.
Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance. Two waste drums are proposed for a combined collection. Do not use appearance or a broad waste description as proof of compatibility. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level. The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation"). Use HSE’s five-level hierarchy to choose stronger measures before PPE. ERICPD is a useful six-part teaching mnemonic; it is not a separate legal test. The example maps both approaches to the real task. Apply HSENI COSHH guidance for a Northern Ireland workplace.
Emergency washing and evacuation limit consequences; they do not prevent the original contact or mixing.
How should deliveries and transfers be verified?
Source: chemical-compatibility-and-inadvertent-mixing--transfer
Identify the substance, tank and connection independently before opening a transfer path; stop if any identity or barrier is uncertain. Compare the order, delivery note, container/tank label, SDS and authorised route. A receiving operator should verify the fixed tank and line against a current line map, while the driver checks the vehicle and hose. Dedicated or non-interchangeable couplings, locked and labelled fill points and suitable interlocks protect against a plausible wrong connection. Treat a missing label, unlocked alternative fill line, bypassed interlock or disagreement as a stop condition. The US CSB MGPI case illustrates why a verbal confirmation alone cannot compensate for confusing fill-point design.
How should incompatible chemicals be stored and segregated?
Source: chemical-compatibility-and-inadvertent-mixing--storage
Chemicals should be stored so leaks, breakages, fire water, rainwater, vapours or container failure cannot bring incompatible substances together. Segregation should be based on real compatibility, not only alphabetic order or convenience. Acids and alkalis should normally be separated; oxidisers should be separated from flammables and combustibles; toxic, cyanide, sulphide, water-reactive and peroxide-forming materials may need specialist controls. Secondary containment matters. If two incompatible liquids share the same bund, they may mix when containers leak. If chemicals are stacked with incompatible materials above or below each other, a leak can drip into the wrong class. Storage must be maintained: labels legible, containers closed, shelves compatible, spill kits suitable, expired or unstable chemicals removed, and stock levels controlled.
A hazard-class storage chart is only a starting point. HSE HSG71, paragraph120 warns that substances grouped as compatible can still react; its examples include acid with hypochlorite, cyanide, sulphide or alkali. Check the actual products, residues and leak/drain paths using SDS and competent chemistry advice. This 2009 guidance supports the reaction/segregation principles; its historical legislative references are not the current supply-law route.
Why are waste streams and drains high-risk mixing routes?
Why are waste streams and drains high-risk mixing routes?
Source: chemical-compatibility-and-inadvertent-mixing--waste-drains
Waste streams and drains are high-risk because chemicals can meet out of sight after leaving the original task area. A drain, sump, interceptor, IBC, drum or waste tank can become the mixing vessel. Workers may think each individual disposal was small, but incompatible discharges can accumulate or react in a confined space, generating heat, pressure, gas or pollution. Waste compatibility needs a positive approval process. Unknown waste should not be bulked because it looks similar or because the container is available. Waste labels should include contents, hazards, source, date, incompatible materials and owner. Drain maps and isolation points are important for process sites, laboratories, workshops and construction sites.
If responders do not know where a drain goes, they cannot confidently control a spill or incompatible discharge.
What if incompatible chemicals are mixed?
Source: chemical-compatibility-and-inadvertent-mixing--emergency
Stop the task, move people away and activate the site emergency plan; do not approach a reacting container or improvise a neutraliser. Heat, pressure, hissing, gas, bubbling, bulging, new odour or unexpected colour are stop-and-evacuate cues. Call 999 when there is a suspected toxic release, fire, explosion, serious injury or threat beyond local control. Trained responders need substance identity, SDS, inventory, drainage and site plan. Shut off remotely only where the procedure makes that safe. Untrained staff must not enter a plume, move a bulging container, pour another chemical into it or clean up before the incident is made safe. Reopen only after competent investigation and barrier repair.
Which major accident barriers control compatibility and inadvertent mixing?
Source: chemical-compatibility-and-inadvertent-mixing--barriers
Major accident barriers should prevent, detect, control and mitigate wrong-substance mixing before it becomes toxic release, fire, explosion, overpressure or escalation. For process safety, a compatibility failure should be placed on the major accident hazard register where it could cause a serious release. The register should state the scenario: for example, acid transferred into hypochlorite tank, oxidiser into solvent waste, incompatible drainage discharge, or wrong raw material charged to a reactor. Barriers should be named and owned. A label is a barrier only if it is maintained, visible and understood. A procedure is a barrier only if people can use it under real delivery conditions. An interlock is a barrier only if it is tested and managed through change control. Assurance evidence matters.
If the same fill point has confusing labels, repeated near misses or drivers asking which line to use, the barrier is degraded even if the paperwork says the system exists.
Which duties apply to chemical compatibility?
Source: chemical-compatibility-and-inadvertent-mixing--legal
Assess hazardous exposure and fire/reactivity for the actual site; COMAH adds major-accident duties only where an establishment is in scope. COSHH 2002 in GB and COSHH (NI) 2003 in NI cover hazardous exposure from stored and mixed substances. Dangerous-substance and fire/explosion law also requires location-specific assessment. An establishment at or above the relevant COMAH threshold quantities, subject to the scope rules, needs major-accident prevention and emergency arrangements under its GB or NI instrument; ordinary workplaces still need proportionate compatibility control. SDS information is an input, not a substitute for testing or a task-specific assessment of wastes and process conditions.
How could Crownway Fuels Ltd manage chemical compatibility and inadvertent mixing?
Source: chemical-compatibility-and-inadvertent-mixing--business-example
Crownway Fuels Ltd could manage compatibility by linking its chemical register, tank farm controls, transfer verification, waste routes, drain maps, emergency planning and barrier assurance. For this example, Crownway Fuels Ltd operates a fuel storage and distribution site using additives, cleaners, treatment chemicals, laboratory reagents, waste oils, interceptor waste and contractor maintenance chemicals. Crownway starts by building a compatibility register from SDS information, process knowledge and waste-stream data. Each chemical has an owner, storage location, incompatible classes, approved transfer route, drain controls, PPE/RPE, emergency response and disposal route. New chemicals cannot be purchased or brought on site until compatibility, DSEAR and COSHH reviews are complete. Bulk transfer is controlled as a safety critical activity.
Fill points are physically labelled, colour coded and mechanically different where possible. Operators verify delivery paperwork, tank identity, ullage, valve lineup, hose route, drain protection and emergency stop arrangements before transfer. Higher-consequence transfers need independent verification and post-transfer reconciliation. Waste and drains are managed deliberately. Waste oils, oily water, lab wastes, cleaning residues and interceptor contents have approved containers and no unknown bulking rule. Drain maps show where surface water, foul drains and containment routes go. Spill drills include drain isolation because a compatibility event can travel through drainage before responders realise.
Crownway checks the system at several levels: operators use binary transfer checks, supervisors sample transfer observations, HSSE audits chemical stores and waste areas, and leadership reviews near misses such as unclear labels, rejected deliveries, wrong hose attempts, odour complaints or blocked drain valves. Learning changes equipment, labels, procedures, procurement and training.
What can fuel-transfer interfaces teach about incompatible mixing?
What can fuel-transfer interfaces teach about incompatible mixing?
Source: chemical-compatibility-and-inadvertent-mixing--crownway-atex-example
Trace the receiving path and selected product before considering transfer controls. A plausible hose connection does not establish compatibility or correct product identity. During the proposed tanker delivery, product enters the receiving tank and displaced vapour returns to the tanker by a separate path. The delivery-hose teaching envelope follows the connected hose route. Activity focus: Trace the tanker connection, product hose and receiving fill before following the Stage 1b vapour-return path. Inspect the whole delivery working area, including nearby traffic, dispensers and drainage. Contextual workplace scene. Use the task, control and evidence checks in this section; appearance alone does not establish safe conditions, individual health or approval.
Follow petrol from bulk storage into the tanker and the separate displaced-vapour route from the tanker to the terminal VRU. Activity focus: Distinguish the product line, vapour collection line and tanker-loading protective controls. Contextual workplace scene. Use the task, control and evidence checks in this section; appearance alone does not establish safe conditions, individual health or approval. Educational illustration, not to scale. Coloured zones are teaching examples, not a site-specific hazardous-area classification. Basis and limits: Unloading petrol from road tankers: L133 · Petrol dispensing premises: DSEAR risk assessments, GN75 · Defra: storage, unloading and loading petrol at terminals — PG1/13(13) · Functional safety: SIS, alarms and basic process control · Overfill of vapour recovery units: safety notice
What should each role learn and demonstrate?
Source: chemical-compatibility-and-inadvertent-mixing--training
Learning must match the decisions people make, from recognising danger to checking that controls work. Briefings should tell people how to act, but attendance alone does not show competence. Assess the real decision or task, record who assessed it and revisit after a material change, failed control or incident. A local authorisation is task-specific; no universal external certificate is implied.
How does this topic support process safety and IOSH study?
Source: chemical-compatibility-and-inadvertent-mixing--study-development
This topic supports study by connecting chemical information, storage, transfer verification, human factors, emergency control and major accident barriers. For process safety learners, compatibility is a strong example of a simple initiating event creating major consequences. The exam or scenario may describe wrong transfer, poor labelling, similar connections, no independent check, incompatible waste, unclear procedures or a delayed emergency response. Good answers should identify the reaction consequence, the failed barriers, the controls needed before transfer, and the evidence that the system is healthy. A strong response does not simply say 'train workers'; it explains physical segregation, engineered compatibility, line identification, unique couplings, interlocks, emergency stops, drain isolation and verification.
For broader health and safety learners, the topic reinforces COSHH, DSEAR, SDS use, storage segregation, PPE, emergency arrangements and contractor control.
How can a management system sustain effective decisions?
Source: chemical-compatibility-and-inadvertent-mixing--management-system
Give each hazard or support route an owner, a control, a check and a response to failure. Assign each storage, transfer and waste barrier an owner, performance test and failure response. Sample a real fill point and drain route, then trace any near miss into engineering change and verified repair. An owner should sample actual work and corrective actions, not accept a policy or certificate as evidence that the controls work. The free GB regulator guide HSE Managing for health and safety (HSG65) explains a plan–do–check–act approach: assign controls and owners, involve workers, check work as done, and correct failures. For Northern Ireland, use HSENI risk assessment guidance for the local duty. A certificate alone does not demonstrate that a control works.
Which major incidents show why inadvertent mixing controls matter?
Source: chemical-compatibility-and-inadvertent-mixing--major-learning
The MGPI Processing incident shows how a wrong chemical transfer can create toxic release, community impact and clear lessons for transfer design and verification. In October 2016, at the MGPI Processing facility in Atchison, Kansas, sulphuric acid was unloaded into a sodium hypochlorite tank. The incompatible substances reacted and produced a chlorine-containing cloud. The release affected workers and the surrounding community, with many people seeking medical treatment and shelter-in-place or evacuation actions used locally. The direct lesson is not simply that a driver used the wrong connection. The wider process-safety lesson is that similar-looking fill lines, unclear physical differentiation, weak transfer verification, insufficient safeguards and unclear responsibilities can make wrong transfer foreseeable.
Stronger barriers include clear labelling, dedicated/unique connections, independent verification, emergency shut-off, procedures agreed with suppliers and emergency response planning. UK sites should use the learning carefully: check whether their own bulk delivery, waste bulking, tank filling, drain discharge or cleaning operations rely too heavily on one person's attention.
What are the warning signs that compatibility controls are weak?
What are the warning signs that compatibility controls are weak?
Source: chemical-compatibility-and-inadvertent-mixing--warning-signs
Warning signs include unlabelled containers, shared hoses, similar fill points, unclear waste streams, poor drain knowledge, incompatible storage and workers improvising chemical disposal. Weak compatibility control usually leaves clues. A store may have acids above alkalis, oxidisers beside flammables, expired chemicals in corners, unlabelled jugs, full spill trays, or waste drums labelled only as 'chemical waste'. A transfer area may have several identical connections and no physical prevention of wrong hose connection. The harm pathway should be explicit. A wrong container can lead to wrong disposal. A shared hose can cross-contaminate substances. A shared bund can mix leaks. An unknown waste drum can over-pressurise. An unprotected drain can carry incompatible chemicals to a confined sump.
Every warning sign should trigger a system fix: stop use, identify contents, segregate, relabel, redesign, review the SDS, update the compatibility matrix, brief workers and verify action close-out.
Use the chemical system to control a changed task
Source: chemical-safety--review-start
A purchased cleaner needs supplier information plus an assessment of dilution, use, ventilation, contact, storage and disposal. A fume created by heating material needs evidence about the material and process. Both sit in the chemical system, but a product inventory or SDS library cannot replace either task assessment. Use change as the connecting journey through the specialist guides. A different cleaner, contractor method or work temperature can alter exposure, reactivity, storage, emergency arrangements and competence. Assign one operational owner to bring those reviews together before use, with the relevant COSHH, compatibility, classification and fire/explosion routes kept distinct. Determine reporting separately from emergency control; a spill is not automatically a statutory report. Illustrative example.
A fictional contractor proposes a warmer cleaning process with a replacement product already used at another site. Decision. The contract and chemical owners review the changed material and conditions before accepting the method. Evidence to check. Current product information, actual temperature and exposure, compatibility, storage, waste route and emergency capability. Hold or escalation point. Hold use while introduced risks or changed controls remain unresolved. Follow-up. Update the approved use, contractor briefing and control checks so the substitute does not become an unreviewed routine. Read with: HSE using chemicals at work · HSE COSHH basics · HSE COSHH assessment.
Separate a vapour release from a powder release
Source: chemical-safety--practical-chemical-safety
Enclosed cleaning and powder charging need controls matched to their material, process and release route. A single generic chemical-safety checklist will not settle both. Check the substance, mixture and task, including cleaning, maintenance and waste handling. Assess the enclosure, capture point and people’s positions for vapour or dust as appropriate. Keep hands clear of machinery and retain its separate energy controls. Check actual control performance, suitable protection and the waste route. A failed source control returns the affected task to hold. This is a comparison of assessment questions, not a solvent choice, mixer operating method or exposure clearance. Further guidance: HSE: COSHH assessment.
What are the key facts about chemical safety?
Source: chemical-safety--key-facts
The key facts are that chemical harm depends on the substance, its form, the exposure route, the dose, the task and whether controls are reliable.
Explore this topic in a working scene
Source: chemical-safety--share-simulate-scene
Try 1 scenario with images, explanations and decisions that develop into follow-on situations. Trace how a hazard can cause harm, compare work arrangements and choose controls. Practice progress saves on this device. Fictional outcomes illustrate decisions; completion does not certify competence.
What is chemical safety at work?
Source: chemical-safety--what-is-it
Chemical safety is the practical system used to prevent people, property and the environment being harmed by chemicals and substances hazardous to health. Good chemical safety starts before a substance is purchased. A business should ask whether the substance is needed, whether a safer option exists, what it will be used for, who will use it, how exposure could occur and how the substance will be stored, moved, controlled and disposed of. The term chemical should be read broadly. It includes cleaning products, paints, adhesives, fuels, solvents, acids, alkalis, resins, disinfectants, laboratory reagents, process chemicals and substances generated by work such as welding fume, wood dust, silica dust, metalworking fluid mist or diesel exhaust. A strong page or system should not stop at the label.
It should connect classification, toxicology, fire and reaction hazards, exposure route, work method, control reliability, maintenance, emergency planning, training and evidence.
What forms can hazardous substances take?
What forms can hazardous substances take?
Source: chemical-safety--forms
Hazardous substances can appear as gases, vapours, fumes, mists, aerosols, dusts, powders, liquids, pastes, solids, fibres and biological agents. The physical form changes the exposure route and the control method. A volatile solvent may create an inhalation and fire risk. A corrosive liquid may create splash and skin-burn risks. A fine powder may become airborne during pouring or mixing. A hot process may create fume even if the original material seemed stable. Chemicals can also change form during use. Spraying turns liquids into aerosols. Heating can produce vapours or decomposition products. Grinding, cutting or sanding can turn solid materials into respirable dust. Mixing incompatible substances can create heat, gas, pressure or toxic release.
The COSHH assessment should name the form present during the task, not just the product name. This is often where weak assessments fail.
How can chemicals enter or affect the body?
Source: chemical-safety--routes
Chemicals can harm people through inhalation, skin contact, skin absorption, eye contact, ingestion and injection. Inhalation is often the most obvious route because airborne dusts, gases, vapours, mists and fumes can reach the nose, throat and lungs. Fine respirable particles can travel deep into the lungs; soluble gases may irritate the upper airways; some vapours can be absorbed into the bloodstream. Skin exposure is often underestimated. Some substances damage the skin surface, some pass through the skin and affect organs, and some cause sensitisation so that later small exposures trigger a reaction. Wet work, damaged gloves, contaminated sleeves, trapped chemicals and poor washing facilities all increase risk. Eye exposure, ingestion and injection are less frequent but can be severe.
Splash injuries, contaminated hands near the mouth, eating in work areas and puncture injuries from contaminated sharps or high-pressure injection equipment should be considered in the assessment.
What health effects can chemical exposure cause?
Source: chemical-safety--health-effects
Chemical exposure can cause immediate injury, delayed illness, sensitisation, cancer, reproductive harm, organ damage, respiratory disease, skin disease and poisoning. Some chemical effects happen quickly: burns, eye injury, dizziness, breathing difficulty, irritation, unconsciousness or acute poisoning. Others develop slowly after repeated exposure or after a long latency period, such as occupational asthma, dermatitis, chronic lung disease or cancer. Dose and duration matter, but so does individual susceptibility. A sensitiser may cause one worker to develop allergic asthma or dermatitis while another worker appears unaffected. Once sensitised, future low exposures may trigger symptoms. Chemical health risk should be read alongside fire, explosion and environmental risk.
A flammable solvent, for example, may require COSHH controls for inhalation and skin exposure, DSEAR controls for explosive atmospheres, and environmental controls for spills and drainage.
How should labels and safety data sheets be used?
Source: chemical-safety--labels-sds
Use the current product label and SDS to understand supply hazards, then assess the real task before work starts. Confirm product identity, formulation and revision. Check exposure, first aid, fire, stability and incompatibility sections against the method, quantity, temperature, by-products and people nearby. The SDS does not assess this specific work and may not describe process-generated dust or fume. Hold use when identification or information conflicts; the supplier and competent assessor should resolve it.
How do REACH and CLP fit with workplace chemical safety?
Source: chemical-safety--reach-clp
Supply classification and registration depend on the destination market; workplace COSHH controls depend on the actual site and task. GB CLP and UK REACH apply to the Great Britain supply route. EU CLP and EU REACH continue in Northern Ireland. The supplier or importer must check its role and current market rules. The workplace user still needs a separate COSHH assessment and effective controls; an SDS or pictogram is not the completed assessment.
How should chemical safety be assessed?
Source: chemical-safety--assessment
Chemical safety should be assessed by identifying substances, tasks, exposure routes, people exposed, health effects, fire or reaction hazards and the controls needed to prevent harm. A good assessment starts with a chemical inventory and task review. List what is used, generated or stored, then look at the task: quantity, concentration, temperature, duration, frequency, method of application, ventilation, nearby people, maintenance activities, cleaning and waste. The assessment should separate hazard from risk. A substance can be hazardous but low risk if it is sealed in a closed system with no credible exposure. A lower-hazard product can become higher risk if sprayed, heated, used for long periods or used in a poorly ventilated space.
The assessment should also cover foreseeable abnormal situations: spills, wrong chemical added, failed extraction, missing RPE, incompatible storage, contractor use, emergency cleaning, unlabelled containers, damaged packaging and waste accumulation.
How can the ISO 45001 hierarchy of controls reduce risks while charging bagged powder into a mixer?
How can the ISO 45001 hierarchy of controls reduce risks while charging bagged powder into a mixer?
Source: chemical-safety--controls
Chemical exposure should be controlled by eliminating or substituting hazards, enclosing processes, controlling emissions at source, using safe systems and adding PPE only where residual risk remains. ERICPD helps keep control thinking practical. Eliminate the chemical or task where possible. Reduce risk through safer substitutes, lower concentration, smaller quantities, pellets instead of powder, lower temperature or shorter exposure. Isolate people using enclosures, segregation and restricted access. Control emissions using LEV, closed transfer, automation, cleaning and emergency systems. PPE and RPE then protect against remaining exposure. Discipline keeps the controls used, maintained and checked. Control also needs to match the route of exposure. LEV will not protect skin from a corrosive liquid. Gloves will not control vapour. A respirator will not make incompatible storage safe.
Good chemical safety often needs several layers working together. The standard should be good practical control, not paperwork compliance. If the work still smells strongly of solvent, creates visible dust, leaves chemical residue on benches, relies on torn gloves or has workers unsure what to do in a spill, the control system is not mature. Choose the activity that matches the work. Each has its own controls, verification and stop/restart decisions; ERICPD and ISO 45001 are alternative views of that same activity. A maintenance team cleans known oily components before assembly; identify solvent, contamination, ignition and skin-contact hazards. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.
The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation"). ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance. An operator empties identified powder ingredients into a mixer; assess inhalation, skin contact and any combustible-dust hazard. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level. The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation"). Use HSE’s five-level hierarchy alongside ERICPD, a complementary teaching mnemonic rather than a separate legal test.
Physical measures change the plant or exposure pathway; instructions and checks change how people work. Apply HSENI COSHH guidance for a Northern Ireland workplace. The following is a worked task example, not a universal plant specification.
How should chemicals be stored and segregated?
Source: chemical-safety--storage
Chemicals should be stored in labelled compatible containers, segregated by hazard, protected from damage and supported by spill, fire and emergency arrangements. Storage is not just housekeeping. Poor storage can turn normal chemical use into fire, toxic release, uncontrolled reaction, environmental pollution or exposure during clean-up. Chemical stores should be designed around compatibility, ventilation, containment, access control, temperature, ignition control and emergency access. Incompatible chemicals should be separated so that leaks, container failures or mistaken mixing do not create dangerous reactions. Acids and alkalis, oxidisers and flammables, water-reactive substances and water, and chemicals that release toxic gases when mixed should be clearly controlled. Stock should be managed. Old chemicals, unlabelled containers, decanted bottles, damaged drums and excess quantities all increase risk.
A chemical register should show what is present, where it is kept, who owns it and whether the SDS and assessment are current.
What emergency arrangements are needed for chemicals?
Source: chemical-safety--emergency
Plan for the credible release, eye or skin contact, fire and incompatible mixing before the work begins. Stop the task and move people away from an uncontrolled release. Call 999 for serious injury, toxic-gas release, fire or an incident beyond site control. Do not send untrained people into a plume or improvise chemical neutralisation. First aid depends on the substance and current clinical advice; provide responders with the product identity, SDS and exposure details. A competent person should verify containment, isolation, communication and restart conditions.
How should chemical controls be monitored and maintained?
How should chemical controls be monitored and maintained?
Source: chemical-safety--monitoring
Chemical controls should be checked through routine workplace inspections, user checks, LEV testing, exposure monitoring, supervision, health surveillance and management review. Active monitoring confirms whether controls are present before harm occurs. Frontline checks might confirm labels, storage, spill kits, gloves, RPE, eyewash and extraction are available and used. Supervisor checks should look at the quality of work methods. Specialist checks may include LEV examination, exposure monitoring or occupational hygiene review. LEV requires particular attention because it can look impressive while failing to capture contaminants. Hood position, airflow, draughts, damage, blocked filters, poor user technique and process changes can all undermine protection. Monitoring should generate action, not just scores.
If repeat checks show missing SDSs, full cabinets, poor glove use or workers unsure about spill response, the system should trigger improvement, not another identical checklist.
When is health surveillance needed for chemicals?
Source: chemical-safety--surveillance
Health surveillance is needed where the substance is associated with an identifiable disease or adverse effect, early detection can reduce harm, and workplace conditions make that harm likely. Health surveillance is not a replacement for exposure control. It is a backstop that helps identify whether control measures are failing or whether individuals are being affected. It may involve skin checks, respiratory questionnaires, lung-function testing, biological monitoring or review by occupational health depending on the substance and task. Typical triggers include asthmagens, sensitisers, substances causing dermatitis, work with certain carcinogens, exposure where symptoms have been reported, or situations where exposure is not adequately characterised. The choice should be based on COSHH assessment and competent occupational health advice. Records must be handled carefully.
Health surveillance results are sensitive personal data; employers usually need fitness or outcome information for management, not confidential clinical detail.
Do chemical safety requirements differ between GB and NI?
Source: chemical-safety--devolved
Use the work location and supply market to choose the correct regulator and statutory route. GB workplace exposure follows COSHH 2002 and HSE guidance; Northern Ireland follows COSHH (NI) 2003 and HSENI guidance. GB DSEAR 2002 and NI DSEAR 2003 may apply where dangerous substances create fire or explosion risk. GB CLP/UK REACH and NI EU CLP/EU REACH are separate supply systems. Competent specialists should check substance-specific duties and any cross-border supply scenario before ordering or use.
Which legal duties apply to chemical safety?
Source: chemical-safety--legal
Assess and control exposure under the applicable GB or NI COSHH instrument; consider fire, supply and emergency duties on their own terms. A general chemical inventory is not enough. The employer should identify each foreseeable task, route of exposure, by-product and potentially exposed person; prevent or adequately control exposure, maintain controls, brief workers and review after change. Relevant fire and explosion hazards require the local DSEAR route. A report under RIDDOR depends on the actual incident or diagnosis and jurisdiction; a spill is not automatically reportable. Waste, transport or major-accident rules require a separate scope assessment rather than blanket claims.
How could Crownway Fuels Ltd manage chemical safety?
Source: chemical-safety--business-example
Crownway Fuels Ltd could manage chemical safety by connecting procurement, storage, COSHH assessment, DSEAR, maintenance, worker training and assurance into one controlled system. For this example, Crownway Fuels Ltd operates a fuel storage and distribution site with fuel additives, cleaning chemicals, oils, laboratory reagents, tank residues and contractor maintenance work. Crownway begins with a controlled chemical register. No new chemical, additive, cleaner, degreaser, treatment product or laboratory reagent is purchased until the SDS is reviewed, the storage compatibility is checked, the COSHH assessment is drafted and the operational owner accepts the controls. The procurement system blocks unapproved chemicals so site teams cannot create unmanaged risk through convenience purchasing. The risk register separates health, fire/explosion, environmental and process-safety consequences.
For example, a solvent-based cleaner may sit in COSHH because of inhalation and skin effects, DSEAR because of flammable vapour, environmental controls because of drainage risk, and contractor control because it may be used during maintenance. Each risk has named barriers: substitution review, small containers, flammable cabinet, ventilation, no hot work nearby, product-specific glove compatibility and replacement limits, eye protection, spill kit, drain covers, waste route and supervisor sign-off. Implementation is evidence-based. Operators receive general chemical awareness and task briefings for fuels, additives and cleaning products. Maintenance contractors receive induction rules on bringing substances to site, SDS submission, decanting, labelling, spill response and permit interface. Stores inspections check segregation, labels, expiry dates, bund condition and incompatible storage.
HSSE completes second-line audits of COSHH assessments, LEV or ventilation where relevant, RPE fit testing, spill drills and learning from odour complaints, near misses or health surveillance trends. Continuous improvement is driven by data. If repeated inspections show unlabelled spray bottles, full drip trays, missing goggles or poor spill-kit replenishment, Crownway treats that as a system weakness rather than a worker problem. The management review then changes procurement controls, training, supervision, signage, storage design or contractor terms. For gloves, HSE selection guidance requires a choice matched to the substance and task. Record the manufacturer’s compatibility, permeation/degradation information and replacement decision; a glove material name alone is insufficient.
What should each role learn and demonstrate?
What should each role learn and demonstrate?
Source: chemical-safety--training
Learning must match the decisions people make, from recognising danger to checking that controls work. Briefings should tell people how to act, but attendance alone does not show competence. Assess the real decision or task, record who assessed it and revisit after a material change, failed control or incident. A local authorisation is task-specific; no universal external certificate is implied.
How does chemical safety support IOSH study and professional development?
Source: chemical-safety--study-development
Chemical safety supports IOSH study by linking hazardous-substance theory to practical COSHH assessment, control selection, monitoring and workplace evidence. For IOSH National General Certificate learners, the key is to explain the difference between hazard and risk, identify routes of entry, recognise forms of hazardous substance, describe COSHH assessment, apply the hierarchy of control and understand information, instruction, training and health surveillance. Scenario questions often test application rather than memory. A learner may be given a cleaning, spraying, welding, construction, laboratory or maintenance scenario and asked to identify what is wrong, what controls are missing, what training is needed or how the employer should improve monitoring.
For diploma-level learning, the topic expands into occupational hygiene, toxicology principles, WELs, exposure measurement, biological monitoring, hierarchy of controls, carcinogens, sensitisers, health surveillance, audit and management-system assurance.
How can a management system sustain effective decisions?
Source: chemical-safety--management-system
Give each hazard or support route an owner, a control, a check and a response to failure. Keep procurement, assessment, source controls, health surveillance and emergency decisions connected through named owners and review after change. An owner should sample actual work and corrective actions, not accept a policy or certificate as evidence that the controls work. The free GB regulator guide HSE Managing for health and safety (HSG65) explains a plan–do–check–act approach: assign controls and owners, involve workers, check work as done, and correct failures. For Northern Ireland, use HSENI risk assessment guidance for the local duty. A certificate alone does not demonstrate that a control works.
What are the warning signs that chemical safety is not being managed well?
Source: chemical-safety--warning-signs
Warning signs include outdated SDSs, generic COSHH assessments, unlabelled containers, uncontrolled odours or dust, poor storage, weak training and repeated symptoms or spills. Weak chemical safety usually becomes visible before a serious event. Workers complain about smells, skin irritation or headaches. Gloves are selected because they are cheap rather than compatible. Spray bottles are unlabelled. Dust is swept dry. Flammable liquids are kept beside ignition sources. Spill kits are empty. These are not housekeeping details; they are early signs of exposure, fire or reaction risk. The harm pathway should be made explicit. An unlabelled container can lead to the wrong chemical being used or mixed. Poor segregation can create gas, heat or fire if containers leak. Failed LEV can increase inhalation exposure.
No skin surveillance can allow dermatitis to become established. No contractor chemical review can introduce incompatible or more hazardous products onto site. Each sign should trigger action: stop or contain the task if needed, review the assessment, speak to workers, check the SDS, inspect controls, involve competent advice and close improvements with evidence.
Source tables and records 1
Compatibility in plain English
Table ID: chemical-compatibility-and-inadvertent-mixing-compatibility-in-plain-english
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Aspect
Storage compatibility
- What it means
Whether substances can be stored near each other.
- Why it matters
Prevents reaction if containers leak, break or spill.
Row 2
- Aspect
Use compatibility
- What it means
Whether substances can be used together or in the same process.
- Why it matters
Prevents gas, heat, fire, overpressure or product instability.
Row 3
- Aspect
Transfer compatibility
- What it means
Whether the right substance reaches the right destination by the right route.
- Why it matters
Prevents wrong-tank and wrong-line events.
Row 4
- Aspect
Waste compatibility
- What it means
Whether waste streams can be bulked or stored together.
- Why it matters
Prevents drum explosions, toxic release and waste-treatment incidents.
Row 5
- Aspect
Emergency compatibility
- What it means
Whether response actions such as washing, dilution or absorbents are suitable.
- Why it matters
Prevents responders worsening the reaction.
Read the complete comparison table
| Row | Aspect | What it means | Why it matters |
|---|---|---|---|
| 1 | Storage compatibility | Whether substances can be stored near each other. | Prevents reaction if containers leak, break or spill. |
| 2 | Use compatibility | Whether substances can be used together or in the same process. | Prevents gas, heat, fire, overpressure or product instability. |
| 3 | Transfer compatibility | Whether the right substance reaches the right destination by the right route. | Prevents wrong-tank and wrong-line events. |
| 4 | Waste compatibility | Whether waste streams can be bulked or stored together. | Prevents drum explosions, toxic release and waste-treatment incidents. |
| 5 | Emergency compatibility | Whether response actions such as washing, dilution or absorbents are suitable. | Prevents responders worsening the reaction. |
Common incompatibility outcomes
Table ID: chemical-compatibility-and-inadvertent-mixing-common-incompatibility-outcomes
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Incompatibility
Acid plus hypochlorite bleach
- Possible reaction
Chlorine gas release.
- Typical control
Segregate, label, train and never mix cleaning chemicals.
Row 2
- Incompatibility
Acid plus alkali
- Possible reaction
Heat generation, boiling, splashing and pressure.
- Typical control
Segregate and control neutralisation by competent people only.
Row 3
- Incompatibility
Oxidiser plus organic or flammable material
- Possible reaction
Fire, rapid reaction or explosion.
- Typical control
Separate oxidisers from fuels, solvents, oils and combustibles.
Row 4
- Incompatibility
Water-reactive substance plus water
- Possible reaction
Heat, gas, fire or violent reaction.
- Typical control
Keep dry and use suitable emergency response.
Row 5
- Incompatibility
Cyanide or sulphide plus acid
- Possible reaction
Highly toxic gas release.
- Typical control
Segregate and prevent acid contamination.
Row 6
- Incompatibility
Incompatible waste streams
- Possible reaction
Gas, heat, pressure, fire or drum rupture.
- Typical control
Approve waste streams and test compatibility before bulking.
Read the complete comparison table
| Row | Incompatibility | Possible reaction | Typical control |
|---|---|---|---|
| 1 | Acid plus hypochlorite bleach | Chlorine gas release. | Segregate, label, train and never mix cleaning chemicals. |
| 2 | Acid plus alkali | Heat generation, boiling, splashing and pressure. | Segregate and control neutralisation by competent people only. |
| 3 | Oxidiser plus organic or flammable material | Fire, rapid reaction or explosion. | Separate oxidisers from fuels, solvents, oils and combustibles. |
| 4 | Water-reactive substance plus water | Heat, gas, fire or violent reaction. | Keep dry and use suitable emergency response. |
| 5 | Cyanide or sulphide plus acid | Highly toxic gas release. | Segregate and prevent acid contamination. |
| 6 | Incompatible waste streams | Gas, heat, pressure, fire or drum rupture. | Approve waste streams and test compatibility before bulking. |
Common inadvertent mixing locations
Table ID: chemical-compatibility-and-inadvertent-mixing-common-inadvertent-mixing-locations
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Location or activity
Cleaning cupboards
- Failure mode
Bleach, acids, descalers or ammonia products stored or used together.
- Example consequence
Chlorine or irritating gas release.
Row 2
- Location or activity
Chemical stores
- Failure mode
Incompatible products stored above, beside or inside same containment.
- Example consequence
Reaction after leak or container damage.
Row 3
- Location or activity
Bulk unloading
- Failure mode
Wrong hose, fill point, tank or valve lineup.
- Example consequence
Toxic gas, overpressure or tank contamination.
Row 4
- Location or activity
Laboratories
- Failure mode
Waste bottles, shared benches or reagent confusion.
- Example consequence
Heat, gas or glass/container rupture.
Row 5
- Location or activity
Waste areas
- Failure mode
Unknown wastes bulked without compatibility check.
- Example consequence
Fire, explosion, drum failure or release.
Row 6
- Location or activity
Drains and sumps
- Failure mode
Separate chemicals meet in shared drainage.
- Example consequence
Gas generation, pollution or confined-space hazard.
Row 7
- Location or activity
Maintenance cleaning
- Failure mode
Cleaner reacts with residue inside equipment.
- Example consequence
Toxic release, heat or corrosion.
Read the complete comparison table
| Row | Location or activity | Failure mode | Example consequence |
|---|---|---|---|
| 1 | Cleaning cupboards | Bleach, acids, descalers or ammonia products stored or used together. | Chlorine or irritating gas release. |
| 2 | Chemical stores | Incompatible products stored above, beside or inside same containment. | Reaction after leak or container damage. |
| 3 | Bulk unloading | Wrong hose, fill point, tank or valve lineup. | Toxic gas, overpressure or tank contamination. |
| 4 | Laboratories | Waste bottles, shared benches or reagent confusion. | Heat, gas or glass/container rupture. |
| 5 | Waste areas | Unknown wastes bulked without compatibility check. | Fire, explosion, drum failure or release. |
| 6 | Drains and sumps | Separate chemicals meet in shared drainage. | Gas generation, pollution or confined-space hazard. |
| 7 | Maintenance cleaning | Cleaner reacts with residue inside equipment. | Toxic release, heat or corrosion. |
Ordinary and higher-risk focus
Table ID: chemical-compatibility-and-inadvertent-mixing-ordinary-and-higher-risk-focus
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Setting
General workplace
- Main concerns
Cleaning chemicals, decanting, labels, cupboards and small spills.
- Additional controls
Simple segregation, approved products and worker briefings.
Row 2
- Setting
Construction and maintenance
- Main concerns
Wet cement, fuels, residues, drains and contractor chemicals.
- Additional controls
COSHH review, RAMS, permits and drain protection.
Row 3
- Setting
Laboratory
- Main concerns
Reagents, waste bottles, shared benches and reactive chemicals.
- Additional controls
Compatibility matrix, waste labels and local rules.
Row 4
- Setting
Waste treatment
- Main concerns
Unknown composition, bulking, decomposition and incompatible wastes.
- Additional controls
Compatibility testing, acceptance controls and quarantine.
Row 5
- Setting
Process or COMAH site
- Main concerns
Bulk transfer, storage tanks, pipelines and major release consequences.
- Additional controls
Independent verification, interlocks, alarms, line ID and emergency planning.
Read the complete comparison table
| Row | Setting | Main concerns | Additional controls |
|---|---|---|---|
| 1 | General workplace | Cleaning chemicals, decanting, labels, cupboards and small spills. | Simple segregation, approved products and worker briefings. |
| 2 | Construction and maintenance | Wet cement, fuels, residues, drains and contractor chemicals. | COSHH review, RAMS, permits and drain protection. |
| 3 | Laboratory | Reagents, waste bottles, shared benches and reactive chemicals. | Compatibility matrix, waste labels and local rules. |
| 4 | Waste treatment | Unknown composition, bulking, decomposition and incompatible wastes. | Compatibility testing, acceptance controls and quarantine. |
| 5 | Process or COMAH site | Bulk transfer, storage tanks, pipelines and major release consequences. | Independent verification, interlocks, alarms, line ID and emergency planning. |
Compatibility assessment steps
Table ID: chemical-compatibility-and-inadvertent-mixing-compatibility-assessment-steps
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Step
Inventory
- What to assess
Products, raw materials, intermediates, wastes, residues and cleaners.
- Evidence
Chemical register and waste register.
Row 2
- Step
SDS review
- What to assess
Sections 7, 8, 10, 11 and 13.
- Evidence
SDS review record.
Row 3
- Step
Compatibility matrix
- What to assess
Which substances or classes must be separated.
- Evidence
Matrix or segregation chart.
Row 4
- Step
Physical layout
- What to assess
Stores, bunds, shelves, tanks, drains, transfer points and routes.
- Evidence
Marked plan and inspection.
Row 5
- Step
Credible scenarios
- What to assess
Wrong transfer, leak mixing, drain mixing, waste bulking and cleaning residues.
- Evidence
Risk assessment or HAZOP/what-if review.
Row 6
- Step
Barrier review
- What to assess
Labels, locks, couplings, interlocks, permits, procedures and supervision.
- Evidence
Barrier register and test records.
Read the complete comparison table
| Row | Step | What to assess | Evidence |
|---|---|---|---|
| 1 | Inventory | Products, raw materials, intermediates, wastes, residues and cleaners. | Chemical register and waste register. |
| 2 | SDS review | Sections 7, 8, 10, 11 and 13. | SDS review record. |
| 3 | Compatibility matrix | Which substances or classes must be separated. | Matrix or segregation chart. |
| 4 | Physical layout | Stores, bunds, shelves, tanks, drains, transfer points and routes. | Marked plan and inspection. |
| 5 | Credible scenarios | Wrong transfer, leak mixing, drain mixing, waste bulking and cleaning residues. | Risk assessment or HAZOP/what-if review. |
| 6 | Barrier review | Labels, locks, couplings, interlocks, permits, procedures and supervision. | Barrier register and test records. |
Source comparison
Table ID: chemical-compatibility-and-inadvertent-mixing-ericpd-controls-for-compatibility
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Column 1
Eliminate
- Column 2
Remove an unnecessary product or cleaning step so bleach and acid do not need to be used together in the task.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed.
- Column 4
If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls.
Row 2
- Column 1
Reduce, including substitution
- Column 2
Trial an effective less reactive cleaning product or method after reviewing its full hazard profile.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Process/technical owner validates the alternative, its compatibility and any new risks before adoption.
- Column 4
Reject the alternative if suitability is unproved or its new hazards are unresolved.
Row 3
- Column 1
Isolate
- Column 2
Store incompatible products separately in suitable containment and keep dedicated, clearly identified dispensing equipment.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work.
- Column 4
Hold or stop for unknown residue, unexpected heat or gas, shared decanting equipment or an unapproved product.
Row 4
- Column 1
Control: physical safeguards
- Column 2
Use compatible closed dispensing arrangements; prevent cross-connections, shared funnels and return of contaminated product.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Competent equipment/process owner checks exact products, compatibility, dedicated containers and the actual cleaning sequence.
- Column 4
Hold or stop for unknown residue, unexpected heat or gas, shared decanting equipment or an unapproved product.
Row 5
- Column 1
Control: work method and response
- Column 2
Follow the approved sequence and product instructions; verify the surface and container are suitable before a different chemical is introduced.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Supervisor confirms the limits, response, communication and restart authority with the people doing this activity.
- Column 4
Stop if the agreed method, communication, competent cover or task limits cannot be maintained.
Row 6
- Column 1
PPE
- Column 2
Use assessed chemical gloves and eye protection; PPE cannot make deliberate mixing of incompatible products acceptable.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence.
- Column 4
Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails.
Row 7
- Column 1
Discipline
- Column 2
Check labels and stock at handover; quarantine unknown or unlabelled products and investigate unexpected residues.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Release only after cleaning supervisor approves product identity and a compatible method. Retain the checks and unresolved restrictions at handover.
- Column 4
Keep the activity on hold while defects or required reinstatement evidence remain unresolved.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Eliminate | Remove an unnecessary product or cleaning step so bleach and acid do not need to be used together in the task.Basis: UKHSA sodium hypochlorite and incompatible mixing | Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed. | If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls. |
| 2 | Reduce, including substitution | Trial an effective less reactive cleaning product or method after reviewing its full hazard profile.Basis: UKHSA sodium hypochlorite and incompatible mixing | Process/technical owner validates the alternative, its compatibility and any new risks before adoption. | Reject the alternative if suitability is unproved or its new hazards are unresolved. |
| 3 | Isolate | Store incompatible products separately in suitable containment and keep dedicated, clearly identified dispensing equipment.Basis: UKHSA sodium hypochlorite and incompatible mixing | Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work. | Hold or stop for unknown residue, unexpected heat or gas, shared decanting equipment or an unapproved product. |
| 4 | Control: physical safeguards | Use compatible closed dispensing arrangements; prevent cross-connections, shared funnels and return of contaminated product.Basis: UKHSA sodium hypochlorite and incompatible mixing | Competent equipment/process owner checks exact products, compatibility, dedicated containers and the actual cleaning sequence. | Hold or stop for unknown residue, unexpected heat or gas, shared decanting equipment or an unapproved product. |
| 5 | Control: work method and response | Follow the approved sequence and product instructions; verify the surface and container are suitable before a different chemical is introduced.Basis: UKHSA sodium hypochlorite and incompatible mixing | Supervisor confirms the limits, response, communication and restart authority with the people doing this activity. | Stop if the agreed method, communication, competent cover or task limits cannot be maintained. |
| 6 | PPE | Use assessed chemical gloves and eye protection; PPE cannot make deliberate mixing of incompatible products acceptable.Basis: UKHSA sodium hypochlorite and incompatible mixing | Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence. | Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails. |
| 7 | Discipline | Check labels and stock at handover; quarantine unknown or unlabelled products and investigate unexpected residues.Basis: UKHSA sodium hypochlorite and incompatible mixing | Release only after cleaning supervisor approves product identity and a compatible method. Retain the checks and unresolved restrictions at handover. | Keep the activity on hold while defects or required reinstatement evidence remain unresolved. |
Source comparison
Table ID: chemical-compatibility-and-inadvertent-mixing-ericpd-controls-for-compatibility-eseap
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Column 1
Elimination
- Column 2
Remove an unnecessary product or cleaning step so bleach and acid do not need to be used together in the task.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed.
- Column 4
If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls.
Row 2
- Column 1
Substitution
- Column 2
Trial an effective less reactive cleaning product or method after reviewing its full hazard profile.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Process/technical owner validates the alternative, its compatibility and any new risks before adoption.
- Column 4
Reject the alternative if suitability is unproved or its new hazards are unresolved.
Row 3
- Column 1
Engineering controls
- Column 2
Store incompatible products separately in suitable containment and keep dedicated, clearly identified dispensing equipment.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work.
- Column 4
Hold or stop for unknown residue, unexpected heat or gas, shared decanting equipment or an unapproved product.
Row 4
- Column 1
Engineering controls
- Column 2
Use compatible closed dispensing arrangements; prevent cross-connections, shared funnels and return of contaminated product.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Competent equipment/process owner checks exact products, compatibility, dedicated containers and the actual cleaning sequence.
- Column 4
Hold or stop for unknown residue, unexpected heat or gas, shared decanting equipment or an unapproved product.
Row 5
- Column 1
Administrative controls
- Column 2
Follow the approved sequence and product instructions; verify the surface and container are suitable before a different chemical is introduced.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Supervisor confirms the limits, response, communication and restart authority with the people doing this activity.
- Column 4
Stop if the agreed method, communication, competent cover or task limits cannot be maintained.
Row 6
- Column 1
PPE
- Column 2
Use assessed chemical gloves and eye protection; PPE cannot make deliberate mixing of incompatible products acceptable.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence.
- Column 4
Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails.
Row 7
- Column 1
Administrative controls
- Column 2
Check labels and stock at handover; quarantine unknown or unlabelled products and investigate unexpected residues.Basis: UKHSA sodium hypochlorite and incompatible mixing
- Column 3
Release only after cleaning supervisor approves product identity and a compatible method. Retain the checks and unresolved restrictions at handover.
- Column 4
Keep the activity on hold while defects or required reinstatement evidence remain unresolved.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Elimination | Remove an unnecessary product or cleaning step so bleach and acid do not need to be used together in the task.Basis: UKHSA sodium hypochlorite and incompatible mixing | Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed. | If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls. |
| 2 | Substitution | Trial an effective less reactive cleaning product or method after reviewing its full hazard profile.Basis: UKHSA sodium hypochlorite and incompatible mixing | Process/technical owner validates the alternative, its compatibility and any new risks before adoption. | Reject the alternative if suitability is unproved or its new hazards are unresolved. |
| 3 | Engineering controls | Store incompatible products separately in suitable containment and keep dedicated, clearly identified dispensing equipment.Basis: UKHSA sodium hypochlorite and incompatible mixing | Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work. | Hold or stop for unknown residue, unexpected heat or gas, shared decanting equipment or an unapproved product. |
| 4 | Engineering controls | Use compatible closed dispensing arrangements; prevent cross-connections, shared funnels and return of contaminated product.Basis: UKHSA sodium hypochlorite and incompatible mixing | Competent equipment/process owner checks exact products, compatibility, dedicated containers and the actual cleaning sequence. | Hold or stop for unknown residue, unexpected heat or gas, shared decanting equipment or an unapproved product. |
| 5 | Administrative controls | Follow the approved sequence and product instructions; verify the surface and container are suitable before a different chemical is introduced.Basis: UKHSA sodium hypochlorite and incompatible mixing | Supervisor confirms the limits, response, communication and restart authority with the people doing this activity. | Stop if the agreed method, communication, competent cover or task limits cannot be maintained. |
| 6 | PPE | Use assessed chemical gloves and eye protection; PPE cannot make deliberate mixing of incompatible products acceptable.Basis: UKHSA sodium hypochlorite and incompatible mixing | Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence. | Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails. |
| 7 | Administrative controls | Check labels and stock at handover; quarantine unknown or unlabelled products and investigate unexpected residues.Basis: UKHSA sodium hypochlorite and incompatible mixing | Release only after cleaning supervisor approves product identity and a compatible method. Retain the checks and unresolved restrictions at handover. | Keep the activity on hold while defects or required reinstatement evidence remain unresolved. |
Source comparison
Table ID: chemical-compatibility-and-inadvertent-mixing-worked-control-hierarchy
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Column 1
Eliminate
- Column 2
Keep incompatible or unidentified wastes separate and use an accepted segregated disposal route rather than bulking them.Basis: HSE chemical waste treatment
- Column 3
Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed.
- Column 4
If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls.
Row 2
- Column 1
Reduce, including substitution
- Column 2
Where treatment is necessary, select a validated alternative process that avoids the hazardous mixing step.Basis: HSE chemical waste treatment
- Column 3
Process/technical owner validates the alternative, its compatibility and any new risks before adoption.
- Column 4
Reject the alternative if suitability is unproved or its new hazards are unresolved.
Row 3
- Column 1
Isolate
- Column 2
Segregate the drums and protect the bulking area from unrelated materials, drains and unauthorised access.Basis: HSE chemical waste treatment
- Column 3
Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work.
- Column 4
Hold or stop for unidentified material, uncertain compatibility, pressure, heat or unexpected gas.
Row 4
- Column 1
Control: physical safeguards
- Column 2
Use compatible containment, transfer equipment and engineered protection specified by the waste-compatibility assessment.Basis: HSE chemical waste treatment
- Column 3
Competent equipment/process owner checks waste identity, compatibility evidence, receiving container and disposal acceptance.
- Column 4
Hold or stop for unidentified material, uncertain compatibility, pressure, heat or unexpected gas.
Row 5
- Column 1
Control: work method and response
- Column 2
A competent waste specialist checks identity, acceptance criteria, reaction hazards and the authorised transfer sequence before release.Basis: HSE chemical waste treatment
- Column 3
Supervisor confirms the limits, response, communication and restart authority with the people doing this activity.
- Column 4
Stop if the agreed method, communication, competent cover or task limits cannot be maintained.
Row 6
- Column 1
PPE
- Column 2
Select chemical PPE and any RPE for the actual wastes and method; protective clothing does not justify a compatibility trial by mixing.Basis: HSE chemical waste treatment
- Column 3
Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence.
- Column 4
Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails.
Row 7
- Column 1
Discipline
- Column 2
Reconcile labels, analysis and collection documents; keep rejected drums on hold until a suitable disposal decision is recorded.Basis: HSE chemical waste treatment
- Column 3
Release only after competent waste owner approves the segregated or validated treatment route. Retain the checks and unresolved restrictions at handover.
- Column 4
Keep the activity on hold while defects or required reinstatement evidence remain unresolved.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Eliminate | Keep incompatible or unidentified wastes separate and use an accepted segregated disposal route rather than bulking them.Basis: HSE chemical waste treatment | Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed. | If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls. |
| 2 | Reduce, including substitution | Where treatment is necessary, select a validated alternative process that avoids the hazardous mixing step.Basis: HSE chemical waste treatment | Process/technical owner validates the alternative, its compatibility and any new risks before adoption. | Reject the alternative if suitability is unproved or its new hazards are unresolved. |
| 3 | Isolate | Segregate the drums and protect the bulking area from unrelated materials, drains and unauthorised access.Basis: HSE chemical waste treatment | Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work. | Hold or stop for unidentified material, uncertain compatibility, pressure, heat or unexpected gas. |
| 4 | Control: physical safeguards | Use compatible containment, transfer equipment and engineered protection specified by the waste-compatibility assessment.Basis: HSE chemical waste treatment | Competent equipment/process owner checks waste identity, compatibility evidence, receiving container and disposal acceptance. | Hold or stop for unidentified material, uncertain compatibility, pressure, heat or unexpected gas. |
| 5 | Control: work method and response | A competent waste specialist checks identity, acceptance criteria, reaction hazards and the authorised transfer sequence before release.Basis: HSE chemical waste treatment | Supervisor confirms the limits, response, communication and restart authority with the people doing this activity. | Stop if the agreed method, communication, competent cover or task limits cannot be maintained. |
| 6 | PPE | Select chemical PPE and any RPE for the actual wastes and method; protective clothing does not justify a compatibility trial by mixing.Basis: HSE chemical waste treatment | Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence. | Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails. |
| 7 | Discipline | Reconcile labels, analysis and collection documents; keep rejected drums on hold until a suitable disposal decision is recorded.Basis: HSE chemical waste treatment | Release only after competent waste owner approves the segregated or validated treatment route. Retain the checks and unresolved restrictions at handover. | Keep the activity on hold while defects or required reinstatement evidence remain unresolved. |
Source comparison
Table ID: chemical-compatibility-and-inadvertent-mixing-worked-control-hierarchy-eseap
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Column 1
Elimination
- Column 2
Keep incompatible or unidentified wastes separate and use an accepted segregated disposal route rather than bulking them.Basis: HSE chemical waste treatment
- Column 3
Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed.
- Column 4
If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls.
Row 2
- Column 1
Substitution
- Column 2
Where treatment is necessary, select a validated alternative process that avoids the hazardous mixing step.Basis: HSE chemical waste treatment
- Column 3
Process/technical owner validates the alternative, its compatibility and any new risks before adoption.
- Column 4
Reject the alternative if suitability is unproved or its new hazards are unresolved.
Row 3
- Column 1
Engineering controls
- Column 2
Segregate the drums and protect the bulking area from unrelated materials, drains and unauthorised access.Basis: HSE chemical waste treatment
- Column 3
Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work.
- Column 4
Hold or stop for unidentified material, uncertain compatibility, pressure, heat or unexpected gas.
Row 4
- Column 1
Engineering controls
- Column 2
Use compatible containment, transfer equipment and engineered protection specified by the waste-compatibility assessment.Basis: HSE chemical waste treatment
- Column 3
Competent equipment/process owner checks waste identity, compatibility evidence, receiving container and disposal acceptance.
- Column 4
Hold or stop for unidentified material, uncertain compatibility, pressure, heat or unexpected gas.
Row 5
- Column 1
Administrative controls
- Column 2
A competent waste specialist checks identity, acceptance criteria, reaction hazards and the authorised transfer sequence before release.Basis: HSE chemical waste treatment
- Column 3
Supervisor confirms the limits, response, communication and restart authority with the people doing this activity.
- Column 4
Stop if the agreed method, communication, competent cover or task limits cannot be maintained.
Row 6
- Column 1
PPE
- Column 2
Select chemical PPE and any RPE for the actual wastes and method; protective clothing does not justify a compatibility trial by mixing.Basis: HSE chemical waste treatment
- Column 3
Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence.
- Column 4
Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails.
Row 7
- Column 1
Administrative controls
- Column 2
Reconcile labels, analysis and collection documents; keep rejected drums on hold until a suitable disposal decision is recorded.Basis: HSE chemical waste treatment
- Column 3
Release only after competent waste owner approves the segregated or validated treatment route. Retain the checks and unresolved restrictions at handover.
- Column 4
Keep the activity on hold while defects or required reinstatement evidence remain unresolved.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Elimination | Keep incompatible or unidentified wastes separate and use an accepted segregated disposal route rather than bulking them.Basis: HSE chemical waste treatment | Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed. | If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls. |
| 2 | Substitution | Where treatment is necessary, select a validated alternative process that avoids the hazardous mixing step.Basis: HSE chemical waste treatment | Process/technical owner validates the alternative, its compatibility and any new risks before adoption. | Reject the alternative if suitability is unproved or its new hazards are unresolved. |
| 3 | Engineering controls | Segregate the drums and protect the bulking area from unrelated materials, drains and unauthorised access.Basis: HSE chemical waste treatment | Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work. | Hold or stop for unidentified material, uncertain compatibility, pressure, heat or unexpected gas. |
| 4 | Engineering controls | Use compatible containment, transfer equipment and engineered protection specified by the waste-compatibility assessment.Basis: HSE chemical waste treatment | Competent equipment/process owner checks waste identity, compatibility evidence, receiving container and disposal acceptance. | Hold or stop for unidentified material, uncertain compatibility, pressure, heat or unexpected gas. |
| 5 | Administrative controls | A competent waste specialist checks identity, acceptance criteria, reaction hazards and the authorised transfer sequence before release.Basis: HSE chemical waste treatment | Supervisor confirms the limits, response, communication and restart authority with the people doing this activity. | Stop if the agreed method, communication, competent cover or task limits cannot be maintained. |
| 6 | PPE | Select chemical PPE and any RPE for the actual wastes and method; protective clothing does not justify a compatibility trial by mixing.Basis: HSE chemical waste treatment | Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence. | Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails. |
| 7 | Administrative controls | Reconcile labels, analysis and collection documents; keep rejected drums on hold until a suitable disposal decision is recorded.Basis: HSE chemical waste treatment | Release only after competent waste owner approves the segregated or validated treatment route. Retain the checks and unresolved restrictions at handover. | Keep the activity on hold while defects or required reinstatement evidence remain unresolved. |
Transfer barriers and failure response
Table ID: chemical-compatibility-and-inadvertent-mixing-transfer-check
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Column-1
Chemical identity — buyer/receiving lead
- Column-2
Match product, SDS, order and tank inventory; record independent check.
- Column-3
Hold delivery if any identity conflicts.
Row 2
- Column-1
Connection — engineer/operator
- Column-2
Inspect dedicated fitting, unique label, locked unused lines and line map.
- Column-3
Do not connect if fitting or line is ambiguous.
Row 3
- Column-1
Transfer — operator and driver
- Column-2
Agree sequence, monitoring, shutoff and emergency signal before flow.
- Column-3
Stop flow and isolate safely after alarm, leak or unexpected change.
Row 4
- Column-1
Change — process safety lead
- Column-2
Review temporary hose, tank or supplier changes before use.
- Column-3
Do not restart after bypass until authorised correction is verified.
Read the complete comparison table
| Row | Column-1 | Column-2 | Column-3 |
|---|---|---|---|
| 1 | Chemical identity — buyer/receiving lead | Match product, SDS, order and tank inventory; record independent check. | Hold delivery if any identity conflicts. |
| 2 | Connection — engineer/operator | Inspect dedicated fitting, unique label, locked unused lines and line map. | Do not connect if fitting or line is ambiguous. |
| 3 | Transfer — operator and driver | Agree sequence, monitoring, shutoff and emergency signal before flow. | Stop flow and isolate safely after alarm, leak or unexpected change. |
| 4 | Change — process safety lead | Review temporary hose, tank or supplier changes before use. | Do not restart after bypass until authorised correction is verified. |
Segregation controls
Table ID: chemical-compatibility-and-inadvertent-mixing-segregation-controls
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Storage issue
Acids and alkalis
- Why it matters
Can react with heat and splashing.
- Good practice
Separate cabinets, trays or bays.
Row 2
- Storage issue
Oxidisers and flammables
- Why it matters
Can intensify fire or cause violent reaction.
- Good practice
Dedicated segregated storage.
Row 3
- Storage issue
Hypochlorite and acids
- Why it matters
Can release chlorine gas.
- Good practice
Never store or use together without controlled process design.
Row 4
- Storage issue
Waste chemicals
- Why it matters
Composition may be uncertain.
- Good practice
Label, characterise and segregate waste streams.
Row 5
- Storage issue
Shared bunds
- Why it matters
Leaks can mix in containment.
- Good practice
Use compatible bunding and separate containment.
Row 6
- Storage issue
Decanted containers
- Why it matters
Missing identity creates wrong use and wrong disposal.
- Good practice
Approved labelled containers only.
Read the complete comparison table
| Row | Storage issue | Why it matters | Good practice |
|---|---|---|---|
| 1 | Acids and alkalis | Can react with heat and splashing. | Separate cabinets, trays or bays. |
| 2 | Oxidisers and flammables | Can intensify fire or cause violent reaction. | Dedicated segregated storage. |
| 3 | Hypochlorite and acids | Can release chlorine gas. | Never store or use together without controlled process design. |
| 4 | Waste chemicals | Composition may be uncertain. | Label, characterise and segregate waste streams. |
| 5 | Shared bunds | Leaks can mix in containment. | Use compatible bunding and separate containment. |
| 6 | Decanted containers | Missing identity creates wrong use and wrong disposal. | Approved labelled containers only. |
Source tables and records 2
Waste and drain controls
Table ID: chemical-compatibility-and-inadvertent-mixing-waste-and-drain-controls
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Control
Waste-stream approval
- Purpose
Prevents incompatible waste from being bulked.
- Evidence
Waste acceptance or approval record.
Row 2
- Control
No unknown bulking rule
- Purpose
Prevents reaction from unidentified material.
- Evidence
Quarantine and characterisation procedure.
Row 3
- Control
Drain map
- Purpose
Shows where spills and discharges may travel.
- Evidence
Current site drainage plan.
Row 4
- Control
Drain protection
- Purpose
Stops incompatible or polluting material entering drainage.
- Evidence
Drain covers, valves and spill drills.
Row 5
- Control
Waste labels
- Purpose
Communicate contents and hazards.
- Evidence
Label inspection and waste register.
Row 6
- Control
Compatibility testing
- Purpose
Confirms bulking is safe where required.
- Evidence
Test record and acceptance criteria.
Read the complete comparison table
| Row | Control | Purpose | Evidence |
|---|---|---|---|
| 1 | Waste-stream approval | Prevents incompatible waste from being bulked. | Waste acceptance or approval record. |
| 2 | No unknown bulking rule | Prevents reaction from unidentified material. | Quarantine and characterisation procedure. |
| 3 | Drain map | Shows where spills and discharges may travel. | Current site drainage plan. |
| 4 | Drain protection | Stops incompatible or polluting material entering drainage. | Drain covers, valves and spill drills. |
| 5 | Waste labels | Communicate contents and hazards. | Label inspection and waste register. |
| 6 | Compatibility testing | Confirms bulking is safe where required. | Test record and acceptance criteria. |
Inadvertent-mixing response
Table ID: chemical-compatibility-and-inadvertent-mixing-response-check
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Column-1
Wrong connection before flow
- Column-2
Operator holds transfer; supervisor confirms identity and route.
- Column-3
Independent route recheck.
Row 2
- Column-1
Unexpected heat, gas or pressure
- Column-2
Stop remotely if safe, evacuate and call emergency services.
- Column-3
Specialist declares scene safe.
Row 3
- Column-1
Waste or drain reaction
- Column-2
Isolate people and drain route if safe; notify environmental responder.
- Column-3
Waste characterization and drain control corrected.
Read the complete comparison table
| Row | Column-1 | Column-2 | Column-3 |
|---|---|---|---|
| 1 | Wrong connection before flow | Operator holds transfer; supervisor confirms identity and route. | Independent route recheck. |
| 2 | Unexpected heat, gas or pressure | Stop remotely if safe, evacuate and call emergency services. | Specialist declares scene safe. |
| 3 | Waste or drain reaction | Isolate people and drain route if safe; notify environmental responder. | Waste characterization and drain control corrected. |
Barrier-led controls
Table ID: chemical-compatibility-and-inadvertent-mixing-barrier-led-controls
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Barrier type
Prevention
- Example
Dedicated fill points, unique couplings, segregation and approved transfer route.
- Assurance evidence
Inspection and proof-test records.
Row 2
- Barrier type
Detection
- Example
High-level alarms, abnormal pressure/temperature, gas detection or operator observation.
- Assurance evidence
Alarm test and response drill.
Row 3
- Barrier type
Control
- Example
Emergency shut-off, isolation valves, bunding and drain isolation.
- Assurance evidence
Functional test and maintenance.
Row 4
- Barrier type
Mitigation
- Example
Evacuation, ventilation, emergency response, spill containment and incident command.
- Assurance evidence
Drill and emergency-plan review.
Row 5
- Barrier type
Organisational
- Example
Competence, handover, permit, independent verification and management of change.
- Assurance evidence
Training, audit and MOC records.
Read the complete comparison table
| Row | Barrier type | Example | Assurance evidence |
|---|---|---|---|
| 1 | Prevention | Dedicated fill points, unique couplings, segregation and approved transfer route. | Inspection and proof-test records. |
| 2 | Detection | High-level alarms, abnormal pressure/temperature, gas detection or operator observation. | Alarm test and response drill. |
| 3 | Control | Emergency shut-off, isolation valves, bunding and drain isolation. | Functional test and maintenance. |
| 4 | Mitigation | Evacuation, ventilation, emergency response, spill containment and incident command. | Drill and emergency-plan review. |
| 5 | Organisational | Competence, handover, permit, independent verification and management of change. | Training, audit and MOC records. |
Compatibility duties by location
Table ID: chemical-compatibility-and-inadvertent-mixing-jurisdiction-map
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Column-1
Exposure
- Column-2
GB COSHH 2002 and HSE guidance.
- Column-3
NI COSHH 2003 and HSENI guidance.
Row 2
- Column-1
Fire and reaction
- Column-2
GB dangerous-substance/fire route checked by competent person.
- Column-3
NI dangerous-substance/fire route checked by competent person.
Row 3
- Column-1
Major accident
- Column-2
GB COMAH only if thresholds/establishment scope apply.
- Column-3
NI COMAH only if thresholds/establishment scope apply.
Read the complete comparison table
| Row | Column-1 | Column-2 | Column-3 |
|---|---|---|---|
| 1 | Exposure | GB COSHH 2002 and HSE guidance. | NI COSHH 2003 and HSENI guidance. |
| 2 | Fire and reaction | GB dangerous-substance/fire route checked by competent person. | NI dangerous-substance/fire route checked by competent person. |
| 3 | Major accident | GB COMAH only if thresholds/establishment scope apply. | NI COMAH only if thresholds/establishment scope apply. |
Crownway compatibility management
Table ID: chemical-compatibility-and-inadvertent-mixing-crownway-compatibility-management
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- System element
Chemical register
- Example control
Compatibility class, SDS section 10, storage, owner and approved use.
- Assurance method
Monthly review and change trigger.
Row 2
- System element
Transfer verification
- Example control
Right product, tank, hose, valve lineup and ullage confirmed.
- Assurance method
Operator checklist and supervisor sample.
Row 3
- System element
Storage segregation
- Example control
Acids, alkalis, oxidisers, flammables and wastes separated.
- Assurance method
Store inspection and action close-out.
Row 4
- System element
Drain control
- Example control
Drain map, isolation valves and spill protection.
- Assurance method
Spill drill and inspection.
Row 5
- System element
Waste approval
- Example control
No bulking without waste identity and compatibility approval.
- Assurance method
Waste acceptance record.
Row 6
- System element
Training
- Example control
Role-specific training for operators, stores, contractors and supervisors.
- Assurance method
Competence matrix and observed task.
Row 7
- System element
Learning
- Example control
Near misses and weak signals reviewed as barrier degradation.
- Assurance method
Management review and verified improvements.
Read the complete comparison table
| Row | System element | Example control | Assurance method |
|---|---|---|---|
| 1 | Chemical register | Compatibility class, SDS section 10, storage, owner and approved use. | Monthly review and change trigger. |
| 2 | Transfer verification | Right product, tank, hose, valve lineup and ullage confirmed. | Operator checklist and supervisor sample. |
| 3 | Storage segregation | Acids, alkalis, oxidisers, flammables and wastes separated. | Store inspection and action close-out. |
| 4 | Drain control | Drain map, isolation valves and spill protection. | Spill drill and inspection. |
| 5 | Waste approval | No bulking without waste identity and compatibility approval. | Waste acceptance record. |
| 6 | Training | Role-specific training for operators, stores, contractors and supervisors. | Competence matrix and observed task. |
| 7 | Learning | Near misses and weak signals reviewed as barrier degradation. | Management review and verified improvements. |
Role-level learning and competence evidence
Table ID: chemical-compatibility-and-inadvertent-mixing-competence-decisions
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Column-1
Buyer/stores: compatibility and identity.
- Column-2
Competent chemist checks a proposed new product against storage, waste and transfer scenarios.
- Column-3
Approval and compatibility record; repeat after product change.
Row 2
- Column-1
Operator/driver: transfer route.
- Column-2
Supervisor observes independent tank/line checks and a stop decision for a wrong label.
- Column-3
Authorisation and observation; repeat after near miss.
Row 3
- Column-1
Engineer: fixed barriers.
- Column-2
Process engineer tests couplings, locks, interlocks and shutoff on the actual line.
- Column-3
Inspection/proof-test record; repeat after maintenance.
Row 4
- Column-1
Emergency lead: release response.
- Column-2
Drill toxic-gas cue, evacuation, 999 handover and safe remote isolation.
- Column-3
Drill result and action closure; repeat after layout change.
Read the complete comparison table
| Row | Column-1 | Column-2 | Column-3 |
|---|---|---|---|
| 1 | Buyer/stores: compatibility and identity. | Competent chemist checks a proposed new product against storage, waste and transfer scenarios. | Approval and compatibility record; repeat after product change. |
| 2 | Operator/driver: transfer route. | Supervisor observes independent tank/line checks and a stop decision for a wrong label. | Authorisation and observation; repeat after near miss. |
| 3 | Engineer: fixed barriers. | Process engineer tests couplings, locks, interlocks and shutoff on the actual line. | Inspection/proof-test record; repeat after maintenance. |
| 4 | Emergency lead: release response. | Drill toxic-gas cue, evacuation, 999 handover and safe remote isolation. | Drill result and action closure; repeat after layout change. |
Study application
Table ID: chemical-compatibility-and-inadvertent-mixing-study-application
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Study area
Compatibility basics
- What to know
Which substances can react and what consequences may occur.
- Scenario application
Explain why a storage or transfer arrangement is unsafe.
Row 2
- Study area
SDS use
- What to know
Section 10 stability and reactivity, plus sections 7 and 13.
- Scenario application
Use SDS information to set controls.
Row 3
- Study area
Transfer verification
- What to know
Right product, tank, route, connection, capacity and valve lineup.
- Scenario application
Identify missing checks and stronger barriers.
Row 4
- Study area
Human factors
- What to know
Similar labels, similar couplings, assumptions and shift handover.
- Scenario application
Explain why error was predictable.
Row 5
- Study area
Major accident barriers
- What to know
Prevention, detection, control and mitigation.
- Scenario application
Link barriers to toxic release, fire, explosion and overpressure.
Row 6
- Study area
Emergency response
- What to know
Evacuation, isolation, specialist response and drain protection.
- Scenario application
Avoid improvised neutralisation or clean-up.
Read the complete comparison table
| Row | Study area | What to know | Scenario application |
|---|---|---|---|
| 1 | Compatibility basics | Which substances can react and what consequences may occur. | Explain why a storage or transfer arrangement is unsafe. |
| 2 | SDS use | Section 10 stability and reactivity, plus sections 7 and 13. | Use SDS information to set controls. |
| 3 | Transfer verification | Right product, tank, route, connection, capacity and valve lineup. | Identify missing checks and stronger barriers. |
| 4 | Human factors | Similar labels, similar couplings, assumptions and shift handover. | Explain why error was predictable. |
| 5 | Major accident barriers | Prevention, detection, control and mitigation. | Link barriers to toxic release, fire, explosion and overpressure. |
| 6 | Emergency response | Evacuation, isolation, specialist response and drain protection. | Avoid improvised neutralisation or clean-up. |
Incident learning
Table ID: chemical-compatibility-and-inadvertent-mixing-incident-learning
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Incident
US CSB MGPI investigation
- What failed
Sulphuric acid was inadvertently unloaded into a sodium hypochlorite tank, producing a chlorine-containing release.
- Learning for compatibility control
Design transfer systems so wrong connections are difficult, verify product and destination, define responsibilities and plan emergency response.
Row 2
- Incident
HSE - Chemical waste treatment
- What failed
HSE describes incidents caused by unintentional or inadequately planned mixing of incompatible chemical waste, including fires, explosions, releases and environmental effects.
- Learning for compatibility control
Characterise waste streams and test compatibility before bulking or treatment.
Read the complete comparison table
| Row | Incident | What failed | Learning for compatibility control |
|---|---|---|---|
| 1 | US CSB MGPI investigation | Sulphuric acid was inadvertently unloaded into a sodium hypochlorite tank, producing a chlorine-containing release. | Design transfer systems so wrong connections are difficult, verify product and destination, define responsibilities and plan emergency response. |
| 2 | HSE - Chemical waste treatment | HSE describes incidents caused by unintentional or inadequately planned mixing of incompatible chemical waste, including fires, explosions, releases and environmental effects. | Characterise waste streams and test compatibility before bulking or treatment. |
Warning signs and likely consequence
Table ID: chemical-compatibility-and-inadvertent-mixing-warning-signs-and-likely-consequence
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Warning sign
Unlabelled containers
- How harm can develop
Wrong use, wrong disposal or wrong first response.
- Action
Remove from use and identify/dispose safely.
Row 2
- Warning sign
Shared hoses or funnels
- How harm can develop
Cross-contamination between incompatible substances.
- Action
Use dedicated equipment or clean/verify controls.
Row 3
- Warning sign
Similar fill points
- How harm can develop
Wrong-tank transfer.
- Action
Differentiate physically and verify independently.
Row 4
- Warning sign
Unknown waste drums
- How harm can develop
Incompatible bulking, gas or pressure.
- Action
Quarantine and characterise before moving.
Row 5
- Warning sign
Incompatible shared bund
- How harm can develop
Leaking containers mix in containment.
- Action
Separate containment.
Row 6
- Warning sign
No drain map
- How harm can develop
Releases travel to unknown locations.
- Action
Map, label and protect drains.
Row 7
- Warning sign
Workers neutralise spills informally
- How harm can develop
Reaction worsens or responders exposed.
- Action
Stop practice and train emergency route.
Read the complete comparison table
| Row | Warning sign | How harm can develop | Action |
|---|---|---|---|
| 1 | Unlabelled containers | Wrong use, wrong disposal or wrong first response. | Remove from use and identify/dispose safely. |
| 2 | Shared hoses or funnels | Cross-contamination between incompatible substances. | Use dedicated equipment or clean/verify controls. |
| 3 | Similar fill points | Wrong-tank transfer. | Differentiate physically and verify independently. |
| 4 | Unknown waste drums | Incompatible bulking, gas or pressure. | Quarantine and characterise before moving. |
| 5 | Incompatible shared bund | Leaking containers mix in containment. | Separate containment. |
| 6 | No drain map | Releases travel to unknown locations. | Map, label and protect drains. |
| 7 | Workers neutralise spills informally | Reaction worsens or responders exposed. | Stop practice and train emergency route. |
Official links and their use
Table ID: chemical-compatibility-and-inadvertent-mixing-official-links
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Column-1
HSE chemical waste treatment
- Column-2
Great Britain regulator
- Column-3
Incompatible waste and compatibility testing
Row 2
- Column-1
HSE using chemicals at work
- Column-2
Great Britain regulator
- Column-3
Chemical handling
Row 3
- Column-1
HSE COSHH assessment
- Column-2
Great Britain regulator
- Column-3
Exposure assessment and control
Row 4
- Column-1
HSE chemical safety data sheets
- Column-2
Great Britain regulator
- Column-3
Stability, reaction and emergency information
Row 5
- Column-1
HSE fire and explosion
- Column-2
Great Britain regulator
- Column-3
Fire/explosion controls
Row 6
- Column-1
HSE COMAH
- Column-2
Great Britain major-hazard regulator
- Column-3
COMAH only when establishment is in scope
Row 7
- Column-1
HSENI COSHH
- Column-2
Northern Ireland regulator
- Column-3
NI exposure route
Row 8
- Column-1
HSENI COMAH
- Column-2
Northern Ireland major-hazard regulator
- Column-3
NI COMAH scope check
Row 9
- Column-1
HSENI SDS section headings
- Column-2
Northern Ireland regulator; headings only
- Column-3
Section 10 stability and reactivity
Row 10
- Column-1
US CSB MGPI investigation
- Column-2
United States investigation; transferable lesson, not UK law
- Column-3
Acid into hypochlorite tank and transfer safeguards
Row 11
- Column-1
HSE Managing for health and safety (HSG65)
- Column-2
HSE management guidance for Great Britain; check current edition
- Column-3
Plan–do–check–act management guidance
Row 12
- Column-1
HSE five-level hierarchy
- Column-2
Great Britain | HSE
- Column-3
Elimination, substitution, engineering, administrative controls and PPE
Row 13
- Column-1
HSE chemical warehousing (HSG71)
- Column-2
Great Britain | HSE
- Column-3
2009 fourth edition: chemical incompatibility examples, paragraph120; check current law separately
Read the complete comparison table
| Row | Column-1 | Column-2 | Column-3 |
|---|---|---|---|
| 1 | HSE chemical waste treatment | Great Britain regulator | Incompatible waste and compatibility testing |
| 2 | HSE using chemicals at work | Great Britain regulator | Chemical handling |
| 3 | HSE COSHH assessment | Great Britain regulator | Exposure assessment and control |
| 4 | HSE chemical safety data sheets | Great Britain regulator | Stability, reaction and emergency information |
| 5 | HSE fire and explosion | Great Britain regulator | Fire/explosion controls |
| 6 | HSE COMAH | Great Britain major-hazard regulator | COMAH only when establishment is in scope |
| 7 | HSENI COSHH | Northern Ireland regulator | NI exposure route |
| 8 | HSENI COMAH | Northern Ireland major-hazard regulator | NI COMAH scope check |
| 9 | HSENI SDS section headings | Northern Ireland regulator; headings only | Section 10 stability and reactivity |
| 10 | US CSB MGPI investigation | United States investigation; transferable lesson, not UK law | Acid into hypochlorite tank and transfer safeguards |
| 11 | HSE Managing for health and safety (HSG65) | HSE management guidance for Great Britain; check current edition | Plan–do–check–act management guidance |
| 12 | HSE five-level hierarchy | Great Britain | HSE | Elimination, substitution, engineering, administrative controls and PPE |
| 13 | HSE chemical warehousing (HSG71) | Great Britain | HSE | 2009 fourth edition: chemical incompatibility examples, paragraph120; check current law separately |
Acronyms and plain-English meanings
Table ID: chemical-compatibility-and-inadvertent-mixing-acronyms-and-plain-english-meanings
Source: https://www.sharehub.ltd/knowledge-hub/chemical-compatibility-and-inadvertent-mixing.html
Row 1
- Term
COSHH
- Meaning
Control of Substances Hazardous to Health
- Plain english use
Controls health exposure from hazardous substances.
Row 2
- Term
DSEAR
- Meaning
Dangerous Substances and Explosive Atmospheres Regulations
- Plain english use
Controls fire and explosion from dangerous substances.
Row 3
- Term
SDS
- Meaning
Safety Data Sheet
- Plain english use
Supplier information used to assess hazards, storage and incompatibilities.
Row 4
- Term
MOC
- Meaning
Management of Change
- Plain english use
Controls changes to chemicals, equipment, procedures or layout.
Row 5
- Term
HAZOP
- Meaning
Hazard and Operability Study
- Plain english use
Structured process hazard review method.
Row 6
- Term
COMAH
- Meaning
Control of Major Accident Hazards
- Plain english use
Regime for qualifying major accident hazard establishments.
Row 7
- Term
IBC
- Meaning
Intermediate Bulk Container
- Plain english use
Common chemical or waste container requiring compatibility and labelling control.
Row 8
- Term
LEV
- Meaning
Local Exhaust Ventilation
- Plain english use
Engineering control for vapour, fume, mist or dust exposure.
Row 9
- Term
RPE
- Meaning
Respiratory Protective Equipment
- Plain english use
Respirators or masks used where airborne exposure remains.
Row 10
- Term
ERICPD
- Meaning
Eliminate, Reduce, Isolate, Control, Personal protective equipment, Discipline
- Plain english use
Hierarchy for selecting risk controls.
Read the complete comparison table
| Row | Term | Meaning | Plain english use |
|---|---|---|---|
| 1 | COSHH | Control of Substances Hazardous to Health | Controls health exposure from hazardous substances. |
| 2 | DSEAR | Dangerous Substances and Explosive Atmospheres Regulations | Controls fire and explosion from dangerous substances. |
| 3 | SDS | Safety Data Sheet | Supplier information used to assess hazards, storage and incompatibilities. |
| 4 | MOC | Management of Change | Controls changes to chemicals, equipment, procedures or layout. |
| 5 | HAZOP | Hazard and Operability Study | Structured process hazard review method. |
| 6 | COMAH | Control of Major Accident Hazards | Regime for qualifying major accident hazard establishments. |
| 7 | IBC | Intermediate Bulk Container | Common chemical or waste container requiring compatibility and labelling control. |
| 8 | LEV | Local Exhaust Ventilation | Engineering control for vapour, fume, mist or dust exposure. |
| 9 | RPE | Respiratory Protective Equipment | Respirators or masks used where airborne exposure remains. |
| 10 | ERICPD | Eliminate, Reduce, Isolate, Control, Personal protective equipment, Discipline | Hierarchy for selecting risk controls. |
Chemical safety lifecycle
Table ID: chemical-safety-chemical-safety-lifecycle
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Lifecycle stage
Selection
- What good management looks like
Choose a safer substance or process where reasonably practicable.
- Evidence to keep
Substitution review and approval record.
Row 2
- Lifecycle stage
Purchase
- What good management looks like
Check SDS, classification, storage needs, WELs and restrictions before ordering.
- Evidence to keep
Approved chemical register entry.
Row 3
- Lifecycle stage
Receipt and labelling
- What good management looks like
Confirm container identity, label condition and storage location.
- Evidence to keep
Goods-in check and SDS access.
Row 4
- Lifecycle stage
Use
- What good management looks like
Apply COSHH controls for the actual task and exposure route.
- Evidence to keep
COSHH assessment, training and supervision record.
Row 5
- Lifecycle stage
Maintenance and cleaning
- What good management looks like
Control hidden residues, contaminated plant, line-breaking and cleaning exposure.
- Evidence to keep
Permit, isolation, decontamination and inspection records.
Row 6
- Lifecycle stage
Disposal
- What good management looks like
Dispose of chemicals, containers and contaminated waste safely.
- Evidence to keep
Waste transfer or disposal evidence where required.
Read the complete comparison table
| Row | Lifecycle stage | What good management looks like | Evidence to keep |
|---|---|---|---|
| 1 | Selection | Choose a safer substance or process where reasonably practicable. | Substitution review and approval record. |
| 2 | Purchase | Check SDS, classification, storage needs, WELs and restrictions before ordering. | Approved chemical register entry. |
| 3 | Receipt and labelling | Confirm container identity, label condition and storage location. | Goods-in check and SDS access. |
| 4 | Use | Apply COSHH controls for the actual task and exposure route. | COSHH assessment, training and supervision record. |
| 5 | Maintenance and cleaning | Control hidden residues, contaminated plant, line-breaking and cleaning exposure. | Permit, isolation, decontamination and inspection records. |
| 6 | Disposal | Dispose of chemicals, containers and contaminated waste safely. | Waste transfer or disposal evidence where required. |
Chemical forms and typical concerns
Table ID: chemical-safety-chemical-forms-and-typical-concerns
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Form
Gas
- Examples
Chlorine, ammonia, carbon dioxide, nitrogen.
- Main concern
Inhalation, asphyxiation, toxicity, pressure or release.
Row 2
- Form
Vapour
- Examples
Solvent vapour from paints, thinners or fuels.
- Main concern
Inhalation, flammability and nervous-system effects.
Row 3
- Form
Fume
- Examples
Welding fume, thermal decomposition products.
- Main concern
Fine particles and metal oxide exposure.
Row 4
- Form
Mist or aerosol
- Examples
Spraying, machining fluids, disinfectant fogging.
- Main concern
Inhalation and skin or eye deposition.
Row 5
- Form
Dust or powder
- Examples
Silica, flour, cement, powders and pigments.
- Main concern
Respirable dust, skin contact and combustible dust where relevant.
Row 6
- Form
Liquid or paste
- Examples
Acids, alkalis, resins, adhesives and coatings.
- Main concern
Skin absorption, burns, dermatitis, splash and fire risk.
Row 7
- Form
Solid article or residue
- Examples
Contaminated filters, rags, deposits or absorbents.
- Main concern
Secondary exposure during cleaning, storage or disposal.
Read the complete comparison table
| Row | Form | Examples | Main concern |
|---|---|---|---|
| 1 | Gas | Chlorine, ammonia, carbon dioxide, nitrogen. | Inhalation, asphyxiation, toxicity, pressure or release. |
| 2 | Vapour | Solvent vapour from paints, thinners or fuels. | Inhalation, flammability and nervous-system effects. |
| 3 | Fume | Welding fume, thermal decomposition products. | Fine particles and metal oxide exposure. |
| 4 | Mist or aerosol | Spraying, machining fluids, disinfectant fogging. | Inhalation and skin or eye deposition. |
| 5 | Dust or powder | Silica, flour, cement, powders and pigments. | Respirable dust, skin contact and combustible dust where relevant. |
| 6 | Liquid or paste | Acids, alkalis, resins, adhesives and coatings. | Skin absorption, burns, dermatitis, splash and fire risk. |
| 7 | Solid article or residue | Contaminated filters, rags, deposits or absorbents. | Secondary exposure during cleaning, storage or disposal. |
Routes of entry and exposure
Table ID: chemical-safety-routes-of-entry-and-exposure
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Route
Inhalation
- How exposure occurs
Breathing dust, mist, fume, gas or vapour.
- Typical controls
Elimination, enclosure, LEV, ventilation, process control and RPE.
Row 2
- Route
Skin contact
- How exposure occurs
Liquid, dust, paste or contaminated PPE touches skin.
- Typical controls
Substitution, closed handling, gloves, clothing, welfare and skin checks.
Row 3
- Route
Skin absorption
- How exposure occurs
Substance passes through skin into the body.
- Typical controls
Chemical-resistant PPE, hygiene and exposure-time control.
Row 4
- Route
Eye contact
- How exposure occurs
Splash, dust or aerosol enters the eye.
- Typical controls
Closed transfer, splash guards, goggles, face shields and eyewash.
Row 5
- Route
Ingestion
- How exposure occurs
Contaminated hands, food, drink or cigarettes transfer substance to mouth.
- Typical controls
Hygiene, clean welfare, no eating in contaminated areas and supervision.
Row 6
- Route
Injection
- How exposure occurs
High-pressure fluid or contaminated sharp punctures skin.
- Typical controls
Guarding, depressurisation, sharps controls and emergency escalation.
Read the complete comparison table
| Row | Route | How exposure occurs | Typical controls |
|---|---|---|---|
| 1 | Inhalation | Breathing dust, mist, fume, gas or vapour. | Elimination, enclosure, LEV, ventilation, process control and RPE. |
| 2 | Skin contact | Liquid, dust, paste or contaminated PPE touches skin. | Substitution, closed handling, gloves, clothing, welfare and skin checks. |
| 3 | Skin absorption | Substance passes through skin into the body. | Chemical-resistant PPE, hygiene and exposure-time control. |
| 4 | Eye contact | Splash, dust or aerosol enters the eye. | Closed transfer, splash guards, goggles, face shields and eyewash. |
| 5 | Ingestion | Contaminated hands, food, drink or cigarettes transfer substance to mouth. | Hygiene, clean welfare, no eating in contaminated areas and supervision. |
| 6 | Injection | High-pressure fluid or contaminated sharp punctures skin. | Guarding, depressurisation, sharps controls and emergency escalation. |
Health effects to consider
Table ID: chemical-safety-health-effects-to-consider
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Effect type
Irritation
- Examples
Eye, throat, airway or skin irritation.
- What it means for management
Check exposure route, concentration, contact time and controls.
Row 2
- Effect type
Corrosion and burns
- Examples
Acids, alkalis and corrosive cleaners.
- What it means for management
Need splash prevention, emergency washing and trained response.
Row 3
- Effect type
Sensitisation
- Examples
Isocyanates, epoxy resins, some dusts and biological agents.
- What it means for management
Exposure should be prevented or tightly controlled with surveillance.
Row 4
- Effect type
Toxicity
- Examples
Solvents, gases, metals and pesticides.
- What it means for management
Need exposure limits, task control, monitoring and medical arrangements where required.
Row 5
- Effect type
Carcinogenicity
- Examples
Certain dusts, fumes, solvents and process substances.
- What it means for management
Exposure must be reduced to as low as reasonably practicable where relevant.
Row 6
- Effect type
Reproductive effects
- Examples
Some solvents, metals and substances toxic to reproduction.
- What it means for management
Need specific risk assessment, substitution and worker information.
Row 7
- Effect type
Asphyxiation
- Examples
Nitrogen, carbon dioxide or oxygen-displacing gases.
- What it means for management
Need atmosphere control, ventilation, detection and confined-space controls.
Read the complete comparison table
| Row | Effect type | Examples | What it means for management |
|---|---|---|---|
| 1 | Irritation | Eye, throat, airway or skin irritation. | Check exposure route, concentration, contact time and controls. |
| 2 | Corrosion and burns | Acids, alkalis and corrosive cleaners. | Need splash prevention, emergency washing and trained response. |
| 3 | Sensitisation | Isocyanates, epoxy resins, some dusts and biological agents. | Exposure should be prevented or tightly controlled with surveillance. |
| 4 | Toxicity | Solvents, gases, metals and pesticides. | Need exposure limits, task control, monitoring and medical arrangements where required. |
| 5 | Carcinogenicity | Certain dusts, fumes, solvents and process substances. | Exposure must be reduced to as low as reasonably practicable where relevant. |
| 6 | Reproductive effects | Some solvents, metals and substances toxic to reproduction. | Need specific risk assessment, substitution and worker information. |
| 7 | Asphyxiation | Nitrogen, carbon dioxide or oxygen-displacing gases. | Need atmosphere control, ventilation, detection and confined-space controls. |
Chemical risk assessment steps
Table ID: chemical-safety-chemical-risk-assessment-steps
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Step
Create the inventory
- What to do
List substances purchased, stored, used, generated and disposed of.
- Common weak point
Only listing purchased products and missing process-generated hazards.
Row 2
- Step
Read SDS and labels
- What to do
Identify classification, exposure limits, incompatibilities and emergency measures.
- Common weak point
Using out-of-date SDS or not checking sections 7, 8 and 10.
Row 3
- Step
Define the task
- What to do
Describe how the substance is actually used.
- Common weak point
Generic assessment that ignores spraying, heating, mixing or confined areas.
Row 4
- Step
Identify exposure routes
- What to do
Consider inhalation, skin, eyes, ingestion and injection.
- Common weak point
Assuming gloves or masks solve all routes.
Row 5
- Step
Identify people exposed
- What to do
Include workers, cleaners, maintenance, contractors, visitors and nearby workgroups.
- Common weak point
Missing secondary exposure.
Row 6
- Step
Choose controls
- What to do
Apply hierarchy and COSHH principles of good control practice.
- Common weak point
Jumping straight to PPE.
Row 7
- Step
Record and brief
- What to do
Make controls clear enough for the work team to use.
- Common weak point
Assessment is filed but not translated into work instructions.
Row 8
- Step
Review
- What to do
Review after changes, symptoms, monitoring results, incidents or new information.
- Common weak point
No trigger-based review process.
Read the complete comparison table
| Row | Step | What to do | Common weak point |
|---|---|---|---|
| 1 | Create the inventory | List substances purchased, stored, used, generated and disposed of. | Only listing purchased products and missing process-generated hazards. |
| 2 | Read SDS and labels | Identify classification, exposure limits, incompatibilities and emergency measures. | Using out-of-date SDS or not checking sections 7, 8 and 10. |
| 3 | Define the task | Describe how the substance is actually used. | Generic assessment that ignores spraying, heating, mixing or confined areas. |
| 4 | Identify exposure routes | Consider inhalation, skin, eyes, ingestion and injection. | Assuming gloves or masks solve all routes. |
| 5 | Identify people exposed | Include workers, cleaners, maintenance, contractors, visitors and nearby workgroups. | Missing secondary exposure. |
| 6 | Choose controls | Apply hierarchy and COSHH principles of good control practice. | Jumping straight to PPE. |
| 7 | Record and brief | Make controls clear enough for the work team to use. | Assessment is filed but not translated into work instructions. |
| 8 | Review | Review after changes, symptoms, monitoring results, incidents or new information. | No trigger-based review process. |
Source tables and records 3
Source comparison
Table ID: chemical-safety-ericpd-hierarchy-for-chemical-safety
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Column 1
Eliminate
- Column 2
Buy components ready for assembly or remove an unnecessary cleaning stage where cleanliness requirements permit.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed.
- Column 4
If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls.
Row 2
- Column 1
Reduce, including substitution
- Column 2
Trial a suitable aqueous or other lower-hazard cleaning process; validate component finish and any new corrosion or skin risk.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Process/technical owner validates the alternative, its compatibility and any new risks before adoption.
- Column 4
Reject the alternative if suitability is unproved or its new hazards are unresolved.
Row 3
- Column 1
Isolate
- Column 2
Use a designated cleaning station away from ignition sources and unrelated work; segregate contaminated items and waste.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work.
- Column 4
Hold or stop for unknown solvent, failed extraction, uncontrolled vapour or incompatible waste.
Row 4
- Column 1
Control: physical safeguards
- Column 2
Use compatible enclosed cleaning equipment and effective local extraction where required; minimise open liquid and splash paths.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Competent equipment/process owner checks product identity, enclosure, extraction, waste containment and cleaning quality.
- Column 4
Hold or stop for unknown solvent, failed extraction, uncontrolled vapour or incompatible waste.
Row 5
- Column 1
Control: work method and response
- Column 2
Identify the product and contamination, control decanting and waste, and prohibit unassessed mixing or heating.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Supervisor confirms the limits, response, communication and restart authority with the people doing this activity.
- Column 4
Stop if the agreed method, communication, competent cover or task limits cannot be maintained.
Row 6
- Column 1
PPE
- Column 2
Select gloves, eye protection and any RPE for the actual formulation; a particulate mask does not protect against solvent vapour.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence.
- Column 4
Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails.
Row 7
- Column 1
Discipline
- Column 2
Maintain seals and extraction, check cleaning quality and investigate exposure or fire-control defects before restarting.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Release only after maintenance owner accepts the cleaning trial and verified controls. Retain the checks and unresolved restrictions at handover.
- Column 4
Keep the activity on hold while defects or required reinstatement evidence remain unresolved.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Eliminate | Buy components ready for assembly or remove an unnecessary cleaning stage where cleanliness requirements permit.Basis: Official task guidance: www.hse.gov.uk | Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed. | If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls. |
| 2 | Reduce, including substitution | Trial a suitable aqueous or other lower-hazard cleaning process; validate component finish and any new corrosion or skin risk.Basis: Official task guidance: www.hse.gov.uk | Process/technical owner validates the alternative, its compatibility and any new risks before adoption. | Reject the alternative if suitability is unproved or its new hazards are unresolved. |
| 3 | Isolate | Use a designated cleaning station away from ignition sources and unrelated work; segregate contaminated items and waste.Basis: Official task guidance: www.hse.gov.uk | Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work. | Hold or stop for unknown solvent, failed extraction, uncontrolled vapour or incompatible waste. |
| 4 | Control: physical safeguards | Use compatible enclosed cleaning equipment and effective local extraction where required; minimise open liquid and splash paths.Basis: Official task guidance: www.hse.gov.uk | Competent equipment/process owner checks product identity, enclosure, extraction, waste containment and cleaning quality. | Hold or stop for unknown solvent, failed extraction, uncontrolled vapour or incompatible waste. |
| 5 | Control: work method and response | Identify the product and contamination, control decanting and waste, and prohibit unassessed mixing or heating.Basis: Official task guidance: www.hse.gov.uk | Supervisor confirms the limits, response, communication and restart authority with the people doing this activity. | Stop if the agreed method, communication, competent cover or task limits cannot be maintained. |
| 6 | PPE | Select gloves, eye protection and any RPE for the actual formulation; a particulate mask does not protect against solvent vapour.Basis: Official task guidance: www.hse.gov.uk | Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence. | Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails. |
| 7 | Discipline | Maintain seals and extraction, check cleaning quality and investigate exposure or fire-control defects before restarting.Basis: Official task guidance: www.hse.gov.uk | Release only after maintenance owner accepts the cleaning trial and verified controls. Retain the checks and unresolved restrictions at handover. | Keep the activity on hold while defects or required reinstatement evidence remain unresolved. |
Source comparison
Table ID: chemical-safety-ericpd-hierarchy-for-chemical-safety-eseap
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Column 1
Elimination
- Column 2
Buy components ready for assembly or remove an unnecessary cleaning stage where cleanliness requirements permit.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed.
- Column 4
If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls.
Row 2
- Column 1
Substitution
- Column 2
Trial a suitable aqueous or other lower-hazard cleaning process; validate component finish and any new corrosion or skin risk.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Process/technical owner validates the alternative, its compatibility and any new risks before adoption.
- Column 4
Reject the alternative if suitability is unproved or its new hazards are unresolved.
Row 3
- Column 1
Engineering controls
- Column 2
Use a designated cleaning station away from ignition sources and unrelated work; segregate contaminated items and waste.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work.
- Column 4
Hold or stop for unknown solvent, failed extraction, uncontrolled vapour or incompatible waste.
Row 4
- Column 1
Engineering controls
- Column 2
Use compatible enclosed cleaning equipment and effective local extraction where required; minimise open liquid and splash paths.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Competent equipment/process owner checks product identity, enclosure, extraction, waste containment and cleaning quality.
- Column 4
Hold or stop for unknown solvent, failed extraction, uncontrolled vapour or incompatible waste.
Row 5
- Column 1
Administrative controls
- Column 2
Identify the product and contamination, control decanting and waste, and prohibit unassessed mixing or heating.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Supervisor confirms the limits, response, communication and restart authority with the people doing this activity.
- Column 4
Stop if the agreed method, communication, competent cover or task limits cannot be maintained.
Row 6
- Column 1
PPE
- Column 2
Select gloves, eye protection and any RPE for the actual formulation; a particulate mask does not protect against solvent vapour.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence.
- Column 4
Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails.
Row 7
- Column 1
Administrative controls
- Column 2
Maintain seals and extraction, check cleaning quality and investigate exposure or fire-control defects before restarting.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Release only after maintenance owner accepts the cleaning trial and verified controls. Retain the checks and unresolved restrictions at handover.
- Column 4
Keep the activity on hold while defects or required reinstatement evidence remain unresolved.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Elimination | Buy components ready for assembly or remove an unnecessary cleaning stage where cleanliness requirements permit.Basis: Official task guidance: www.hse.gov.uk | Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed. | If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls. |
| 2 | Substitution | Trial a suitable aqueous or other lower-hazard cleaning process; validate component finish and any new corrosion or skin risk.Basis: Official task guidance: www.hse.gov.uk | Process/technical owner validates the alternative, its compatibility and any new risks before adoption. | Reject the alternative if suitability is unproved or its new hazards are unresolved. |
| 3 | Engineering controls | Use a designated cleaning station away from ignition sources and unrelated work; segregate contaminated items and waste.Basis: Official task guidance: www.hse.gov.uk | Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work. | Hold or stop for unknown solvent, failed extraction, uncontrolled vapour or incompatible waste. |
| 4 | Engineering controls | Use compatible enclosed cleaning equipment and effective local extraction where required; minimise open liquid and splash paths.Basis: Official task guidance: www.hse.gov.uk | Competent equipment/process owner checks product identity, enclosure, extraction, waste containment and cleaning quality. | Hold or stop for unknown solvent, failed extraction, uncontrolled vapour or incompatible waste. |
| 5 | Administrative controls | Identify the product and contamination, control decanting and waste, and prohibit unassessed mixing or heating.Basis: Official task guidance: www.hse.gov.uk | Supervisor confirms the limits, response, communication and restart authority with the people doing this activity. | Stop if the agreed method, communication, competent cover or task limits cannot be maintained. |
| 6 | PPE | Select gloves, eye protection and any RPE for the actual formulation; a particulate mask does not protect against solvent vapour.Basis: Official task guidance: www.hse.gov.uk | Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence. | Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails. |
| 7 | Administrative controls | Maintain seals and extraction, check cleaning quality and investigate exposure or fire-control defects before restarting.Basis: Official task guidance: www.hse.gov.uk | Release only after maintenance owner accepts the cleaning trial and verified controls. Retain the checks and unresolved restrictions at handover. | Keep the activity on hold while defects or required reinstatement evidence remain unresolved. |
Source comparison
Table ID: chemical-safety-worked-control-hierarchy
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Column 1
Eliminate
- Column 2
Use a suitable supplied premix or closed bulk supply where it removes local bag opening and emptying.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed.
- Column 4
If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls.
Row 2
- Column 1
Reduce, including substitution
- Column 2
Choose a compatible less dusty granule, paste or liquid formulation where the process and full hazard review support it.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Process/technical owner validates the alternative, its compatibility and any new risks before adoption.
- Column 4
Reject the alternative if suitability is unproved or its new hazards are unresolved.
Row 3
- Column 1
Isolate
- Column 2
Enclose the charging area and separate nearby workers from the dust release and moving mixer parts.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work.
- Column 4
Hold or stop for failed capture, unknown ingredient, uncontrolled dust cloud or ignition-control defect.
Row 4
- Column 1
Control: physical safeguards
- Column 2
Use suitable contained charging and source extraction; assess ignition, static and explosion protection where dust is combustible.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Competent equipment/process owner checks ingredient identity, dust properties, extraction performance and charging access.
- Column 4
Hold or stop for failed capture, unknown ingredient, uncontrolled dust cloud or ignition-control defect.
Row 5
- Column 1
Control: work method and response
- Column 2
Verify ingredient identity and sequence; use the approved cleaning and waste method and keep hands away from moving parts.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Supervisor confirms the limits, response, communication and restart authority with the people doing this activity.
- Column 4
Stop if the agreed method, communication, competent cover or task limits cannot be maintained.
Row 6
- Column 1
PPE
- Column 2
Select suitable RPE and skin/eye protection for remaining exposure; fit-test any tight-fitting facepiece used.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence.
- Column 4
Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails.
Row 7
- Column 1
Discipline
- Column 2
Check capture, filters, seals and dust deposits; stop using the station when source control fails rather than finishing in RPE.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Release only after process owner accepts the charging method and functioning dust controls. Retain the checks and unresolved restrictions at handover.
- Column 4
Keep the activity on hold while defects or required reinstatement evidence remain unresolved.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Eliminate | Use a suitable supplied premix or closed bulk supply where it removes local bag opening and emptying.Basis: Official task guidance: www.hse.gov.uk | Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed. | If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls. |
| 2 | Reduce, including substitution | Choose a compatible less dusty granule, paste or liquid formulation where the process and full hazard review support it.Basis: Official task guidance: www.hse.gov.uk | Process/technical owner validates the alternative, its compatibility and any new risks before adoption. | Reject the alternative if suitability is unproved or its new hazards are unresolved. |
| 3 | Isolate | Enclose the charging area and separate nearby workers from the dust release and moving mixer parts.Basis: Official task guidance: www.hse.gov.uk | Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work. | Hold or stop for failed capture, unknown ingredient, uncontrolled dust cloud or ignition-control defect. |
| 4 | Control: physical safeguards | Use suitable contained charging and source extraction; assess ignition, static and explosion protection where dust is combustible.Basis: Official task guidance: www.hse.gov.uk | Competent equipment/process owner checks ingredient identity, dust properties, extraction performance and charging access. | Hold or stop for failed capture, unknown ingredient, uncontrolled dust cloud or ignition-control defect. |
| 5 | Control: work method and response | Verify ingredient identity and sequence; use the approved cleaning and waste method and keep hands away from moving parts.Basis: Official task guidance: www.hse.gov.uk | Supervisor confirms the limits, response, communication and restart authority with the people doing this activity. | Stop if the agreed method, communication, competent cover or task limits cannot be maintained. |
| 6 | PPE | Select suitable RPE and skin/eye protection for remaining exposure; fit-test any tight-fitting facepiece used.Basis: Official task guidance: www.hse.gov.uk | Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence. | Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails. |
| 7 | Discipline | Check capture, filters, seals and dust deposits; stop using the station when source control fails rather than finishing in RPE.Basis: Official task guidance: www.hse.gov.uk | Release only after process owner accepts the charging method and functioning dust controls. Retain the checks and unresolved restrictions at handover. | Keep the activity on hold while defects or required reinstatement evidence remain unresolved. |
Source comparison
Table ID: chemical-safety-worked-control-hierarchy-eseap
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Column 1
Elimination
- Column 2
Use a suitable supplied premix or closed bulk supply where it removes local bag opening and emptying.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed.
- Column 4
If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls.
Row 2
- Column 1
Substitution
- Column 2
Choose a compatible less dusty granule, paste or liquid formulation where the process and full hazard review support it.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Process/technical owner validates the alternative, its compatibility and any new risks before adoption.
- Column 4
Reject the alternative if suitability is unproved or its new hazards are unresolved.
Row 3
- Column 1
Engineering controls
- Column 2
Enclose the charging area and separate nearby workers from the dust release and moving mixer parts.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work.
- Column 4
Hold or stop for failed capture, unknown ingredient, uncontrolled dust cloud or ignition-control defect.
Row 4
- Column 1
Engineering controls
- Column 2
Use suitable contained charging and source extraction; assess ignition, static and explosion protection where dust is combustible.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Competent equipment/process owner checks ingredient identity, dust properties, extraction performance and charging access.
- Column 4
Hold or stop for failed capture, unknown ingredient, uncontrolled dust cloud or ignition-control defect.
Row 5
- Column 1
Administrative controls
- Column 2
Verify ingredient identity and sequence; use the approved cleaning and waste method and keep hands away from moving parts.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Supervisor confirms the limits, response, communication and restart authority with the people doing this activity.
- Column 4
Stop if the agreed method, communication, competent cover or task limits cannot be maintained.
Row 6
- Column 1
PPE
- Column 2
Select suitable RPE and skin/eye protection for remaining exposure; fit-test any tight-fitting facepiece used.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence.
- Column 4
Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails.
Row 7
- Column 1
Administrative controls
- Column 2
Check capture, filters, seals and dust deposits; stop using the station when source control fails rather than finishing in RPE.Basis: Official task guidance: www.hse.gov.uk
- Column 3
Release only after process owner accepts the charging method and functioning dust controls. Retain the checks and unresolved restrictions at handover.
- Column 4
Keep the activity on hold while defects or required reinstatement evidence remain unresolved.
Read the complete comparison table
| Row | Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|---|
| 1 | Elimination | Use a suitable supplied premix or closed bulk supply where it removes local bag opening and emptying.Basis: Official task guidance: www.hse.gov.uk | Process owner verifies that the revised workflow achieves the required output and the hazardous step is genuinely removed. | If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls. |
| 2 | Substitution | Choose a compatible less dusty granule, paste or liquid formulation where the process and full hazard review support it.Basis: Official task guidance: www.hse.gov.uk | Process/technical owner validates the alternative, its compatibility and any new risks before adoption. | Reject the alternative if suitability is unproved or its new hazards are unresolved. |
| 3 | Engineering controls | Enclose the charging area and separate nearby workers from the dust release and moving mixer parts.Basis: Official task guidance: www.hse.gov.uk | Supervisor verifies the task boundaries and that the separation or isolation protects affected people and connected work. | Hold or stop for failed capture, unknown ingredient, uncontrolled dust cloud or ignition-control defect. |
| 4 | Engineering controls | Use suitable contained charging and source extraction; assess ignition, static and explosion protection where dust is combustible.Basis: Official task guidance: www.hse.gov.uk | Competent equipment/process owner checks ingredient identity, dust properties, extraction performance and charging access. | Hold or stop for failed capture, unknown ingredient, uncontrolled dust cloud or ignition-control defect. |
| 5 | Administrative controls | Verify ingredient identity and sequence; use the approved cleaning and waste method and keep hands away from moving parts.Basis: Official task guidance: www.hse.gov.uk | Supervisor confirms the limits, response, communication and restart authority with the people doing this activity. | Stop if the agreed method, communication, competent cover or task limits cannot be maintained. |
| 6 | PPE | Select suitable RPE and skin/eye protection for remaining exposure; fit-test any tight-fitting facepiece used.Basis: Official task guidance: www.hse.gov.uk | Assessor confirms whether PPE is needed and checks selection, condition, compatibility and any required face-fit evidence. | Do not rely on unsuitable or defective protection, or use PPE to continue after an essential source control fails. |
| 7 | Administrative controls | Check capture, filters, seals and dust deposits; stop using the station when source control fails rather than finishing in RPE.Basis: Official task guidance: www.hse.gov.uk | Release only after process owner accepts the charging method and functioning dust controls. Retain the checks and unresolved restrictions at handover. | Keep the activity on hold while defects or required reinstatement evidence remain unresolved. |
Storage and compatibility controls
Table ID: chemical-safety-storage-and-compatibility-controls
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Storage issue
Labelling
- Why it matters
Workers need to identify contents and hazards quickly.
- Good practice
Keep original labels or approved workplace labels on all containers.
Row 2
- Storage issue
Segregation
- Why it matters
Incompatible substances may react if mixed.
- Good practice
Separate acids, alkalis, oxidisers, flammables and toxics as required.
Row 3
- Storage issue
Containment
- Why it matters
Leaks can spread, reach drains or contact other chemicals.
- Good practice
Use bunds, trays and suitable cabinets.
Row 4
- Storage issue
Ventilation
- Why it matters
Vapours can accumulate and create inhalation or fire risk.
- Good practice
Provide suitable natural or mechanical ventilation.
Row 5
- Storage issue
Ignition control
- Why it matters
Flammable vapours may ignite.
- Good practice
Control hot work, electrical equipment, static and smoking.
Row 6
- Storage issue
Access control
- Why it matters
Untrained people may misuse or move chemicals.
- Good practice
Restrict stores and keep issue controls.
Row 7
- Storage issue
Stock rotation
- Why it matters
Old or degraded chemicals can become unstable or unknown.
- Good practice
Use stock checks, expiry dates and disposal routes.
Read the complete comparison table
| Row | Storage issue | Why it matters | Good practice |
|---|---|---|---|
| 1 | Labelling | Workers need to identify contents and hazards quickly. | Keep original labels or approved workplace labels on all containers. |
| 2 | Segregation | Incompatible substances may react if mixed. | Separate acids, alkalis, oxidisers, flammables and toxics as required. |
| 3 | Containment | Leaks can spread, reach drains or contact other chemicals. | Use bunds, trays and suitable cabinets. |
| 4 | Ventilation | Vapours can accumulate and create inhalation or fire risk. | Provide suitable natural or mechanical ventilation. |
| 5 | Ignition control | Flammable vapours may ignite. | Control hot work, electrical equipment, static and smoking. |
| 6 | Access control | Untrained people may misuse or move chemicals. | Restrict stores and keep issue controls. |
| 7 | Stock rotation | Old or degraded chemicals can become unstable or unknown. | Use stock checks, expiry dates and disposal routes. |
Monitoring and maintenance evidence
Table ID: chemical-safety-monitoring-and-maintenance-evidence
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Control or evidence
Chemical register
- What to check
Substances, locations, SDS dates, assessment status and owner.
- Typical frequency trigger
New chemical, periodic review and stock check.
Row 2
- Control or evidence
COSHH assessments
- What to check
Task-specific exposure routes and controls.
- Typical frequency trigger
Process change, SDS change, incident, symptom or review cycle.
Row 3
- Control or evidence
LEV
- What to check
Capture performance, condition, user checks and thorough examination.
- Typical frequency trigger
User checks plus thorough examination at required intervals.
Row 4
- Control or evidence
RPE
- What to check
Suitability, fit test, condition, storage, cleaning and wearer training.
- Typical frequency trigger
Before use, issue, change in wearer or task.
Row 5
- Control or evidence
Exposure monitoring
- What to check
Airborne concentration or biological monitoring where justified.
- Typical frequency trigger
WEL, uncertainty, high-risk substance or control verification.
Row 6
- Control or evidence
Storage checks
- What to check
Segregation, labels, containment, quantities and housekeeping.
- Typical frequency trigger
Routine inspection and stock review.
Row 7
- Control or evidence
Incident and symptom trends
- What to check
Spills, odour complaints, skin reports, breathing symptoms and near misses.
- Typical frequency trigger
Every report and periodic trend review.
Read the complete comparison table
| Row | Control or evidence | What to check | Typical frequency trigger |
|---|---|---|---|
| 1 | Chemical register | Substances, locations, SDS dates, assessment status and owner. | New chemical, periodic review and stock check. |
| 2 | COSHH assessments | Task-specific exposure routes and controls. | Process change, SDS change, incident, symptom or review cycle. |
| 3 | LEV | Capture performance, condition, user checks and thorough examination. | User checks plus thorough examination at required intervals. |
| 4 | RPE | Suitability, fit test, condition, storage, cleaning and wearer training. | Before use, issue, change in wearer or task. |
| 5 | Exposure monitoring | Airborne concentration or biological monitoring where justified. | WEL, uncertainty, high-risk substance or control verification. |
| 6 | Storage checks | Segregation, labels, containment, quantities and housekeeping. | Routine inspection and stock review. |
| 7 | Incident and symptom trends | Spills, odour complaints, skin reports, breathing symptoms and near misses. | Every report and periodic trend review. |
Chemical health surveillance examples
Table ID: chemical-safety-chemical-health-surveillance-examples
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Exposure type
Skin irritants or sensitisers
- Possible surveillance
Skin checks and symptom reporting.
- Management use
Detect dermatitis and review gloves, washing and exposure.
Row 2
- Exposure type
Respiratory sensitisers
- Possible surveillance
Questionnaires and lung-function surveillance.
- Management use
Detect work-related asthma symptoms early.
Row 3
- Exposure type
Substances with biological monitoring
- Possible surveillance
Biological samples where appropriate and advised.
- Management use
Assess uptake where air monitoring alone is not enough.
Row 4
- Exposure type
Carcinogens or mutagens
- Possible surveillance
Records and surveillance where required by risk assessment.
- Management use
Support long-term exposure control and evidence.
Row 5
- Exposure type
High concern symptoms
- Possible surveillance
Occupational health referral.
- Management use
Assess fitness, restrictions and control failures.
Read the complete comparison table
| Row | Exposure type | Possible surveillance | Management use |
|---|---|---|---|
| 1 | Skin irritants or sensitisers | Skin checks and symptom reporting. | Detect dermatitis and review gloves, washing and exposure. |
| 2 | Respiratory sensitisers | Questionnaires and lung-function surveillance. | Detect work-related asthma symptoms early. |
| 3 | Substances with biological monitoring | Biological samples where appropriate and advised. | Assess uptake where air monitoring alone is not enough. |
| 4 | Carcinogens or mutagens | Records and surveillance where required by risk assessment. | Support long-term exposure control and evidence. |
| 5 | High concern symptoms | Occupational health referral. | Assess fitness, restrictions and control failures. |
Chemical duties by location
Table ID: chemical-safety-jurisdiction-map
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Column-1
Workplace exposure
- Column-2
COSHH 2002; HSE guidance.
- Column-3
COSHH (NI) 2003; HSENI guidance.
Row 2
- Column-1
Dangerous substance/fire
- Column-2
DSEAR 2002 where relevant.
- Column-3
DSEAR (NI) 2003 where relevant.
Row 3
- Column-1
Supply market
- Column-2
GB CLP and UK REACH.
- Column-3
EU CLP and EU REACH.
Read the complete comparison table
| Row | Column-1 | Column-2 | Column-3 |
|---|---|---|---|
| 1 | Workplace exposure | COSHH 2002; HSE guidance. | COSHH (NI) 2003; HSENI guidance. |
| 2 | Dangerous substance/fire | DSEAR 2002 where relevant. | DSEAR (NI) 2003 where relevant. |
| 3 | Supply market | GB CLP and UK REACH. | EU CLP and EU REACH. |
Crownway chemical safety system
Table ID: chemical-safety-crownway-chemical-safety-system
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- System element
Chemical register
- Example control
Approved chemicals, SDS version, location, owner, COSHH status and DSEAR relevance.
- How it is checked
Monthly stores check and annual register review.
Row 2
- System element
Procurement
- Example control
No unapproved substance enters site without SDS and compatibility review.
- How it is checked
Purchase approval and supplier review.
Row 3
- System element
Risk assessment
- Example control
Task-based COSHH assessments for fuels, additives, cleaners, residues and laboratory chemicals.
- How it is checked
Supervisor briefing and HSSE audit.
Row 4
- System element
Storage
- Example control
Segregated cabinets, bunding, labelling, flammable storage and spill equipment.
- How it is checked
Inspection checklist and action close-out.
Row 5
- System element
Training
- Example control
Awareness for all, task training for users, supervisor assurance training and spill response drills.
- How it is checked
Training matrix, practical observation and refresher plan.
Row 6
- System element
Contractor control
- Example control
Contractors submit SDS and method controls before work.
- How it is checked
Permit review and site monitoring.
Row 7
- System element
Learning
- Example control
Odour, spill, exposure, PPE and storage findings are trended.
- How it is checked
Management review and improvement actions.
Read the complete comparison table
| Row | System element | Example control | How it is checked |
|---|---|---|---|
| 1 | Chemical register | Approved chemicals, SDS version, location, owner, COSHH status and DSEAR relevance. | Monthly stores check and annual register review. |
| 2 | Procurement | No unapproved substance enters site without SDS and compatibility review. | Purchase approval and supplier review. |
| 3 | Risk assessment | Task-based COSHH assessments for fuels, additives, cleaners, residues and laboratory chemicals. | Supervisor briefing and HSSE audit. |
| 4 | Storage | Segregated cabinets, bunding, labelling, flammable storage and spill equipment. | Inspection checklist and action close-out. |
| 5 | Training | Awareness for all, task training for users, supervisor assurance training and spill response drills. | Training matrix, practical observation and refresher plan. |
| 6 | Contractor control | Contractors submit SDS and method controls before work. | Permit review and site monitoring. |
| 7 | Learning | Odour, spill, exposure, PPE and storage findings are trended. | Management review and improvement actions. |
Role-level learning and competence evidence
Table ID: chemical-safety-competence-decisions
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Column-1
Buyer and assessor: product change.
- Column-2
Check label, SDS, market and actual task before approval.
- Column-3
Product approval and task assessment; revisit after formulation change.
Row 2
- Column-1
Worker and supervisor: safe use.
- Column-2
Demonstrate transfer, exposure controls and stop response at the job.
- Column-3
Observed competence; repeat after near miss.
Row 3
- Column-1
Engineer: source controls.
- Column-2
Inspect extraction, containment and isolation against design.
- Column-3
Test and maintenance record; repair failures before restart.
Row 4
- Column-1
Emergency lead: release drill.
- Column-2
Practise alarm, evacuation, 999 handover and safe isolation.
- Column-3
Drill outcome and closed actions.
Read the complete comparison table
| Row | Column-1 | Column-2 | Column-3 |
|---|---|---|---|
| 1 | Buyer and assessor: product change. | Check label, SDS, market and actual task before approval. | Product approval and task assessment; revisit after formulation change. |
| 2 | Worker and supervisor: safe use. | Demonstrate transfer, exposure controls and stop response at the job. | Observed competence; repeat after near miss. |
| 3 | Engineer: source controls. | Inspect extraction, containment and isolation against design. | Test and maintenance record; repair failures before restart. |
| 4 | Emergency lead: release drill. | Practise alarm, evacuation, 999 handover and safe isolation. | Drill outcome and closed actions. |
Study application
Table ID: chemical-safety-study-application
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Study area
Routes of entry
- What to know
Inhalation, skin, eyes, ingestion and injection.
- How to apply it in a scenario
Match the route to controls, not generic PPE.
Row 2
- Study area
Forms
- What to know
Dust, fume, mist, vapour, gas, liquid, powder and process-generated substances.
- How to apply it in a scenario
Explain why the work method changes the risk.
Row 3
- Study area
COSHH assessment
- What to know
Hazard, exposure, people, task, controls, monitoring and review.
- How to apply it in a scenario
Identify missing assessment details and improvement actions.
Row 4
- Study area
Control hierarchy
- What to know
Eliminate, reduce, isolate, control, PPE and discipline.
- How to apply it in a scenario
Rank controls from strongest to weakest.
Row 5
- Study area
Monitoring and surveillance
- What to know
WELs, LEV checks, exposure monitoring and health surveillance triggers.
- How to apply it in a scenario
Use evidence to judge whether controls are effective.
Row 6
- Study area
Emergency arrangements
- What to know
Spill, splash, inhalation, fire and release response.
- How to apply it in a scenario
Explain what workers need to know and practise.
Read the complete comparison table
| Row | Study area | What to know | How to apply it in a scenario |
|---|---|---|---|
| 1 | Routes of entry | Inhalation, skin, eyes, ingestion and injection. | Match the route to controls, not generic PPE. |
| 2 | Forms | Dust, fume, mist, vapour, gas, liquid, powder and process-generated substances. | Explain why the work method changes the risk. |
| 3 | COSHH assessment | Hazard, exposure, people, task, controls, monitoring and review. | Identify missing assessment details and improvement actions. |
| 4 | Control hierarchy | Eliminate, reduce, isolate, control, PPE and discipline. | Rank controls from strongest to weakest. |
| 5 | Monitoring and surveillance | WELs, LEV checks, exposure monitoring and health surveillance triggers. | Use evidence to judge whether controls are effective. |
| 6 | Emergency arrangements | Spill, splash, inhalation, fire and release response. | Explain what workers need to know and practise. |
Source tables and records 4
Warning signs and likely harm
Table ID: chemical-safety-warning-signs-and-likely-harm
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Warning sign
Outdated or missing SDS
- How harm can develop
Controls may be based on old classification or missing emergency information.
- Immediate management response
Obtain current SDS and review COSHH assessment.
Row 2
- Warning sign
Generic COSHH assessment
- How harm can develop
Actual routes of exposure are missed.
- Immediate management response
Rewrite around the real task and people exposed.
Row 3
- Warning sign
Unlabelled decanted containers
- How harm can develop
Wrong use, ingestion, mixing or emergency confusion can occur.
- Immediate management response
Stop use, identify contents and improve labelling controls.
Row 4
- Warning sign
Strong odours or visible dust
- How harm can develop
Inhalation exposure may be uncontrolled.
- Immediate management response
Check ventilation, process controls and exposure monitoring need.
Row 5
- Warning sign
Poor glove condition
- How harm can develop
Skin exposure, burns or absorption can occur.
- Immediate management response
Review compatibility, use, storage and replacement.
Row 6
- Warning sign
Incompatible storage
- How harm can develop
Leaks can create reaction, gas, heat, fire or toxic release.
- Immediate management response
Segregate, inspect and update storage plan.
Row 7
- Warning sign
Repeated skin or breathing symptoms
- How harm can develop
Controls may be failing or sensitisation may be developing.
- Immediate management response
Escalate through occupational health and review exposure controls.
Row 8
- Warning sign
Spill kits empty or unused
- How harm can develop
Small releases can become exposure or environmental incidents.
- Immediate management response
Restock, train and drill.
Read the complete comparison table
| Row | Warning sign | How harm can develop | Immediate management response |
|---|---|---|---|
| 1 | Outdated or missing SDS | Controls may be based on old classification or missing emergency information. | Obtain current SDS and review COSHH assessment. |
| 2 | Generic COSHH assessment | Actual routes of exposure are missed. | Rewrite around the real task and people exposed. |
| 3 | Unlabelled decanted containers | Wrong use, ingestion, mixing or emergency confusion can occur. | Stop use, identify contents and improve labelling controls. |
| 4 | Strong odours or visible dust | Inhalation exposure may be uncontrolled. | Check ventilation, process controls and exposure monitoring need. |
| 5 | Poor glove condition | Skin exposure, burns or absorption can occur. | Review compatibility, use, storage and replacement. |
| 6 | Incompatible storage | Leaks can create reaction, gas, heat, fire or toxic release. | Segregate, inspect and update storage plan. |
| 7 | Repeated skin or breathing symptoms | Controls may be failing or sensitisation may be developing. | Escalate through occupational health and review exposure controls. |
| 8 | Spill kits empty or unused | Small releases can become exposure or environmental incidents. | Restock, train and drill. |
Official links and their use
Table ID: chemical-safety-official-links
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Column-1
HSE using chemicals at work
- Column-2
Great Britain regulator
- Column-3
Chemical handling and assessment
Row 2
- Column-1
HSE COSHH basics
- Column-2
Great Britain regulator
- Column-3
Exposure duties and controls
Row 3
- Column-1
HSE COSHH assessment
- Column-2
Great Britain regulator
- Column-3
Task-specific assessment
Row 4
- Column-1
HSE safety data sheets and COSHH
- Column-2
Great Britain regulator
- Column-3
SDS informs but does not replace assessment
Row 5
- Column-1
HSE CLP in GB and NI
- Column-2
Great Britain and Northern Ireland supply boundary
- Column-3
GB CLP versus EU CLP
Row 6
- Column-1
HSE UK REACH
- Column-2
Great Britain and Northern Ireland supply boundary
- Column-3
UK REACH GB and EU REACH NI
Row 7
- Column-1
HSE DSEAR
- Column-2
Great Britain regulator
- Column-3
Fire and explosion duties where relevant
Row 8
- Column-1
HSE local exhaust ventilation
- Column-2
Great Britain regulator
- Column-3
Source capture and examination
Row 9
- Column-1
HSE COSHH health surveillance
- Column-2
Great Britain regulator
- Column-3
Risk-based surveillance, not a substitute for control
Row 10
- Column-1
HSENI COSHH
- Column-2
Northern Ireland regulator
- Column-3
NI workplace exposure duty
Row 11
- Column-1
HSENI subordinate legislation list
- Column-2
Northern Ireland legislation index
- Column-3
NI DSEAR 2003 instrument
Row 12
- Column-1
HSE Managing for health and safety (HSG65)
- Column-2
HSE management guidance for Great Britain; check current edition
- Column-3
Plan–do–check–act management guidance
Row 13
- Column-1
HSE five-level hierarchy
- Column-2
Great Britain / HSE
- Column-3
Choose elimination, substitution, engineering, administrative controls and PPE in order
Row 14
- Column-1
HSE choosing protective gloves
- Column-2
Great Britain / HSE
- Column-3
Product, wearer, contact duration and manufacturer performance data
Read the complete comparison table
| Row | Column-1 | Column-2 | Column-3 |
|---|---|---|---|
| 1 | HSE using chemicals at work | Great Britain regulator | Chemical handling and assessment |
| 2 | HSE COSHH basics | Great Britain regulator | Exposure duties and controls |
| 3 | HSE COSHH assessment | Great Britain regulator | Task-specific assessment |
| 4 | HSE safety data sheets and COSHH | Great Britain regulator | SDS informs but does not replace assessment |
| 5 | HSE CLP in GB and NI | Great Britain and Northern Ireland supply boundary | GB CLP versus EU CLP |
| 6 | HSE UK REACH | Great Britain and Northern Ireland supply boundary | UK REACH GB and EU REACH NI |
| 7 | HSE DSEAR | Great Britain regulator | Fire and explosion duties where relevant |
| 8 | HSE local exhaust ventilation | Great Britain regulator | Source capture and examination |
| 9 | HSE COSHH health surveillance | Great Britain regulator | Risk-based surveillance, not a substitute for control |
| 10 | HSENI COSHH | Northern Ireland regulator | NI workplace exposure duty |
| 11 | HSENI subordinate legislation list | Northern Ireland legislation index | NI DSEAR 2003 instrument |
| 12 | HSE Managing for health and safety (HSG65) | HSE management guidance for Great Britain; check current edition | Plan–do–check–act management guidance |
| 13 | HSE five-level hierarchy | Great Britain / HSE | Choose elimination, substitution, engineering, administrative controls and PPE in order |
| 14 | HSE choosing protective gloves | Great Britain / HSE | Product, wearer, contact duration and manufacturer performance data |
Acronyms and plain-English meanings
Table ID: chemical-safety-acronyms-and-plain-english-meanings
Source: https://www.sharehub.ltd/knowledge-hub/chemical-safety.html
Row 1
- Term
COSHH
- Meaning
Control of Substances Hazardous to Health
- Plain english use
Workplace regulations for preventing or controlling exposure to hazardous substances.
Row 2
- Term
SDS
- Meaning
Safety Data Sheet
- Plain english use
Supplier document used to inform, but not replace, workplace risk assessment.
Row 3
- Term
CLP
- Meaning
Classification, Labelling and Packaging
- Plain english use
Chemical hazard classification and labelling system.
Row 4
- Term
REACH
- Meaning
Registration, Evaluation, Authorisation and Restriction of Chemicals
- Plain english use
Chemical supply-chain and restriction framework.
Row 5
- Term
WEL
- Meaning
Workplace Exposure Limit
- Plain english use
Legal airborne exposure limit listed in EH40 for certain substances.
Row 6
- Term
LEV
- Meaning
Local Exhaust Ventilation
- Plain english use
Engineering control that captures airborne contaminants at source.
Row 7
- Term
RPE
- Meaning
Respiratory Protective Equipment
- Plain english use
Respirators and masks used where residual airborne exposure remains.
Row 8
- Term
PPE
- Meaning
Personal Protective Equipment
- Plain english use
Gloves, goggles, face shields, coveralls and other worn protection.
Row 9
- Term
DSEAR
- Meaning
Dangerous Substances and Explosive Atmospheres Regulations
- Plain english use
Rules for fire and explosion risks from dangerous substances.
Row 10
- Term
SVHC
- Meaning
Substance of Very High Concern
- Plain english use
REACH term for substances with serious health or environmental concern.
Row 11
- Term
ALARP
- Meaning
As Low As Reasonably Practicable
- Plain english use
A stricter exposure-control expectation for certain higher-risk substances.
Row 12
- Term
APF
- Meaning
Assigned Protection Factor
- Plain english use
RPE protection rating used when selecting respirators.
Read the complete comparison table
| Row | Term | Meaning | Plain english use |
|---|---|---|---|
| 1 | COSHH | Control of Substances Hazardous to Health | Workplace regulations for preventing or controlling exposure to hazardous substances. |
| 2 | SDS | Safety Data Sheet | Supplier document used to inform, but not replace, workplace risk assessment. |
| 3 | CLP | Classification, Labelling and Packaging | Chemical hazard classification and labelling system. |
| 4 | REACH | Registration, Evaluation, Authorisation and Restriction of Chemicals | Chemical supply-chain and restriction framework. |
| 5 | WEL | Workplace Exposure Limit | Legal airborne exposure limit listed in EH40 for certain substances. |
| 6 | LEV | Local Exhaust Ventilation | Engineering control that captures airborne contaminants at source. |
| 7 | RPE | Respiratory Protective Equipment | Respirators and masks used where residual airborne exposure remains. |
| 8 | PPE | Personal Protective Equipment | Gloves, goggles, face shields, coveralls and other worn protection. |
| 9 | DSEAR | Dangerous Substances and Explosive Atmospheres Regulations | Rules for fire and explosion risks from dangerous substances. |
| 10 | SVHC | Substance of Very High Concern | REACH term for substances with serious health or environmental concern. |
| 11 | ALARP | As Low As Reasonably Practicable | A stricter exposure-control expectation for certain higher-risk substances. |
| 12 | APF | Assigned Protection Factor | RPE protection rating used when selecting respirators. |