Full public teaching and readers are free without an account. A free learner account is required for saved LMS progress and recorded assessment. Completion and any course-completion certificate depend on the configured LMS conditions. Open the course overview.
Lesson 1
Separate hot contact from a developing reaction hazard
Recognise that normal heat, abnormal heat generation and their protective systems require different evidence.
Photorealistic illustrative UK workplace scene. Review checks: Setting: A fictional chemical process adds material to a reactor within an assessed operating envelope. Act: The competent team considers heat generation, removal, mixing, conversion and hidden accumulation using the actual reaction evidence. Hold / review: Use the assessed abnormal-response procedure; do not improvise feed, cooling, quench or relief settings.
Separate hot contact from a developing reaction hazard
Hot tooling can burn someone even while the process is otherwise operating as intended. A developing reaction hazard raises a different question: is heat being generated faster than the assessed system can remove or control it? Do not collapse these mechanisms into a single instruction to wear gloves. The immediate exposure and the process condition need separate controls.
The native model contains a nominal 180°C clue. It is an exercise condition, not a validated operating target, safe touch temperature or recipe for any resin. Actual limits and responses depend on the formulation, quantity, equipment and engineered safeguards. A learner should not calculate an emergency action or alter a setpoint from this course.
Unexpected temperature behaviour, cooling faults or alarm discrepancies must be handled through the assessed operating and emergency arrangements. Keep unauthorised interventions prevented and communicate the actual indications and changes. An apparently normal display cannot overrule contradictory evidence without a competent check of what the system is measuring.
For practice, sort the information into contact protection, process stability and response capability. Identify what would make each claim credible. The fact that an operator can avoid touching the tool does not establish control of an abnormal reaction; equally, a process report does not remove a hot-surface exposure during access. Maintain the relevant safe state and escalate uncertainty to the competent process owner. This course develops recognition and evidence questions, not process-design or emergency-control competence.
How should reaction hazards be managed through the lifecycle?
Carry reaction knowledge from laboratory concept through design, commissioning, batches, cleaning, maintenance, change and emergency response.
At development stage, identify intended and unintended reactions, heat and gas release, decomposition and contaminant effects. A small-scale result may not transfer to a larger vessel because heat generation grows with volume while heat removal depends on surface area and equipment. Commissioning confirms the installed cooling, agitation, controls, relief and emergency arrangements against the design basis.
Who checks the reaction basis at each stage
Stage
Decision and evidence
Development and scale-up
Chemist and engineer select competent tests, document heat/gas and uncertainty, then approve the scale and safe envelope before larger trials.
Design and commissioning
Process and relief specialists define credible upsets, safeguard performance and discharge destination; commissioning proves installed functions before hazardous charge.
Operation and cleaning
Operator follows batch sequence and hold points; supervisor checks trends, deviations, residues, cleaning chemistry and waste route.
Maintenance and change
Maintainer proves safe isolation and hand-back; process owner reviews recipe, supplier, concentration, batch size, software and equipment changes before restart.
Emergency and recovery
Incident lead applies the site scenario plan and keeps people clear; competent team reviews damage and barrier restoration before authorising return to service.
A valve left partly closed after maintenance, a new supplier impurity or a shared drain can undo a good laboratory study. Each lifecycle handover needs a named owner and evidence, not only a signed form.
What are practical thermal stop triggers?
Thermal work should stop or change when symptoms, control failure or environmental change makes the plan unsafe.
Stop triggers are useful because heat and cold impairment can affect judgement. Workers may not recognise deterioration in themselves.
Briefings should make it acceptable to pause work for dizziness, shivering, numbness, failed ventilation, lack of water, soaked clothing, broken heating or unexpected weather. Provide first aid for symptoms; confusion or poor coordination during hot work, or confusion, slurred speech or slow breathing after cold exposure, means call 999 immediately before any task review.
Trigger
Immediate action
Review
Dizziness, confusion or collapse
Stop, give first aid and stay with the person. Confusion, poor coordination or collapse in heat: call 999 immediately; do not wait 30 minutes.
Care first; account for crew, then investigate heat controls before restart.
Shivering, numbness or poor dexterity
Move to shelter, remove wet clothing and get first aid. Suspected frostbite needs medical help; confusion, slurred speech or slow breathing after cold exposure: call 999 now.
Do not wait for a thermometer; review cold controls only after care is underway.
PPE being removed unsafely
Stop and reassess heat/PPE compatibility.
PPE and task redesign.
Ventilation/cooling failure
Pause heat-generating work.
Engineering repair.
No water or warm recovery area
Stop until welfare is restored.
Welfare assurance.
Weather shift
Re-brief and revise controls.
Dynamic review.
Applied case
The displayed temperature appears ordinary, but the trend and cooling indication have changed.
Decision and explanation
Treat the conflicting process evidence through the assessed response, while retaining separate hot-contact controls.
Correct decision: Treat the conflicting process evidence through the assessed response, while retaining separate hot-contact controls. Recognise that normal heat, abnormal heat generation and their protective systems require different evidence.
Lesson 2
Verify what is being mixed before relying on the process basis
Chemical hazard pictograms · examples and checksOptional reference · all nine symbols · does not change assessment requirements
READ THE LABEL · UNDERSTAND THE TASK
Recognise the symbol. Read the full label. Assess the actual task.
Examples illustrate possible uses of a symbol, not the classification of every formulation. A product can carry several pictograms. Check its current label, hazard statements and matching safety data sheet (SDS).
Resins: confirm every component, the approved process basis and the product’s stability information.
CLP/GHS hazard pictograms: meanings and illustrative examples
Pictogram and hazard
What it can mean
Example and question before work
ExplosiveGHS01
Explosion, blast or projection hazards; also certain self-reactive substances and organic peroxides.
Example: Certain fireworks or reactive chemical products.Ask: Does the authorised task account for impact, heat and the product’s stability limits?
FlammableGHS02
Can ignite; also used for certain self-heating, pyrophoric or water-reactive hazards.
Example: Petrol or some solvent-based products.Ask: What could release vapour or ignite it during this task, including nearby work?
OxidisingGHS03
Can cause or intensify fire; some strong oxidisers present an explosion hazard.
Example: Oxygen or certain oxidising chemicals.Ask: What incompatible materials and contamination must the assessed storage and connection keep apart?
Gas under pressureGHS04
Pressurised gas may burst if heated; refrigerated gas can cause cold burns.
Example: Compressed-gas cylinders.Ask: Have the gas identity, cylinder, connection and pressure or temperature hazards been checked?
CorrosiveGHS05
May damage metals, cause severe skin burns or cause serious eye damage; read the stated hazard.
Example: Certain drain cleaners, acids or alkalis.Ask: Which contact and splash routes must be prevented in this actual handling or dilution task?
Acute toxicityGHS06
Can be toxic or fatal after short exposure through the stated route.
Example: Methanol or certain pesticide products.Ask: Which exposure routes and emergency arrangements does this product’s information identify?
Harmful / irritantGHS07
May indicate harmful acute toxicity, irritation, skin sensitisation, drowsiness or dizziness; also ozone-layer hazards.
Example: Some detergents or cleaning products.Ask: What do the hazard statements say? Do not dismiss this as a harmless or mild product.
Serious health hazardGHS08
Can indicate cancer, genetic or reproductive harm, organ damage, respiratory sensitisation or aspiration hazard.
Example: Petrol or some sensitising chemical products.Ask: Which particular health effect is stated, and how does the task prevent the relevant exposure?
Hazardous to the environmentGHS09
Hazardous to aquatic life, potentially with long-lasting effects.
Example: Certain pesticides, biocides or fuels.Ask: How will the assessed arrangements prevent release to drains, water or soil?
Read beyond the picture · Open a prompt to compare the explanation.
Is the exclamation mark the same as the chest-starburst symbol?
No. The two symbols communicate different groups of hazards. Read the actual hazard statements: skin sensitisation and respiratory sensitisation are not interchangeable, and neither symbol specifies the complete task controls.
Does a bottle with no pictogram prove the task is safe?
No. Work may generate hazardous dust, fume or mist, and exposure depends on the task. Resolve missing or conflicting identification before use. A pictogram is not a compatibility chart or a complete workplace risk assessment.
Which information turns recognition into a useful work decision?
Match the product and SDS revision. Read the hazard statements and relevant SDS sections for handling, storage, exposure control, emergencies and reactivity together. Then check the actual task assessment and controls. A safety data sheet is not itself a COSHH assessment.
Fisher Scientific UK · BP2618 range · CAS 67-63-0 Revision 19 · 13 October 2023
This learning example refers to the identified supplier edition. It is not a replacement SDS or confirmation that this is the latest sheet for a product you hold. Obtain the current matching supplier SDS before real use.
Below is SHARE’s learning annotation, not a rebranded supplier document or a complete safety data sheet.
Identity
Propan-2-ol / isopropanol; the referenced sheet identifies a laboratory-grade product.
Section 2 signals
Danger; flame and exclamation-mark pictograms. H225, H319 and H336 identify flammability, eye irritation and possible drowsiness/dizziness.
Section 3 composition
The referenced sheet lists isopropyl alcohol above 95% by weight.
Section 8 decision
Engineering measures and several glove-material options appear. Check the complete conditions; no single glove or respirator is selected by this lesson.
Section 9 example
A 12°C closed-cup flash point is listed. This is product data, not a workplace exposure reading or an automatic safe-temperature limit.
Explore every section
1. Identification
Match the product, supplier, intended use and emergency contact to the actual container. A familiar chemical name alone may not identify a formulation.
2. Hazards identification
Read classification, pictograms, signal word and hazard/precautionary statements together. Identify the routes and outcomes the task must prevent.
3. Composition / ingredients
Check concentration and relevant ingredients. A diluted mixture, hardener or changed formulation may need different information and assessment.
4. First-aid measures
Prepare product-specific first-aid arrangements and ready access to the full sheet. Do not replace the workplace emergency procedure with a memory exercise.
5. Firefighting measures
Provide the relevant information to the site fire-planning route. An SDS does not authorise an untrained worker to fight a chemical fire.
6. Accidental release
Plan who raises the alarm, isolates the area and deals with a spill within their training. Confirm available equipment and the boundary for specialist help.
7. Handling and storage
Translate the supplier conditions into the actual transfer, storage, access and housekeeping method. Consider other work and incompatible neighbours.
8. Exposure controls / PPE
Read exposure limits, engineering controls and residual PPE together. Check jurisdiction, units and averaging period. Verify control performance and exact glove/RPE suitability.
9. Physical / chemical properties
Consider volatility, flash point, state and other relevant properties at the actual temperature and method. Odour is not a reliable exposure measurement.
10. Stability / reactivity
Identify incompatible materials, conditions to avoid and possible decomposition. Check the whole process and waste stream, not just separate containers.
11. Toxicological information
Connect the health effects to possible inhalation, skin, eye and ingestion exposure. Use competent advice where specialist interpretation is needed.
12. Ecological information
Plan to prevent environmental release, including drains and water. Lack of a fish/tree symbol does not grant permission to discharge.
13. Disposal considerations
Specify the responsible waste route for the product, contaminated materials and containers. Do not assume evaporation or dilution is an acceptable disposal method.
14. Transport information
Check transport classification through the relevant competent route. Supply pictograms and transport labels have different functions.
15. Regulatory information
Identify relevant restrictions and market scope, then check workplace duties separately. A regulatory entry is not a completed COSHH assessment.
16. Other information
Check revision history, abbreviations and supporting statements. Trace material changes into the assessment, instructions, storage and briefing.
Worked COSHH application · fictional laboratory proposal
Define the proposed use
Fictional laboratory task: wipe small parts for 10 minutes twice per shift, using a proposed 50mL working quantity at ambient temperature. Record the exact product, method, location, people and frequency. These are exercise assumptions, not authorised operating limits.
Find the exposure and application differences
Compare a controlled dispensing/wiping proposal with spraying the same liquid over an open surface near other work. Spray, surface area, ventilation, duration, splashes and nearby people change the assessment even though the SDS is unchanged. Confirm the proposed use is suitable.
Work through the control hierarchy
First ask whether the task can avoid the chemical or use a verified safer method. If it remains necessary, assess release prevention, suitable dispensing, enclosure or ventilation before residual PPE. Do not invent a dilution or declare a small quantity safe.
Specify and verify the real controls
Use sections 7–10 together with competent task assessment. Identify ventilation performance, compatible equipment and the exact glove selection/breakthrough evidence for the job. Consider fire and explosion controls alongside health exposure. Do not copy a generic PPE line and call the work controlled.
Plan the whole job
Include setup, transfer, use, cleaning, storage, waste, maintenance and foreseeable upset. Identify who is exposed, who owns each action, training, first aid, spill arrangements and the separate emergency response boundary.
Record, brief and review
Record significant findings, remaining actions and evidence needed before release. Check controls in use. Reassess for changed product, concentration, quantity, temperature, spraying, location, equipment, symptoms, incidents or new supplier information.
Worked decision: HOLD the proposed task until the matching product/use information, exposure and ignition assessment, control verification and emergency arrangements are resolved by the responsible competent people. This learning example does not issue an operational assessment or authorise work.
Connect chemical identity, formulation and change control to the actual validated operating information.
Teaching graphic from the linked SHAREhub source section.
Verify what is being mixed before relying on the process basis
A resin system is more than a generic name on a drum. Formulation, component identity, quantity, contamination and process conditions can affect the hazards and the basis for control. The correct document for a different product is not evidence for this one. Establish the link between the actual materials, supplier information and the approved task/process instructions.
A proposed substitution should enter the organisation’s change process before use. Do not assume that similar viscosity, colour or end-product purpose means equivalent reaction behaviour. The competent review must determine what information and validation are required, including implications for equipment, safeguards, people, emergency arrangements and waste. This course does not approve a formulation or define a safe mixing ratio.
Keep uncertainty out of the live process through identification and controlled storage/issue arrangements. The person receiving a kit needs to know its status and any restrictions. A quality acceptance note may address one specification without resolving the process hazards of a changed formulation. Record those decisions separately.
In the exercise, inspect a fictional substitute-material request beside the original process instructions. Mark every assumption that needs review before release. Identify the responsible functions rather than writing a new recipe yourself. Verify that an authorised change has actually reached the point of use, including labels, instructions and training. A completed change form is not sufficient if the old material or instructions remain available beside the charging point.
What must the hazard review examine?
Examine new initiating events, changed consequences, barrier dependencies, human tasks, abnormal modes and off-site effects. Scale the method to the hazard and complexity.
A focused multidisciplinary review may be enough for a bounded change; a complex modification may need a formal hazard and operability or other study. Test normal, start-up, shutdown, maintenance, utility failure and emergency conditions. Challenge assumptions about relief, isolation, ignition, common-cause failure, operator time and contractor interfaces. Record actions, owners and evidence needed before start. HSE COMAH plant modification and change procedures and HSE COMAH control systems.
How should chemical compatibility be assessed?
Compatibility should be assessed by reviewing the chemical inventory, SDS information, reaction hazards, storage locations, transfer routes, drains, waste streams and credible mixing scenarios.
Start with the inventory. List all chemicals, wastes, residues, cleaning chemicals, intermediates, off-spec materials and process fluids. Then identify what could meet what: shelves, bunds, drains, hoses, fill points, waste containers, shared equipment, cleaning routines and emergency response materials.
The SDS is important, especially sections on handling, storage, stability and reactivity, but it does not know your pipework, drain route, container choices or work sequence. A site-specific compatibility review should connect the SDS with the physical workplace.
For higher-risk operations, create credible scenarios: acid into hypochlorite tank, oxidiser into solvent waste, wrong road tanker connection, incompatible drain discharge, cleaning chemical into process residue, rainwater into water-reactive store, or waste drum bulking error.
Compatibility assessment steps
Step
What to assess
Evidence
Inventory
Products, raw materials, intermediates, wastes, residues and cleaners.
Chemical register and waste register.
SDS review
Sections 7, 8, 10, 11 and 13.
SDS review record.
Compatibility matrix
Which substances or classes must be separated.
Matrix or segregation chart.
Physical layout
Stores, bunds, shelves, tanks, drains, transfer points and routes.
Labels, locks, couplings, interlocks, permits, procedures and supervision.
Barrier register and test records.
Applied case
A substitute hardener is proposed because its supplier describes the same end use.
Decision and explanation
The competent change review and applicable material/process evidence for the actual formulation.
Correct decision: The competent change review and applicable material/process evidence for the actual formulation. Connect chemical identity, formulation and change control to the actual validated operating information.
Lesson 3
Recognise pressure that remains after the cycle stops
Require a verified safe energy and material state before opening equipment or breaking containment.
Photorealistic illustrative UK workplace scene. Review checks: Setting: the process operator proposes a higher transfer rate into a pressurised LPG storage vessel sharing a flare header with other protected equipment. Act: Revisit overfill, blocked outlet, external fire, thermal expansion, vapour-return failure and emergency blowdown against the changed throughput, vessel limits and common flare load. Hold / review: Do not start the higher-rate transfer if relief capacity, flare back-pressure, device availability, emergency depressurisation load or operator response is unresolved.
Recognise pressure that remains after the cycle stops
A stopped machine can retain trapped pressure, hot material and energy capable of causing movement. A closed valve may create a trapped section rather than remove the pressure. The control display and the physical state must be understood through the actual system, including connected supplies and components that can re-pressurise or move.
Do not loosen a fitting, open a guard or use a leak to test whether pressure remains. Depressurisation and material removal require the assessed competent method for the equipment and substance. Relief devices and emergency systems have defined purposes and design bases; they are not convenient routine vents for a learner to operate.
A maintenance handover should identify the isolation boundary, residual hazards, verification and responsibility for maintaining the safe state. The relevant pressure-system duties depend on the actual equipment and contents. This awareness course supplies neither a universal examination interval nor authority to decide which statutory regime applies to a particular vessel.
For the exercise, draw the boundary around a fictional injection line with a trapped branch. List the evidence required before access, including how a misleading local indication would be detected through the competent procedure. Keep the evidence request separate from instructions to perform the isolation. Work remains held if its safe state cannot be established. Restart requires the authorised handback and checks for restored protection, rather than simply reconnecting the energy after the visible task appears complete.
What do learners commonly confuse?
Pressure protection concepts are easy to memorise but harder to apply without scenario thinking.
Confusion
Better explanation
Professional test
PSV equals safe
A PSV is one component; the relief path and disposal route also matter.
Can the full route handle the credible scenario?
Relief prevents the incident
Relief usually mitigates overpressure after an initiating event.
What prevention barriers failed first?
Venting is always safe
Venting can create toxic, flammable, hot, cold or environmental hazards.
Where does the material go and who could be exposed?
Depressurisation is just opening a valve
Rate, route, low temperature, disposal and operator action matter.
Is the blowdown basis proven?
Written scheme covers all
The written scheme must be matched to real equipment and protective devices.
Does field condition match the scheme?
How are pressure systems operated and maintained?
Operate within established safe limits using effective protective devices, competent people, clear instructions and a whole-system maintenance plan; isolate and depressurise safely before intervention.
Pressure-system examination and maintenance are different. Include corrosion, leakage, alarms, relief devices, connections, pipework, environment, change and operator handover. A pressure indication of zero at one point is not proof that all stored energy is controlled.
Start and run. Control: Limits, protection and competent operation.; Stop: Unreliable reading or excursion.
Maintain. Control: Isolation, depressurisation, verification and safe access.; Stop: Trapped pressure or unknown connection.
What happens after pressure-system repair or modification?
Hold the affected system, assess the change against design and safe limits, update the written scheme when required, obtain competent examination where the scheme or law requires it, and release only after controlled testing and named acceptance.
Repairs, replacement components, changed fluids and operating conditions can alter the pressure boundary. A maintenance completion or leak test alone is not statutory examination or authority to operate.
Repair or replacement. Check: Material, design, protective devices and required examination.; Release condition: Competent evidence accepted.
Changed duty. Check: Safe limits, scheme scope and instructions.; Release condition: Updated and approved basis.
What should happen after a pressure release or alarm?
Move people clear, raise the alarm, follow the site emergency plan and keep the system isolated from further operation; do not approach a leak, adjust a relief device or reopen a vessel until the hazard and safe state are established by authorised people.
Treat vessel, line and connected process as potentially energised. Investigate cause and affected scope, protect others, obtain any required competent examination and controlled test, then require named operating acceptance.
Leak or unusual sound. Immediate action: Withdraw and warn.; Restart barrier: No approach until assessed.
Relief device operates. Immediate action: Escalate and preserve evidence.; Restart barrier: No reset-only return.
Rupture or injury. Immediate action: Emergency response and exclusion.; Restart barrier: Investigation and competent release.
The injection motor has stopped, but resin remains trapped behind a valve.
Decision and explanation
Only that motion has stopped; pressure, heat and other energy still require a verified safe state.
Correct decision: Only that motion has stopped; pressure, heat and other energy still require a verified safe state. Require a verified safe energy and material state before opening equipment or breaking containment.
Lesson 4
Keep cleaning inside the machinery safety boundary
Distinguish an operating pause from the safe isolation and access arrangements needed for intervention.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Cartons jam at a packaging transfer point. Act: Stop and hold production, keep others clear and reject the tape holding the side gate. Hold / review: Hold the line: do not start or reach in while the interlock is defeated, the drive can coast into reach, the linked feed remains energised, the air pressure is uncertain, or the task differs from the agreed method.
Keep cleaning inside the machinery safety boundary
Residue removal is an intervention into the machine, even if the production team calls it a quick clean. A paused cycle may restart, and a defeated interlock removes a barrier that users normally rely on. Assess the cleaning task with the actual machinery, hot materials, stored energy and people who could restore movement.
The appropriate response to a bypassed safeguard is to stop affected use through the site’s safe arrangements and obtain competent correction. Do not teach colleagues a workaround that becomes the ordinary method. An emergency stop or open guard is not automatically an isolation of every source. The competent safe-working system needs to establish and maintain the required state.
Plan access so that cleaning, inspection and maintenance can be performed safely. If the equipment cannot be cleaned without foreseeable dangerous access, raise the design and work-method issue rather than treating the operator’s dexterity as the control. Any exceptional powered maintenance requires its own justified competent arrangement; this course provides no such permission.
For practice, compare the normal cycle description with the residue-removal steps. Locate where the person enters the danger area and what would prevent unexpected movement or material release. Identify the hold, responsible engineering role and handback evidence. Verify that the restored interlock and other protection work as required after the intervention, and that users have a safe, usable method. A reset light alone does not show that the underlying access problem has been solved.
How can a jam, clean or repair be handled safely?
Plan the intervention before opening protection. Stop the machine, identify and isolate every relevant energy source, secure against reconnection, verify the safe condition, and prevent other people starting or entering while work continues. Use a separately engineered and authorised mode if movement is genuinely needed.
An interlock or emergency stop alone can leave electrical power, air pressure, hydraulic pressure, gravity or a coasting part available. The competent isolation plan covers linked conveyors and upstream equipment, stored loads, trapped pressure and each person working in the danger area. Do not reach in to pull material while a motor is merely stopped. HSE Maintenance of work equipment; HSE Guarding in quarries.
Intervention hold points
Stage
Decision or evidence
Before access
Identify machine, task, hazard and authorised workers; agree whether it can be done with guards in place or from outside the danger zone.
Secure
Stop, isolate and lock the applicable sources under the site procedure; each exposed worker retains personal control. Release or restrain stored energy by a competent method.
Verify
Check the intended safe state by the authorised method, including linked equipment and coasting. If the state is uncertain, hold work and escalate.
Perform and change
Use the approved tools and route. If the jam, access or energy state differs from the plan, stop, withdraw and revise the method.
Hand back
Account for people and tools; restore guards, remove locks only through the agreed process, function-check protection and authorise restart with affected operators informed.
How can maintenance itself be made safe?
Plan intervention hazards before removing guards or opening plant. Control energy, movement, height, substances, contractors and nearby operations for the whole job.
Identify every energy source, bring equipment to the required state, securely isolate, prevent reconnection and release or restrain stored energy. A stop command or open guard is not secure isolation. Use planned exceptional powered fault-finding only with competent specialists and designed protection. Coordinate group work and shift changes. HSE maintenance of work equipment and HSE L22 Safe use of work equipment.
At handback, account for people and tools, restore guards and devices, verify the affected functions and authorise a controlled restart. A permit is a coordination tool where the risk system requires it; it does not substitute for physical controls. Contractors need equipment identity, instructions, hazard information and a defined interface.
Applied case
Cleaning is routinely done with an interlock defeated during a short production pause.
Decision and explanation
Hold affected use and obtain a competent safe intervention method and restored safeguards.
Correct decision: Hold affected use and obtain a competent safe intervention method and restored safeguards. Distinguish an operating pause from the safe isolation and access arrangements needed for intervention.
Lesson 5
Prevent uncured adhesive contact throughout the task
Control contact routes at mixing, application, removal and cleanup rather than relying on the absence of symptoms.
Explore an enlarged section of hair-bearing skin, with a hand and forearm for context. Layers, glands, nerves and vessels are enlarged for clarity.
Use the task in this lesson to identify contact, repeated wet work or contamination. Which change reduces contact before relying on gloves?
educational illustration · healthy anatomy; enlarged details and teaching colours.
Photorealistic illustrative UK workplace scene. Review checks: Setting: A cleaner repeatedly handles diluted detergent and disinfectant and washes hands many times per shift. Act: The manager checks product identity, reduces wet work, selects a less harmful product where suitable, provides dosing and long-handled tools, and verifies glove compatibility. Hold / review: Stop contact with an unknown product, failed dosing or unsuitable glove; report persistent redness, itching or cracks promptly.
Prevent uncured adhesive contact throughout the task
Uncured adhesive or resin can contact the skin through tools, cuffs, surfaces and removal of contaminated protection. A small smear can be easy to transfer and difficult to notice. Assess the complete sequence, including kit preparation, application, discarded containers and the transition to clean areas. The task is not finished while contaminated tools remain available for reuse.
Use the actual substance information and task assessment to select prevention. Suitable dispensing tools, enclosure or other source controls may reduce contact before gloves are considered. Protective gloves must be appropriate to the chemical, task and expected use; a glove that looks intact is not a universal barrier. Avoid contaminating skin while taking it off.
Early reporting supports the organisation’s skin-health programme and appropriate professional advice. Do not diagnose sensitisation or promise that a symptom-free person is protected. Repeated low-level contact and contamination of clean surfaces are reasons to improve control, not to wait for a visible injury.
In the exercise, follow adhesive on a cuff through the next three actions. Identify the transfer routes and a prevention measure for each. Check whether shared tools could also mix materials from different kits, creating both exposure and process uncertainty. The solution should address the work system and its verification: correct tools, controlled waste, usable removal/washing arrangements and reporting. This awareness exercise does not select a specific glove brand or authorise a changed adhesive formulation.
How should gloves be selected and managed?
Gloves must match the substance, task, contact time, dexterity, tear risk, wearer and compatibility with other controls.
HSE glove guidance requires the material and duration to match the product and task.
Gloves are useful but often misunderstood. The right glove for one chemical may fail against another. A glove that is safe for cleaning may create entanglement risk around rotating machinery. A glove that protects against splashes may fail during immersion or long contact. A glove worn too long may trap sweat and worsen dermatitis.
The assessment should use SDS information, manufacturer compatibility data and task observation. It should also consider glove length, cuff, thickness, grip, dexterity, puncture risk, change frequency, storage, removal technique and whether workers need liners or alternative products.
Decision
What to check
Failure to avoid
Chemical compatibility
Will glove material resist the substance for the contact time?
Chemicals can harm people through inhalation, skin contact, skin absorption, eye contact, ingestion and injection.
Inhalation is often the most obvious route because airborne dusts, gases, vapours, mists and fumes can reach the nose, throat and lungs. Fine respirable particles can travel deep into the lungs; soluble gases may irritate the upper airways; some vapours can be absorbed into the bloodstream.
Skin exposure is often underestimated. Some substances damage the skin surface, some pass through the skin and affect organs, and some cause sensitisation so that later small exposures trigger a reaction. Wet work, damaged gloves, contaminated sleeves, trapped chemicals and poor washing facilities all increase risk.
Eye exposure, ingestion and injection are less frequent but can be severe. Splash injuries, contaminated hands near the mouth, eating in work areas and puncture injuries from contaminated sharps or high-pressure injection equipment should be considered in the assessment.
Elimination, enclosure, LEV, ventilation, process control and RPE.
Skin contact
Liquid, dust, paste or contaminated PPE touches skin.
Substitution, closed handling, gloves, clothing, welfare and skin checks.
Skin absorption
Substance passes through skin into the body.
Chemical-resistant PPE, hygiene and exposure-time control.
Eye contact
Splash, dust or aerosol enters the eye.
Closed transfer, splash guards, goggles, face shields and eyewash.
Ingestion
Contaminated hands, food, drink or cigarettes transfer substance to mouth.
Hygiene, clean welfare, no eating in contaminated areas and supervision.
Injection
High-pressure fluid or contaminated sharp punctures skin.
Guarding, depressurisation, sharps controls and emergency escalation.
Applied case
A worker uses the same contaminated mixing tool between two kits.
Decision and explanation
Contact prevention and the separate compatibility/identity control for the kits.
Correct decision: Contact prevention and the separate compatibility/identity control for the kits. Control contact routes at mixing, application, removal and cleanup rather than relying on the absence of symptoms.
Lesson 6
Treat resin waste as a chemical process decision
Establish waste identity and compatibility before collection or consolidation, including residual reaction and heat hazards.
Photorealistic illustrative UK workplace scene. Review checks: Chemical register: Compatibility class, SDS section 10, storage, owner and approved use. Transfer verification: Right product, tank, hose, valve lineup and ullage confirmed. Storage segregation: Acids, alkalis, oxidisers, flammables and wastes separated.
Treat resin waste as a chemical process decision
Waste does not lose its chemical properties when it enters a drum. Unreacted resin, hardener, solvent and contaminated absorbent may create a different hazard when combined. An apparently convenient common container can become an unintended mixing vessel. Identify the streams and use the organisation’s assessed segregation and collection arrangements.
Do not add material to an uncertain drum to see how it behaves. Keep access and further transfer controlled while the responsible person establishes contents and the appropriate route. A waste contractor’s availability does not establish that an unknown mixture is acceptable to store, move or treat. Applicable waste classification and permit duties depend on the UK nation and operation.
The process assessment should consider waste produced during normal work, a rejected batch and cleaning or an upset. Relevant information includes material condition and any continuing reaction or heat concern. This course gives no cooling, neutralisation, bulking or emergency venting recipe. Where an abnormal condition develops, use the planned competent response and keep people protected.
For the fictional exercise, create a waste-stream map from mixing station to collection. State what evidence confirms identity, segregation, container suitability and handover. Include what happens when a container arrives without adequate information. Verify the actual arrangement at the point of disposal rather than only reviewing the final paperwork. A labelled waste stream and an authorised collection route support control; neither gives a learner permission to combine uncertain chemicals or redesign the process.
Why are waste streams and drains high-risk mixing routes?
Waste streams and drains are high-risk because chemicals can meet out of sight after leaving the original task area.
A drain, sump, interceptor, IBC, drum or waste tank can become the mixing vessel. Workers may think each individual disposal was small, but incompatible discharges can accumulate or react in a confined space, generating heat, pressure, gas or pollution.
Waste compatibility needs a positive approval process. Unknown waste should not be bulked because it looks similar or because the container is available. Waste labels should include contents, hazards, source, date, incompatible materials and owner.
Drain maps and isolation points are important for process sites, laboratories, workshops and construction sites. If responders do not know where a drain goes, they cannot confidently control a spill or incompatible discharge.
Waste and drain controls
Control
Purpose
Evidence
Waste-stream approval
Prevents incompatible waste from being bulked.
Waste acceptance or approval record.
No unknown bulking rule
Prevents reaction from unidentified material.
Quarantine and characterisation procedure.
Drain map
Shows where spills and discharges may travel.
Current site drainage plan.
Drain protection
Stops incompatible or polluting material entering drainage.
Drain covers, valves and spill drills.
Waste labels
Communicate contents and hazards.
Label inspection and waste register.
Compatibility testing
Confirms bulking is safe where required.
Test record and acceptance criteria.
How do process conditions change dangerous substance risk?
Process conditions can turn a manageable substance into a major accident hazard by changing energy, release behaviour, reaction rate or containment demand.
Temperature, pressure, flow, agitation, catalysts, contamination, concentration and residence time can change how a substance behaves. A solvent below its flashpoint may present a different ignition risk from the same solvent sprayed as a mist. A stable process may become unstable if cooling is lost, feed rate is wrong, a catalyst is contaminated or an inhibitor is missing. A pressure system may be safe during normal flow but unsafe if a valve closes and pressure relief has not been designed for the credible case.
For process safety, the important question is not only what the substance is, but what conditions must stay inside the safe operating envelope. That envelope should define safe limits, alarms, trips, operator actions, shutdown conditions, relief assumptions, emergency isolation and the consequences of leaving the envelope.
Operators should know which limits are safety-critical and what they must do when those limits are approached. Engineers should be able to show the design basis. Managers should know whether inspection, maintenance and change control protect those assumptions.
Process condition questions - Process condition questions
Question
Why it matters
Evidence to check
What are the safe operating limits?
Limits define when operation is safe, abnormal or unacceptable.
Operating procedures, control system data, alarm set points and trip logic.
What happens if cooling, flow or agitation is lost?
Loss of control can create runaway reaction, overpressure or off-spec hazardous material.
HAZOP records, relief calculations, emergency procedures and drills.
Can the substance flash, boil, decompose or polymerise?
Physical or chemical change can create pressure, vapour, heat or blockage.
SDS, process safety data, laboratory data and specialist review.
Is relief sized for the credible scenario?
A relief device sized for one case may not protect against another.
Relief design basis, inspection records and change history.
Can operators see the real state of the plant?
Poor indication, alarm flooding or mistrusted instruments can delay response.
Control room design, alarm rationalisation and operator feedback.
Applied case
Resin, hardener and solvent residues are proposed for one unverified waste drum.
Decision and explanation
The responsible assessment of identity, compatibility, container and authorised waste arrangements.
Correct decision: The responsible assessment of identity, compatibility, container and authorised waste arrangements. Establish waste identity and compatibility before collection or consolidation, including residual reaction and heat hazards.
Lesson 7
180°C resin contact and hot tooling
Do not touch or open the cell until its approved thermal, pressure and reaction conditions are verified.
Photorealistic illustrative UK workplace scene. Review checks: Setting: A fictional chemical process adds material to a reactor within an assessed operating envelope. Act: The competent team considers heat generation, removal, mixing, conversion and hidden accumulation using the actual reaction evidence. Hold / review: Use the assessed abnormal-response procedure; do not improvise feed, cooling, quench or relief settings.
Understand the activity and how harm develops
This scene uses a nominal 180°C condition to make thermal hazards visible. Real resin systems have different approved conditions and limits. A cycle-complete signal does not mean that the mould, trapped resin or component has cooled enough for handling.
Look for the route from hot surfaces and pressurised material to the worker’s hands and face. Opening a guard can reveal both a burn surface and a release path. Heat-resistant gloves do not make a pressurised or reacting system safe to open.
Use designed enclosure, insulated surfaces and handling methods, followed by a verified release condition. The actual material and equipment instructions determine the process. If a burn occurs, activate first-aid arrangements and follow current clinical guidance; do not remove adhered material by force or improvise chemical treatment.
Recognise the evidence boundary
Question
Case evidence
What is observed?
The injection cell displays a nominal 180°C condition and freshly exposed tooling remains hot.
How can harm occur?
Hot resin or tooling can cause serious burns; escaping material may also expose skin and eyes chemically.
What information is needed?
Check the specified process and material rather than copying 180°C.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Provide enclosure, insulation and mechanical handling for hot components.
Accountable work arrangement
Avoid contact with hot tooling. Use designed enclosure and handling. Verify thermal and pressure release. Apply product-specific protection.
Release verification
Confirm hot parts remain identified and segregated until released.
Apply this at work
Do not touch or open the cell until its approved thermal, pressure and reaction conditions are verified.
How should reaction hazards be managed through the lifecycle?
Carry reaction knowledge from laboratory concept through design, commissioning, batches, cleaning, maintenance, change and emergency response.
At development stage, identify intended and unintended reactions, heat and gas release, decomposition and contaminant effects. A small-scale result may not transfer to a larger vessel because heat generation grows with volume while heat removal depends on surface area and equipment. Commissioning confirms the installed cooling, agitation, controls, relief and emergency arrangements against the design basis.
Who checks the reaction basis at each stage
Stage
Decision and evidence
Development and scale-up
Chemist and engineer select competent tests, document heat/gas and uncertainty, then approve the scale and safe envelope before larger trials.
Design and commissioning
Process and relief specialists define credible upsets, safeguard performance and discharge destination; commissioning proves installed functions before hazardous charge.
Operation and cleaning
Operator follows batch sequence and hold points; supervisor checks trends, deviations, residues, cleaning chemistry and waste route.
Maintenance and change
Maintainer proves safe isolation and hand-back; process owner reviews recipe, supplier, concentration, batch size, software and equipment changes before restart.
Emergency and recovery
Incident lead applies the site scenario plan and keeps people clear; competent team reviews damage and barrier restoration before authorising return to service.
A valve left partly closed after maintenance, a new supplier impurity or a shared drain can undo a good laboratory study. Each lifecycle handover needs a named owner and evidence, not only a signed form.
Applied case
The cycle light turns complete while the mould is still hot.
Decision and explanation
The approved cooling and access checks for that process.
A status light alone does not establish safe contact. Gloves cannot control a possible hot pressurised release. The fictional process temperature is not a human-contact limit.
Lesson 8
Exothermic reaction and loss of temperature control
Withdraw and activate the approved response to uncontrolled reaction; do not improvise intervention.
Photorealistic illustrative UK workplace scene. Review checks: Setting: A fictional chemical process adds material to a reactor within an assessed operating envelope. Act: The competent team considers heat generation, removal, mixing, conversion and hidden accumulation using the actual reaction evidence. Hold / review: Use the assessed abnormal-response procedure; do not improvise feed, cooling, quench or relief settings.
Understand the activity and how harm develops
The critical relationship is between heat generated and heat removed. If the reacting resin produces heat faster than the system removes it, temperature can accelerate the reaction further. Heater shutdown removes one input but does not necessarily stop this feedback.
Recipe, quantity, contamination, addition order and heat-transfer performance affect the hazard. A laboratory success cannot automatically validate a larger batch. The fictional 180°C condition provides no safe operating envelope, emergency setpoint or resin-specific design instruction.
Prevention and protection require a competent reaction-hazard basis, validated limits, interlocks and designed containment or relief. Operators follow the approved alarm response and withdraw as required. Never improvise water addition, quenching, opening, pouring or venting; an engineered emergency system is not permission for manual imitation.
Recognise the evidence boundary
Question
Case evidence
What is observed?
The resin temperature rises unexpectedly while the cooling indication is abnormal.
How can harm occur?
Accelerating reaction can generate heat, gas and pressure, causing release, fire or equipment failure.
What information is needed?
Check the reaction assessment covers credible loss of cooling and contamination.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Provide validated cooling, independent protective trips and safe containment.
Accountable work arrangement
Validate the reaction safety basis. Maintain cooling and protective functions. Control recipe and scale changes. Withdraw under the approved response.
Release verification
Require competent investigation and release after any abnormal temperature trend.
Apply this at work
Withdraw and activate the approved response to uncontrolled reaction; do not improvise intervention.
How should reaction hazards be managed through the lifecycle?
Carry reaction knowledge from laboratory concept through design, commissioning, batches, cleaning, maintenance, change and emergency response.
At development stage, identify intended and unintended reactions, heat and gas release, decomposition and contaminant effects. A small-scale result may not transfer to a larger vessel because heat generation grows with volume while heat removal depends on surface area and equipment. Commissioning confirms the installed cooling, agitation, controls, relief and emergency arrangements against the design basis.
Who checks the reaction basis at each stage
Stage
Decision and evidence
Development and scale-up
Chemist and engineer select competent tests, document heat/gas and uncertainty, then approve the scale and safe envelope before larger trials.
Design and commissioning
Process and relief specialists define credible upsets, safeguard performance and discharge destination; commissioning proves installed functions before hazardous charge.
Operation and cleaning
Operator follows batch sequence and hold points; supervisor checks trends, deviations, residues, cleaning chemistry and waste route.
Maintenance and change
Maintainer proves safe isolation and hand-back; process owner reviews recipe, supplier, concentration, batch size, software and equipment changes before restart.
Emergency and recovery
Incident lead applies the site scenario plan and keeps people clear; competent team reviews damage and barrier restoration before authorising return to service.
A valve left partly closed after maintenance, a new supplier impurity or a shared drain can undo a good laboratory study. Each lifecycle handover needs a named owner and evidence, not only a signed form.
Applied case
Temperature keeps rising after heater shutdown.
Decision and explanation
The reaction may still generate heat; follow the emergency response.
Remaining nearby increases exposure to a possible release. An improvised quench or opening can worsen reaction and release. Heater-off is not proof that the chemistry has stopped.
Lesson 9
Injection pressure and safe depressurisation
Never loosen a fitting to test whether pressure remains.
Photorealistic illustrative UK workplace scene. Review checks: Setting: the process operator proposes a higher transfer rate into a pressurised LPG storage vessel sharing a flare header with other protected equipment. Act: Revisit overfill, blocked outlet, external fire, thermal expansion, vapour-return failure and emergency blowdown against the changed throughput, vessel limits and common flare load. Hold / review: Do not start the higher-rate transfer if relief capacity, flare back-pressure, device availability, emergency depressurisation load or operator response is unresolved.
Understand the activity and how harm develops
Trace the injection line from pump to mould, including valves, accumulators and blocked sections. Pressure may remain locally even when another gauge shows zero. A solidified plug can isolate a pocket that becomes dangerous when heated or disturbed.
The safe method must identify the actual equipment and material, secure its energy and supply boundaries, and control the release through a designed route. A relief device protects against specified conditions; it is not a routine access procedure or a universal drain point.
Only authorised competent personnel perform the approved depressurisation and verification. Keep people outside potential discharge paths and account for temperature and chemical reaction as well as pressure. Unexplained readings, blockage or failed indication require escalation before a connection is loosened.
Recognise the evidence boundary
Question
Case evidence
What is observed?
A stopped injection unit still contains resin and trapped pressure behind a closed valve.
How can harm occur?
Opening a connection can eject hot material or move equipment unexpectedly.
What information is needed?
Check the isolation boundary includes the mould and connected accumulators.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Provide suitable isolation, indication and designed pressure-release paths.
Accountable work arrangement
Identify every trapped-pressure section. Secure the complete isolation boundary. Use designed depressurisation routes. Verify heat and reaction conditions.
Release verification
Confirm residual heat and reaction hazards are also cleared for access.
Apply this at work
Never loosen a fitting to test whether pressure remains.
How might a pressure relief review work in practice?
A worked example shows how technical relief questions become operational decisions.
Crownway Fuels Ltd plans to increase transfer rate into a pressurised LPG storage vessel. The old relief calculation assumed a lower filling rate and a different fire case. The change also affects the common flare header and emergency depressurisation load. A weak review would update the operating procedure only. A competent review would treat this as management of change affecting safety-critical pressure protection.
The review should ask whether overfill, blocked outlet, external fire, thermal expansion, vapour return failure and emergency depressurisation are still within the protection envelope. It should confirm relief capacity, flare load, valve testing, operator alarm response, shutdown logic and emergency plans before authorising the change.
Review step
Question
Evidence expected
Define change
What throughput, inventory, pressure or operating limit changes?
MOC scope and design intent.
Identify scenarios
Which overpressure cases are affected?
Relief basis review.
Check capacity
Can PSV/disposal route handle revised demand?
Sizing calculation and flare review.
Check controls
Are alarms, trips and emergency shutdown still adequate?
Cause and effect and proof-test evidence.
Check operation
Do operators understand new limits and emergency action?
Procedure, training and drill record.
Authorise
Are open actions safe to close after start or must they be closed first?
Readiness gate and action risk acceptance.
Operational example: LPG vessel change and relief evidence
Task material and setting: Crownway Fuels Ltd proposes a higher transfer rate into a pressurised LPG storage vessel sharing a flare header with other protected equipment.
People and prerequisites: The process engineer owns revised scenarios and capacity; mechanical and instrumentation specialists check devices and trips; operations owns the lineup and start-up gate.
Before: Revisit overfill, blocked outlet, external fire, thermal expansion, vapour-return failure and emergency blowdown against the changed throughput, vessel limits and common flare load.
During: Commission to a staged plan with verified alarms, shutdown logic, valve lineup and header capacity; monitor pressure and transfer rate against approved limits.
Hold or stop: Do not start the higher-rate transfer if relief capacity, flare back-pressure, device availability, emergency depressurisation load or operator response is unresolved.
Completion and hand back: Authorise the new operating envelope only after calculations, proof tests, procedures and outstanding safety-critical actions are accepted by the competent owners.
Evidence: Management-of-change scope, LPG properties and scenario basis, vessel/relief calculations, flare study, proof-test records, lineup check, training and signed readiness release.
Hold access and resolve the trapped-pressure uncertainty.
The first movement may release a high-energy jet. The reading may not represent the isolated section. Sound cannot verify pressure or temperature.
Lesson 10
Machine interlocks, cleaning and isolation
Stop and isolate the machine when a safety interlock is defeated or unreliable.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Cartons jam at a packaging transfer point. Act: Stop and hold production, keep others clear and reject the tape holding the side gate. Hold / review: Hold the line: do not start or reach in while the interlock is defeated, the drive can coast into reach, the linked feed remains energised, the air pressure is uncertain, or the task differs from the agreed method.
Understand the activity and how harm develops
The cell contains several energies: electrical supply, hydraulic clamping, pressure, heat and reacting material. A paused sequence may restart from a remote command or when a fault clears. Defeating the interlock removes a protective function intended to prevent access during danger.
Cleaning and blockage removal need an assessed method that avoids entry where practicable. Where access is necessary, identify and secure every relevant energy source and support parts that can move under gravity. Isolation must be verified by a competent method for this machine.
After work, account for people, tools and removed guards, restore protective functions and complete controlled handback. Investigate why production pressure or poor access encouraged bypassing. Repeated resetting without fault resolution is evidence of a failing system, not normal operation.
Recognise the evidence boundary
Question
Case evidence
What is observed?
A guard interlock is defeated so residue can be removed during a paused cycle.
How can harm occur?
The machine can close, inject or move while a person is inside its danger zone.
What information is needed?
Check the intervention method covers every energy and material connection.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Maintain effective guarding, interlocks and secure isolation facilities.
Accountable work arrangement
Avoid access during hazardous operation. Restore guards and interlocks. Secure and verify all energy. Complete competent handback.
Release verification
Confirm guards and interlocks are restored and tested before restart.
Apply this at work
Stop and isolate the machine when a safety interlock is defeated or unreliable.
How does an unguarded machine injure people?
Hazardous motion reaches a person when a hand, clothing or body can enter a nip, cutting path, closing gap or moving enclosure before the machine reaches a safe state. The immediate harm can be entanglement, crushing, amputation, laceration or impact; survivors may have lasting disability.
A rotating roller grips clothing or a hand and draws the limb into a narrowing gap. A ram or gate closes on a person and compresses tissue against a fixed surface. A blade cuts on contact; a broken tool or workpiece can strike the eye or body. Unexpected restart or stored pressure can create the same contact while someone is clearing a jam. Speed, mass, force, coast-down time, reach distance, poor visibility, bypassed guards and linked equipment change the chance and severity. HSE Introduction to machinery safety; HSE hierarchy of controls.
Machinery harm mechanisms and stop signs
Task or exposure
Route and likely harm
Early sign and stop point
Feeding rollers or conveyors
An in-running nip draws clothing, hair or a hand into moving surfaces; crush injury, fracture, degloving or amputation can follow.
Guard gap, reachable nip, loose clothing near motion or repeated snagging: stop use and prevent access.
Power press, mixer or driven gate
A moving part closes against another surface or unexpectedly restarts; crushing, shearing or entrapment may cause major injury or death.
Gate can open while motion remains, unexpected reset, person able to remain inside or changed stopping time: hold use.
Saw, cutter or ejected workpiece
Contact cuts or severs tissue; fragments can penetrate an eye or strike a person.
Missing blade guard, damaged enclosure, altered feed or unexpected ejection: stop and investigate.
Jam clearing or maintenance
Stored pneumatic, hydraulic or gravitational energy or linked machinery moves after a motor stop; hands or whole body can be trapped.
Unknown energy state, no personal control of isolation, coasting or a changed jam: withdraw and seek competent help.
These are primarily acute injury mechanisms. Long-term loss of function or disability can follow severe injury; this page does not imply a separate chronic exposure limit for guarding. Machine-specific injury patterns still require the actual risk assessment. HSE explains the machine hazard and safeguard route in Official guidance.
Applied case
The machine is paused and the door switch is taped closed.
Decision and explanation
Stop production and use the authorised isolation and repair process.
A bypassed protective function requires controlled correction. A watcher cannot replace secure isolation. A short intervention can still coincide with unexpected movement.
Lesson 11
Adhesive mixing and skin sensitisation
Stop uncontrolled skin contact or uncertain mixing and obtain competent advice.
Photorealistic illustrative UK workplace scene. Review checks: Setting: A cleaner repeatedly handles diluted detergent and disinfectant and washes hands many times per shift. Act: The manager checks product identity, reduces wet work, selects a less harmful product where suitable, provides dosing and long-handled tools, and verifies glove compatibility. Hold / review: Stop contact with an unknown product, failed dosing or unsuitable glove; report persistent redness, itching or cracks promptly.
Understand the activity and how harm develops
Resin and hardener can reach skin through splashes, contaminated tools and glove removal. Repeated low-level contact may matter even when there is no immediate burn. Some substances can sensitise a person, making later exposure a continuing health problem.
Confirm the actual product and approved mixing method. Do not assume a generic disposable glove resists every adhesive or solvent. Selection needs chemical compatibility, contact duration and task information, while dispensing tools and containers must not introduce incompatible residues.
Prefer controlled dispensing and no-touch handling. Keep contaminated tools and waste within the work area, provide washing arrangements and act promptly on symptoms. A cream or a clean-looking glove does not replace the COSHH assessment, suitable protection and occupational-health arrangements.
Recognise the evidence boundary
Question
Case evidence
What is observed?
Uncured adhesive is on a glove cuff and open mixing tools are used between different kits.
How can harm occur?
Skin contact can cause irritation or sensitisation; wrong mixing can create a reaction or product defect.
What information is needed?
Check product identity and approved kit or mixing instructions.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Provide suitable containment, dedicated tools and clean work surfaces.
Accountable work arrangement
Use controlled adhesive dispensing. Verify product and mixing method. Prevent and remove contamination safely. Select compatible skin and eye protection.
Release verification
Observe removal and cleaning without contaminating skin or shared handles.
Apply this at work
Stop uncontrolled skin contact or uncertain mixing and obtain competent advice.
How does workplace exposure damage skin?
Skin damage develops when contact, duration, frequency and susceptibility exceed the skin's ability to repair.
HSG262 describes exposure routes and the controls needed to protect the skin barrier.
The exposure pathway is not always a dramatic splash. Many occupational skin diseases develop through small repeated contacts: wet hands during cleaning, detergent residue after washing, cement on wrists, oil under gloves, solvent wipes used without the right gloves, abrasive dust in cuffs or sweaty gloves worn for hours.
Skin risk assessment should therefore look at contact route, contact time, frequency, substance properties, glove breakthrough, handwashing, drying, moisturising, seasonal effects, pre-existing vulnerability and whether the worker can realistically avoid contact during the task.
A glove looks intact but is contaminated with uncured adhesive.
Decision and explanation
Follow the assessed change and removal method and check skin contact.
Contact time and compatibility determine suitability. The solvent can spread contamination or degrade protection. Visual integrity alone does not establish chemical protection.
Lesson 12
Resin and solvent waste segregation
Do not mix uncertain waste or approach a reacting container for improvised intervention.
Photorealistic illustrative UK workplace scene. Review checks: Chemical register: Compatibility class, SDS section 10, storage, owner and approved use. Transfer verification: Right product, tank, hose, valve lineup and ullage confirmed. Storage segregation: Acids, alkalis, oxidisers, flammables and wastes separated.
Understand the activity and how harm develops
Offcuts, uncured resin, contaminated wipes and cleaning solvent are different waste streams. A container marked waste does not establish what can safely enter it. Mixed reactive material can continue curing and generating heat after the production job has ended.
Identify contents and assess compatibility, quantity, container and storage conditions before collection. A small production mixture and a larger waste accumulation have different heat-removal behaviour. Never use an empty-looking drum without considering residues or mix materials to reduce the number of containers.
Use suitable labelled containers and keep incompatible streams separate. Collection arrangements need accurate descriptions and a suitable authorised destination. If a container heats, bulges or vents, withdraw and activate the assessed response; do not open, pour, dilute or quench it as an improvised remedy.
Recognise the evidence boundary
Question
Case evidence
What is observed?
Resin residues, hardener and solvent waste are being tipped into a common unverified drum.
How can harm occur?
Incompatible or reactive waste can generate heat, pressure, fire or harmful vapour.
What information is needed?
Check labels describe actual contents and relevant hazards.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Provide compatible containers and separated storage with containment.
Accountable work arrangement
Identify each waste stream. Prevent incompatible mixing. Use suitable containers and segregation. Withdraw from reacting waste.
Release verification
Confirm collection instructions preserve segregation and traceability.
Apply this at work
Do not mix uncertain waste or approach a reacting container for improvised intervention.
How should chemical compatibility be assessed?
Compatibility should be assessed by reviewing the chemical inventory, SDS information, reaction hazards, storage locations, transfer routes, drains, waste streams and credible mixing scenarios.
Start with the inventory. List all chemicals, wastes, residues, cleaning chemicals, intermediates, off-spec materials and process fluids. Then identify what could meet what: shelves, bunds, drains, hoses, fill points, waste containers, shared equipment, cleaning routines and emergency response materials.
The SDS is important, especially sections on handling, storage, stability and reactivity, but it does not know your pipework, drain route, container choices or work sequence. A site-specific compatibility review should connect the SDS with the physical workplace.
For higher-risk operations, create credible scenarios: acid into hypochlorite tank, oxidiser into solvent waste, wrong road tanker connection, incompatible drain discharge, cleaning chemical into process residue, rainwater into water-reactive store, or waste drum bulking error.
Compatibility assessment steps
Step
What to assess
Evidence
Inventory
Products, raw materials, intermediates, wastes, residues and cleaners.
Chemical register and waste register.
SDS review
Sections 7, 8, 10, 11 and 13.
SDS review record.
Compatibility matrix
Which substances or classes must be separated.
Matrix or segregation chart.
Physical layout
Stores, bunds, shelves, tanks, drains, transfer points and routes.
Labels, locks, couplings, interlocks, permits, procedures and supervision.
Barrier register and test records.
Applied case
Only a little hardener remains in the pot.
Decision and explanation
Only if the assessed waste arrangement explicitly permits that identified material.
An improvised addition can make incompatibility worse. Quantity alone does not establish compatibility. An uncontrolled test can initiate a dangerous reaction.
Lesson 13
Hold the process without inventing an emergency recipe
Separate abnormal process response, worker protection and controlled recovery in a resin case.
Photorealistic illustrative UK workplace scene. Review checks: Setting: A fictional chemical process adds material to a reactor within an assessed operating envelope. Act: The competent team considers heat generation, removal, mixing, conversion and hidden accumulation using the actual reaction evidence. Hold / review: Use the assessed abnormal-response procedure; do not improvise feed, cooling, quench or relief settings.
Hold the process without inventing an emergency recipe
This additional fictional case begins before a delayed resin run. A substitute hardener has arrived, the original process instruction remains at the cell and a production note says to use the usual quantity. During preparation, a cooling indication becomes abnormal. The machine is then stopped, but material remains in a trapped branch. A cleaning workaround has defeated an interlock, and mixed residues are waiting beside an unverified common waste drum.
Do not solve the case by choosing a new temperature, adding a cooling substance or opening a fitting. The course is an awareness exercise, not a process-design or emergency-operating instruction. Keep people protected through the assessed response and communicate the actual material, indications, changes and restrictions to the competent process and engineering functions. The nominal temperature displayed in the native scene is not a validated recipe for this added case.
Establish independent holds. The material substitution needs a competent review of the actual formulation and process basis. The abnormal cooling or temperature behaviour needs the applicable operating/emergency response. The stopped equipment needs a verified safe energy/material state before access. The bypassed interlock needs a safe intervention method and restored protection. Each may involve different evidence even when one controller coordinates the area.
Maintain the exposure boundary during recovery. Hot contact, skin contamination and pressure release are separate mechanisms; controlling one does not prove the others are controlled. Do not allow an uncertain waste stream to become the place where the process uncertainty is hidden. Identify residues, prevent unauthorised additions and obtain the assessed segregation and disposal route through the responsible people.
For restart, ask what proves the change has been accepted, safeguards restored and people prepared. A repaired indication does not validate a substitute formulation. A reset machine does not prove a trapped branch is safe to open. A waste collection booking does not establish compatibility. Retain satisfactory evidence where it remains applicable, and record exactly where the current basis is missing.
Prepare a fictional recovery board with material, process condition, intervention, exposure and waste rows. Give each a current safe state, competent owner and verification needed before its restriction changes. Practise explaining the board to the incoming shift without issuing operating commands or signing a real permit. The objective is to preserve the boundaries and ask the right evidence questions while the competent response manages the actual system.
What evidence shows reaction hazards are controlled?
The record must connect chemistry and credible scenarios to operating limits, barriers, owners and current test results. A historic study or an unreviewed batch sheet is not enough.
The process owner should be able to trace a material and a batch from test data to design and daily operation. This is particularly important after a near miss, supplier change, maintenance or scale-up.
For a semi-batch reaction, the evidence must connect the laboratory heat-release data to the authorised addition rate, cooling capacity, alarm and trip settings, relief basis, operator checks and the response to a failed cooling service. The release owner should compare the actual recipe, charge size and plant state with those assumptions before the batch starts; a change in feed composition or unavailable trip requires a fresh technical decision, not a handwritten note on the old batch sheet. HSE reaction testing guidance and control-system guidance support this chain.
Evidence that makes the basis of safety reviewable
Record
What it must show
Reaction hazard file
Materials, thermal and gas data, compatibility, uncertainty, credible upsets and a competent review of scale.
Design and safeguarding basis
Cooling and mixing capability, safe envelope, controls, trips, relief/vent destination and mitigation performance.
Work records
Batch trends, addition and hold points, alarms, deviations, raw-material identity and operator decisions.
Change and hand-back
MOC decisions, maintenance tests, commissioning, open actions, competent sign-off and restart authority.
Assurance and learning
Critical-barrier tests, impairments, near misses, drills, action closure and management review of repeated weak signals.
The site-specific safety basis and applicable law set test frequency, alarm limits and required records. An HSG254 indicator is an assurance signal, not a legal exposure limit.
Worked evidence chain: cooling loss
Illustrative chain: recipe R3 and its representative thermal-test conditions → credible cooling loss with accumulated unreacted feed → documented heat-removal and accumulation assumptions → installed cooling, independent feed trip and assessed relief → traceable commissioning/proof records → release by the process owner with the competent process engineer. Each arrow needs an identified record; this is a reasoning example, not a plant design or setpoint.
If the feed trip and normal temperature control share the failed sensor or power supply, record that dependency. If emergency cooling uses the same unavailable coolant, two labels do not create two independent barriers. Hold the recipe change or restart while the assumption is invalid; the engineer resolves dependencies and proves the revised safeguard before the process owner accepts release.
A pre-start review confirms the installed change, safety functions, procedures, competence and emergency arrangements match the approved basis before hazardous material or energy is introduced.
Check punch-list items by consequence, pressure or leak tests as applicable, trip and alarm functions, valve line-up, control-system configuration, isolations removed under control, updated drawings and operator training. A test result must name the function and acceptance criteria. Do not transfer a temporary work permit into permanent operating approval. HSE COMAH plant modification and change procedures, HSE COMAH control systems and HSE COMAH operating procedures.
How can maintenance itself be made safe?
Plan intervention hazards before removing guards or opening plant. Control energy, movement, height, substances, contractors and nearby operations for the whole job.
Identify every energy source, bring equipment to the required state, securely isolate, prevent reconnection and release or restrain stored energy. A stop command or open guard is not secure isolation. Use planned exceptional powered fault-finding only with competent specialists and designed protection. Coordinate group work and shift changes. HSE maintenance of work equipment and HSE L22 Safe use of work equipment.
At handback, account for people and tools, restore guards and devices, verify the affected functions and authorise a controlled restart. A permit is a coordination tool where the risk system requires it; it does not substitute for physical controls. Contractors need equipment identity, instructions, hazard information and a defined interface.
Applied case
A resin upset combines an unreviewed substitution, abnormal cooling, trapped pressure, defeated interlock and uncertain residues.
Decision and explanation
Protect people and maintain separate holds while competent owners establish the process, access and waste evidence.
Correct decision: Protect people and maintain separate holds while competent owners establish the process, access and waste evidence. Separate abnormal process response, worker protection and controlled recovery in a resin case.
Lesson 14
Take a verified action into the workplace
Connect one actual task to an owner, evidence and a clear release or escalation decision.
Photorealistic illustrative UK workplace scene. Review checks: Setting: A fictional chemical process adds material to a reactor within an assessed operating envelope. Act: The competent team considers heat generation, removal, mixing, conversion and hidden accumulation using the actual reaction evidence. Hold / review: Use the assessed abnormal-response procedure; do not improvise feed, cooling, quench or relief settings.
Turn awareness into a practical question
Awareness in an original fictional aerospace manufacturing and airport-interface site. GB occupational guidance has separate NI routes; environmental duties depend on the UK nation and permit. This course does not confer engineering, aircraft maintenance, product-release, lifting, rescue, driving or airside authorisation.
Choose one relevant operation from the course. Describe the person or environment at risk, the mechanism of harm and the exact condition that needs controlling. Separate an observation from a conclusion. A display, signature, badge or clean appearance answers only a limited question.
Use the included practice resources to prepare a fictional task brief, risk review or verification question. Decide which competent role owns the decision and which evidence must be available before work restarts or work is released. Keep worker protection, public exclusion, task acceptance and environmental decisions distinct where required.
At work, use your actual approved arrangements. Report uncertainty and preserve the relevant hold, restriction or safe state while it is resolved. Confirm that the action addressed the original harm route and check whether another shift, load, cleaning task or maintenance change could reintroduce it.
Course completion records awareness learning. It does not establish practical competence, certify an organisation or authorise specialist, clinical, maintenance, chemical or emergency work.
What evidence shows reaction hazards are controlled?
The record must connect chemistry and credible scenarios to operating limits, barriers, owners and current test results. A historic study or an unreviewed batch sheet is not enough.
The process owner should be able to trace a material and a batch from test data to design and daily operation. This is particularly important after a near miss, supplier change, maintenance or scale-up.
For a semi-batch reaction, the evidence must connect the laboratory heat-release data to the authorised addition rate, cooling capacity, alarm and trip settings, relief basis, operator checks and the response to a failed cooling service. The release owner should compare the actual recipe, charge size and plant state with those assumptions before the batch starts; a change in feed composition or unavailable trip requires a fresh technical decision, not a handwritten note on the old batch sheet. HSE reaction testing guidance and control-system guidance support this chain.
Evidence that makes the basis of safety reviewable
Record
What it must show
Reaction hazard file
Materials, thermal and gas data, compatibility, uncertainty, credible upsets and a competent review of scale.
Design and safeguarding basis
Cooling and mixing capability, safe envelope, controls, trips, relief/vent destination and mitigation performance.
Work records
Batch trends, addition and hold points, alarms, deviations, raw-material identity and operator decisions.
Change and hand-back
MOC decisions, maintenance tests, commissioning, open actions, competent sign-off and restart authority.
Assurance and learning
Critical-barrier tests, impairments, near misses, drills, action closure and management review of repeated weak signals.
The site-specific safety basis and applicable law set test frequency, alarm limits and required records. An HSG254 indicator is an assurance signal, not a legal exposure limit.
Worked evidence chain: cooling loss
Illustrative chain: recipe R3 and its representative thermal-test conditions → credible cooling loss with accumulated unreacted feed → documented heat-removal and accumulation assumptions → installed cooling, independent feed trip and assessed relief → traceable commissioning/proof records → release by the process owner with the competent process engineer. Each arrow needs an identified record; this is a reasoning example, not a plant design or setpoint.
If the feed trip and normal temperature control share the failed sensor or power supply, record that dependency. If emergency cooling uses the same unavailable coolant, two labels do not create two independent barriers. Hold the recipe change or restart while the assumption is invalid; the engineer resolves dependencies and proves the revised safeguard before the process owner accepts release.
A pre-start review confirms the installed change, safety functions, procedures, competence and emergency arrangements match the approved basis before hazardous material or energy is introduced.
Check punch-list items by consequence, pressure or leak tests as applicable, trip and alarm functions, valve line-up, control-system configuration, isolations removed under control, updated drawings and operator training. A test result must name the function and acceptance criteria. Do not transfer a temporary work permit into permanent operating approval. HSE COMAH plant modification and change procedures, HSE COMAH control systems and HSE COMAH operating procedures.
How can maintenance itself be made safe?
Plan intervention hazards before removing guards or opening plant. Control energy, movement, height, substances, contractors and nearby operations for the whole job.
Identify every energy source, bring equipment to the required state, securely isolate, prevent reconnection and release or restrain stored energy. A stop command or open guard is not secure isolation. Use planned exceptional powered fault-finding only with competent specialists and designed protection. Coordinate group work and shift changes. HSE maintenance of work equipment and HSE L22 Safe use of work equipment.
At handback, account for people and tools, restore guards and devices, verify the affected functions and authorise a controlled restart. A permit is a coordination tool where the risk system requires it; it does not substitute for physical controls. Contractors need equipment identity, instructions, hazard information and a defined interface.
Applied case
The shift action log says “training completed, issue closed”. It records no condition check, work status or task owner.
Decision and explanation
The accountable person verifies the task-specific control and records the justified decision.
Learning supports the decision; evidence that the relevant control works is needed before the responsible person closes the action.
Match the nine hazard symbols
End-of-course revision · Drag each symbol to its hazard name, or use the menu on each card with touch or keyboard. This is practice alongside the separate final assessment.
Acute toxicity
Corrosive
Explosive
Flammable
Gas under pressure
Harmful / irritant
Hazardous to the environment
Oxidising
Serious health hazard
Match all nine symbols, then check your choices.
Need the reference table?Chemical hazard pictograms · examples and checksOptional reference · all nine symbols · does not change assessment requirements
READ THE LABEL · UNDERSTAND THE TASK
Recognise the symbol. Read the full label. Assess the actual task.
Examples illustrate possible uses of a symbol, not the classification of every formulation. A product can carry several pictograms. Check its current label, hazard statements and matching safety data sheet (SDS).
CLP/GHS hazard pictograms: meanings and illustrative examples
Pictogram and hazard
What it can mean
Example and question before work
ExplosiveGHS01
Explosion, blast or projection hazards; also certain self-reactive substances and organic peroxides.
Example: Certain fireworks or reactive chemical products.Ask: Does the authorised task account for impact, heat and the product’s stability limits?
FlammableGHS02
Can ignite; also used for certain self-heating, pyrophoric or water-reactive hazards.
Example: Petrol or some solvent-based products.Ask: What could release vapour or ignite it during this task, including nearby work?
OxidisingGHS03
Can cause or intensify fire; some strong oxidisers present an explosion hazard.
Example: Oxygen or certain oxidising chemicals.Ask: What incompatible materials and contamination must the assessed storage and connection keep apart?
Gas under pressureGHS04
Pressurised gas may burst if heated; refrigerated gas can cause cold burns.
Example: Compressed-gas cylinders.Ask: Have the gas identity, cylinder, connection and pressure or temperature hazards been checked?
CorrosiveGHS05
May damage metals, cause severe skin burns or cause serious eye damage; read the stated hazard.
Example: Certain drain cleaners, acids or alkalis.Ask: Which contact and splash routes must be prevented in this actual handling or dilution task?
Acute toxicityGHS06
Can be toxic or fatal after short exposure through the stated route.
Example: Methanol or certain pesticide products.Ask: Which exposure routes and emergency arrangements does this product’s information identify?
Harmful / irritantGHS07
May indicate harmful acute toxicity, irritation, skin sensitisation, drowsiness or dizziness; also ozone-layer hazards.
Example: Some detergents or cleaning products.Ask: What do the hazard statements say? Do not dismiss this as a harmless or mild product.
Serious health hazardGHS08
Can indicate cancer, genetic or reproductive harm, organ damage, respiratory sensitisation or aspiration hazard.
Example: Petrol or some sensitising chemical products.Ask: Which particular health effect is stated, and how does the task prevent the relevant exposure?
Hazardous to the environmentGHS09
Hazardous to aquatic life, potentially with long-lasting effects.
Example: Certain pesticides, biocides or fuels.Ask: How will the assessed arrangements prevent release to drains, water or soil?
Read beyond the picture · Open a prompt to compare the explanation.
Is the exclamation mark the same as the chest-starburst symbol?
No. The two symbols communicate different groups of hazards. Read the actual hazard statements: skin sensitisation and respiratory sensitisation are not interchangeable, and neither symbol specifies the complete task controls.
Does a bottle with no pictogram prove the task is safe?
No. Work may generate hazardous dust, fume or mist, and exposure depends on the task. Resolve missing or conflicting identification before use. A pictogram is not a compatibility chart or a complete workplace risk assessment.
Which information turns recognition into a useful work decision?
Match the product and SDS revision. Read the hazard statements and relevant SDS sections for handling, storage, exposure control, emergencies and reactivity together. Then check the actual task assessment and controls. A safety data sheet is not itself a COSHH assessment.