Competence and role readiness

Approx. 70–105 minutes

Independent SHAREhub process-safety awareness. Selected learning maps to a numbered process-safety syllabus topic; this is not the NEBOSH qualification, approved provision, specialist design instruction or work authorisation. GB guidance is distinguished from corresponding NI requirements; establish applicability for the actual jurisdiction and establishment.

This reader supplies the complete teaching. Use the interactive LMS course for assessed activities, saved progress and completion.

LESSON 1

Start with the critical task

Connect competence to a specific process function.

Process operators monitoring equipment from a UK industrial control room
Existing SHAREhub photographic illustration. The written fictional case supplies the condition and decision evidence.

Start with the critical task

A role is safety-critical because of what it must reliably do in a credible scenario, not because its title sounds senior. Identify the task, required information, decision limits and consequence of an error. Routine and abnormal tasks may demand different capabilities.

Begin with the work rather than a list of training courses. Who identifies a route, verifies an isolation or responds to a deviation? The competence arrangements should cover the actual function and its interfaces. Awareness training helps recognise that need but does not authorise the learner to perform the task.

Which roles and tasks are process-safety-critical?

A task is critical when a foreseeable error could initiate, fail to detect, or fail to limit a major accident; role titles alone are too broad.

The HSE competence guidance ties assurance to responsibilities and tasks identified in risk assessment. At a fuel terminal, tank line-up, high-high alarm response, proof testing, permit issue, isolation verification and emergency command may each need a different standard. The assessor should map scenarios and barriers, observe who actually acts, include contractors and managers, and account for nights, start-up, upset and maintenance. Do not call every employee “safety critical” without showing the specific barrier task and potential consequence.

Applied case

Fictional exercise: A supervisor lists course attendance but cannot identify who is competent to accept a process handback.

Role

A title identifies a position.

Task

The function and conditions define what capability is needed.

Test your decision

What should be established?

  1. The task-specific competence and authority requirements for handback acceptance.
  2. Only the number of certificates.
  3. That every supervisor can approve every process task.
Compare the explanation

The task-specific competence and authority requirements for handback acceptance.

Competence must connect to the actual critical function.

Open this interactive lesson →

LESSON 2

Describe capability, not confidence

Separate knowledge, skill and practical application.

Process operators monitoring equipment from a UK industrial control room. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Avoid / redesign: Avoid a nonessential transfer or overfill-prone routing. Control the task: Specify an independent high-high level trip, closure time and containment capacity against the overfill scenario; document alarm set point and safe transfer rate. Verify before release: Planning lead verifies need; hold task if safe route is unknown.

Describe capability, not confidence

Knowing an instruction, performing a task and exercising judgement in context are related but distinct. A competence framework should describe the required capability and evidence for the role, including abnormal situations and limits on independent work.

Confidence can help communication but is not proof of competence. Likewise, years in a trade do not establish familiarity with every local process. Use relevant experience, training and assessed application together. Record the scope so an assessment for one system is not silently treated as approval for all similar-looking equipment.

How should a competence framework be built?

A competence framework should be built from hazards, barriers and critical tasks rather than from generic job descriptions.

A useful framework begins with scenarios: tank overfill, toxic release, runaway reaction, failed isolation, vapour cloud ignition, emergency shutdown, relief-system demand or loss of containment during maintenance. The framework then asks which tasks prevent, detect or mitigate that scenario and what people must be able to do under normal, abnormal and emergency conditions.

The result should be a matrix that is specific enough to audit. It should show required knowledge, practical task assessment, simulator or drill requirements where useful, refresher interval, assessor competence, authorisation level, restrictions and records.

Competence framework design
StepWhat to defineEvidence
Map scenariosCredible major accident events and barriers.Hazard register and bowties/LOPA where used.
Identify critical tasksTasks and decisions that affect barriers.Task inventory and role matrix.
Define standardsKnowledge, skill, judgement and behaviour required.Competence standard or role profile.
Assess competenceHow performance will be tested.Assessment criteria, assessor records and results.
Authorise roleWho may perform, supervise or approve work.Authorisation register.
Review and refreshWhen competence is reassessed.Refresher plan and trigger list.

Applied case

Fictional exercise: An experienced contractor has not worked with the site’s process isolation arrangements.

Knowledge

The person can explain relevant information.

Application

They can use it correctly within the assessed task and conditions.

Test your decision

What remains?

  1. Nothing because experience covers all sites.
  2. A general confidence statement.
  3. Assessment of the relevant local task capability and authority boundary.
Compare the explanation

Assessment of the relevant local task capability and authority boundary.

Relevant experience contributes evidence but does not remove local requirements.

Open this interactive lesson →

LESSON 3

Choose evidence that shows performance

Distinguish attendance from task assessment.

Process operators monitoring equipment from a UK industrial control room. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Change at source: Avoid a nonessential transfer or overfill-prone routing. Make it observable: Planning lead verifies need; hold task if safe route is unknown. Keep useful evidence: Major accident hazard register, bowties and competence matrix.

Choose evidence that shows performance

Assessment needs evidence relevant to the task. It can include explanation, observed performance and suitable exercises for infrequent conditions. The method must be safe and appropriate; do not create a live hazardous condition to test a learner.

A competent assessor should examine the decisions and errors that matter, with a recorded scope and result. A multiple-choice pass or attendance sheet may support learning but cannot alone establish practical task capability. Identify gaps, supervision needs and the route to reassessment rather than treating every result as a permanent unrestricted authorisation.

Build a task-based competence decision

Attendance, demonstrated capability and employer authorisation answer different questions. The evidence must match the actual safety-critical task.

Fictional learning example

Separate the evidence from the decision
Part of the pictureWhat the example establishes
AttendanceA person has completed an awareness course.
Task evidenceThere is no observed assessment for the plant-specific isolation task.
Operating contextThe task is infrequent and would take place during an abnormal outage.

Pause and decide: Can awareness-course completion establish readiness for this task?

Compare the reasoning

No. Define the task, limits and required performance, then use the relevant assessment and authorisation arrangements. Review supervision, workload and access to help. Refresh the evidence when the plant, procedure, role or performance changes.

How should competence be demonstrated?

Test knowledge, observed task performance and judgement in credible abnormal conditions against the actual barrier standard.

HSE says training alone is insufficient. For a tank-transfer operator, assess line-up and independent verification, response to a stuck level indicator, interpretation of a high-high alarm, stop/isolating action, communication and hand-back. Use simulation or scenario questioning for rare events, then observed supervised practice on permitted plant states. The assessor must know the task and failure criteria; a course certificate or years of service cannot replace current evidence. If the person cannot explain an abnormal response, restrict authorisation, coach and reassess before unsupervised duty.

On a small screen, scroll this table sideways to read all columns.

Assess a transfer operator
Competence elementAssessment evidenceFailure response
Normal line-upObserved valve and tank check against current procedure.Hold authorisation for wrong line-up.
Abnormal indicationScenario: level instrument disagreement or alarm inhibition.Stop transfer, verify state and call competent support.
Emergency actionDrill/simulator for shutdown and handover.Retrain and retest if action/communication misses standard.
CurrencyRecord last practice, change and restriction.Supervision/reassessment after long absence or material change.

Agree the assessor’s task-specific acceptance criteria before the assessment: cues, decision, safe action, timing where the scenario requires it, escalation and hand-back evidence. Use a simulator or a controlled permitted plant state for abnormal scenarios; do not create a live hazardous upset to test a trainee. Record observed results and restrictions, check that the shift has current authorised cover, and stop or reassign the critical task if that cover is missing. After a failed assessment, change or prolonged absence, the role owner sets supervision/coaching and reassesses before restoring unsupervised authority. HSE competence guidance supports task standards and assessment beyond course attendance.

Applied case

Fictional exercise: A person attends a briefing but has never demonstrated the changed handback task.

Attendance

The learning event was attended.

Demonstration

Task-relevant application still needs evidence.

Test your decision

What is missing?

  1. A live uncontrolled failure to test reactions.
  2. Appropriate evidence of task performance and decision capability.
  3. Only a printed certificate.
Compare the explanation

Appropriate evidence of task performance and decision capability.

Assessment must be relevant and safe.

Open this interactive lesson →

LESSON 4

Keep authorisation within scope

Distinguish assessed competence from permission to act.

Process operators monitoring equipment from a UK industrial control room. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Assess and analyse: Maps critical roles to overfill, loss of containment, ignition, emergency and escalation barriers. Define standards: Sets task standards for alarm response, permits, isolations, loading, emergency roles and technical approvals. Assess and authorise: Uses practical observations, scenario questions, drills and supervisor endorsement before authorisation.

Keep authorisation within scope

Competence and authorisation answer different questions. A person may be capable but not appointed to make a particular operating decision. Conversely, a signature on an appointment cannot create capability that has not been established.

State equipment, task, conditions, supervision and decision limits as appropriate. Make the boundary available to both the person and those allocating work. If the task changes or the authorisation has conditions, do not assume an old record covers the new arrangement. Use the employer’s defined review rather than inventing a universal expiry period.

How should authorisation and supervision be controlled?

Authorisation and supervision should ensure that only competent, current and properly supported people perform or approve safety-critical work.

Authorisation should be formal because informal permission drifts. The system should state who can start up, shut down, issue permits, override alarms, accept equipment back into service, approve temporary repairs, defer inspections, lead emergency response or supervise contractors.

Supervision is a live control, especially for trainees, infrequent tasks, abnormal conditions, contractors and work under production pressure. Good supervisors check conditions, ask questions, verify controls and stop work when competence, information or barriers are uncertain.

Authorisation controls
ControlWhat it should coverEvidence
Authorisation registerNames, roles, restrictions, expiry and approval level.Current register and review history.
Temporary authorisationShort-term permission with risk controls.Justification, limits, supervisor and expiry.
RestrictionsTasks the person may not perform alone.Role profile and supervisor briefing.
Supervision standardLevel of oversight for task and experience.Supervisor checks and coaching records.
Withdrawal processHow authorisation is paused after concern, change or absence.Case record and reassessment plan.

Applied case

Fictional exercise: An authorisation covers one process area; the person is asked to approve another unfamiliar area.

Capable

Evidence concerns a defined task.

Appointed

Permission has a defined role and boundary.

Test your decision

What is sound?

  1. Check the new task’s competence and authority requirements before allocation.
  2. Extend approval automatically because the title is the same.
  3. Assume the person must be incompetent everywhere.
Compare the explanation

Check the new task’s competence and authority requirements before allocation.

Scope matters without devaluing demonstrated capability.

Open this interactive lesson →

LESSON 5

Review capability when the basis changes

Identify meaningful reassessment triggers.

2D teaching diagram: Make critical work manageable for people
Existing SHAREhub 2D teaching schematic. Use alongside the explanation and fictional case in this lesson.

Review capability when the basis changes

Competence can need review after changes in task, equipment, role or evidence of performance. Long absence from a rare task and findings from an incident may also matter. A calendar entry alone cannot show that capability remains relevant.

The responsible competence system establishes appropriate review and refresher arrangements. This course supplies no universal retraining period. Ask what changed, which capability may be affected and what evidence would resolve the question. Avoid treating refresher training as an automatic cure for a problem caused by unclear equipment or impossible task demands.

How can competence erosion be prevented?

Competence erosion can be prevented by planned refresher training, reassessment, practice, learning from events and reassessment after change or long gaps.

Competence decays when a task is rarely performed, procedures change, automation removes hands-on experience, experienced people leave, contractors rotate, abnormal events are not practised or people normalise workarounds. The problem is often invisible until the person has to act under pressure.

Refreshers should be risk-based. A rare emergency shutdown, toxic gas response or complex isolation may need more frequent simulation or drill than a routine task. Changes to plant, procedure, alarm philosophy, staffing, contractor arrangements or emergency plan should trigger reassessment.

Erosion controls
Erosion routeHow it developsControl
Infrequent taskPeople forget steps and abnormal cues.Practice, simulation or supervised revalidation.
Procedure changeOld habits continue after change.Change briefing and reassessment.
Staff turnoverExperience leaves the organisation.Succession plan and knowledge capture.
AutomationPeople lose manual or diagnostic skill.Abnormal scenario practice.
Contractor rotationSite-specific knowledge becomes thin.Re-induction and task verification.
Normalisation of deviationWorkarounds become accepted.Supervision, audit and just-culture investigation.

Applied case

Fictional exercise: A control interface changes after the last task assessment.

Trigger

A changed interface can alter what the task requires.

Response

Choose assessment or learning that addresses the actual gap.

Test your decision

What should be reviewed?

  1. Only the age of the certificate.
  2. A universal refresher interval selected by the learner.
  3. Whether the assessed capability still covers the changed task and interface.
Compare the explanation

Whether the assessed capability still covers the changed task and interface.

Review follows the actual task basis and relevant triggers.

Open this interactive lesson →

LESSON 6

Look at the human task system

Avoid treating human factors as a synonym for error.

Process operators monitoring equipment from a UK industrial control room
Existing SHAREhub photographic illustration. The written fictional case supplies the condition and decision evidence.

Look at the human task system

Human factors examines how the job, person and organisation influence performance. Information layout, workload, tools, supervision and competing goals can shape a decision. Calling an event human error does not explain those relationships.

Start with a concrete task and examine what the person could see, understand and do. Keep evidence distinct from assumptions. Human-factors awareness does not mean every error is excused or every interface is defective; it means the response considers the conditions that make reliable action more or less achievable.

What does human factors mean in process operations?

Human factors in process operations applies job, individual and organisational factors to hazardous plant and safety-critical tasks.

In a process plant, the human factors question is not simply 'did the operator follow the rule?' It is: was the work set up so a competent person could succeed under the actual conditions? That means examining the task, the controls, the information available, the time pressure, the staffing, the noise, the lighting, the alarms, the permit arrangements, the supervision and the wider decisions that shaped the situation. HSE managing human failures

The topic is especially important because many process safety barriers rely on human performance. A person may need to recognise an alarm, diagnose a deviation, stop a pump, verify an isolation, test for gas, check a permit, open the correct valve, start an emergency shutdown, hand over plant status or challenge a risky production decision. If the task is badly designed, the barrier is weaker than the risk assessment claims.

AreaPlain-English meaningProcess safety example
Job factorsThe task, equipment, environment and information available to the person.Alarm screen layout, valve labels, access, lighting and procedure format. HSE managing human failures
Individual factorsCompetence, fatigue, experience, stress, health and familiarity with the task.New control-room operator responding to a rare trip scenario. HSE managing human failures
Organisational factorsLeadership, staffing, priorities, culture, resources and change control.Deferred maintenance, permit rush, shift cover and production pressure. HSE managing human failures
Human reliabilityHow likely people are to perform a safety-critical action correctly when needed.Manual response to high-level alarm before tank overfill. HSE managing human failures
Barrier assuranceEvidence that human-dependent controls can be relied on.Observed emergency drill, verified handover and closed alarm actions. HSE managing human failures

Applied case

Fictional exercise: A route error occurs during an interrupted handover with two similar identifiers.

Action

What the person did is part of the sequence.

Conditions

Why the action made sense or became likely needs evidence.

Test your decision

What should be examined?

  1. A certainty that the interface caused the event.
  2. The task, available information and organisational conditions alongside the action.
  3. Only a claim that the operator lacked care.
Compare the explanation

The task, available information and organisational conditions alongside the action.

Investigate supported relationships without replacing one assumption with another.

Open this interactive lesson →

LESSON 7

Examine coincident demands

Recognise workload and fatigue without diagnosing individuals.

Process operators monitoring equipment from a UK industrial control room. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Avoid / redesign: Remove needless manual response to tank level by redesigning transfer limits and route. Control the task: Segregate incorrect lineups and positively isolate incompatible transfer paths. Verify before release: Uncontrolled overfill path: hold.

Examine coincident demands

A task that is manageable alone can become difficult when alarms, calls and field work coincide. Consider the timing, complexity and resources needed for safety-critical actions. A staffing number by itself does not establish whether demands can be managed.

Fatigue can affect performance, but a course vignette cannot diagnose a person. Use the organisation’s reporting and fitness-for-work arrangements and examine work design as well as individual circumstances. Avoid prescribing a universal shift pattern or assuming motivation can overcome an unsustainable task arrangement.

How do workload and fatigue affect process operations?

Workload and fatigue can turn a normally manageable task into an error-prone task.

Overload occurs when there are too many tasks, alarms, permits, decisions or interruptions for the time and resources available. Underload can also be dangerous where monitoring is prolonged and uneventful. Fatigue can reduce attention, memory, decision quality and willingness to challenge unsafe conditions. HSE workload

Sites should assess workload during peaks, not just quiet periods. A control room may look adequate in normal operation but become unmanageable during start-up, trip recovery or multiple alarms. A supervisor may be competent but still unable to actively supervise if they are issuing permits, managing contractors, answering calls and covering absent staff at the same time.

ExampleHow risk increasesControl
Alarm flood during compressor tripCritical alarm is missed or response is delayed.Alarm rationalisation, priority rules and emergency response drills. HSE workload
Permit rush at shift startIssuer copies conditions or misses SIMOPS conflict.Permit staggering, permit coordinator and field verification. HSE workload
Extended turnaround shiftsFatigue affects isolation checks and handback quality.Fatigue risk assessment, shift limits and supervisor review. HSE workload
Single supervisor covering several jobsHigh-risk work is not actively monitored.Risk-based supervision plan and workload review. HSE workload
Quiet night monitoringLow stimulation reduces situation awareness.Task rotation, alarm design and fatigue controls. HSE workload

Applied case

Fictional exercise: One person must acknowledge an alarm while completing a separate field verification; the overlap has not been assessed.

Coincidence

Two acceptable tasks can conflict when required together.

Support

Review allocation and resources rather than assuming effort solves the conflict.

Test your decision

What is needed?

  1. Review the coincident critical demands, support and response arrangements.
  2. A demand to concentrate harder.
  3. A diagnosis based only on the vignette.
Compare the explanation

Review the coincident critical demands, support and response arrangements.

Workload review concerns the task system and evidence.

Open this interactive lesson →

LESSON 8

Make information usable

Connect alarm response to detection, understanding and action.

Process operators monitoring equipment from a UK industrial control room. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Change at source: Remove needless manual response to tank level by redesigning transfer limits and route. Make it observable: Uncontrolled overfill path: hold. Keep useful evidence: Were valves labelled, segregated, accessible and independently verified?

Make information usable

An alarm can help only if the relevant condition is detected, the message is understood and an effective action can be completed within the assessed arrangement. An alarm list is not proof that these steps are achievable.

Repeated or poorly prioritised signals can obscure what matters. Review the actual scenario, response procedure, interface and workload with competent specialists. Awareness does not set alarm thresholds or assign risk-reduction credit. The learner identifies whether the claimed response has a clear and evidenced basis.

How should alarms, displays and interfaces support operators?

Alarms and interfaces should help people understand plant state and choose the right response.

An alarm flood is a design and workload fault, not proof that the operator should simply concentrate harder. Prioritise alarm meaning, rate and consequence, then verify the independent high-level stop under the actual abnormal state. HSE alarm management HSE COMAH control systems

An alarm system is not a decoration; it is a safety-critical communication channel. Poor systems create nuisance alarms, alarm floods, unclear priorities, repeated acknowledgements without action and loss of trust. Operators then learn to silence alarms rather than diagnose them.

Interface design matters in the field as well as in control rooms. Similar valve handles, poor labels, confusing line numbers, inaccessible indicators, hidden drains and unclear mimic screens all increase error likelihood.

IssueGood practiceEvidence
Alarm priorityPriorities match consequence and response time.Alarm philosophy and rationalisation records. HSE alarm management
Operator actionEvery alarm has a clear response and escalation route.Alarm response manual and drill results. HSE alarm management
Alarm loadStanding alarms and nuisance alarms are reduced.Alarm performance dashboard and action tracker. HSE alarm management
Display usabilityCritical values, trends and limits are visible.Control-room review and operator feedback. HSE alarm management
Field labellingValves, drains and equipment are clear and consistent.Field walkdown and defect close-out. HSE alarm management

Applied case

Fictional exercise: A review credits an operator alarm response but gives no defined action or workload assessment.

Signal

Detection and annunciation are parts of the function.

Response

Understanding and achievable action complete the human task.

Test your decision

What is missing?

  1. Only a louder sound.
  2. An assumed independent barrier because the alarm has a name.
  3. A justified response arrangement connecting the signal to an achievable effective action.
Compare the explanation

A justified response arrangement connecting the signal to an achievable effective action.

A credited response needs more than the presence of a signal.

Open this interactive lesson →

LESSON 9

Test instructions against use

Recognise when a written step does not resolve a task difficulty.

Process operators monitoring equipment from a UK industrial control room. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Immediate action: Were valves labelled, segregated, accessible and independently verified? Procedure: Was the critical lineup step visible, current and usable during real transfer work? Alarm system: Was it trusted, prioritised and linked to a clear operator action?

Test instructions against use

A procedure should support the actual task, with usable sequence, identification and decision points. Examine whether users can find the information and distinguish normal operation from abnormal response. More pages are not automatically more helpful.

Involve relevant users in review without allowing informal edits to replace document control. If instructions and plant disagree, use the defined restriction and clarification route. A learner should not guess which version is correct or carry out a trial on live equipment to settle the difference.

How should procedures work in real process operations?

Procedures should support competent performance at the workface, especially where steps are safety critical.

A procedure that is technically correct but unusable is a weak control. It should be current, task-specific, written for the people using it, tested in the field, clear about critical steps and aligned with the plant as actually built. Safety-critical hold points should stand out. HSE procedures

Procedures should also say what to do when conditions do not match the plan. Many serious events occur because people press on when a valve is not where expected, a reading looks wrong, a permit condition cannot be met or an alarm behaves differently from the procedure.

Quality featureGood practiceWeak signal
User testedOperators and maintainers test it against real work.Procedure only reviewed in an office. HSE procedures
Critical steps visibleHold points and stop criteria are highlighted.Important warnings hidden in text. HSE procedures
Matches plantLine numbers, valve tags and equipment match field reality.Workers annotate unofficial corrections. HSE procedures
Abnormal guidanceExplains when to stop, escalate or revert to safe state.People improvise during upset conditions. HSE procedures
Review triggerUpdated after change, incident, alarm review or worker feedback.Only date changed at annual review. HSE procedures

Applied case

Fictional exercise: The instruction names an indicator that no longer matches the field label.

Usable

Information must support the decision at the point of work.

Controlled

Changes to instructions need the responsible review.

Test your decision

What is sound?

  1. Test both possibilities during live transfer.
  2. Raise the mismatch and use the defined task restriction pending clarification.
  3. Choose whichever name seems familiar.
Compare the explanation

Raise the mismatch and use the defined task restriction pending clarification.

A mismatch needs controlled resolution, not improvisation.

Open this interactive lesson →

LESSON 10

Prepare for infrequent conditions

Assess rare tasks without creating the hazard.

2D teaching diagram: Make critical work manageable for people
Existing SHAREhub 2D teaching schematic. Use alongside the explanation and fictional case in this lesson.

Prepare for infrequent conditions

An abnormal situation may demand a different sequence, team and decision boundary from routine operation. Infrequency can make recall and coordination harder. Appropriate practice can examine interpretation and communication without reproducing a dangerous event.

Use a planned, safe method with competent assessment and clear limits. Success in a tabletop exercise is useful evidence within its scope, not proof that every real emergency will be controlled. Feed identified gaps into procedures, competence and readiness arrangements rather than merely recording that an exercise took place.

How should decision making under abnormal conditions be managed?

Abnormal conditions need pre-planned decision rights, clear triggers and practiced responses.

During abnormal conditions, people may be dealing with uncertainty, incomplete information, alarms, time pressure and competing goals. A good organisation decides in advance who can stop, who can restart, who authorises deviation from normal limits and what evidence is needed before plant is returned to service. HSE COMAH control room design

Decision aids should be simple. If the operator has to read a long manual while alarms are sounding, the design has already failed. Critical actions should be trained, rehearsed and backed by engineered protection where the consequence is high.

Decision pointGood controlEvidence
Continue or stopDefined safe operating limits and stop criteria.Safe operating envelope and operator briefing. HSE COMAH control room design
Restart after tripRestart only after checks and authority are complete.Restart checklist and authorisation log. HSE COMAH control room design
Bypass or inhibitFormal approval, time limit and compensating controls.Bypass register and daily review. HSE COMAH control room design
Emergency escalationClear trigger for site emergency response.Drill record and call-out test. HSE COMAH control room design
Shift handover during upsetFace-to-face structured handover with readback.Handover log and supervisor sign-off. HSE COMAH control room design

Applied case

Fictional exercise: A shutdown decision is rarely used and has changed since the last exercise.

Practice

A planned exercise can test decisions and coordination.

Limit

Its result remains bounded by the conditions tested.

Test your decision

What is appropriate?

  1. Review and practise the relevant decisions safely within the competence and readiness arrangements.
  2. Create an uncontrolled live upset.
  3. Assume routine-task experience covers every abnormal event.
Compare the explanation

Review and practise the relevant decisions safely within the competence and readiness arrangements.

Rare-task preparation needs a safe and task-relevant basis.

Open this interactive lesson →

LESSON 11

Check contracted competence and interfaces

Avoid equating supplier approval with task readiness.

Process operators monitoring equipment from a UK industrial control room. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Avoid / redesign: Avoid a nonessential transfer or overfill-prone routing. Control the task: Specify an independent high-high level trip, closure time and containment capacity against the overfill scenario; document alarm set point and safe transfer rate. Verify before release: Planning lead verifies need; hold task if safe route is unknown.

Check contracted competence and interfaces

A contractor’s qualifications and experience are important, but the specific scope, local hazards and authority boundaries still need agreement. Check who supervises, who controls process conditions and who accepts the completed work.

The contractor also needs a route to report discoveries and limitations. Do not use a supplier’s approved status as proof that every assigned individual is ready for every task. Equally, do not duplicate irrelevant training while overlooking the local process information that makes the work safe and effective.

How should contractor competence be managed?

Contractor competence should be specified, verified, supervised and reviewed wherever contractor work can affect major accident barriers.

Contractor competence is not proven by a company brochure, prequalification badge or generic training certificate. The host organisation needs to define the site-specific hazards, interfaces, permit rules, isolations, emergency actions and supervision required for the task.

Contractors may perform intrusive maintenance, tank cleaning, scaffold erection, inspection, lifting, electrical work, hot work or specialist engineering. Each can affect containment, ignition control, emergency systems or access to safety-critical equipment.

Contractor competence controls
StageWhat to checkEvidence
PrequalificationRelevant experience, supervision, training and incident history.Approved supplier record.
Task planningHazard awareness, method, interfaces and permit requirements.RAMS review and pre-job meeting.
Site inductionLocal hazards, alarms, emergency routes and reporting.Induction and understanding check.
SupervisionHost oversight matched to risk and contractor familiarity.Field checks and permit audits.
Performance reviewLearning from defects, near misses and work quality.Post-job review and supplier feedback.

Applied case

Fictional exercise: An approved supplier sends a substitute worker whose task-specific capability is not established.

Organisation

Supplier approval concerns a defined organisational scope.

Individual

Assigned people still need the relevant capability and information.

Test your decision

What should be checked?

  1. Only the supplier’s logo.
  2. Automatic approval from the supplier list.
  3. The person’s relevant competence, supervision and local interface before allocation.
Compare the explanation

The person’s relevant competence, supervision and local interface before allocation.

Supplier status does not establish individual task readiness.

Open this interactive lesson →

LESSON 12

Assemble a competence assurance decision

Integrate role, assessment, authority and work conditions.

Process operators monitoring equipment from a UK industrial control room. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Change at source: Avoid a nonessential transfer or overfill-prone routing. Make it observable: Planning lead verifies need; hold task if safe route is unknown. Keep useful evidence: Major accident hazard register, bowties and competence matrix.

Assemble a competence assurance decision

A useful competence record connects the role to tasks, assessment evidence, authorisation scope and review triggers. It should also identify supervision and task conditions that make performance achievable. A certificate folder alone cannot answer every allocation decision.

For the fictional case, separate established capability from unresolved questions. Identify the responsible assessor or task owner and preserve restrictions while the gap is addressed. The output is a learning and assurance plan, not a new real authorisation or a claim that the course has qualified a process specialist.

What indicators show whether competence arrangements are healthy?

Indicators should show whether critical-role competence is current, tested, supervised and improving before a serious event exposes a weakness.

HSG254-style thinking is useful here: choose leading and lagging indicators for the barriers that matter. A training-completion percentage may be useful, but it should not be the only measure. Better indicators also include failed assessments, overdue reassessments, temporary authorisations, critical-role vacancies, contractor findings, permit errors, alarm-response delays and repeated procedural deviations.

Competence indicators
IndicatorTypeWhat it may reveal
Overdue critical-role reassessmentsLeadingCompetence assurance is drifting.
Temporary authorisations in critical rolesLeadingStaffing pressure may be weakening controls.
Failed or marginal assessmentsLeadingTraining or supervision may need improvement.
Permit errors involving critical workLagging/leadingAuthorisation and briefing may be weak.
Abnormal event response delaysLaggingScenario training or alarm management may be inadequate.
Contractor non-conformancesLagging/leadingPrequalification, induction or supervision may be weak.

Applied case

Fictional exercise: The record shows routine-task assessment, but the changed abnormal-response task and local authority remain unconfirmed.

Retain

Do not discard relevant demonstrated capability.

Resolve

Do not extend it silently beyond its assessed and authorised scope.

Test your decision

Which conclusion is justified?

  1. All prior evidence has no value.
  2. Routine evidence is useful; the changed task and authority need responsible review.
  3. The person is approved for all tasks.
Compare the explanation

Routine evidence is useful; the changed task and authority need responsible review.

Evidence is retained within scope while gaps remain explicit.

Open this interactive lesson →