Crownway Fuels

SHAREhub · Company management system · v1.0

← All Crownway resources

Work at height and access equipment policy

CWF-POL-HEIGHT · Completed fictional example · Owner role: Engineering and asset integrity manager

Fictional arrangement or blank working master. No actual approval, site authorisation or completed evidence is supplied.

Work at height and access equipment policy

Topical health and safety policy

Crownway Fuels Ltd

Business nameCrownway Fuels LtdEmployeesApproximately 200
IndustryPetrol and diesel forecourts and convenience retailOperating locationsTen English petrol/diesel forecourts and convenience shops, HQ and mobile support. The additional bulk establishment is a separate illustrative scenario. Inventory, regulatory applicability, permissions and site-specific acceptance are unresolved.
Policy referenceCWF-POL-HEIGHTStatusIn progress — confirm controlled issue
OwnerEngineering and asset integrity managerApproval authorityManaging director and board
Issue version1.0Business areaWork at height and access equipment
Effective dateNot recordedNext reviewNot recorded
JurisdictionEngland baseline. GB duties and conditional national overlays retain their own scope. Northern Ireland is outside this example.AudienceEngineering and asset integrity manager; Health safety and environmental lead; Site manager and shift supervisor; Fuel operator and retail colleague; Contractor performing authority

Controlled document. Confirm the current issue and authorised approval before use.

Contents

Select a section to open it. ISO 45001 references show the clause alignment.

Business context

1 Policy statement ISO 5.1, 5.2, 5.4, 10.3

2 Purpose ISO 4.1, 6.1, 6.2

3 Scope ISO 4.3

4 Definitions and abbreviations ISO 7.4, 7.5

5 Legal regulatory and other requirements ISO 6.1.3

6 Roles responsibilities and accountabilities ISO 5.1, 5.3

7 Worker consultation and participation ISO 5.4

8 Hazard identification and risk assessment ISO 6.1.2, 6.1.4

9 Control measures and safe systems of work ISO 8.1, 8.1.2

10 Competence training and awareness ISO 7.2, 7.3

11 Communication requirements ISO 7.4

12 Operational requirements ISO 8.1

13 Emergency preparedness and response ISO 8.2

14 Incident reporting investigation and learning ISO 10.2

15 Monitoring measurement and performance evaluation ISO 9.1

16 Audit and assurance ISO 9.2

17 Management review ISO 9.3

18 Objectives targets and improvement plan ISO 6.2

19 Management of change ISO 8.1.3

20 Procurement contractors and suppliers ISO 8.1.4

21 Records and documented information ISO 7.5

22 Nonconformance and corrective action ISO 10.2

23 Continual improvement ISO 10.3

24 Policy review and approval ISO 5.2, 7.5

Appendix A ISO 45001 clause mapping

Appendix B Review and source record

Business context

Return to contents

Activities and scope: Work at height and access equipment at applicable sites

Significant risks and interfaces: Canopy, roof, tanker-top and sign maintenance can expose staff or contractors to falls and falling objects above public areas.

Existing arrangements: Use the linked Crownway procedure and supporting records. This example contains no operational results or approved issue.

Other requirements: Determine actual permission, design, manufacturer and contract requirements before adoption.

Relevant learning: No actual Crownway incident history supplied. The worked decision in the linked procedure is invented.

Confirm competent review and organisational approval before issue. Tailor this policy to the actual business, activities, workers, locations and jurisdiction. Verify applicable legal duties, resources, control arrangements and evidence before issue. ISO 45001 clause references are an alignment guide; they do not establish certification or compliance. Unconfirmed arrangements must be resolved before the policy is used.

1 Policy statement

Return to contents

ISO 45001 alignment: 5.1, 5.2, 5.4, 10.3

We prevent work-related injury and ill health and protect people and the environment through proportionate control of work at height and access equipment. The board provides resources, supports consultation and protects the right to stop unsafe work. Stop for absent edge protection, unsuitable access, unsafe weather, fragile surface uncertainty, uncontrolled people below or missing rescue provision.

Implementation and effectiveness evidence

Board commitments and resourcing decisions; actual stop and escalation evidence.

SHARE guidance: working at height

2 Purpose

Return to contents

ISO 45001 alignment: 4.1, 6.1, 6.2

This policy establishes company direction for work at height and access equipment. Canopy, roof, tanker-top and sign maintenance can expose staff or contractors to falls and falling objects above public areas. The linked procedure translates these commitments into practical preparation, operating, verification and handback decisions.

Implementation and effectiveness evidence

Defined objective, task scope and links to practical arrangements.

SHARE guidance: working at height

3 Scope

Return to contents

ISO 45001 alignment: 4.3

BULK; HQ; RETAIL. Apply where the site/activity/hazard is present; confirm in the site applicability assessment. Apply only to the established activities present at the actual location. Ten English petrol/diesel forecourts and convenience shops, HQ and mobile support. The additional bulk establishment is a separate illustrative scenario. Inventory, regulatory applicability, permissions and site-specific acceptance are unresolved. A bulk-scenario requirement is not a finding about an existing forecourt.

Implementation and effectiveness evidence

Site profile, operator, activity and applicability decision with unresolved limits.

SHARE guidance: working at height

4 Definitions and abbreviations

Return to contents

ISO 45001 alignment: 7.4, 7.5

A critical control prevents or limits a serious harm scenario. An impairment is an unavailable or unreliable safeguard. Verification tests evidence against defined criteria. An action marked implemented still needs effectiveness review. Work release is the separate decision by an authorised person for a defined task.

Implementation and effectiveness evidence

Shared definitions and a briefing demonstrating understanding.

SHARE guidance: working at height

5 Legal regulatory and other requirements

Return to contents

ISO 45001 alignment: 6.1.3

The HSE lead and relevant specialist check the actual dutyholder, jurisdiction, activity and trigger. Direct duties, permit or certificate requirements, ACOPs, guidance, standards and company rules are recorded distinctly. Illustrative company control supporting the duties and applicability conditions in the linked legal register. No register entry grants a permission.

Implementation and effectiveness evidence

Current legal and permissions register, dutyholder decision and dated primary sources.

SHARE guidance: working at height

6 Roles responsibilities and accountabilities

Return to contents

ISO 45001 alignment: 5.1, 5.3

Engineering and asset integrity manager owns this policy and its evidence. Operations coordinates actual work and site interfaces. Engineering decides technical fitness within competence. The board resolves resources and major risk decisions. Workers report defects and stop unsafe work. Appointed specialists advise within their scope; legal dutyholders retain their duties.

Implementation and effectiveness evidence

Named appointments, competence, deputies and authority limits.

SHARE guidance: working at height

7 Worker consultation and participation

Return to contents

ISO 45001 alignment: 5.4

Consult the people who perform and are affected by the work, including night staff, mobile staff, contractors and recognised representatives. Record concerns before the decision, explain the response and test understanding. Provide accessible ways to report uncertainty or challenge an unsafe arrangement without detriment.

Implementation and effectiveness evidence

Consultation record, workforce concerns and feedback to originators.

SHARE guidance: working at height

8 Hazard identification and risk assessment

Return to contents

ISO 45001 alignment: 6.1.2, 6.1.4

Avoid work at height where practicable, then prevent falls and minimise consequences through the proper hierarchy. Assess the surface, access, edges, fragile materials, people below and task duration. Record uncertainties, credible consequences and people affected. Link the organisational risk to the relevant task and specialist assessments. A favourable rating cannot displace a duty or a failed critical control.

Implementation and effectiveness evidence

Assessment, worker input, assumptions and control selection rationale.

SHARE guidance: working at height

9 Control measures and safe systems of work

Return to contents

ISO 45001 alignment: 8.1, 8.1.2

Avoid height work, select collective protection before personal fall protection, verify access equipment and weather, segregate below and plan rescue for the chosen method. Commission competent specialists for fragile roofs and tanker access. Select suitable equipment, competent people, inspections and rescue arrangements. Coordinate fuel-site ignition and traffic risks as well as the fall hazard. Do not use a ladder solely because it is immediately available.

Implementation and effectiveness evidence

Actual control implementation and task-specific evidence of protective function.

SHARE guidance: working at height

10 Competence training and awareness

Return to contents

ISO 45001 alignment: 7.2, 7.3

Define the competence required for work at height and access equipment and check practical capability, experience, language and supervision. Keep an explicit authorised scope and reassess after change or failure. Awareness-course completion is evidence of learning only, not practical authority to carry out the task.

Implementation and effectiveness evidence

Task competence evaluation, supervision and restricted authorisation.

SHARE guidance: working at height

11 Communication requirements

Return to contents

ISO 45001 alignment: 7.4

Brief current instructions, limits, precautions and stop conditions before the work. Use a two-way understanding check and hand over impairments between shifts and parties. The document controller withdraws superseded instructions while preserving the history and its evidence.

Implementation and effectiveness evidence

Current issue distribution, briefing, understanding and shift handover.

SHARE guidance: working at height

12 Operational requirements

Return to contents

ISO 45001 alignment: 8.1

Avoid work at height where practicable, then prevent falls and minimise consequences through the proper hierarchy. Assess the surface, access, edges, fragile materials, people below and task duration. Select suitable equipment, competent people, inspections and rescue arrangements. Coordinate fuel-site ignition and traffic risks as well as the fall hazard. Do not use a ladder solely because it is immediately available. Close the activity through the linked handback and verification controls; record the safe final state and unresolved restrictions.

Implementation and effectiveness evidence

Preparation, operating and handback records linked to the actual work.

SHARE guidance: working at height

13 Emergency preparedness and response

Return to contents

ISO 45001 alignment: 8.2

Raise the alarm, protect people and summon emergency assistance promptly when required. Withdraw and prevent re-entry. Only trained and authorised people attempt isolation, containment or rescue within a safe method. Use the site-specific emergency plan and provide responders accurate substance and access information.

Implementation and effectiveness evidence

Site emergency arrangements, cover, exercises and unresolved readiness actions.

SHARE guidance: working at height

14 Incident reporting investigation and learning

Return to contents

ISO 45001 alignment: 10.2

Report incidents, near misses, occupational-health concerns and barrier failures promptly. Preserve facts after making the area safe. The HSE lead checks applicable RIDDOR, COMAH and environmental reporting criteria and deadlines separately. Investigation examines evidence and organisational causes, not only individual actions.

Implementation and effectiveness evidence

Facts, reporting decision, genuine submission evidence where required and investigation.

SHARE guidance: working at height

15 Monitoring measurement and performance evaluation

Return to contents

ISO 45001 alignment: 9.1

The supervisor checks the actual setup, environment and equipment before use and after changes. Stop for conditions outside the accepted method or when collective protection, equipment condition or recovery arrangements are uncertain. Use evidence from actual work, not merely a signed form. Keep missing, failed and overdue safeguards visible and escalate promptly.

Implementation and effectiveness evidence

Defined indicators, source records, exceptions and field verification.

SHARE guidance: working at height

16 Audit and assurance

Return to contents

ISO 45001 alignment: 9.2

A competent reviewer with appropriate independence samples the applicable duty, procedure, worksite and evidence. State the sample and limits, challenge inconsistent accounts and test repeat findings. A document audit or external certificate alone does not establish effective control across every site.

Implementation and effectiveness evidence

Audit criteria, sample, independence limits, findings and verification.

SHARE guidance: working at height

17 Management review

Return to contents

ISO 45001 alignment: 9.3

The board reviews critical failures, exposure concerns, overdue actions, legal change, worker feedback, audit findings and resource constraints. Record decisions, owners, dates and restrictions. Serious control failures are escalated immediately rather than waiting for a planned meeting.

Implementation and effectiveness evidence

Management review decisions, resources, action ownership and follow-through.

SHARE guidance: working at height

18 Objectives targets and improvement plan

Return to contents

ISO 45001 alignment: 6.2

The policy owner sets measurable improvements from the actual control gaps. Each objective has a baseline, accountable role, resources, milestones and an effectiveness test. Success means the intended control functions reliably in the defined scope; production or checklist totals alone are insufficient.

Implementation and effectiveness evidence

Baseline, milestones and defined effectiveness results.

SHARE guidance: working at height

19 Management of change

Return to contents

ISO 45001 alignment: 8.1.3

Screen changes to equipment, product, layout, staffing, software, contractor arrangements and operating method before implementation. Obtain technical and regulatory review, update information, brief people and verify readiness. Temporary changes have an owner, expiry, restoration plan and review before extension.

Implementation and effectiveness evidence

Change assessment, permission review, readiness and temporary-change expiry.

SHARE guidance: working at height

20 Procurement contractors and suppliers

Return to contents

ISO 45001 alignment: 8.1.4

Specify the competence, compatibility, safety function, information and lifecycle support required before purchase or appointment. Coordinate contractor hazards, permits, isolations and simultaneous work. Reject unauthorised substitutions and verify completed work and technical handback before operational return.

Implementation and effectiveness evidence

Supplier specification, capability checks, work coordination and handback.

SHARE guidance: working at height

21 Records and documented information

Return to contents

ISO 45001 alignment: 7.5

Retain the permanent document and record references, current revision, actual scope, competent author, dates, findings, restrictions, actions and supporting evidence. Approved content, competent owner, briefing and field verification appropriate to the document. Apply an approved record-specific retention rule and legal holds. Restrict personal and clinical information to authorised access.

Implementation and effectiveness evidence

Controlled record, evidence reference, access and applicable retention decision.

SHARE guidance: working at height

22 Nonconformance and corrective action

Return to contents

ISO 45001 alignment: 10.2

Make the affected area safe, record the failed requirement and apply interim restrictions. Assign an owner and due date without concealing delay by resetting it. Record implementation separately from competent verification. Reopen an action when the control is ineffective or assumptions change.

Implementation and effectiveness evidence

Containment, owner, due date, implementation and separate effectiveness evidence.

SHARE guidance: working at height

23 Continual improvement

Return to contents

ISO 45001 alignment: 10.3

Review repeated failures and transferable learning across the ten forecourts, HQ and mobile work. Test whether the change improves the actual task and creates any new risk. Maintain specialist and bulk-scenario boundaries when sharing an improvement.

Implementation and effectiveness evidence

Cross-site learning, tested improvement and remaining limitations.

SHARE guidance: working at height

24 Policy review and approval

Return to contents

ISO 45001 alignment: 5.2, 7.5

Prepared as a fictional Crownway example on 10 November 2026. Before first use and after change, incident, defective control or assurance finding; risk-based scheduled review. The owner resolves competent review comments and the board records any genuine controlled issue separately. Approval, signatures and effective dates are intentionally absent from this example. ISO references are alignment aids and do not establish certification.

Implementation and effectiveness evidence

Technical review, resolved comments, genuine approval and issue history when adopted.

SHARE guidance: working at height

Appendix A ISO 45001 clause mapping

Return to contents

Clause references follow the supplied SHARE topical policy framework. This mapping is an alignment aid and does not reproduce the standard or establish certification.

Policy sectionISO 45001 clauses
1 Policy statement5.1, 5.2, 5.4, 10.3
2 Purpose4.1, 6.1, 6.2
3 Scope4.3
4 Definitions and abbreviations7.4, 7.5
5 Legal regulatory and other requirements6.1.3
6 Roles responsibilities and accountabilities5.1, 5.3
7 Worker consultation and participation5.4
8 Hazard identification and risk assessment6.1.2, 6.1.4
9 Control measures and safe systems of work8.1, 8.1.2
10 Competence training and awareness7.2, 7.3
11 Communication requirements7.4
12 Operational requirements8.1
13 Emergency preparedness and response8.2
14 Incident reporting investigation and learning10.2
15 Monitoring measurement and performance evaluation9.1
16 Audit and assurance9.2
17 Management review9.3
18 Objectives targets and improvement plan6.2
19 Management of change8.1.3
20 Procurement contractors and suppliers8.1.4
21 Records and documented information7.5
22 Nonconformance and corrective action10.2
23 Continual improvement10.3
24 Policy review and approval5.2, 7.5

Appendix B Review and source record

Return to contents

Source and review record

Original Crownway company example prepared 10 November 2026

Completed fictional policy. Approval and effective date remain blank. Current primary guidance was checked for the described scope; site-specific applicability and technical acceptance remain separate.

Reviewer confirmation: Pending

Questions to resolve:

Confirm the actual site and activity scope, named role holders and deputies.

Resolve applicable permissions, technical limits and evidence gaps before controlled issue.

Research source versions

Working at Height

Supporting Knowledge Hub guidance

Updated: 2026-11-10 source checked

Knowledge Hub data SHA-256: a6f1f7063933055f7f268f2ddd63034db49335dc1686ee6aa9c5a155e66324f1

https://www.sharehub.ltd/knowledge-hub/working-at-height.html

Framework: supplied SHARE HSE Topical Policy Template. Current standard and policy guidance:

ISO 45001 overview | HSE policy guidance

Primary references: work at height

Related resources

Primary guidance